Installation Guide for Custom Console Mods Xbox 360 (LED kit)
|
|
- Gyles Higgins
- 6 years ago
- Views:
Transcription
1 Installation Guide for Custom Console Mods Xbox 360 (LED kit) This mod kit works for all versions of the Xbox 360 wireless controllers. This guide is designed to aid you in installing the LED kit from Custom Console Mods you purchased. I try to cover all parts and questions that you may have in this guide. If you have never soldered before, please learn how to first before attempting this installation. You will be working with small parts in this install which after learning proper soldering techniques, will allow for a much smoother and successful installation. Soldering is not hard to do, but takes time to master Warning: Proceed with this installation at your own risk. Any warranty will be void on the controller once you open it. I will not be held responsible for any damage you cause to your controller or any equipment. What is included in this kit: 4 LED s (optional to install) Note: The blue LED s require higher voltage so they may only be bright when using batteries vs. the rechargeable battery pack. The picture shown above with blue LED s is from a controller with battery pack so it does differ. You get more volts from batteries vs. rechargeable batteries. Sometimes this depends on the condition and age of the battery pack. The Red LED s should work fine with the battery pack as they need about the same volts as the green LED s. Also, there have been reports that the blue LED s may not always work with the newer CG type 360 controllers due to the voltage requirements on the CG type controllers. Refer back to the rapid fire install guide to determine the type of controller that you have. Tools you will need: Soldering iron Solder Torx T8 security screwdriver (a small flat head screwdriver will also work) Note: Most of these tools can be purchased at radio shack or you may already have these items in your home.
2 Step 1 - (take apart the controller) Take the controller apart. There are 7 screws to take off. Three on each side of the controller and one hidden one behind the battery pack. There is a small label that the screw is behind. You should use a Torx 8 security screwdriver here, but you can get away with just using a small flat head screwdriver. Just put it to the side of the small pin in the middle. You can also snap the pin in the middle and it will be easier to unscrew. Note: Face the top of the controller down (buttons facing down when opening the controller) or the pieces will fall out. No problem if they do, they just need to be put back. You may need to pry the back off a little as it is a tight fit. 7 Screws
3 Step 2 - (remove stock LED s) There are four stock LED s. They are shown below in the picture. Now this part can be very tricky, especially if you are new to soldering. I will explain to you the best way to remove these LED s however I must stress to proceed at your own risk as I will not be responsible for any damage you cause to your controller. I have found that the best way to remove the stock LED s is to first apply additional solder to both ends of the LED. Be careful when doing this as you do not want to damage any of the circuit traces. Touch one end of the LED and apply some solder to it. There is a small pad underneath these LED s that they are soldered too. What we are trying to do is apply more solder to make contact with the pad underneath which will allow us to heat the pad up more easily. I know this may sound confusing, but trust me. This is the easiest way. Even people that have experience with soldering will have trouble with this. Especially the first go at it. After you applied solder to one end, repeat this for the other. You can also apply a little solder to the side, but be very careful doing so. After you have applied additional solder to the LED, now you can take the LED off. What you want to do is heat up both end of the LED, or the pads underneath. This will allow you to move the LED off from the pad. Use the solder iron to keep heating both sides and lightly push the LED off. What you do not want to do is overheat the pads and break them off. If you do, well like I said; proceed at your own risk. I have done this and it is very difficult, if at all possible, to correct it. Repeat this for all four LED s! Check out my video on how I do this!
4 Step 3 - (Solder new LED s) Carefully take the LED s out of the package. After removing the old LED s you now know how extremely small they are. They can get lost very easily. If you do end up needing more LED s, I sell these separately as well. Now with LED s, you have to be concerned with polarity. If you do not know what this is, don t worry. Polarity basically just means that one side is positive and one side is negative. You must have the LED installed properly in order for the LED to work. Now I have seen some differences with controllers as well as the actually LED s. Usually the LED s have a marking on the back and wherever the line is pointing is the negative side. What we will do is a more unorthodox way of doing it, but it will work. Place the new LED on the pads. Turn on the controller (using the grey rubber pad to make the connection) and then press down on the LED. If it lights up, you got the polarity right. If not, turn it around and try again. Once you get the polarity right, use your soldering iron to heat up the pads underneath while holding the LED down. Use tweezers if needed. Apply a little solder to both ends. Repeat this with all four LED! You may want to test it out each time you solder because if your solder joints are not strong, the LED s may not light up or fall off. Just retry. Check out my video on how I do this as well!
5 You re done! Close the controller back up and turn it on! I hope you enjoy your product form Custom Console Mods and the experience of modding your own controller. Come check us out at and see what other products we will have. You can also see our products on our ebay. You can also see our products on our ebay store
Installation tutorial for Console Customs Xbox 360 Dual Rapid fire Microchip for wired and wireless controllers (all versions)
Installation tutorial for Console Customs Xbox 360 Dual Rapid fire Microchip for wired and wireless controllers (all versions) This tutorial is designed to aid you in installation of a console customs
More informationInstallation tutorial for Console Customs Xbox ONE MaxFire ONE V2 PCB
Installation tutorial for Console Customs Xbox ONE MaxFire ONE V2 PCB This tutorial is designed to aid you in installation of a console customs MaxFire ONE V2 Circuit board in the newer Xbox One Controllers
More informationInstallation tutorial for Console Customs Xbox Mode Dual Button (RFX-5B) Rapid fire Microchip for all Wired and Wireless controllers
Installation tutorial for Console Customs Xbox 360 5-Mode Dual Button (RFX-5B) Rapid fire Microchip for all Wired and Wireless controllers This tutorial is designed to aid you in installation of a console
More informationInstallation tutorial for Console Customs Xbox 360 MaxFire LITE rapid fire Mod Chip.
Installation tutorial for Console Customs Xbox 360 MaxFire LITE rapid fire Mod Chip. This tutorial is designed to aid you in installation of a console customs MaxFire LITE modchip. This tutorial covers
More informationArsenal One Install Instructions for Xbox One Controller
Arsenal One Install Instructions for Xbox One Controller arsenalmod.com Page 1 of 14 Before Proceeding These instructions are for the install of the Arsenal One 28 pin chip for the Xbox One. READ ALL INSTRUCTIONS
More informationA3 Jetta TDI Chip Upgrade
A3 Jetta TDI Chip Upgrade View the online version at http://vw.ogdenlabs.com/kerma.htm I'm writing this article to show how to go about upgrading an A3 Jetta TDI. Please be aware that this is for information
More informationINSTALLATION INSTRUCTIONS
XMOD 23 Mode Rapid Fire Mod Chip INSTALLATION INSTRUCTIONS This tutorial is designed to aid you in the installation of a XMOD Rapid Fire microchip. This installation requires soldering several wires to
More informationXbox One X Project Scorpio Edition Outer Case Replacement
Xbox One X Project Scorpio Edition Outer Case Replacement Removing the external casing for the Xbox One X Project Scorpio Edition gaming console made by Microsoft in 2017. Written By: Ashley Masuda ifixit
More informationtinycylon Assembly Instructions Contents Written by Dale Wheat Version August 2016 Visit dalewheat.com for the latest update!
tinycylon Assembly Instructions Written by Dale Wheat Version 2.1 10 August 2016 Visit dalewheat.com for the latest update! Contents Assembly Instructions...1 Contents...1 Introduction...2 Quick Start
More informationXMOD 18 Mode Rapid Fire Mod Chip
XMOD 18 Mode Rapid Fire Mod Chip INSTALLATION INSTRUCTIONS - PCB version 2 This tutorial is designed to aid you in the installation of a Rapid Fire microchip. This installation requires soldering several
More informationPi-Cars Factory Tool Kit
Pi-Cars Factory Tool Kit Posted on January 24, 2013 Welcome to the factory: Welcome to where you will learn how to build a Pi-Car, we call it the Pi-Cars Factory. We hope that this page contains all you
More informationHow to add a push power button to your XBOX S-Type controller
26.10.2006 Page 1 of 5 http://synapse.wordpress.com How to add a push power button to your XBOX S-Type controller - By Synapse Required Items - XBOX S-Type controller (Wireless ones won t work) Soldering
More informationTutorial Building the Mono Amp Case
Kitronik Ltd Building the Mono Amp Case Tools you will need: Wire cutters/strippers A soldering iron A small cross headed screwdriver A pair of pliers A ruler Included with your case you should find: 16
More informationABC V1.0 ASSEMBLY IMPORTANT!
ABC V1.0 ASSEMBLY Before starting this kit, prepare the following tools: Soldering iron (15-20W will do), flush cutters, no.2 hex screwdriver or allen key and phillips screwdriver. Also briefly go through
More informationHauptwerk Hardware Interface Board Kit for the Universal Midi Encoder Instruction Manual
Hauptwerk Hardware Interface Board Kit for the Universal Midi Encoder Instruction Manual Hauptwerk Hardware 2016 Page 1 Release 1.2 February 2016 Table of Contents Introduction...3 Parts Identification...4
More informationInstallation tutorial for Console Customs PS3 TrueFire Standard Rapid fire Microchip for Sixaxis and Dualshock 3 controllers
Installation tutorial for Console Customs PS3 TrueFire Standard Rapid fire Microchip for Sixaxis and Dualshock 3 controllers This tutorial is designed to aid you in installation of a console customs rapid
More informationArduTouch Music Synthesizer
ArduTouch Music Synthesizer Assembly Instructions rev C Learn To Solder download for free at: http://mightyohm.com/soldercomic The following photos will show you how to solder. But feel free to download
More informationInstructions for Lighting an S Scale Caboose
Instructions for Lighting an S Scale Caboose The S Scale Caboose lighting kit is adaptable for most caboose models of rolling stock including American Flyer (TM) and contains the same components as found
More informationWritten By: Walter Galan
Xbox 360 CPU Heat Sink Replacement CPU heat sink replacement. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 27 INTRODUCTION Use this guide to remove the CPU heat sink from your Xbox
More informationPS4. Ragnarok Flex Modchip Installation Instructions.
PS4 Ragnarok Flex Modchip Installation Instructions Revised 11/25/2013 Tools needed PS4 Controller Viking PS4 Ragnarok Flex modchip DIY Kit (includes mod chip, LED board, and LED lense) Two diodes (included
More informationValue Location Qty Potentiometers C1M Distortion 1 A10k Volume 1. Footswitch 3PDT SW1 1. Jacks 1/4 Mono 2 DC Power 1
Distortion BUILD INSTRUCTIONS Thank you for your purchase of our Distortion+ kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same
More informationValue Location Qty Transistors 2N5485 Q1, Q2, 4 Q3, Q4 2N5087 Q5 1. Trim Pots 250k VTRIM 1. Potentiometers C500k Speed 1. Toggle Switch On/On Vibe 1
P-90 BUILD INSTRUCTIONS Thank you for your purchase of our P-90 kit! We have completely redesigned our entire line of kits to be the most user friendly, while still maintaining their same great sound!
More informationRepairing your Porsche 928 Central Warning System (CWS) controller
Repairing your Porsche 928 Central Warning System (CWS) controller Disclaimer: This procedure is for a 1984 Porsche 928 S controller. Overview: Under the left foot pedal (dead pedal) of the Porsche 928
More informationExecutive Decision Maker Pro Assembly Guide
Assembly Guide 1 Introduction Congratulations with acquiring your Executive Decision Make Pro. This guide attempts to follow you through the entire assembly process and should give you help to find order
More informationWritten By: Arthur Shi
Remove and replace a broken or malfunctioning motherboard for the Google Pixel XL. Written By: Arthur Shi ifixit CC BY-NC-SA www.ifixit.com Page 1 of 21 INTRODUCTION If you're having issues with the overall
More informationSmartDiagnostics V2 Sensor Battery Change Guide
SmartDiagnostics V2 Sensor Battery Change Guide This guide will walk you through changing a battery of a SmartDiagnostics Version 2 sensor, and properly documenting the sensors location, orientation, and
More informationStarship Lighting Kit
The BIG Starship Lighting Kit By Madman Lighting Inc Copyright June 2011, all rights reserved. WARNING: This product contains small parts not suitable for children less than 12 years of age. DO NOT SWALLOW!
More informationInstalling the Onyx Heated Bed
Installing the Onyx Heated Bed This short supplement will guide you through replacing the Phebe I heated bed on your Rostock MAX with the new Onyx heated bed. Your Onyx upgrade kit should include the following
More informationXMOD RAPID FIRE MOD KIT 20 MODES - v4 INSTRUCTIONS
v4 ELECTRONICS XMOD RAPID FIRE MOD KIT 20 MODES - v4 INSTRUCTIONS This tutorial is designed to aid you in the installation of a XMOD Rapid Fire microchip. This installation requires soldering several wires
More informationInstallation Instructions. Oakmont Folding Doors
Before You Start For quick and easy installation of your Oakmont folding door, read these instructions thoroughly. A few minutes of prior planning will make the job easier and ensure years of trouble-free
More informationAtari Lynx I Capacitor Replacement Kit Installation Guide Page 1 of 15. Atari Lynx I Capacitor Replacement Kit Installation Guide
Atari Lynx I Capacitor Replacement Kit Installation Guide Page 1 of 15 Atari Lynx I Capacitor Replacement Kit Installation Guide Thank you for your purchase of an Atari Lynx I capacitor replacement kit
More informationFutura and Caponord dash repair
Futura and Caponord dash repair So... Most of us know about the issues that some have had with their instrument cluster going deal. Some have had it happen while riding while others have had it happen
More informationVisit our ebay store at: ebay username: xbrdepot101
The Complete XBOX 360 Repair Guide With Extreme Uniclamp Fix 2007-2011 Questions, order or product problems, service e-mail: ebay customers: ebayxboxsupport@gmail.com Amazon customers: XBRdepot@gmail.com
More informationPioneer Elite CLD-97 Digital Noise Reduction (DNR) Auto-off Mod DIY Installation Guide
Pioneer Elite CLD-97 Digital Noise Reduction (DNR) Auto-off Mod DIY Installation Guide Background: The CLD-97 laserdisc player has one of the best video quality outputs of any laserdisc player released.
More informationHow to mod a xbox 360 controller
How to mod a xbox 360 controller Copyright 2001. All Rights Reserved Call 1.800.430.5485 or Email: slipgriproducts@earthlink.net How to mod a xbox 360 controller XMOD Modded Controllers, XBOX ONE X, Scorpio,
More informationStandard Kit #1 (3-way switch)
Standard Kit #1 (3-way switch) Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers 3/8 Drill Bit 1/4 Drill Bit Variable
More informationCover Page. Factory Radio Other Documents Available For This Vehicle:
Factory Radio Other Documents Available For This Vehicle: No documents available at this time Adobe Acrobat Reader Printing Tips: 1) Select FLE then PRNT and select your printer. 2) n the print options
More informationEA6500 Antenna Installation Instructions:
Thank you for purchasing the 6 Antenna Mod Kit for your Linksys router. First we will show you how to install the antennas for your router. Next we will teach you how to setup the DD-WRT firmware which
More informationWritten By: justin chadwick
Nintendo DS Lite Buttons Replacement How to remove and replace the Nintendo DS Lite Buttons. Written By: justin chadwick ifixit CC BY-NC-SA www.ifixit.com Page 1 of 10 INTRODUCTION This guide has been
More informationAssembly Instructions
Assembly Instructions For the SSQ-2F 3.1 MHz Rife Controller Board Kit v1.41 Manual v1.00 2012 by Ralph Hartwell Spectrotek Services GENERAL ASSEMBLY INSTRUCTIONS Arrange for a clean work surface with
More informationHarmony Remote Repair
Harmony Remote Repair harmonyremoterepair.com How to install your new Harmony One Front Cover/Touch Screen Important! Before you begin working on your Harmony One, you must discharge any static electricity
More informationAny Questions? Contact us or Alligator Blinkie
Alligator Blinkie The heart of this blinkie is a 12F1822 PIC produced by a company called Microchip. A PIC is a tiny, yet surprisingly powerful little computer. By itself, it can t do much it needs someway
More informationXbox360 Slim Dismantling Instructions
Xbox360 Slim Dismantling Instructions These instructions will show you how to open the console to replace the DVDrom drive, laser and other internal parts. Opening your console will void your warrantee,
More informationLighthouse Beginner s soldering kit
Lighthouse Beginner s soldering kit Kit contains: 1 x 220 ohm resistor (Red, Red, Black) 1 x 82k ohm resistor (Grey, Red, Orange) 2 x 220k ohm resistors (Red, Red, Yellow) 2 x Diodes 1 x Power switch 1
More informationStandard Kit #1 (5-way switch)
Standard Kit #1 (5-way switch) Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers 3/8 Drill Bit 1/4 Drill Bit Variable
More informationIntellivision A/V Mod Installation Guide
Intellivision A/V Mod Installation Guide This document will guide you through installing your Intellivision A/V Mod Kit to your Intellivision I, II, and III game consoles. Installation is basically the
More informationiphone 4S Dismantling Instructions
iphone 4S Dismantling Instructions These instructions will show you how to open the iphone to replace the digitizer, LCD screen and other internal parts. Opening your iphone will void your warrantee, and
More informationGT3B Hack Kit Install Instructions Written By Austin Hutchison
GT3B Hack Kit Install Instructions Written By Austin Hutchison Step 1: Remove 4 screws located on top of the radio. 1 Step 2: There are small plastic latches that also hold the top in place. The easiest
More informationFast Tramp Freighter Lighting Kit
Fast Tramp Freighter Lighting Kit By Madman Lighting Inc Copyright April 2009, all rights reserved. WARNING: This product contains small parts not suitable for children less than 12 years of age. DO NOT
More informationIphone 5 Glass/Lcd REPAIR GUIDE. Version Edition
Iphone 5 Glass/Lcd REPAIR GUIDE Version 1 2016 Edition IPhone 5 Glass/LCd REPAIR GUIDE RiAna Soto Repair Training Specialist rsoto@cellairis.com FOR EVERY REPAIR MAKE SURE TO COMPLETE, INITIAL, AND HAVE
More informationPacific Antenna Wall Wart Tamer 2.0 Kit
Pacific Antenna Wall Wart Tamer 2.0 Kit Description The Wall Wart Tamer lets you utilize those surplus computer and wall pack power supplies as a clean, adjustable voltage, DC power source for radios and
More informationXbox 360 Eject Button Replacement
Xbox 360 Eject Button Replacement Eject button replacement. Written By: Walter Galan ifixit CC BY-NC-SA www.ifixit.com Page 1 of 17 INTRODUCTION This guide will help you replace a damaged or broken eject
More informationDIY Instructions For NGPC Front Light Installation using the Gameboy Advanced SP Front Light
DIY Instructions For NGPC Front Light Installation using the Gameboy Advanced SP Front Light Tools you will need: Phillips Screwdriver Flat head Screwdriver Tri-wing Screwdriver Exacto Knife Soldering
More informationSTEADY HAND GAME WITH LATCHING LED
ESSENTIAL INFORMATION BUILD INSTRUCTIONS CHECKING YOUR PCB & FAULT-FINDING MECHANICAL DETAILS HOW THE KIT WORKS TEST YOUR HAND-EYE COORDINATION WITH THIS STEADY HAND GAME WITH LATCHING LED Version 2.0
More informationStratitec S5202A Snap-in Circuit Breaker
Stratitec S5202A Snap-in Circuit Breaker Replacement This guide will show the user how to remove and replace a SS-001 snap in circuit breaker for a surge protector. Written By: rainbentrott ifixit CC BY-NC-SA
More informationRapid LED NanoCube 28 CF Quad Retrofit
1 Rapid LED NanoCube 28 CF Quad Retrofit Contents Foreword... 1 Outline... 2 Hood Preparation... 2 Attaching LEDs to Heatsink and Wiring LEDs Together... 6 Thermal Grease... 6 Soldering Notes... 7 Tinning
More informationProgrammable Timer Teaching Notes Issue 1.2
Teaching Notes Issue 1.2 Product information: www.kitronik.co.uk/quicklinks/2121/ TEACHER Programmable Timer Index of sheets Introduction Schemes of work Answers The Design Process The Design Brief Investigation
More informationThe TurboGrafx / PC-Engine
The TurboGrafx / PC-Engine There were various versions of the system with various names. The one above is the larger UK/Euro version, Japanese and American systems were much smaller. There was an option
More informationI Click on a link tab to jump to that page. Cover Page
Factory Radio Other Documents Available For This Vehicle: No documents available at this time Adobe Acrobat Reader Printing Tips: 1) Select FLE then PRNT and select your printer. 2) n the print options
More informationInstallation Instructions for FC2 & FC15 Forward Controls for the Super Magna
Installation Instructions for FC2 & FC15 Forward Controls for the Super Magna It is highly recommended that you use a thread lock compound such as Loctite brand on all threads to keep them from vibrating
More information01. Parts. Blink v1.1. Battery Holder x1. Red LED x1 Green LED x1 Blue LED x1. Resistors x3. Battery x1. Blink PCB x1. Push Button Switchers x3
Blink L1 L2 L3 01. Parts Battery Holder x1 Red LED x1 Green LED x1 Blue LED x1 Resistors x3 Learn to Solder Kit Battery x1 L1 L2 L3 Blink PCB x1 S3 Push Button Switchers x3 02. Tools RECOMENDED Soldering
More informationXbox 360 S Hard Drive Bracket Replacement
Replace your HDD's plastic bracket. Rédigé par: David Hodson ifixit CC BY-NC-SA fr.ifixit.com Page 1 de 33 INTRODUCTION Give your Xbox's wiggly hard drive a new bracket to sit in. OUTILS: Metal Spudger
More informationTKEY-1. CW touch key. (no electromechanical contacts) Assembly manual. Last update: May 1,
TKEY-1 CW touch key (no electromechanical contacts) Assembly manual Last update: May 1, 2016 ea3gcy@gmail.com Updates and news at: www.qsl.net/ea3gcy Thanks for constructing the TKEY-1A CW touch key Have
More informationCircuit Board Assembly Instructions for Babuinobot 1.0
Circuit Board Assembly Instructions for Babuinobot 1.0 Brett Nelson January 2010 1 Features Sensor4 input Sensor3 input Sensor2 input 5v power bus Sensor1 input Do not exceed 5v Ground power bus Programming
More informationMicro USB Lamp Kit TEACHING RESOURCES. Version 2.1 DESIGN A STYLISH LAMP WITH THIS
TEACHING RESOURCES SCHEMES OF WORK DEVELOPING A SPECIFICATION COMPONENT FACTSHEETS HOW TO SOLDER GUIDE DESIGN A STYLISH LAMP WITH THIS Micro USB Lamp Kit Version 2.1 Index of Sheets TEACHING RESOURCES
More informationMotorola E815 / E816 Disassembly / Assembly Guide. Ver. 1.1 By Chubbs_WA
Motorola E815 / E816 Disassembly / Assembly Guide Ver. 1.1 By Chubbs_WA April 10, 2007 Table of Contents Disassembly Tools needed 3 Disassembly for dummies 4 Just a note 5 Disassembly of keypad housing
More informationXbox 360 E Motherboard Replacement
Xbox 360 E Motherboard Replacement Replace the entire motherboard in your Xbox 360 E. Written By: Bryce ifixit CC BY-NC-SA www.ifixit.com Page 1 of 17 INTRODUCTION Use this guide if the connections in
More informationInstallation Instructions Precision Sport Shifter
Installation Instructions Precision Sport Shifter 2004 and up Pontiac GTO Part Number 45043 2010, 2005, 2004 by B&M Racing and Performance Products This B&M Precision Sport Shifter has been designed to
More informationElektor Construction Guide TAPIR
Elektor Construction Guide TAPIR The TAPIR is a three-dimensional assembly. To ensure good access to all soldering points, we recommend assembling the kit exactly according to the described sequence. 1
More informationXbox Teardown. Xbox Teardown. Written By: rmarstel. ifixit CC BY-NC-SA Page 1 of 15
Xbox Teardown Written By: rmarstel ifixit CC BY-NC-SA www.ifixit.com Page 1 of 15 INTRODUCTION This is the teardown for the original Microsoft Xbox, not the Xbox 360. TOOLS: Metal Spudger (1) T10 Torx
More informationCanon EOS 5D Mark III Main Board
Canon EOS 5D Mark III Main Board Replacement This guide should help you get to the brains of your favorite workhorse Canon camera. Written By: Matthew Zeller ifixit CC BY-NC-SA www.ifixit.com Page 1 of
More informationINSTANT ROBOT SHIELD (AXE408)
INSTANT ROBOT SHIELD (AXE408) 1.0 Introduction Thank you for purchasing this Instant Robot shield. This datasheet is designed to give a brief introduction to how the shield is assembled, used and configured.
More informationThe Empeg and Riōcar Illumination Kit Installation and User s Manual
The Empeg and Riōcar Illumination Kit Installation and User s Manual Last Updated: October 13, 2005 Table of Contents READ THIS FIRST!!!...1 Introduction to the Installation Process...3 Install the Hijack
More informationIPhone 7 Plus Digitizer/LCD REPAIR GUIDE. Version Edition
IPhone 7 Plus Digitizer/LCD REPAIR GUIDE Version 1 2016 Edition IPhone 7 Plus Digitizer/LCD REPAIR GUIDE LCD AND DIGITIZER REPLACEMENT RiAna Soto Repair Training Specialist rsoto@cellairis.com FOR EVERY
More informationiphone 6 Chargeport REPAIR GUIDE Version Edition
iphone 6 Chargeport REPAIR GUIDE Version 1 2016 Edition IPHONE 6 CHARGEPORT REPAIR GUIDE LCD AND DIGITIZER REPLACEMENT RiAna Soto Repair Training Specialist rsoto@cellairis.com FOR EVERY REPAIR MAKE SURE
More informationLesson 2: Soldering. Goals
Introduction: Its time to learn how to solder. So you have met all the components needed to make a DIY Gamer, now it s time to put it together. Soldering is joining the components to the printed circuit
More informationBill of Materials: Metronome Kit PART NO
Metronome Kit PART NO. 2168325 The metronome kit allows you to build your own working electronic metronome. Features include a small speaker, flashing LED, and the ability to switch between several different
More informationDisassembling Xbox 360 E Top Body
Disassembling Xbox 360 E Top Body Remove the top body of your Xbox 360 E. Written By: Sarah ifixit CC BY-NC-SA www.ifixit.com Page 1 of 12 INTRODUCTION You will need to remove the top body of your Xbox
More informationEscrito por: Kevin Hua
Microsoft Surface Battery Pack Replacement Replace the battery pack of your Microsoft Surface. Escrito por: Kevin Hua ifixit CC BY-NC-SA es.ifixit.com Página 1 de 8 INTRODUCCIÓN This repair guide will
More informationThe build should take around 2 to 3 hours. However, by leaving yourself more time you can go at a relaxed pace and be sure not to miss anything.
Before We Start Before we jump into building your Picade, make sure you have everything to hand. I know you're eager to jump right into the construction, but we need to get set up properly first! 1. Prepare
More informationTemperature activated switch
Build instructions, circuit explanation and example applications Issue 1.5 Product information: www.kitronik.co.uk/quicklinks/2113/ TEACHER Temperature activated switch Introduction About the project kit
More informationMustang Door Sill Plates Installation Guide
Mustang Door Sill Plates Installation Guide The below installation instructions work for the following products: 1994-2004 Ford Mustang Steeda Polished Door Sill Plates Congratulations on purchasing a
More informationQUANTUM Qflash T2 / X2 OPERATING INSTRUCTIONS
QUANTUM Qflash T2 / X2 OPERATING INSTRUCTIONS 1.0 DESIGNATIONS T2 AND X2 1. Removable Reflector, two positions Normal and Wide angle. 2. Flash-tube 2A. Modeling Lamp (for Model X2 only) 3. Bounce Head,
More informationTI-84 Plus Silver Edition Individual Key Replacement
TI-84 Plus Silver Edition Individual Key Replacement This guide will show you how to replace an individual key on your TI-84 Plus Silver Edition. Written By: Kale McKinney ifixit CC BY-NC-SA www.ifixit.com
More informationExplorer Wiring Kit (assembled)
Explorer Wiring Kit (assembled) For Vintage, Firestorm & Standard Series Please Read All Instructions Before Beginning. Tools you will need: Soldering Iron (35 watt preferably) Solder Wet Sponge Wire Clippers
More information3 flashing red lights on xbox 360 fix
3 flashing red lights on xbox 360 fix Three flashing red lights mean that the Xbox 360 console or its power supply has a hardware problem. To find out. Start the repair process online. If your. My xbox
More informationRédigé par: oldturkey03
Xbox 360 Power Supply Teardown To teardown the power supply was a lot easier than I previously have been lead to believe. There is no glue involved, no hidden screws and it is straight forward. Rédigé
More informationLPF-9B Nine band low pass filter module kit ( meters)
LPF-9B Nine band low pass filter module kit (80-60-40-30-20-17-15-12-10 meters) Assembly manual Last update: March 1, 2018 ea3gcy@gmail.com Most recent updates and news at: www.ea3gcy.com Thanks for constructing
More informationNEW WAVE CV GENERATOR Build Document last updated september 2017 for PCB version 1.0
NEW WAVE CV GENERATOR Build Document last updated september 2017 for PCB version 1.0 The New Wave is a Control Voltage Generator. It has two LFO's (low frequency oscillators) and four different output
More informationAssembly Instructions for the 1.5 Watt Amplifier Kit
Assembly Instructions for the 1.5 Watt Amplifier Kit 1.) All of the small parts are attached to a sheet of paper indicating both their value and id. 2.) Leave the parts affixed to the paper until you are
More informationPS3 CONTROLLER 4 BLINKING LIGHTS
08 July, 2018 PS3 CONTROLLER 4 BLINKING LIGHTS Document Filetype: PDF 535.06 KB 0 PS3 CONTROLLER 4 BLINKING LIGHTS My Ps4 controllers where just unsynching everyday until I tried these methods. - Ps3 Controller
More informationS&T GeoTronics LLC Open DSKY with AGC Assembly Instructions
S&T GeoTronics LLC Open DSKY with AGC Assembly Instructions First, make sure you have all the required components: HARDWARE Qty Item 1 DSKY PCB v1.0d 1 Arduino Nano 1 VA RTC 1 IMU 1 Buck StepDown 1 SKM53
More informationSega CD 2 CMOS Battery Replacement Guide Page 1 of 7. Sega CD 2 CMOS Battery Replacement Guide
Sega CD 2 CMOS Battery Replacement Guide Page 1 of 7 Sega CD 2 CMOS Battery Replacement Guide Thank you for your purchase of a Sega CD 2 CMOS battery replacement kit from Nintendo Repair Hut. We appreciate
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2004 2008 Ford F-150 XLT, FX4, & Lariat Pre-wired without side signals Pre-wired with side signals Without side directional lights, see page 2 With side directional
More informationINSTALLATION MANUAL FRONT. See pages 2 and 3 of this manual for configuration options. Level of Difficulty. Product Photo (center section only)
INSTALLATION MANUAL FRONT Level of Difficulty Moderate Product Photo (center section only) All hardware listed below will be provided with the bumpers center section. Additional hardware will be supplied
More informationInstalling Your Electronic Deadbolt
Ultra Security Plus Electronic Deadbolt Installation Instructions http://www.hberger.com/video-gallery/electronic-deadbolt New Installation Lock Location Preparation (Skip this section if you door has
More informationSignal Mirror Installation Instructions Toyota Tacoma
Signal Mirror Installation Instructions 2005-2015 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0115-0 Rev. A4 (3/11/15), BTV 2005 Muth Mirror Systems, LLC Page 3 of 12PplPage 3 of 12
More informationW7MRI's Anderson Powerpole. Power Hub
W7MRI's Anderson Powerpole Power Hub This PDF is provided by K7JM at http://radio.mcdougallshome.net Don, W7MRI made up a nice small circuit board that holds 7 pairs of Anderson Powerpole connectors to
More informationVinyl Gazebo Instructions
P a g e 1 Vinyl Gazebo Instructions 10 Vinyl Gazebo Shown Thank you for the purchase of your New Gazebo. Depending on the size of your Gazebo, installation can usually be completed in 1 to 2 days. These
More informationWater Level Meter: Op Instructions
Equipment Check 1. Turn sensitivity switch fully clockwise. Notes: 1. Clockwise rotation of sensitivity swsitch turns meter on and increases sensitivity. 2. Always set switch to highest sensitivity position,
More information