SEAL PLATE SP4413 VERTICAL SP4414 1"[25] VERT. PANEL JTS. 1/2"[13] INTERM. SPLICES DESIGN LOADS AND SLAB EDGE DISTANCES. 1 2 NOM.

Transcription

1 3 COL 5 16GA. ANGLE SP4413 VERTICAL SEE SUPPORT DRAINGS 1 7/16 SEAL VERT. JNT 1/2 [13] Ă DETAILER NOTE OPTIONAL INSULATION HEN REQUIRED. OF SEAL PLATE PANEL MODULE FROM SHELF OF TR. TO TOP OF FLASH 3/8 [10] Ă 1 BP SUPPS 1 1/4 MASONRY 18 F PAINTED 12 O.C. NOTE: THE FASTENER HEAD IS NOT TO TEND PAST THE FACE OF THE SEAL PLATE. THE LOCATION OF THE FASTENER SHOULD BE BETEEN SEALANT TRACK & GASKET SP4414 1[25] VERT. PANEL JTS. 1/2[13] INTERM. SPLICES BOTTOM EEPS PROVIDE CLEARANCE FOR FLASHING ANCHOR BOLT SEE NOTE ā CURING BUTYL 3/8 [10] Ă NOM. NOTE: LOCATION AND SIZE OF ANCHOR BOLT IS TO BE DETERMINED BY SPECIFIC PROJECT DESIGN LOADS AND SLAB EDGE DISTANCES. FDS 3TH SEAL PLATE BASE AT SLAB (extruded) 3TH SP-0001

2 COL SP4413 VERTICAL SEAL PANEL VERT. JNT. 3 1/4 16GA. ANGLE 1/2 [13] VERT. JNT. OF SEAL PLATE CONT. SEE SUPPORT DRAINGS 3/8 [10] Ă 3/8 [10] Ă BOTTOM SP4414 EEPS SP4414-LS FROM SHELF OF TR. TO TOP OF FLASH 26 1 BP 24 O.C. ANCHOR BOLT T/CURB 3 16 SILICONE SEALANT 1/2 [13] x 3/8 [10] 7/8[22]Ă BACKER ROD CURING BUTYL 3/8 [10] Ă FDS 3TH SEAL PLATE SLAB - ON MODULE NOTE: NBC LOCATION AND SIZE OF ANCHOR BOLT IS TO BE DETERMINED BY SPECIFIC PROJECT DESIGN LOADS AND SLAB EDGE DISTANCES. 3TH SP-0002

3 COL SP4413 VERTICAL SEAL PLATE 1/2 [13] VERT. JNT OF SEAL PLATE 3 1/4 16GA. ANGLE CONT. 1/2 [13] Ă 14-14x 1 18 OC BOTTOM SP4415 EEPS SP4415-LS FROM SHELF OF TR. TO TOP OF FLASH (2) CONTINUOUS 26 3/8 [10] Ă 3 4 SEE SUPPORT DRAINGS 1 ANCHOR BOLT SEE NOTE T/CURB SILICONE 1/2 [13] x 3/8 [10] 7/8[22]Ă BACKER ROD CURING BUTYL 3/8 [10] Ă FDS 3TH SEAL PLATE SLAB - OFF MODULE NOTE: 1 1/4 TAPCON LOCATION AND SIZE OF ANCHOR BOLT IS 18 O.C. TO BE DETERMINED BY SPECIFIC PROJECT DESIGN LOADS AND SLAB EDGE DISTANCES. 3TH SP-0003

4 1 SP4342 w/end BLOCK SP4342-LS w/1 BB TAPE 3/8 [10] Ă CONT. TOOLED BEAD CONT. TO NOTE: CONTINUOUS PANEL LINER FLASH ADHERE, SEAL OR USE A COMPATIBLE HIGH GRADE TAPE TO CONNECT ROOF MEMBRANE 3 COL 3/16 BULB-TITE 12[305] O.C. 3/8 [10] Ă ā1 1 3/8 [10] Ă 3/8 [10] SEAL PLATE 5/8[16]Ă BACKER 1/2 [13] x 3/8 ROD [10] SILICONE 1 SS 135Ā T/COPING M8 SHIMS AS REQD ALTERNATE COPING 3 TOS ā 135Ā SS PANEL MODULE PANEL CLIP AND FASTENER REVEAL 26 PARAPET BACK-UP NBC ROOFING MATERIAL NBC SEE SUPPORT DRAINGS 2 3 FDS 3TH SEAL PLATE TRUDED COPING #1 3TH SP-0004

5 2 (MIN) TO NOTE: CONTINUOUS PANEL LINER FLASH ADHERE, SEAL OR USE A COMPATIBLE HIGH GRADE TAPE TO CONNECT ROOF MEMBRANE 3/16 BULB-TITE 12[305] O.C. 3/8 [10] Ă 135Ā T/COPING 3/8 [10] Ă 3/8 [10] Ă REVEAL -1/ CONT. 3 TOOLED BEAD CONT. COL 18 AS SEAL PLATE 3/8 [10] Ă ā1 135Ā ALTERNATE COPING 1 TOS 2 PANEL MODULE 1 8 PANEL CLIP, FASTENER & P44 SPACER (SPACER) #10-16x5/8 SD 1 8 NORTON V x 3 LONG 18 O.C. C 18[457] O.C. REVEAL FDS 3TH SEAL PLATE METAL COPING SS 26 PARAPET BACK-UP NBC ROOFING MATERIAL NBC SEE SUPPORT DRAINGS 2 3 3TH SP-0005

6 3 COL SP4413 VERTICAL SEAL PLATE SEE SUPPORT DRAINGS 3/8 [10] VERT. JNT OF SEAL PLATE 16 F PANEL MODULE FROM SHELF OF TR. TO TOP OF FLASH SOFFIT NBC SUPPORT NBC SS 18[610] O.C SP4414 1[25] VERT. PANEL JTS. 1/2[13] INTERM. SPLICES SS 24[610] O.C. 3/8 [10] Ă ā SP4414-LS w/1[25] BB TAPE & DO 791 AT INTERM. SPLICES SP4414-GP SEAL NBC PTD END ALLS TRIM HEM & SEALANT FLASHING NEEDS PLUGGED /BACKER ROD 1 2ā (16GA MINIMUM) FDS 3TH SEAL PLATE SOFFIT (by others) 3TH SP-0007

7 SP /SP4413 LAP STRIP PANEL CLIP, FASTENER & P-44 SPACER (TYP) SEE SUPPORT DRAINGS 7 MINIMUM PANEL MODULE REVEAL SHOP APPLIED FLASHING, SEALANT AND FASTENERS SUPPS TERMINATION PLATE 26 F SOFFIT END JOINT BACKER FLASH 3 SHOP FORMED BENT PANEL 7 MINIMUM FDS 3TH SEAL PLATE / IMV SOFFIT (shop formed longitudinal bend panel) REVEAL INSTALL SOFFIT PANEL BEFORE BEND PANEL PANEL MODULE 3TH SP-0009

8 COL 5 SEE SUPPORT DRAINGS 3ā FA_ O.C. 3/8 [10] Ă PANEL CLIP, FASTENER & P-44 SPACER 3 MIN. 1 OVERLAP PANEL MODULE EL. REVEAL 3/8 [10] Ă 3 FDS 3TH IMV SOFFIT - REAR 3TH SP-0010

9 6 MIN. 3 SEE SUPPORT DRAINGS w/ 2-INCH STEEL TUBES PANEL CLIP AND FASTENER 6 MIN. 3 3 PANEL NOTCH METAL STUDS 1/2 [13] Ă PANEL NOTCH 5 8 NOM NOTE 'A' 6'-0 LENGTH 7'-6 LENGTH FDS 3TH SEAL PLATE VERTICAL JOINT 3TH SP-0011

10 NOTE: HERE END JOINTS OCCUR IN VERTICAL SUPPORTS, USE BRIDGE FLASHING BEDDED IN NON-CURING BUTYL OVER THE GAP IN SUPPORTS. 1/2 [13] Ă 3 PANEL CLIP AND FASTENER 6 MIN. 5 8 NOM. MIN. 6 1/2 [13] Ă SHOP APPLIED FLASHING, SEALANT AND FASTENERS SP4313 SEE SUPPORT DRAINGS 40 [1016] MAX 7[178] MIN. 3 SHOP FORMED CORNER PANEL DETAIL ONLY NOM. FDS 3TH SEAL PLATE SHOP FORMED TERIOR CORNER 5 8 7[178] MIN. 40 [1016] MAX 3TH SP-0013

11 NOTE: HERE END JOINTS OCCUR IN VERTICAL SUPPORTS, USE BRIDGE FLASHING BEDDED IN NON-CURING BUTYL OVER THE GAP IN SUPPORTS. 1/2 [13] Ă 3 PANEL CLIP AND FASTENER 5 8 NOM. 6 6 MIN. 1/2 [13] Ă MIN. SEE SUPPORT DRAINGS per GN SHTS 10-16x5/8 PER DP3 GN's per GN SHTS POLYURETHANE BLACK PER GN's 'C5' CLOSURE ANGLE (SEE GN FOR BENDING) (TYP) IF ONE LEG IS OVER 6' THE OTHER MUST BE UNDER 6' (TYP) '-0 MAX. UNSUPPORTED (TYP.) 7 MIN. NOM. FDS 3TH SEAL PLATE SHOP NOTCHED, FIELD BEND, TERIOR CORNER PANEL SHOP NOTCHED, DETAIL ONLY FIELD BENDCORNER 3TH SP-0014

12 NOTE: HERE END JOINTS OCCUR IN SEE EL SEE EL VERTICAL SUPPORTS, USE BRIDGE FLASHING BEDDED IN NON-CURING BUTYL OVER THE GAP IN SUPPORTS. SEE SUPPORT DRAINGS PANEL CLIP AND FASTENER CONTINUOUS 1/4 SHIM SEE EL SEE EL SEE NOTE 'B' 3 NOTE 'A' 1/4 REVEALS 1/2 REVEALS (2) 1 REVEALS NOTE 'B' 6'-0 LENGTH 7'-6 LENGTH SEE NOTE 'A' CONTINUOUS 1/4 EACH PANEL ā ITH EQUAL LEGS PANEL NOTCH PANEL CLIP AND FASTENER 5 8 NOM FDS 3TH SEAL PLATE INTERIOR 1/4, 1/2 & 1 REVEALS 3 3TH SP-0015

13 3 COL SP4413 SP VERT. PANEL JTS. 1/2 INTERM. SPLICES BOTTOM EEP IMV HEAD OPENING SP4414-LS AT INTERM. SPLICES SP4414-GP AT VERT. PANEL JTS. PANEL MODULE EL. B/STL FROM SHELF OF TR. TO TOP OF FLASH MIN. 3/8 [10] Ă SS 24 [610]O.C. SEE SUPPORT DRAINGS SHIM AS REQ'D. NBC ROUGH OPENING BACKER ROD & SEALANT NBC FRAME NBC 3 4 3/8 FDS 3TH SEAL PLATE HEAD OPENING - ON MODULE 3TH SP-0017

14 COL x 1 SUPPORTS BOTTOM SP4416 EEPS SP4416-LS SP4417 FROM SHELF OF TR. TO TOP OF FLASH 2 3/8 [10] Ă SP-0019B NOTE: USE ITH DETAIL 2 SEE SUPPORT DRAINGS SHIM AS REQ'D. NBC MIN. 3 4 FASTENERS NBC 5 FRAME NBC SEALANT & BACKER ROD NBC 3 FDS 3TH SEAL PLATE HEAD OPENING - OFF MODULE 3TH SP-0017A

15 /8 Ă TOOL F COORDINATE /INDO DEPTH 2 (MIN) 2 (MIN) BACKER ROD & SEALANT NBC FRAME NBC REVEAL-1/16 PANEL CLIP AND FASTENER 26 F F #10-16x5/8 SD PANEL MODULE 1 8 C 18[457] O.C. 7 8 TOS REVEAL COORDINATE S/INDO DEPTH SS 24 [610]O.C. M8 SHIMS AS REQD SEE SUPPORT DRAINGS SP4413 1/4 FOAM TAPE (/1GAPS) 1 8 NORTON V x 3 LONG 18 O.C. (SPACER) FDS 3TH SEAL PLATE SILL OPENING - ON MODULE 3 CLOSE OFF ENDS OF SILL FLASH, TAB AND SEAL AS REQUIRED TO JAMB CONDITION TO MAKE EATHER TIGHT COL 3TH IMV-0018

16 NOTE : USE ONLY IF IMV INSERT IS REQUIRED ABOVE OR BELO. 5 7/16ā 3 3/8 [10] Ă COL SEE SUPPORT DRAINGS SEE EL SP4413 FIELD CUT ABOUT CENTER LINE 1/2 [13] Ă INDO FRAME (NBC) NOTE 'A' 6'-0 LENGTH 7'-6 LENGTH 26 3 RETURN LEG OF HEM AS REQUIRED TO SUPPORT BACKER ROD & SEALANT: DO NOT CONTINUE PAST NOTE : SEE DETAIL 0017 FOR ON-MODULE JAMB TO HEAD ISO 3/8 [10] Ă PANEL CLIP AND FASTENER PANEL NOTCH 5 8 NOM SEE NOTE 'A' BACKER ROD POLYURETHANE FDS 3TH IMV JAMB OPENING - TRIMLESS /IMV INSERT ROUGH OPENING 3TH SP IMV-0019A

17 0017A NOTE: & 0019C USE ITH DETAIL 3/8 [10] Ă SHIM AS REQ'D. NBC CONTINUOUS 3/16 SPACER TAPE 1/4 1/2 [13] Ă FASTENERS NBC FRAME NBC 26 3 RETURN LEG OF HEM AS REQUIRED TO SUPPORT BACKER ROD & SEALANT: DO NOT CONTINUE PAST SP4416 SP4416-LS SEALANT & BACKER ROD NBC PANEL CLIP AND FASTENER 2 MIN SP FDS 3TH SEAL PLATE JAMB OPENING - CUT PANEL 3TH SP-0019B

18 (ON-MODULE) BASE SP-4414 JAMB SP CONT. BUTYL CONT. 3/8 BEAD 1/2 OF NON-CURING BEAD OF NON-CURING BUTYL SP4414 ON-MODULE BASE CONT. 3/16 SPACER TAPE. 1/4 MARRIAGE BEAD OF NON-CURING BUTYL. JAMB NEEDS BOTTOM PLUGGED /BACKER ROD & SEALANT NOTE: USE ITH DETAIL SP-0019B SP4416 JAMB RETAINER FDS 3TH SEAL PLATE ON-MODULE JAMB/BASE INTERSECTION - CUT PANEL (ISOMETRIC) 0019C