General Specifications

Transcription

1 35A/MDL, 32A/MDL Controllers General Specifications l tiona Func ment nce Enha (Mount on DIN Rail) GS 05P0D80EN n Overview The 35A/MDL and 32A/MDL controllers can be mounted in a panel. A ladder sequence function is included as standard. The short depth of the controller helps save instrument panel space. The 35A/ 32A also support open networks such as Ethernet communication. n Features Simple panel surface Mounting the controller in a panel simplifies the panel surface. Ladder sequence function is included as standard. This function allows for creating a simple sequence control. Dedicated LL50A Parameter Setting Software (sold separatly) allows for performing programming using a ladder language. Various builtin open network functions such as Ethernet are available. Easy connection with various vendors PLCs is possible. (32A support CCLink and RS485 communication only.) Quick setting function Setting only the minimum necessary parameters for operation is possible. Equipped with a multitude of functions Universal I/O and retransmission output are included as standard. PID control, heating/cooling control, etc. are available. LL50A Parameter Setting Software (sold separately) The parameters and ladder programs of Advanced controller can be built from a PC using this software. It makes data management even easier. n Functional Specifications Control Specifications () Control Mode Singleloop control (2) Control period 200 ms Table of Number of Inputs and Outputs Model and suffix code (See the model code) Number of analog input points Number of analog output points (*) Number of contact input points Number of contact output points (*3) 0 /MDL 2 /MDL (*2) /MDL /MDL A 32A *: *2: *3: 35A/MDL 32A/MDL n Control Computation Function () Types of control PID control ON/OFF control Twoposition twolevel control (*4) Heating and cooling control (*4) *4: Selectable for heating and cooling control (2) Control Computation Function (a) Target setting point and the number of PID parameter groups Respectively, four sets of target setpoints, alarm setpoints, and PID parameters can be set. (b) Selecting the PID parameter group The following PID parameter groups can be selected. Target setpoint number (SPNO) (The PID number can be set arbitrarily.) Measured input zone PID Target setpoint zone PID Reached target setpoint zone PID (c) Autotuning Tuning results can be selected from two options, Normal or Stable. Tuning output limit can be set. (It cannot be used in heating/cooling control.) (d) Super function: Overshootsuppressing function (e) Super 2 function: Huntingsuppressing function (f) STOP preset output function (g) Input ERROR preset output function (h) MANUAL preset output function (3) Operation Mode Switching Operation mode switching AO/MANUAL and RUN/STOP switching REMOTE/LOCAL switching (only model with communication option) Excluding control output The analog output point can be used as either cooling control output or transmission output. Excluding control output relays Yokogawa Electric Corporation 2932, Nakacho, Musashinoshi, Tokyo, Japan Tel.: Fax.: GS 05P0D80EN st Edition Mar.3, 205 (YK)

2 2 (4) Control Parameter Setting Range Proportional band 0. to 999.9% Integral time to 6000 sec. or OFF (using manual reset) Derivative time to 6000 sec. or OFF ON/OFF control hysteresis (one or two 0.0 to 00.0% of measured input range width hysteresis points) Preset output 5.0 to 05.0% (however, 0 ma or less cannot value be output) High/low output 5.0 to 05.0% limiter Low limit setpoint < high limit setpoint Tight shut function Rateofchange limiter of output Output deadband Alarm Functions Types of Alarm Measured value alarm Deviation alarm Rateofchange alarm When manual control is carried out with 4 to 20 ma output, control output can be reduced to about 0 ma. 0. to 00.0%/sec., OFF For heating and cooling control: 00.0 to 50.0% PV (measured value) high/low limit alarm Deviation high/low limit alarm Deviation high and low limits alarm Deviation within high and low limits alarm Analog input PV high/low limit alarm PV rateofchange alarm SP (setpoint) high/low limit alarm Target SP high/low limit alarm Setpoint alarm Target SP deviation high/low limit alarm Target SP deviation high and low limits alarm Target SP deviation within high and low limits alarm Control output high/low limit alarm Output alarm Cooling control output high/low limit alarm Selfdiagnosis alarm Other alarms FAIL Alarm Functions Alarm output action Number of alarm settings Number of alarm output points Alarm standby action Alarm latch (forced reset) function Alarm hysteresis Alarm ON/OFF delay timer 4 Up to 8 (differs by model code) Contact I/O Function This function allows for allocating the input error condition, operation condition, alarm condition or other conditions to the contact input and contact output. Contact input Contact output AO/MANUAL switching REMOTE/LOCAL switching (only model with communication option) STOP/START switching Switching to AO Switching to MANUAL Switching to REMOTE (only model with communication option) Switching to LOCAL (only model with communication option) AOTUNING START/STOP switching SP number specification PID number specification Manual preset output number specification Alarms through 4 Status output Ladder Sequence Function () Number of I/O Points 35A/MDL 32A/MDL Number of digital input points Up to 7 Up to 2 Number of digital output points Up to 8 Up to 3 This is limited by the number of contact I/O signal points. (See the model code.) (2) Types of Command Number of commands Remark Number of basic Load, AND, OR, Timer, 3 command types Counter, etc. Comparison, reverse, addition/ Number of application command types division, logic operation, high/ subtraction/multiplication/ 73 low limiter, etc. (3) Sequence Device Types of device Number of points Digital I/O Input relay 7 (max) Output relay 8 (max) M relay (bit data) 256 Internal device DAT register (data) 28 P register (parameter) 0 K register (constant) 30 Special device Special relay (bit data) 2 Process data and process relay can be used besides the abovementioned. (4) Program capacity Max Program capacity: 300 steps * *: Available number of steps differs according to the parameters and using command. (5) Ladder computation period Ladder computation period is the same as control period.

3 Communication Function Modbus/TCP Modbus (RTU/ASCII) PROFIBUSDP CCLink DeviceNet Peer to peer Coordinated Communication Function Method Interface Targets Max connection Communication Data Server Ethernet PLC and others 2 connections : Gateway Ethernet 75A/55A/52A/ + 35A/32A/UP55A/ 3 units UP35A/UM33A (*) A standard industry protocol allowing communications between the controller and devices such as PCs, PLCs, and DCSs. Used for communication between PLCs and remote I/O, enabling highspeed data transmission. A protocol allowing multiple controllers to send and receive data between one another. The Ladder Program is used. A protocol to coordinate the operation of two or more instruments controlling the same Slave PLC and others, 75A/55A/52A/ 35A/32A/UP55A/ UP35A/UP32A/UM33A (*2) Slave PLC and others Modbus master function 75A/55A/52A/ 35A/32A/UP55A/ UP35A Slave PLC and others Modbus master function 75A/55A/52A/ 35A/32A/UP55A/ UP35A\UP32A/UM33A Slave PLC and others Modbus master function Multidrop Master/Slave (2 wire only) process. The proprietary Yokogawa protocol allowing communications to PCs, PLCs and touch panels. Slave 75A/55A/52A/ 35A/32A/UP55A/ UP35A 75A/55A/52A/ 35A/32A/UP55A/ UP35A/UP32A 75A/55A/52A/ 35A/32A/UP55A/ UP35A/UP32A/ UM33A (*2) PC and others, 75A/55A/52A/ 35A/32A/UP55A/ UP35A/UP32A/ 3 units Number of nodes: 26 3 Units (Main Controller is included.) Number of nodes: 42 (Remote device) 3 Units (Main Controller is included.) Number of nodes: 64 3 Units (Main Controller is included.) Read/Write: 4 units Read only : 28 units Master : unit Slave : 3 units PV, SP, O, ALM etc PC link 3units Ladder A protocol to communicate to PLCs. UM33A (*2) *: digital indicating controller, Signal conditioner JUXTA, Power monitor POWERCERT can be connected. *2: digital indication controllers can be connected. Physical Interface Ethernet Standard : IEEE802.3 (0BASET, 00BASETX) Max segment length : 00m Max. Connecting Configguration : Cascade Max. 4 level (0BASET), Max. 2 level (00BASETX) PROFIBUSDP Standard : EIA Communication method : Twowire harfduplex or fourwire harfduplex, startstop synchoronization, and nonprocedural Baud rate : 600,200,2400,4800,9600,9200 or 38400bps, Peer to peer communication is fixed at 9200bps Maximum communication distance : 200m Terminating resistor : 220Ω (External) Standard : Field bus (IEC658) Corresponding version : DP V0 Baud rate : 9.6k, 9.2k, 45.45k, 93.75k, 87.5k, 0.5M,.5M, 3M, 6M, 2M, AO (*3) Communication distance : 200m (9.6k to 93.75k) 000m (87.5k) 400m (0.5M) 200m (.5M) 00m (3M to 2M) *3: AO automatically sets the baud rate to that of the host controller (PROFIBUSDP master). CCLink Supported version : Remote device (Ver..0, Ver.2.00) Baud rate : 56k, 625k, 2.5M, 5M, 0M bps Transmission distance :.2km (56k bps), 600m (625k bps), 200m (2.5M bps), 50m (5M bps), 00m (0M bps) When using optical repeater : 7.6 km (56k) to 4.3 km (0M) DeviceNet Field bus (IEC658) Baud rate 25k, 250k, 500k bps Transmission distance 500m (25k bps), 250m (250k bps), 00m (500k bps) 3

4 4 Hardware Specifications Display Specifications The controller status can be verified with the LED. Status LED Lit/Blinks Description Normal Green Lit Communication error Green Blinks Instrument failure Red Lit Parameter error/ Hardware failure/ladder program corruption. Input error Red Blinks sensor burnout, input over 35A/MDL Front (with terminal cover) LED lamp 32A/MDL Front (with terminal cover) Universal Input Specifications Number of input points: Types of input, instrument range, and measurement accuracy (see the table below) Types of input Instrument range C F Accuracy to C to F ±0.% of instrument K to C to F range ± digit for 0 C to C to F or more J to C to F ±0.2% of instrument to C to F range ± digit for less than 0 C However, ±2% of instrument range T ± digit for less than 0.0 to C to F 200 C of thermocouple K ±% of instrument range ± digit for less than 200 C of thermocouple T ±0.5% of instrument range ± digit for 400 C B 0.0 to C 32 to 3300 F or more ±5% of instrument range ± digit for less than 400 C S 0.0 to C 32 to 300 F ±0.5% of instrument R 0.0 to C 32 to 300 F range ± digit ±0.% of instrument range ± digit N to C to F ±0.25% of instrument range ± digit for less than 0 C E to C to F ±0.% of instrument L to C to F range ± digit for 0 C to C to F or more ±0.2% of instrument range ± digit for less U than 0 C 0.0 to C to F However, ±.5% of instrument range ± digit for less than C of thermocouple E W (*2) 0.0 to C 32 to 4200 F ±0.2% of instrument range ± digit Platinel ±0.% of instrument 0.0 to C 32.0 to F 2 range ± digit ±0.5% of instrument range ± digit for 800 C PR to C 32 to 3400 F or more Accuracy not guaranteed for less than 800 C Thermocouple Resistancetemperature detector (RTD) 3wire W97 Re3W to C 32 to 3600 F Re to C to F JPt to C to F Pt00 ±0.2% of instrument range ± digit ±0.% of instrument range ± digit (*) ±0.% of instrument range ± digit to C to F ±0.% of instrument to C to F range ± digit (*) to C to F ±0.% of instrument range ± digit to V Standard.000 to V signal 4.00 to ma to V DC voltage 0.00 to 0.00 V 0.00 to mv DC current 0.00 to ma ±0.% of instrument range ± digit The accuracy is that in the standard operating conditions: 23 ±2 C, 55 ±0%RH, and power frequency at 50/60 Hz. *: ±0.3 C and ± digit in the range between 0 and 00 C ±0.5 C ± digit in the range between 00 and 200 C *2: W5% Re/W26% Re (Hoskins Mfg.Co.), ASTM E988 Applicable standards: JIS, IEC and DIN (ITS90) for thermocouples and resistancetemperature detectors (RTD) Input sampling period: Synchronized to control period

5 5 Burnout detection Upscale and downscale of function, and OFF can be specified for the standard signal of thermocouple and resistancetemperature detector (RTD). For integrated signal input, 0. V or 0.4 ma or less is judged as a burnout. Input bias current: 0.05 μa (for thermocouple and resistancetemperature detector (RTD)) Resistancetemperature detector (RTD) measured current: About 0.6 ma Input resistance MΩ or more for thermocouple/mv input About MΩ for voltage input About 250 Ω for current input (with builtin shunt resistance) Allowable signal source resistance 250 Ω or less for thermocouple/mv input Effect of signal source resistance: 0. μv/ω or less 2 kω or less for DC voltage input Effect of signal source resistance: about 0.0%/00 Ω Allowable wiring resistance Up to 50 Ω per line for resistancetemperature detector (RTD) input (conductor resistance between the three lines shall be equal) Effect of wiring resistance: ±0. C/0 Ω Allowable input voltage/current ±0 V DC for thermocouple/mv/ma or resistancetemperature detector (RTD) input ±20 V DC for V input ±40 ma DC for ma input Noise reduction ratio 40 db or more (at 50/60 Hz) in normal mode 20 db or more (at 50/60 Hz) in common mode Reference junction compensation error ±.0 C (5 to 35 C) ±.5 C (0 to 5 C and 35 to 50 C) Contact Input Specifications Number of points: 2 points (standard) For the maximum number of points, see the model and suffix code table. Input type: novoltage contact input or transistor contact input Input contact capacity: 2 V DC, 0 ma or more Be sure to use a contact with a minimum ON current of ma or more ON/OFF detection For novoltage contact input: Contact resistance kω or less in ON state Contact resistance 50 kω or more in OFF state Transistor contact input: 2 V or less in ON state Leak current 00 μ A or less in OFF state Status detection minimum hold time: control period + 50 ms Application: SP switching, operation mode switching, event input Analog Output Specifications Number of points Control output (heatingside output): point (standard), which is shared with transmission output Coolingside output: point, which is shared with transmission output Output functions Current output or voltage pulse output Current output 4 to 20 ma DC or 0 to 20 ma DC/load resistance 600 Ω or less Current output accuracy ±0.% of span (however, ±5% of span for ma or less) The accuracy is that in the standard operating conditions: 23 ±2 C, 55 ±0%RH, and power frequency at 50/60 Hz Voltage pulse output Application: time proportional output ON voltage: 2 V or more/load resistance of 600 Ω or more OFF voltage: 0. V DC or less Time resolution: 0 ms or 0.% of output value, whichever is larger Retransmission Output Specifications Number of points: point (standard), which is shared with 5 V DC loop power supply Additional points when analog control output are not used Output function: current output 4 to 20 ma DC or 0 to 20 ma DC/load resistance 600 Ω or less Current output accuracy (conversion accuracy from PV value on the set scale): ±0.% of span (however, ±5% of span for ma or less) The accuracy is that in the basic operating conditions: 23 ±2 C, 55 ±0%RH, and power frequency at 50/60 Hz This is not conversion accuracy through input and output but the performance of transmission output itself. 5V DC Loop Power Supply Specifications Number of points: point (standard), which is shared with retransmission output Control output ( point) can also be used. Supply voltage: 4.5 to 8.0 V DC Maximum supply current: about 2 ma (with shortcircuit current limiting circuit) Step Response Time Specifications Within s (Response time at 63% of transmission output when a change is made stepwise in the range between 0 and 90% of input span) Relay Contact Output Specifications Types of contact and number of points Control relay output: one ccontact point Control output of heating and cooling control: 2, acontact points Alarm output: 3 acontact points (Common is separated) Contact rating ccontact: 3 A at 250 V AC or 3 A at 30 V DC (resistance load) acontact: For alarm output: A at 240 V AC or A at 30 V DC (resistance load) For output of heating and cooling control relay output: 3 A at 240 V AC or 3 A at 30 V DC (resistance load) *: The control output should always be used with a load of 0 ma or more. The alarm output should always be used with a load of ma or more.

6 6 Application: time proportional output, alarm output, FAIL output, etc. Time resolution for control output: 0 ms or 0.% of output value, whichever is larger Transistor Contact Output Specifications Number of points: see the model and suffix code table Output form: open collector (sink current) Output contact capacity: Up to 24 V DC, 50 ma Output time resolution: min 200 ms Application: alarm output, FAIL output, etc. Heater Break Alarm Specifications (for /HA Option) Function: Measures the heater current using an external current transformer (CT) and generates a heater break alarm when the measured value is less than the disconnection detection value. Number of input points: 2 points Number of output points: 2 points (transistor contract output) CT input resistance: about 9.4 Ω CT input range: 0.0 to 0. Arms (0.2 Arms or more cannot be applied) Heater current alarm setting range: OFF, 0. to Arms Heater current measured value display range: 0.0 to Arms *: The CT ratio can be set. CT ratio setting range: to 3300 Recommended CT: CT from URD Co. Ltd. CTL6SH: CT ratio 800, measurable current range: 0. to 80.0 Arms CTL2L30: CT ratio 3000, measurable current range: 0. to 80.0 Arms Heater current measurement period: 200 ms Heater current measurement accuracy: ±5% of CT input range span ± digit (CT error is not included) Heater current detection resolution: Within /250 of CT input range span Disconnection detection ON time: Minimum 200 ms. (for time proportional output) 24 V DC Loop Power Supply Specifications (for /LP Option) Application: Power is supplied to the 2wire transmitter. Supply voltage: 2.6 to 28.0 V DC Rated current: 4 to 20 ma DC Maximum supply current: About 30 ma (with shortcircuit current limiting circuit) Maintenace Port Specifications The maintenance port is used to connect a dedicated cable when using the LL50A Parameter Setting Software (sold separately). Through this port, you can set controller parameters, download ladder programs, and so on. For details, see the LL50A General Specifications (GS05P05A00EN). Dedicated cable To USB terminal LL50A Parameter Setting Software Use LL50A with the controller turned on. (The dedicated cable must be connected. LL50A Lightloader adapter cannot be used.) The maintenance port is not isolated from the PV input terminal. Use the port only for maintenance purposes, such as for setting the controller parameters. Safety and EMC Standards Safety: Compliant with IEC/EN600 (CE), IEC/EN600 0 (CE), approved by CAN/CSA C22.2 No. 600 (CSA), approved by UL600. Controller with DIN rail (option /MDL): CE marking scheduled Installation category: II Pollution degree: 2 Measurement category: I (CAT I) (UL, CSA) O (Other) (CE) Rated measurement input voltage: Max. 0 V DC Rated transient overvoltage: 500 V (*) *: This is a reference safety standard value for measurement category I of IEC/EN/CSA/UL600. This value is not necessarily a guarantee of instrument performance. EMC standards: Compliant with CE marking EN 6326 Class A, Table 2 (For use in industrial locations), EN *: The instrument continues to operate at a measurement accuracy of within ±20% of the range during testing. EN 550 Class A, Group EN Class A EN EMC Regulatory Arrangement in Australia and New Zealand EN 550 Class A, Group KC marking: Electromagnetic wave interference prevention standard, electromagnetic wave protection standard compliance

7 7 Power Supply Specifications and Isolation Power supply Rated voltage: 00 to 240 V AC (+0%/5%), 50/60 Hz 24 V AC/DC (+0%/5%) (When the /DC option is specified) Power consumption: 35A/MDL: 8 VA (For the /DC option. DC: 9 VA, AC: 4 VA) 32A/MDL: 5 VA (For the /DC option. DC: 7 VA, AC: VA) Storage: Nonvolatile memory Allowable power interruption time: 20 ms (at 00 V AC) Withstanding voltage 2300 V AC for minute between primary and secondary terminals (UL, CSA) 3000 V AC for minute between primary and secondary terminals (CE) 500 V AC for minute between primary terminals 500 V AC for minute between secondary terminals (Primary terminals = Power (*) and relay output terminals, Secondary terminals = Analog I/O signal terminals, contact input terminals, communication terminals, and functional grounding terminals.) *: Power terminals for 24 V AC/DC models are the secondary terminals. Insulation resistance Between power supply terminals and a grounding terminal: 20 MΩ or more at 500 V DC Isolation specifications Transportation and Storage Conditions Temperature: 25 to 70 C Temperature change rate: 20 C per hour or less Humidity: 5 to 95%RH (no condensation) Effects of Operating Conditions Effect of ambient temperature For voltage or TC input: ± μ V/ C or ±0.0% of F.S. (instrument range)/ C, whichever is greater For RTD input: ±0.05 C/ C (ambient temperature) or less For current input: ±0.0% of F.S. (instrument range)/ C For analog output: ±0.02% of F.S./ C or less Effect of power supply fluctuation: For analog input: ±0.05% of F.S. (instrument range) or less For analog output: ±0.05% of F.S. or less (Each within rated voltage range) PV (universal) input terminal, Maintenance port Control and transmission (analog) output terminal (not isolated between the analog output terminals) Control relay (ccontact or 2 acontact) output terminal Alarm relay (acontact) output terminal Alarm2 relay (acontact) output terminal Alarm3 relay (acontact) output terminal Contact input terminal (All) RS485 communication terminal (2 ports) 24 V DC loop power supply terminal Contact output (transistor) terminal Ethernet/PROFIBUSDP/CCLink/DeviceNet communication terminal Internal circuits Power supply The circuits divided by lines are insulated mutually. Environmental Conditions Normal operating conditions Ambient temperature: 0 to 50 C If the CCLink option is specified, 0 to 50 C for 35A/MDL; 0 to 40 C for 32A/MDL. (sidebyside mounting: 0 to 50 C for 55A/MDL; 0 to 40 C for 52A/MDL) Ambient humidity: 20 to 90% RH (no condensation) Magnetic field: 400 A/m or less Continuous vibration (at 5 to 9 Hz) Half amplitude of.5 mm or less (at 9 to 50 Hz) 4.9 m/s 2 or less, oct/min for 90 minutes each in the three axis directions Rapid vibration: 4.7 m/s 2, 5 s or less Impact: 98 m/s 2 or less, msec. Installation altitude: 2,000 m or less above sea level Warmup time: 30 minutes or more after the power is turned on Startup time within 0 s

8 8 Block Diagram Single Loop Control Equipped as standard PV input Equipped as standard. Contact inputs PV DI DI2 Input type Input unit Input range/scale IN UNIT RH, RL SDP SH, SL Input ladder calculation program (signal goes to the control computation as is when without ladder program). For ladder program, see the LL50A Parameters Setting Software User s Manual. PV input bias PV input filter BS FL Communication Ratio bias computation RT RBS SPNO SP Target setpoints to 4 REMOTE LOCAL R/L SP limiter SP ramp rate SPH, SPL UPR, DNR TMU PV SP Control computation CNT ALG Input error preset output Manual preset output Manual operation Output limiter EPO Normal When sensor burnout occurs MPON OH, OL Output limiter OH, OL OLMT MAN AO A/M AO (ON)/MAN (OFF) switch Preset output PO STOP S/R RUN STOP (ON)/RUN (OFF) switch Output terminal assignment OT O retransmission output ORS * After the control output terminal is specified by the parameter OT, other current output terminals can be used as retransmission output. Equipped as standard RET retransmission output RTS Equipped as standard Alarm Output ladder calculation program (signal goes to the output as is when without ladder program). For ladder program, see the LL50A Parameter Setting Software User s Manual. For optional suffix code /LP 24 V loop power supply Alarm (PV high limit) Alarm 2 (PV low limit) Alarm 3 (PV high limit) For 32A with optional suffix code /HA Heater break alarm LPS O O RET AL AL2 AL3 Relay Current or voltage pulse (Current when retransmission output) Legend Current HAL Heater break alarm HAL2 Heater break alarm 2 Terminal Parameter Function Analog signal Contact signal

9 9 Terminal Arrangement Terminal Arrangement for 35A/MDL Single Loop Control Control output O (Suffix code: Type=0) Relay contact output Factory default: Control output is relay. NC 0 NO Contact rating: 250 V AC, 3 A 30 V DC, 3 A (resistance load) Heating/cooling control output Heating/cooling relay contact output (Suffix code: Type =2) Cooling O2 NO side 0 Heating O NO side Contact rating: 240 V AC, 3 A 30 V DC, 3 A (resistance load) Contact output ALM (Equipped as standard) External contact output (relay) Alarm3 output (PV high limit) 04 AL3 Common 05 Alarm2 output 06 ( PV low limit) AL2 Common 07 Alarm output (PV high limit) 08 AL Common 09 Relay contact rating: 240 V AC, A 30 V DC, A (resistance load) Power supply V AC power supply 24 V AC/DC power supply Factory default: PV input type is undefined PV input TC input Current (ma) input E4terminal area (Equipped PV as standard) RTD input A 20 b 202 B Voltage (mv, V) input E3terminal area Eterminal area Retransmission output RET (Equipped as standard) Retransmission output 5 V DC loop power supply Can be used for 5 V DC loop power supply when not used for Default: PV retransmission retransmission output ma DC or V DC 020 ma DC (Max. 2 ma DC) Load resistance 600 Ω or less Default: 420 ma DC Coolingside control output RET/O2 (Suffix code: Type =2) Current/voltage pulse output Can not be used for retransmission output or + 5 V DC loop power supply when ma DC, current/voltage pulse output is used. 420 ma DC, Voltage pulse (2V) Can be used for retransmission output or 5 V 206 DC loop power supply when control output is not used. Current output range can be changed. Control output O (Suffix code: Type=0 or 2) Current/voltage pulse output Retransmission output 5 V DC loop power supply ma DC, 420 ma DC, Voltage pulse (2 V) 208 Default: Undefined ma DC, 420 ma DC 208 Default: 420 ma DC V DC (Max. 2 ma DC) 208 Can be used for retransmission output or 5 V DC loop power supply when current/voltage pulse output is not used for control output. Current output range can be changed. Contact input DI (Equipped as standard) External contact input Novoltage contact Transistor contact STOP when DI2=ON 20 DI2 RUN when DI2=OFF AO when DI=ON 2 DI MAN when DI=OFF 22 Common +5V DI V DI 2 22 N 0 N 0 Contact rating: 2 V DC, 0 ma or more Function can be assigned to the terminals with no function. L L Allowable range: (24 V AC/DC power supply: Optional suffix code /DC) V AC (+0%/5%) (free voltage) 50/60 Hz shared

10 0 E4terminal area Eterminal area Contact input DI (Suffix code: Type 2=2) Common Factory default: No function Factory default: No function Factory default: No function Factory default: No function Factory default: No function Novoltage contact ETerminal Area External contact input DI 303 DI2 304 DI3 305 DI4 306 DI5 Transistor contact 30 +5V DI V DI2 303 DI3 +5V 304 DI4 +5V 305 DI5 +5V E4Terminal Area Contact output DO (Suffix code: Type 2=2) External contact output Factory default: No function DO45 50 Factory default: No function DO Factory default: No function DO Factory default: No function DO Factory default: No function DO4 505 Common E3terminal area 2 22 Contact rating: 2 V DC, 0 ma or more Function can be assigned to the terminals with no function. Transistor contact rating: 24 V DC, 50 ma Function can be assigned to the terminals with no function. 24 V DC loop power supply LPS24 (Optional suffix code /LP) V DC (Max. 30 ma DC) V DC loop power supply 4042 E3Terminal Area communication RS485 (Suffix code: Type 3=) SDB(+) 407 Ethernet communication (with gateway function) 0BASET/00BASETX ETHR RJ45 connector (Suffix code: Type 3=2) SDA() 408 SG 409 RDB(+) 40 RDA() 4 Upper side LED (baud rate) Color Amber Lit 00M bps Unlit 0M bps Lower side LED (link activity) Color Green Lit Linked Blink Active Unlit Link failure RSB(+) 407 RSA() 408 SG 409 PROFIBUSDP communication (with Modbus master) VP PROF Data 390Ω CHK line (Suffix code: Type 3=4) 2 RxD/TxDP RDY 3 Data 220Ω If the is located at the end ERR line 4 RxD/TxDN of a segment for the 390Ω PROFIBUS 5 DGND communication wiring, terminating resistors are Pin Signal name Description separately needed. VP +5V bus power These are to be prepared by Data signal users. (390 Ω: 2 pcs. 220 Ω: 2 RxD/TxDP (positive data receive/transmit) pc., or an active Data signal terminator.) 3 RxD/TxDN (negative data recive/transmit) 4 DGND Signal ground 5 SHIELD Shield ground LED Lit Unlit CHK (red) User profile error Normal RSB(+) 407 No power, or Communication Normal RDY Communicating (green) successfully ERR (red) Not connected, or communication failure (flashing) failure Normal RSA() 408 SG 409 CCLink communication (with Modbus master) DA CHK 0Ω 2 DB 3 L ERR 4 L RUN 5 Pin Signal name Description FG Flame ground 2 SLD Shield 3 DG RX/TX signal ground 4 DB RX/TX signal 5 DA LED CHK (red) L ERR (red) L RUN (green) RX/TX + signal Lit Unlit User profile error/ Address error Normal Communication failure (CRC error) Normal No carrier Normal detected/ Communicating successfully Communication timeout CCL (Suffix code: Type 3=3) If the is located at the end of a segment for the CCLink communication wiring, terminating resistors are separately needed. These are to be prepared by users. (0 Ω: pc.) RSB(+) 407 RSA() 408 SG 409 DeviceNet communication (with Modbus master) CAN_H DNET 2Ω (Suffix code: Type 3=5) 2 CHK CAN_L 3 If the is located at 4 the end of a segment MNS for the DeviceNet 5 communication wiring, terminating resistors Pin Signal name Description are separately needed. V+ DeviceNet power supply 24V These are to be 2 CAN_H RX/TX + signal prepared by users. 3 DRAIN Shield/Drain wire (2 Ω: pc.) 4 CAN_L RX/TX signal 5 V DeviceNet power supply common LED Lit/flashing Unlit CHK (red) User profile error Normal Normal, communicating successfully (green, lit). Not connected (green, flashing). RSB(+) 407 MNS (green Critical link failure (red, lit). No electricity RSA() 408 /red) Connection timeout (red, flashing) At poweron/communication SG 409 faulted (green/red, flashing)

11 Terminal Arrangement for 32A/MDL Single Loop Control Control output O (Suffix code: Type=0) Relay contact output Factory default: Control output is relay. NC 0 NO Contact rating: 250 V AC, 3 A 30 V DC, 3 A (resistance load) Heating/cooling control output Heating/cooling relay contact output (Suffix code: Type =2) Cooling O2 NO side 0 Heating O NO side Contact rating: 240 V AC, 3 A 30 V DC, 3 A (resistance load) (Equipped Contact output ALM as standard) External contact output (relay) Alarm3 output (PV high limit) Common Alarm2 output (PV low limit) Common Alarm output (PV high limit) Common 04 AL AL AL 09 Relay contact rating: 240 V AC, A 30 V DC, A (resistance load) Power supply V AC power supply 24 V AC/DC power supply N L 0 Allowable range: V AC (+0%/5%) (free voltage) 50/60 Hz shared N L (24 V AC/DC power supply: Optional suffix code /DC) Factory default: PV input type is undefined. PV input TC input Current (ma) input (Equipped PV as standard) RTD input A 20 b 202 B Voltage (mv, V) input Eterminal area Heater break alarm HBA (Optional suffix code /HA) External contact output (transistor) Heater current detection input Heater break alarm 30 HAL 307 output CT 3 Heater break alarm2 HAL2 308 output CT2 32 Common 309 Transistor contact rating: 24 V DC, 50 ma Retransmission output RET (Equipped as standard) Retransmission output 5 V DC loop power supply Can be used for 5 V DC loop power supply when not used for Default: PV retransmission retransmission output ma DC or V DC 020 ma DC (Max. 2 ma DC) Load resistance 600 Ω or less Default: 420 ma DC Coolingside control output RET/O2 Current/voltage pulse output (Suffix code: Type =2) Can not be used for retransmission output or 5 V DC loop power suppy when current/voltage pulse 020 ma DC, 420 ma DC, output is used for control output. Voltage pulse (2 V) Can be used for retransmission output or 5 V DC 206 loop power suppy when control output is not used. Current output range can be changed. Control output O (Suffix code: Type=0 or 2) Current/voltage pulse output Retransmission output 5 V DC loop power supply Default: Undefined ma DC, ma DC, Voltage pulse (2 V) 208 Contact input DI (Equipped as standard) External contact input Novoltage Transistor contact contact STOP when DI2=ON 20 DI2 RUN when DI2=OFF AO when DI=ON 2 DI MAN when DI=OFF 22 Common 020 ma DC, 420 ma DC 208 Default: 420 ma DC V DC (Max. 2 ma DC) Contact rating: 2 V DC, 0 ma or more Function can be assigned to the terminals with no function. 208 Can be used for retransmission output or 5 V DC loop power suppy when current/voltage pulse output is not used for control output. Current output range can be changed. +5V DI V DI ETerminal Area communication RS485 (Suffix code: Type 2=) SDB(+) 30 SDA() 302 SG 303 RDB(+) 304 RDA() V DC loop power supply LPS24 24 V DC loop power supply V DC (Max. 30 ma DC) (Suffix code: Type 2=0 and 305 optional suffix code /LP) CCLink communication (with Modbus master) CCL FG: Flame ground 30 (Suffix code: Type 3=3) SLD: Shield 302 If the is located at the end of a segment for the CCLink communication wiring,terminating resistors are separately needed. These are to be prepared by users. (0 Ω: pc.) DB 0Ω DA DG: TX/RX signal ground 303 DB: RX/TX signal signal 304 DA: RX/TX signal + signal 305 Not used 306 communication/24 V DC loop power supply 24 V DC loop power supply RS485/LPS24 RSB(+) 30 (Suffix code: Type 2= and optional suffix code /LP) V DC RSA() 302 (Max. 30 ma DC) 306 SG 303 CHK(red) 307 (Lit: User profile error/adress error, Unlit: Normal) L ERR(red) 308 (Lit: Communication failure(crc error), Unlit: Normal) L RUN(green) 309 (Lit: Normal, Unlit: No carrier detected/communication timeout) RSB(+) 30 RSA() 3 SG 32

12 2 External Dimensions and Panel Cutout Dimensions 35A/MDL 37(.46) 20 (4.72) min. (required for inserting/removing the cable for LL50A) 94.6(3.72) 9.6(3.6) Minimum cable curvature: R40 (.57) Cable for LL50 60(2.36) 00(3.94) 4(4.49) DIN rail TH3575A Unit: mm(inch) 90 (3.54) min. (required for removing the instrument from the DIN rail) 96(3.78) 20(0.79) 00(3.94) 4.3(0.7) 4(0.6) Note: Trigonometry General tolerance = ±(JIS B tolerance class IT8)/2 32A/MDL 5(0.59) Cable for LL50 20 (4.72) min. (required for inserting/removing the cable for LL50A) 94.6(3.72) 9.6(3.6) Minimum cable curvature: R40 (.57) 60(2.36) 00(3.94) 4(4.49) DIN rail TH3575A Unit: mm(inch) 90 (3.54) min. (required for removing the instrument from the DIN rail) 48.2(.90) 20(0.79) 00(3.94) 4(0.6) 4.3(0.7) Note: Trigonometry General tolerance = ±(JIS B tolerance class IT8)/2 Construction, Mounting, and Wiring Construction: Panel mount type Material: Polycarbonate resin (Flame retardancy: UL94 V0) DIN rail mounting bracket material: Panel steel sheet Case color: Black (Light Charcoal gray) Weight: kg or less External dimensions (mm): 55A/MDL: 96 (width) x 4 (height) x 00 (depth) 52A/MDL: 48.2 (width) x 4 (height) x 00 (depth) Compatible DIN rails: TH357.5Fe, TH357.5Al, JIS C 282 Mounting position: Horizontal. Wiring: M3 screw terminal with square washer (signal wiring and power)

13 Model and Suffix Code 35A Model Type : Basic control Type 2: Functions Type 3: Open networks Suffix code Optional suffix code /MDL (Required) Description Digital Indicating Controller (Power supply: V AC) (provided with retransmission output or 5 V DC loop power supply, 2 DIs, and 3 DOs) (without the display parts and keys) 0 Standard type 2 Heating/cooling type 0 None 2 5 additional DIs, 5 additional DOs communication (Max.38.4 kbps, 2wire/4wire) 2 Ethernet communication (with serial gateway function) 3 CCLink communication (with Modbus master function) 4 PROFIBUSDP communication (with Modbus master function) 5 DeviceNet communication (with Modbus master function) Fixed code Temperature unit: deg C & deg F Case color Black (Light charcoal gray) Fixed code 00 Always "00" /MDL (Required) Mount on DIN rail (without the display parts and keys) (*) Optional suffix codes /LP 24 V DC loop power supply (*) /DC Power supply 24 V AC/DC /CT Coating (*2) /CV Terminal cover *: The /MDL option and /LP option can be specified in the combination of Type 2 code 0 and Type 3 code. *2: When the /CT option is specified, the 35A does not conform to the safety standards (UL and CSA) and CE marking (Products with /CT option are not intended for EEAmarket). Model 32A Suffix code Optional suffix code /MDL (Required) Description Digital Indicating Controller (Power supply: V AC) (provided with retransmission output or 5 V DC loop power supply, 2 DIs, and 3 DOs) (without the display parts and keys) Type : 0 Standard type Basic control 2 Heating/cooling type Type 2: 0 None Functions communication (Max kbps, 2wire/4wire) (*) Type 3: 0 None Open networks 3 CCLink communication (with Modbus master function) Fixed code Temperature unit: deg C & deg F Case color Black (Light charcoal gray) Fixed code 00 Always "00" /MDL (Required) (*2) (*3) Mount on DIN rail (without the display parts and keys) /LP 24 V DC loop power supply (*3) Optional suffix codes /HA Heater break alarm (*4) /DC Power supply 24 V AC/DC /CT Coating (*5) /CV Terminal cover *: When /LP option is specified, the communication of the type 2 code is 2wire system. *2: The /MDL option is specified, the model and suffix codes are follows: 32A0000/x/MDL 32A00300/x/MDL 32A2000/x/MDL *3: When /MDL option and /LP option is combined, 3 can not be specified for Type 3 code. *4: The /HA option can be specified only in the combination of Type2 code "" and Type 3 code 0. *5: When the /CT option is specified, the 32A does not conform to the safety standards (UL and CSA) and CE marking (Products with /CT option are not intended for EEAmarket). 3

14 4 Items to be specified when ordering Model and suffix codes, whether User s Manual and QIC required. Standard accessories Operation Guide Special Order Items Model code Suffix code Description LL50A 00 Parameter Setting Software X00 See the General Specifications (*) Resistance Module *: Necessary to input the current signal to the voltage input terminal. Name Terminal cover (for 35A) Terminal cover (for 32A) User s Manual (CD) Model AP00 AP002 AP003 User s Manual Product user s manuals can be downloaded or viewed at the following URL. To view the user s manual, you need to use Adobe Reader 7 or later by Adobe Systems. URL: Subject to change without notice.