DOMINIQUE POWDER ROOM VANITY

Transcription

1 Page 1 of Dimensions are nominal measurements only. 445 SPECIFICATIONS Recommended Use Basin Material Cabinet Material Colour Capacity Integrated Overflow Plug & Waste Fixing Taphole Domestic, Hotel, and Commercial Vitreous China CLEANING RECOMMENDATIONS 2-pak Gloss Finish Moisture Resistant MDF White 2.5 Litres Yes 32x40mm with Overflow (not supplied) Top siliconed to cabinet, cabinet screwed back to wall NOTE: Fixings Included 1 Taphole-Right Hand Only We recommend the use of soapy water or approved cleaners. This product should not be cleaned with abrasive materials. To see the complete POSH range go to Damage caused by any improper treatment is not covered by the product warranty- refer to Warranty Conditions. Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors. Tech Page Version 1

2 Page 2 of 5 INSTALLATION INSTRUCTIONS - VANITY NOTE Vanity unit must be installed by a qualified tradesman. Please read instructions carefully. Remove all wrapping material, staples and packing straps from the carton. See Hardware and Furniture Parts List for guidance. Be sure you have all parts before you start assembling. Place all wooden furniture parts on a clean and flat soft surface, such as carpet or a rug to prevent from being scratched. IMPORTANT If fixing to timber framed wallls or partitioning, care should be taken to properly reinforce wall. Please check vanity unit for damage before installing. If there is damage, please notify Reece branch where the product was purchased to organise a replacement product. Installation of the vanity unit is deemed as accepting the condition of the vanity unit. PARTS INCLUDED 1. VANITY 1pc 2. SHELF 1pc HARDWARE LIST A. SHELF SUPPORT 4pc

3 Page 3 of 5 INSTALLATION INSTRUCTIONS - VANITY FOR ASSEMBLY First, check the content to make sure that nothing is missing Sort out the parts and fittings as shown. Assemble product step by step It is preferable to rest the product on a soft surface to avoid damage during assembly Do not overtighten screws and fittings Re-tighten all screws and fittings periodically You will need a Phillips Screwdriver to complete this assembly

4 Page 4 of 5 DOMINIQUE MINI WALL BASIN 485MM Ø22 Ø Ø20 Ø Ø Dimensions are nominal measurements only SPECIFICATIONS Recommended Use Material Colour Weight Capacity Overflow Plug & Waste Fixing Taphole Domestic, Hotel, and Commercial Vitreous China White 8kg 2.5 Litres Yes 32 x 40mm with Overflow (not supplied) Included 1 Taphole (Right Hand Only) To see the complete POSH range go to CLEANING RECOMMENDATIONS We recommend the use of soapy water or approved cleaners. This product should not be cleaned with abrasive materials. Damage caused by any improper treatment is not covered by the product warranty- refer to Warranty Conditions. Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors. Tech Page Version 1

5 Page 5 of 5 DOMINIQUE MINI WALL BASIN 485MM INSTALLATION INSTRUCTIONS - MINI WALL BASIN Counter Top Installation Rear of basin is punched for wall fixing bolts. Any counter top installation is recommended against the wall. 1. Use basin as cutout template and cut 20mm in from traced line. 2. Fit selected tapware and waste to basin. Ensure waste is sealed using flexible sealant around the rim. 3. Apply waterproof sealant to rim of basin. 4. Locate basin complete with fittings onto bench top and press firmly all around. 5. Remove excess sealant.