HOLLY HUNT LIGHTING. STUDIO H EDGE CHANDELIER Installation Instructions
|
|
- Jane Tate
- 5 years ago
- Views:
Transcription
1 NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. J-BOX & CEILING CANOPY MOUNTING PLATE TEMPORARY CHAINS LABELED CABLE & CORD HOLES CANOPY w/ MOUNTED POWER SUPPLIES AND WIRES. (FIXTURES VARY, NOT ALL ARE SHOWN) ELEC. CORD STRAIN RELIEF SUSPENSION CABLES UPPER DIFFUSER CABLE ADJUSTERS NOTE: DO NOT OVERTIGHTEN SCREWS LIGHT BAR LOWER DIFFUSER 8-32 x 3/16" CONE POINT SET SCREW
2 NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. CONTENTS (1) Rectangular Canopy 36" L x 18" W (1) Canopy Mouting Frame (3) Light Bar, Electrical Cord and pre-installed Strain Relief with Set Screw (3) Lower Acrylic Diffuser (3) Upper Acrylic Diffuser (6) Suspension Cables, Labeled and pre-marked with insertion depth (4) Canopy Mounting Screws (#10-32) (4) Temporary Chains w/ S-Hooks (3) Hex Wrench 1/16, 5/64, 1/8 (4) Sets of Gloves to be worn during installation. NOTE: DO NOT OVERTIGHTEN SCREWS UL Approved in US and Canada
3 PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. INSTRUCTIONS 1. Determine fixture location, J Box should be located on the center of the Fixture. 2. Screw Canopy Mounting Plate to ceiling w/ appropriate screws and/or anchors per installation requirements. (Mounting requirements and hardware to be determined and provided by installer) 3. Hang Temporary Chains from Canopy Mounting Plate; raise Canopy to hang from Temporary Chains, note alignment mark on Canopy Mounting Plate and Canopy. NOTE: TEMPORARY CHAINS ARE NOT MEANT TO BE LEFT SUSPENDING THE FIXTURE FOR EXTENDED PERIODS OF TIME 4. Connect Volt power to pre-wired fixture (black and white wires). All power supplies have been installed by manufacturer. The drivers installed in this unit have multiple methods of dimming to accommodate your needs. The systems are capable of Triac dimming at 120 VAC or have the option for 0-10 vdc current-sinking control for dimming. 5. Make Electrical connections to fixture based on dimming type or controls with provided wiring diagrams supplied with dimming or control options. (See next page for diagrams.) This fixture can be wired to accept Triac dimming or 0-10V dimming or switch (the 0-10V dimming signal must be supplied to the purple and gray wires as there is no reference voltage supplied from the driver for this dimming option)). If no dimming is required cap gray and purple wires from the driver and install a nondimming switch wired per switch instructions. 6. Slide the labeled Suspension Cables into corresponding holes through top of Canopy. 7. Match the Light Bars to their corresponding labels in the Canopy and hang all Light Bars from the Suspension Cables with Cable Adjusters to the insertion depth marked on the Cables. 8. Loosen Set Screws pre-installed in Strain Reliefs with provided Hex Wrench. 9. Uncoil silver cloth covered Elec. Cord and feed through Strain Reliefs. Snug the set screw in the Strain Relief against the Cord when the Cord is hanging straight---do NOT OVERTIGHTEN. 10. Make electrical connections with Snap Connectors at labeled positions in Canopy. Connect to Supply Power with wire nuts and Ground to Canopy. 11. Remove pre-installed 8-32 x 3/16" Cone Point Set Screws from ends of Light Bars using provided Hex Wrench. Reaise each numbered Lower Diffuser to the corresponding Light Bar and secure into bottom slot by re-installing Cone Point Set Screws. DO NOT OVERTIGHTEN SCREWS. 12. Install Upper Diffusers into Light Bars. 13. Remove Temporary Chains and raise the Canopy to the Canopy Mounting Plate. Secure with provided screws (start all screws before final tightening). 14. Based on site conditions, a slight leveling of Light Bars may be necessary. Pressing the center cylinder of the Cable Adjuster will release pressure on the Cable and Light Bar can be repositioned.
4 HOLLY HUNT STUDIO NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. 0-10V Dimmer Switch Ref. Control Module Light Bar Below Light Bar Below REFERENCE WIRING DIAGRAM FOR 0-10V DIMMING To 120/240V J-Box Wire Nut Light Bar Below Light Bar Below REFERENCE WIRING DIAGRAM WITHOUT DIMMING REFERENCE TRIAC WIRING DIAGRAM Triac Dimmer Wire Nut Light Bar Below Light Bar Below
5 NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. J-BOX & CEILING CANOPY MOUNTING PLATE TEMPORARY CHAINS LABELED CABLE & CORD HOLES CANOPY w/ MOUNTED POWER SUPPLIES AND WIRES. (FIXTURES VARY, NOT ALL ARE SHOWN) ELEC. CORD STRAIN RELIEF SUSPENSION CABLES UPPER DIFFUSER CABLE ADJUSTERS NOTE: DO NOT OVERTIGHTEN SCREWS LIGHT BAR LOWER DIFFUSER 8-32 x 3/16" CONE POINT SET SCREW
6 CONTENTS (1) Rectangular Canopy 72" L x 18" W (1) Canopy Mouting Frame (5) Light Bar, Electrical Cord (5) Strain Reliefs with Nylon Tip Set Screw Installed (5) Lower Acrylic Diffuser (5) Upper Acrylic Diffuser (10) Suspension Cables, Labeled and pre-marked with insertion depth (6) Canopy Mounting Screws (#10-32) (4) Temporary Chains w/ S-Hooks (3) Hex Wrench 1/8", 1/16" and 5/64" (4) Sets of Gloves to be worn during installation. (2) Extra Butt Connector (2) 8-32 x 3/16 or 1/4 Cone Point SS, Pre-installed per Light Bar (5) Wire Nuts NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. NOTE: DO NOT OVERTIGHTEN SCREWS UL Approved in US and Canada
7 PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. INSTRUCTIONS 1. Determine fixture location, J Box should be located on the center of the Fixture. 2. Screw Canopy Mounting Plate to ceiling w/ appropriate screws and/or anchors per installation requirements. (Mounting requirements and hardware to be determined and provided by installer) 3. Hang Temporary Chains from Canopy Mounting Plate; raise Canopy to hang from Temporary Chains, note alignment mark on Canopy Mounting Plate and Canopy. NOTE: TEMPORARY CHAINS ARE NOT MEANT TO BE LEFT SUSPENDING THE FIXTURE FOR EXTENDED PERIODS OF TIME 4. Connect Volt power to pre-wired fixture (black and white wires). All power supplies have been installed by manufacturer. The drivers installed in this unit have multiple methods of dimming to accommodate your needs. The systems are capable of Triac dimming at 120 VAC or have the option for 0-10 vdc current-sinking control for dimming. 5. Make Electrical connections to fixture based on dimming type or controls with provided wiring diagrams supplied with dimming or control options. (See next page for diagrams.) This fixture can be wired to accept Triac dimming or 0-10V dimming or switch (the 0-10V dimming signal must be supplied to the purple and gray wires as there is no reference voltage supplied from the driver for this dimming option)). If no dimming is required cap gray and purple wires from the driver and install a nondimming switch wired per switch instructions. 6. Slide the labeled Suspension Cables into corresponding holes through top of Canopy. 7. Match the Light Bars to their corresponding labels in the Canopy and hang all Light Bars from the Suspension Cables with Cable Adjusters to the insertion depth marked on the Cables. 8. Loosen Set Screws pre-installed in Strain Reliefs with provided Hex Wrench. 9. Uncoil silver cloth covered Elec. Cord and feed through Strain Reliefs. Snug the set screw in the Strain Relief against the Cord when the Cord is hanging straight---do NOT OVERTIGHTEN. 10. Make electrical connections with Snap Connectors at labeled positions in Canopy. Connect to Supply Power with wire nuts and Ground to Canopy. 11. Remove pre-installed 8-32 x 3/16" Cone Point Set Screws from ends of Light Bars using provided Hex Wrench. Reaise each numbered Lower Diffuser to the corresponding Light Bar and secure into bottom slot by re-installing Cone Point Set Screws. DO NOT OVERTIGHTEN SCREWS. 12. Install Upper Diffusers into Light Bars. 13. Remove Temporary Chains and raise the Canopy to the Canopy Mounting Plate. Secure with provided screws (start all screws before final tightening). 14. Based on site conditions, a slight leveling of Light Bars may be necessary. Pressing the center cylinder of the Cable Adjuster will release pressure on the Cable and Light Bar can be repositioned.
8 HOLLY HUNT STUDIO NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. 0-10V Dimmer Switch Ref. Control Module Light Bar Below Light Bar Below REFERENCE WIRING DIAGRAM FOR 0-10V DIMMING To 120/240V J-Box Wire Nut Light Bar Below Light Bar Below REFERENCE WIRING DIAGRAM WITHOUT DIMMING REFERENCE TRIAC WIRING DIAGRAM Triac Dimmer Wire Nut Light Bar Below Light Bar Below
9 NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. J-BOX & CEILING CANOPY MOUNTING PLATE TEMPORARY CHAINS LABELED CABLE & CORD HOLES CANOPY w/ MOUNTED POWER SUPPLIES AND WIRES. (FIXTURES VARY, NOT ALL ARE SHOWN) ELEC. CORD STRAIN RELIEF SUSPENSION CABLES UPPER DIFFUSER CABLE ADJUSTERS NOTE: DO NOT OVERTIGHTEN SCREWS LIGHT BAR LOWER DIFFUSER CONE POINT SET SCREW
10 NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. CONTENTS (1) Rectangular Canopy 108" L x 18" W (1) Canopy Mouting Frame (7) Light Bar, Electrical Cord and pre-installed Strain Relief with Set Screw (7) Lower Acrylic Diffuser (7) Upper Acrylic Diffuser (14) Suspension Cables, Labeled and pre-marked with insertion depth (10) Canopy Mounting Screws (#10-32) (4) Temporary Chains w/ S-Hooks (1) Hex Wrench (4) Sets of Gloves to be worn during installation. NOTE: DO NOT OVERTIGHTEN SCREWS UL Approved in US and Canada
11 PLEASE USE THE FOLLOWING DIAGRAM AND STEPS FOR INSTALLATION NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. INSTRUCTIONS 1. Determine fixture location, J Box should be located on the center of the Fixture. 2. Screw Canopy Mounting Plate to ceiling w/ appropriate screws and/or anchors per installation requirements. (Mounting requirements and hardware to be determined and provided by installer) 3. Hang Temporary Chains from Canopy Mounting Plate; raise Canopy to hang from Temporary Chains, note alignment mark on Canopy Mounting Plate and Canopy. NOTE: TEMPORARY CHAINS ARE NOT MEANT TO BE LEFT SUSPENDING THE FIXTURE FOR EXTENDED PERIODS OF TIME 4. Connect Volt power to pre-wired fixture (black and white wires). All power supplies have been installed by manufacturer. The drivers installed in this unit have multiple methods of dimming to accommodate your needs. The systems are capable of Triac dimming at 120 VAC or have the option for 0-10 vdc current-sinking control for dimming. 5. Make Electrical connections to fixture based on dimming type or controls with provided wiring diagrams supplied with dimming or control options. (See next page for diagrams.) This fixture can be wired to accept Triac dimming or 0-10V dimming or switch (the 0-10V dimming signal must be supplied to the purple and gray wires as there is no reference voltage supplied from the driver for this dimming option)). If no dimming is required cap gray and purple wires from the driver and install a nondimming switch wired per switch instructions. 6. Slide the labeled Suspension Cables into corresponding holes through top of Canopy. 7. Match the Light Bars to their corresponding labels in the Canopy and hang all Light Bars from the Suspension Cables with Cable Adjusters to the insertion depth marked on the Cables. 8. Loosen Set Screws pre-installed in Strain Reliefs with provided Hex Wrench. 9. Uncoil silver cloth covered Elec. Cord and feed through Strain Reliefs. Snug the set screw in the Strain Relief against the Cord when the Cord is hanging straight---do NOT OVERTIGHTEN. 10. Make electrical connections with Snap Connectors at labeled positions in Canopy. Connect to Supply Power with wire nuts and Ground to Canopy. 11. Remove pre-installed 8-32 x 3/16" Cone Point Set Screws from ends of Light Bars using provided Hex Wrench. Reaise each numbered Lower Diffuser to the corresponding Light Bar and secure into bottom slot by re-installing Cone Point Set Screws. DO NOT OVERTIGHTEN SCREWS. 12. Install Upper Diffusers into Light Bars. 13. Remove Temporary Chains and raise the Canopy to the Canopy Mounting Plate. Secure with provided screws (start all screws before final tightening). 14. Based on site conditions, a slight leveling of Light Bars may be necessary. Pressing the center cylinder of the Cable Adjuster will release pressure on the Cable and Light Bar can be repositioned.
12 HOLLY HUNT STUDIO NOTE: CLEAN GLOVES MUST BE WORN DURING INSTALLATION. DO NOT REMOVE PAPER FROM ACRYLIC DIFFUSER UNTIL INSTALLATION IS COMPLETE. 0-10V Dimmer Switch Ref. Control Module Light Bar Below Light Bar Below REFERENCE WIRING DIAGRAM FOR 0-10V DIMMING To 120/240V J-Box Wire Nut Light Bar Below Light Bar Below REFERENCE WIRING DIAGRAM WITHOUT DIMMING REFERENCE TRIAC WIRING DIAGRAM Triac Dimmer Wire Nut Light Bar Below Light Bar Below
BLUEMOTION UXP, CDP, SD
Feed and Support Kit Contents FEED KIT CONTENTS: - One () 7 Feed Cord - One () 4 Canopy - One () Grommet - One () Threaded Barrel - One () 7 Swedged Suspension Cable - One () Y-Cable Assembly with Cable
More informationInstruction page index: Installation Instructions for Kilo S Models KILOS-CF & KILOS-SF. Page 1 of 5. Center Feed installation Side Feed installation
Installation Instructions for Kilo S Models KILOS-CF & KILOS-SF Page 1 of 5 Instruction page index: Center Feed installation Side Feed installation 2-3 4-5 Kilo S - Instruction for center feed installation
More informationSetup. The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on series tables.
Faraday CageSetup, 2017 Setup The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on 63-500 series tables. Cage with a base plate for use on a
More information!When using electrical equipment, basic safety precautions should always be followed, including the following: AIR FOIL CLUSTER CP5371
AIR FOIL CLUSTER CP5371 Drawing: 762252XX Rev: B Sheet: 1 of 5 Eng: CLD Date Drawn: 01/30/17 TYPICAL FIXTURE 2-3/4" MOUNTING HOLE CENTERS ARM 700 ARM COVER CENTER PLATE STRUCTURAL MOUNTING 50-1/4" CP5371
More informationInstallation Instructions for Cirrus Suspension Downlight with Power - End Feed. Section One: 4" Flush Canopy Version
Doc # 0-CSP-E_0 W. Fullerton Chicago, IL 606 Ph:.0. Fax:..6 www.pureedgelighting.com info@pureedgelighting.com 06 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Suspension
More informationC 0.05" ALLEN WRENCH. Installation Instructions for Cirrus Channel Suspension T1 with 4" Square or Round Canopy. Section One: Adjusting Cable Position
Doc # 90-CST-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension
More informationConnect each sections electricity cables with a connections block or splices and heatshrink. Proceed to Myla installation manual.
MYLA L & XL ASSEMBLY 1. 2. PARTS 3-5 SECTIONS Prepare a soft clean workspace to assemble the light fixture. Carefully unpack the light fixture and other contents. Myla L consists of 3 separate sections
More information+ - 1a. 1b. c. 1d. 1e. Runway Suspended / Surface Cont. Run Installation. 2.0mm DIL DIL Revision - M 23/11/2018 Page 1
230-240V / 50-60Hz IP20 IK00 + - 2.0mm WARNING - THIS LUMINAIRE MUST BE EARTHED This luminaire has been tested and is manufactured to comply with BS EN 60598 : specification for general requirements and
More informationJ-BOX. 3-O or 4-0 MUD RING J-BOX BRACKET BAR CABLE GRIPPER/ CANOPY MOUNTING STUD 8-32 BRACKET BAR SCREWS CANOPY STRAIN RELIEF POWER CORD CANOPY
KELSEY - CSS Cable Suspended Rotational and Static CSS - Cable Suspended 3-O or 4-0 MUD RING BRACKET BAR 1/4-20 STUD 8-32 BRACKET BAR SCREWS STRAIN RELIEF POWER CORD MOUNTING GRIPPER AIRCRAFT CABLE CABLE
More informationInstallation Instructions for Zip Suspension Downlight with Remote Power and 4" Square or Round Canopy
Doc # 90-ZS-SQ_0 W. Fullerton Chicago, IL 0 Ph:.0.9 Fax:.9. www.pureedgelighting.com info@pureedgelighting.com 0 PureEdge Lighting. All Rights Reserved. Installation Instructions for Zip Suspension Downlight
More informationInde-Pendants Family. 32L Surface Mount Cylinder with Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder with Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-CRxx-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants:
More informationA524 ASSEMBLY & INSTALLATION INSTRUCTIONS BELLADONNA PENDANT CASTLETON, VERMONT USA SYNCHRONICITYLIGHTING.COM Rev A 1 OF 7
1 OF 7 COMPONENT PARTS A B Canopy Mounting Bracket C Anchor (4) D #10 Wood Screw (4) E F G H Safety Cable Ground Screw Cupped Washer Safety Cable screw I Gripper (2) J Barrel Knob (4) K L Lightbar Fixture
More informationConnecting the Channel A
20 Edge Lighting. All Rights Reserved. Installation Instructions for Cirrus Channel Suspension T, Tubular Lens w/2sq or 2RD Canopy IMPORTANT INFORMATION - This product is suitable for indoor locations.
More informationInstallation Instructions for DIY or Completed Light Channel.6 Millwork
2017 Edge Lighting. All Rights Reserved. 1718 W. Fullerton Ave Chicago, IL 60614 Tel: 77-770-1195 Fax: 77-95-561 www.edgelighting.com info@edgelighting.com LCMW.6- - - 904-LCMW.6_02 Installation Instructions
More informationFIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V)
FIXTURE INSTALLATION GUIDE Model T21T (Low Voltage Pendant Set 120V) 21T, Rev.4 6-13 IMPORTANT: Before proceeding, retrieve the GLASS SHADE INSTALLATION GUIDE, which is included with the pendant cord set
More informationINSTALLATION INSTRUCTIONS
SHD TO REMOVE HOOD (SHD) ) LOOSEN (4) SOCKET HEAD SCREWS AND RETAINING RINGS FROM HOOD (SHD). ) REMOVE HOOD AND. 3) DISCONNECT WIRES. 3 4) REMOVE REFLECTOR BY LOOSENING (4) PHILIPS HEAD SCREWS. 5) PLEASE
More informationGeneral Installation Instructions
General Installation Instructions WARNING To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions, falling parts and other hazards: Service of the equipment must
More informationThe Mind Project s Iris 1 Robotic Arm. Packing List Assembly instructions
The Mind Project s Iris 1 Robotic Arm Packing List Assembly instructions Packing list Below you will find pictures and descriptions of each part. It may be helpful to take each piece out of the bag and
More informationThe Mind Project s Iris 1 Robotic Arm. Assembly instructions Step 1
The Mind Project s Iris 1 Robotic Arm Assembly instructions Step 1 Packing list Below you will find pictures and descriptions of each part. It may be helpful to take each piece out of the bag and place
More informationInde-Pendants Family. 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types. Document No
Inde-Pendants Family 32L Surface Mount Cylinder Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-C-S-D Document No. Supplied by Litecontrol 32L Inde-Pendants: Cylinder (Surface
More informationInstallation Instructions for DIY or Completed 45 Degree Light Channel
201 Edge Lighting. All Rights Reserved. Installation Instructions for DIY or Completed Degree Light Channel IMPORTANT INFORMATION - This instruction shows a typical installation. 11 W. Fullerton Ave Chicago,
More information- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS. Factory pre-installed mud flange TOOLS REQUIRED: Phillips screwdriver, 5/16 nut driver.
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install drywall trim versions of TruGroove recessed
More informationZIP CLOUD SUSPENDED INSTALLATION MANUAL
ZIP CLOUD SUSPENDED INSTALLATION MANUAL www.delviro.com info@delviro.com 1.877.502.3434 SAFETY NOTE: Follow the Electrical Codes of the Country where this fixture will be installed. For Canada follow the
More informationA500 ASSEMBLY & INSTALLATION INSTRUCTIONS
ASSEMBLY & INSTALLATION INSTRUCTIONS 1 CONTENTS 2 Component Parts A B Canopy Mounting Plate C Cap (3) D Threaded Nipple E Threaded Standoffs (2) F Anchors (8) G #10 Screws (8) H Safety Cable (2) I Safety
More informationCloset Carousel Installation Instructions. Models TKA 5 Through TKA 14 Equipped with Footswitch Controls
Tools Required: Phillips Screwdriver (#2) Adjustable Wrench Level Tape Measure Utility Knife Electric Drill Drill Bits for Anchors Ladder (4 foot) Models TKA 5 Through TKA 14 Equipped with Footswitch Controls
More informationMultiples EM_ 1.4. Install 1X1/1X2/1X3/1X4 Housings. Installation Instructions for. This product is suitable for indoor locations.
Installation Instructions for 90EMULTI Multiples EM_. GENERAL PRODUCT I NFORMATION: This product is suitable for indoor locations. This product can be dimmed with a standard electronic dimmer or a 0-0V
More informationCNC Router Parts PRO Machine Kit Cable Track Installation Instructions
1 1 X CABLE TRACK TRAYS & BRACKETS The cable track on the side of the system is supported by a metal tray (or multiple trays for longer systems such as a PRO4896). These trays hang from brackets on the
More information**MOUNTING YOUR MONITOR
FPP72V200 72 FREE STANDING DISPLAY CART Assembly Instructions Hardware List Ref. Qty. Part No. Description AA 4 030-1128 1/4-20 UNC, 1 3/4 Socket Hd Screws BB 1 030-1129 5/8-11 UNC 1 3/4 Socket Hd Screw
More informationInstall the Housing. Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing EN3_-LH9_ 1.
Installation Instructions for Entra Round or Square Type IC, Air-tight New Construction Adjustable LED Housing 90ENTRA EN_-LH9_. LED - ROUND/ SQUARE GENERAL PRODUCT I NFORMATION: This product is safety
More informationH2-50 Hydrogen Generator Field Update
This field update is intended to provide extra protection in the event the H2 generation cell fractures or cracks. Please add the additional parts to your H2-50 as soon as possible. Please take a digital
More informationINSIDE PANEL NOT SHOWN TO DETAIL ANCHORING SYSTEM
SIX INCH ALPHA MODULE INSTALLATION KEWAUNEE SCIENTIFIC CORPORATION SIX INCH ALPHA MODULE ANCHORING SYSTEM After Alpha module has been set in desired location. Adjust the four adjustment bolts until the
More informationElements Pole Mounting System
Elements Pole Mounting System Installation Manual www.peavey.com Elements Pole Mounting System Installation Manual The Elements Pole Mounting System is a simple and straightforward pole mounting solution
More informationINSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260
INSTALLATION INSTRUCTIONS FOR HAND OPERATED MODELS: 170, 171-R, 171-N, 172, 260 I. SUSPENDED INSTALLATIONS NOTE: MODEL 260 FENSTEEL TRACK IS ASSEMBLED IN THE SAME MANNER AS DESCRIBED BELOW WITH THE EXCEPTION
More informationInstallation Instructions Standalone or continuous run configurations - 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS
- 2 JOINER ALIGNERS - 2 JOINING BRACKETS - 4 HEX BOLTS TruGroove Drywall A3 MOUNTING Ceiling INSTALLATION System Overview These instructions review how to install trimless drywall versions of TruGroove
More informationPORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12
Page 1 of 7 PORTA-DOCK, INC. AP17 APD DS 4 X 16 T12 AW17 CPD DS 4 X 16 T12 *For Beige Decking Add the Letter B to Model* Thank you for purchasing out product! *Please read these instructions and follow
More informationThank you for purchasing out product! *Please read these instructions and follow them step by step. *
Page 1 of 7 AD17 AA DS 4 X 16 T12 Thank you for purchasing out product! *Please read these instructions and follow them step by step. * STEP 1. Slide two support posts (REF. # 24) into the two outside
More informationUR20/UR28 Ouro Site/Area Luminaire Installation Instructions
17760 Rowland Street City of Industry, CA 91748 626/968-5666 FAX 626/369-2695 UR20/UR28 Ouro Site/Area Luminaire Installation Instructions! WARNING: Fixtures must be grounded in accordance with local codes
More informationUser Instructions Multiline Otter Scoreboard Caddy Assembly
List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)
More informationSAE of 7 "R" (REGRESSED) POSITION "S" (SHIELDING AT TOP) POSITION. Tools Required
SAE 0 5/6'' Exposed TBar Ceiling FINISHED EDGE WITH JANGLE 90 IC CORNER KIT 5 7/6" 38mm 9/6'' Screw Slot TBar Ceiling "R" (REGRESSED) POSITION 6" CEILING OPENING "S" (SHIELDING AT TOP) POSITION SUPPORT
More informationInde-Pendants Family. 32L Ring Plaster Trim, Grid and Drywall Ceiling Types. Document No Installation instructions for 32L-Rxx-P
Inde-Pendants Family 32L Ring Plaster Trim, Grid and Drywall Ceiling Types Installation instructions for 32L-Rxx-P Document No. Supplied by Litecontrol 32L Inde-Pendants: Ring (Plaster Trim, Grid and Drywall
More informationINSTALLATION INSTRUCTIONS FOR HAND OPERATED SILENT STEEL ADC HEAVY DUTY CURTAIN TRACK MODELS: 280, 281, 282, 280-A, 283-N, 283-R
INSTALLATION INSTRUCTIONS FOR HAND OPERATED SILENT STEEL ADC HEAVY DUTY CURTAIN TRACK MODELS: 280, 281, 282, 280-A, 283-N, 283-R I. SUSPENDED INSTALLATIONS 1. Lay the two track halves on the floor with
More informationINSTALLATION INSTRUCTION Silo Multiples - New Construction Housing MT-4*15, MT-4*10
IMPORTANT SAFETY INSTRUCTIONS 1. Read all instructions before installing. 2. System is intended for installation by a qualified electrician in accordance with the National Electrical Code and local regulations.
More informationINSTALLATION INSTRUCTIONS FIXTURE SERIES: SAE 202 MOUNTING TYPE: RECESSED WALL / SLOT PAGE: 1 OF 8
INSTALLATION INSTRUCTIONS FIXTURE SERIES: SAE 202 MOUNTING TYPE: RECESSED WALL / SLOT PAGE: 1 OF 8 90v INNER CORNER KIT "R" (REGRESSED) POSITION CROSS-SECTION VIEW "S" (SHIELDING AT TOP) POSITION CROSS-SECTION
More informationTH Place, Maspeth, NY Instruction Manual for UNO Exit Signs
57-10 49 TH Place, Maspeth, NY 11378 Instruction Manual for UNO Exit Signs 1. What is included in this box? Back box with electronics, battery (where applicable), & mounting hardware. Inner trim, LED illuminator
More informationIMPORTANT SAFETY INSTRUCTIONS:
Online: www.ballarddesigns.com PRODUCT NAME: MR Geometric Chandelier ITEM NUMBER: LC971 DIMENSIONS OF ITEM ASSEMBLED: FLUSH- 36 H x 42 W x 30 1/2 D HANGING- 96 H x 42 W x 30 1/2 D HANGING FIXTURE: FLUSH
More informationMaxLite Linear Strip ECO Series
General Safety Information To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions
More informationLine volt rail & fixtures. Low volt quick connect fixtures with transformers
INSTRUCTIONS: Line Volt Flexrail2 Safety Instructions: A qualified electrician must install system only. System is intended for installation in accordance with National Electric Code, local and Federal
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationDETAILED ILLUSTRATION
FCF1100 Series (Mounting Knuckle to J-Box JB) - INSTALLATION INSTRUCTIONS electricity has been turned off and electrical 4) Reattach j-box cover, gasket and fixture to the j-box. to read these instructions
More informationBL-ER-P Ethernet Radio Unit for Pedestal Installation Guide
Assemble the Antenna Riser 1. Remove the antenna riser assembly and the antenna from its packaging. 2. Remove the plastic cap, the nut, and the lock washer from the stem of the antenna. 3. Put the stem
More informationWOLF LOOM DOUBLE BACK BEAM
WOLF LOOM DOUBLE BACK BEAM Assembly Instructions Find out more at schachtspindle.com Schacht Spindle Company 6101 Ben Place Boulder, CO 80301 p. 303.442.3212 f. 303.447.9273 2017 Schacht Spindle Company,
More informationCustom Pendant- Hardwire Assembly and Installation Instructions
Custom Pendant- Hardwire Assembly and Installation Instructions CAUTION: BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX.
More informationFan, Eden/Northfield, GS Installation Instructions (SKU ) Packing List
Packing List Blower Assembly Wiring Harness Rheostat with Nut and Knob Snap Disc Mounting Hardware (4) rubber grommets with brass inserts, (4) nuts, (4) washers. Cover Assembly Installation Warning: Make
More informationINSTALLATION INSTRUCTION Solorail - Low Voltage Starter Kit
IMPORTANT SAFETY INSTRUCTIONS: Read all instructions. Turn off power at main switch before installing or modifying the system. Do not install the system: - Within six inches of any curtain or combustible
More informationWhat you should have. 1. Telescopic Pole (1) 2. Arc tubing (4) for Lower Ring. 3. Numbered bars or spokes(8) 4. Center plate (1)
20 ft RGB Pole Tree What you should have 1. Telescopic Pole (1) 2. Arc tubing (4) for Lower Ring 3. Numbered bars or spokes(8) 4. Center plate (1) 5. Top Ring (1) 6. Hardware and wrenchs a. Hardware i.
More informationINSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger
INSTALLATION INSTRUCTIONS FOR FRONT CASTING DECK RAIL Ranger TOOLS REQUIRED FOR INSTALLATION: Drill motor, (1) 5/16 inch drill bit, (1) 13/64 drill bit, (1) 3/16 inch hex wrench (1) 3/32 inch hex wrench.
More informationEchoPanel EchoScreen Installation Guide
Please read this application guide before beginning installation. This installation guide is presented to help in the installation of Kirei EchoScreens. Kirei accepts no responsibility for installation
More informationFixed Wall Arm. Installation Guide. Part number Rev E 2012 PolyVision Corporation All rights reserved
Fixed Wall Arm Installation Guide Part number 2002003-001 Rev E 2012 PolyVision Corporation All rights reserved Table of contents Important Safety Instructions... 3 Overview... 4 Important considerations...
More informationSURFACE CLIP MOUNT. 1 Insert lens into channel, measure, and cut to length. Remove lens cover from channel. surface. Attach lens cover and end caps
SURFACE CLIP MOUNT 1 Insert lens into channel, measure, and cut to length Remove lens cover from channel Screw mounting clips into mounting Snap channel into mounting clips Attach lens cover and end caps
More informationTHIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
LumeLEX 2026 SERIES INSTALLATION INSTRUCTIONS Important THIS SHEET CONTAINS IMPORTANT SAFETY INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Warning This product must be installed in accordance with National Electrical
More informationCook's Corner Kitchen Assembly Instructions
Assembly Instructions 00 Melissa & Doug, LLC All rights reserved 0 We care about your comments Please call us! -800-84-948 www.melissaanddoug.com PARTS D A E I ( pieces) Q N B F J R ( pieces) S ( pieces)
More informationPRS X-Axis Energy Chain (E-chain) Installation
Page 1 PRS X-Axis Energy Chain (E-chain) Installation ShopBot Tools, Inc. 3333-B Industrial Drive, Durham NC 27704 ShopBotTools.com Technical Support support@shopbottools.com 1-888-680-4466 Page 2 Table
More informationSeriesTWO RGB Fluorescent Fixtures. Installation and Instruction Manual
SeriesTWO RGB Fluorescent Fixtures Installation and Instruction Manual Brightline LP 580 Mayer Street #7, Bridgeville PA 15017 Phone 1-412-206-0106 Fax 1-412-206-0146 www.brightlines.com The Brightline
More informationAssembly & Installation Instructions
1 OF 6 Component Parts A Fixture Pipe (3) B Coupling (3) C Canopy Pipe (3) D Middle Canopy Can E Clutch (3) F Plastic Sleeve (3) G Side Canopy Can (2) H Set Screw (3) I Middle Crossbar J #10 Screws (4)
More informationQuantum 2 SQUARE 0808K
Installation Instructions #CH-S-0808K-KIT #CH-S-0808K-2FT #CH-S-0808K-4FT #CH-S-0808K-6FT #CH-S-0808K-8FT Custom #CH-S-0808K Sections: Pg. 2 Fixture Kit Channel Preparation Pg. 7 Pg. 9 Surface Mount Installation
More informationMounting a BalanceBox 400 to a brick wall
Unpack the BalanceBox 400 and remove the Wall frame cover and its bag of screws. Slide the cover out at the top. NOTE: the cover is NOT included with the BalanceBox 400H LOCK SCREW HOLE MOBILE STAND MOUNTING
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationAssembly & Installation Instructions
1 OF 6 Component Parts A B C Fixture Mounting Bracket Canopy D Threaded Standoffs (2) E Cap (2) F Anchors (4) G #10 Screws (4) H I J K Safety Cable #8 Screw Ground Screw Cupped Washer Socket Assembly (6)
More informationBluetooth DRO Installation for Bench Mills
The premier source of tooling, parts, and accessories for bench top machinists. Bluetooth DRO Installation for Bench Mills These instructions describe how to install the following products: 5494: Digital
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review
More informationInstallation Instructions
Installation Instructions Optima LED 8 Double-Sided StretchLite Perimeter Lit Graphic Display Line Voltage Connector Optima LED DS5 (Double-sided StretchLite Graphic Display) with Graphics Corner Bracket
More informationShowpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV
Showpiece Cabinet Integrated Stand For 32" - 52" LCD HDTV Installation and Assembly Instructions 2009 Incredible Technologies Inc. Version 0109 Showpiece Cabinet Integrated Stand for 32" - 52" LCD HDTV
More informationJoiner Kit Joiner bracket (x1) Biscuit aligners (x2) Trim Flange
- Trim System Overview These instructions review how to install TruGroove Perimeter fixtures. Modules can be installed as individual standalone units, or they can be joined together to create continuous
More informationArched Top Lantern Pendant Assembly and Installation Instructions. Country of Destination: US/CN UK/EU/AUS Middle East
CAUTION: Arched Top Lantern Pendant Assembly and Installation Instructions Country of Destination: US/CN UK/EU/AUS Middle East BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF
More informationGLASS GLOBE MOBILE LINEAR CHANDELIER
PARTS ENCLOSED: (B) Top ceiling plate [1] (C) Bottom ceiling plate [1] (D) Glass globes [7] (E) Screws [6] (F) Nuts [5] (G) Extension rods [15] (H) Transformer [1] (I) Threaded inserts [5] (J) 1.6W LED
More informationA59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK
Page 1 of 5 PORTA-DOCK, INC. A59 APD & A86 CPD 5'X 16' SW ALUMINUM PORTA-DOCK *For Beige Decking Add the Letter B to model* Thank you for purchasing our product! *Please read these instructions and follow
More informationS A F T E Y W A R N I N G
BINDING CUTTING BASE This tool is designed to fit on a Porter Cable Model 310 and 3701 trim router, this combination will provide you with an easy way to accurately cut a binding rabbet on you instrument.
More informationBY ALIEN TECHNOLOGIES CORP
BY ALIEN TECHNOLOGIES CORP Assembly Instructions TopLift Pros YOU MAY ALSO REVIEW OUR ASSEMBLY VIDEO, PLAY AND PAUSE AT YOUR CONVENIENCE. JUST VISIT US AT WWW.TOPLIFTPROS.COM AND GO TO Customer Support
More informationINSTALLATION GUIDE Ceiling TV Mount MHP-52
ISTLLTIO GUIDE Ceiling TV Mount MHP-52 Max Load Capacity: 125 lbs (57kg) ote: Read entire instruction sheet before you start installation and assembly. Be sure to read this entire manual thoroughly and
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationInstalling the 3 Indexer: PRS Standard Tools
888-680-4466 ShopBotTools.com Installing the 3 Indexer: PRS Standard Tools Copyright 2016 ShopBot Tools, Inc. page 1 Copyright 2016 ShopBot Tools, Inc. page 2 Table of Contents Route Cable into Box...5
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
More informationPRE-ENGINEERED HORSE STALL SYSTEMS SDFD SLIDING DOOR c/w FOLD-DOWN GRILL. & Assembly. Installation Instructions
PRE-ENGINEERED HORSE STALL SYSTEMS 4800 SDFD SLIDING DOOR c/w FOLD-DOWN GRILL & Assembly Installation Instructions 4800 SDFD Sliding Door c/w Fold-Down Grill Components - 1 3 /4" x 2" x 88" channels (2)
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Flat Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationImportant Safety Instructions
Basis Track Installation Guide Important Safety Instructions Lighting systems from Translite Sonoma are supplied as complete systems. Use only factory-supplied parts to preserve the validity of the UL
More informationTilting Flat Panel Wall Mount Installation Guide
Tilting Flat Panel Wall Mount Installation Guide Model: A580TM Easy installation Built-in level for easy positioning Safety bolts lock the TV on the mount Easy to adjust tilt angles: +5 to -15 degrees
More informationmila-wall (Series100) General Operating Instructions page 1 of 15
mila-wall (Series100) General Operating Instructions page 1 of 15 Step #1: Before setting up walls, lower adjustable leveling feet on each panel approximately 1". This will allow access to the threaded
More informationFAIRFAX ROUGHING-IN K-12151T=673. UNIT: mm K-12153T K-12156T K-12151T=610 K-12157T K-12161T T01-A -1- INSTALLATION INSTRUCTIONS
FAIRFAX INSTALLATION INSTRUCTIONS BATHROOM ACCESSORIES K-12151T/K-12153T/K-12156T/ K-12157T/K-12158T/K-12161T/K-12162T BEFORE YOU BEGIN Congratulation on your purchase of this high quality Bathroom Accessory.
More informationNemalux INSTALLATION INSTRUCTIONS APPLICATION 1-4
I N D U S T R I A L rev. A- INSTALLATION INSTRUCTIONS *PENDING* E77827 E77827 APPLICATION MR3 & MR6 Luminaires are suitable for use in the following areas as defined by the National Electrical Code (NEC)
More informationQUANTUM 2 CIRCLE 24 Installation Instructions
Installation Instructions #CH-C-24-KIT #CH-C-24-2FT #CH-C-24-4FT #CH-C-24-6FT #CH-C-24-8FT Custom #CH-C-24 Sections: Pg. 2 Fixture Kit Channel Preparation Pg. 6 Suspension Installation Version 3 Page 1
More informationNash Chandelier Assembly and Installation Instructions
CAUTION: Nash Chandelier Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY BOX. Important
More informationMonitor mount for 2016 E-series and E2417H Dell monitors. Installation guide
Monitor mount for 2016 E-series and E2417H Dell monitors Installation guide Notes, cautions, and warnings NOTE: A NOTE indicates important information that helps you make better use of your product. CAUTION:
More informationAssembly Instructions
Moss provides: - Wrench - Gloves - Wash Cloth - 33 Cleaner - Plastic Drop Cloth 2 GENERAL INSTRUCTIONS: - Wipe down all tubing, clean work area and lay out plastic sheeting. - Repack fabric neatly in the
More informationWoven Leather Chandelier Large Assembly and Installation Instructions
CAUTION: Woven Leather Chandelier Large Assembly and Installation Instructions BEFORE INSTALLING FIXTURE, MAKE SURE THE POWER TO THE CIRCUIT IS TURNED OFF AT THE MAIN FUSE BOX / CIRCUIT BREAKER UTILITY
More informationQUANTUM 2 TRAPEZOID 2509 Installation Instructions
Installation Instructions #CH-T-2509-KIT #CH-T-2509-2FT #CH-T-2509-4FT #CH-T-2509-6FT #CH-T-2509-8FT Custom #CH-T-2509 Sections: Pg. 2 Fixture Kit Channel Preparation Pg. 6 Suspension Installation Version
More informationPRS X-Axis E-Chain Installation For Tools with a 12 Z-Axis
888-680-4466 ShopBotTools.com PRS X-Axis E-Chain Installation For Tools with a 12 Z-Axis This kit is compatible with PRS Shopbots that have an X-axis cutting area of 96 to 144. It is not immediately compatible
More informationMyStudio VS53 Versa Sweep Setup Instructions
MyStudio VS53 Versa Sweep Setup Instructions MISSION STATEMENT Pro Cyc, Inc. is the world leader in design and sales of modular infinity backgrounds. Our studio systems are recommended by every major company
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS MAXIMUM PRIVACY HIGH PRESSURE LAMINATE (HPL) TOILET PARTITIONS 2030 TrimLineSeries 2040 DesignerSeries IMPORTANT: Storage and Handling Information on last page. Review these instructions
More informationINSTALLATION RECOMMENDATIONS For The Con-Tech ODYSSEY Line Voltage Flexible Track System
INSTALLATION RECOMMENDATIONS For The Con-Tech ODYSSEY Line Voltage Flexible Track System IMPORTANT SAFETY INSTRUCTIONS: Read all instructions before installation. Save these instructions for later use.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
More information