FSH. ility VE1260 V

Transcription

1 FSH High Security Motorised Drop Bolt With Pre-Load Capab ility VE1260 INSTALLATION MANU AL 1

2 A. Introduction The VE1260 is a motor driven Dropp Bolt with pre-load capability. The VE1260 may be commonly installed vertically in the lock style of the door frame orr horizontally in the door frame header, it has a symmetric dead-bolt mechanism to t allow the device to be used on 180 degree swing through doors. B. Features Provides for door misalignment+/- 4.0mm from the door centre, 8.0mm in total with standard 27mm wide Strike Plate. Capable of +/ /-12.0mm (24mm total) with wider Strike Plate (see accessoriess section for ordering information). Pre-Load /Side load capability: o 3 wire (motorised) unlocking mode o 2 wire unlocking mode o Locking up to 35kgg up to 6kg up to 7kg Simple PTO/PTL Locking Mode changeover Small size (fits into most existing standard drop bolt cutouts) C. Applications The VE1260 Motorized Drop Bolt can operate with any type of access control or intercom system as the sole means of locking, either hinged or pivot hung doors including 180degree swing through doors. It can also be applied to hinged doors as an additional locking l device to add extra security and strength too a door set. Because of its size it can be used as a replacement for existing standard drop bolts with little or, in some cases, no modification ns to the door or door frame. In combinatio on with a stainless steel surfacee mount box, the VE1260 is suitable for frameless glass doors and glasss frames. The T lock can be either mounted horizontally in the door header or vertically in the door frame lock style. 2

3 D. Technical Specification Power Input Power Consumption Monitoring switch specification Wiring Requirements PTL (Fail Safe) Wiring Requirements PTO (Fail Secure) Wiring Bolt Position Monitoring (unlocked position) Wiring Door Position Monitoring Durability Strength Operating Temperature Maximum Door Gap Certifications 11-30VDCC Minimum 1A Regulated Power Supply S recommended Locking/unlocking cycle currentt is 0.25 to 1A depending on the side load. More side load = more current. After locking/unlocking the current drops down to ~0.015A(15mA) Bolt changeover switch 30VDCC 0.1A Max Door position reed switch 30VDCC 0.35A Max 3 Wire Configuration (Recommended) Black 0v Red Continuous Positive 11-30VDC Blue Access control. Connect to positive to activate the bolt. (Strike plate magnet must be present) 2 Wire Configuration Black 0v Red and blue are connectedd together. When power is applied to thee Red/Blue wires and the strike plate magnet is present the VE12600 will lock 3 Wire Configuration Black 0v Red Continuous Positive 11-30VDC Blue Access control. Disconnect D from positive to activate the bolt. (Strike plate magnet must be present) Connect to Positive to unlock. 2 Wire Configuration There iss no 2 wire configuratio on for PTO ( Fail Secure) ) White Purple Orange Green -Reed switch Green -Reed switch Normally Open, with door open The door has to be closed to activate the Door Position Monitoring. The lock has to be lined up with the strike plate within the t tolerances of +/- 4mmm to activate the lock. Meeting Australian Standard AS operating cycless Durability D7 Meeting Australian Standard AS Static Strength S8 (611kg for 1 minute) Impact Strength S8-20 to +60 degree Celsius. 8mm -(NO) -(COM) -(NC) CE C-Tick Fire ratedd in accordance withh AS Part 1 & BS476 to up to 4 hours on fire door assemblies a 3

4 E. Locking Mode setting PTL(Fail Safe) )/PTO(Fail Secure). The operation mode is set by a small changeover switch on o the sidee of the lock. The default setting from the factory is Power to Lock (Fail Safe). S If Power to Open (Fail Secure) is required, use the changeover switchh to reset the Lockingg Mode. If the lock has been powered up, it may be necessary to either e remove powerr to the lock for 5 minutes or cycle the lock once too ensure that the changeover has come into effect. PTO PTL PTL(Fail Safe)/PTO(Fail Secure) Changeover switchh F. Wiring Diagram 4

5 G. Product & Cut-Out Dimensions Locking Device VE1260R Round Edge: Locking Device VE1260S Square Edge: 5

6 Strike Plate VE1260R Round Edge: Strike Plate VE1260S Square Edge: 6

7 H. Installation a. Door Frame and Door preparation detail for Lockingg Device and Strike Plate Before commencing with the installation ensure the gap between b door and frame is lesss than 8mm Mark Line 1 (Strike Plate) corresponding to center line of o Door Mark Line 2 (Lock) corresponding with Line 1 on the Door Frame Note: Ensure Line 1 and Line 2 align when the door is in thee closed position. Mark Line 4 on the Door Frame, corresponding to the topp edge of the lock faceplate (square edge) or centree of top mounting hole (round edge). Mark Line 3 on the Door, ensuring it is aligned with corresponding line 4 on the Door Frame. Mark and recess cut-out of strike plate and lock faceplate using Line 1 as the centre guide and Line 3 as the height guide Cut out a 22mmm wide and 20mm deep cavity in the door underneath the strike plate for the bolt to be able to fully engage.. Installl the strike plate on the door, and lock in door frame. Ensure the door gap between the strike plate and the faceplate onn the locking device is not more than 8mm Note: Thickness of strike plate & faceplate = 3mmm 7

8 b. Installationn of Locking Device and Strike Plate VE1260R Round Edge 8

9 VE1260S Square Edge Ensure all wiring connections are correct and insulated, with w no wires contacting any sharp edges. Install the locking device into the door frame and strike plate p on door as shown above. Connect the device and apply power, allow the door too open and close normally. When the door closes and the magnet of the strike plate is line up within the locking range, the bolt of the locking device will engage within the strike plate and lock the door. Ensure Volts is measured at thee lock during locking.. 9

10 I. Notes Locking device must only be used inn weather protected areas. Locking device must only be installedd vertically or horizontally withinn or on the door frame. Floor mounting is not recommendedd and will void the warranty. Locking device requires a strike platee to operate. It also requires r thee strike plate to correctly align with the lock faceplate. J. Accessories and Ordering Information Electromechanical Drop Bolts VE1260R VE1260S VE-Lock Pre-Load Drop Bolt 25mmm Face Plate including 27mm Strike Plate ROUND EDGE VE-Lock Pre-Load Drop Bolt 30mm Face Plate including 27mm Strike Plate SQUARE EDGE (PADDE ES8000 Replacement) Accessories VE1260R-GL VE1260LED-BOX VE1260R-SCEC VE1260S-ST6 VE1260S-ST9 VE1260S-ST12 Single Glass Door Box for VE1260R Lock or VE1260R-ST4 Strike S Plate ROUND EDGEE LED Monitor Box for Lock-Status Monitoring Indication (Red/Green) Security Bracket for VE1260R Strike Plate 31mm forr VE1260 Series to cater for -/+6mm door misalignment minimumm Door Thickness 35mm SQUARE EDGEE Strike Plate 35mm forr VE1260 Series to cater for -/+9mm door misalignment minimumm Door Thickness 40mm SQUARE EDGEE Strike Plate 40mm forr VE1260 Series to cater for -/+12mm door d misalignment minimum Door Thickness 50mm SQUARE EDGE Spare Parts VE1260R-ST4 VE1260S-ST4 Standardd Strike Plate 27mm Sparee Part for VE1260R to cater for -/+4mmm door misalignment ROUND EDGE Standardd Strike Plate 27mm Sparee Part for VE1260S to cater for -/+4mmm door misalignment SQUARE EDGE 10