HZ8864A0TX / HZ8864B0TX. Metal/Glass Sliding-Door Display Cabinet. Assembly Instructions PO: Each shelf supports up to lb.

Transcription

1 HZ8864A0TX / HZ8864B0TX Metal/Glass Sliding-Door Display Cabinet Assembly Instructions For assistance with assembly, contact: Southern Enterprises Inc. Customer Service: service@seidal.com PO: Each shelf supports up to lb. Page 1

2 Metal/Glass Sliding-Door Display Cabinet Parts List Please review all parts and hardware before disposing of any packaging. Before beginning assembly, separate each type of hardware. Carefully study the diagrams below and check that you have all parts indicated. Call Customer Service if missing hardware. Using incorrect hardware will cause damage. You may receive extra hardware with your unit. 1) 2PCS 2) 1PC 3) 1PC Legs 4) 1PC Stretcher 5) 1PC Bottom Frame 6) 1PC Left Rear Support 7) 1PC Right Rear Support 8) 1PC Left Front Support 9) 1PC Right Front Support 10) 2PCS Top Frame 11) 3PCS Glass Back Panel 12) 2PCS Glass Side Panels Glass Shelves Glass Doors Page 2

3 A) 16PCS B) 16PCS C) 16PCS Bolts 1/4 x3/4 D) 12PCS Spring Washers E) 4PCS Flat Washers F) 2PCS Glass Pads G) 2PCS L Metal Chips H) 4PCS Plastic Straps I) 4PCS Screws 4x16mm J) 2PCS Bolts 1/4 x1-1/2 K) 2PCS Sliding Wheels L) 4PCS Plastic Anchors Screws 4x38mm Pads **Pre-attached to glass doors** M) 1PC Wrench Care and Cleaning Instructions: Before using, wipe with a clean, dry cloth. Avoid rubbing or scratching the surface with rough or abrasive objects. For replacement parts or questions, please call Customer Service at Assembly Tool Required: No.2 Phillips Screwdriver (Not Included) Page 3

4 Metal/Glass Sliding-Door Display Cabinet Assembly Instructions Note: Do not fully tighten bolts until Step 6 is complete. Step 1: Unit assembly should begin with parts turned upside down for Step 1. Figure 1 Attach Legs (1) to Stretcher (2) using Bolts (A), Spring Washers (B), and Flat Washers (C). Step 2: Attach assembled parts to Bottom Frame (3) using Bolts (A), Spring Washers (B) and Flat Washers (C). Figure 2 Step 3 Attach Left Rear Support (4), Right Rear Support (5), Left Front Support (6), and Right Front Support (7) to Bottom Frame (3) using Bolts (H), Spring Washers (B) and Flat Washers (C). Figure 3 Page 4

5 Step 4 Insert Glass Back Panel (9) along grooves of Left Rear Support (4) and Right Rear Support (5). Figure 4 Step 5 Insert Glass Side Panels (10) along the grooves of Left Rear Support (4), Right Rear Support (5), Left Front Support (6) and Right Front Support (7). Figure 5 Step 6 Attach Top Frame (8) to Left Rear Support (4), Right Rear Support (5), Left Front Support (6) and Right Front Support (7) using Bolts (A). Figure 6 Page 5

6 4 Step 7 Turn assembled unit upright. 5 Stick Glass Pads (D) to brackets on Left Rear Support (4), Right Rear Support (5), Left Front Support (6) and Right Front Support (7). 6 Place Glass Shelves (11) onto brackets of each Support (4/5/6/7). Figure 7 7 Step 8 Attach Sliding Wheels (I) to pre-attached Pads (L) on Glass Doors (12). I Figure 8 I I 8 Step 9 Insert Glass Doors (12) into grooves of Top Frame (8) and Bottom Frame (3). Note: In order to insert doors into grooves, insert top of door first, then insert bottom of door into bottom groove. Figure 9 3 Page 6

7 (E) Screw (K) Anti-tipping Hardware Tip: At least one screw must be directly mounted into a wall stud. Wall anchor is not needed when mounting into a wall stud. (J) Find ideal location on wall and mark location of each mounting hole. Using a power drill and a 3/16 drill bit, drill one 3/16 hole on wall. Note: Make sure not to drill into electrical wiring or plumbing pipes. Insert Wall Anchor (J) into 3/16 hole. Make sure that wall anchors are flush with wall. Tip: It may be necessary to use a hammer to gently tap anchors into place. Attach L Metal Chips (E) in pre-drilled holes on back of Left Rear Support (4) and Right Rear Support (5) using Screws (G). Attach L Metal Chip (E) to Wall Anchor (J) using Screws (K) and Phillips Screwdriver. Attach Plastic Straps (F) to L Metal Chips (E) on wall and Tower. Now your Metal/Glass Sliding-Door Display Cabinet is ready to use! Figure 10 Page 7

8 Parts Replacement Form Customer Information Name Address City/State/Zip Code Phone Number Please indicate where you purchased this item: Store/Website/Catalog Please indicate color/size/style number: Style No Parts Letter Parts Description Quantity Needed Please immediately examine this product carefully. Any request for missing parts or damage replacement must be received within 90 days of your receipt of the product. Replacement, if available, will be honored within this time frame. Parts will not be available for items arriving fully assembled. We do not recommend modifying product(s) and we are not responsible for any damages due to product modification(s). If damages or missing parts are not reported within 90 days of your receipt, we are under no obligation to provide parts or replacement merchandise. For product issues, please contact Southern Enterprises at (toll-free) / (Dallas), Mon-Fri 9am 4pm CST, or us at service@seidal.com. Please ask for customer service representative for issues involving damages or replacement parts. Please ask for technical assistance representative for any issues with product and assembly/construction. Please contact the retailer that you purchased from for returns. Customer Service: service@seidal.com Southern Enterprises, Inc. 600 Freeport Parkway, Suite 200 Coppell, Texas Page 8