LINESSE LINEAR LUMINAIRE 3 CEILING MOUNT CM2420
|
|
- Chad Riley
- 5 years ago
- Views:
Transcription
1 Linesse Linear Luminaire 3 Ceiling Mount LINESSE LINEAR LUMINAIRE 3 CEILING MOUNT Page 2: Warnings Page 3: Mounting Configurations Page 4: Power Feed Page 5: Surface Mounting Page 6: Threaded Rod Mounting Page 7: Grid Mounting Page 8: Joining Fixtures Page 9: Corners 1
2 WARNING To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions, falling parts and other hazards: Installation and maintenance must be performed by a person familiar with the construction and operation of this product and any hazards involved. All applicable codes and ordinances must be followed Read this document before installing, servicing or maintaining this equipment. These instructions do not cover all installation, service and maintenance situations. If your situation is not covered, or, if you do not understand these instructions or additional information is required, contact your distributor Before installing, servicing or maintaining this equipment, follow these general precautions. To reduce the risk of electrocution: Make sure the equipment is properly grounded Always deenergize the circuit and/or equipment before connecting to, disconnecing from or servicing the equipment To prevent luminaire row from over-current: By adding the input current of each luminaire section marked on the luminaire, the total current per power feed must not exceed the maximum line wire amperage marked on the luminaire and the power feed cord/wire amperage rating whichever is the least To reduce the risk of fire: Use supply conductors with a minimum installation temperature rating as specified on equipment To reduce the risk of personal injury from cuts, abrasions or falling parts: Wear gloves to prevent cuts or abrasions from sharp edges when removing from carton, handling and maintaining this equipment Do not use abrasive materials, glass cleaners or other solvents on reflector or lens. These substances may damage equipment and cause parts to eventually break and fall Do not install a damaged fixture 2
3 TYPICAL MOUNTING CONFIGURATIONS Tee Grid Ceiling System Threaded Rod Mounting System IDS Clip with 1/4-20 Stud Conduit or J-Box (N/S) 1/2 Threaded Rod Direct to Surface Mounting System 3
4 INSTALLATION INSTRUCTIONS FOR POWER FEED Conduit or 2x4 Junction box Insert building power feed using conduit into the fixture feed hole or a 2x4 Junction box (supplied by others). Start with the first fixture and splice wiring according to the wiring diagram below. A starter harness must be used to connect to the through harness that will supply power to adjoining fixtures. Plug (supplied) any unused feed holes. Starter Harness Kit (ordered separately) Through Harness LINE WIRE COLOR BLK WHT RED GRN CIRCUIT DESCRIPTION CIRCUIT A HOT CIRCUIT A & B NEUTRAL CIRCUIT B HOT GROUNDING VLT DIMMING CONTROL 1 GRY DIMMING CONTROL 2 ORG WHT/ORG EHS or EHF HOT EHS or EHF NEUTRAL For special circuitry consult factory General Wiring Diagram LINE-IN FIXTURE 4
5 INSTALLATION INSTRUCTIONS FOR SURFACE MOUNTING Prepare Fixture for Mounting 1. Remove lens from fixture. 2. Remove reflector tray from fixture by removing screws and disconnecting LED board wiring plug (orange connector). Connect building power 1. Conduit to one of four connection holes or inside 2x4 J-Box on back of the fixture. ø.875(4) 2. Plug unused feed holes. Mount First Fixture to Ceiling 1. Start row with end of fixture without aligner brackets. 7 (178mm) 4 (102mm) 7 (178mm) 4 (102mm) 2. Secure fixture to surface with screws on both ends. Mounting hole pattern as shown (on right). Fixture is 3 lbs./h. Screws ø.22 Typical Splice building power wiring to starter harnesses (see wiring diagram) and connect starter harnesses to through harness for continuous row power. LINE-IN General Wiring Diagram FIXTURE Reassemble Fixture 1. Attach reflector tray to fixture by connecting the LED board wiring plug (orange connector). 2. Fasten Tray into fixture with tabs extending out on aligner end. Snap into place. Tabs 5
6 INSTALLATION INSTRUCTIONS FOR THREADED ROD MOUNTING Prepare Fixture for Mounting 1. Remove lens from fixture. 2. Remove reflector tray from fixture by removing screws and disconnecting LED board wiring plug (orange connector). Connect Building Power Conduit to one of four connection holes or inside 2x4 J-Box on back of the fixture. Plug unused feed holes. ø.875(4) Mount First Fixture to Rods 1. Start row with end of fixture without aligner brackets. Rod 6 (152mm) 6 (152mm) 2. Secure fixture to rod and nut on ends and inside Fasteners ø.63(2) Splice building power wiring to starter harnesses (see wiring diagram) and connect starter harnesses to through harness for continuous row power. LINE-IN General Wiring Diagram FIXTURE Conduit or 2x4 J-box Reassemble Fixture 1. Attach reflector tray to fixture by connecting the LED board wiring plug (orange connector). 2. Fasten tray into fixture with tabs extending out on aligner end. Tabs 3. Snap lens into place. 6
7 INSTALLATION INSTRUCTIONS FOR GRID MOUNTING Prepare Fixture for Mounting 1. Remove lens from fixture. 2. Remove reflector tray from fixture by removing screws and disconnecting LED board wiring plug (orange connector). Connect Building Power Conduit ø.875(4) 1. Connect to one of two non-centered connection holes on the back of the fixture. 2. Plug unused feed holes (plugs supplied). Mount First Fixture to IDS Clips 1. Start row with end of fixture without aligner brackets. IDS Clip 4 (102mm) 4 (102mm) 2. Secure fixture to IDS clips and fasten with supplied flange nut on both ends of fixture. Mounting hole pattern shown. ø.28(2) Splice building power wiring to starter harnesses (see wiring diagram) and connect starter harnesses to through harness for continuous row power. LINE-IN General Wiring Diagram FIXTURE Reassemble Fixture 1. Attach reflector tray to fixture by connecting the LED board wiring plug (orange connector). 2. Fasten tray into fixture with tabs extending out on aligner end. Tabs 3. Snap lens into place. 7
8 INSTALLATION INSTRUCTIONS FOR JOINING FIXTURES Joiner Bracket 1. Use joiner bracket and aligners located at the end of the fixture to align and connect fixtures. 2. Connect power harness connectors. 3. Slide mating fixture against first fixture. Slide 2nd Fixture 1. Fasten down the joiner bracket with (2) supplied screws. 2. After fixture is secured to ceiling, screw down reflector tray tabs in mating fixture (may not be on some fixtures). Joiner Bracket Screws Inside View Reflector Tab 1. Secure mating fixture to ceiling as instructed for starter fixture. 2. Assemble reflector tray in second fixture as instructed for starter fixture. Small 3. Insert small lens section centered where reflector trays meet. 4. Repeat Instructions for all joining fixtures (harnesses do not connect at new power location fixtures). At End of Row Locations 1. Remove joiner bracket, aligners, and reflector tray tabs. 2. Small lens is placed on the end of row to avoid light leak. 3. Tuck in end of harness. Small Joiner Bracket 4. Attach endcaps using supplied screws. 5. Attach final lens. Endcap Reflector Tabs 8
9 INSTALLATION INSTRUCTIONS FOR CORNERS Prepare Fixture for Mounting 1. Remove lens from fixture. 2. Remove Reflector Tray from fixture by removing screws and disconnecting LED board wiring plug (orange connector). Reflector Tray Connect Building Power Conduit 1. Connect to one of four conduit connection holes on the back of the fixture. 2. Plug unused feed holes (plugs supplied). Mount and Connect to Adjoining Fixture 1. Mount and connect fixture using linear row instructions. Mounting hole pattern shown. 2. Harness adapters are provided to make left or right corners. and joining bracket can be placed on either 3. Reconnect LED board wiring plugs and reassemble Reflector Tray. 4. Insert small lens section centered where Reflector Trays meet and in corner. 5. Attach harness to connecting fixture. 6. At end of row locations follow linear instructions for end cap placement. 6 (127mm) 5 (152mm) 1-1/8 (28mm) 18-5/8 (473mm) 23 (584mm) ø.22(8) #10 Screw ø.28(4) IDS Clip ø.63(4) 1/2 Thread Mounting ø.88(4) Conduit Connection 19-3/8 (492mm) 23 (584mm) Publication Rev: A June
EOS LED Surface Mounted Luminaire
Installation Instruction Sheet INSTALLATION INSTRUCTIONS FOR JOINING AND SUSPENDING FIXTURES WARNING WARNING To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions,
More informationLINESSE LINEAR LUMINAIRE 3 RECESSED CV2424
Linesse Linear Luminaire 3 Recessed LINESSE LINEAR LUMINAIRE 3 RECESSED Page 2: Warnings Page 3: Mounting Types and Dimensions Page 4: T-Grid and Joining Fixtures Page 5: Hard Ceiling and Joining Fixtures
More informationEOS Direct/Indirect LED Pendant Luminaire
Installation Instruction Sheet INSTALLATION INSTRUCTIONS FOR JOINING AND SUSPENDING FIXTURES WARNING WARNING To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions,
More informationEOS Linear LED Recessed Luminaires
Linear Recessed Fixtures WARNING WARNING INSTALLATION INSTRUCTIONS FOR MOUNTING RECESSED LINEAR FIXTURES To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions,
More informationLinear LED Recessed Luminaires
Installaon Instrucon Sheet Linear Recessed Fixtures INSTALLATION INSTRUCTIONS FOR MOUNTING RECESSED LINEAR FIXTURES WARNING WARNING To reduce the risk of death, injury or property damage from fire, electric
More informationGeneral Installation Instructions
General Installation Instructions WARNING To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions, falling parts and other hazards: Service of the equipment must
More informationSAVE THESE INSTALLATION INSTRUCTIONS
Light Without Boundaries LUMATO RESERVES THE RIGHT TO CHANGE PRODUCT 7500003 8/4 Light Without Boundaries LUMATO RESERVES THE RIGHT TO CHANGE PRODUCT GENERAL INSTALLATION WARNING To Reduce Risk Of Death,
More information-Always de-energize the circuit and/or equipment before connecting to, disconnecting from or servicing the equipment.
W3 Direct and W3 Indirect/Direct Series Products WARNING To Reduce Risk Of Death, Injury Or Property Damage From Fire, Electric Shock And Other Hazards: -Service of equipment must be performed by qualified
More informationHO4 Surface Mount Installation Instructions Overview
Overview Step 4 Mounting to Structure Pages 5-6 Step 5 Joining Luminaires Pages 7-8 Step 1 Mounting Types & Locations Page 2 Step 6 Closing Luminaires Page 9 Helpful Video 0-10V Dimming Step 2 Identification
More informationHP-2 / HP-4 / HP-6 Ceiling to Wall Inside Corner Installation Instructions Overview
Overview Step 4 Mounting to Structure Page 6 Step 1 Mounting Locations & Rough-Ins Pages 2-3 Step 2 Identification & Preparation Page 4 Step 6 Securing Corner Joints Page 8 Step 3 Opening Luminaires Page
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationLightplane 3.5 Recessed
INSTALLATION INSTRUCTIONS Lightplane 3.5 Recessed LP3.5R Recessed Ceiling IMPORTANT SAFETY INSTRUCTIONS When installing or using this fixtures basic safety precautions must be followed. Read all instructions
More informationINSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
FOR RECESSED EDGE-LIT LED EXIT SIGN Standard and New York Approved Models (Emergency, non-emergency and X2 Dual Circuit operation) READ AND FOLLOW ALL SAFETY INSTRUCTIONS IMPORTANT SAFEGUARDS: When using
More informationWARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE!
WARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE! General Safety Information To reduce the risk of death, personal injury or property damage from
More informationRAIL 4 PERIMETER RP4D RECESSED T-BAR LED TELESCOPIC, INTEGRAL DRIVER
INSTALLATION INSTRUCTIONS RAIL 4 PERIMETER RP4D RECESSED T-BAR LED TELESCOPIC, INTEGRAL DRIVER NOTE: The following instructions provide general guidelines for product installation. For additional information
More informationHP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions Overview
Overview NOTES All power connections should be installed according to local/national codes by a Certified Electrician. This installation requires proper support as each luminaire is being installed. DO
More informationHP-2 / HP-4 Wall Wash Recessed T-Bar Installation Instructions Overview
HP-2 / HP-4 Wash Recessed T-Bar Installation Instructions Overview NOTES All power connections should be installed according to local/national codes by a Certified Electrician. This installation requires
More informationRAIL 4 INSTALLATION INSTRUCTIONS. RM4DOD Recessed GENERAL SAFETY INSTRUCTIONS: NOTE:
INSTALLATION INSTRUCTIONS RAIL 4 RM4DOD Recessed NOTE: The following instructions provide general guidelines for product installation. For additional information consult the applicable electrical codes
More informationLIGHT FIXTURES MUST BE COMPLETELY INSTALLED PRIOR TO CEILING CONSTRUCTION
CAUTION: BEFORE BEGINNING INSTALLATION REVIEW LAYOUT DRAWINGS, AND SHIPMENT. MAKE SURE ALL LIGHT S AND MATERIALS ARE ON SITE AND READILY ACCESSIBLE. IF ANY ICON MATERIALS ARE MISSING, CONTACT ICON INTERNATIONAL
More informationMaxLite Linear Strip ECO Series
General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions
More information+ - 1a. 1b. c. 1d. 1e. Runway Suspended / Surface Cont. Run Installation. 2.0mm DIL DIL Revision - M 23/11/2018 Page 1
230-240V / 50-60Hz IP20 IK00 + - 2.0mm WARNING - THIS LUMINAIRE MUST BE EARTHED This luminaire has been tested and is manufactured to comply with BS EN 60598 : specification for general requirements and
More informationMESO X1 TBAR SEMI-RECESSED
MESO X1 TBAR SEMI-RECESSED 93t-inst PAGE 1 OF 2 1 2 A IMPORTANT Do not remove packaging around fixture until after fixture is installed. The packaging protects and in some cases supports the fixture during
More informationINSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE
T F W 604.549.979 604.549.9555 fluxwerx.com INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE fixture housing endcap kit optic kit join kit notch 2 cross section notch 4 cross section 4 4" 4-11/2" 4 /8 (111)
More informationTHIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2026 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationInstallation Instructions: T-Lite LED Signage Tube Lamps
Installation Instructions: T-Lite LED Signage Tube Lamps Installation Notes & Precautions: T-Lite LED Signage Tube Lamp Read all precautions, warnings, instructions contained in this document. These instructions
More informationP /8 Ring Diameter 90. Trim Ring Mounting Holes P /8. 393/16 Ring Diameter. Stud Minimum
PARTS LIST VARIABLE Top Over Head Support Bracket 1 872070 P4000-SMR Over Head Joiner Bracket 1 VARIABLE Bottom Over Head Bracket 1 79741 P4000-SMR 4 Angled Leg 4 100-00230-14 1/4-20 x 31/2 RD. HD. MS.
More informationINDIVIDUAL MOUNTING: T-Bar
X1 (T-BAR) INSTALLATION INSTRUCTIONS GENERAL NOTES NOTE : Additional support to structural member may be required. Check with local building codes for requirement. 1. Place troffer clamp approx. 6 from
More informationHealthcare LED TROFFER FLANGE (HSTLED Family)
Healthcare LED TROFFER FLANGE (HSTLED Family) Applies to all HSTLED production after 6/1/2015 (reference CI-Code *231V2F and later) Revision 04 I-HSTLED-FLANGE Revision Date 6/11/2015 Healthcare Lighting
More informationMultiples EM_ 1.4. Install 1X1/1X2/1X3/1X4 Housings. Installation Instructions for. This product is suitable for indoor locations.
Installation Instructions for 90EMULTI Multiples EM_. GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer or a 0-0V
More informationINSTALLATION INSTRUCTIONS
Sheet 1 of 5 General: Upon receipt of fixture thoroughly inspect for any freight damage, which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the
More informationGLASS GLOBE MOBILE LINEAR CHANDELIER
PARTS ENCLOSED: (B) Top ceiling plate [1] (C) Bottom ceiling plate [1] (D) Glass globes [7] (E) Screws [6] (F) Nuts [5] (G) Extension rods [15] (H) Transformer [1] (I) Threaded inserts [5] (J) 1.6W LED
More informationINSTALLATION INSTRUCTIONS FIXTURE SERIES: SAE 202 MOUNTING TYPE: RECESSED WALL / SLOT PAGE: 1 OF 8
INSTALLATION INSTRUCTIONS FIXTURE SERIES: SAE 202 MOUNTING TYPE: RECESSED WALL / SLOT PAGE: 1 OF 8 90v INNER CORNER KIT "R" (REGRESSED) POSITION CROSS-SECTION VIEW "S" (SHIELDING AT TOP) POSITION CROSS-SECTION
More informationSeriesTWO RGB Fluorescent Fixtures. Installation and Instruction Manual
SeriesTWO RGB Fluorescent Fixtures Installation and Instruction Manual Brightline LP 580 Mayer Street #7, Bridgeville PA 15017 Phone 1-412-206-0106 Fax 1-412-206-0146 www.brightlines.com The Brightline
More informationLED RETROFIT INSTALLATION
QUICK INSTRUCTIONS 1 2 3 4 5 6 Once the original fixture components have been removed to satisfy rebate requirements the Raffino LR Series retrofit kit is ready to be instal. At a minimum the original
More informationDOWNLIGHT LED SERIES INSTALLATION INSTRUCTIONS
WARNING: This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Make sure all
More informationSTEP 1 - CEILING PREPARATION
STEP 1 - PREPARATION 1/4-20 THREADED RODS SR FIXTURE SLOT/ IN SHEET ROCK WHIP A) MAKE SLOT IN SHEET ROCK ACCORDING TO RUN INFORMATION, TYPE OF FIXTURE AND REFER TO S REQUIRED (FIGURE 2 - SR* AND FIGURE
More informationBionic 4 PERIMETER, CONTINUOUS RUN X3, X7
I NSTALLAT ION INSTRUC TIONS 6 3 /4 6 3 /4 3¾ 5 1 /2 For LP installs, ceiling opening is equal to row length + 3 /4 8 1 /2 4 3 /32 5 1 /4 Flush X7 Shown PARTS SHIPPED SEPARATELY 4 3 /32 5 1 /4 3" Regressed
More informationZIP CLOUD SUSPENDED INSTALLATION MANUAL
ZIP CLOUD SUSPENDED INSTALLATION MANUAL www.delviro.com info@delviro.com 1.877.502.3434 SAFETY NOTE: Follow the Electrical Codes of the Country where this fixture will be installed. For Canada follow the
More informationINSTALLATION INSTRUCTIONS Xenix Incandescent Series XN12, XN24, XN36, XN48
INSTALLATION INSTRUCTIONS Xenix Incandescent Series XN12, XN24, XN36, XN48 IMPORTANT SAFETY INSTRUCTIONS ---- CAUTION! --- READ THIS FIRST 11500 Melrose Avenue Franklin Park, Illinois 60131 Phone: 847-451-0700
More informationRound or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E3_L_-L_DI 1.4
Installation Instructions for 90ELED-DIC Round or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E_L_-L_DI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More informationEXPLODED VIEW AND PART CALL OUT ASSEMBLING THE METALUX DF SERIES FRAME KIT
EXPLODED VIEW AND PART CALL OUT CUTOUT DIMENSIONS ON PAGE 2 CEILING BRACING (BY OTHERS) SHEET ROCK METALUX DF SERIES FRAME KIT S282 (2'X2') FIXTURE SHOWN FIXTURE SIZE FRAME KIT PART # 2' X 2' DF-22W-U
More informationArched Top Lantern Pendant Assembly and Installation Instructions. Country of Destination: US/CN UK/EU/AUS Middle East
CAUTION: Arched Top Lantern Pendant Assembly and Installation Instructions Country of Destination: US/CN UK/EU/AUS Middle East BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF
More informationADAPT. ABILITY. X 6.50" Example of a continuous row. Shown: hanging the fixture via threaded rods.
AMELUX Suspension Points 6.50" GUV4-HE-FLANGE; GUV6-HE-FLANGE Gyp Board Ceiling INSTALLATION INSTUCTIONS SHEET #: 689-0498 SHEET 1 of 9 (SHEETS 1-4) T5/T5HO (SHEET 5) T5/T5HO LUXOTTICA (SHEETS 6-9) LED
More informationJoiner Kit Joiner bracket (x1) Biscuit aligners (x2) Trim Flange
- Trim System Overview These instructions review how to install TruGroove Perimeter fixtures. Modules can be installed as individual standalone units, or they can be joined together to create continuous
More information5 ACCESS PANEL INSTALLATION SPACER *SLIDE TO LOCATION OF FASTENER DURING INSTALLATION OF EACH FASTENER
1/2 K.O. (3/8 K.O. on 165 with factory supplied 3/8 flex conduit fitting) TR - Trim Flange Side Blocking Install Method Secure fixture to structure following instructions below: 1. Remove lens and internal
More informationQuadroMAX. Installation Manual. QM Series. LED Outdoor Lighting Fixtures REV: 3/22/16
QuadroMAX LED Outdoor Lighting Fixtures Installation Manual QM Series REV: 3/22/16 BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING Risk of fire or electric shock. Luminaire wiring
More informationSAE of 7 "R" (REGRESSED) POSITION "S" (SHIELDING AT TOP) POSITION. Tools Required
SAE 0 5/6'' Exposed TBar Ceiling FINISHED EDGE WITH JANGLE 90 IC CORNER KIT 5 7/6" 38mm 9/6'' Screw Slot TBar Ceiling "R" (REGRESSED) POSITION 6" CEILING OPENING "S" (SHIELDING AT TOP) POSITION SUPPORT
More informationInde-Pendants Family. 32L Surface Mount Cylinder with Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder with Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-CRxx-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants:
More informationBLUEMOTION UXP, CDP, SD
Feed and Support Kit Contents FEED KIT CONTENTS: - One () 7 Feed Cord - One () 4 Canopy - One () Grommet - One () Threaded Barrel - One () 7 Swedged Suspension Cable - One () Y-Cable Assembly with Cable
More informationRound or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims
Installation Instructions for 90ELED-WIC Round or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims LED E_L_-L_WI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More informationNemalux INSTALLATION INSTRUCTIONS APPLICATION 1-4
I N D U S T R I A L rev. A- INSTALLATION INSTRUCTIONS *PENDING* E77827 E77827 APPLICATION MR3 & MR6 Luminaires are suitable for use in the following areas as defined by the National Electrical Code (NEC)
More informationPow-R-Feed Systems Service Manual
Pow-R-Feed Systems Service Manual Important Safety Instructions Please read this manual carefully and follow its instructions. Improper use or failure to follow these instructions could result in serious
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More informationMADELINE METAL CHANDELIER
MADELINE METAL CHANDELIER Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationSenior Swing. Caution
*740132* 740132 2800 Overhead Concealed Series 9500 Surface Applied Series Senior Swing Installation Instructions Caution LCN Senior Swing The Senior Swing Power Operator System is a low energy product
More informationInstall the Housing. Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing EN3_-LH9_ 1.
Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing 90ENTRA EN_-LH9_. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is safety
More informationRound or Square Chicago Plenum Down Light Housing with Lamp
Installation Instructions for 90ELED-DCP Round or Square Chicago Plenum Down Light Housing with Lamp LED E_-L_DC. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations.
More informationInigo Sconce INSTALLATION INSTRUCTIONS P _2_A 1 of 5
P31321 1 of 5 Thank You For Choosing Kallista We appreciate your commitment to Kallista quality products. Please take a moment to review this manual before you install your Kallista product. If you encounter
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationMicro Channel. Shorten the Fixture (optional) Installation Instructions for 700UMCD_ UNILUME. This product is suitable for damp locations.
Installation Instructions for Micro Channel 700UMCD_ 90MICRO. UNILUME GENERAL PRODUCT I NFORMATION: This product is suitable for damp locations. This product can be dimmed with a low-voltage electronic
More informationSUPERPLANE TM 4 RECESSED SP4R
Oakland, INSTALLATION INSTRUCTIONS SUPERPLANE TM RECESSED SPR TGrid ATZ Slot n A 1035 22nd Avenue, Unit 1 CA 606 P 510.8.2530 E TalkToUs@alwusa.com W alwusa.com SPR - Safety & Warnings! 1. Read all instructions.
More informationIMPORTANT: WILL NOT FIT COUNTRYMAN MODELS
Part #1410-0102-07 2 3 1 IMPORTANT: WILL NOT FIT COUNTRYMAN MODELS Apply masking tape around the bottom grille opening and across the bottom of the upper facto ry grille.. Open the hood and remove the
More informationWARNING. Failure to observe these instructions could lead to severe injury or death.
INSTALLATION INSTRUCTIONS WINCH MOUNTING KIT Part Number: 80156, 80160 Application: 2008 Ford F150 Your safety, and the safety of others, is very important. To help you make informed decisions about safety,
More informationInde-Pendants Family. 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-C-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants: Cylinder (Surface
More informationGEN II Toyota Prius Back Door Opener Switch Replacement & License Plate Lights
GEN II Toyota Prius Back Door Opener Switch Replacement & License Plate Lights Rubber Surface of Switch had Degraded to Tar-like Substance Vehicle Manufacture Date 10/06 OLD SWITCH IN GARNISH SWITCH REMOVED
More informationVersatility at Work. Installation Instructions
Versatility at Work Installation Instructions Important Things to know Use the screws, provided in each box, to attach Eliminator Track TM to the ceiling grid Understand the Basic Cut. You will use this
More informationNash Chandelier Assembly and Installation Instructions
CAUTION: Nash Chandelier Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. Important
More informationConnecting the Channel A
20 Edge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension T, Tubular Lens w/2sq or 2RD Canopy IMPORTANT INFORMATION - This product is suitable for indoor locations.
More informationDAWN TO DUSK SENSOR OWNER S MANUAL
DAWN TO DUSK SENSOR OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More information- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS. Factory pre-installed mud flange TOOLS REQUIRED: Phillips screwdriver, 5/16 nut driver.
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install drywall trim versions of TruGroove recessed
More informationModular & Hardwired Hub Assembly to "X" and "Y" Posts
Modular & Hardwired Hub Assembly to "X" and "Y" Posts Hardware Package T-Nut Data jack bracket #6 x 1/4" plastite trilobular screw 1/4-20 x 3/4" socket head cap screw #6-32 x 1/4" pan head screw #10-32
More informationF5513 APOGEE 30"DIA 3LTS PENDANT INSTALLATION INSTRUCTIONS WARNING
F5513 APOGEE 30"DIA 3LTS PENDANT INSTALLATION INSTRUCTIONS TROY LIGHTING DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION. CAUTION
More informationM MODULAR PARTS T01-A INSTALLATION INSTRUCTIONS MIRRORED CABINET SIMPLIFIED LEFT OPENING DOOR K-15512T-NL RIGHT OPENING DOOR K-15512T-NR
M M MODULAR INSTALLATION INSTRUCTIONS ( ) MIRRORED CABINET SIMPLIFIED LEFT OPENING DOOR K-1551T-NL RIGHT OPENING DOOR K-1551T-NR BEFORE YOU BEGIN Please read these instructions carefully to familiarize
More information18600 PORTABLE POWER DRIVE THREADER PRODUCT INFORMATION AND OPERATING INSTRUCTIONS:
WIDDER TOOLS 18600 PORTABLE POWER DRIVE THREADER PRODUCT INFORMATION AND OPERATING INSTRUCTIONS: Description: The 18600 Portable Electric Threader is an electric-motor-driven, heavy-duty power drive which
More information18500 PORTABLE ELECTRIC POWER DRIVE
18500 PORTABLE ELECTRIC POWER DRIVE PRODUCT INFORMATION AND OPERATING INSTRUCTIONS: Description: Widder 18500 Portable Electric Power Drive is an electric-motor-driven, heavy-duty power drive which provides
More informationM MODULAR PARTS T01-A INSTALLATION INSTRUCTIONS MIRRORED CABINET W/DEFOGGER K-15512T , 2011 Copyright Kohler China Ltd.
M M MODULAR INSTALLATION INSTRUCTIONS ( ) MIRRORED CABINET W/DEFOGGER K-15512T BEFORE YOU BEGIN Please read these instructions carefully to familiarize yourself with the required tools, materials, and
More informationSUPERPLANE 2.5 INSTALLATION INSTRUCTIONS WALL/SURFACE BACK MOUNT. A nd Avenue, Unit 1 Oakland,
INSTALLATION INSTRUCTIONS SUPERPLANE 2.5 WALL/SURFACE BACK MOUNT A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com SP2.5 - Safety & Warnings! 1. Read all instructions.
More informationAliante Installation. Components included: Tools required: Not Included:
041137c 1 08.25.16 Important Notes: Please read entire guide before beginning fixture installation. For installation by a qualified electrician familiar with the construction and operation of luminaire
More informationBL-ER-P Ethernet Radio Unit for Pedestal Installation Guide
Assemble the Antenna Riser 1. Remove the antenna riser assembly and the antenna from its packaging. 2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna. 3. Put the stem
More informationSECURITY DOORS - 2', 3', 4'
INTRODUCTION: CAREFULLY READ THE CONTENTS OF THESE INSTRUCTIONS, AS THEY INDICATE THE CORRECT STEP BY STEP PROCEDURE TO ASSEMBLE THE PRODUCT. THE CARTON CONTENTS PAGE(S) WILL IDENTIFY THE ASSEMBLY PARTS.
More informationC 0.05" ALLEN WRENCH. Installation Instructions for Cirrus Channel Suspension T1 with 4" Square or Round Canopy. Section One: Adjusting Cable Position
Doc # 90-CST-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension
More informationPlease read BOTH these Installation Instructions and the General Instructions prior to installing or operating this equipment.
Attachment Tab Height: 19-1/2 Attachment Tab Width: 19 Serial Number Please read BOTH these and the General Instructions prior to installing or operating this equipment. 1. Blue Ox towing products and
More information*** All chrome surfaces should be cleaned using a clean damp cloth. *** No abrasive cleaning agents or materials should be used.
Cleaning *** All chrome surfaces should be cleaned using a clean damp cloth. *** No abrasive cleaning agents or materials should be used. *** No chemical cleaners can be used on the glass use only mild
More informationContinuous Handrail Kit Installation Instructions
Continuous Handrail Kit Installation Instructions ALUMINUM RAILING SYSTEM Canadian Version Wall Application (see page 2) Railing Application (see page 7) Wall anchors not provided Hardware included: 1x
More informationCable Tray Kit: - Cable Tray - Cable Tray Cover - Power Block Support (x2) Top Support Kit: (x2) - 2 Top Supports. Quantities are per bench
Parts Included (per back to back bench) Column Kit: (x2) - 1 LH & 1 RH Column - Control Box - Hand Switch Cable Tray Kit: - Cable Tray - Cable Tray Cover - Power Block Support (x2) Depth Support Kit: -
More informationInstallation Guide 888-4WB TRAY
Installation Guide WBT has pioneered the innovation of cabletray/basket tray in the last decade. Products such as Shaped Tray, PreForm, WBTForm and NoSplice have allowed users and installers to provide
More informationINSTALLATION INSTRUCTIONS SUPERPLANE 4 WALL MOUNT. A nd Avenue, Unit 1 Oakland, CA P E W alwusa.
INSTALLATION INSTRUCTIONS SUPERPLANE 4 WALL MOUNT A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com SP4 - Safety & Warnings! 1. Read all instructions. 2. Install
More informationMirage Installation Manual
Mirage Installation Manual General Information This installation manual provides necessary information for the safe installation of the Mirage product. WARNING: Failure to follow the instructions in this
More informationA524 ASSEMBLY & INSTALLATION INSTRUCTIONS BELLADONNA PENDANT CASTLETON, VERMONT USA SYNCHRONICITYLIGHTING.COM Rev A 1 OF 7
1 OF 7 COMPONENT PARTS A B Canopy Mounting Bracket C Anchor (4) D #10 Wood Screw (4) E F G H Safety Cable Ground Screw Cupped Washer Safety Cable screw I Gripper (2) J Barrel Knob (4) K L Lightbar Fixture
More informationInstallation Instructions For TruLine 1.6A 24VDC
2014 Pure Lighting. All Rights Reserved. Installation Instructions For TruLine 1.6A 24VDC INS# 902-TL1.6A-07 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 773-770-1195 Fax: 773-935-5613 www.purelighting.com
More informationHP-4 Wall Wash Recessed Flush Diffuser Visible Flange Starter/Independent Installation Instructions
HP-4 Wall Wash Recessed Flush Visible Flange /Independent Installation Instructions Scan QR code for helpful video(s) 0-10V Dimming Step 1 a ( Cutout Dimension Step 2 S Step 3 1/-20 Threaded Rod 1/-20
More informationPOLYBAG KIT JOINER STRAP FIXTURE TYPE ROLL OF DOUBLE SIDED TAPE REQUIRED FOR R/POSITION WALL ANGLES (SEE STEP 6) 12"LG U-ANGLE (3) U-CLIPS
STRAIGHT EXTENSION [SE] P/C PG. OF NOTES: STRAIGHT EXTENSIONS (SE) ARE INSTALLED AT ENDS OF ROW TO CLOSE OFF CEILING OPENING. A. FIXTURES MUST BE INSTALLED PRIOR TO ATTACHING STRAIGHT EXTENSIONS. B. STRAIGHT
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2006 2007 Honda Ridgeline THE safety accessory of the 21 st Century. P/N 210 0142 0 Rev. A (9/5/07), BTV 2007 Muth Company, LLC Professional Installation Recommended:
More informationVIT SB-16SS Pedestal. Conversion Guide
Converting a to Baseline This guide describes the steps for removing another manufacturer s irrigation controller from a VIT SB-16SS pedestal and installing a Baseline controller. Remove All Parts of the
More informationINSTALLATION RECOMMENDATIONS For The Con-Tech ODYSSEY Line Voltage Flexible Track System
INSTALLATION RECOMMENDATIONS For The Con-Tech ODYSSEY Line Voltage Flexible Track System IMPORTANT SAFETY INSTRUCTIONS: Read all instructions before installation. Save these instructions for later use.
More informationREGOLO GENERAL WARNING
REGOLO GENERAL WARNING WARNING: DO NOT ASSEMBLE CONTINUOUS RUN ON THE GROUND AND LIFT INTO PLACE. JOINTS WILL DISTORT AND NOT CREATE A TIGHT FIT. JOINING HARDWARE WILL HAVE TO BE PURCHASED AND REPLACED.
More informationETC Installation Guide
ETC Installation Guide Unison Using this Guide This document is intended to guide you through the installation of the DRd Semi-Recessed installation kit. Reference the Unison DRd Rack Enclosure Installation
More informationInstallation Instructions Standalone or continuous run configurations - 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install trimless drywall versions of TruGroove
More informationInstallation and Operation Manual. Ajustable Valance Kits CAUTION: Duke Manufacturing Co.
Installation and Operation Manual Ajustable Valance Kits 2502757 2502857 : Please read this manual completely before attempting to install, operate or service this equipment This manual is Copyright 2018
More informationHP-2 Recessed Wall Wash Flush Diffuser Tech Zone 4" Starter/Independent Installation Instructions
HP-2 Recessed Wall Wash Flush Tech Zone /Independent Scan QR code for helpful video(s) Step 1 Step 2 Tech Zone Collection. Center-to-center spacing Wall 0-10V Dimming.0.0.0 Tech Zone (C1) Tech Zone (C2)
More information