ELEC 6740 LAB (Spring 2002) Circuit Schematic Diagram
|
|
- Lewis Bradford
- 5 years ago
- Views:
Transcription
1 ELEC 670 LAB (Spring 00) Circuit Schematic Diagram R(06) R(06) C(06) 8 LED R(06) VDD R(06) LED Switch Note: ) Four batteries are needed. ) 555 timer s pins are NOT in actual sequence. ) Board size should be limited in a in in square.
2 LMC555 CMOS Timer General Description The LMC555 is a CMOS version of the industry standard 555 series general purpose timers. In addition to the standard package (SOIC, MSOP, and MDIP) the LMC555 is also available in a chip sized package (8 Bump micro SMD) using National s micro SMD package technology. The LMC555 offers the same capability of generating accurate time delays and frequencies as the LM555 but with much lower power dissipation and supply current spikes. When operated as a one-shot, the time delay is precisely controlled by a single external resistor and capacitor. In the stable mode the oscillation frequency and duty cycle are accurately set by two external resistors and one capacitor. The use of National Semiconductor s LMCMOS process extends both the frequency range and low supply capability. Block and Connection Diagrams August 000 Features n Less than mw typical power dissipation at 5V supply n MHz astable frequency capability n.5v supply operating voltage guaranteed n Output fully compatible with TTL and CMOS logic at 5V supply n Tested to 0 ma, +50 ma output current levels n Reduced supply current spikes during output transitions n Extremely low reset, trigger, and threshold currents n Excellent temperature stability n Pin-for-pin compatible with 555 series of timers n Available in 8 pin MSOP Package and 8-Bump micro SMD package LMC555 CMOS Timer 8-Pin SOIC, MSOP, and MDIP Packages 8-Bump micro SMD Top View Pulse Width Modulator DS Top View (bump side down) DS DS DS LMCMOS is a trademark of National Semiconductor Corp. 000 National Semiconductor Corporation DS
3 Absolute Maximum Ratings (Notes, ) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage, V + 5V Input Voltages, V TRIG,V RES,V CTRL, V THRESH 0.V to V S + 0.V Output Voltages, V O,V DIS 5V Output Current I O,I DIS 00 ma Storage Temperature Range 65 C to +50 C Soldering Information MDIP Soldering (0 seconds) 60 C SOIC, MSOP Vapor Phase (60 sec) 5 C SOIC, MSOP Infrared (5 sec) 0 C Note: See AN-50 Surface Mounting Methods and Their Effect on Product Reliability for other methods of soldering surface mount devices. Operating Ratings(Notes, ) Termperature Range 0 C to +85 C Thermal Resistance (θ JA ) (Note ) SO, 8-lead Small Outline 69 C/W MSOP, 8-lead Mini Small Outline 5 C/W MDIP, 8-lead Molded Dip C/W 8-Bump micro SMD 0 C/W Maximum Allowable Power C MDIP-8 6mW SO-8 70mW MSOP-8 555mW 8 Bump micro SMD 568mW Electrical Characteristics (Notes, ) Test Circuit, T = 5 C, all switches open, RESET to V S unless otherwise noted Symbol Parameter Conditions Min Typ Max Units (Limits) I S Supply Current V S =.5V V S =5V V S = V V CTRL Control Voltage V S =.5V V S =5V V S = V V DIS Discharge Saturation Voltage V S =.5V, I DIS =ma V S = 5V, I DIS =0mA V OL Output Voltage (Low) V S =.5V, I O =ma V S = 5V, I O =8mA V S = V, I O =50mA V OH Output Voltage (High) V TRIG Trigger Voltage V S =.5V V S = V V S =.5V, I O = 0.5 ma V S = 5V, I O = ma V S = V, I O = 0 ma I TRIG Trigger Current V S =5V 0 pa V RES Reset Voltage V S =.5V (Note ) V S = V I RES Reset Current V S =5V 0 pa I THRESH Threshold Current V S =5V 0 pa I DIS Discharge Leakage V S = V.0 00 na t Timing Accuracy SW, Closed V S =.5V V S =5V V S = V t/ V S Timing Shift with Supply V S =5V±V 0. %/V t/ T Timing Shift with V S =5V 75 ppm/ C Temperature 0 C T +85 C f A Astable Frequency SW, Closed, V S = V khz f MAX Maximum Frequency Max. Freq. Test Circuit, V S = 5V.0 MHz t R,t F Output Rise and Fall Times Max. Freq. Test Circuit V S = 5V, C L =0pF µa V mv V V V V ms 5 ns
4 Physical Dimensions inches (millimeters) unless otherwise noted Molded Small Outline (SO) Package (M) NS Package Number M08A 8-Lead (0.8 Wide) Molded Mini Small Outline Package NS Package Number MUA08A 8
5 SUBMINIATURE SOLID STATE LAMPS AMID08 AMSGD08 AMYD08 AMEC08 AMSGC08 AMYC08 Features SUBMINIATURE PACKAGE. WIDE VIEWING ANGLE. YOKE LEAD. LONG LIFE SOLID STATE RELIABILITY. LOW PACKAGE PROFILE. Description The High Efficiency Red source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Orange Light Emitting Diode. The Super Bright Green source color devices are made with Gallium Phosphide Green Light Emitting Diode. The Yellow source color devices are made with Gallium Arsenide Phosphide on Gallium Phosphide Yellow Light Emitting Diode. Package Dimensions Notes:. All dimensions are in millimeters (inches).. Tolerance is ±0.5(0.0") unless otherwise noted.. Lead spacing is measured where the lead emerge package.. Specifications are subjected to change without notice. AMxxx08-
6 AMxxx08 SERIES SMT Reflow Soldering Instructions AMxxx08 SERIES Recommended Soldering Pattern (Units : mm) AMxxx08-5
7 R Series SS PCB Mount Ultra-Miniature Slide Switches TYPICAL SWITCH ORDERING EXAMPLE SS S D P MOUNTING No Code Through-Hole SMD POLES & CIRCUITS SPDT ON NONE ON SPT ON ON ON DPDT ON NONE ON (Illuminated w/-on not available; SMD with single pole only) TERMINAL SPACING For Through-Hole B Metric.0mm X.0mm D Inch.00" X.00" (Illuminated available with inch spacing only) For SMD A Metric.0mm X.0mm ACTUATION For Through-Hole P Top Actuated H Side Actuated For SMD H Side Actuated LED CIRCUIT L Isolated LED COLORS C Red E Yellow F Green CONTACT MATERIALS Silver over Brass Gold over Brass Gold standard for SMD SMD PACKAGING Tape-Reel R 500 Pieces/Reel No Partitioned Tray Code * S CONTACTS Shorting See note below for SPT. DESCRIPTION FOR TYPICAL ORDERING EXAMPLE SSSDP Top Actuated SPDT ON-NONE-ON Circuit Silver Contacts Shorting Contacts Terminals with.00" Spacing Pole Model POLES & CIRCUITS Slide Position Connected Terminals Throw & Schematics Right Center Left Right Center Left Note: Terminal numbers not actually on switch. Isolated LED circuit requires external power source. SS SP ON NONE ON - OPEN - SS SPDT (COM) L (+) (-) L SS SP ON ON ON SS SPT (COM) Note: ON-OFF-ON circuit can be created by not connecting terminal. * Shorting between terminals &. Nonshorting between terminals &. DP SS ON NONE ON - 5- OPEN (COM) 5 DPDT L (+) L (-) 6 General Specifications Dimensions Dimensions Dimensions illuminated NKK Switches sales@nkkswitches.com Phone (80) Fax (80)
8 R Series SS PCB Mount Ultra-Miniature Slide Switches SHORTING CONTACTS S Shorting (Make-before-break) See explanation on the Engineering Particulars page. TERMINAL SPACING For Through-Hole B Metric.0mm with Black Base (.). (0.) (6.0).6 (.0) (0.0).9 (.) (.0) (.) On-None-On Single Pole Models On-None-On Double Pole Models -on Models D Inch.00" with Gray Base.06 (.5) Typ (0.).0 (.). (.5) Typ (.5) Typ.00.0 (6.5).57 (.5).00 (0.).0 (.). 5 6 (.5) Typ.00.0 (.5).00 (5.08).00 (.5) Typ (.). (5.08).00 (.5) Typ.00.0 On-None-On Single Pole Models On-None-On Double Pole Models Illuminated Models -on Models For SMD A.57 Metric.0mm with Black Base (9.).6 (.).055 (0.7) Typ On-None-On Single Pole Models (.7).067 (9.8).86 (5.6).0 (.55).00 (.0) Typ.09 (.7) Typ.067 (.).65 (.5).9 (.).055 (0.7) Typ On Single Pole Models (.7).067 (.).56 (5.6).0 (.55).00 5 (.0) Typ.09 (.7) Typ.067 ACTUATION P Top (.) (.0) Actuated H Side.07 Actuated (.5).059 (.5) Through-Hole Through-Hole.059 SMD (.5).098 (.).07 (.0) (.).09 (.5).059 NKK Switches sales@nkkswitches.com Phone (80) Fax (80)
9 Surface Mount PCB Lithium Coin Cell Battery Retainers Surface Mount PCB Lithium Coin Cell Battery Retainers Click to Request Samples CAT. NO. (BULK) A B C D F H DIA. CELL SIZE TAPE & REEL SPEC'S* CAT. NO. (ON TAPE) mm Wide; mm Pitch; x.00.0 RAD. 6.8mm " Reel 998TR (50 per Reel) mm Wide; 6mm Pitch; mm " Reel 000TR (000 per Reel) mm Wide; mm Pitch; mm " Reel 00TR (500 per Reel) 56mm Wide; mm Pitch; " Reel 00TR (00 per Reel) mm 56mm Wide; mm Pitch; 00TR mm " Reel (00 per Reel) 006TR 56mm Wide; mm Pitch; " Reel 008TR (00 per Reel) Material:.00" Phosphor Bronze Finish: Nickel Plate * All conductive polystyrene carrier tape meets ANSI/EIA - 8 standard. ( of ) [/9/00 9:6: PM]
10 Surface Mount PCB Lithium Coin Cell Battery Retainers BATTERY REFERENCE CAT. NO. Duracell, Eveready, Panasonic, Sony, Toshiba, Varta, Ray-O-Vac, Sanyo, Seiko CELL SIZE 998 MC6, V6, SC6 6.8mm 000 BR6, CR6, BR0, CL0, CR0, BR5 mm 00 BR06, CR06, DL06, BR00, CL00, BR05, CR05, DL05, DR0, CR0, DL0 0mm 00 CR5, DL BR0, CL0, CR0, BR5, CR5, DL5, BR0, CL0 mm 006 CR0, DL0 mm 008 CR50, DL50 50 Home Page Standard Products Go Back Keystone Electronics Corp th Road Astoria, NY 05 USA Phone: (78) Toll Free: (800) -550 Fax: (78) ( of ) [/9/00 9:6: PM]
LMC555 CMOS Timer. Features. Block and Connection Diagrams. Pulse Width Modulator. October 2003
LMC555 CMOS Timer General Description The LMC555 is a CMOS version of the industry standard 555 series general purpose timers. In addition to the standard package (SOIC, MSOP, and MDIP) the LMC555 is also
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LMC555 CMOS Timer General Description The LMC555 is a CMOS version of the
More informationLMC555 CMOS LMC CMOS. 8-Pin SOIC, MSOP, and MDIP Packages. 8-Bump micro SMD. Top View (Bump side down) ds LMC555 CMOS LMC555. 3MHz 1.
CMOS 555 CMOS (SOIC MSOP MDIP) micro SMD (8 micro SMD) LM555 2 1 LMCMOS TM CMOS 19850925 24100 ds008669 5V 1mW 3MHz 1.5V Converted to nat2000 DTD added title to the 2 avos on the first page Edited for
More informationFeatures. Applications
LM555 Timer General Description The LM555 is a highly stable device for generating accurate time delays or oscillation. Additional terminals are provided for triggering or resetting if desired. In the
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM555 Timer General Description The LM555 is a highly stable device for
More informationLM386 - Low Voltage Audio Power Amplifier
LM386 - Low Voltage Audio Power Amplifier Features Typical Application Battery operation Minimum external parts Wide supply voltage range: 4V-12V or 5V-18V Low quiescent current drain: 4mA Voltage gains
More informationLM158/LM258/LM358/LM2904 Low Power Dual Operational Amplifiers
LM158/LM258/LM358/LM2904 Low Power Dual Operational Amplifiers General Description The LM158 series consists of two independent, high gain, internally frequency compensated operational amplifiers which
More informationNE556 SA556 - SE556 GENERAL PURPOSE DUAL BIPOLAR TIMERS
NE556 SA556 - SE556 GENERAL PURPOSE DUAL BIPOLAR TIMERS LOW TURN OFF TIME MAXIMUM OPERATING FREQUENCY GREATER THAN 500kHz TIMING FROM MICROSECONDS TO HOURS OPERATES IN BOTH ASTABLE AND MONOSTABLE MODES
More informationLM386 Low Voltage Audio Power Amplifier
LM386 Low Voltage Audio Power Amplifier General Description The LM386 is a power amplifier designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part
More informationLM231A/LM231/LM331A/LM331 Precision Voltage-to-Frequency Converters
LM231A/LM231/LM331A/LM331 Precision Voltage-to-Frequency Converters General Description The LM231/LM331 family of voltage-to-frequency converters are ideally suited for use in simple low-cost circuits
More informationApplications. NS Part Number SMD Part Number NS Package Number Package Description LM555H/883 H08A 8LD Metal Can LM555J/883 J08A 8LD Ceramic Dip
LM555QML Timer General Description The LM555 is a highly stable device for generating accurate time delays or oscillation. Additional terminals are provided for triggering or resetting if desired. In the
More informationLM79XX Series 3-Terminal Negative Regulators
3-Terminal Negative Regulators General Description The LM79XX series of 3-terminal regulators is available with fixed output voltages of 5V, 12V, and 15V. These devices need only one external component
More informationLM386 Low Voltage Audio Power Amplifier
Low Voltage Audio Power Amplifier General Description The is a power amplifier designed for use in low voltage consumer applications. The gain is internally set to 20 to keep external part count low, but
More informationLMV761/LMV762 Low Voltage, Precision Comparator with Push-Pull Output
LMV761/LMV762 Low Voltage, Precision Comparator with Push-Pull Output General Description The LMV761/762 are precision comparators intended for applications requiring low noise and low input offset voltage.
More informationcss Custom Silicon Solutions, Inc.
css Custom Silicon Solutions, Inc. GENERAL PART DESCRIPTION The is a micropower version of the popular timer IC. It features an operating current under µa and a minimum supply voltage of., making it ideal
More informationLMV331 Single / LMV393 Dual / LMV339 Quad General Purpose, Low Voltage, Tiny Pack Comparators
General Purpose, Low Voltage, Tiny Pack Comparators General Description The LMV393 and LMV339 are low voltage (2.7-5V) versions of the dual and quad comparators, LM393/339, which are specified at 5-30V.
More informationLM392/LM2924 Low Power Operational Amplifier/Voltage Comparator
LM392/LM2924 Low Power Operational Amplifier/Voltage Comparator General Description The LM392 series consists of 2 independent building block circuits. One is a high gain, internally frequency compensated
More informationLM567/LM567C Tone Decoder
LM567/LM567C Tone Decoder General Description The LM567 and LM567C are general purpose tone decoders designed to provide a saturated transistor switch to ground when an input signal is present within the
More informationCD4047BC Low Power Monostable/Astable Multivibrator
Low Power Monostable/Astable Multivibrator General Description The CD4047B is capable of operating in either the monostable or astable mode. It requires an external capacitor (between pins 1 and 3) and
More informationLMC7215/LMC7225 Micro-Power, Rail-to-Rail CMOS Comparators with Push-Pull/Open-Drain Outputs and TinyPak Package
Micro-Power, Rail-to-Rail CMOS Comparators with Push-Pull/Open-Drain Outputs and TinyPak Package General Description The are ultra low power comparators with a maximum of 1 µa power supply current. They
More informationLM160/LM360 High Speed Differential Comparator
High Speed Differential Comparator General Description The is a very high speed differential input, complementary TTL output voltage comparator with improved characteristics over the µa760/µa760c, for
More informationCD4541BC Programmable Timer
CD4541BC Programmable Timer General Description The CD4541BC Programmable Timer is designed with a 16-stage binary counter, an integrated oscillator for use with an external capacitor and two resistors,
More informationLM2596 SIMPLE SWITCHER Power Converter 150 khz 3A Step-Down Voltage Regulator
LM2596 SIMPLE SWITCHER Power Converter 150 khz 3A Step-Down Voltage Regulator General Description The LM2596 series of regulators are monolithic integrated circuits that provide all the active functions
More informationADC Bit µp Compatible A/D Converter
ADC1001 10-Bit µp Compatible A/D Converter General Description The ADC1001 is a CMOS, 10-bit successive approximation A/D converter. The 20-pin ADC1001 is pin compatible with the ADC0801 8-bit A/D family.
More informationLMC6762 Dual MicroPower Rail-To-Rail Input CMOS Comparator with Push-Pull Output
LMC6762 Dual MicroPower Rail-To-Rail Input CMOS Comparator with Push-Pull Output General Description The LMC6762 is an ultra low power dual comparator with a maximum supply current of 10 µa/comparator.
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM231A/LM231/LM331A/LM331 Precision Voltage-to-Frequency Converters General
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM392 Low Power Operational Amplifier/Voltage Comparator General Description
More informationPIN CONFIGURATION FEATURES APPLICATIONS BLOCK DIAGRAM. D, F, N Packages
DESCRIPTION Both the and - Dual Monolithic timing circuits are highly stable controllers capable of producing accurate time delays or oscillation. The and - are a dual. Timing is provided by an external
More informationLM2679 SIMPLE SWITCHER 5A Step-Down Voltage Regulator with Adjustable Current Limit
SIMPLE SWITCHER 5A Step-Down Voltage Regulator with Adjustable Current Limit General Description The LM2679 series of regulators are monolithic integrated circuits which provide all of the active functions
More informationLM1558/LM1458 Dual Operational Amplifier
LM1558/LM1458 Dual Operational Amplifier General Description The LM1558 and the LM1458 are general purpose dual operational amplifiers. The two amplifiers share a common bias network and power supply leads.
More informationLM193/LM293/LM393/LM2903 Low Power Low Offset Voltage Dual Comparators
Low Power Low Offset Voltage Dual Comparators General Description The LM193 series consists of two independent precision voltage comparators with an offset voltage specification as low as 2.0 mv max for
More informationLM158/LM258/LM358/LM2904 Low Power Dual Operational Amplifiers
Low Power Dual Operational Amplifiers General Description The LM158 series consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically
More informationUniversity of Southern California
University of Southern California Department of Electrical Engineering - Electrophysics EE 202L Linear Circuits Lab #7 This lab uses the 555 timer IC as an astable multivibrator, a circuit with a periodic
More informationLM2660/LM2661 Switched Capacitor Voltage Converter
LM2660/LM2661 Switched Capacitor Voltage Converter General Description The LM2660/LM2661 CMOS charge-pump voltage converter inverts a positive voltage in the range of 1.5V to 5.5V to the corresponding
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LMC567 Low Power Tone Decoder General Description The LMC567 is a low power
More informationLM2686 Regulated Switched Capacitor Voltage Converter
LM2686 Regulated Switched Capacitor Voltage Converter General Description The LM2686 CMOS charge-pump voltage converter operates as an input voltage doubler and a +5V regulator for an input voltage in
More informationLM311 - Voltage Comparator
LM3 - Voltage Comparator Features Typical Application Operates from single 5V supply Input current: 50 na max. over temperature Offset current: 20 na max. over temperature Differential input voltage range:
More informationUNISONIC TECHNOLOGIES CO., LTD USA555 Advance LINEAR INTEGRATED CIRCUIT
UNISONIC TECHNOLOGIES CO., LTD PRECISION TIMERS DESCRIPTION The UTC USA555 monolithic timing circuit is a highly stable controller capable of producing accurate time delays or oscillation. In the time-delay
More informationLM1458/LM1558 Dual Operational Amplifier
Dual Operational Amplifier General Description The LM1458 and the LM1558 are general purpose dual operational amplifiers. The two amplifiers share a common bias network and power supply leads. Otherwise,
More informationLMC660 CMOS Quad Operational Amplifier
CMOS Quad Operational Amplifier General Description The LMC660 CMOS Quad operational amplifier is ideal for operation from a single supply. It operates from +5V to +15.5V and features rail-to-rail output
More informationLM2931 Series Low Dropout Regulators
LM2931 Series Low Dropout Regulators General Description The LM2931 positive voltage regulator features a very low quiescent current of 1mA or less when supplying 10mA loads. This unique characteristic
More informationLM161/LM261/LM361 High Speed Differential Comparators
LM161/LM261/LM361 High Speed Differential Comparators General Description The LM161/LM261/LM361 is a very high speed differential input, complementary TTL output voltage comparator with improved characteristics
More informationLMC567 Low Power Tone Decoder
Low Power Tone Decoder General Description The LMC567 is a low power general purpose LMCMOS tone decoder which is functionally similar to the industry standard LM567. It consists of a twice frequency voltagecontrolled
More informationLM193/LM293/LM393/LM2903 Low Power Low Offset Voltage Dual Comparators
LM193/LM293/LM393/LM2903 Low Power Low Offset Voltage Dual Comparators General Description The LM193 series consists of two independent precision voltage comparators with an offset voltage specification
More informationLM2240 Programmable Timer Counter
LM2240 Programmable Timer Counter General Description The LM2240 Programmable Timer Counter is a monolithic controller capable of both monostable and astable operation Monostable operation allows accurate
More informationLM2685 Dual Output Regulated Switched Capacitor Voltage Converter
Dual Output Regulated Switched Capacitor Voltage Converter General Description The LM2685 CMOS charge-pump voltage converter operates as an input voltage doubler, +5V regulator and inverter for an input
More informationDistributed by: www.jameco.com -800-8- The content and copyrights of the attached material are the property of its owner. NE SA - SE GENERAL PURPOSE SINGLE BIPOLAR TIMERS LOW TURN OFF TIME MAXIMUM OPERATING
More informationCA555, CA555C, LM555, LM555C, NE555
May 99 SEMICONDUCTOR CA, CAC, LM, LMC, NE Timers for Timing Delays and Oscillator Application in Commercial, Industrial and Military Equipment Features Accurate Timing From Microseconds Through Hours Astable
More informationLM2682 Switched Capacitor Voltage Doubling Inverter
Switched Capacitor Voltage Doubling Inverter General Description The LM2682 is a CMOS charge-pump voltage inverter capable of converting positive voltage in the range of +2.0V to +5.5V to the corresponding
More information. HIGH MAXIMUM ASTABLE FREQUENCY 2.7MHz PIN-TO-PIN AND FUNCTIONALLY COMPATIBLE WITH BIPOLAR NE555
TS555C,I,M LOW POWER SINGLE CMOS TIMERS. ERY LOW POWER CONSUMPTION : 100µA typ at CC = 5. HIGH MAXIMUM ASTABLE FREQUENCY 2.7MHz PIN-TO-PIN AND FUNCTIONALLY COMPATIBLE WITH BIPOLAR NE555. OLTAGE RANGE :
More informationLMS485 5V Low Power RS-485 / RS-422 Differential Bus Transceiver
5V Low Power RS-485 / RS-422 Differential Bus Transceiver General Description The LMS485 is a low power differential bus/line transceiver designed for high speed bidirectional data communication on multipoint
More informationLMC6572 Dual/LMC6574 Quad Low Voltage (2.7V and 3V) Operational Amplifier
LMC6572 Dual/LMC6574 Quad Low Voltage (2.7V and 3V) Operational Amplifier General Description Low voltage operation and low power dissipation make the LMC6574/2 ideal for battery-powered systems. 3V amplifier
More informationLM6172 Dual High Speed, Low Power, Low Distortion, Voltage Feedback Amplifiers
LM6172 Dual High Speed, Low Power, Low Distortion, Voltage Feedback Amplifiers General Description The LM6172 is a dual high speed voltage feedback amplifier. It is unity-gain stable and provides excellent
More informationLM111/LM211/LM311 Voltage Comparator
LM111/LM211/LM311 Voltage Comparator 1.0 General Description The LM111, LM211 and LM311 are voltage comparators that have input currents nearly a thousand times lower than devices like the LM106 or LM710.
More informationLMS75LBC176 Differential Bus Transceivers
LMS75LBC176 Differential Bus Transceivers General Description The LMS75LBC176 is a differential bus/line transceiver designed for bidirectional data communication on multipoint bus transmission lines.
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM317L 3-Terminal Adjustable Regulator General Description The LM317L is
More informationLM833 Dual Audio Operational Amplifier
LM833 Dual Audio Operational Amplifier General Description The LM833 is a dual general purpose operational amplifier designed with particular emphasis on performance in audio systems. This dual amplifier
More informationCD4069, CD4069-SMD Inverter Circuits
CD4069, CD4069-SMD Inverter Circuits General Description The CD4069UB consists of six inverter circuits and is manufactured using complementary MOS (CMOS) to achieve wide power supply operating range,
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. LM138/LM338 5-Amp Adjustable Regulators General Description The LM138 series
More informationZSCT1555 PRECISION SINGLE CELL TIMER ISSUE 2 - MAY 1998 DEVICE DESCRIPTION FEATURES APPLICATIONS SCHEMATIC DIAGRAM
PRECISION SINGLE CELL TIMER ZSCT555 ISSUE 2 - MAY 998 DEVICE DESCRIPTION These devices are precision timing circuits for generation of accurate time delays or oscillation. Advanced circuit design means
More informationDS75451/2/3 Series Dual Peripheral Drivers
DS75451/2/3 Series Dual Peripheral Drivers General Description The DS7545X series of dual peripheral drivers is a family of versatile devices designed for use in systems that use TTL logic. Typical applications
More informationLM2664 Switched Capacitor Voltage Converter
Switched Capacitor Voltage Converter General Description The LM2664 CMOS charge-pump voltage converter inverts a positive voltage in the range of +1.8V to +5.5V to the corresponding negative voltage of
More informationQuad SPST JFET Analog Switch SW06
a FEATURES Two Normally Open and Two Normally Closed SPST Switches with Disable Switches Can Be Easily Configured as a Dual SPDT or a DPDT Highly Resistant to Static Discharge Destruction Higher Resistance
More informationLM431 Adjustable Precision Zener Shunt Regulator
Adjustable Precision Zener Shunt Regulator General Description The LM431 is a 3-terminal adjustable shunt regulator with guaranteed temperature stability over the entire temperature range of operation.
More informationDS3662 Quad High Speed Trapezoidal Bus Transceiver
DS3662 Quad High Speed Trapezoidal Bus Transceiver General Description The DS3662 is a quad high speed Schottky bus transceiver intended for use with terminated 120Ω impedance lines. It is specifically
More informationLM124/LM224/LM324/LM2902 Low Power Quad Operational Amplifiers
Low Power Quad Operational Amplifiers General Description The LM124 series consists of four independent, high gain, internally frequency compensated operational amplifiers which were designed specifically
More informationHigh-Efficiency, 40V White LED Driver with Dimming Control
High-Efficiency, 40V White LED Driver with Dimming Control Description The is a step-up DC/DC converter specifically designed for driving WLEDs with a constant current. The can drive up 10 white LEDs in
More informationLM556 Dual Timer. an external resistor and capacitor for each timing Adjustable Duty Cycle
1 LM556 Dual Timer LM556 SNAS549A MARCH 2000 REVISED OCTOBER 2015 1 Features 3 Description 1 Direct Replacement for SE556/NE556 The LM556 dual-timing circuit is a highly-stable controller capable of producing
More informationLM337L 3-Terminal Adjustable Regulator
LM337L 3-Terminal Adjustable Regulator General Description The LM337L is an adjustable 3-terminal negative voltage regulator capable of supplying 100mA over a 1.2V to 37V output range. It is exceptionally
More informationLF442 Dual Low Power JFET Input Operational Amplifier
LF442 Dual Low Power JFET Input Operational Amplifier General Description The LF442 dual low power operational amplifiers provide many of the same AC characteristics as the industry standard LM1458 while
More informationData Sheet. HSDL-44xx IR Emitter Series HSDL-54xx IR Detector Series High-Performance IR Emitter and IR PIN Photodiode in Subminiature SMT Package
HSDL-44xx IR Emitter Series HSDL-54xx IR Detector Series High-Performance IR Emitter and IR PIN Photodiode in Subminiature SMT Package Data Sheet Description Flat Top Package The HSDL-44 Series of flat
More informationLM , -8.2, -8.4, -12.6, Lithium-Ion Battery Charge Controller
LM3420-4.2, -8.2, -8.4, -12.6, -16.8 Lithium-Ion Battery Charge Controller General Description The LM3420 series of controllers are monolithic integrated circuits designed for charging and end-of-charge
More informationMADR TR. Quad Driver for GaAs FET or PIN Diode Switches and Attenuators Rev. 4. Functional Schematic. Features.
Features High Voltage CMOS Technology Four Channel Positive Voltage Control CMOS device using TTL input levels Low Power Dissipation Low Cost Lead-Free SOIC-16 Plastic Package Halogen-Free Green Mold Compound
More informationLM118/LM218/LM318 Operational Amplifiers
LM118/LM218/LM318 Operational Amplifiers General Description The LM118 series are precision high speed operational amplifiers designed for applications requiring wide bandwidth and high slew rate. They
More informationLM2662/LM2663 Switched Capacitor Voltage Converter
LM2662/LM2663 Switched Capacitor Voltage Converter General Description The LM2662/LM2663 CMOS charge-pump voltage converter inverts a positive voltage in the range of 1.5V to 5.5V to the corresponding
More informationDS7830/DS8830 Dual Differential Line Driver
DS7830/DS8830 Dual Differential Line Driver General Description The DS7830/DS8830 is a dual differential line driver that also performs the dual four-input NAND or dual four-input AND function. TTL (Transistor-Transistor-Logic)
More informationMM74HCU04 Hex Inverter
MM74HCU04 Hex Inverter General Description The MM74HCU04 inverters utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard
More informationLM4250 Programmable Operational Amplifier
LM4250 Programmable Operational Amplifier General Description The LM4250 and LM4250C are extremely versatile programmable monolithic operational amplifiers. A single external master bias current setting
More informationLP2967 Dual Micropower 150 ma Low-Dropout Regulator in micro SMD Package
Dual Micropower 150 ma Low-Dropout Regulator in micro SMD Package General Description The LP2967 is a 150 ma, dual fixed-output voltage regulator designed to provide ultra low-dropout and low noise in
More informationLMV301 Low Input Bias Current, 1.8V Op Amp w/ Rail-to-Rail Output
Low Input Bias Current, 1.8V Op Amp w/ Rail-to-Rail Output General Description The LMV301 CMOS operational amplifier is ideal for single supply, low voltage operation with a guaranteed operating voltage
More informationADC0808/ADC Bit µp Compatible A/D Converters with 8-Channel Multiplexer
ADC0808/ADC0809 8-Bit µp Compatible A/D Converters with 8-Channel Multiplexer General Description The ADC0808, ADC0809 data acquisition component is a monolithic CMOS device with an 8-bit analog-to-digital
More informationLM2907/LM2917 Frequency to Voltage Converter
LM2907/LM2917 Frequency to Voltage Converter General Description The LM2907, LM2917 series are monolithic frequency to voltage converters with a high gain op amp/comparator designed to operate a relay,
More informationLM148/LM248/LM348 Quad 741 Op Amps
Quad 741 Op Amps General Description The LM148 series is a true quad 741. It consists of four independent, high gain, internally compensated, low power operational amplifiers which have been designed to
More informationDS26C31T/DS26C31M CMOS Quad TRI-STATE Differential Line Driver
DS26C31T/DS26C31M CMOS Quad TRI-STATE Differential Line Driver General Description The DS26C31 is a quad differential line driver designed for digital data transmission over balanced lines. The DS26C31T
More informationLM6118/LM6218 Fast Settling Dual Operational Amplifiers
Fast Settling Dual Operational Amplifiers General Description The LM6118/LM6218 are monolithic fast-settling unity-gain-compensated dual operational amplifiers with ±20 ma output drive capability. The
More informationLM431 Adjustable Precision Zener Shunt Regulator
Adjustable Precision Zener Shunt Regulator General Description The LM431 is a 3-terminal adjustable shunt regulator with guaranteed temperature stability over the entire temperature range of operation.
More informationPI5A4684. Chip Scale Packaging, Dual SPDT Analog Switch. Features. Description. Pin Configuration/ Block Diagram (top view) CSP.
Features CMOS Technology for Bus and Analog Applications Low On-Resistance: 0.5Ω. Wide Range: 1.65V to 5.5V Rail-to-Rail Signal Range Control Input Overvoltage Tolerance: 5.5V min. High Off Isolation:
More informationMM5452/MM5453 Liquid Crystal Display Drivers
MM5452/MM5453 Liquid Crystal Display Drivers General Description The MM5452 is a monolithic integrated circuit utilizing CMOS metal gate, low threshold enhancement mode devices. It is available in a 40-pin
More informationCD4069UBC Inverter Circuits
CD4069UBC Inverter Circuits General Description The CD4069UB consists of six inverter circuits and is manufactured using complementary MOS (CMOS) to achieve wide power supply operating range, low power
More informationLM185/LM285/LM385 Adjustable Micropower Voltage References
LM185/LM285/LM385 Adjustable Micropower Voltage References General Description The LM185/LM285/LM385 are micropower 3-terminal adjustable band-gap voltage reference diodes. Operating from 1.24 to 5.3V
More informationDS3486 Quad RS-422, RS-423 Line Receiver
DS3486 Quad RS-422, RS-423 Line Receiver General Description National s quad RS-422, RS-423 receiver features four independent receivers which comply with EIA Standards for the electrical characteristics
More informationLF353 Wide Bandwidth Dual JFET Input Operational Amplifier
LF353 Wide Bandwidth Dual JFET Input Operational Amplifier General Description These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage
More informationCD4538 Dual Precision Monostable
CD4538 Dual Precision Monostable General Description The CD4538BC is a dual, precision monostable multivibrator with independent trigger and reset controls. The device is retriggerable and resettable,
More informationDM74ALS520 DM74ALS521 8-Bit Comparator
8-Bit Comparator General Description These comparators perform an equal to comparison of two 8-bit words with provision for expansion or external enabling. The matching of the two 8-bit input plus a logic
More informationLM1815 Adaptive Variable Reluctance Sensor Amplifier
February 1995 LM1815 Adaptive Variable Reluctance Sensor Amplifier General Description The LM1815 is an adaptive sense amplifier and default gating circuit for motor control applications The sense amplifier
More informationNC7SZ175 TinyLogic UHS D-Type Flip-Flop with Asynchronous Clear
TinyLogic UHS D-Type Flip-Flop with Asynchronous Clear General Description The NC7SZ175 is a single positive edge-triggered D-type CMOS Flip-Flop with Asynchronous Clear from Fairchild s Ultra High Speed
More informationFST Bit Low Power Bus Switch
2-Bit Low Power Bus Switch General Description The FST3306 is a 2-bit ultra high-speed CMOS FET bus switch with TTL-compatible active LOW control inputs. The low on resistance of the switch allows inputs
More informationCD4538BC Dual Precision Monostable
CD4538BC Dual Precision Monostable General Description The CD4538BC is a dual, precision monostable multivibrator with independent trigger and reset controls. The device is retriggerable and resettable,
More informationJC6353V2.02. Description. Features. Application. Typical Application Circuits. 450mA ULTRA LOW DROPOUT POSITIVE VOLTAGE REGULATOR
Description JC6353 series is a group of positive voltage output, three-pin regulators, that provide a high current even when the input/output voltage differential is small. Low power consumption and high
More informationLTV-063L LVTTL/LVCMOS Compatible 3.3V Dual-Channel Optocouplers (10 Mb/s)
LTV-063L LVTTL/LVCMOS Compatible 3.3V Dual-Channel Optocouplers (10 Mb/s) Description The LTV-063L consists of a high efficient AlGaAs Light Emitting Diode and a high speed optical detector. This design
More information