Xbox Teardown. Xbox Teardown. Written By: rmarstel. ifixit CC BY-NC-SA Page 1 of 15

Transcription

1 Xbox Teardown Written By: rmarstel ifixit CC BY-NC-SA Page 1 of 15

2 INTRODUCTION This is the teardown for the original Microsoft Xbox, not the Xbox 360. TOOLS: Metal Spudger (1) T10 Torx Screwdriver (1) T15 Torx Screwdriver (1) T20 Torx Screwdriver (1) ifixit CC BY-NC-SA Page 2 of 15

3 Step 1 Xbox Teardown Start with your Xbox unplugged and sitting on a flat, stable surface. Step 2 Flip the Xbox over and pry off the rubber feet with a metal spudger. ifixit CC BY-NC-SA Page 3 of 15

4 Step 3 Peel back both the silver sticker and the white barcode sticker to reveal two additional screws. ifixit CC BY-NC-SA Page 4 of 15

5 Step 4 Use a T20 Torx screwdriver to remove the four screws located under the rubber feet you just removed as well as the two screws from beneath the stickers removed in the previous step. Step 5 Use a metal spudger to pry the side of the top shell away from the bottom of the Xbox. Use your fingers to lift the bottom shell of the Xbox away from the top shell. It may be helpful to have a second person lift the bottom shell off while you pry the edges of the top shell away from the bottom shell. ifixit CC BY-NC-SA Page 5 of 15

6 Step 6 Once the bottom shell is no longer attached, carefully turn the Xbox right-side-up and lift off the top shell. ifixit CC BY-NC-SA Page 6 of 15

7 Step 7 Move the grey ribbon cable out of the way in order to remove the three 3 mm screws using T10 Torx screwdriver. They are located on the upper right corner, lower right, and lower left corners of disk drive. The screw on the lower left corner of the disk drive is not in the hole that it appears to be in, but rather just closer to the corner. ifixit CC BY-NC-SA Page 7 of 15

8 Step 8 Lift the hard drive storage unit out of the Xbox. It should come right out. Take the power cable out of the track around the hard drive so that the unit will come out easier. Step 9 Use a T15 Torx screwdriver to remove four 3.37mm screws from both sides of the hard drive. Remove the plastic housing from the hard drive. It does have some clips on it, but it should come right off. ifixit CC BY-NC-SA Page 8 of 15

9 Step 10 Unplug both the ribbon cable and power cable from hard drive. They are in there pretty tightly, so this may take some effort. Step 11 Remove the disk drive. It should come right out. Unplug the ribbon cable and yellow cables from back of disk drive. ifixit CC BY-NC-SA Page 9 of 15

10 Step 12 Pry back the black plastic tabs around the disk drive in order to remove it from its housing. Once removed, set the drive aside. Step 13 Unplug the multi-colored power cord from the motherboard. It can be plugged in very tight, so it may take some effort to unplug it. ifixit CC BY-NC-SA Page 10 of 15

11 Step 14 Using T10 Torx screwdriver, remove two 3mm screws from the power supply board. Step 15 Remove the power supply and set it aside. It should lift right out. ifixit CC BY-NC-SA Page 11 of 15

12 Step 16 Unplug the bundle of yellow cables as well as the rainbow cord from the motherboard. Step 17 Remove eleven 3mm screws from motherboard, using a T10 Torx screwdriver. Refer to the picture to find all eleven. Unplug the power cable attached to the fan. ifixit CC BY-NC-SA Page 12 of 15

13 Step 18 Remove the motherboard from the Xbox. As long as all of the screws are out and the fan is disconnected, it will lift out easily. Step 19 Pry the plastic fan clips away from the fan base and remove the fan. This may take a little effort, as the clips are pretty stiff. Beware, the fan will be filthy. ifixit CC BY-NC-SA Page 13 of 15

14 Step 20 Using a T10 Torx screwdriver, remove two 3mm screws from each of two controller sockets. Take the sockets out by pulling back and up at the same time. Step 21 Congratulations, your Xbox is now completely dismembered. To reassemble your device, follow these instructions in reverse order. ifixit CC BY-NC-SA Page 14 of 15

15 This document was last generated on :00:35 AM. ifixit CC BY-NC-SA Page 15 of 15