AND8312/D. A 36W Ballast Application with the NCP5104
|
|
- Theodore Haynes
- 5 years ago
- Views:
Transcription
1 A 6W Ballast Application with the P50 Prepared by: Thierry Sutto This document describes how the P50 driver can be implemented in a ballast application. The scope of this application note is to highlight the P50 driver and not to explain or detailed how to build electronic ballast. The P50 is a high voltage power MOSFET driver providing two outputs for direct drive of N-channel power MOSFETs arranged in a half-bridge configuration with only one input. It uses the bootstrap technique to insure a proper drive of the High-side power switch. The driver works with one input to accommodate half-bridge topology with a fixed dead time of 50 ns. Demo Board Specification Input range : 85 Vac - 5 Vac OR 8 Vac - 65 Vac Ballast Output Power : 6 W (type PL-L 6W) Pre-Heating Current : 95 ma Pre-Heating Time : second Nominal Current : ma NOTE: BEFORE PLUGGING IN THE DEMO BOARD, MAKE SURE THE JUMPER IS ON THE CORRECT POSITION: IF J IS USED, THEN Vin MUST BE LOWER THAN 5 Vac. Detailed Operation The lamp ballast is powered via a half bridge configuration. The power MOSFETs are driven with the P50 driver. The driver is supplied by the V CC rail, and the high side driver is supplied by the bootstrap diode: when the low side power MOSFET (Q) is switched ON, the BRIDGE pin is pulled down to the ground, thus the capacitor connected between BRIDGE pin and VBOOT pin is refuelled via the diode D and the resistor R5 connected to V CC. When Q is switched OFF the bootstrap capacitor C6 supplies the high side driver with a voltage equal to V CC level minus the D forward voltage diode. Given the P50 architecture, the driver copies the input signal to the high side driver, then it generates a fixed dead time (50 ns) before toggling the low side driver when the input pin level changes. Figure. Dead Time Between the High and Low-Side Driver Semiconductor Components Industries, LLC, 007 November, Rev. 0 Publication Order Number: AND8/D
2 IN_HI DRV_HI IN_LO DRV_LO Time ( ms/div) Figure. Input Output Timing Diagram Tube Voltage (00 V /div) Tube current (0.5 V /div) Tube Power (50 W/div) Tube average power = W Figure. Tube Signals
3 Figure. Demo Board Schematic R C C R6 68k R 7k R 7k R0 k R5 k R OR R TRIG CVOLT DIS THR Q VCC C U TLC555C D 5V.W VCC IN SD C7 00 F C 0 F C 7 F 00V C 7 F 00V F T500mA CON J C0 00pF C6 R 8k W R 8k W R k VBOOT DRV_HI Bridge DRV_IO U P50 C 7 F C5 00nF R5 0R D N96 C6 00nF R6 0R R8 0k PT Q IRF80LC Q IRF80LC C5 6.8nF R9 0k R7 0R R 90k D6 N96 C 0pF/00V D5 N L.mH B BALLAST kv C8 0nF 00V C7 0nF 00V
4 Figure 5. PCB Printout: Top and Bottom View
5 BILL OF MATERIAL Part Type Designator Manufacturer Description Connector B, J - Connector 7uF/00V C, C Panasonic M Series 0pF C0 Generic Capacitor 0nF C Generic Capacitor C, C - Capacitor 0pF /00V C Generic Capacitor 6.8nF/kV C5 Generic Capacitor C6 - Capacitor 00uF C7 Generic Capacitor 0uF C Generic Capacitor.7uF/50V C Generic Capacitor 00nF C5 Generic Capacitor 00nF C6 Generic Capacitor 0nF/00V C7, C8 Generic Capacitor 0pF C9 Generic Capacitor BZX85C5V D Generic 5V Zener diode N96 D, D5, D6 ON Semiconductor Fast Recovery rectifier BZX85C5V D Generic 5V Zener diode T500mA F Generic Fuse US-jumper J - Jumper for US main supply only.mh L VOGT VOGT 5-0 DF06M PT - 600V Diode Bridge IRF80LC Q, Q IRF Low Charge N-Channel MOSFET BC57B Q Generic NPN transistor k R Generic Resistor k R0 Generic Resistor 7k R Generic Resistor 7k R Generic Resistor 5k R Generic Resistor 90k R Generic Resistor k R5 Generic Resistor 68k R6 Generic Resistor R - Resistor 8k/W R, R Generic Resistor W power type 0R R5, R6, R7 Generic Resistor 0k R8, R9 Generic Resistor TLC555C U Texas Instrument CMOS 555 timer P50 U ON Semiconductor P50 5
6 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 56, Denver, Colorado 807 USA Phone: or Toll Free USA/Canada Fax: or Toll Free USA/Canada orderlit@onsemi.com N. American Technical Support: Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: Japan Customer Focus Center Phone: ON Semiconductor Website: Order Literature: For additional information, please contact your local Sales Representative AND8/D
AND8295/D. A 36W Ballast Application with the NCP5106B
A 36W Ballast Application with the NCP506B Prepared by: Thierry Sutto This document describes how the NCP506B driver can be implemented in a ballast application. The scope of this application note is to
More informationFigure 1. NCP5104 Evaluation Board
P50 6 W Ballast Evaluation Board User's Manual EVAL BOARD USER S MANUAL Introduction This document describes how the P50 driver can be implemented in a ballast application. The scope of this evaluation
More informationAND8285/D. NCP1521B Adjustable Output Voltage Step Down Converter Simulation Procedure SIMULATION NOTE
NCP1521B Adjustable Output Voltage Step Down Converter Simulation Procedure Prepared by: Bertrand Renaud On Semiconductor SIMULATION NOTE Overview The NCP1521B step down PWM DC DC converter is optimized
More information1. DEFINE THE SPECIFICATION 2. SELECT A TOPOLOGY
How to Choose for Design This article is to present a way to choose a switching controller for design in the s Selector Guide SGD514/D from ON Semiconductor. (http://www.onsemi.com/pub/collateral/sgd514d.pdf)
More informationLow Capacitance Transient Voltage Suppressors / ESD Protectors CM QG/D. Features
Low Capacitance Transient Voltage Suppressors / ESD Protectors CM1250-04QG Features Low I/O capacitance at 5pF at 0V In-system ESD protection to ±8kV contact discharge, per the IEC 61000-4-2 international
More informationAND8450/D. NCV7680 LED Driver Linear Regulator Performance APPLICATION NOTE
NCV7680 LED Driver Linear Regulator Performance APPLICATION NOTE Introduction The NCV7680 is an automotive LED driver targeted primarily for rear combination lamp systems. A high input voltage to this
More informationASM1232LP/LPS 5V μp Power Supply Monitor and Reset Circuit
5V μp Power Supply Monitor and Reset Circuit General Description The ASM1232LP/LPS is a fully integrated microprocessor Supervisor. It can halt and restart a hung-up microprocessor, restart a microprocessor
More informationAND9100/D. Paralleling of IGBTs APPLICATION NOTE. Isothermal point
Paralleling of IGBTs Introduction High power systems require the paralleling of IGBTs to handle loads well into the 10 s and sometimes the 100 s of kilowatts. Paralleled devices can be discrete packaged
More informationNTNUS3171PZ. Small Signal MOSFET. 20 V, 200 ma, Single P Channel, 1.0 x 0.6 mm SOT 1123 Package
NTNUS7PZ Small Signal MOSFET V, ma, Single P Channel,. x.6 mm SOT Package Features Single P Channel MOSFET Offers a Low R DS(on) Solution in the Ultra Small. x.6 mm Package. V Gate Voltage Rating Ultra
More informationMPSL51. Amplifier Transistor PNP Silicon MAXIMUM RATINGS. THERMAL CHARACTERISTICS
Amplifier Transistor PNP Silicon MAXIMUM RATINGS Rating Symbol alue Unit Collector Emitter oltage CEO dc Collector Base oltage CBO dc Emitter Base oltage EBO 4. dc Collector Current Continuous I C 6 madc
More information434MHz LNA for RKE Using the 2SC5245A Application Note
434MHz LNA for RKE Using the 2SC5245A Application Note http://onsemi.com Overview This application note explains about ON Semiconductor s 2SC5245A which is used as a Low Noise Amplifier (LNA) for RKE (Remote
More informationEVALUATION BOARD FOR STK N, 120N, 140N. Phenol 1-layer Board) Figure 2. STK NGEVB Figure 3. STK NGEVB Figure 4.
STK44-NGEVB, STK44-1NGEVB, STK44-14NGEVB STK44-N Series Evaluation Board User's Manual EVAL BOARD USER S MANUAL Thick-Film Hybrid IC for use used in from 6 W to 18 W 1ch class AB audio power amplifiers.
More informationPCS2P2309/D. 3.3V 1:9 Clock Buffer. Functional Description. Features. Block Diagram
3.3V 1:9 Clock Buffer Features One-Input to Nine-Output Buffer/Driver Buffers all frequencies from DC to 133.33MHz Low power consumption for mobile applications Less than 32mA at 66.6MHz with unloaded
More informationSingle stage LNA for GPS Using the MCH4009 Application Note
Single stage LNA for GPS Using the MCH49 Application Note http://onsemi.com Overview This application note explains about ON Semiconductor s MCH49 which is used as a Low Noise Amplifier (LNA) for GPS (Global
More informationFJP13007 High Voltage Fast-Switching NPN Power Transistor
FJP3007 High Voltage Fast-Switching NPN Power Transistor Features High Voltage High Speed Power Switch Application High Voltage Capability High Switching Speed Suitable for Electronic Ballast and Switching
More informationAND8388/D. Input Dynamic Range Extension of the BelaSigna 300 Series
Input Dynamic Range Extension of the BelaSigna 300 Series INTRODUCTION This application note describes the functioning of the BelaSigna 300 input dynamic range extension (IDRX) feature. The goal of this
More informationAND8289. LED Driving with NCP/V3063
LE riving with NCP/V3063 Prepared by: Petr Konvicny, Bernie Weir ON Semiconductor Introduction Improvements in high brightness LEs present the potential for creative new lighting solutions that offer an
More informationNSVEMD4DXV6T5G. Dual Bias Resistor Transistors. NPN and PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network
Dual Bias Resistor Transistors NPN and PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network The BRT (Bias Resistor Transistor) contains a single transistor with a monolithic bias
More informationNTA4001N, NVA4001N. Small Signal MOSFET. 20 V, 238 ma, Single, N Channel, Gate ESD Protection, SC 75
Small Signal MOSFET V, 8 ma, Single, N Channel, Gate ESD Protection, SC 75 Features Low Gate Charge for Fast Switching Small.6 x.6 mm Footprint ESD Protected Gate AEC Q Qualified and PPAP Capable NVA4N
More informationMMBTA06W, SMMBTA06W, Driver Transistor. NPN Silicon. Moisture Sensitivity Level: 1 ESD Rating: Human Body Model 4 kv ESD Rating: Machine Model 400 V
Driver Transistor NPN Silicon Moisture Sensitivity Level: 1 ESD Rating: Human Body Model 4 kv ESD Rating: Machine Model 400 V Features S Prefix for Automotive and Other Applications Requiring Unique Site
More informationNTGS3441BT1G. Power MOSFET. -20 V, -3.5 A, Single P-Channel, TSOP-6. Low R DS(on) in TSOP-6 Package 2.5 V Gate Rating This is a Pb-Free Device
Power MOSFET - V, -. A, Single P-Channel, TSOP- Features Low R DS(on) in TSOP- Package. V Gate Rating This is a Pb-Free Device Applications Battery Switch and Load Management Applications in Portable Equipment
More informationPZTA92T1. High Voltage Transistor. PNP Silicon SOT 223 PACKAGE PNP SILICON HIGH VOLTAGE TRANSISTOR SURFACE MOUNT
High Voltage Transistor PNP Silicon Features These Devices are Pb Free, Halogen Free/BFR Free and are RoHS Compliant MAXIMUM RATINGS (T C = 25 C unless otherwise noted) Rating Symbol Value Unit Collector-Emitter
More informationNTS4172NT1G. Power MOSFET. 30 V, 1.7 A, Single N Channel, SC 70. Low On Resistance Low Gate Threshold Voltage Halide Free This is a Pb Free Device
Power MOSFET V,.7 A, Single N Channel, SC 7 Features Low On Resistance Low Gate Threshold Voltage Halide Free This is a Pb Free Device V (BR)DSS R DS(on) MAX I D MAX Applications Low Side Load Switch DC
More informationIs Now Part of To learn more about ON Semiconductor, please visit our website at
Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC
More informationMMSZ5221BT1 Series. Zener Voltage Regulators. 500 mw SOD 123 Surface Mount
MMSZ5BT Series Preferred Device Zener Voltage Regulators 5 mw SOD 3 Surface Mount Three complete series of Zener diodes are offered in the convenient, surface mount plastic SOD 3 package. These devices
More informationMUN5311DW1T1G Series.
MUNDWTG Series Preferred Devices Dual Bias Resistor Transistors NPN and PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network The Bias Resistor Transistor (BRT) contains a single
More informationAND9043/D. An Off-Line, Power Factor Corrected, Buck-Boost Converter for Low Power LED Applications APPLICATION NOTE.
An Off-Line, Power Factor Corrected, Buck-Boost Converter for Low Power LED Applications Prepared by: Frank Cathell ON Semiconductor Introduction This application note introduces a universal input, off
More informationNTS4173PT1G. Power MOSFET. 30 V, 1.3 A, Single P Channel, SC 70
NTS17P Power MOSFET V, 1. A, Single P Channel, SC 7 Features V BV ds, Low R DS(on) in SC 7 Package Low Threshold Voltage Fast Switching Speed This is a Halide Free Device This is a Pb Free Device Applications
More informationNTGD4167C. Power MOSFET Complementary, 30 V, +2.9/ 2.2 A, TSOP 6 Dual
Power MOSFET Complementary, 3 V, +.9/. A, TSOP 6 Dual Features Complementary N Channel and P Channel MOSFET Small Size (3 x 3 mm) Dual TSOP 6 Package Leading Edge Trench Technology for Low On Resistance
More informationCAT4237EVAL2EVB. CAT4237 High Voltage White LED Driver Evaluation Board User's Manual EVAL BOARD USER S MANUAL
CAT4237 High Voltage White LED Driver Evaluation Board User's Manual EVAL BOARD USER S MANUAL Introduction This document describes the CAT4237EVAL2 Evaluation Board for the Catalyst Semiconductor CAT4237
More informationBD809 (NPN), BD810 (PNP) Plastic High Power Silicon Transistor 10 AMPERE POWER TRANSISTORS 80 VOLTS 90 WATTS
BD89 (NPN), BD8 (PNP) Plastic High Power Silicon Transistor These devices are designed for use in high power audio amplifiers utilizing complementary or quasi complementary circuits. Features DC Current
More informationBYV SWITCHMODE Power Rectifier. ULTRAFAST RECTIFIER 16 AMPERES, 200 VOLTS t rr = 35 ns
BYV32-0 SWITCHMODE Power Rectifier Features and Benefits Low Forward Voltage Low Power Loss/High Efficiency High Surge Capacity 175 C Operating Junction Temperature A Total (8 A Per Diode Leg) PbFree Packages
More informationNCP800. Lithium Battery Protection Circuit for One Cell Battery Packs
Lithium Battery Protection Circuit for One Cell Battery Packs The NCP800 resides in a lithium battery pack where the battery cell continuously powers it. In order to maintain cell operation within specified
More informationNUP4302MR6T1G. Schottky Diode Array for Four Data Line ESD Protection
Schottky Diode Array for Four Data Line ESD Protection The NUP432MR6 is designed to protect high speed data line interface from ESD, EFT and lighting. Features Very Low Forward Voltage Drop Fast Switching
More informationPCS2I2309NZ. 3.3 V 1:9 Clock Buffer
. V 1:9 Clock Buffer Functional Description PCS2I209NZ is a low cost high speed buffer designed to accept one clock input and distribute up to nine clocks in mobile PC systems and desktop PC systems. The
More informationUMC2NT1, UMC3NT1, UMC5NT1
UMCNT, UMC3NT, UMC5NT Preferred Devices Dual Common BaseCollector Bias Resistor Transistors NPN and PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network The Bias Resistor Transistor
More informationMJD44H11 (NPN) MJD45H11 (PNP)
MJDH (NPN) MJD5H (PNP) Preferred Device Complementary Power Transistors For Surface Mount Applications Designed for general purpose power and switching such as output or driver stages in applications such
More informationNSTB1005DXV5T1, NSTB1005DXV5T5. Dual Common Base Collector Bias Resistor Transistors
NSTB005DXV5T, NSTB005DXV5T5 Preferred Devices Dual Common Base Collector Bias Resistor Transistors NPN and PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network The BRT (Bias Resistor
More informationDUAL TIMING CIRCUIT SEMICONDUCTOR TECHNICAL DATA PIN CONNECTIONS ORDERING INFORMATION. Figure Second Solid State Time Delay Relay Circuit
The MC3456 dual timing circuit is a highly stable controller capable of producing accurate time delays, or oscillation. Additional terminals are provided for triggering or resetting if desired. In the
More informationASM3P2669/D. Peak EMI Reducing Solution. Features. Product Description. Application. Block Diagram
Peak EMI Reducing Solution Features Generates a X low EMI spread spectrum clock of the input frequency. Integrated loop filter components. Operates with a 3.3V / 2.5V supply. Operating current less than
More informationMMSD301T1G SMMSD301T1G, MMSD701T1G SMMSD701T1G, SOD-123 Schottky Barrier Diodes
MMSD3TG, SMMSD3TG, MMSD7TG, SMMSD7TG, SOD-3 Schottky Barrier Diodes The MMSD3T, and MMSD7T devices are spinoffs of our popular MMBD3LT, and MMBD7LT SOT3 devices. They are designed for highefficiency UHF
More informationDistributed by: www.jameco.com 1-800-831-44 The content and copyrights of the attached material are the property of its owner. Transient Voltage Suppressors Micro Packaged Diodes for ESD Protection The
More informationCharacteristic Symbol Max Unit P D 625 mw
Advance Information Integrated Relay/Solenoid Driver Optimized to Switch 3 V to 5 V Relays from a 5 V Rail Compatible with TX and TQ Series Telecom Relays Rated up to 625 mw at 3 V to 5 V Features Low
More informationMBR735, MBR745. SWITCHMODE Power Rectifiers. SCHOTTKY BARRIER RECTIFIERS 7.5 AMPERES 35 and 45 VOLTS
MBR735, MBR75 SWITCHMODE Power Rectifiers Features and Benefits Low Forward Voltage Low Power Loss/High Efficiency High Surge Capacity 75 C Operating Junction Temperature PbFree Packages are Available*
More informationTP2 SWP 4.7 H. Designator LXP VOUTP NCP ENABLE J2 TP5 SWN FBN SWN D1 L2. R4 18k TP8 FBN. Figure 1. NCP5810DGEVB Schematic
NCP580D: Dual W Output AMOLED Driver Supply Evaluation Board Prepared by: Hubert Grandry Overview The NCP580D is a dual output DC/DC converter which can generate both a positive and a negative voltage.
More informationCAT4238AEVB. CAT LED Boost Converter Evaluation Board User's Manual EVAL BOARD USER S MANUAL.
CAT4238 0-LED Boost Converter Evaluation Board User's Manual EVAL BOARD USER S MANUAL Introduction This document describes the CAT4238AGEVB Evaluation Board for the ON Semiconductor CAT4238 High Efficiency
More informationNTR4502P, NVTR4502P. Power MOSFET. 30 V, 1.95 A, Single, P Channel, SOT 23
NTRP, NVTRP Power MOSFET V,.9 A, Single, P Channel, SOT Features Leading Planar Technology for Low Gate Charge / Fast Switching Low R DS(ON) for Low Conduction Losses SOT Surface Mount for Small Footprint
More informationNSQA6V8AW5T2 Series Transient Voltage Suppressor
Transient Voltage Suppressor ESD Protection Diode with Low Clamping Voltage This integrated transient voltage suppressor device (TVS) is designed for applications requiring transient overvoltage protection.
More informationNTJS4405N, NVJS4405N. Small Signal MOSFET. 25 V, 1.2 A, Single, N Channel, SC 88
NTJSN, NVJSN Small Signal MOSFET V,. A, Single, N Channel, SC 88 Features Advance Planar Technology for Fast Switching, Low R DS(on) Higher Efficiency Extending Battery Life AEC Q Qualified and PPAP Capable
More informationNSBC114EDP6T5G Series. Dual Digital Transistors (BRT) NPN Silicon Surface Mount Transistors with Monolithic Bias Resistor Network
Preferred Devices Dual Digital Transistors (BRT) NPN Silicon Surface Mount Transistors with Monolithic Bias Resistor Network This new series of digital transistors is designed to replace a single device
More informationPIN CONNECTIONS MAXIMUM RATINGS (T J = 25 C unless otherwise noted) SC 75 (3 Leads) Parameter Symbol Value Unit Drain to Source Voltage V DSS 30 V
NTA7N, NVTA7N Small Signal MOSFET V, 4 ma, Single, N Channel, Gate ESD Protection, SC 7 Features Low Gate Charge for Fast Switching Small.6 x.6 mm Footprint ESD Protected Gate NV Prefix for Automotive
More informationMJH6284 (NPN), MJH6287 (PNP) Darlington Complementary Silicon Power Transistors
MJH6284 (NPN), MJH6287 (PNP) Darlington Complementary Silicon Power Transistors These devices are designed for generalpurpose amplifier and lowspeed switching motor control applications. Features Similar
More informationNCL30000LED2GEVB/D Vac up to 15 Watt Dimmable LED Driver Demo Board Operation EVALUATION BOARD MANUAL
180-265 Vac up to 15 Watt Dimmable LED Driver Demo Board Operation Prepared by: Jim Young ON Semiconductor EVALUATION BOARD MANUAL Introduction The NCL30000 is a power factor corrected LED driver controller.
More information10 AMPERE DARLINGTON COMPLEMENTARY SILICON POWER TRANSISTORS VOLTS 125 WATTS MAXIMUM RATINGS THERMAL CHARACTERISTICS TIP141 TIP142
... designed for general purpose amplifier and low frequency switching applications. High DC Current Gain Min h FE = 1000 @ I C = 5 A, V CE = 4 V Collector Emitter Sustaining Voltage @ 30 ma V CEO(sus)
More informationMBR20200CT. Switch mode Power Rectifier. Dual Schottky Rectifier SCHOTTKY BARRIER RECTIFIER 20 AMPERES, 200 VOLTS
MBRCT Switch mode Power Rectifier Dual Schottky Rectifier Features and Benefits Low Forward Voltage Low Power Loss/High Efficiency High Surge Capacity 75 C Operating Junction Temperature A Total ( A Per
More informationMJE700, MJE702, MJE703 (PNP) - MJE800, MJE802, MJE803 (NPN) Plastic Darlington Complementary Silicon Power Transistors
MJE700, MJE702, MJE703 (PNP) - MJE800, MJE802, MJE803 (NPN) Plastic Darlington Complementary Silicon Power Transistors These devices are designed for generalpurpose amplifier and lowspeed switching applications.
More informationMJH11017, MJH11019, MJH11021 (PNP) MJH11018, MJH11020, MJH11022 (NPN) Complementary Darlington Silicon Power Transistors
MJH1117, MJH1119, MJH1121 () MJH1118, MJH112, MJH1122 () Complementary Darlington Silicon Power Transistors These devices are designed for use as general purpose amplifiers, low frequency switching and
More informationAdc. W W/ C T J, T stg 65 to C
Preferred Device Darlington Complementary Silicon Power Transistors This package is designed for generalpurpose amplifier and low frequency switching applications. Features High DC Current Gain h FE =
More informationAND9006/D. Using Transmission Line Pulse Measurements to Understand Protection Product Characteristics APPLICATION NOTE
Using Transmission Line Pulse Measurements to Understand Protection Product Characteristics Prepared by: Robert Ashton ON Semiconductor APPLICATION NOTE INTRODUCTION Transmission Line Pulse (TLP) is a
More informationP2042A LCD Panel EMI Reduction IC
LCD Panel EMI Reduction IC Features FCC approved method of EMI attenuation Provides up to 15dB of EMI suppression Generates a low EMI spread spectrum clock of the input frequency Input frequency range:
More informationAND9518/D DAB L-band Amplifier using the NSVF4020SG4
DAB L-band Amplifier using the NSVF4020SG4 Overview This application note explains about ON Semiconductor s NSVF4020SG4 which is used as a Low Noise Amplifier (LNA) for DAB (Digital Audio Broadcast). The
More informationBAT54CLT3G SBAT54CLT1G. Dual Common Cathode Schottky Barrier Diodes 30 VOLT DUAL COMMON CATHODE SCHOTTKY BARRIER DIODES
BAT54CLTG, SBAT54CLTG Dual Common Cathode Schottky Barrier Diodes These Schottky barrier diodes are designed for high speed switching applications, circuit protection, and voltage clamping. Extremely low
More informationLOW POWER SCHOTTKY. GUARANTEED OPERATING RANGES ORDERING INFORMATION
The SN74LS298 is a Quad 2-Port Register. It is the logical equivalent of a quad 2-input multiplexer followed by a quad 4-bit edge-triggered register. A Common Select input selects between two 4-bit input
More informationNLAS7222B, NLAS7222C. High-Speed USB 2.0 (480 Mbps) DPDT Switches
High-Speed USB 2.0 (480 Mbps) DPDT Switches ON Semiconductor s NLAS7222B and NLAS7222C are part of a series of analog switch circuits that are produced using the company s advanced sub micron CMOS technology,
More informationNVLJD4007NZTBG. Small Signal MOSFET. 30 V, 245 ma, Dual, N Channel, Gate ESD Protection, 2x2 WDFN Package
NVLJD7NZ Small Signal MOSFET V, 2 ma, Dual, N Channel, Gate ESD Protection, 2x2 WDFN Package Features Optimized Layout for Excellent High Speed Signal Integrity Low Gate Charge for Fast Switching Small
More informationPCS3P8103A General Purpose Peak EMI Reduction IC
General Purpose Peak EMI Reduction IC Features Generates a 4x low EMI spread spectrum clock Input Frequency: 16.667MHz Output Frequency: 66.66MHz Tri-level frequency Deviation Selection: Down Spread, Center
More informationPIN CONNECTIONS ORDERING INFORMATION FUNCTIONAL TABLE
The MC12026 is a high frequency, low voltage dual modulus prescaler used in phase locked loop (PLL) applications. The MC12026A can be used with CMOS synthesizers requiring positive edges to trigger internal
More informationNTK3043N. Power MOSFET. 20 V, 285 ma, N Channel with ESD Protection, SOT 723
NTKN Power MOSFET V, 8 ma, N Channel with ESD Protection, SOT 7 Features Enables High Density PCB Manufacturing % Smaller Footprint than SC 89 and 8% Thinner than SC 89 Low Voltage Drive Makes this Device
More informationMBD110DWT1G MBD330DWT1G. Dual Schottky Barrier Diodes
, Dual Schottky Barrier Diodes Application circuit designs are moving toward the consolidation of device count and into smaller packages. The new SOT363 package is a solution which simplifies circuit design,
More informationMURS120T3G Series, SURS8120T3G Series. Surface Mount Ultrafast Power Rectifiers
MURS12T3G Series, SURS812T3G Series Surface Mount Ultrafast Power Rectifiers MURS5T3G, MURS1T3G, MURS115T3G, MURS12T3G, MURS14T3G, MURS16T3G, SURS85T3G, SURS81T3G, SURS8115T3G, SURS812T3G, SURS814T3G,
More informationNGB18N40CLB, NGB18N40ACLB. Ignition IGBT 18 Amps, 400 Volts. N Channel D 2 PAK. 18 AMPS, 400 VOLTS V CE(on) 2.0 I C = 10 A, V GE 4.
NGB8N4CLB, NGB8N4ACLB Ignition IGBT 8 Amps, 4 Volts N Channel D PAK This Logic Level Insulated Gate Bipolar Transistor (IGBT) features monolithic circuitry integrating ESD and Over Voltage clamped protection
More informationNTNS3164NZT5G. Small Signal MOSFET. 20 V, 361 ma, Single N Channel, SOT 883 (XDFN3) 1.0 x 0.6 x 0.4 mm Package
NTNS36NZ Small Signal MOSFET V, 36 ma, Single N Channel, SOT 883 (XDFN3). x.6 x. mm Package Features Single N Channel MOSFET Ultra Low Profile SOT 883 (XDFN3). x.6 x. mm for Extremely Thin Environments
More informationNDF10N62Z. N-Channel Power MOSFET
NDFNZ N-Channel Power MOSFET V,.7 Features Low ON Resistance Low Gate Charge ESD Diode Protected Gate % Avalanche Tested These Devices are Pb Free, Halogen Free/BFR Free and are RoHS Compliant V DSS R
More informationAND8291/D. >85% Efficient 12 to 5 VDC Buck Converter
>5% Efficient to 5 VDC Buck Converter Prepared by: DENNIS SOLLEY ON Semiconductor General Description This application note describes how the NCP363 can be configured as a buck controller to drive an external
More informationNTJD1155LT1G. Power MOSFET. 8 V, 1.3 A, High Side Load Switch with Level Shift, P Channel SC 88
NTJDL Power MOSFET V,.3 A, High Side Load Switch with Level Shift, P Channel SC The NTJDL integrates a P and N Channel MOSFET in a single package. This device is particularly suited for portable electronic
More informationNTK3139P. Power MOSFET. 20 V, 780 ma, Single P Channel with ESD Protection, SOT 723
NTK9P Power MOSFET V, 78 ma, Single P Channel with ESD Protection, SOT 7 Features P channel Switch with Low R DS(on) % Smaller Footprint and 8% Thinner than SC 89 Low Threshold Levels Allowing.5 V R DS(on)
More informationMURA105T3G MURA110T3G SURA8110T3G. Surface Mount Ultrafast Power Rectifiers ULTRAFAST RECTIFIERS 1 AMPERE, VOLTS
MURA5T3G, MURAT3G, SURA8T3G Preferred Devices Surface Mount Ultrafast Power Rectifiers Ideally suited for high voltage, high frequency rectification, or as free wheeling and protection diodes in surface
More informationMBRA320T3G Surface Mount Schottky Power Rectifier
Surface Mount Schottky Power Rectifier Power Surface Mount Package Employing the Schottky Barrier principle in a large area metal-to-silicon power diode. State of the art geometry features epitaxial construction
More informationMMBFU310LT1G. JFET Transistor. N Channel. These Devices are Pb Free, Halogen Free/BFR Free and are RoHS Compliant. Features.
MMBFULT1G JFET Transistor N Channel Features These Devices are Pb Free, Halogen Free/BFR Free and are RoHS Compliant 2 SOURCE MAXIMUM RATINGS Rating Symbol Value Unit Drain Source Voltage V DS 25 Vdc Gate
More informationMURS320T3G, SURS8320T3G, MURS340T3G, SURS8340T3G, MURS360T3G, SURS8360T3G. Surface Mount Ultrafast Power Rectifiers
MURS32T3G, SURS832T3G, MURS34T3G, SURS834T3G, MURS36T3G, Surface Mount Ultrafast Power Rectifiers This series employs the state of the art epitaxial construction with oxide passivation and metal overlay
More informationNGD18N40CLBT4G. Ignition IGBT 18 Amps, 400 Volts N Channel DPAK. 18 AMPS 400 VOLTS V CE(on) 2.0 I C = 10 A, V GE 4.5 V
NGD8NCLB Ignition IGBT 8 Amps, Volts N Channel DPAK This Logic Level Insulated Gate Bipolar Transistor (IGBT) features monolithic circuitry integrating ESD and Over Voltage clamped protection for use in
More informationNTTFS5116PLTWG. Power MOSFET 60 V, 20 A, 52 m. Low R DS(on) Fast Switching These Devices are Pb Free and are RoHS Compliant
Power MOSFET 6 V, 2 A, 52 m Features Low R DS(on) Fast Switching These Devices are Pb Free and are RoHS Compliant Applications Load Switches DC Motor Control DC DC Conversion MAXIMUM RATINGS ( unless otherwise
More information2N6387, 2N6388. Plastic Medium-Power Silicon Transistors DARLINGTON NPN SILICON POWER TRANSISTORS 8 AND 10 AMPERES 65 WATTS, VOLTS
Plastic Medium-Power Silicon Transistors These devices are designed for generalpurpose amplifier and lowspeed switching applications. Features High DC Current Gain h FE = 2500 (Typ) @ I C = 4.0 Adc CollectorEmitter
More informationMURA160T3G SURA8160T3G. Surface Mount Ultrafast Power Rectifier ULTRAFAST RECTIFIER 1 AMPERE, 600 VOLTS
MURA6T3G, SURA86T3G Surface Mount Ultrafast Power Rectifier Ideally suited for high voltage, high frequency rectification, or as free wheeling and protection diodes in surface mount applications where
More informationNTMS5835NL. Power MOSFET 40 V, 12 A, 10 m
Power MOSFET V, 2 A, m Features Low R DS(on) Low Capacitance Optimized Gate Charge These Devices are Pb Free, Halogen Free/BFR Free and are RoHS Compliant MAXIMUM RATINGS ( unless otherwise stated) Parameter
More information1 A Constant-Current LED Driver with PWM Dimming
1 A Constant-Current Driver with PWM Dimming FEATURES Accurate 1 A current sink Up to 25 V operation on pin Low dropout 500 mv at 1 A current set by external resistor High resolution PWM dimming via EN/PWM
More informationMARKING DIAGRAM Mechanical Characteristics. B2E1 Epoxy Meets UL 94 V in
Surface Mount Schottky Power Rectifier Power Surface Mount Package This device employs the Schottky Barrier principle in a metal to silicon power rectifier. Features epitaxial construction with oxide passivation
More informationMJD44H11 (NPN) MJD45H11 (PNP) Complementary Power Transistors. DPAK For Surface Mount Applications
MJDH (NPN) MJD5H (PNP) Complementary Power Transistors For Surface Mount Applications Designed for general purpose power and switching such as output or driver stages in applications such as switching
More informationP2I2305NZ. 3.3V 1:5 Clock Buffer
3.3V :5 Clock Buffer Functional Description P2I2305NZ is a low cost high speed buffer designed to accept one clock input and distribute up to five clocks in mobile PC systems and desktop PC systems. The
More informationMJW0281A (NPN) MJW0302A (PNP) Complementary NPN PNP Power Bipolar Transistors 15 AMPERES COMPLEMENTARY SILICON POWER TRANSISTORS 260 VOLTS 150 WATTS
MJW28A (NPN) MJW32A (PNP) Preferred Devices Complementary NPN PNP Power Bipolar Transistors These complementary devices are lower power versions of the popular MJW328A and MJW32A audio output transistors.
More informationMUN5216DW1, NSBC143TDXV6. Dual NPN Bias Resistor Transistors R1 = 4.7 k, R2 = k. NPN Transistors with Monolithic Bias Resistor Network
MUN526DW, NSBC43TDXV6 Dual NPN Bias Resistor Transistors R = 4.7 k, R2 = k NPN Transistors with Monolithic Bias Resistor Network This series of digital transistors is designed to replace a single device
More informationEMC2DXV5T1G, EMC3DXV5T1G, EMC4DXV5T1G, EMC5DXV5T1G. Dual Common Base-Collector Bias Resistor Transistors
EMCDXV5TG, EMCDXV5TG, EMCDXV5TG, EMC5DXV5TG Dual Common Base-Collector Bias Resistor Transistors NPN and PNP Silicon Surface Mount Transistors with Monolithic Bias Resistor Network The BRT (Bias Resistor
More informationNTMS5838NL. Power MOSFET 40 V, 7.5 A, 20 m
Power MOSFET V, 7.5 A, 2 m Features Low R DS(on) Low Capacitance Optimized Gate Charge These Devices are Pb Free, Halogen Free/BFR Free and are RoHS Compliant MAXIMUM RATINGS ( unless otherwise stated)
More informationSN74LS122, SN74LS123. Retriggerable Monostable Multivibrators LOW POWER SCHOTTKY
Retriggerable Monostable Multivibrators These dc triggered multivibrators feature pulse width control by three methods. The basic pulse width is programmed by selection of external resistance and capacitance
More information2N5194G, 2N5195G. Silicon PNP Power Transistors 4 AMPERE POWER TRANSISTORS PNP SILICON VOLTS
, Silicon PNP Power Transistors These devices are designed for use in power amplifier and switching circuits; excellent safe area limits. Features Complement to NPN 2N5191, 2N5192 These Devices are PbFree
More informationMBRB20200CT. SWITCHMODE Power Rectifier. Dual Schottky Rectifier SCHOTTKY BARRIER RECTIFIER 20 AMPERES, 200 V
MBRBCT SWITCHMODE Power Rectifier Dual Schottky Rectifier This device uses the Schottky Barrier technology with a platinum barrier metal. This state of the art device is designed for use in high frequency
More informationNTHD4502NT1G. Power MOSFET. 30 V, 3.9 A, Dual N Channel ChipFET
NTHDN Power MOSFET V,.9 A, Dual N Channel ChipFET Features Planar Technology Device Offers Low R DS(on) and Fast Switching Speed Leadless ChipFET Package has % Smaller Footprint than TSOP. Ideal Device
More informationTIP47G, TIP48G, TIP50G. High Voltage NPN Silicon Power Transistors 1.0 AMPERE POWER TRANSISTORS NPN SILICON VOLTS 40 WATTS
High Voltage NPN Silicon Power Transistors This series is designed for line operated audio output amplifier, SWITCHMODE power supply drivers and other switching applications. Features 25 V to V (Min) V
More informationDual N-Channel, Digital FET
FDG6301N-F085 Dual N-Channel, Digital FET Features 25 V, 0.22 A continuous, 0.65 A peak. R DS(ON) = 4 @ V GS = 4.5 V, R DS(ON) = 5 @ V GS = 2.7 V. Very low level gate drive requirements allowing directoperation
More informationMMUN2211LT1 Series. NPN Silicon Surface Mount Transistor with Monolithic Bias Resistor Network
MMUNLT Series Preferred Devices Bias Resistor Transistor NPN Silicon Surface Mount Transistor with Monolithic Bias Resistor Network This new series of digital transistors is designed to replace a single
More information