FIBRE CHANNEL CONNECTORS

Transcription

1 HIGH SPEED INTERCONNECTS FIBRE CHANNEL/ETHERNET/FIREWIRE FIBRE CHANNEL CONNECTORS 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

2 HIGH SPEED INTERCONNECT SOLUTIONS INTRODUCTION Sabritec offers a complete line of differential Twinax and Quadrax connectors, contacts, and cable assemblies for high speed Ethernet, Firewire, and applications. Differential pair twinaxial connectors and cable assemblies offer the utmost in high speed matched impedance data-on-demand applications. The differential pair and signal to shield characteristic impedance is maintained throughout the connector pair. A true twinaxial connector interface ensures signal integrity, minimizing jitter and data rate errors. Sabritec manufactures connectors for the following protocols: Ethernet: 0 Base-T, 00 Base-T, 000 Base-T Firewire: IEEE 394a and 394b USB, DVI, and Infiniband Quadsplitter Sabritec features a newly developed concept called a quadsplitter. Quadrax is a system where four conductors are located within a single conducting enclosure. The connection to two separate twinax cables is accomplished without disturbing the differential or signal-to-shield impedances values. A complete series of connectors are available utilizing the Quadsplitter technology with MIL-DTL Series III connector types available in shell size and shell size 5 housings. Backplane Connectors In standard VME cards for low data rate signaling, connectors are widely available to carry non-shielded signaling for the VME bus from the interface via motherboard to daughter card assembly designated as I/O plug-in modules. The industry standard defines these connectors typically as P and P3 connectors. Sabritec has taken the standard housing configuration of the P & P3 mounting dimensions while incorporating true differential pair contacts within the P & P3 dimensional constraints. Data sampling rates exceeding Gbits/second can be driven via matched impedance differential pair interconnections for boardto-board high speed data transfer as well as blind mate I/O plug in modular applications. Sabritec's P connector housing contains position true differential pair blind mate contacts allowing board designers to carry high density differential pair signals from the LRU via motherboard to daughter-card plug in module with a single connector P type housing. This allows for the use of standard VME bus architecture cages for high speed fibre channel connection. QUADSPLITTER CONNECTORS PG. 60 MIL-DTL CONNECTORS PG. 6 MIL-C-8659 ARINC 404 PG. 70 ARINC 600 PG. 77 MIL-DTL-8357 PG. 83 HIGH SPEED RUGGED D- SUB PG. 86 BACKPLANE/PANEL MOUNT CONNECTORS PG. 9 PCB & CABLE MOUNT CONNECTORS PG. 99 MICRO TWINAX/QUADRAX PG. 0 Connector Series For single stand-alone interconnect applications for a differential pair signal to the PCB, Sabritec offers a complete series of true differential pair connectors for board-board jumper applications. These are available in quick disconnect and threaded versions including straight and right angle cable mount and PCB mount connectors. The cable mount connectors are designed for 00 and 50 Ohm differential pair impedance cable types which maintain the differential pair impedance and signal to shield impedance throughout the mated connector pair. MODULAR BLOCK PG. 07 CABLE ORDERING PG. 08 Differential Twinax Contacts Differential twinax contacts are designed for use in MIL-DTL-38999, MIL-DTL-8357, ARINC 404, ARINC 600 and D-Sub connectors series. Twinax contacts consist of two inner contacts to form 00 or 50 ohm differential impedance. Micro Twinax The Micro Twinax line features matched impedance miniaturized connectors that provide the user with controlled impedance and tightly spaced PCB footprint spacing. These connectors are available in true differential twinax packages with NDL, SMA, and Micro D size constraints Gillette Avenue, Irvine, California Telephone (949) Fax (949)

3 HIGH SPEED INTERCONNECTS TECHNICAL SPECIFICATIONS ARINC 404 and Arinc 600 Connectors The ARINC 600 and 404 series connectors can be routed with either high speed differential pair matched impedance contacts (50 Ohm and 00 Ohm) or with Ethernet based quad contacts 00 Ohm impedance assemblies. The ARINC 600 series can also include ruggedized expanded beam or butt-joint fiber optic contacts. MIL-DTL-8357 The MIL-DTL-8357 series connectors come standard with anti-rotational keyed insert assemblies for High-Speed Fibre Channel or Ethernet Twinax and Quadrax Contacts. Designed for extreme environmental concerns with very high levels of shock, vibration, and humidity. Quadrax Contacts Designed to meet ARINC 600 Quad based Ethernet specifications, Sabritec's Quadrax contacts consist of four center contacts (Quad configuration applications exceeding Gbit/sec) forming two 00 or 50 ohm matched impedance differential pairs. These contacts have a low impedance grounding shield and are ideal for Ethernet 00 Base-T (00 Ohm), (50 ohm) and IEEE 394b Firewire (0 ohm) applications. Modular Block (MBC) Connectors Sabritec's MBC connectors consist of dual twinax blindmate assemblies permitting the transmit and receive signaling of high speed Ethernet data rates in one connector. This series allows for modularity in PCB routing of high speed signaling. Capable of 00 Ohm differential pair matched impedance, these connectors allow for maximum space utilization modularity and true signal integrity. ELECTRICAL SPECIFICATIONS Temperature Rating -65ºC to + 5ºC Corrosion Shock Vibration Thermal Shock Durability Dielectric Withstanding Voltage Insulation Resistance Contact Current Rating Data Rates Differential Pair Cable Impedance Signal to Shield Cable Impedance Ruggedized D-Sub Quad/Twinax Ethernet Connectors Designed to ground the outer shield of a twinax or quadrax contact directly to the shell of the connector. A multi-finger ground spring, fixed around the shell provides a multipoint contact engagement for superior EMI shielding. The result is an extremely low contact resistance when measured from the contact outer body to the connector flange. These connectors provide low RF noise and high durability of up to,000 mating cycles. Offered with 00 ohm quadrax and/or 00 and 50 ohm fibre channel twinax contacts. MIL-STD-0 Method 0, Test Condition B MIL-STD-0 Method 3, Test Condition B MIL-STD-0 Method 04, Test Condition B MIL-STD-0 Method 07, Test Condition B 500 Mate/Unmate cycles min. MECHANICAL & ENVIRONMENTAL SPECIFICATIONS MATERIALS & FINISHES Shells Insulators Contacts 50 VDC max Megaohms min 3.0 Amps D.C. max Gbits/sec min. 50-ohm + 5-ohm 00-ohm + 0-ohm 75-ohm + 0-ohm 50-ohm + 7-ohm Brass per ASTM-B6 Nickel per SAE-AMS-QQ Gold per ASTM-B488 Aluminum per ASTM-B Electroless Nickel per MIL-C-6074 Cadmium per SAE-AMS-QQ-P-46 PTFE per ASTM-D70 Ultem per ASTM-D505 Brass per ASTM-B6 Be Cu per ASTM B96 Gold per ASTM-B488 Testing Capabilities Sabritec can test eye pattern, jitter, skew, and insertion loss on differential pair 00 ohm and 50 ohm fibre channel and high speed Gigabit Ethernet applications. Our testing capabilities support wide bandwidth (DC to 50 GHz with up to.5 GHz Trigger). We utilize the Tektronix CSA8000 to measure the differential pair TDR impedance between twinax connectors, cable assemblies, and quad cable fibre channel interconnect systems. Using the CSA8000 ensures the most accurate acquired signal for high speed communications testing. CSA8000 testing features 0 GHz Bandwidth with 80E04 sampling module, 35 ps TDR Reflected Rise Time, Differential TDR, and Crosstalk. Sabritec does not offer standard QPL slash sheet part #'s for multipin circular and rack & panel connectors. Our connectors are fully intermateable with all slash sheet part #'s Gillette Avenue, Irvine, California Telephone (949) Fax (949)

4 QUADSPLITTER TECHNOLOGY HIGH SPEED QUAD TO TWINAX CONVERSION Currently high-speed data transference requires transmission systems that minimize reflections. This is achieved through controlled characteristic impedance from source to load. In microwave systems, this is accomplished with waveguide or coaxial transmission lines. In both cases, the line geometry is the determining factor along with dielectric and conductor materials. Steps, bends, protrusions etc. will invariably cause reflections with consequent loss of transmission efficiency. In -wire differential- mode transmissions this is acceptable at lower data rates, however, when data rates become higher, such as fibre channel (into microwave frequencies), the line characteristic impedances become much more critical. In fibre channel systems the source and load differential impedances are usually high (00-50 ohm). Achieving these high impedances in coaxial transmission lines and connectors is size prohibitive. As a result, a line configuration such as twinax where the signals carried between a pair of conductors (usually round) critically spaced from each other and surrounded by a conductive enclosure is used. In this differential line high impedances are easily obtained since the mutual capacitance between the conductors is minimized. A more efficient development for fibre channel transmission is the Quadrax, a single enclosure with four wires where a diagonal pair of conductors forms a twinax differential pair. A problem arises when the Quadrax to Twinax conversion takes place and the channels must be physically separated. The diagonal pairs will cross over resulting in impedance disturbance and reflections with some cross talk. At low frequencies or data rates, this is somewhat manageable, however when data rates approach microwave frequencies the resulting system degradation becomes unacceptable. This problem is effectively overcome by employment of stripline or microstrip transmissions. The unique feature of this method is the placement of the traces and ground planes within a stack of circuit boards where the lines from the quadrax input contact pins couple strait onto the stripline traces without crossing over or disturbing the relative positions of the selected diagonal pairs. This means the impedance is relatively consistent and therefore not frequency sensitive. Referring to the assembly and circuit boards below, it can be seen that by locating a common ground plane between two trace layers, the signal pairs will be isolated and in the controlled impedance of effectively separate transmission systems. In the above case, the separated pairs run to surface pads that, thru selected plated-thru holes, connect to the assigned embedded traces. Note the diagonal pairs from the Quadrax interface are attached to the pads on their assigned traces, while merely passing through the board with traces and pads belonging to the other diagonal pair. The paired traces are routed to the board edge case, and will be soldered to the separated twinax cables. The chart below is a differential TDR showing the impedance in the transition region. TDR Traces * Patent pending Circuit Boards Gillette Avenue, Irvine, California Telephone (949) Fax (949)

5 QUADSPLITTER CONNECTORS MIL-DTL SERIES III QUAD INSERT TO TWINAX CONVERSION ASSEMBLIES Size Quad Receptacle to Socket Insert Right Angle Twinax Cables to Open Lead Y Polarization N A 3 B 4 C 5 D 6 E Y = Connector Polarization 0990Y-000 Differential Twinax Please specify cable length when ordering or use the RFQ worksheet in the back of this catalog. Size 5 Four Way Quad Pin Insert Receptacle to 8 Right Angle Twinax Cables to Open Lead Y Polarization N A 3 B 4 C 5 D 6 E Y = Connector Polarization 0370Y-3000 Differential Twinax Please specify cable length when ordering or use the RFQ worksheet in the back of this catalog. See Page 08 for Cable Assembly Ordering Information 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

6 QUAD INSERTS -4 SINGLE QUAD MIL-DTL SERIES III QUAD INSERT PLUG CONNECTORS & ASSEMBLIES MIL-DTL Size Pin Insert Quad Plug to Plug Cable Assembly XXX = Cable Length in Inches Y = Connector Polarization 0990Y-XXX Differential Quad Y-3XXX Differential Quad Y Polarization N A 3 B 4 C 5 D 6 E MIL-DTL Size -4 Connector Saver Quad Configuration.00 MAX "Y" POL RECEPTACLE SOCKET PLUG PIN 4 3 3/4-.P-.3L-TS BAND-RED FULLY MATED INDICATOR.075 (TYP) 4 3 INSERT CAVITY.50 (TYP) Part Number Polarizatoin N A B C D E See Page 08 for Cable Assembly Ordering Information Gillette Avenue, Irvine, California Telephone (949) Fax (949)

7 MIL-DTL T* RECEPTACLES & 5-4 FOUR WAY QUAD MIL-DTL SERIES III CONNECTORS MIL-DTL Size 5 Four Way Socket Insert Quad Plug Y = Connector Polarization 0340Y-000 Differential Quad Y-00 Differential Quad Y Polarization N A 3 B 4 C 5 D 6 E Please specify cable length when ordering or use the RFQ worksheet in the back of this catalog. Box Mount Receptacle Pin Insert 5-8 PT* to 8 R/A Twinax Cables to Open Lead * Connector Receptacle is supplied fully loaded with twinax pin contacts terminated to differential pair twinax cable to open lead (all cavities included). Y = Connector Polarization 0370Y-00X Differential Twinax Y Polarization N A 3 B 4 C 5 D 6 E Please specify cable length when ordering or use the RFQ worksheet in the back of this catalog. See Page 08 for Cable Assembly Ordering Information 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

8 MIL-DTL HIGH SPEED SERIES MIL-DTL ORDERING INFORMATION Differential twinax contacts are designed for use in MIL-DTL-38999, MIL-DTL-8357, ARINC 404, ARINC 600 and D-Sub connectors series. Twinax contacts consist of two inner contacts to form 00 or 50 ohm differential impedance. Designed to meet ARINC 600 Quad Ethernet specifications, Sabritec's Quadrax contacts consist of four center contacts (Quad configuration applications exceeding Gbit/sec) forming two 00 or 50 ohm matched impedance differential pairs. These contacts have a low impedance grounding shield and are ideal for Ethernet 00 Base-T (00 Ohm), Fibre Channel (50 ohm) and IEEE 394B Firewire (0 ohm) applications. PART NUMBER ASSIGNMENT _ III _ B _ R C _ 75 _ P _ C _ N Polarization N, A, B, C, D, E Prefix Series I, III, IV Shell Style J Jam Nut B Box Mount W- Wall Mount Contact Termination S- Solder Cup P- PC Tail C- Crimp Contact Type P Pin S- Socket Insert Arrangment Mounting F- Front R - Rear Material/Plating C- Aluminum Alloy/Cadmium Over Nickel N- Aluminum Alloy/Electroless Nickel S- Stainless Steel/Electroless Nickel CC-Composite/Cadmium Over Nickel CN-Composite/Electroless Nickel *Consult factory for alternate plating options Shell Size Note: Twinax/Quadrax Contacts are sold seperately MIL-DTL with Single Way Quad Gillette Avenue, Irvine, California Telephone (949) Fax (949)

9 MIL-DTL TWINAX/QUADRAX MIL-DTL SERIES III CONNECTOR SHELLS/SIZE 8 TWINAX CONTACTS MIL-DTL Twinax/Quadrax Plug MIL-DTL Twinax/Quadrax Receptacle C thd 0.50/0.500 (Fully Mated).40 Max W V Shell Size C Thread. Pitch.3 Lead P ±.008 R BSC R BSC Shell Size B Dia K Max -.0 S Dia Max V Max W Max X Max PP Max ±.008 Z Max.0 S / / Size 8 Twinax Pin Contact 00 and 50 Ohm.97 (.00) Part Number Impedance Cable Type Cable Ohm Differential Twinax (30 ) Ø Ohm Differential Twinax Ohm Differential Twinax CONTACT EXTRACTION TOOL Ohm Flexible Twinax Ohm Flexible Twinax Size 8 Twinax Socket Contact 00 and 50 Ohm.68 (.500) Part Number Impedance Cable Type Cable Ohm Differential Twinax (30 ) Ohm Differential Twinax Ohm Differential Twinax CONTACT EXTRACTION TOOL Ohm Flexible Twinax Ohm Flexible Twinax See Page 08 for Cable Assembly Ordering Information 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

10 SIZE 8 TWINAX/QUADRAX CONTACTS FOR MIL-DTL SERIES III CONNECTORS Size 8 Twinax Pin 00 and 50 Ohm PCB Mount Ø.50 4X Ø.035 MIN (30 ) Ø.8 45 (TYP) C L , 50 OHM.03 CONTACT EXTRACTION TOOL (.00) Ø.67 Ø.00 X Size 8 Quadrax Pin 00 Ohm C L MOUNTING HOLE 4X Ø.05 MIN Part Number Impedance Ohm Ohm Ø Differential Quad (30 ).03 CONTACT EXTRACTION TOOL Size 8 Quadrax Socket 00 Ohm (.500) (30 ) Differential Quad CONTACT EXTRACTION TOOL Size 8 Quadrax Pin 00 and 50 Ohm PCB Mount Ø.50 4X Ø.035 MIN 45 (TYP) 4 3 Ø.8 C L 4X OHM (30 ).03 CONTACT EXTRACTION TOOL Ø.67 Ø.00 X CL 4X OHM MOUNTING HOLE 4X Ø.05 MIN Part Number Impedance Ohm Ohm See Page 08 for Cable Assembly Ordering Information Gillette Avenue, Irvine, California Telephone (949) Fax (949)

11 HIGH SPEED SIZE 0 CONTACTS FOR MIL-DTL SIZE 0 TWINAX SPECIAL CRIMP AND SOLDER CONTACTS Size 0 Twinax Pin Crimp Contact 00 Ohm.97 (.65) CRIMP AREA.070 Ø.75 Ø MAX.60 HEX Size 0 Twinax Socket Crimp Contact 00 Ohm.65 Ø MAX (.65) CRIMP AREA Differential Twinax Ø.75 Ø HEX Differential Twinax Size 0 Twinax Pin Solder Contact 00 Ohm.97.0 MAX Ø.06 SOLDER, PLCS.070 Ø.30 Ø Differential Twinax Size 0 Twinax Socket Solder Contact 00 Ohm.65 Ø MAX Ø.70 Ø.06 SOLDER, PLCS.070 Ø Differential Twinax See Page 08 for Cable Assembly Ordering Information 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

12 INSERT ARRANGEMENTS MIL-DTL TWINAX/QUADRAX INSERT ARRANGEMENTS Size #8 Twinax /Quadrax (T/Q) Cavities are Anti-Rotational T/Q T/Q T/Q T/Q T/Q T/Q T/Q T/Q T/Q T/Q T/Q T/Q Note: Size #8 Twinax/Quadrax contact cavities are common ground to the connector shell with a ground resistance of 0 milli-ohms maximum or insulated from common ground. Consult factory for details Gillette Avenue, Irvine, California Telephone (949) Fax (949)

13 Gillette Avenue, Irvine, California Telephone (949) Fax (949) Contact cavities are anti-rotational to fit Size 0 Twinax 00 Ohm differential pair impedance Contacts Sabritec Size 0XT Twinax Contact Layouts Crimp Version Ø XT Ø XT Ø.99-8 XT Ø XT Ø XT Sabritec Size 0XT Twinax Contact Layouts Solder Version 7-6 XT 5-9 XT - XT Ø.777 Ø.40 Ø XT 3- XT Ø.57 Ø.65 TWINAX SIZE 0 INSERT ARRANGEMENTS SPECIAL SIZE 0XT CONTACT LAYOUTS Suitable for Sabritec P/N: and Suitable for Sabritec P/N: and

14 ARINC 404 SERIES CONNECTORS MIL-C-8659 ANTI-ROTATIONAL TWINAX INSERT ARRANGEMENTS Sabritec s ARINC 404 connector series comes available with high speed and/or Ethernet Twinax and Quadrax contacts. These connectors come standard with anti-rotational keyed insert assemblies and high speed differential pair signaling. Designed for 394 Firewire, Gigabit Ethernet, 00 Base-T Ethernet, high speed video Hot-Link, and data links. Quadrax high speed Ethernet and matched impedance 50-Ohm differential pair insert assemblies are available. ARINC 404 INSERT ARRANGEMENTS NOTE: SIZE 5 TWINAX AND QUADRAX CONTACT CAVITIES ARE ANTI-ROTATIONAL For ARINC Size Quad Contact Only Gillette Avenue, Irvine, California Telephone (949) Fax (949)

15 ARINC 404 SERIES CONNECTORS MIL-C-8659 SHELL SIZE Part Number Assignment _ 404 _ C _ A06 _ P _ B57 _ P _ P Prefix Shell Size,, 3, 4 Contact Termination S- Solder Cup P- PC Tail C- Crimp Plating C- Cadmium (Yellow Chromate N- Electroless Nickel Insert Arrangements Cavity A, B, C, D Contact Type P Pin S- Socket ARINC 404 Shell Size Plug Arinc 404 Shell Size Receptacle 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

16 ARINC 404 SERIES CONNECTORS MIL-C-8659 SHELL SIZE ARINC 404 Shell Size Plug ARINC 404 Shell Size Receptacle Gillette Avenue, Irvine, California Telephone (949) Fax (949)

17 ARINC 404 SERIES CONNECTORS MIL-C-8659 SHELL SIZE 3 ARINC 404 Shell Size 3 Plug ARINC 404 Shell Size 3 Receptacle 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

18 ARINC 404 SERIES CONNECTORS MIL-C-8659 SHELL SIZE 4 ARINC 404 Shell Size 4 Plug ARINC 404 Shell Size 4 Receptacle Gillette Avenue, Irvine, California Telephone (949) Fax (949)

19 ARINC 404 CONTACTS SIZE 5 TWINAX AND QUADRAX CONTACTS ARINC 404 Size 5 Twinax Pin Contact 00 and 50 Ohm Part Number Impedance Cable Type Cable Ohm Differential Twinax Ø Ohm Differential Twinax Ohm Flexible Twinax INTERGRATED EXTRACTION TOOL Ohm Differential Twinax Ohm Flexible Twinax ARINC 404 Size 5 Twinax Socket Contact 00 and 50 Ohm Part Number Impedance Cable Type Cable Ohm Differential Twinax Ohm Differential Twinax Ohm Flexible Twinax INTERGRATED EXTRACTION TOOL Ohm Differential Twinax Ohm Flexible Twinax ARINC 404 Size 5 Quadrax Pin Contact 00 Ohm Ø Differential Quad INTERGRATED EXTRACTION TOOL ARINC 404 Size 5 Quadrax Socket Contact 00 Ohm Differential Quad INTERGRATED EXTRACTION TOOL See Page 08 for Cable Assembly Ordering Information 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

20 ARINC 404 CONTACTS SIZE QUADRAX CONTACTS 00 AND 50 OHM ARINC 404 Size Quadrax Pin Contact 00 and 50 Ohm Differential Quad INTERGRATED EXTRACTION TOOL CABLE STRAIN RELIEF ARINC 404 Size Quadrax Socket Contact 00 and 50 Ohm Differential Quad CABLE.03 STRAIN INTERGRATED RELIEF EXTRACTION TOOL See Page 08 for Cable Assembly Ordering Information Gillette Avenue, Irvine, California Telephone (949) Fax (949)

21 ARINC 600 ETHERNET INSERTS ETHERNET 00 OHM INSERT ARRANGEMENTS Sabritec s ARINC 600 connector series is available with High Speed Ethernet insert assemblies. Designed for interconnect systems including 00 Base-T, Ethernet, and high speed video Hot-Link. These connectors can be fitted with Ethernet based Quad 00-Ohm contacts or differential pair 00 Ohm or 50 Ohm matched impedance contacts. The ARINC 600 Series can also be routed with ruggedized expaned beam fiber optic contacts or concentric triaxial contacts designed for numerous low-loss twinaxial and concentric triax cables in a variety of impedance values. Prefix Shell Size,, 3 Part Number Assignment _ 600 _ N _ 50 P 50 _ P 3C P _ S Contact Termination S- Solder Cup P- PC Tail C- Crimp Insert Arrangements Cavity A, B, C, D, E, F Plating C- Cadmium (Yellow Chromate) N- Electroless Nickel Contact Type P Pin Front Release/Rear Removable PC Tail Version S- Socket Rear Release/Rear Removable Cable Mount Type Insert Arrangements ARINC 600 Front Release/Front Removable Insert Layouts II II II II I ARINC 600 Rear Release/Rear Removable Insert Layouts II II II II I 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

22 ARINC 600 SHELL HOUSING SHELL SIZE RACK AND PANEL SERIES ARINC 600 Shell Size Plug ARINC 600 Shell Size Receptacle Gillette Avenue, Irvine, California Telephone (949) Fax (949)

23 ARINC 600 SHELL HOUSING SHELL SIZE RACK AND PANEL SERIES ARINC 600 Shell Size Plug ARINC 600 Shell Size Receptacle 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

24 ARINC 600 SHELL HOUSING SHELL SIZE 3 RACK AND PANEL SERIES ARINC 600 Shell Size 3 Plug ARINC 600 Shell Size 3 Receptacle Gillette Avenue, Irvine, California Telephone (949) Fax (949)

25 SIZE 8 QUADRAX CONTACTS ARINC 600 SIZE 8 MATCHED IMPEDANCE 00 OHM QUADRAX CONTACTS ARINC 600 Removable Size 8 Pin Quadrax Contact 00 Ohm Rear Release/Rear Removable Differential Quad ARINC 600 Removable Size 8 Socket Quadrax Contact 00 Ohm Rear Release/Rear Removable Differential Quad ARINC 600 Removable Size 8 Pin Quadrax Contact PCB Mount 00 Ohm Front Release/Rear Removable P/N See Page 08 for Cable Assembly Ordering Information 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

26 SIZE 8 TWINAX CONTACTS ARINC 600 SIZE 8 TWINAX CONTACTS ARINC 600 Size 8 Twinax Pin Contact 00 and 50 Ohm Matched Impedance Part Number Impedance Cable Type Cable Ohm Differential Twinax Ohm Differential Twinax Ohm Differential Twinax Ohm Flexible Twinax Ohm Flexible Twinax ARINC 600 Size 8 Twinax Socket Contact 00 and 50 Ohm Matched Impedance Part Number Impedance Cable Type Cable Ohm Differential Twinax Ohm Differential Twinax Ohm Differential Twinax Ohm Flexible Twinax Ohm Flexible Twinax See Page 08 for Cable Assembly Ordering Information Gillette Avenue, Irvine, California Telephone (949) Fax (949)

27 MIL-DTL-8357 SERIES CONNECTORS MIL-DTL-8357 connectors come standard with antirotational keyed insert assemblies for High-Speed Fibre Channel or Ethernet Twinax and Quadrax contacts. MIL- DTL-8357 connectors are designed for extreme environmental concerns including shock, vibration and humidity. Filtered EMI/EMP connectors are also available. Offered in a number of different contact arrangements and shell sizes, these connectors meet all applicable requirements of MIL-DTL Prefix Shell Size A, 3A, 4A PART NUMBER ASSIGNMENT AND INSERT ARRANGEMENTS MIL-DTL-8357 PART NUMBER ASSIGNMENT 8357 _ 4A N _ 50 P 50 _ P 3C P _ S Contact Termination S- Solder Cup P- PC Tail C- Crimp Insert Arrangements Cavity A, B, C, D, E, F Plating C- Cadmium (Yellow Chromate N- Electroless Nickel Contact Type P Pin S- Socket MIL-DTL-8357 INSERT ARRANGEMENTS Insert 50 Size # Contacts Insert 00 Size # Contacts Insert 3 0 Size # Contacts 4 Size #8 T/C Insert 4 4 Size #0 Contacts 0 Size #6 Contacts Insert 5 47 Size #0 Contacts Size #8 T/C Insert 6 4 Size # Contacts Insert 7 6 Size #8 T/C Specify T = Twinaxial Cavity (Anti-Rotational) C= Coaxial/Triaxial Cavity For Inserts 3, 5, 7, Size 8 Cavity Only, as suffix to Insert Identification Part Number Insert 8 Blank Insert9 Blank Insert 0 60 Size #0 Contacts Insert 0 Size #8 T/C Insert 50 Size # Contacts 8 Size # Contacts 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

28 MIL-DTL-8357 CONNECTORS SHELL SIZE 4 PLUG AND RECEPTACLE MIL-DTL-8357 Shell Size 4A Plug MIL-DTL-8357 Shell Size 4A Receptacle Gillette Avenue, Irvine, California Telephone (949) Fax (949)

29 MIL-DTL-8357 CONTACTS SIZE 8 TWINAX/QUADRAX CONTACTS MIL-DTL-8357 Size 8 Twinax Pin Contact 00 and 50 Ohm.50 (.350) Part Number Impedance Cable Type Cable Ohm Differential Twinax (30 ) Ø Ohm Differential Twinax Ohm Flexible Twinax CONTACT EXTRACTION TOOL Ohm Differential Twinax Ohm Flexible Twinax MIL-DTL-8357 Size 8 Twinax Socket Contact 00 and 50 Ohm.595 (.500) Part Number Impedance Cable Type Cable Ohm Differential Twinax (30 ) Ohm Differential Twinax Ohm Flexible Twinax CONTACT EXTRACTION TOOL Ohm Differential Twinax Ohm Flexible Twinax MIL-DTL-8357 Size 8 Quadrax Pin Contact 00 Ohm (.350) Ø Differential Quad (30 ).03 CONTACT EXTRACTION TOOL MIL-DTL-8357 Size 8 Quadrax Socket Contact 00 Ohm (30 ).595 (.500) Differential Quad CONTACT EXTRACTION TOOL See Page 08 for Cable Assembly Ordering Information 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

30 HIGH SPEED RUGGED D-SUBMINIATURE CONNECTORS Shell Size Arrangement - # 9 Quad/Twinax Contacts QUAD/TWINAX PANEL MOUNT D-SUBMINIATURE CONNECTORS High impedance D-Sub connectors are designed to ground the outer shield of a twinax or quadrax contact directly to the shell of the connector. A multi-finger ground spring, fixed around the shell provides a multi-point contact engagement for superior EMI shielding. The result is an extremely low contact resistance when measured from the contact outer body to the connector flange. These connectors provide low RF noise and high durability of up to,000 mating cycles. Meets or exceeds all requirements of MIL-STD-0 of shock and vibration. Offered with 00 ohm quadrax and/or 00/50 ohm differential pair twinax contacts. Quadrax contacts consist of four center contacts with a low impedance grounding shield. Twinax contacts offer true differential pair signaling with 00/50 Ohm impedance between conductors. Rugged D-Sub Quad / Twinax connectors are ideal for Rib Ethernet, Firewire and all fibre channel system requirements. Shell Size Arrangement -4 4 # 9 Quad/Twinax Contacts Shell Size 3 Arrangement # 9 Quad/Twinax Contacts R.050 Ø.090 R.050 Ø.5 R.06 Ø.5 Shell Size 4 Arrangement # 9 Quad/Twinax Contacts Shell Size 5 Arrangement 5- # 9 Quad/Twinax Contacts R.06 Ø.50 R.06 Ø.50 Please consult factory for environmentally sealed and backshell connectors Gillette Avenue, Irvine, California Telephone (949) Fax (949)

31 HIGH SPEED RUGGED D-SUBMINIATURE CONNECTORS QUAD/TWINAX PANEL MOUNT D-SUBMINIATURE CONNECTORS Quad/Twinax D-Sub Plug "H" "G".400 Contacts are sold separately "B" "E" "A" X JACK SCREW "F" THREAD X EMI SPRING "D" "C" Part Number Contacts A B C D E F G D #-56 #4-40 #4-40 #6-3 # Quad/Twinax D-Sub Receptacle "A" "B" "D" Contacts are sold separately "C" X JACK POST "F" THREAD "E" (.500) Part Number Contacts A B C D E F # # # #6-3 # Gillette Avenue, Irvine, California Telephone (949) Fax (949)

32 HIGH SPEED RUGGED D-SUBMINIATURE CONNECTORS QUAD/TWINAX PANEL MOUNT D-SUBMINIATURE CONNECTORS Quad/Twinax D-Sub PC Tail "A" "B" "D".5 (TYP) (TYP) Contacts are sold separately X JACK POST "F" THREAD "C" "E" X #-56 UNC-B THREAD.00 MIN (TYP) ±.005 "G" (TYP) Part Number Contacts A B C D E F G #-56 # Gillette Avenue, Irvine, California Telephone (949) Fax (949)

33 SIZE 9 QUADRAX CONTACTS HIGH SPEED RUGGED D-SUBMINIATURE CONTACTS 00 OHM Size 9 Quadrax Pin Contact 00 Ohm Ø Differential Quad SNAP RING Ø.85 MAX For use in P/N: thru Size 9 Quadrax Socket Contact 00 Ohm Differential Quad SNAP RING Ø.85 MAX For use in P/N: thru 006 Size 9 Quadrax Pin Contact PCB Mount 00 Ohm Ø.03 ±.00 ± (TYP) C L 4X Ø.00 Ø.50 4X Ø.035 MIN 4X Ø.05 MIN SNAP RING Ø.67 ±.00 C L.0435 (TYP) MOUNTING HOLE P/N: For use in P/N: thru 3006 Size 9 PC Tail Quadrax Contact 00 Ohm X Ø.04 MIN 4X (TYP) 4X Ø.08 4X.087 PRINTED CIRCUIT 4X Ø.033 MIN.00 (TYP).087 (TYP) P/N: For use in P/N: thru 00 See Page 08 for Cable Assembly Ordering Information 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

34 SIZE 9 TWINAX CONTACTS HIGH SPEED RUGGED D-SUBMINIATURE CONTACTS 00 OHM Size 9 Twinax Pin Contact 00 Ohm Ø Differential Twinax Flexible Twinax Flexible Twinax SNAP RING Size 9 Twinax Socket Contact 00 Ohm.0 Ø.85 MAX For use in P/N: thru Differential Twinax Flexible Twinax Flexible Twinax SNAP RING Ø.85 MAX For use in P/N: thru 006 Size 9 Twinax Pin Contact PCB Mount 00 Ohm.050 Ø ± ± (TYP) CL Ø.50 4X Ø.035 MIN SNAP RING ±.00 Ø.67 X Ø.00 X Ø.05 MIN CL X.065 MOUNTING HOLE P/N For use in P/N: thru 3006 Size 9 PC Tail Twinax Contact 00 Ohm X Ø.04 MIN 4X (TYP) 4X Ø.08.3 PRINTED CIRCUIT 4X Ø.033 MIN.00 (TYP).3 P/N For use in P/N: thru 00 See Page 08 for Cable Assembly Ordering Information Gillette Avenue, Irvine, California Telephone (949) Fax (949)

35 HIGH SPEED BACK PLANE CONNECTORS TWINAX POSITION CONNECTORS 50 OHM FIBRE CHANNEL AND 00 OHM ETHERNET In standard VME cards for low data rate signaling, connectors are widely available to carry non-shielded signaling for the VME bus from the interface via motherboard to daughter card assembly designated as I/O plug-in modules. The industry standard defines these connectors typically as P and P3 connectors. Sabritec has taken the standard housing configuration of the P & P3 mounting dimensions while incorporating true differential pair contacts within the P & P3 dimensional constraints. Data sampling rates exceeding Gbits/second can be driven via matched impedance differential pair interconnections for board-to-board high speed data transfer as well as blind mate I/O plug in modular applications. Sabritec's P connector housing contains position true differential pair blind mate contacts allowing board designers to carry high density differential pair signals from the LRU via motherboard to daughter-card plug in modules with a single connector P type housing. This allows for the use of standard VME bus architecture cages for high speed fibre channel connection. Right Angle Twinax Receptacle Position (Blind Mate PCB Interconnects) 50 Ohm P/N Mates with P/N: Gillette Avenue, Irvine, California Telephone (949) Fax (949)

36 HIGH SPEED BACK PLANE CONNECTORS TWINAX POSITION CONNECTORS/FIBRE CHANNEL 50 OHM CONTACTS Right Angle Twinax Plug Housing Position (Blind Mate PCB Interconnects) 50 Ohm P/N Size 5 Right Angle Twinax Cable Pin Contact 50 Ohm Dimension X Contacts Dim X Differential Twinax Near Row Differential Twinax Near Row Differential Twinax Far Row Differential Twinax Far Row.30 For use in See Page 08 for Cable Assembly Ordering Information Gillette Avenue, Irvine, California Telephone (949) Fax (949)

37 HIGH SPEED BACK PLANE CONNECTORS TWINAX POSITION CONNECTORS 00 OHM ETHERNET Straight Twinax Plug Housing Position (Blind Mate PCB Interconnects) 00 Ohm EMI SPRING GROUND SPACER ALIGMNENT X C L (.645) X #4-40 TAP HOLES X EMI SPRING GROUND.645 X Ø.078 THRU w Ø.8 X CL.0 X (TYP).0 C L (TYP) (.560).0 GROUND SPRING (.490) (.65) (.70) (.95) (.53) P/N Right Angle Twinax Receptacle Position (Blind Mate PCB Interconnects) 00 Ohm X SCREW MNT. & ALIGN. X #4-40 CLINCH NUT MNT/BRACKET.75±.00 (.850) (.75) X Ø.070 PIN.40 (TYP).70.0 X C L C L P/N Size 0 Twinax Pin Contact 00 Ohm Ø For use in Differential Twinax Flexible Twinax X PIN SNAP RING X Ø Gillette Avenue, Irvine, California Telephone (949) Fax (949)

38 HIGH SPEED BLIND-MATE BACK PLANE CONNECTORS FIRWIRE 394b PLUG AND RECEPTACLE Firewire 394b Right Angle Twinax Plug Blindmate Version X.00 4X Ø.05 4X Ø X.00 X Ø.00 GUIDE PINS #9 Twinax Contacts 4 #0 Signal Contacts X #-56 UNC-B THREAD.00 MIN P/N Firewire 394b Twinax Receptacle Blindmate Version 4X.043 SLOTS FOR R/A SOLDERING Ø.05 X T #9 Twinax Contacts 4 #0 Signal Contacts P/N Gillette Avenue, Irvine, California Telephone (949) Fax (949)

39 HIGH SPEED BACK PLANE CONNECTORS FIREWIRE 394b PLUG AND RECEPTACLE Firewire 394b Straight Twinax Plug With Jackposts X EMI SPRING X JACK SCREW #4-40 UNC-A THREAD #9 Twinax Contacts #6 Power Contacts #0 Signal Contacts, P/N Please consult factory for environmentally sealed connectors and associated backshell accessories. Firewire 394b Right Angle Twinax Receptacle With Jackposts X JACK POST #4-40 UNC-B THREAD.50.0 (.00) X X #-56 UNC-B THREAD.00 MIN (.875).075 (.550).3 X Ø.030 X Ø X WAY,.00 (TYP) #9 Twinax Contacts #6 Power Contacts #0 Signal Contacts P/N Gillette Avenue, Irvine, California Telephone (949) Fax (949)

40 HIGH SPEED PANEL MOUNT CONNECTORS RECTANGULAR 8 WAY PLUG AND RECEPTACLE Straight 8 Way Twinax Plug with Removable Twinax Contacts 4X.00 THRU CL.300 4X.00.0 X CL P/N Straight 8 Way Twinax Receptacle with Removable Twinax Contacts X (300).65 (.0) 4X.00 Ø THRU LC.300 4X LC P/N Gillette Avenue, Irvine, California Telephone (949) Fax (949)

41 HIGH SPEED PANEL MOUNT CONNECTORS RECTANGULAR WAY PLUG AND RECEPTACLE Straight Way Twinax Plug with Removable Twinax Contacts.38 X 4X.00 THRU.375 CL.375 4X LC (TYP) (TYP).050 P/N Straight Way Twinax Receptacle with Removable Twinax Contacts X (300).65 (.0) 4X.00 THRU CL 4X CL (TYP) (TYP) P/N Gillette Avenue, Irvine, California Telephone (949) Fax (949)

42 SIZE 8 TWINAX CONTACTS FOR PANEL MOUNT CONNECTORS SIZE 8 TWINAX CONTACTS 00 AND 50 OHM Size 8 Twinax Pin Contact 00 and 50 Ohm.890 Ø.00 X PIN SNAP RING X Ø.050 Part Number Impedance Cable Type Cable Ohm Differential Twinax Ohm Flexible Twinax Ohm Flexible Twinax Ohm Differential Twinax Size 8 Twinax Socket Contact 00 and 50 Ohm.975 X PIN SNAP RING X Ø.050 Part Number Impedance Cable Type Cable Ohm Differential Twinax Ohm Flexible Twinax Ohm Flexible Twinax Ohm Differential Twinax See Page 08 for Cable Assembly Ordering Information Gillette Avenue, Irvine, California Telephone (949) Fax (949)

43 FIBRE CHANNEL/ETHERNET CONNECTORS PCB AND CABLE MOUNT TWINAX CONNECTORS 50 OHM Straight Twinax Cable Connector 50 Ohm WAY.040 SLOT.64 SHRINK.90 SLEEVE Differential Twinax Differential Twinax Right Angle Micro-Miniature D-Sub Twinax Cable Connector 50 Ohm Differential Twinax Differential Twinax WAY.040 SLOT.45 SHRINK SLEEVE Quick Disconnect Twinax Receptacle Right Angle Cable Mount Connector 50 Ohm Differential Twinax Differential Twinax See Page 08 for Cable Assembly Ordering Information 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

44 FIBRE CHANNEL/ETHERNET CONNECTORS PCB AND CABLE MOUNT TWINAX CONNECTORS 50 OHM Straight Twinax PCB Mount Connector 50 Ohm Ø Ø Ø.00 X Ø.04 MIN PRINTED CIRCUIT Ø.40 4X Ø.03 MIN Recommended PCB Hole Pattern P/N Right Angle Micro-Miniature D-Sub Twinax PCB Mount Connector 50 Ohm 4X X Ø.04 MIN Ø.00 Ø.03 Ø X Ø.03 MIN PRINTED CIRCUIT Recommended PCB Hole Pattern P/N Quick Disconnect Twinax PCB Mount Connector 50 Ohm Recommended PCB Hole Pattern P/N Gillette Avenue, Irvine, California Telephone (949) Fax (949)

45 BLIND MATE TWINAX CONNECTORS HIGH SPEED FIBRE CHANNEL SERIES 50 OHM MATCHED IMPEDANCE Blind Mate Right Angle PCB Mount Receptacle 50 Ohm P/N Blind Mate Twinaxial Plug 50 Ohm Mates with Receptacle Only Differential Twinax Differential Twinax Blind Mate Right Angle Twinaxial Plug 50 Ohm Mates with Receptacle Only Differential Twinax Differential Twinax See Page 08 for Cable Assembly Ordering Information 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

46 MICRO TWINAX CONNECTORS NDL/SMA /MICRO-D SIZE PACKAGES Micro Twinax connectors feature matched impedance miniaturized connectors that provide the user with controlled impedance and tightly spaced PCB footprint spacing. These connectors are available in straight or right angle versions. Micro Twinax NDL Size: Replaces standard NDL Triax connector series for higher speed balanced twinax applications Identical NDL footprint PCB pattern for outer conductor spacing (.00" spacing) Applicable for High-Speed Ethernet (00 Base-T) and Fibre Channel ( GBit/sec min.) applications Z 0 = 00 Ohm or 50 Ohm Differential Pair Impedance NDL Size Micro Twinax SMA Size Package: Package size of a standard SMA series connector housing Differential pair matched impedance of Z 0 = 00 or 50 ohm balanced impedance between conductors Applicable for High-Speed Ethernet (00 Base-T) and ( GBit/sec min.) applications Z 0 =00 Ohm or 50 Ohm Differential Pair Impedance Micro Twinax Micro-D Size Package: Package size mimics Micro-D packaging constraints throughout connector pair Matched impedance 00 or 50 ohm balanced impedance throughout connector pair Applicable for High-Speed Ethernet (00 Base-T) and Fibre Channel ( GBit/sec min.) applications Z 0 =00 Ohm or 50 Ohm Differential Pair Impedance Micro-D Size Micro Twinax NDL Plug Micro Twinax NDL Straight Jack PCB Mount Gillette Avenue, Irvine, California Telephone (949) Fax (949)

47 MICRO TWINAX CONNECTORS NDL SIZE PACKAGE MATCHED IMPEDANCE 00 AND 50 OHM MICRO TWINAX SERIES Micro Twinax NDL Straight Cable Plug 00 and 50 Ohm # # # # WAY X Ø.05 X Ø.00 Ø.95 MAX #0-3 UNF-B 0-3 UNF-A HEX COUPLING NUT SHRINK SLEEVE Micro Twinax NDL Bulkhead Mount Jack 00 and 50 Ohm.5 PANEL /4-36 UNS-A THD 5/6 HEX NUT O-RING.300 Ø.45 MAX 3/8 HEX SHRINK SLEEVE.35 MIN.50 MIN MOUNTING "D" HOLE Part Number Impedance Cable Type Cable Ohm Differential Twinax Ohm Flexible Twinax Ohm Flexible Twinax Ohm Differential Twinax Part Number Impedance Cable Type Cable Ohm Differential Twinax Ohm Flexible Twinax Ohm Flexible Twinax Ohm Differential Twinax Micro Twinax NDL Straight Jack 00 and 50 Ohm PCB Mount # #.050 X Ø.05 X Ø Ø UNF-A THD.50 X Ø.00 (00 OHM) X Ø.0 (50 OHM) 4X Ø.030 MAX X Ø.033 MIN.050 PRINTED CIRCUIT X Ø.05 MIN (00 OHM) X Ø.06 MIN (50 OHM) Part Number Impedance Ohm Ohm Micro Twinax NDL Right Angle Jack 00 and 50 Ohm PCB Mount # #.49 X Ø.05 X Ø UNF-A THD X Ø.033 MIN X Ø.05 MIN (00 OHM) X Ø.06 MIN (50 OHM) Part Number Impedance Ohm Ohm # #.87 PRINTED CIRCUIT 4X Ø.030 MAX X Ø.00 (00 OHM) X Ø.0 (50 OHM) See Page 08 for Cable Assembly Ordering Information 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

48 MICRO TWINAX CONNECTORS SMA SIZE TWINAX CONNECTORS 00 AND 50 OHM MATCHED IMPEDANCE Micro Twinax SMA Size Plug 00 or 50 Ohm Matched Impedance Part Number Differential Impedance Cable Type Cable Ohm Differential Twinax Ohm Flexible Twinax Ohm Flexible Twinax Ohm Differential Twinax Ohm Differential Twinax Micro Twinax SMA Size Straight Jack 00 or 50 Ohm Matched Impedance Part Number Impedance Ohm Ohm Micro Twinax SMA Right Angle Jack Straight PCB Mount 00 or 50 Ohm Matched Impedance Part Number Impedance Ohm Ohm See Page 08 for Cable Assembly Ordering Information Gillette Avenue, Irvine, California Telephone (949) Fax (949)

49 MICRO TWINAX CONNECTORS MICRO-D SIZE TWINAX CONNECTORS 00 AND 50 OHM MATCHED IMPEDANCE Micro-D Twinax Straight Plug 00 or 50 Ohm Matched Impedance Part Number Impedance Cable Type Cable Ohm Differential Twinax Ohm Differential Twinax Mates with and 004 ONLY Micro-D Twinax Straight Jack PCB 00 or 50 Ohm Matched Impedance.300 X Ø X Ø.08 X Ø.00 MIN Part Number Impedance Ohm Ohm PRINTED CIRCUIT 4X Ø.033 MIN Mates with P/N: and 006 ONLY Micro-D Twinax Right Angle Plug 00 or 50 Ohm Matched Impedance Part Number Impedance Cable Type Cable Ohm Differential Twinax Ohm Differential Twinax Mates with P/N: and 003 ONLY Micro-D Twinax Right Angle Jack PCB Mount 00 or 50 Ohm Matched Impedance X Ø X Ø PRINTED CIRCUIT X Ø.00 MIN.50 4X Ø.033 MIN Part Number Impedance Ohm Ohm.075 See Page 08 for Cable Assembly Ordering Information 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

50 MICRO QUADRAX CONNECTORS QUADRAX PLUG AND RIGHT ANGLE PC CABLE MOUNT Micro Quadrax Plug 00 Ohm.450 MAX Ø MAX WAY HEX 5/6-3 UNEF-B Differential Quad Micro Quadrax Right Angle PCB Mount Receptacle 00 Ohm.7000 (.700) CL (.50) 4X.05 4X X.00 CL 4X Ø.05 MIN LC UNEF-A 4X Ø.08 4X Ø.00 4X Ø.035 MIN P/N See Page 08 for Cable Assembly Ordering Information Gillette Avenue, Irvine, California Telephone (949) Fax (949)

51 MODULAR BLOCK CONNECTOR (MBC) SERIES MODULAR BLOCK CONNECTORS 00 OHM TWINAX PLUG AND RECEPTACLE Sabritec s Modular Block connectors feature dual twinax blindmate assemblies that permit the transmit and receive of high speed Ethernet data rate signals in one connector. This series allows for modularity in PCB routing of high speed signaling. Modular Block Connectors are true 00 ohm differential pair matched impedance and are optimized for maximum space utilization, modularity and true signal integrity. Modular Block Straight Twinax Plug Ø (.575) X JACK SCREW #-56 UNA-B LC.6 LC.875 P/N Modular Block Straight Twinax Receptacle PCB Mount CL.67 4X Ø X #-56 TAP HOLES X.50 MIN X JACK POST #-56 UNC-B CL.56 HEX LC LC.05.0 (TYP) X Ø.00 MIN.095 CL X.05 PRINTED CIRCUIT X Ø.034 MIN GROUND P/N Size 0 Twinax Socket Contact Crimp Termination Differential Twinax SHRINK SLEEVE See Page 08 for Cable Assembly Ordering Information 7550 Gillette Avenue, Irvine, California Telephone (949) Fax (949)

52 CABLE ASSEMBLY ORDERING INFO PART NUMBER TABLE Cable Length in Inches (XXX) Connector # OL - For Open Lead Cable Group # Flexible Twinax = M7/ = = = = Connector # SAMPLE P/N: /3/ /8 Connector # Sz. 8 Twinax Pin Connector # Sz. 8 Twinax Socket Differenital Pair 6 = = = Differential Quad 9 = = = Please use the request for quote worksheet on page 5 to specify your custom application needs. 4" Cable Group No Cable Designation Flexible Twinax Cables Manufacturer Impedance (OHMS) Jacket Conductor (DIA) M7/ Mil-Spec " 0.04" Sabritec " 0.09" Sabritec " 0.04" W.L. Gore " 0.00" W.L. Gore 00 0." 0.06" Differential Pair Twinax Cables Cable Group No. Cable Designation Impedance (OHMS) Jacket Conductor (DIA) Differential: 50 Sig. To Shield: " x 0.60" 0.04" Stranded Differential: 50 Sig. To Shield: " x 0.4" 0.00" Solid Differential: 00 Sig. To Shield: " x 0.30" 0.09" Stranded Cable Group No. Differential Quad Cables Cable Designation Impedance (OHMS) Jacket Conductor (DIA) Differential: 50 Sig. To Shield: 75 Differential: 50 Sig. To Shield: 75 Differential: 00 Sig. To Shield: " 0.03" 0.90" 0.00" 0.75" 0.05" Gillette Avenue, Irvine, California Telephone (949) Fax (949)