NCP5504, NCV ma Dual Output Low Dropout Linear Regulator

Size: px

Start display at page:

Download "NCP5504, NCV ma Dual Output Low Dropout Linear Regulator"

Beverley Owens
5 years ago
Views:

25 ma Dual Output Low Dropout Linear Regulator The NCP554/NCV554 are dual output low dropout linear regulators with 2.% accuracy over the operating temperature range.

1 25 ma Dual Output Low Dropout Linear Regulator The NCP554/NCV554 are dual output low dropout linear regulators with 2.% accuracy over the operating temperature range. They feature a fixed output voltage of 3.3 V (contact factory for other fixed output voltage options) and an adjustable output that ranges from 1.25 V to 5. V. It is available in a 5 pin DPAK PbFree package. The NCP554/NCV554 employs an architecture that offers low noise without a bypass capacitor for the fixed output. This device along with a ripple rejection of 75 db and a dropout of ma, suits postregulation and power sensitive batteryoperated applications. Features One Fixed and One Adjustable Output Pin 25 ma Each Output Adjustable Output Voltage from 1.25 V to 5. V Low Dropout Voltage of 25 mv typical at 25 ma Low Quiescent Current of 37 A typical Ripple Rejection of 75 db Temperature Range of NCP C to +85 C Temperature Range of NCV554 4 C to +125 C Low Noise Without Bypass Capacitor; 9 Vrms Line Regulation < 15 mv Load Regulation; 1 < 15 mv, 2 < 1 mv Accuracy of 2% Overtemperature Range Thermal Protection and Current Limit Short Circuit Protection NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AECQ Qualified and PPAP Capable These are PbFree Devices A L Y WW G DPAK5 DT SUFFIX CASE 175AA MARKING DIAGRAM 554G ALYWW Pin 1. Adjust for GND 4. V in 5. 1 = Assembly Location = Wafer Lot = Year = Work Week = PbFree Package ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet. Typical Applications Audio Visual Equipment Battery Powered Consumer Products Instrumentation Computing and Networking Applications Automotive Electronics Semiconductor Components Industries, LLC, 213 April, 213 Rev. 4 1 Publication Order Number: NCP554/D

2 PIN FUNCTION DESCRIPTION Pin No. Pin Name Description 1 Adjust for 2 This pin is connected to the resistor divider on the output. For a 1.25 put, connect directly to the 2 pin. 2 2 Adjustable Regulated Output Voltage. 3 GND Power Supply Ground 4 V in Positive Power Supply Input Voltage. 5 1 Fixed Regulated Output Voltage. See selector guide for options. MAXIMUM RATINGS Rating Symbol Value Unit Input Voltage V in 18 V Operating Input Voltage for Power Considerations V in 9. V Output Pin Voltage.3 to V in +.3 V Adjust Pin Voltage V adj.3 to V in +.3 V Maximum Junction Temperature NCP554 NCV554 T J C Operating Ambient Temperature NCP554 NCV554 T A 25 C to +85 C 4 C to +125 C C Package Thermal Resistance Thermal Resistance, JunctiontoAir Thermal Resistance, JunctiontoCase R JA R JC 8 Storage Temperature Range T stg 55 to +15 C Electrostatic Discharge Sensitivity Human Body Model (HBM) Machine Model (MM) Charge Device Model (CDM) Latchup Performance (JESD78) Positive Negative ESD I Latchup Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. C/W V ma 2

3 NCP554 ELECTRICAL CHARACTERISTICS (V in = + 1. V, where is the larger of 1 or 2,, unless otherwise noted) Output Voltage NCP554 (T A = 25 C to 85 C), I O = 25 ma Characteristic Symbol Min Typ Max Unit Adjustable Pin Current I adj 5 na Line Regulation ( + 1. V < V in < 7. V), I O = 25 ma Reg line 5 15 mv 1 2 2% 2% Load Regulation (1. ma < I O < 25 ma) for 1 Reg load 1 Load Regulation (1. ma < I O < 25 ma) for 2 5 Dropout Voltage (I O = 25 ma) V DO 25 4 mv % +2% 15 1 V mv mv Ripple Rejection Ratio (I O = 25 ma) 12 Hz 1 khz RR 75 6 db Quiescent Current (I O1, I O2 = ma) I q A Fixed Output Noise Voltage (1 Hz khz = 3.3 V, I O = ma, C O = 1. F) V n 9 Vrms Ground Current (I O1, I O2 = 25 ma) I gnd 1 2 ma Thermal Shutdown (Guaranteed by design) T Jmax C Current Limit on 1 and 2 I lim ma NCV554 ELECTRICAL CHARACTERISTICS (V in = + 1. V, where is the larger of 1 or 2, 4 C T J 15 C, 4 C T A 125 C, unless otherwise noted) Output Voltage NCV554, I O = 25 ma Characteristic Symbol Min Typ Max Unit Adjustable Pin Current I adj 5 na Line Regulation ( + 1. V < V in < 7. V), I O = 25 ma Reg line 5 15 mv 1 2 2% 2% Load Regulation (1. ma < I O < 25 ma) for 1 Reg load 1 Load Regulation (1. ma < I O < 25 ma) for 2 5 Dropout Voltage (I O = 25 ma) V DO 25 4 mv % +2% 15 1 V mv mv Ripple Rejection Ratio (I O = 25 ma) 12 Hz 1 khz RR 75 6 db Quiescent Current (I O1, I O2 = ma) I q A Fixed Output Noise Voltage (1 Hz khz = 3.3 V, I O = ma, C O = 1. F) V n 9 Vrms Ground Current (I O1, I O2 = 25 ma) I gnd 1 2 ma Thermal Shutdown (Guaranteed by design) T Jmax C Current Limit on 1 and 2 I lim ma 3

4 NCP554/ NCV554 NCP554/ NCV554 Adj 2 GND V in Adj 2 GND V in V in 1 V in 1 C out2 C in C out1 2 C n R2 Cout2 C in C out1 2 R1 GND GND Figure 1. Application Schematic, Fixed Output Version. 1 = 3.3 V, 2 = 1.25 V Figure 2. Application Schematic, Adjustable Version. 1 = 3.3 V, 2 = 1.25 V to 5. V, Where 2 = 1.25 V * (1+R2/R1) NOTE: Please note that in order to maintain high accuracy on the adjustable output (2 ), use R1 values < 3 k in the resistor divider. The recommended capacitor type and values are as follows: C in (Tantalum or Aluminum Electrolytic) = 4.7 F to F C out1, C out2 = Low ESR, 1. F to 22 F C n = pf to 1. nf. 4

5 TYPICAL CHARACTERISTICS 1, OUTPUT VOLTAGE (V) V in = 4.3 V 2, OUTPUT VOLTAGE (V) V in = 4.3 V I out, OUTPUT CURRENT (ma) Figure 3. Output Voltage vs. Output Load Current for I out, OUTPUT CURRENT (ma) Figure 4. Output Voltage vs. Output Load Current for 2 V DO, DROPOUT VOLTAGE (mv) I O1 = 25 ma I GND, GROUND CURRENT (ma) I O1 = I O2 = 25 ma T J, JUNCTION TEMPERATURE ( C) Figure 5. Dropout Voltage vs. Temperature for T J, JUNCTION TEMPERATURE ( C) Figure 6. Ground Current vs. Temperature 5

6 TYPICAL CHARACTERISTICS I im, SHORT CIRCUIT LIMIT (A) T J, JUNCTION TEMPERATURE ( C) Figure 7. Short Circuit Current Limit vs. Temperature for 1 I lim, SHORT CIRCUIT LIMIT (ma) T J, JUNCTION TEMPERATURE ( C) Figure 8. Short Circuit Current Limit vs. Temperature for 2 RR, RIPPLE REJECTION (db) = 3.3 V C out = 1. F T J = 25 C F, FREQUENCY (khz) I O = 1 ma I O = 25 ma RR, RIPPLE REJECTION (db) = 1.25 V C out = 1. F T J = 25 C I O = 25 ma F, FREQUENCY (khz) I O = 1 ma Figure 9. Ripple Rejection vs. Frequency for 1 Figure 1. Ripple Rejection vs. Frequency for 2 6

7 TYPICAL CHARACTERISTICS 6 6 NOISE DENSITY (nvrms/ Hz) = 3.3 V I O = 1 ma NOISE DENSITY (nvrms/ Hz) = 3.3 V I O = 25 ma START: Hz STOP: khz Figure 11. Noise Density vs. Frequency START: Hz STOP: khz Figure 12. Noise Density vs. Frequency 3 25 NOISE DENSITY (nvrms/ Hz) = 1.25 V I O = 1 ma NOISE DENSITY (nvrms/ Hz) = 1.25 V I O = 25 ma START: Hz STOP: khz START: Hz STOP: khz Figure 13. Noise Density vs. Frequency Figure 14. Noise Density vs. Frequency 7

8 TYPICAL CHARACTERISTICS 5 mv/div I O ma/div I O ma/div I O ma/div 5 mv/div mv/div mv/div I O = 1 ma to 25 ma 1 = 3.3 V I O = 1. ma to 25 ma 1 = 3.3 V TIME ( S/Div) TIME ( S/Div) Figure 15. Load Transient Response for 1 Figure 16. Load Transient Response for 1 I O = 1 ma to 25 ma 2 = 1.25 V I O ma/div I O = 1. ma to 25 ma 2 = 1.25 V TIME ( S/Div) TIME ( S/Div) Figure 17. Load Transient Response for 2 Figure 18. Load Transient Response for 2 V in 1. V/Div V in 1. V/Div 5 mv/div V in = 1. V 1 = 3.3 V I O = 25 ma T r = T f = 1. s 5 mv/div V in = 1. V 2 = 1.25 V I O = 25 ma T r = T f = 1. s TIME (4 S/Div) TIME (4 S/Div) Figure 19. Line Transient Response for 1 Figure 2. Line Transient Response for 2 8

9 APPLICATION INFORMATION Introduction The NCP554/NCV554 are high performance dual output, 25 ma linear regulators suitable for post regulation and power sensitive batteryoperated applications. They feature 2.% accuracy over the operating temperature range. With one fixed output voltage at 3.3 V, and one adjustable output voltage ranging from 1.25 V to 5. V, the dropout voltage is 25 mv typical. Additional features, such as an architecture that allows for low noise on the fixed output without a bypass capacitor, provides for an attractive LDO solution for audio visual equipment, instrumentation, computing and networking applications, and automotive electronics. It is thermally robust and is offered in a 5 pin DPAK PbFree package. Capacitor Selection The recommended input capacitor types are tantalum and aluminum electrolytic ranging from 4.7 F to F. It is especially required if the power source is located more than a few inches from the NCP554/NCV554. This capacitor will reduce device sensitivity and enhance the output transient response time. The PCB layout is very important and in order to obtain the optimal solution, the V in and GND traces should be sufficiently wide to minimize noise and unstable operation. For the adjustable output pin, C n ranges from pf and 1. nf. The output capacitor range is between 1. F and 22 F. For PCB layout considerations, place the capacitor close to the output pin and keep the leads short. Adjustable Output Operation The application circuit for the adjustable output version is shown in Figure 2. 2 is calculated based on the following equation: Vout V * 1 R2 R1 In order to maintain high accuracy on the adjustable output, R1 values should be < 3 k. ORDERING INFORMATION NCP554DTRKG NCV554DTRKG* Device Package Shipping DPAK (PbFree) DPAK (PbFree) 25 / Tape and Reel 25 / Tape and Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD811/D. *NCV Prefix for Automotive and Other Applications Requiring Unique Site and Control Change Requirements; AECQ Qualified and PPAP Capable 9

10 PACKAGE DIMENSIONS DPAK 5, CENTER LEAD CROP CASE 175AA ISSUE A V S F B R G L A K D 5 PL J H C.13 (.5) M T T SEATING PLANE E U R1 Z NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, CONTROLLING DIMENSION: INCH. INCHES MILLIMETERS DIM MIN MAX MIN MAX A B C D E F G.18 BSC 4.56 BSC H J K L.45 BSC 1.14 BSC R R S U.2.51 V Z SOLDERING FOOTPRINT* SCALE 4: mm inches *For additional information on our PbFree strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC s product/patent coverage may be accessed at SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 8217 USA Phone: or Toll Free USA/Canada Fax: or Toll Free USA/Canada orderlit@onsemi.com N. American Technical Support: Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: Japan Customer Focus Center Phone: ON Semiconductor Website: Order Literature: For additional information, please contact your local Sales Representative NCP554/D

NCP A, Low Dropout Linear Regulator with Enhanced ESD Protection

NCP A, Low Dropout Linear Regulator with Enhanced ESD Protection 3.0 A, Low Dropout Linear Regulator with Enhanced ESD Protection The NCP5667 is a high performance, low dropout linear regulator designed for high power applications that require up to 3.0 A current. A