EOS Direct/Indirect LED Pendant Luminaire
|
|
- Beverley French
- 5 years ago
- Views:
Transcription
1 Installation Instruction Sheet INSTALLATION INSTRUCTIONS FOR JOINING AND SUSPENDING FIXTURES WARNING WARNING To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions, falling parts and other hazards: Service of the equipment must be performed by qualified service personnel. Installation and maintenance must be performed by a person familiar with the construction and operation of this product and any hazards involved. All applicable codes and ordinances must be followed. Read this document before installing, servicing or maintaining this equipment. These instructions do not cover all installation, service and maintenance situations. If your situation is not covered, or, if you do not understand these instructions or additional information is required, contact Lux Illuminaire or your local agent. Read and follow all warnings and instructions provided by the LED manufacturer. Before installing, servicing or maintaining this equipment, follow these general precautions. To reduce the risk of electrocution: Make sure the equipment is properly grounded. Always de-energize the circuit and/or equipment before connecting to, disconnecting from or servicing the equipment. To prevent luminaire row from over-current: By adding the input current of each luminaire section marked on the luminaire, the total current per power feed must not exceed the maximum line wire amperage marked on the luminaire and the power feed cord/wire amperage rating whichever is the least. To reduce the risk of fire: Keep material away that can burn from hot LEDs. Make sure LED boards are correctly installed. Use supply conductors with a minimum installation temperature rating as specified on equipment. To reduce the risk of personal injury from cuts, abrasions or falling parts: Wear gloves to prevent cuts or abrasions from sharp edges when removing from carton, handling and maintaining this equipment. Do not use abrasive materials, glass cleaners or other solvents on reflector or lens. These substances may damage equipment and cause parts to eventually break and fall. Do not install a damaged fixture.
2 Typical Mounting Configurations Drop Ceiling System (Non Feed) Drop Ceiling System (Feed) Hard Ceiling System (Non Feed) Hard Ceiling System (Feed)
3 Typical Mounting Configurations Hard Ceiling System (Non Feed) Hard Ceiling System (Feed) Junction box (by others) Junction box (by others) Stem Strap Stem Nuts Stem Strap Stem Nuts Fixture Wires Stem Strap Screws Fixture Wires Canopy Screws Canopy Canopy Screws Canopy Stem Stem Stem Joiner Fixture harness plugs Attach through harness connectors. Stem feed Power from Stem DIM
4 Installation Instruction Sheet INSTALLATION INSTRUCTIONS FOR POWER FEED CORD Power feed cord Insert power cord through feed hole on the first fixture and plug to through harness connectors. Plug (supplied) any unused feed holes. Power DIM For special circuitry consult factory POWER FEED CORD COLOR LINE WIRE COLOR CIRCUIT DESCRIPTION 14x3 BLK/WHT/GRN CIRCUIT A & EMERGENCY BLK CIRCUIT A HOT 14x4 BLK/WHT/GRN/RED CIRCUIT B, OR CIRCUIT A W/ EHS WHT RED CIRCUIT A & B NEUTRAL CIRCUIT B HOT 18x5 BLK/WHT/GRN/VLT/GRY CIRCUIT A & EMERGENCY & DIM GRN GROUNDING VLT DIMMING CONTROL 1 GRY DIMMING CONTROL 2 ORG WHT/ORG EHS or EHF HOT EHS or EHF NEUTRAL General Wiring Diagram LINE-IN FIXTURE GRN - GND GRN - GND WHT-NEU WHT-NEU BLK- HOT BLK- HOT VLT-DIM + VLT-DIM + GRY-DIM - GRY-DIM -
5 INSTALLATION INSTRUCTIONS FOR JOINING AND SUSPENDING CABLE MOUNTED FIXTURES Use hanger bracket located at the end of the fixture to support fixture. Cable Gripper Cable Gripper Screw cable gripper into the outside thread position of hanger at the end of a row OR in the middle thread position if joining fixtures together. Adjust fixture length from ceiling with cable gripper. (End of Row position) (joining Fixture position) Use provided flathead screws to secure hanger bracket to fixture. Attach power and dimming harness connectors from the fixture to the power cord in power locations. (Tuck in fixture) (Attach to Power Cord) Power feed connectors Guides are used to align fixtures. Slide fixtures together and fasten supplied flathead screw to bracket. For row mounting fixtures attach male end of harness to female end of harness and slide fixtures together. Small lens section is centered between fixtures to avoid light leak at lens ends. Fasten flathead screws on each fixture. (Connect harnesses) Guides Fasten reflector tabs down with supplied screws to the joining fixture. Lens Reflector Tab (2) (Screw down when connected) Remove Direct side of fixture to install Endcaps Tuck in harness at the end of rows and attach endcaps using supplied screws. Fold reflector tabs up or break off at the end of rows. Re-attach fixture lens. Screw holes
6 INSTALLATION INSTRUCTIONS FOR JOINING AND SUSPENDING STEM MOUNTED FIXTURES Replace cable hanger brackets with stem brackets supplied in the hardware kit for mounting stem fixture. Nut on both sides Insert stem into the outside hole position of the hanger at the beginning or the end of a row. Insert stem into the middle hole position of the hanger where joining fixtures together. (End of Row position) (joining Fixture position) Use provided flathead screws to secure hanger bracket to fixture. Attach power and dimming harness connectors from the fixture to the power cord in power locations. (Tuck in fixture) (Attach to Feed harness) Power feed connectors Guides are used to align fixtures. Slide fixtures together and fasten supplied flathead screw to bracket. Guides For row mounting fixtures attach male end of harness to female end of harness and slide fixtures together. Small lens section is centered between fixtures to avoid light leak at lens ends. Fasten flathead screws on each fixture. Fasten reflector tabs down with supplied screws to the joining fixture. Note: Endcap installation can be seen With cable mounting instructions. Lens (Connect harnesses) Reflector Tab (2) (Screw down when connected)
EOS LED Surface Mounted Luminaire
Installation Instruction Sheet INSTALLATION INSTRUCTIONS FOR JOINING AND SUSPENDING FIXTURES WARNING WARNING To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions,
More informationLINESSE LINEAR LUMINAIRE 3 CEILING MOUNT CM2420
Linesse Linear Luminaire 3 Ceiling Mount LINESSE LINEAR LUMINAIRE 3 CEILING MOUNT Page 2: Warnings Page 3: Mounting Configurations Page 4: Power Feed Page 5: Surface Mounting Page 6: Threaded Rod Mounting
More informationLINESSE LINEAR LUMINAIRE 3 RECESSED CV2424
Linesse Linear Luminaire 3 Recessed LINESSE LINEAR LUMINAIRE 3 RECESSED Page 2: Warnings Page 3: Mounting Types and Dimensions Page 4: T-Grid and Joining Fixtures Page 5: Hard Ceiling and Joining Fixtures
More informationEOS Linear LED Recessed Luminaires
Linear Recessed Fixtures WARNING WARNING INSTALLATION INSTRUCTIONS FOR MOUNTING RECESSED LINEAR FIXTURES To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions,
More informationLinear LED Recessed Luminaires
Installaon Instrucon Sheet Linear Recessed Fixtures INSTALLATION INSTRUCTIONS FOR MOUNTING RECESSED LINEAR FIXTURES WARNING WARNING To reduce the risk of death, injury or property damage from fire, electric
More informationGeneral Installation Instructions
General Installation Instructions WARNING To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions, falling parts and other hazards: Service of the equipment must
More informationSAVE THESE INSTALLATION INSTRUCTIONS
Light Without Boundaries LUMATO RESERVES THE RIGHT TO CHANGE PRODUCT 7500003 8/4 Light Without Boundaries LUMATO RESERVES THE RIGHT TO CHANGE PRODUCT GENERAL INSTALLATION WARNING To Reduce Risk Of Death,
More information-Always de-energize the circuit and/or equipment before connecting to, disconnecting from or servicing the equipment.
W3 Direct and W3 Indirect/Direct Series Products WARNING To Reduce Risk Of Death, Injury Or Property Damage From Fire, Electric Shock And Other Hazards: -Service of equipment must be performed by qualified
More informationINSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS
FOR RECESSED EDGE-LIT LED EXIT SIGN Standard and New York Approved Models (Emergency, non-emergency and X2 Dual Circuit operation) READ AND FOLLOW ALL SAFETY INSTRUCTIONS IMPORTANT SAFEGUARDS: When using
More informationZIP CLOUD SUSPENDED INSTALLATION MANUAL
ZIP CLOUD SUSPENDED INSTALLATION MANUAL www.delviro.com info@delviro.com 1.877.502.3434 SAFETY NOTE: Follow the Electrical Codes of the Country where this fixture will be installed. For Canada follow the
More informationWARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE!
WARNINGS & SAFETY INFORMATION: PLEASE READ CAREFULLY AND KEEP A COPY ON THE PROPERTY FOR FUTURE REFERENCE! General Safety Information To reduce the risk of death, personal injury or property damage from
More informationRAIL 4 PERIMETER RP4D RECESSED T-BAR LED TELESCOPIC, INTEGRAL DRIVER
INSTALLATION INSTRUCTIONS RAIL 4 PERIMETER RP4D RECESSED T-BAR LED TELESCOPIC, INTEGRAL DRIVER NOTE: The following instructions provide general guidelines for product installation. For additional information
More informationGeneral Installation Instructions LED
General Installation Instructions LED To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards, please read all warnings
More informationLED RETROFIT INSTALLATION
QUICK INSTRUCTIONS 1 2 3 4 5 6 Once the original fixture components have been removed to satisfy rebate requirements the Raffino LR Series retrofit kit is ready to be instal. At a minimum the original
More informationMaxLite Linear Strip ECO Series
General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions
More informationF5513 APOGEE 30"DIA 3LTS PENDANT INSTALLATION INSTRUCTIONS WARNING
F5513 APOGEE 30"DIA 3LTS PENDANT INSTALLATION INSTRUCTIONS TROY LIGHTING DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION. CAUTION
More informationLightplane 3.5 Recessed
INSTALLATION INSTRUCTIONS Lightplane 3.5 Recessed LP3.5R Recessed Ceiling IMPORTANT SAFETY INSTRUCTIONS When installing or using this fixtures basic safety precautions must be followed. Read all instructions
More informationMADELINE METAL CHANDELIER
MADELINE METAL CHANDELIER Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationBLUEMOTION UXP, CDP, SD
Feed and Support Kit Contents FEED KIT CONTENTS: - One () 7 Feed Cord - One () 4 Canopy - One () Grommet - One () Threaded Barrel - One () 7 Swedged Suspension Cable - One () Y-Cable Assembly with Cable
More informationArched Top Lantern Pendant Assembly and Installation Instructions. Country of Destination: US/CN UK/EU/AUS Middle East
CAUTION: Arched Top Lantern Pendant Assembly and Installation Instructions Country of Destination: US/CN UK/EU/AUS Middle East BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF
More informationTHIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2026 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationHO4 Surface Mount Installation Instructions Overview
Overview Step 4 Mounting to Structure Pages 5-6 Step 5 Joining Luminaires Pages 7-8 Step 1 Mounting Types & Locations Page 2 Step 6 Closing Luminaires Page 9 Helpful Video 0-10V Dimming Step 2 Identification
More informationGLASS GLOBE MOBILE LINEAR CHANDELIER
PARTS ENCLOSED: (B) Top ceiling plate [1] (C) Bottom ceiling plate [1] (D) Glass globes [7] (E) Screws [6] (F) Nuts [5] (G) Extension rods [15] (H) Transformer [1] (I) Threaded inserts [5] (J) 1.6W LED
More informationC 0.05" ALLEN WRENCH. Installation Instructions for Cirrus Channel Suspension T1 with 4" Square or Round Canopy. Section One: Adjusting Cable Position
Doc # 90-CST-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension
More informationInde-Pendants Family. 32L Surface Mount Cylinder with Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder with Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-CRxx-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants:
More informationINSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE
T F W 604.549.979 604.549.9555 fluxwerx.com INSTALLATION: D1-NOTCH DRYWALL TRIM FLANGE fixture housing endcap kit optic kit join kit notch 2 cross section notch 4 cross section 4 4" 4-11/2" 4 /8 (111)
More informationNash Chandelier Assembly and Installation Instructions
CAUTION: Nash Chandelier Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. Important
More informationConnecting the Channel A
20 Edge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension T, Tubular Lens w/2sq or 2RD Canopy IMPORTANT INFORMATION - This product is suitable for indoor locations.
More informationSeriesTWO RGB Fluorescent Fixtures. Installation and Instruction Manual
SeriesTWO RGB Fluorescent Fixtures Installation and Instruction Manual Brightline LP 580 Mayer Street #7, Bridgeville PA 15017 Phone 1-412-206-0106 Fax 1-412-206-0146 www.brightlines.com The Brightline
More informationROPE CHANDELIER - FRAME ASSEMBLY & INSTALLATION INSTRUCTIONS
ROPE CHANDELIER - FRAME ASSEMBLY & INSTALLATION INSTRUCTIONS CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. IMPORTANT
More informationCustom Pendant- Hardwire Assembly and Installation Instructions
Custom Pendant- Hardwire Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationRAIL 4 INSTALLATION INSTRUCTIONS. RM4DOD Recessed GENERAL SAFETY INSTRUCTIONS: NOTE:
INSTALLATION INSTRUCTIONS RAIL 4 RM4DOD Recessed NOTE: The following instructions provide general guidelines for product installation. For additional information consult the applicable electrical codes
More informationHealthcare LED TROFFER FLANGE (HSTLED Family)
Healthcare LED TROFFER FLANGE (HSTLED Family) Applies to all HSTLED production after 6/1/2015 (reference CI-Code *231V2F and later) Revision 04 I-HSTLED-FLANGE Revision Date 6/11/2015 Healthcare Lighting
More informationHP-2 / HP-4 / HP-6 Ceiling to Wall Inside Corner Installation Instructions Overview
Overview Step 4 Mounting to Structure Page 6 Step 1 Mounting Locations & Rough-Ins Pages 2-3 Step 2 Identification & Preparation Page 4 Step 6 Securing Corner Joints Page 8 Step 3 Opening Luminaires Page
More informationA524 ASSEMBLY & INSTALLATION INSTRUCTIONS BELLADONNA PENDANT CASTLETON, VERMONT USA SYNCHRONICITYLIGHTING.COM Rev A 1 OF 7
1 OF 7 COMPONENT PARTS A B Canopy Mounting Bracket C Anchor (4) D #10 Wood Screw (4) E F G H Safety Cable Ground Screw Cupped Washer Safety Cable screw I Gripper (2) J Barrel Knob (4) K L Lightbar Fixture
More informationHP-2 / HP-4 Wall Wash Recessed T-Bar Installation Instructions Overview
HP-2 / HP-4 Wash Recessed T-Bar Installation Instructions Overview NOTES All power connections should be installed according to local/national codes by a Certified Electrician. This installation requires
More informationInstallation Instructions for Cirrus Suspension Downlight with Power - End Feed. Section One: 4" Flush Canopy Version
Doc # 0-CSP-E_0 W. Fullerton Chicago, IL 606 Ph:.0. Fax:..6 www.pureedgelighting.com info@pureedgelighting.com 06 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Suspension
More informationLIGHT FIXTURES MUST BE COMPLETELY INSTALLED PRIOR TO CEILING CONSTRUCTION
CAUTION: BEFORE BEGINNING INSTALLATION REVIEW LAYOUT DRAWINGS, AND SHIPMENT. MAKE SURE ALL LIGHT S AND MATERIALS ARE ON SITE AND READILY ACCESSIBLE. IF ANY ICON MATERIALS ARE MISSING, CONTACT ICON INTERNATIONAL
More informationLED Gas Station Light Installation Guide
Product Applications: WISDOM LED Gas Station Lighting series can be widely used in indoor or outdoor lighting NOTE: New refers to mounting to a new/ replaced canopy skin. Definition: Replacement refers
More informationINSTALLATION INSTRUCTIONS Xenix Incandescent Series XN12, XN24, XN36, XN48
INSTALLATION INSTRUCTIONS Xenix Incandescent Series XN12, XN24, XN36, XN48 IMPORTANT SAFETY INSTRUCTIONS ---- CAUTION! --- READ THIS FIRST 11500 Melrose Avenue Franklin Park, Illinois 60131 Phone: 847-451-0700
More informationInstallation Instructions for Zip Suspension Downlight with Remote Power and 4" Square or Round Canopy
Doc # 90-ZS-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Zip Suspension Downlight
More informationHP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions Overview
Overview NOTES All power connections should be installed according to local/national codes by a Certified Electrician. This installation requires proper support as each luminaire is being installed. DO
More informationRound or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E3_L_-L_DI 1.4
Installation Instructions for 90ELED-DIC Round or Square Type IC Down Light Housing with LED Lamp for Flangeless Trims E_L_-L_DI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More informationFabric tiered drum pendant 30in Assembly and Installation Instructions
CAUTION: Fabric tiered drum pendant 30in Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY
More informationInde-Pendants Family. 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-C-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants: Cylinder (Surface
More informationRound or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims
Installation Instructions for 90ELED-WIC Round or Square Type IC Wall Wash Housing with Lamp for Flangeless Trims LED E_L_-L_WI. LED - ROUND/ SQUARE FLANGELESS GENERAL PRODUCT I NFORMATION: This product
More informationInde-Pendants Family. 32L Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No Installation instructions for 32L-Rxx-P
Inde-Pendants Family 32L Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-Rxx-P Document No. Supplied by Litecontrol 32L Inde-Pendants: Ring (Plaster Trim, Grid and Drywall
More informationJoiner Kit Joiner bracket (x1) Biscuit aligners (x2) Trim Flange
- Trim System Overview These instructions review how to install TruGroove Perimeter fixtures. Modules can be installed as individual standalone units, or they can be joined together to create continuous
More informationQuadroMAX. Installation Manual. QM Series. LED Outdoor Lighting Fixtures REV: 3/22/16
QuadroMAX LED Outdoor Lighting Fixtures Installation Manual QM Series REV: 3/22/16 BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING Risk of fire or electric shock. Luminaire wiring
More information+ - 1a. 1b. c. 1d. 1e. Runway Suspended / Surface Cont. Run Installation. 2.0mm DIL DIL Revision - M 23/11/2018 Page 1
230-240V / 50-60Hz IP20 IK00 + - 2.0mm WARNING - THIS LUMINAIRE MUST BE EARTHED This luminaire has been tested and is manufactured to comply with BS EN 60598 : specification for general requirements and
More informationIMPORTANT SAFETY INSTRUCTIONS:
Online: www.ballarddesigns.com PRODUCT NAME: MR Geometric Chandelier ITEM NUMBER: LC971 DIMENSIONS OF ITEM ASSEMBLED: FLUSH- 36 H x 42 W x 30 1/2 D HANGING- 96 H x 42 W x 30 1/2 D HANGING FIXTURE: FLUSH
More informationINSTALLATION INSTRUCTIONS
Sheet 1 of 5 General: Upon receipt of fixture thoroughly inspect for any freight damage, which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the
More informationBionic 4 PERIMETER, CONTINUOUS RUN X3, X7
I NSTALLAT ION INSTRUC TIONS 6 3 /4 6 3 /4 3¾ 5 1 /2 For LP installs, ceiling opening is equal to row length + 3 /4 8 1 /2 4 3 /32 5 1 /4 Flush X7 Shown PARTS SHIPPED SEPARATELY 4 3 /32 5 1 /4 3" Regressed
More informationRound or Square Chicago Plenum Down Light Housing with Lamp
Installation Instructions for 90ELED-DCP Round or Square Chicago Plenum Down Light Housing with Lamp LED E_-L_DC. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations.
More information- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS. Factory pre-installed mud flange TOOLS REQUIRED: Phillips screwdriver, 5/16 nut driver.
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install drywall trim versions of TruGroove recessed
More informationMESO X1 TBAR SEMI-RECESSED
MESO X1 TBAR SEMI-RECESSED 93t-inst PAGE 1 OF 2 1 2 A IMPORTANT Do not remove packaging around fixture until after fixture is installed. The packaging protects and in some cases supports the fixture during
More informationDOWNLIGHT LED SERIES INSTALLATION INSTRUCTIONS
WARNING: This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved. Make sure all
More informationCAUTION: BEFORE INSTALLING THE LUMINAIRE, MAKE SURE THAT THE CURRENT IS CUT TO THE BOX FUSES / MAIN CIRCUIT BREAKER.
Hanging lamp with horn Assembly and installation instructions CAUTION: BEFORE INSTALLING THE LUMINAIRE, MAKE SURE THAT THE CURRENT IS CUT TO THE BOX FUSES / MAIN CIRCUIT BREAKER. Important safety instructions:
More informationWoven Leather Chandelier Large Assembly and Installation Instructions
CAUTION: Woven Leather Chandelier Large Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY
More informationBL-ER-P Ethernet Radio Unit for Pedestal Installation Guide
Assemble the Antenna Riser 1. Remove the antenna riser assembly and the antenna from its packaging. 2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna. 3. Put the stem
More informationMultiples EM_ 1.4. Install 1X1/1X2/1X3/1X4 Housings. Installation Instructions for. This product is suitable for indoor locations.
Installation Instructions for 90EMULTI Multiples EM_. GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer or a 0-0V
More informationMasterFlow Green Machine Dual Powered Roof Vent
MasterFlow Green Machine Dual Powered Roof Vent Application Instructions Updated: 2/10 Quality You Can Trust Since 1886... From North America s Largest Roofing Manufacturer Safety Considerations and Warnings
More informationInigo Sconce INSTALLATION INSTRUCTIONS P _2_A 1 of 5
P31321 1 of 5 Thank You For Choosing Kallista We appreciate your commitment to Kallista quality products. Please take a moment to review this manual before you install your Kallista product. If you encounter
More informationRiverside. Windward Bay EntertaInment Wall System Assembly Instructions. Made In Viet Nam. Right Pier. Bridge & Back Panel.
EntertaInment Wall System Page 1 of 12 Product No. 42840 42848 42849 42843 Product Description Console Left Pier Right Pier Bridge & Back Panel Right Pier Bridge & Back Panel Left Pier 63" Inch Ent. Console
More informationMODULAR LED UNDERCABINET LIGHTING SYSTEM Max 540watts IMPORTANT SAFETY INSTRUCTIONS
MODULAR LED UNDERCABINET LIGHTING SYSTEM Max 540watts IMPORTANT SAFETY INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS GENERAL 1. To insure the success of the
More informationInstallation Instructions Standalone or continuous run configurations - 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install trimless drywall versions of TruGroove
More informationModel 4210-MMPC-L. Multi-measurement Prober Cable Kit. Overview. Quick start guide topics. Related documents
Model 0-MMPC-L Keithley Instruments, Inc. Multi-measurement Prober Cable Kit 877 Aurora Road Quick Start Guide Cleveland, Ohio 9-888-KEITHLEY http://www.keithley.com Overview The Keithley Instruments Model
More informationNemalux INSTALLATION INSTRUCTIONS APPLICATION 1-4
I N D U S T R I A L rev. A- INSTALLATION INSTRUCTIONS *PENDING* E77827 E77827 APPLICATION MR3 & MR6 Luminaires are suitable for use in the following areas as defined by the National Electrical Code (NEC)
More informationAssembly & Installation Instructions
1 OF 6 Component Parts A B C Fixture Mounting Bracket Canopy D Threaded Standoffs (2) E Cap (2) F Anchors (4) G #10 Screws (4) H I J K Safety Cable #8 Screw Ground Screw Cupped Washer Socket Assembly (6)
More informationB235 Mobius Sconce Page 1 of 6
Mobius Sconce 28-9450 Page 1 of 6 CAUTION: FAILURE TO INSTALL THIS PRODUCT PROPERLY MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. We recommend installation by a qualified individual trained in the
More informationINSTALLATION RECOMMENDATIONS For The Con-Tech ODYSSEY Line Voltage Flexible Track System
INSTALLATION RECOMMENDATIONS For The Con-Tech ODYSSEY Line Voltage Flexible Track System IMPORTANT SAFETY INSTRUCTIONS: Read all instructions before installation. Save these instructions for later use.
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More informationCABLE MOUNTED FOR INDIVIDUAL FIXTURES OR CONTINUOUSLY ROW MOUNTED
AMELUX Pre-installation Note: Supplied by others: - 4" octagonal junction boxes LIN3.5D LED (SHEETS 1-4) LS35D T5/T5HO (SHEETS 5-6 ) CABLE MOUNTED FO INDIVIDUAL FIXTUES O CONTINUOUSLY OW MOUNTED SHEET
More informationDAWN TO DUSK SENSOR OWNER S MANUAL
DAWN TO DUSK SENSOR OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
More informationCisco Outdoor Omnidirectional Antenna for 2G/3G/4G Cellular (ANT-4G-OMNI-OUT-N)
CHAPTER 4 Cisco Outdoor Omnidirectional Antenna for 2G/3G/4G Cellular (ANT-4G-OMNI-OUT-N) The Cisco Outdoor Omnidirectional Antenna for 2G/3G/4G Cellular antenna is designed to cover domestic LTE700/Cellular/PCS/AWS/MDS,
More informationDISCONNECT POWER PRIOR TO ANY INSTALLATION.
ALL MODELS: THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. CE PRODUIT
More informationRSS Rectilinear Suspended Series
Catalog # : Project : Prepared By : Date : RSS The RSS Rectilinear Suspended luminaire adds a truly unique, seamless and sophisticated look to any project requiring an easy to install, upscale lighting
More informationPage 1 T O O L S A N D M AT E R I A L S R E Q U I R E D. 1. Screwdriver 2. Carpenter's level 3. Electrical Tape PA R T S L I S T. A.
T O O L S A N D M AT E R I A L S R E Q U I R E D 1. Screwdriver 2. Carpenter's level 3. Electrical Tape PA R T S L I S T A. Cabinet B. Wood Screw X4 C. Plastic wire connector x3 Page 1 I M P O R TA N T
More informationKANEKA OLED Lighting Module SL (LE-01L, LE-02L, LE-03L, LE-01H, LE-02H, LE-03H) Instruction Manual
KANEKA OLED Lighting Module SL (LE-01L, LE-02L, LE-03L, LE-01H, LE-02H, LE-03H) Instruction Manual Safety Information p. 2 1 Product Overview p. 6 2 Connections and Wiring (when dimming is required) p.
More informationGLASS GLOBE MOBILE 6-ARM CHANDELIER
PARTS ENCLOSED: (B) Top ceiling plate [1] (C) Bottom ceiling plate [1] (D) Glass globes [6] (E) Screws [4] (F) Nut [1] (G) Extension rods [3] (H) Transformer [1] (I) Arm counterweights [6] (J) 1.6W LED
More informationVIT SB-16SS Pedestal. Conversion Guide
Converting a to Baseline This guide describes the steps for removing another manufacturer s irrigation controller from a VIT SB-16SS pedestal and installing a Baseline controller. Remove All Parts of the
More informationAliante Installation. Components included: Tools required: Not Included:
041137c 1 08.25.16 Important Notes: Please read entire guide before beginning fixture installation. For installation by a qualified electrician familiar with the construction and operation of luminaire
More informationInstallation Instructions
007A00 ROOFTOP UNITS GAS HEATING/ELECTRIC COOLING ACCESSORY FLUE DISCHARGE DEFLECTOR SELECT 7.5---10, 12---1/2 and 15 TON Installation Instructions TABLE OF CONTENTS PACKAGE CONTENTS... 1 SAFETY CONSIDERATIONS...
More informationInstruction page index: Installation Instructions for Kilo S Models KILOS-CF & KILOS-SF. Page 1 of 5. Center Feed installation Side Feed installation
Installation Instructions for Kilo S Models KILOS-CF & KILOS-SF Page 1 of 5 Instruction page index: Center Feed installation Side Feed installation 2-3 4-5 Kilo S - Instruction for center feed installation
More informationModular & Hardwired Hub Assembly to "X" and "Y" Posts
Modular & Hardwired Hub Assembly to "X" and "Y" Posts Hardware Package T-Nut Data jack bracket #6 x 1/4" plastite trilobular screw 1/4-20 x 3/4" socket head cap screw #6-32 x 1/4" pan head screw #10-32
More informationPow-R-Feed Systems Service Manual
Pow-R-Feed Systems Service Manual Important Safety Instructions Please read this manual carefully and follow its instructions. Improper use or failure to follow these instructions could result in serious
More informationInstallation Instructions: T-Lite LED Signage Tube Lamps
Installation Instructions: T-Lite LED Signage Tube Lamps Installation Notes & Precautions: T-Lite LED Signage Tube Lamp Read all precautions, warnings, instructions contained in this document. These instructions
More informationRM4000 Tektronix 4000 Series Rackmount Kit
Instructions RM4000 Tektronix 4000 Series Rackmount Kit 071-2134-01 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationBOLLARD INSTALLATION INSTRUCTIONS
ROUND BOLLARD IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. RAB fixtures must be wired in accordance with the National Electrical Code and all applicable
More informationELECTRIC RANGE INSTALLATION MANUAL. Please read these instructions thoroughly before installing and operating the range.
ENGLISH ESPAÑOL INSTALLATION MANUAL ELECTRIC RANGE Please read these instructions thoroughly before installing and operating the range. MODELS LRE30955S LRE30755S LRE30757S LSE3094S LSE3092S LSRE307ST
More informationMEC Auto-Mate Assembly Manual. For MEC 9000G/GN and 8567 Grabber Series
MEC Auto-Mate Assembly Manual For MEC 9000G/GN and 8567 Grabber Series Thank you We really appreciate your support of our product line. But our commitment to you hardly ends here. We won't be satisfied
More informationIMPORTANT SAFETY INSTRUCTIONS: -We strongly recommend that a professional electrician install all direct wire fixtures.
PRODUCT NAME: Mimi Quatrefoil Ceiling Mount ITEM NUMBER: LM199 BRA 1016 DIMENSIONS OF ITEM ASSEMBLED: 10 1/2 H x 15 1/2 DIA IMPORTANT SAFETY INSTRUCTIONS: -We strongly recommend that a professional electrician
More informationFOLDING ARM AWNING FITTING INSTRUCTIONS
FOLDING ARM AWNING FITTING INSTRUCTIONS (INCLUDING OPTIONAL UPGRADE RAFTER BRACKET FIXING) Your new Outdoor Awning has been custom built for you from the highest quality materials please follow the installation
More informationHOLLY HUNT LIGHTING. STUDIO H EDGE CHANDELIER Installation Instructions
NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. J-BOX & CEILING CANOPY MOUNTING PLATE TEMPORARY CHAINS LABELED CABLE & CORD
More informationZHONGSHAN KOHLER SHOWER CO., LTD. NO13-1, XINGYE ROAD, ZHONGSHAN TORCH DEVELOPMENT ZONE, ZHONGSHAN, GUANGDONG, CHINA POST CODE:
NEW VERDERA INSTALLATION INSTRUCTIONS MIRRORED CABINET K-78202T-L/K-78202T-R/K-78282T BEFORE YOU BEGIN Please read these instructions carefully to familiarize yourself with the required tools, materials,
More information1?4" SHEET METAL SCREW APERTURE GAUGE. Housing Aligner Spline HOUSING ALIGNER SPLINE PANHEAD SCREW. #10 x.1875 SMS. Aligner/ Seam Joiner
HOUSING ALIGNER SPL P33 INSTALLATION DRAWINGS X3 (HARD CEILING) PARTS (SHIPPED SEPARATELY) 8/32 x 1/2 PHD S.T. SCREW REMOVAL TOOL TROFFER CLAMP 1/4 Sheet Metal Screw Housing Aligner Spline HOUSING ALIGN
More informationHERCULES EXTENDED TOWER
AmeriGlide Accessibility Solutions HERCULES EXTENDED TOWER ATION GUIDE Please read this installation guide carefully to ensure correct installation of the HERCULES EXTENDED TOWER Vertical Platform Lift.
More informationINSTALLATION INSTRUCTIONS SUPERPLANE 4 WALL MOUNT. A nd Avenue, Unit 1 Oakland, CA P E W alwusa.
INSTALLATION INSTRUCTIONS SUPERPLANE 4 WALL MOUNT A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com SP4 - Safety & Warnings! 1. Read all instructions. 2. Install
More informationKIT PART NUMBER VE5880 INSTRUCTIONS FOR INSTALLING REGENERATION UCB IN NATIONAL 147AND 148 MACHINES.
KIT PART NUMBER VE5880 INSTRUCTIONS FOR INSTALLING REGENERATION UCB IN NATIONAL 147AND 148 MACHINES. COMPARE THE PARTS RECEIVED IN THIS KIT WITH THE PARTS LIST IN THE INSTRUCTIONS. IF ANY PARTS ARE MISSING
More information