Rustic X Kitchen Island - Double [1]

Transcription

1 [1] Submitted by Ana White [2] on Mon, :10 [1] I'm so glad you all liked the plans for the Small Rustic X Kitchen Island [3] built by Shanty2Chic [4]! Page 1 of 23

2 Page 2 of 23

3 Thanks for all the encouraging feedback! I was so excited to see Bhoppy already built it too! [5] A few of you have requested the double sized island... so... plans follow! Enjoy! XO Ana Page 3 of 23

4 Summary: Free plans to build Rustic X Kitchen Island - double width - from Ana-White.com CategoriesProject Type: Kitchen Island Plans [6] Room: kitchen [7] Skill Level: Advanced [8] Style: Farmhouse Style Furniture Plans [9] Estimated Cost: $150 - $200 [10] Dimensions: Dimensions shown above Dimensions: /4" thick top 24" x 52" (recommend a premade project panel) 8 feet long 8 feet long 8 feet long (cut the 31 1/2" long pieces from this board) 4 feet long (cut the shelves from this board) Page 4 of 23

5 8 feet long 8 feet long 10 feet long 4 feet long 4' 1x10 board for the drawer stops 2-10"x18" 1/2" plywood pieces for drawer bottoms (can be scraps or purchase a 1/4" sheet) 4 caster wheels that can be mounted on bottom of 2x4 NOTE: Cut list and shopping list has been updated per reader comments on 9/18/2013 Common Materials: 2 inch screws 1 1/4 inch finish nails 2 inch finish nails 1-1/4" Pocket Hole Screws [11] 2-1/2" Pocket Hole Screws [12] Elmer's Wood Glue [13] Tools: Tape Measure [14] Speed Square [15] Carpenter's Pencil [16] Safety Glasses [17] Hearing Protection [18] Kreg Jig [19] Drill [20] Circular Saw [21] Compound Miter Saw [22] Brad Nailer [23] Power Sander [24] Cut List: degrees) degrees) 32 1/4" (legs) 19 1/2" (leg top/bottoms) 27 5/8" (long point to long point, both ends cut parallel at /4" (longest point measurement, one end cut at /2" (front bottom apron) 46 1/2" (middle bottom apron) 43 1/2" (top aprons/bottom of drawer trim) Page 5 of 23

6 7 1/2" (drawer center trim) 17 1/2" (shelf area center trim) 31 1/2" (shelf sides) 22 1/8" (drawer area backs) 14 1/4" (bottom shelf slats) 22 1/8" (shelves) 10 1/2" (drawer slides) 24" (top trim sides) 50 1/2" (top trim front/back) 1-3/4" thick top 24" x52" DRAWERS - measure and cut to fit so there's an 1/8" gap on each side!!! Measurements given should be used as a guide only. 11 1/4" (drawer sides) 17 3/8" (drawer front and back) 2-1/2" plywood 9 3/4" x 17 3/8" (drawer bottoms) 11 1/4" (drawer slide cleats) 20 3/4" (drawer faces) NOTE: Cut list and shopping list has been updated per reader comments on 9/18/2013 General Instructions: Please read through the entire plan and all comments before beginning this project. It is also advisable to review the Getting Started Section. Take all necessary precautions to build safely and smartly. Work on a clean level surface, free of imperfections or debris. Always use straight boards. Check for square after each step. Always predrill holes before attaching with screws. Use glue with finish nails for a stronger hold. Wipe excess glue off bare wood for stained projects, as dried glue will not take stain. Be safe, have fun, and ask for help if you need it. Good luck! Step 1 Page 6 of 23

7 [25] Start by building the two leg ends. Note that the outside and bottom are not flush. TIP: Drill 3/4" pocket holes on insides of top 2x4s for attaching top in later steps. Step 2 Page 7 of 23

8 [26] Attach the center Xs inside the leg/end apron frames. Remember to build two. Step 3 Page 8 of 23

9 [27] Next, attach the two leg sets together with the bottom 2x4s. Note that the bottom boards are at the same height as the bottom 2x4s in the leg sets - set up 3/4" from bottom of actual legs. Step 4 Page 9 of 23

10 [28] Attach the 2x2s to the top, leaving space between for the drawer. Also, I added a third 2x2 to the baci for extra support and to square things up now. Step 5 Page 10 of 23

11 [29] Position the center 2x2s in the front and attach. It's important that these guys - especially the top one - to be centered and square as the drawer faces will be wonky. Bottom may need to be cut to fit. Step 6 Page 11 of 23

12 [30] Attach the drawer/shelf sides. Make sure the center partition is exactly centered all the way down and across - otherwise your drawers will slide cockeyed. Step 7 Page 12 of 23

13 [31] Attach the back boards to finish out the back of the drawer area. Step 8 Page 13 of 23

14 [32] Attach shelf slats evenly spaced on bottom shelf area. Step 9 [33] Step 9 Instructions: Then attach shelves - these can be made fixed by attaching with 3/4" pocket holes and 1 1/4" pocket hole screws. They can also be adjustable if you use shelf pins. Step 10 Page 14 of 23

15 [34] There's a few different ways to do the drawers, but since they are so shallow (less than 12") it's hard to find small drawer slides. The 2x2s act as cleats to hold the drawer in the opening. Apply candle wax to top to make the drawer slide easier. Attach with just 2 2" screws for now - you may need to adjust to get the drawer to slide just right. Step 11 Build your drawers as shown above - but build to fit the opening. Measure between the 2x2s and subtract 1/4" (1/8" for each side) and make this the overall width of your drawer box (not including the 1x2 cleats) If you use pocket holes to build the drawer, place on outsides of front and back - they will get hidden by drawer face. Page 15 of 23

16 [35] Step 12 [36] Page 16 of 23

17 Adjust drawer until it slides easily. They should sit inset 3/4" to allow for the drawer face. Step 13 [37] With the drawers installed,cut the 1x8 drawer faces to fit the openings, leaving an 1/8" gap around all sides. Attach to drawer boxes with 1 1/4" finish nails and wood glue. Step 14 Page 17 of 23

18 [38] Frame out the top with 1x2s. These can be nailed and glued on. Step 15 Attach top through the 2x2s on the underside of the top and through predrilled pocket holes. You can also carefuly drill holes through the 1x2 trim into the underside of the top. Page 18 of 23

19 [39] Step 16 [40] Page 19 of 23

20 Attach caster wheels to base of legs. Finishing InstructionsPreparation Instructions: Fill all holes with wood filler and let dry. Apply additional coats of wood filler as needed. When wood filler is completely dry, sand the project in the direction of the wood grain with 120 grit sandpaper. Vacuum sanded project to remove sanding residue. Remove all sanding residue on work surfaces as well. Wipe project clean with damp cloth. It is always recommended to apply a test coat on a hidden area or scrap piece to ensure color evenness and adhesion. Use primer or wood conditioner as needed. Source URL: en-island-double Links [1] uble [2] [3] [4] ttery-barn.html [5] [6] [7] [8] [9] [10] [11] TF8&camp=1789&creative=390957&creativeASIN=B U2&linkCode=as2&tag=knooffwoo-20&linkId=5AJJ GUAWGYX2TT7E [12] TF8&camp=1789&creative=390957&creativeASIN=B00 0BN7DLU&linkCode=as2&tag=knooffwoo-20&linkId=XL DYGROR7GI4SHLA [13] [14] Page 20 of 23

21 dp/b00002x2ge/ref=as_li_ss_tl?s=hi&ie=utf8&qid= &sr=1-1&keywords=stanley+16+foot+tape+measure&a mp;linkcode=ll1&tag=knooffwoo20-20&linkid=eec222f82fbe 44887db4f333deeb210e&language=en_US [15] O/ref=as_li_ss_tl?s=hi&ie=UTF8&qid= &sr=1-3&keywords=speed+square&linkcode=ll1&t ag=knooffwoo20-20&linkid=320c4213eaaa27a0cf8de126c77f71ce &language=en_us [16] ece/dp/b0002ukq1g/ref=as_li_ss_tl?s=hi&ie=utf8&qid= &sr=1-5&keywords=carpenter+pencil&linkCod e=ll1&tag=knooffwoo20-20&linkid=7fac284ef4f952dfee44f0 673bcc5c3d&language=en_US [17] ef=as_li_ss_tl?ie=utf8&asins=b07253g22t&isrefresh=1&a mp;orderid= &purchaseid= &ref_=chk_typ_browserRefresh&viewId=ThankYouCart &linkcode=ll2&tag=knooffwoo20-20&linkid=874cc3bb cf86bcf48a5e97&language=en_US [18] pf_rd_m=atvpdkikx0der&pf_rd_s=hero-quick-promo&pf_rd_ r=7hrp6vn8hc2n89zkwezg&pf_rd_r=7hrp6vn8hc2n89zkwez G&pf_rd_t=201&pf_rd_p=d59dbb70-7ae6-48fe-a913-94e8957 9aec2&pf_rd_p=d59dbb70-7ae6-48fe-a913-94e89579aec2&p f_rd_i=b01fl5bqga&linkcode=ll1&tag=knooffwoo20-20&am p;linkid=fd59f542e0ed507f2b4af b52&language=en_us [19] L9BM/ref=as_li_ss_tl?s=power-hand-tools&ie=UTF8&qid= &sr=1-7&keywords=Kreg+Jig&linkCode=ll1&a mp;tag=knooffwoo20-20&linkid=a4db216a16a e090da2e0 ddeb7&language=en_us [20] dp/b005nnf0yu/ref=as_li_ss_tl?s=power-hand-tools&ie=utf8&am p;qid= &sr=1-3&keywords=drill&linkcode=ll 1&tag=knooffwoo20-20&linkId=9cbe53e8470db181dbb81d3 28a0a6175&language=en_US [21] p/b01bd81blo/ref=as_li_ss_tl?s=hi&ie=utf8&qid= &sr=1-7&keywords=circular+saw&linkCode=ll1&amp ;tag=knooffwoo20-20&linkid=ee95b8b5fb04316bf65bd f3 53&language=en_US Page 21 of 23

22 [22] r/dp/b01escu5ws/ref=as_li_ss_tl?s=local-services&ie=utf8& qid= &sr=8-1&keywords=miter+saw+sliding&am p;linkcode=ll1&tag=knooffwoo20-20&linkid=9239e e6e4bd4b4efc310be7&language=en_US [23] ss-battery/dp/b017nj6x7e/ref=as_li_ss_tl?s=hi&ie=utf8&qid = &sr=1-4&keywords=brad+nailer+cordless&am p;linkcode=ll1&tag=knooffwoo20-20&linkid=dcad8c839c75b c34e183d7&language=en_US [24] der/dp/b00mlss1sw/ref=as_li_ss_tl?s=hi&ie=utf8&qid= &sr=1-4&keywords=sander&linkCode=ll1&amp ;tag=knooffwoo20-20&linkid=888457a0a1042c e15b9d3 b50&language=en_us [25] [26] [27] [28] [29] [30] [31] [32] [33] [34] [35] [36] [37] [38] Page 22 of 23

23 [39] [40] Page 23 of 23