RP-ISO-hermetic EI120 fire protection partition system planning and processing manual. fire protection system RP-ISO-hermetic EI120

Size: px

Start display at page:

Download "RP-ISO-hermetic EI120 fire protection partition system planning and processing manual. fire protection system RP-ISO-hermetic EI120"

Ezra Lawson
5 years ago
Views:

1 RP-SO-hermetic E10 RP-SO-hermetic E10 fire protection partition sstem planning and processing manual Edisonstraße, D Bönen Tel: (+9)-(0) Fax: (+9)-(0)

2 1.1 General information General introduction RP-SO-hermetic E10 General information supplies sstems for the metal construction industr. RP Sstems are designed to be handled b specialist firms familiar with the generall accepted guidelines and rules of metal construction technolog and and glaing and who can be expected to be familiar with the applicable standards, specifications, and industr best practice. For coatings, including pre-treatment, the procedures recommended b the coating industr must be observed. Details regarding possible applications and conditions should be discussed with the coating plant in question before awarding the coating contract. All technical data, advice and recommendations are voluntar services and intended to provide without obligation proposals to planners and fabricators. The user must, however, examine and decide for theirself whether the proposed products full meet all requirements for his intended application in each individual case. RP products are sold under registered trademark. The also form component parts of tested and approved assemblies. n the case of loss or damage resulting from the use of other products not onl does the compan den all liabilit, but also all testing certificates applicable to the construction lose their validit. With sstems from stainless steel please observe that not all accessor parts are made from stainless steel. For the use in highl corrosive environment these components must be protected b appling grease. Special solutions must be carried out with great care since these are not covered b sstem tests. Equall, workshop made components must be controlled for completeness and function before installation. Ever care has been taken to ensure that the data, explanations and illustrations in the document is accurate and whilst the publishers would be grateful to learn of an error, the regret the can accept no responsibilit. Nevertheless mistakes cannot be entirel excluded. For the use of the suggestions, drawings and data we cannot take an responsibilit or liabilit. Please note also our sales and deliver terms. Because of the constraints printing technolog and/or graphics illustrations ma not alwas correspond to the stated scales and norm sies. reserves the right to undertake technical modifications without prior notice. The publication of new documentation renders invalid all previous versions. Edition Edisonstraße, D Bönen Tel: (+9)-(0) Fax: (+9)-(0)

3 1.1 General information Contents RP-SO-hermetic E10 1 General nformation 1.1 ntroduction and contents General information Contents Application examples.1 Steel profile application 3 Part overview Sstem overview Partiton.1.01 Fire test fotos.1.0 Glaing table Push-in glaing bead sstem.1.03 " Clip-on glaing bead sstem Main profile, steel Main profiles glaing beads Seals Seals Glaing beads Steel glaing beads screws " Edisonstraße, D Bönen Tel: (+9)-(0) Fax: (+9)-(0)

4 .1 General information.1.01 Sstem overview partition RP-SO-hermetic E10 tested dimensions: max. glass dimension W / H 300mm / 100mm.1.01 Edisonstraße, D Bönen Tel: (+9)-(0) Fax: (+9)-(0)

.1 Fire test.1.0 fotos RP-SO-hermetic E10.

5 .1 Fire test.1.0 fotos RP-SO-hermetic E Edisonstraße, D Bönen Tel: (+9)-(0) Fax: (+9)-(0)

6 Glaing table push-in glaing bead sstem RP-SO-hermetic E10 section Glaing bead, steel Glass width glaing bead glaing seal RP 951 in mm 56 6 RP 1637 RP 1591 outside / / / inside Tolerances of glaing thickness, as well as galvaniation and surface coating have to be kept to. Different combinations might possibl result from this. profiles for push-in glaing bead RP 951 RP RP glaing bead, steel glass 18 13mm Prostop (56mm) RP1637 RP mm 5 x 15mm x 15mm Prostop (6mm SZR10) glaing seals Kerafix Flexlit ntumescent strip Kerafix Flexpress 100 1,5 x 50mm 30650* * 35000* 35030* *self adhesive Edisonstraße, D Bönen Tel: (+9)-(0) Fax: (+9)-(0)

7 Glaing table Clip-on glaing bead sstem RP-SO-hermetic E10 section Glaing bead, steel RP 91 Glass width in mm 56 6 glaing bead glaing seal outside / / / inside Tolerances of glaing thickness, as well as galvaniation and surface coating have to be kept to. Different combinations might possibl result from this. profiles for clip-on glaing bead RP 91 RP 916 RP glaing bead, steel Clamping screw glass 18mm 15mm Prostop (56mm) mm 5 x 15mm x 15mm Prostop (6mm SZR10) glaing seals Kerafix Flexlit ntumescent strip Kerafix Flexpress 100 1,5 x 50mm 30650* * 35000* 35030* *self adhesive Edisonstraße, D Bönen Tel: (+9)-(0) Fax: (+9)-(0)

8 Parts overview Main profile, steel RP-SO-hermetic E10 Z Z Z Z Y Y Y Y Part. no. RP 9516 RP 9517 RP 951 RP 916 Description Additional info. sash profile composite profile: length 6000 mm sash profile composite profile: length 6000 mm frame profile composite profile: length 6000 mm sash profile composite profile: length 6000 mm Profile characteristic values 1) A = 7,1 cm O = 0,15 m /m G = 61,07 kg/pc = 99,95 cm W = 19,98 cm = 39,88 cm W = 8,0 cm A = 7,1 cm O = 0,15 m /m G = 61,01 kg/pc = 101,7 cm W =,61 cm = 39,88 cm W = 8,0 cm A = 6,73 cm O = 0,39 m /m G = 58,0 kg/pc = 93,0 cm W = 19,5 cm = 30, cm W = 6,80 cm A = 6,83 cm O = 0,399 m /m G = 6,15 kg/pc = 89,9 cm W = 15,99 cm = 6,70 cm W = 8,90 cm deliver length bar/ bundle A = cross-sectional area, O = outer peripheral surface, G = Weight, = area moment of inertia, W = section modulus 1) Z Z Y Y RP 917 RP 91 sash profile composite profile: length 6000 mm frame profile composite profile: length 6000 mm A = 6,8 cm O = 0,399 m /m G = 6,1 kg/pc = 98,37 cm W = 1,86 cm = 6,65 cm W = 8,89 cm A = 5,9 cm O = 0,350 m /m G = 58,01 kg/pc = 79,3 cm W = 15,5 cm = 30,09 cm W = 6,6 cm Edisonstraße, D Bönen Tel: (+9)-(0) Fax: (+9)-(0)

9 Parts overview Glaing bead, steel RP-SO-hermetic E Part. no. RP 1637 RP 1591 Description Additional info. glaing bead 18 mm glaing bead 13 mm Profile characteristic values 1) A = 1,6 cm O = 0,089 m /m G = 0,99 kg/m A = 1,11 cm O = 0,079 m /m G = 0,87 kg/m deliver length bar/ bundle 8 8 A = cross-sectional area, O = outer peripheral surface, G = Weight, = area moment of inertia, W = section modulus 1) Edisonstraße, D Bönen Tel: (+9)-(0) Fax: (+9)-(0)

10 Parts overview Seals RP-SO-hermetic E10 Part. no. Description Additional info. PU piece m X Glaing seals 3 mm self-adhesive EPDM seal profile, black 100 X Glaing seals 5 mm self-adhesive EPDM seal profile, black Glaing seals m seal profile EPDM, black Glaing seals 7 mm seal profile EPDM, black Kerafix-Flexlit 5 x 15mm, self-adhesive 1 7, Kerafix-Flexlit x 15mm, self-adhesive 1 7, ntumescent strip Kerafix Flexpress 1,5 x 50 mm, self-adhesive Edisonstraße, D Bönen Tel: (+9)-(0) Fax: (+9)-(0)

11 Parts overview Glaing bead, steel RP-SO-hermetic E Part. no Description Additional info. glaing bead 18 mm glaing bead 15 mm Profile characteristic values 1) A = 0,86 cm O = 0,07 m /m G = 0,77 kg/m A = 0,83 cm O = 0,13 /m G = 0,65 kg/m deliver length bar/ bundle A = cross-sectional area, O = outer peripheral surface, G = Weight, = area moment of inertia, W = section modulus 1) Edisonstraße, D Bönen Tel: (+9)-(0) Fax: (+9)-(0)

12 Parts overview Screws RP-SO-hermetic E10 Part. no. Description Additional info. PU piece m clamping screw with coned point clamping screw with coned point, magaine fed Edisonstraße, D Bönen Tel: (+9)-(0) Fax: (+9)-(0)

Preliminary. RP-ISO-hermetic EI 30 Fire protection structures Documentation Drawings/Instructions. Fire protection system RP-ISO-hermetic EI 30

Preliminary. RP-ISO-hermetic EI 30 Fire protection structures Documentation Drawings/Instructions. Fire protection system RP-ISO-hermetic EI 30 Fire protection structures Documentation Drawings/Instructions Version 06/20 06/' Edisonstraße 4, D-5999 Bönen Tel: (+49)-(0)23 3-9 49-0 Fax: (+49)-(0)23 3-9 49-222 . General Information.. General terms