Product Detail Manual Purpose and Content

Transcription

1 Product Detail Manual Purpose and Content It is not the intent of this catalog to show the limitations of the Dri- Design product line, but rather to show the concept of Dri-Designs products that may be custom modified for application of specific products. Dri-Design welcomes the opportunity to assist in the design and application of its products. Details shown in this manual are for the purpose of best illustrating the product. In many cases specific construction and sealant details have been omitted from the illustrations. Assembly and installation instructions should be obtained from Dri-Design prior to installation. The weather barrier must be installed per the manufacturers published instructions. In order to provide the best possible products, Dri-Design reserves the right to modify components without prior notice. Laws, building codes and safety codes vary widely concerning the design and use of metal wall panels. Dri-Design does not control the selection and use of its standard products and therefore assumes no responsibility for misapplication.

2 Dri-Design System Details EXTRUSION & LASHING DETAIL INDEX Detail Index: Detail 1: Parapet Detail 2: Horizontal Joint Detail 3: Sill Detail 4: Window Head Detail 5: Window Sill Detail 6: ascia to Soffit Detail 7: Soffit to Vertical Wall Detail 8: Jamb Detail 9: Vertical Joint Detail 10: Window Jamb Detail 11: 90 Outside Corner Detail 12: 90 Inside Corner Detail 13: 135 Outside Corner Detail 14: 135 Inside Corner There are several ways to detail Dri-Design. Under each detail number above, there are multiple installation options to chose from. All details are shown with a 5/8" plywood substrate. or alternate substrate installation examples, see details 2 & 9. The details in this binder are only a sample of our standard details. Please contact Dri-Design directly with any questions regarding your specific project as well as pricing.

3 PARAPET COPING DETAIL 1

4 INTEGRATED COPING DETAIL 1A

5 GENERIC HEAD EXTRUSION DETAIL 1B

6 GENERIC HEAD LASHING DETAIL 1C

7 TYPICAL HORIZONTAL JOINT NOTE: CONTACT DRI-DESIGN OR CUSTOM HORIZONTAL REVEAL OPTIONS. 2

8 TYPICAL HORIZONTAL JOINT OVER OSB OR GYP. SHEATHING NOTE: CONTACT DRI-DESIGN OR CUSTOM HORIZONTAL REVEAL OPTIONS. 2A

9 TYPICAL HORIZONTAL JOINT OVER PRE- ENGINEERED BUILDING NOTE: CONTACT DRI-DESIGN OR CUSTOM HORIZONTAL REVEAL OPTIONS. 2B

10 TYPICAL HORIZONTAL JOINT OVER PRE-CAST CONCRETE OR C.M.U. NOTE: - CONTACT DRI-DESIGN OR CUSTOM HORIZONTAL REVEAL OPTIONS. - DRI-DESIGN CAN BE INSTALLED DIRECTLY TO MASONRY OR PRECAST CONCRETE WITHOUT THE USE O SUB-GIRTS BUT THIS CAN COMPLICATE INSTALLATION. 2C

11 TYPICAL HORIZONTAL JOINT OVER Z-GIRT AND INSULATION NOTE: CONTACT DRI-DESIGN OR CUSTOM HORIZONTAL REVEAL OPTIONS. 2D

12 GENERIC SILL DETAIL WITH "J" EXTRUSION 3

13 SILL DETAIL AT STONE (EXTRUSION) 3A

14 GENERIC SILL DETAIL WITH "J" LASHING 3B

15 PANEL SILL AT STORERONT HEAD 4

16 PANEL SILL WITH 4" RETURN LEG EXTRUSION AT STORERONT HEAD 4A

17 PANEL SILL AT STORERONT HEAD (LASHING) 4B

18 PANEL SILL WITH "J" LASHING & RETURN AT STORERONT HEAD 4C

19 PANEL HEAD AT STORERONT SILL (EXTRUSION) 5

20 PANEL HEAD AT STORERONT SILL (LASHING) 5A

21 ASCIA SOIT DETAIL OPTION #1 (EXTRUSION) 6

22 ASCIA SOIT DETAIL OPTION #2 (EXTRUSION) 6A

23 PANEL SILL AT SOIT (EXTRUSION) 6B

24 ASCIA SOIT DETAIL OPTION #1 (LASHING) 6C

25 ASCIA SOIT DETAIL OPTION #2 (LASHING) 6D

26 PANEL SILL AT SOIT (LASHING) 6E

27 SOIT TO VERTICAL WALL DETAIL (EXTRUSION) 7

28 PANEL HEAD AT SOIT (EXTRUSION) 7A

29 PANEL HEAD AT SOIT (LASHING) 7B

30 TYPICAL JAMB DETAIL (EXTRUSION) 8

31 TYPICAL JAMB DETAIL (LASHING) 8A

32 TYPICAL VERTICAL JOINT NOTE: CONTACT DRI-DESIGN OR CUSTOM VERTICAL REVEAL OPTIONS. 9

33 CUSTOM 1/8" VERTICAL JOINT 9A

34 TYPICAL VERTICAL JOINT OVER OSB OR GYP. SHEATHING NOTE: CONTACT DRI-DESIGN OR CUSTOM VERTICAL REVEAL OPTIONS. 9B

35 TYPICAL VERTICAL JOINT OVER PRE- ENGINEERED BUILDING NOTE: CONTACT DRI-DESIGN OR CUSTOM VERTICAL REVEAL OPTIONS. 9C

36 JAMB DETAIL AT STORERONT (EXTRUSION) 10

37 JAMB DETAIL AT STORERONT (LASHING) 10A

38 90 OUTSIDE CORNER (EXTRUSION) 11

39 90 OUTSIDE CORNER (LASHING #1) 11A

40 90 INSIDE CORNER (EXTRUSION) 12

41 90 INSIDE CORNER (LASHING) 12A

42 135 OUTSIDE CORNER (LASHING) NOTE: OTHER ANGLES CAN BE ACCOMPLISHED USING THIS SAME DETAIL. 13

43 135 INSIDE CORNER (LASHING) NOTE: OTHER ANGLES CAN BE ACCOMPLISHED USING THIS SAME DETAIL. 14