Preliminary. RP-ISO-hermetic EI 30 Fire protection structures Documentation Drawings/Instructions. Fire protection system RP-ISO-hermetic EI 30
|
|
- Alaina Robertson
- 5 years ago
- Views:
Transcription
1 Fire protection structures Documentation Drawings/Instructions Version 06/20 06/' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
2 . General Information.. General terms and conditions General terms and conditions is a system supplier for metal construction. RP systems are intended for use by specialist companies, who are familiar with recognised guidelines and regulations for steel and metal construction work and have a pre-acquired knowledge of the appropriate standards as well as the regulations and practices of the sector. For coatings including pretreatments, recommendations of the coating industry should be considered and the details of the possibilities and conditions should be clarified before placing coating orders with the respective coating companies. The provision of technical information, consultation and proposals are services provided free of charge. They offer non-binding suggestions to planning and implementing companies. It is up to the user, however, to examine such information and decide whether it is suitable for all aspects of his respective application. RP parts are distributed under protection of registered trade marks. The construction of components is tested and certified. When damage results from the use of non-rp components, not only is liability no longer accepted but also the test certificates issued for that construction are no longer valid. When systems are being made from rust-free stainless steels, it should be remembered that not all the accessory components are available in such rust-free stainless steel. When employed in highly corrosive environments, such accessory components should be greased. Special solutions will be built on-site by metal construction specialists taking particular care, since these solutions will not be covered by the usual systematic checks. Equally, components manufactured at the factory must be checked for completeness and proper function before installation. All data, explanations and illustrations in the technical documents were compiled and arranged with the greatest possible care and with the best knowledge. Nevertheless, it is not possible to exclude errors completely. We cannot accept responsibility or liability for the use of proposals, illustrations or data. In all other respects we refer to our terms and conditions of sale and delivery. For technical printing and/or design reasons, it may be the case that illustrations do not always correspond to the indicated standards and standard sizes. reserves the right to make technical changes without advance notice. With the production of new documentation, earlier versions are no longer valid. Version 04/2005 (replaces version 06/2002)..0 06/' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
3 . General Information..2 System advantages Steel advantageous for wide fire doors and interior partitions Protection of people and goods from fire and smoke is gaining ever more importance worldwide. The fire door and fire resistant partition system,, was developed for this purpose with its steel frameworks and fire resistant fillings. It offers the required protection against the effects of fire. Steel is always preferred to other materials for door systems that are in very frequent use. Steel is highly resistant, long-lasting, shockproof and stable. Moreover, with the demand for ever larger components, steel gains ever more significance because of its general static advantages. The outstanding characteristics of steel are reflected in the attachment of the hinges. Steel guarantees the permanent location of the hinges. Lowering of the doors does not occur, which is in contrast to the usual case with other materials, so that readjustment becomes almost unnecessary. s are only useful if they remain functional over their entire service life /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
4 . General Information.2. Table of contens General information. Introduction General terms and conditions..0 System advantages Contens Table of contens.2.0 " Description of system System overview.3.5 Glazing table 2 Application examples Glazing beads.5 2. Door constructions Door constructions Horizontal sections single-leaf door 2. " Horizontal sections double-leaf-door 2.2 " Vertical sections 2.3 " Leaf sash bar, sections Fixed glazing elements 3 Article overview Fixed glazing elements Sections Main profile and glazing bead Main profiles 3..0 Premanufactured profiles Basic profiles RP3400, RP340 and RP Glazing beads Accessories Articles lists Cross section drawings 4. Main profile and glazing bead Main profiles 4..0 Glazing beads and studs Seals Glazing seals, rebate seal and floor seals Fitting scheme 5. Single-leaf doors Single-leaf doors with single and double latch Double-leaf doors Double-leaf doors with single and double latch Closing action overview Normal closing action and panic closing action B /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
5 . General Information.2.2 Table of contens 6 Installation drawings (locks) 6. Single-leaf door locks Mortise dead lock with single latch 6..0 Mortise dead lock with double latch Double-leaf door locks Mortise dead lock with single latch and flush bolt Mortise dead lock with double latch and flush bolt Mortise dead lock with single latch and panic counter lock case Mortise dead lock with double latch and panic counter lock case Installation drawings (hinges) 7. Hinges Screw-on hinge,flat 7..0 Weld-on hinge Installation and drawings. Panic bar Primary leaf..0 Secondary leaf Push bar Primary leaf.2.0 Secondary leaf Installation examples 9. Top door closer Overhead door closer DORMA TS Overhead door closer DORMA TS 93 GSR Other accessories Driver-flap Installation and mounting instructions 0. Mounting instructions Glazing beads and block fillings Assembly instructions Joints and sections Inwardly opening door Joints and sections Outwardly opening door Joints details A, B, C, D Joints detail D covered Joints details E und F Floor seal Automatic floor seal /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
6 ..3 General Information System overview.3 06/' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
7 ..5 Gerneral Information Glazing table Glazing beads Steel glazing beads Glazing thickness (mm) / glazing bead glazing seal outside / / / / / / / / / / / / / / / / / / / / / inside Glazing thickness, galvanization and surface coating tolerances should be considered. So that, if necessary, different combinations may result. Steel glazing beads 5 mm mm 23 mm 2 mm 33 mm 3 mm 25 Studs approx installation dimensions X magazine fed non magazine fed Glazing seals 3mm 3mm 4mm 5mm 6mm 7mm 5mm X * * *) self-adhesive Glazing strips 5mm 2mm /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
8 2. 2. Application examples Door constructions with clipped rebate glazing horizontal sections single-leaf door Cross-section A-A Illustration DIN left outward opening RP3400 RP340 RP340 RP ± 4± Cross-section B-B Illustration DIN right inward opening 4± 4± RP3400 RP34 RP34 RP340 RP Cross-section C RP342 RP mm C A A B B C View from outside 2. 06/' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
9 Application examples Door constructions with clipped rebate glazing horizontal sections double-leaf door Cross-section A-A Illustration DIN left outward opening RP3400 RP340 RP347 RP ± 4± Cross-section B-B Illustration DIN right inward opening 4± 4± RP3400 RP34 4 RP3272 RP Cross-section C RP342 RP322 C C A A S B B S View from outside mm /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
10 Application examples Door constructions with clipped rebate glazing vertical sections Cross-section A-A Cross-section C Cross-section D RP34 RP340 RP342 RP ± 4± Cross-section E RP345 RP34 RP340 RP Cross-section B RP342 A C D RP346 RP342 View from outside mm A E B /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
11 Application examples Door constructions with clipped rebate glazing leaf sash bar, sections Cross-section A Illustration DIN left outward opening RP3400 RP340 RP ± 4± Cross-section B Illustration DIN right inward opening RP3400 RP34 RP Cross-section C A A S RP342 RP346 B C View from outside S B C mm C C /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
12 Application examples Fixed glazing elements with clipped rebate glazing Cross-section A-A Cross-section C-C 05 0 RP342 RP346 0 RP Cross-section B-B RP342 A RP342 0 C C 05 RP RP346 A B C C 0 RP342 0 RP342 B mm /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
13 3. Article overview 3.. Main profiles Art. no. Description Additional info Profile characteristics ) PU PU / bundle Z Z Z Z Z Z Y Y Y Y Y Y RP 3400 RP 340 RP 34 RP 345 RP 346 RP 342 Frame profile t =, mm composite profile: steel, pre-galv. Insulator: PROMATECT Leaf-/ frame profile t =, mm composite profile: steel, pre-galv. insulator: PROMATECT Leaf-/ frame profile t =, mm composite profile: steel, pre-galv. insulator: PROMATECT Bottom profile t =, mm composite profile: steel, pre-galv. insulator: PROMATECT Sash bar profile t =, mm composite profile: steel, pre-galv. insulator: PROMATECT Frame profile t =, mm composite profile: steel, pre-galv. insulator: PROMATECT 2 A = 6,22 cm 2 O = 0,35 m /m G = ca. 6,2 kg/m 4 I y = 36,0 cm 3 W y = 9,9 cm 4 I z = 30,33 cm 3 W = 6,57 cm z 2 A = 7, cm 2 O = 0,366 m /m G = ca. 6,9 kg/m 4 I y = 4,70 cm 3 W y = 0,4 cm 4 I z = 47,30 cm 3 W =,9 cm z 2 A = 7,09 cm 2 O = 0,369 m /m G = ca. 6,9 kg/m 4 I y = 45,40 cm 3 W y = 4,3 cm 4 I z = 47,6 cm 3 W =,90 cm z 2 A = 7,7 cm 2 O = 0,39 m /m G = ca. 7,4 kg/m 4 I y = 53, cm 3 W y = 4,75 cm 4 I z = 59,56 cm 3 W = 2,42 cm z 2 A = 6,3 cm 2 O = 0,349 m /m G = ca. 6,7 kg/m 4 I y = 4,47 cm 3 W y = 0,25 cm 4 I z = 46,49 cm 3 W =,9 cm z 2 A = 5,94 cm 2 O = 0,300 m /m G = ca. 6,0 kg/m 4 I y = 36,6 cm 3 W y = 9,76 cm 4 I z = 30,09 cm 3 W = 6,46 cm z 6m 6m 6m 6m 6m 6m A = cross-sectional area, O = outer peripheral surface, G = Weight, I = area moment of inertia, W = section modulus ) /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
14 Article overview Premanufactured profiles basic profile RP 3400 / RP 340 / RP 34 Art. no. RP 3470 RP 347 RP 3472 Description Additional info Primary / secondary leaf profile composite profile: steel, pre-galv. Insulator: PROMATECT pre-adjusted for locking bar DIN right / DIN left (Profile characteristic values, see RP 3400) Primary / secondary leaf profile composite profile: steel, pre-galv. Insulator: PROMATECT pre-adjusted for locking bar DIN right / DIN left (Profile characteristic values, see RP 340) Primary / secondary leaf profile composite profile: steel, pre-galv. Insulator: PROMATECT pre-adjusted for locking bar PU 3m 3m 3m DIN right / DIN left (Profile characteristic values, see RP 34) *Please note that the primary leaf determines the DIN direction (opening direction)! /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
15 3. Article overview 3..3 Glazing beads Art. no. Description Additional info Profile characteristics ) PU PU / bundle Glazing bead 5 mm steel, pre-galv. Glazing bead mm steel, pre-galv. Glazing bead 23 mm steel, pre-galv. Glazing bead 2 mm steel, pre-galv. Glazing bead 33 mm steel, pre-galv. 2 A = 0,3 cm 2 O = 0,070 m /m G = 0,65 kg/m 2 A = 0,6 cm 2 O = 0,074 m /m G = 0,6 kg/m 2 A = 0,9 cm 2 O = 0,02 m /m G = 0,77 kg/m 2 A =,0 cm 2 O = 0,092 m /m G = 0,7 kg/m 2 A =,22 cm 2 O = 0,02 m /m G = 0,96 kg/m 6m 0 bars/bundle 6m 0 bars/bundle 6m 0 bars/bundle 6m 0 bars/bundle 6m 0 bars/bundle A = cross-sectional area, O = outer peripheral surface, G = weight Glazing bead 3 mm steel, pre-galv. 2 A =,34 cm 2 O = 0,2 m /m G =,05 kg/m 6m 0 bars/bundle ) /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
16 3. Article overview 3.2. Accessories 2xx xxx Art. no. Description Additional info PU Cover plate, profile piece Cover plate, profile 2 piece Key cylinder rosette EV (natural Al) concealed screws piece Door handle, round shaped, EV concealed screws piece Panic bar, stainless steel, right/left primary leaf, leaf-width 300 mm piece secondary leaf, leaf-width 300 mm piece Panic push-bar, stainless steel, r./l. primary leaf, leaf-width 050 mm primary leaf, leaf-width 300 mm piece piece secondary leaf, leaf-width 050 mm secondary leaf, leaf-width 300 mm piece piece Weld-on hinge, steel with straight hinge flaps and ball-shaped bearings piece Middle bolts zinc plated steel, complete, alternatively in place of third middle hinge Single hinge: door hinge piece Useable DIN right or left, flat, with cover cap zinc galvanised steel, protected against unintentional unscrewing adjustable height +/- 4 mm, adjustable sides +/- 3 mm, mounting material included (M6 Screws and blind rivet nuts), Suitable for a maximum door leaf weight of 0 kg with two hinges piece piece /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
17 Article overview Accessories 3xx xxx Seals Art. no. Description Additional info PU X Glazing seal 3 mm, self-adhesive seal profile EPDM, black 00 m X Glazing seal 5 mm, self-adhesive seal profile EPDM, black 00 m Glazing seal 3 mm, seal profile EPDM, black 00 m Glazing seal 4 mm, seal profile EPDM, black 00 m Glazing seal 5 mm, seal profile EPDM, black 00 m Glazing seal 6 mm, seal profile EPDM, black 00 m Glazing seal 7 mm, seal profile EPDM, black 00 m Rebate seal seal profile EPDM, black 00 m Glazing strip 5x5mm 2x5mm 7,62 m 7,62 m /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
18 3. Article overview Accessories 6xx xxx Art. no. Description Additional info PU for steel glazing beadsl Studs with drill bits Studs with drill bits, in magazines 50 pieces 00 pieces = 0 strips Door pin, divided 9x9x20mm piece Door pin 9x9x20mm piece Door pin, panic bar 9x9x75mm piece Door pin, panic push-bar 9x9x75mm piece /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
19 3. Article overview Accessories xx xxx Art. no. Description Additional info PU Electric screwdriver with adjustable stop and bit, with feed for studs in magazines piece 2 00 Drilling jig Aluminium with drill bushes and stop pins, suitable for assembly of the steel door hinges: Set: Part no. 90,440 / 90,450 Single part: Art. No piece /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
20 3. Article overview Accessories 9xx xxx Art. no. Description Additional info PU Automatic floor sealing including accessories and mounting materials primary leaf / secondary leaf mm primary leaf / secondary leaf mm primary leaf / secondary leaf mm primary leaf / secondary leaf mm primary leaf / secondary leaf mm primary leaf / secondary leaf - special measurements on demand For double-leaf doors, two automatic floor seals will be required. PU PU PU PU PU PU /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
21 3. Article overview Accessories 9xx xxx Art. no. Description Additional info Mortise lock PU Single-leaf lock set Action L with back set DIN right / DIN left Panic, shift action B DIN right DIN left PU PU PU Double mortise lock Single-leaf lock set Action L with back set DIN right / DIN left Panic, shift action B DIN right DIN left PU PU PU Mortise lock Double-leaf lock set Panic, shift action B DIN right DIN left PU PU /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
22 3. Article overview Accessories 9xx xxx Art. no. Description Additional info Double mortise lock PU Double-leaf lock set Panic, shift action B DIN right DIN left PU PU Panic counter-lock set DIN right / DIN left PU /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
23 3. Article overview 3.2. Accessories 9xx xxx Art. no. Description Additional info Flush bolt set PU DIN right / DIN left PU /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
24 3. Article overview Accessories 9xx xxx Art. no. Description Additional info PU 2x Set: Door hinge, 2-piece useable DIN right or DIN left flat, with cover cap zinc galvanised steel, protected against unintentional unscrewing adjustable height +/- 4 mm, adjustable sides +/- 3 mm, mounting material included (M6 Screws and blind rivet nuts), suitable for a maximum door leaf weight of 0 kg with two hinges PU 2x Set: Door hinge, 2-piece useable DIN right or DIN left flat, with cover cap zinc galvanised steel, protected against unintentional unscrewing adjustable height +/- 4 mm, adjustable sides +/- 3 mm, mounting material included (M6 Screws and blind rivet nuts), suitable for a maximum door leaf weight of 0 kg with two hinges PU x Riveted middle bolts zinc plated steel, complete, alternatively in place of third middle hinge 2x Weld-on hinge, steel with straight hinge flaps and ball-shaped bearings PU 3x Weld-on hinge, steel with straight hinge flaps and ball-shaped bearings PU /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
25 3. Article overview Accessories 9xx xxx Art. no. Description Additional info PU 2x 2x Handle set, round shaped handle, EV PU 2x 2x Handle set, panic function round shaped handle, EV PU x x Panic bar set, FB 300 PU x x x Push bar set, FB 050 PU x x x Push bar set, FB 300 PU x x x 99 0 Handle set, secondary leaf round shaped handle, EV PU x x x Panic bar set, FB 300 secondary leaf Push bar set, FB 050 secondary leaf Push bar set, FB 300 secondary leaf PU PU PU /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
26 4. Cross section drawings 4.. Main profiles ,, RP 3400 RP , RP 34, RP /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
27 4. Cross section drawings 4..2 Main profiles, 25, RP 342 RP /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
28 4. Cross section drawings 4..3 Prefabricated profiles,, RP 3470 RP , RP /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
29 4. Cross section drawings 4..4 Glazing bead and studs Steel glazing beads -t =,2 mm Studs magazine fed non magazine fed /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
30 Cross section drawings Glazing seals and rebate seal Glazing seals mm self-adhesive mm self-adhesive mm mm mm mm mm Rebate seal Glazing strips Automatic floor seals x5mm x5mm Primary / secondary leaf length [mm] on request For double-leaf doors two automatic floor seals will be required /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
31 5. Fitting scheme 5.. Single-leaf doors Single-leaf lock set ) Single latch lock set, closing action L with back set, DIN right/left Panic-single latch lock set, closing action B, DIN right Panic-single latch lockset, closingaction B, DINleft Double-latch lockset, closingaction L with backset, DINright/left Panic double-latch lock set, closing action B, DIN right Panic double-latch lock set, closing action B, DIN left The set contains the following parts: Latch and deadbolt lock, stainless steel faceplate 270 x 50 x 3 mm, DIN right/left Panic latch and deadbolt lock, stainless steel faceplate 270 x 50 x 3 mm, closing action B, DIN right Panic latch and deadbolt lock, stainless steel faceplate 270 x 50 x 3 mm, closing action B, DIN left Double latch and deadbolt lock, stainless steel faceplate 270 x 50 x 3 mm, DIN right/left Panic double latch and deadbolt lock, stainless steel faceplate270 x 50 x 3 mm, closing action B, DIN right Panic double latch and deadbolt lock, stainless steel faceplate 270 x 50 x 3 mm, closing action B, DIN left Lock casing cover plate25x 243 x.5mm Lock plate without identification, stainless steel, for not Panic Lock plate, stainless steel 270 x 50 x 3 mm (with identification EN 79/25) Espagnolette rod, top, M5 x 900 mm Snap lock, top, 3 mmoverhanging latch Lock plate for switch lock and snap lock, 50 x 50 x 3 mm, stainless steel Handle sets Handle set, bent handle shape, EV anodized (natural Al) Handle set, panic action, bent handle shape, EV anodized Panic bar set, FB 300, stainlesssteel, bent handle shape, EV Push bar set, FB 050, stainlesssteel, bent handle shape, EV Push bar set, FB 300, stainlesssteel, bent handle shape, EV Thesetscontainthefollowingparts: Handle, round shaped handle, EV anodized (natural Al), concealed screws Panic bar primary leaf DIN right/left, leaf width 300 mm, brushed stainless steel Panic bar primary leaf DIN right/left, leaf width 050 mm, brushed stainless steel Panic bar primary leaf DIN right/left, leaf width 300 mm, brushed stainless steel Escutcheon, EV anodized (natural Al), concealed screws Door pin9 x 9 x 20 mm Door pin, divided, 9 x 9 x 20 mm Fixing set for handle sets Hinge sets 2) Screw-on hinge set, st., flat with cap Screw-on hinge set, st., flat with cap, incl. middle bolt Screw-on hinge set, right/left Screw-on hinge set, right/left The setscontain the following parts: Middlebolts Screw -on hinge, steel, flat, with cap special weld-onhinge 3 2 Note that for a single leaf door 3 screw-on hinges =.5 x set are required The alternative is x set /' ) Seechapter 6 for installation 2) Seechapter 7for installation Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
32 5. Fitting scheme 5..2 Single-leaf doors "STADI" automatic floor sealing Automatic floor seal, 772 mm Automatic floor seal, 922 mm Automatic floor seal, 072 mm Automatic floor seal, 222 mm Automatic floor seal, 372 mm Automatic floor seal, length according to specification The set contains the following parts: Automatic floor seal, 772mm Automatic floor seal, 922mm Automatic floor seal, 072mm Automatic floor seal, 222mm Automatic floor seal, 372mm Automatic floor seal, lengthaccording to specification Promatect-Hbar 20x6x25mm door closer DORMA TS 93 on side /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
33 5. Fitting scheme 5.2. Double-leaf doors Double-leaf lock sets for the primary leaf ) Panic-single latch lock set, closing action B, DIN right Panic-single latch lockset, closingaction B, DINleft Panic double-latch lock set, closing action B, DIN right Panic double-latch lock set, closing action B, DIN left The set contains the following parts: Panic lock with latch, stainless steel faceplate 270 x 50 x 3 mm, closing action B, DIN right Panic lock with latch, stainless steel faceplate 270 x 50 x 3 mm, closing action B, DIN left Panic lock with double latch, stainless steel faceplate 270 x 50 x 3 mm, closing action B, DIN right Panic lock with double latch, stainless steel faceplate 270 x 50 x 3 mm, closing action B, DIN left Lock casing cover plate25x 243 x.5mm Espagnolette rod, top, M5 x 900 mm Snap lock, top, 3 mmoverhanging latch Lock plate for snap lock, 50 x 50 x 3 mm, stainless steel Double-leaf lock sets for the secondary leaf ) Panic counter-lockset, DINright/left Flush bolt set, DINright/left *) The set contains the following parts: Panic counter-lock case, DIN EN 25/79, stainless steel faceplate 270 x 50 x 3 mm, bolt 40, DIN right/left Lock casing cover plate 25 x 243 x.5 mm Flush bolt, Stainless steel faceplate 270 x 50 x 3 mm, bolt 40, DIN right/left Cover plate, flush bolt 25 x 5 x.5 mm Top latch lock, 50 x 50 x 3 mm, stainless steel DIN right/left Locking-rod, top, M5 x 2000 mm Locking-rod, bottom, M5 x 950 mm Locking-rod, bottom, M5x 420 mm Floor closing socket Guide bushing Lock plate for snap lock, 50 x 50 x 3 mm, stainless steel *) for the primary leaf a single-leaf lock set should be selected ( ) Handle sets Handle set, bent handle shape, EV anodized (natural Al) Handle set, panic action, bent handle shape, EV anodized Panic bar set, FB 300, stainlesssteel, bent handle shape, EV Push bar set, FB 050, stainlesssteel, bent handle shape, EV Push bar set, FB 300, stainlesssteel, bent handle shape, EV Thesetscontainthefollowingparts: Handle, round shaped handle, EV anodized (natural Al), concealed screws Panic bar primary leaf DIN right/left, leaf width 300 mm, brushed stainless steel Panic bar primary leaf DIN right/left, leaf width 050 mm, brushed stainless steel Panic bar primary leaf DIN right/left, leaf width 300 mm, brushed stainless steel Lock cylinder rosette, EV anodized (natural Al), concealed screws Door pin9 x 9 x 20 mm Door pin, divided, 9 x 9 x 20 mm Fixing set for handle sets ) Seechapter 6 for installation /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
34 5. Fitting scheme Double-leaf doors Handle sets, secondary leaf 99 0 Handle set, one-side, round shaped EV anodized (natural Al) Panic bar set, secondaryleaf, FB 300, stainlesssteel Push bar set, secondaryleaf, FB 050, stainlesssteel Push bar set, secondaryleaf, FB 300, stainlesssteel The sets contain the following parts: Handle, round shaped handle, EV anodized (natural Al), concealed screws Panic bar, secondary leaf DIN right/left, leaf width 300, brushed stainless steel Panic push-bar, secondary leaf DIN right /left, leaf width 050 mm, brushed stainless steel Panic push-bar, secondary leaf DIN right /left, leaf width 300 mm, brushed stainless steel Door pin 9 x 9 x 20 mm Pin EPN 900 for one-side panic bar Pin EPN 2000 for one-side panic push-bar Fixing set for handle sets Hinge sets 2) Screw-on hinge set, st., flat with cap Screw-on hinge set, st., flat with cap, incl. middle bolt Screw-on hinge set, right/left Screw-on hinge set, right/left The setscontain the following parts: Middlebolts Screw -on hinge, steel, flat, with cap special weld-onhinge 3 2 Note that for a single leaf door 3 screw-on hinges =.5 x set are required The alternative is x set "STADI" automatic floor sealing Automatic floor seal, 772 mm Automatic floor seal, 922 mm Automatic floor seal, 072 mm Automatic floor seal, 222 mm Automatic floor seal, 372 mm Automatic floor seal, length according to specification The set contains the following parts: Automatic floor seal, 772mm Automatic floor seal, 922mm Automatic floor seal, 072mm Automatic floor seal, 222mm Automatic floor seal, 372mm Automatic floor seal, length according to specification Promatect-Hbar 20x6x25mm Note: For double-leaf doors, two "automatic sealing" sets will be required! Further accessories (not available to order from RP-Technik) Door closer DORMA TS 93 GSR for double leaf doors (on site) Driver-flap (only required for panic doors, on site) 2) Seechapter 7for installation /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
35 Fitting scheme Closing action overview Normal action and panic action B "Normal action" without panic, with back set Normal position Lock inside inside Handle or knob outside Handle or knob outside The latch (and the upward bolting device) is operated by the handle and can be withdrawn from the back set with the key. The bolt can be drawn back from inside or outside using the key and is simultaneously coupled with the inner and outer handles. When locking the doors, the bolt is drawn back and simultaneously coupled with inner and outer handles. It is then not possible to open the door from inside or outside without a key. "Shift action B" without back set Unlocked Locked outside inside outside inside After operation of the escape function, the door can only be opened again using the handle after coupling the nut with the key circuit. Passage is always possible by operating the handle. Escape direction Escape direction Use For door systems which must on occasions guarantee passage from the inside and outside, whilst at other times must be impassable from outside. In principle, the door can always be opened from the danger side. (Escape door function) Danger side operation (with pre-closed bolt) The door has a handle on the danger side and/or a panic bar. Through operation of the handle and/or panic bar the latch and the pre-closed bolt are withdrawn. The door can then be opened. External operation (with pre-closed bolt) The door has a handle on the outside. With the bolt drawn back the nut is switched to no-load operation. When the bolt is reinserted the nut remains in no-load operation. The nut is only re-engaged after a turn of the key and the door can then be opened using the handle. The bolt can in principle be closed by the key /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
36 Installation drawings locks Single-leaf fire door EI 30 Installation single-latch mortise lock Item a b 2a 2b 3 Art. No Pieces Set compositions see fitting scheme Description Single latch mortise lock, DIN right/left, normal action with back set Single latch mortise lock, DIN right, panic action B Single latch mortise lock, DIN left, panic action B Lock plate 50x3x270 Lock plate 50x3x270 stamped Cover plate 25x243x,5 200 = = = middle of handle above OKFF Section 4± RP3400 RP34 RP34 RP3400 Opening side 40 Bolt 4± ± 0 3 a,b 2a,b /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
37 Installation drawings locks Single-leaf fire door EI 30 Installation single-latch mortise lock Application drawn is DIN left; DIN right is a mirror image M5 a,b M5 2a,b 243 = notch 244 = hole height = hole height OKFF = ,5 * 90,5 * 90,5 * 962,5 * *) All measurement values refer to handle height 050 above OKFF /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
38 Installation drawings locks Single-leaf fire door EI 30 Installation double-latch mortise lock Item a b 2a 2b Art. No Pieces Set compositions see fitting scheme Description Double latch mortise lock, DIN right/left, normal action with back set Double latch mortise lock, DIN right, panic action B Double latch mortise lock, DIN left, panic action B Lock plate 50x3x270 Lock plate 50x3x270 stamped Cover plate 25x243x,5 Snap lock 50x50 Lock plate 50x50 Top locking-rod, 900 mm 200 = = = middle of handle above OKFF Section 4± RP3400 RP34 RP3472 RP3400 Opening side 40 Bolt 4± ± 0 3 a,b 2a,b /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
39 Installation drawings locks Single-leaf fire door EI 30 Installation double-latch mortise lock Application drawn is DIN left - DIN right is a mirror image M5 5 5 ø M5 a,b M5 2a,b 243 = notch 244 = hole height = hole height OKFF = ,5 * 90,5 * ,5 * 962,5 * M5 *) All measurement values refer to handle height 050 above OKFF /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
40 Installation drawings locks Double-leaf fire door EI 30 Installation single-latch mortise lock with flush bolt Item a b 2a 2b Art. No. Pieces Description Single latch mortise lock, DIN right/left, normal action with back set Single latch mortise lock, DIN right, panic action B Single latch mortise lock, DIN left, panic action B Lock plate 50x3x270 Lock plate 50x3x270 embossing Cover plate 25x243x,5 Flush bolt DIN right/left Snap lock 50x50 Lock plate 50x50 Top locking-rod, 2000 mm Bottom locking rod, 420 mm, solid Floor closing socket Guiding plate 24x Cover plate 25x5x,5 Set compositions see fitting scheme 200 = = = middle of handle above OKFF 500 Section 4± RP3400 RP34 RP34 RP347 Opening side 40 Bolt 4± ± a,b 2a,b /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
41 Installation drawings locks Double-leaf fire door EI 30 Installation single-latch mortise lock with flush bolt Application drawn is DIN left - DIN right is a mirror image M5 ø M5 M5 244 = hole height a,b = notch above OKFF 244 = hole height M ,5 5 29, with flush bolt height 500 above OKFF 2a,b 3 OKFF = ,5 * 90,5 * ,5 * 962,5 * *) All measurement values refer to handle height 050 above OKFF /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
42 Installation drawings locks Double-leaf fire door EI 30 Installation double-latch mortise lock with flush bolt Item a b 2a 2b Art. No Pieces Set compositions see fitting scheme Description Double latch mortise lock, DIN right/left, normal action with back set Double latch mortise lock, DIN right, panic action B Double latch mortise lock, DIN left, panic action B Lock plate 50x3x270 Lock plate 50x3x270 embossing Cover plate 25x243x,5 Snap lock 50x50 Lock plate 50x50 Top Espagnolette, 900 mm Flush bolt DIN right/left Snap lock 50x50 Lock plate 50x50 Top locking-rod, 2000 mm Bottom locking-rod, 420 mm, solid Floor closing socket Guiding plate 24x Cover plate 25x5x,5 200 = = = middle of handle above OKFF 500 Section 4± RP3400 RP34 RP3472 RP347 Opening side 40 Bolt 4± ± a,b 2a,b /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
43 Installation drawings locks Double-leaf fire door EI 30 Installation double-latch mortise lock with flush bolt Application drawn is DIN left - DIN right is a mirror image M ø ø M = notch M5 244 = hole height a,b above OKFF 244 = hole height M ,5 5 29, with flush bolt height 500 above OKFF 2a,b 3 OKFF = ,5 * 90,5 * ,5 * 962,5 * *) All measurement values refer to handle height 050 above OKFF /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
44 Installation drawings locks Double-leaf fire door EI 30 Installation single-latch mortise lock with panic counter-lock casing Item Art. No Pieces 2 Set compositions see fitting scheme Description Single latch mortise lock, DIN right, panic action B Single latch mortise lock, DIN left, panic action B Cover plate 25x243x,5 Panic counter-lock casing, DIN right/left Snap lock 50x50 Lock plate 50x50 Top locking-rod, 2000 mm Bottom locking-rod, 950 mm, solid Floor closing socket Closing bar plate 24x 200 = = = middle of handle above OKFF Panic counter-lock casing 050 Section 4± RP3400 RP34 RP34 RP347 Opening side 3 40 Bolt 4± ± /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
45 Installation drawings locks Double-leaf fire door EI 30 Installation single-latch mortise lock with panic counter-lock casing Application drawn is DIN left - DIN right is a mirror image M5 ø M5 M = notch 244 = hole height = hole height 243 = notch 3 OKFF = ,5 * 90,5 * ,5 * 903,5* *) All measurement values refer to handle height 050 above OKFF /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
46 Installation drawings locks Double-leaf fire door EI 30 Installation double-latch mortise lock with panic-counter casing Item Art. No Pieces 2 2 Set compositions see fitting scheme Description Double latch mortise lock, DIN right, panic action B Double latch mortise lock, DIN left, panic action B Cover plate 25x243x,5 Snap lock 50x50 Lock plate 50x50 Top locking-rod, 900 mm Panic counter-lock casing, DIN right/left Snap lock 50x50 Top locking-rod, 2000 mm Bottom locking rod, 950 mm, solid Floor closing socket Guiding plate 24x 200 = = = middle of handle above OKFF Panic counter-lock casing 050 Section 4± RP3400 RP34 RP3472 RP347 Opening side 3 a,b 40 Bolt 4± ± /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
47 Installation drawings locks Double-leaf fire door EI 30 Installation double-latch mortise lock with flush bolt Application drawn is DIN left - DIN right is a mirror image M ø ø M5 M = notch 244 = hole height = hole height 243 = notch 3 OKFF = ,5 * 90,5 * ,5 * 903,5* *) All measurement values refer to handle height 050 above OKFF /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
48 Installation drawings of hinges Screw-on hinge, flat art.no Set no , 2-piece hinge, part no.: with cover cap (adjustable height and sides) View ca. 200 With drilling template art.no.: 200 4± Section RP3400 RP34 6 Threaded pin M Tack welding (as burglary protection) Art.no.: Opening side ca /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
49 Installation drawings of hinges Screw-on hinge, flat art.no Screw-on hinge set fits for all RP door systems Part no Set no Parts list and individual parts per hinge Frame connection Leaf connection Item Description Pieces Item Description Pieces Steel, flat, secured with cap adjustable in height +/- 4 mm, lateral adjustable +/- 3 mm, Galvanised, zinc plated and chrome plated ( order unit = 2 hinges; DIN right/left) Type testing with 2 hinges: maximum door leaf weight 0 kg. (6) M6 blind rivet nut Spacing plate mm (for tolerance reconciliation) Frame hinge support Bush (plastic) M6x20 trilobular countersunk screws Spacing plate 4 mm, for step-faced doors, with RP-ISO-hermetic EI 60 not required Leaf part Spacer bush (plastic) Plug-in axle Stud bolts M5x6 threaded pins Leaf hinge support M5x2 trilobular countersunk screws M6x4 trilobular countersunk screws Centring Pin Cover cap Attention! The plastic bushings [4] + [7] may not be painted, oiled or greased Assembly instructions - Align the doorframe and leaf profile with each other (pay attention to the leaf rebate mass) and with the RP drilling jig. Accessory part no Screw in the M5x6 threaded pin [0] to the break-in protection from above and behind on the leaf part [6] with the leaf open, and tighten firmly. - Press the bush [4] into the frame hinge support [3]. - Press the spacer bush [7] into the leaf profile [6]. - Insert two M6 blind rivet nuts [] into the outer holes on the doorframe profile - Attach the frame hinge support [3] and if necessary feed the spacer plate [2] underneath and secure it using two M6x20 trilobular countersunk screws [5] (for overlying door leaves install spacer plate [6]). Drilling pattern 5 Ø Screw in the leaf hinge support [] using two M5x2 trilobular counter sunk screws [2]. Ø Set the leaf part [6] into the leaf hinge support [], so that the drilled holes in the leaf part [6] and the hinge support [] align (null position). Tighten both parts and insert three threaded M6x4 trilobular counter sunk screws [3] and tighten firmly. - For break-in protection of the leaf hinge support [] bore out the cross-shaped slots in the heads of the M5x2 countersunk screws [2] (alternatively stitch weld in the handle region, see). - Join the frame and leaf supports together and insert plug-in axle [] from above (the safety lug on the pin head must engage with the roller opening). Screw the plug-in pin [] to the stud [9] from below. - Install and complete the door. The leaf can be aligned by loosening the screws [3]. Tighten the screws firmly after aligning. Next, one of the six unused drill holes must he drilled out to 5 mm and a centring pin [4] knocked in to prevent any shifting. (If necessary the door can be readjusted several times). - Clip the cover cap [5] over the upper edge of the leaf part [6]. Additional height and lateral adjustment Support the door leaves (do not damage the existing floor seals). - Laterally remove the cover cap [5]. - Remove the centring pin [4] using pliers (drill-out if necessary). - Loosen the counter sunk screws [3]. - Align the leaves. - Retighten the screws [3]. - Bore out a new 5 mm hole for the centre pin [4] and resecure the leaves by installing a new pin. with tack welding alternative (break-in protection) Drill jig: part no Clip on the cover cap [5]. 4± frame leaf /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
50 7. Installation drawings of hinges 7..3 Weld-on hinge Set no (2-piece) / Set no (3-piece) / Hinge no part. Weld-on hinge Cover cap Steel pin Ø, 97mm long approx Ball bearing Cover cap Value met using spacer piece 200 RP ± RP340 approx. Distance piece used during welding process. The support given by an approximately mm thick folded metal strip, automatically provides the necessary distance to the frame profile and prevents the hinge flaps from damaging the framework's painting when the door is closed. 06/' Load carrying capacity per hinge, approx. 60 kg Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
51 7. Installation drawings of hinges 7..4 Weld-on hinge 4 End cap 5 Ball bearing 4 End cap 2 3 Hinged flaps frame part Steel pin Value met using spacer piece Hinged flaps leaf part RP3400 RP340 Part push against stop edge Part 2 press against holder 6 6 4± Attention: To protect it from corrosion, the ball-bearing should not be used in outdoor areas Welding of the hinges will be more simple, less time-consuming and safer, if the following points are considered: Important advice for overlapping leaf doors! Ensure that a distance of 4 mm is maintained between the leaf frames in the middle overlapping leaf region! Use the spacers!. Hinge part should be joined to hinge part 2 with the stated steel pin 3 and with ball bearing The leaf framework should be inserted into the external framework, using the appropriate spacer pieces in the chambers, and adjusted accurately. Please ensure that the clearance of the doors is at least 4 mm, and that the external edges of the leaves are evenly aligned. 3. The welded-on hinge, part 2, is attached to the external framework and, with the lug of part, pushed to lie parallel against the forward edge of the leaf framework. Insertion of an approx. mm thick folded metal strip (6) automatically provides the necessary gap to the doorframe profile. 4. The hinges are held in place in this situation using fastening clamps and cleanly attached to the accessible longitudinal welds. After this the leaves are opened, the ball-shaped bearing (5) removed, and the counter weld seam is made to the hinge parts. Then the previously attached parts are welded. 5. After cleaning and cooling of the weld seam, the ball bearing (5) is reinserted and the leaf remounted. 6. The leaves are checked and possibly realigned. 7. The plastic end (4) is pushed on once the work is completed. It is recommended that the pin is lightly greased during the final check, part no /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
52 .. Installation drawings Panic bar Primary leaf Drilling pattern 7 35 Drilling pattern Several M5 rivet nuts (4x) will be required for the assembly 39 2,5 92 9, Follow the manufacturer's installation and maintenance guidance. Assembly instructions are attached to the fittings package , Primary leaf panic bar DIN right/left RL.50 mm (FFB=.39 mm) can be shorten BA 4 RP3400 RP347 RP340 RP3400 BA = Attachment axis RL = Crossbar length 00 Surface Brushed stainless steel RL = BA - 67 Panic bar Turning angle 30 Primary leaf..0 06/' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
53 .. Installation drawings Panic bar Primary leaf Drilling pattern see single-leaf door 35 Drilling pattern Several M5 rivet nuts (4x) will be required for the assembly 2,5 Follow the manufacturer's installation and maintenance guidance. Assembly instructions are attached to the fittings package ,5 7 Panic bar, can be shorten Secondary leaf panic bar DIN right/left RL.50 mm (FFB=.39 mm) Primary leaf panic bar DIN right/left RL.50 mm (FFB=.39 mm) BA BA 37 4 Secondary leaf Primary leaf RP347 RP340 RP3472 RP3400 BA = Attachment axis RL = Crossbar length Surface Brushed stainless steel 00 Panic bar Turning angle 40 Secondary leaf (optional) RL = BA - 67 Panic bar Turning angle 30 Primary leaf /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
54 ..2 Installation drawings Panic push-bar Primary leaf Drilling pattern 7 Follow the manufacturer's installation and maintenance guidance. Assembly instructions are attached to the fittings package. Drilling pattern Several M5 rivet nuts (4x) will be required for the assembly ,5 35 = = 6 BA=L-3 5 L Primary leaf Panic push-bar, DIN right/left BA.000 mm (FFB=.074 mm) Primary leaf Panic push-bar, DIN right/lefti BA.250 mm (FFB=.324 mm) can be shorten 4 37 BA RP3400 RP347 RP340 RP Surface Brushed stainless steel V D G BA Attachment axis Base plate Pressure plate Connecting rod BA=L-3 G=BA-50 D=BA-00 V=BA-26 Panic push-bar Turning angle 30 Primary leaf V = Connecting rod D = Pressure plate G = Base plate BA = Attachment axis L = Order length /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
55 ..2 Installation drawings Panic push-bar Secondary leaf Drilling pattern see single-leaf door 7 Follow the manufacturer's installation and maintenance guidance. Assembly instructions are attached to the fittings package. Drilling pattern Several M5 rivet nuts (4x) will be required for the assembly ,5 35 = = 6 BA=L L 2 Panic push-bar can be shorten Secondary leaf Panic push-bar, DIN right/left BA.000 mm (FFB=.074 mm) Secondary leaf Panic push-bar, DIN right/left BA.250 mm (FFB=.324 mm) Primary leaf Panic push-bar, DIN right/left BA.000 mm (FFB=.074 mm) Primary leaf Panic push-bar, DIN right/left BA.250 mm (FFB=.324 mm) FFB 25 BA 37 Secondary leaf 4 37 BA 37 Primary leaf 4 RP3472 RP347 RP347 RP Panic push-bar Turning angle 40 Secondary leaf Surface Brushed stainless steel V D G BA Attachment axis Base plate Pressure plate Connecting rod BA=L-3 G=BA-50 D=BA-00 V=BA-26 Panic push-bar Turning angle 30 Primary leaf V = Connecting rod D = Pressure plate G = Base plate BA = Attachment axis L = Order length /' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0) Fax: (+49)-(0)
RP-ISO-hermetic EI120 fire protection partition system planning and processing manual. fire protection system RP-ISO-hermetic EI120
RP-SO-hermetic E10 RP-SO-hermetic E10 fire protection partition sstem planning and processing manual Edisonstraße, D-59199 Bönen Tel: (+9)-(0)3 83-91 9-0 Fax: (+9)-(0)3 83-91 9 - 1.1 General information
More informationASOLA - THETA ISTRUZIONI DI MONTAGGIO FITTING INSTRUCTIONS INSTRUCTIONS DE MONTAGE INSTRUCCIONES DE MONTAJE MONTAGEANLEITUNG. IMPBAT Rev.
ASOLA - THETA I F E D ISTRUZIONI DI MONTAGGIO FITTING INSTRUCTIONS INSTRUCTIONS DE MONTAGE INSTRUCCIONES DE MONTAJE MONTAGEANLEITUNG IMPBAT08-2 - Rev. 00 "THETA" FITTING INSTRUCTIONS SUB-FRAME Correct
More informationHardware Fitting Accessories Bolts
Lever action flush bolt With slide Width: 19 mm Stroke (a): 25 mm 1 Flush bolt 1 Set of fastening material With lever arm Width: 19 mm Stroke (a): 18 mm 1 Flush bolt 1 Set of fastening material Stainless
More informationFig. 2 DORMA-Glas Stand/Issue 02/03 Seite/Page 1/7
FSW Installation instructions Track rail 75 x 72 mm 1. Ceiling substructure and installation of the track rail (Fig. 1): The track rail must be bolted over its entire length (including the stacking track
More informationBERNINI PANIC DEVICES
BERNINI PANIC DEVICES With EC mark, in compliance with standard EN 25:2008 Exclusive Pininfarina design Complete application adaptability Fast and easy installation Functional safety and reliability Also
More informationHardware Fitting Accessories Door Seals
Areas of application Protection against cold, draught and vermin Reduces light leakage, sound insulation Smoke control, fire resistance Reduces the energy consumption of air conditioning systems (see following
More informationStandard program overview Steel smoke-proof doors
Smoke-proof doors Standard program overview Steel smoke-proof doors Pos. Product 1 RS-1 Steel door (thin rebated) Smoke-proof door in accordance EN 1634-3 / DIN 18095 Dimensions W 625-1350 H 1750-2500
More informationTECTUS. The completely concealed hinge system
TECTUS The completely concealed hinge system It s still design even if there s nothing to be seen! TECTUS This Latin word for concealed signifies SIMONSWERK s newly developed, completely hidden hinge system.
More informationDoor Hinges Drill-in Hinges
Drill-in hinge StarTec Frame part For timber lining frames For rebated doors Maintenance-free friction bearing To use in combination with receiver Max. door weight: 40 kg Knuckle: Ø15 mm Drilling bit Ø7.2
More informationINSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY
INSTALLATION INSTRUCTIONS REPLACING EXISTING DEADBOLT ASSEMBLY A B C L M N D E F G O P Q H I J Tools provided in Amesbury installation kit: (A) door router fixture, (B) doorframe router fixture, (C) ½
More informationBAKA Protect Serie 2000 / Protect. BAKA Protect Series 2000 / The adjustable hinge system for timber entrance doors
Protect Serie 2000 / 4000 Protect BAKA Protect Series 2000 / 4000 The adjustable hinge system for timber entrance doors index BAKA Protect 2D BAKA Protect 2010 2D two-dimensionally adjustable up to 120
More informationPLANE Line PL 901 BASIC
Single Wing T 90 (El2 90-SaC5) Fire Resistant Steel Door PLANE Line PL 901 Plane Optic Fire Protection T90 (El2 90-SaC5) in accordance with DIN EN 1634-1 * Smoke Control RS (S 200) in accordance with DIN
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS ANSI/BHMA - A156.2 BOX CONTENTS CHECK THAT THE CONTENTS OF YOUR BOX ARE CORRECT ACCORDING TO THE MODEL Model 600/605 Model 610/615 Model 620/625 1 Front plate and handle 2 Back
More informationK15.13 FACE FIXED DOOR HINGES K15 DOORS
K15 DOORS K15.13 01.02.2017 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General... K15.13.03 2. 2-part hinge...
More informationASSA FIX DOOR & WINDOW HANDLES ARCHITECTURAL IRONMONGERS SECURITY SPECIALISTS
ASSA FIX DOOR & WINDOW HANDLES ARCHITECTURAL IRONMONGERS SECURITY SPECIALISTS Vinga, handle for windows and glazed doors, Fix 7311 7311 PaTEnT/REGISTERED DESIGn Fix 7311 is a handle for both older and
More informationTITGEMEYER Tf1663GB(0514)1. GETO Megaport II flush rear doors Assembly Instructions
TITGEMEYER GETO Megaport II flush rear doors All rights reserved. The technical data quoted in this catalogue, performance descrip - tions, recommendations and instructions e.g. for the installation of
More informationASS 70 FD folding/sliding door installation guide
ASS 70 FD folding/sliding door installation guide 2 Preparation IMPORTANT These doors should be fitted by competent and trained installers. Please read these instructions thoroughly before beginning the
More informationlight Non-rebated and non-latched single action door (NR) EI30 / EI60
light Non-rebated and non-latched single action door (NR) EI0 / EI60 or EI0/60 UK UK EI0/60 Index Description Page System information Accessories 5 System plans 6-9 System sections - Installation sealing
More informationDICTATOR RTS Tube Door Closer
Tube Door Closer RTS v long DICTATOR RTS Tube Door Closer The "Invisible" Door Closer The DICTATOR RTS tube door closer is built into the door and therefore is as good as invisible. The joint can only
More informationS5 - Window. Outside view. Inside view
S5 - Window Outside view Inside view Dometic Seitz GmbH 1 S5-Window.doc Exterior frame End cap Sealing rubber between exterior frame and wall (Foam rubber) Frame hinge strip Seal between exterior frame
More informationSport-Thieme Handball Goal, 3x2 m, Free-Standing or socketed
Assembly instructions Art.-Nr.: 201 0915 203 4502 Sport-Thieme Handball Goal, 3x2 m, Free-Standing or socketed 0218214 2018 Sport-Thieme GmbH D-38367 Grasleben Germany sport-thieme.com info @sport-thieme.com
More informationaluminium profile system
aluminium profile system 63 AME System aluminium profiles overview series profiles introduction 80x80 x80 x80/180 x Aluminium profiles are provided with longitudinal grooves which can be used in conjunction
More informationNEWS Part. N /0 MINITEC NEWS
NEWS 2009 Part. N 95.0423/0 MINITEC NEWS 2009 1 TABLE OF CONTENT INTRODUCTION CONTENTS 3 END CAP Z WITH HAMMER TAPS 3 END CAP 45X45 VA 4 ANGLE 25 GD-Z 4 ANGLE 45X90 GD-Z 5 ANGLE 90 GD-Z 5 HINGE 19 S 6
More informationShepherd 210A Fingerprint Door Lock Installation Manual V1.1
Shepherd 210A Fingerprint Door Lock Installation Manual V1.1 Hongda USA Inc. 2505 Technology Dr. #2-6A, Hayward, CA 94545, USA Phone: (510) 887-5682 Fax: (510) 372-0487 Email: info@hongdausa.com Website:
More informationINSTALLATION MANUAL FORTRESS SERIES
Guardian Security Structures TEL 1-406-212-2334 EMAIL rg@gssdoors.com WEB www.gssdoors.com FORTRESS SERIES GENERAL INSTALLATION GUIDELINES 1. The door frame is installed using 16 bolt screws 7,5 mm in
More informationFolding sliding doors
Folding sliding doors Standard program overview Folding sliding doors Folding sliding doors single and double-skinned Product Dimensions in mm width/height Leaf thickness Min. headroom Min. lateral projection
More informationASS 70 FD folding / sliding door. Installation Guide
ASS 70 FD folding / sliding door Installation Guide IMPORTANT! These doors should be fitted by competent and trained installers. Please read these instructions thoroughly before beginning the installation.
More informationTECHNOLOGY IN MOTION MACO TILT AND TURN FITTINGS. MULTI POWER fully concealed fittings INSTALLATION INSTRUCTIONS
TECHNOLOGY IN MOTION MACO multi-matic TILT AND TURN FITTINGS INSTALLATION INSTRUCTIONS Key Sash rebate height Sash rebate width Tilt-only window 50 kg Maximum sash weight 2 Contents Applications/processing
More informationBOLOTA 316 OTHER PRODUCT RANGES SERVICE
BOLOTA 316 BOLOTA 316 OTHER PRODUCT RANGES SERVICE INDEX Lever Handles Escutcheons & Bathroom Turns Academy Range Pull Handles Push Plates & Kick Plates Signage Lockcases Cylinders Door Controls Hinges
More informationFABA. Installation Instructions. Conductor Bar System. Publication #FABA-03 3/1/04 Part Number: Copyright 2004 Electromotive Systems
FABA Conductor Bar System Installation Instructions Publication #FABA-03 3/1/04 Part Number: 005-1062 Copyright 2004 Electromotive Systems 1S 100 Z Installation Instructions Contents: Basic Diagram - -
More informationSport-Thieme. Handball Goal. Assembly instruction. 3x2 m, Free-standing with Fixed Net Brackets
Assembly instruction Sport-Thieme Handball Goal Cat.-no.: 115 0953 2392905 239 2918 113 6500 239 2400 239 2413 3x2 m, Free-standing with Fixed Net Brackets Thanks for choosing Sport-Thieme equipment! In
More informationGEZE SLIDING DOOR SYSTEMS
GEZE Perlan 140 Multi-faceted uses with individual accessories The discrete design supports every required room effect and makes the sliding door system with its accessories a guarantee for elegant and
More informationSPECIAL EXTRUSIONS AND ACCESSORIES
PROFILE SYSTEM SPECIAL EXTRUSIONS s no i s u r t xe l a i c eps Import Belgium & Luxembourg Profilex s.a. 4A, Z.I. In den Allern L-9911 Troisvierges Tel: 00352/99 89 06 Fax: 00352/26 95 73 73 www.profilex-systems.com
More informationTools Required. * When installing on a fire door, please see instructions below. *
CL615 Tubular Mortice Latch with Code Free option CL615 Tubular Mortice Latch with Code Free option Number relating to picture Item 1 Front Plate and handle * 2 Back Plate and handle * 3 Neoprene seals
More informationClamping devices 521
Clamping devices 521 522 Product overview Clamping devices Adjustable straps K0001 Hook clamps K0012 Goose-neck straps with long slot K0002 Page 526 Hook Clamps with collar K0013 Page 535 Equipped clamps
More informationINSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET
HIGH EDGE 2 1/4"(57mm) 03079400070 INSTALLATION INSTRUCTIONS FOR INSTALLING T-SERIES EXTRA HEAVY DUTY LEVER LOCKSET IMPORTANT: THIS LOCK IS NON-HANDED. LOCK IS FACTORY PACKED PREADJUSTED FOR 1³ ₄" (45mm)
More informationJ; ('& ): J; )'& ): J; +'& ): J; +(+ ): J;,)& ): 9WXb[ i[j J;9JKI <_n_d] <P%' '& <_n_d] IP 7ii[cXbo 7Z`kijc[dj 9WbYkbWj_ed \ehckbwi
INdex ZERTIFIZIERT 4 INTERIOR DOOR SIMONSWERK TECTUS TE 210 3D for unrebated and rebated, flush-faced quality doors Hinge up to 40 kg Technical Data Load capacity Length (leaf/frame) Width (leaf/frame)
More informationINSTALLATION GUIDE DUOFUSE GARDEN GATE
Installation guide nr.: Version Publication date MOVO- 0008 V2 1/04/2015 INSTALLATION GUIDE DUOFUSE GARDEN GATE The Duofuse wood composite garden gate is much more durable than a wooden gate, and correct
More informationFor Euro grooves and NC International profiles
RIBANTA For Euro grooves and NC International profiles - All accessories are frontally applied - Connection rods are modular and provided already pre-cut to standard sizes - All parts are pre-assembled
More informationInstallation Instructions
TEL: 09 579-8895 FAX: 09 579-2933 EMAIL: sales@nzfiredoors.co.nz NZ Fire Doors Ltd, 89 Gavin Street, Ellerslie, PO Box 12709, Penrose 1642, Auckland, New Zealand. www.nzfiredoors.co.nz Installation Instructions
More informationHardware installation plan
Hardware installation plan WICLINE evo PSK-OZ 160 51001 11.20 for Parallel sliding tilt hardware without force control up to 160 kg www.wicona.com Contents dmissible format sizes, bbreviations...3 Important
More informationMULTI MAMMUT Heavy-duty hardware
TECHNOLOGY IN MOTION www.maco.eu ASSEMBLY INSTRUCTIONS MULTI MAMMUT Heavy-duty hardware Only for use by certified specialists! Not for end users! TILT AND TURNHARDWARE Key/abbreviations Sash rebate height
More informationLift-off hinge. Rising hinge. Standard hinge. Heavy duty hinge. Parliament hinge. Spring hinge. Double action spring hinge. Concealed mortise hinge
Door Hinges Contents Butt hinges Lift-off hinge Rising hinge Standard hinge Heavy duty hinge Parliament hinge Spring hinge Double action spring hinge Concealed hinges Concealed mortise hinge Pivot door
More informationassembly instructions
door opens outwards door opens inwards front cubicle door opens outwards or inwards with side panel seite 1 ensure that the supplied parts are complete by checking the packing list. make sure that tools
More informationCongratulations! You are now on your way to enriching your life with!
C) Using the base point as your reference, measure up 8-1/32 and mark a horizontal line. Measure in from the edge of the door the distance of your backset and mark where the two lines cross. This will
More informationOperating Manual. for CUTTING, PERFORATING, BENDING SLB120
Operating Manual for CUTTING, PERFORATING, BENDING SLB120 31040\B06eng 0896 0 Contents 1. Scope of delivery... 1 2. Technical specifications... 1 3. Applications... 1 4. Commissioning... 2 5. Cutting...
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
More information3. Barrier elements. Barrier posts. Stainles steel
3. Urban Equipment Building Equipment Stainles steel e 3.1 Tubular hoops 216-223 3.2 Access barriers 224-227 3.3 Height restriction barriers 228-231 3.4 Protective railing 232-237 3.5 City fence 238-240
More informationConnector Technology, Shelf Supports Connection Fittings
MODULAR Connection fitting for recess mounting Finish: Burnished : For recess mounting The plate should allways be installed so that the supporting plate butts against the end of the recess. For rapid
More informationED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS
ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS Ver.2 1300 SERIES CONCEALED VERTICAL ROD DEVICE Top Strike Latch Screws Strike Screws Release Plunger Top Latch Plunger Screws
More informationPREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS
PROFILE SYSTEM PRE-ASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS s r ood gni d i l s dna gni t f i l r o f s t neme l e de l bme s s a - er P PREASSEMBLED ELEMENTS FOR LIFTING AND SLIDING DOORS MINITEC
More informationPANIC BARS Marking IN ACCORDANCE WITH 1125:1997/A1:2001
PANIC BARS Marking IN ACCORDANCE WITH 25:997/A:200 Exclusive PININFARINA design Full adaptability in application Quick and easy installation Reliable and safe performance Tested up to 2.000.000 cycles
More informationTable and Furniture Base Fittings Plinth Adjusting Fittings
Adjusting screw with M8 or M thread Rigid, for glide inserts, steel thread Finish/Colour: Black, thread galvanized Version: With acceptance Ø30 mm Thread M8 650.22.381 M 650.22.382 Packing: 1 or 0 pcs.
More informationK13.11 ORCA PANIC EXIT DEVICE K13 DOORS
K13 DOORS K13.11 01.06.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General information... K13.11.03 1.1. Standards
More informationMaterial Packing Brown Grey Pine Black White
RTA Connectors Minifix Zinc alloy For housing: 12 or 18 Bolt hole: Ø 7 or 8, depending on choice of connecting bolt Drilling distance B: Distance from centre of Minifix housing to shelf front edge (24
More informationZero Point Clamping System. ZERO lock BALL lock
Zero Point Clamping System ZERO lock BALL lock kap3 kap 263 Technical information regarding ZERO lock Zero Point Clamping System Application The modularly designed, flexible ZERO lock Zero-Point Clamping
More informationM4 Foot Operated Underpinner Instruction Manual
M4 Foot Operated Underpinner Instruction Manual M4 Walker Rd, Bardon Hill, Coalville, Leicestershire LE67 1TU, England Tel. +44 (0)130 1692, Fax +44 (0)130 16929 e mail sales@framerscorner.co.uk M4 Underpinner
More informationSUMMARY. V-Lock SYSTEM BASIC ELEMENTS ACTUATORS. P V-Lock GENERAL INTRODUCTION 2. P V-Lock FIXING ELEMENTS 10 SUMMARY. P V-Lock ADAPTORS 17
SUMMARY A3 V-Lock SYSTEM P V-Lock GENERAL INTRODUCTION 2 BASIC ELEMENTS P V-Lock FIXING ELEMENTS 10 P V-Lock ADAPTORS 17 SUMMARY P PROFILES 28 P V-Lock ACCESSORIES AND SPARE PARTS 32 1 A3 GENERAL INTRODUCTION
More informationK11.11 ORCA K11 DOORS
K11 DOORS K11.11 01.06.2018 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. General...K11.11.03 1.1. Description and
More informationWPS crew Doors Installation instructions
WPS-132-133 crew Doors Installation instructions ORDER OF INSTALLATION FOR A COMPLETE ENCLOSURE OF A CREW WPS (Weather Protection System) IS AS FOLLOWS: 1. Heater 2. Rear Thresholds - Right Hand & Left
More informationAluminium hinges DORMA LM. October 1999
Aluminium hinges DORMA LM October 1999 DORMA LM Engineered down to the smallest detail adaptable to any profile system The DORMA LM series of aluminium hinges has been developed to give fast, safe and
More informationTechnical Documentation Lift Advanced
Technical Documentation Lift Advanced 1 1 Introduction... 4 2 Basic Information... 5 2.1 Hinge Recommendations... 5 Lift Advanced HF... 5 Lift Advanced HK... 5 2.2 Usage of Aluminium Fronts... 5 19mm Aluminium
More informationK11.13 THREE-POINT LOCKS SERIES 8400 K11 DOORS
K11 DOORS K11.13 THREE-POINT LOCKS SERIES 8400 01.04.2017 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Three-point
More informationXL JOINERY LTD LA PORTE VISTA MODULAR 3 ASSEMBLY INSTRUCTIONS
XL JOINERY LTD LA PORTE VISTA MODULAR 3 2090mm High x 4687mm Wide ASSEMBLY INSTRUCTIONS READ AND UNDERSTAND THESE INSTRUCTIONS FULLY PRIOR TO STARTING INSTALLATION. IT IS STRONGLY RECOMMENDED THAT A COMPETENT
More informationEXIT DEVICE OPERATION FIRE DOOR LABELS, STRIKES AND FRAME SCREWS FOR INFORMATION CALL OR VISIT RITEDOOR.COM
RECORD & LABELS WHAT THIS OWNER'S CAN DO FOR YOU It explains exactly how The Rite Door operates. It explains periodic maintenance requirements necessary to assure reliable operation. It explains simple
More informationAdjustable Feet Castors Accessories for Floor Elements
Adjustable Feet Castors Accessories for Floor Elements Products in this section Levelling Knuckle Feet Threaded spindles for infinite height adjustment Metal or plastic foot plate Knuckle Feet X Compatible
More informationinstallation instructions
installation instructions Easi-Plan WC Frame 820mm with Dual Flush Cistern ref: EPWC-05-1005 Easi-Plan WC Frame 980mm with Dual Flush Cistern ref: EPWC-05-1505 EASI-PLAN installation instructions Parts
More informationBlind, Sliding, Glazed Doors. Fire Proof Closures
Blind, Sliding, Glazed Doors Fire Proof Closures Elite REI 60 - REI 90 - REI 120 Asia REI 30 Fire proof door type Elite has unique characteristics that clearly distinguish it from traditional fire proof
More informationTechnical Information
Technical Information 03.16 page 221 Technical Information This section of the catalogue provides technical information that will help specify, install and maintain Surelock McGill devices and components.
More informationsalto safe 4028 A12 Turn-tilt windows
A12 Turn-tilt windows salto safe 4028 01.09.2013 Waregemstraat 5-9870 Zulte - Belgium - T. 32 9 388 88 81 - F. 32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com salto safe 4028 Contents 1. General
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationSikurExit: panic function multipoint locks for 1- and 2-leaf aluminum and steel doors
SikurExit: panic function multipoint locks for 1- and 2-leaf aluminum and steel doors SikurExit: panic function multipoint locks for 1- and 2-leaf aluminum and steel doors OPERATION 3 point locking mechanism
More informationPrivacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009)
Privacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009) 3/16" HEX BIT #2 ACR BIT 3/8" HEX SOCKET Full-Height (No Switch) Transom (No Switch) Full-Height (With
More informationFS-PORTAL LM Folding - sliding door hardware for aluminium elements with Eurogroove
FS-PORTL LM Folding - sliding door hardware for aluminium elements with Eurogroove... with these decisive advantages:: Top or bottom running with the same profile set Stable running rail with favourable
More informationCongratulations! You are now on your way to enriching your life with! Figure #5. Step 5 Install the Dummy Deadbolt. Step 3 Drill the Door
C) Using the base point as your reference, measure up 8-1/32 and mark a horizontal line. Measure in from the edge of the door the distance of your backset and mark where the two lines cross. This will
More informationED5800 (A) Series. Installation Instructions. Concealed Vertical Rod. Exit Device WARNING
Strike Shim (2) Supplied Strike Plate (3) 10-24 x 3/4" PFHMS (6) 10-24 x 1/2" PFHMS Top Latch TopTube Concealed Vertical Rod Exit Device Important: For use with metal doors only. Device is packed ready
More informationeasypilot Nordic The turn with brake fitting system. Product Catalog 10/2014 in windows Functional Fenestration, Inc.
easypilot Nordic The turn with brake fitting system. in windows Product Catalog 0/0 Winkhaus easypilot Nordic Table of Contents 0-0 Table of contents Pages Pages 9 Pages 0 Page corners drives Pages Pages
More informationShim (2) Supplied. Strike Plate. (3) x 5/8" PFHMS or 10 x 1" PFHWS. Top Latch. (3) x 1/4" PRHMS. Latch Cover. (2) 8 x 3/8" PFH AB SMS
Installation Instructions ED5400 (A) Series ED5470 (B) Series Surface Vertical Rod Exit Devices Strike Angle Must Engage Strike Top Strike 10-24 PFHMS Top Bracket and Strike required for ED5470. Shim (2)
More information. crealco V I S TA F O L D B O T T O M R O L L E R F O L D I N G D O O R Index Legal Disclaimer 4 Profile Identification 5-7 Hardware Identification 8
. crealco V I S TA F O L D B O T T O M R O L L E R F O L D I N G D O O R VISTAFOLD SYSTEM PRODUCT MANUAL 2013 Wispeco (Pty) Ltd, All Rights Reserved Revision: June 2013 . crealco V I S TA F O L D B O T
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
More informationMUTO COMFORT DORMOTION XL 150/80 L 80
MUTO COMFORT DORMOTION XL 150/80 L 80 Installation instructions - Wall mount with DORMOTION ( ) TABLE OF CONTENTS Closer overall Overview Intended use Wall requirements and fittings Safety instructions
More informationHahn KT-R. Butt hinge for plastic doors
Hahn KT-R Butt hinge for plastic doors For explanations of the table, please visit www.dr-hahn.com Service classes Durability Weight of test door Fire resistance Security Corrosion resistance Intrusion
More informationTECTUS - New Versions. New Versions. The completely concealed hinge system
TECTUS - New Versions New Versions The completely concealed hinge system index te 240 3d up to 40 kg 6 te 340 3d up to 80 kg 7 TE 540 3D up to 120 kg 8 TE 640 3D up to 200 kg 9 TE 540 3D A8 up to 100 kg
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS COMPACT LAMINATE TOILET PARTITIONS 1080 DuraLineSeries 1180 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information
More informationInterior Equipment/Shop Fittings
Interior Equipment/ Contents Room and Frontwall Systems DIFLEX Adjusting foot for raised floors Hook-in profile Hook-in profile Eilox SHOPTEC Shopfitting system Wall channel Bracket Column Accessories
More informationInstallation Guide. Evolve bi-fold. 8. Door restrictor- optional p9. 1. Before you start p2. 9. Adjustment. 2. Measuring and surveying p2
Evolve bi-fold Installation Guide 1. Before you start p2 8. Door restrictor- optional p9 2. Measuring and surveying p2 3. Configuration details p4 4. Installation p5 5. Glazing p5 6. Glazing packer details
More informationInstallation for Full Size Polaris Ranger Crew Doors
Installation for Full Size Polaris Ranger Crew Doors Order of Installation: Heater Doors Wiper on to Windshield Windshield Top & Back Panel Note: Most of the steps in these instructions need to be repeated
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review
More informationManufacturing and installation instruction. Solidare Verso. Pergola awning (bottom mounted)
Manufacturing and installation instruction Solidare Verso Pergola awning (bottom mounted) Solidare Verso pergola awning 11-05-2017 * * A T T E N T I O N * * AVZ accepts no liability for any errors in this
More informationTech Sheet. T4 Interior conversion kit how to - fitting instructions. 1. Rear seat belts. 2.
Page 1 of 8 T4 Interior conversion kit how to - fitting instructions Thank you for purchasing our T4 interior conversion kit. This kit will enable you to convert any SWB left hand loading door T4 into
More informationPUSH-PULL-PROPS. and accessories ROBUSTA-GAUKEL GMBH MOUNTING TECHNOLOGY &CO.KG
PUSH-PULL-PROPS and accessories MOUNTING TECHNOLOGY ROBUSTA-GAUKEL GMBH &CO.KG MOUNTING TECHNOLOGY PUSH-PULL-PROPS AND ACCESSORIES INDEX General information...................... 3 Push-pull-prop Type
More information* * 98/9950WDC. Fire-Rated Devices include these. additional components. 1-Point Latch (LBL)
*24739468* 24739468 98/9950WDC Installation Instructions 1-Point Latch (LBL) Fire-Rated Devices include these additional components Metal Edge Wrap required for 60 and 90-minute applications 2-Point Latch
More informationC. Samples for Initial Selection: Manufacturer's color charts showing the full range of colors available.
SECTION 105113 - METAL LOCKERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationInstallation Instructions for Vista Air Vertically Folding Walls
Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.
More informationEDGE-, COVER-, SLIDEAND SEALING PROFILES
PROFILE SYSTEM EDGE-, COVER-, SLIDE- AND SEALING PROFILES s e l i f o r P gn i l aes dna - ed i l S, - r evoc, - egde EDGE-, COVER-, SLIDEAND SEALING PROFILES These profiles are used for groove covering
More informationP USHbutton 500 series
Dimensions 35 60mm 178mm Model 500/505 For use with existing lock 1 6 2 7 3 8 4 9 5 0 1 6 2 7 3 8 4 9 5 0 Features ode Free Entry Mode by turning the slotted button 90 degrees after entering the code (models
More informationinstallation instructions WC Frame 1180mm with Dual Flush Cistern
installation instructions WC Frame 1180mm with Dual Flush Cistern (C,D,E) K F/G N L M 12 13 14 16 1 2 11 A 5 6 Q O Y 3 C 10 E D B P,Z,AA R T V S 4 U 2 No. Part no. Description Quantity A WC Frame with
More informationSection 7 Wooden Door Locks
Section 7 Wooden Door Locks file:///l /CATALOGUES/General J an 2009/c us tom er/purdue/catalog/pic ture Library /Wooden Door/Leggelatc h.jpg SASH LOCKS COMMERCIAL VERSION- CxC 57mm Specification Technical
More informationArriva. Concealed frame doorsets. Installation instructions
Arriva Concealed frame doorsets 1 2 Installation instructions 3 Thank you for choosing Arriva To ensure the installation process is simple and efficient we recommended you read this guide in full before
More informationK12.12 SINGLE LOCKS SERIES 8600 K12 DOORS
K12 DOORS K12.12 01.02.2017 Waregemstraat 5-9870 Zulte - Belgium - T. +32 9 388 88 81 - F. +32 9 388 88 21 - commercial@sobinco.com - www.sobinco.com CONTENTS 1. Door locks series 8600... K12.12.03 1.1.
More information