DS26C31T/DS26C31M CMOS Quad TRI-STATE Differential Line Driver

Size: px
Start display at page:

Download "DS26C31T/DS26C31M CMOS Quad TRI-STATE Differential Line Driver"

Transcription

1 DS26C31T/DS26C31M CMOS Quad TRI-STATE Differential Line Driver General Description The DS26C31 is a quad differential line driver designed for digital data transmission over balanced lines. The DS26C31T meets all the requirements of EIA standard RS-422 while retaining the low power characteristics of CMOS. The DS26C31M is compatible with EIA standard RS-422; however, one exception in test methodology is taken (Note 8). This enables the construction of serial and terminal interfaces while maintaining minimal power consumption. The DS26C31 accepts TTL or CMOS input levels and translates these to RS-422 output levels. This part uses special output circuitry that enables the drivers to power down without loading down the bus. This device has enable and disable circuitry common to all four drivers. The DS26C31 is pin compatible to the AM26LS31 and the DS26LS31. Connection Diagrams Dual-In-Line Package DS Top View Order Number DS26C31TM or DS26C31TN See NS Package Number M16A or N16E For Complete Military Product Specifications, refer to the appropriate SMD or MDS. Order Number DS26C31ME/883, DS26C31MJ/883 or DS26C31MW/883 See NS Package Number E20A, J16A or W16A All inputs are protected against damage due to electrostatic discharge by diodes to V CC and ground. Features n TTL input compatible n Typical propagation delays: 6 ns n Typical output skew: 0.5 ns n Outputs will not load line when V CC = 0V n DS26C31T meets the requirements of EIA standard RS-422 n Operation from single 5V supply n TRI-STATE outputs for connection to system buses n Low quiescent current n Available in surface mount n Mil-Std-883C compliant 20-Lead Ceramic Leadless Chip Carrier (E) Truth Table June 1998 DS ENABLE ENABLE Input Non-Inverting Inverting Output Output L H X Z Z All other L L H combinations of H H L enable inputs DS26C31T/DS26C31M CMOS Quad TRI-STATE Differential Line Driver L = Low logic state X = Irrelevant H = High logic state Z = TRI-STATE (high impedance) TRI-STATE is a registered trademark of National Semiconductor Corporation. FACT is a trademark of National Semiconductor Corporation National Semiconductor Corporation DS

2 Absolute Maximum Ratings (Notes 1, 2) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (V CC ) 0.5V to 7.0V DC Input Voltage (V IN ) 1.5V to V CC +1.5V DC Output Voltage (V OUT ) 0.5V to 7V Clamp Diode Current (I IK,I OK ) ±20 ma DC Output Current, per pin (I OUT ) ±150 ma DC V CC or GND Current, per pin (I CC ) ±150 ma Storage Temperature Range (T STG ) 65 C to +150 C DC Electrical Characteristics V CC = 5V ± 10% (unless otherwise specified) (Note 4) Max. Power Dissipation (P D C (Note 3) Ceramic J Pkg mw Plastic N Pkg mw SOIC M Pkg mw Ceramic W Pkg mw Ceramic E Pkg mw Lead Temperature (T L ) (Soldering, 4 sec.) 260 C This device does not meet 2000V ESD Rating. (Note 13) Operating Conditions Min Max Units Supply Voltage (V CC ) V DC Input or Output Voltage (V IN,V OUT ) 0 V CC V Operating Temperature Range (T A ) DS26C31T C DS26C31M C Input Rise or Fall Times (t r,t f ) 500 ns Symbol Parameter Conditions Min Typ Max Units V IH High Level Input Voltage 2.0 V V IL Low Level Input Voltage 0.8 V V OH High Level Output Voltage V IN = V IH or V IL, V I OUT = 20 ma V OL Low Level Output V IN = V IH or V IL, V Voltage I OUT = 20 ma V T Differential Output R L = 100Ω V Voltage (Note 5) V T V T Difference In R L = 100Ω 0.4 V Differential Output (Note 5) V OS Common Mode R L = 100Ω V Output Voltage (Note 5) V OS V OS Difference In R L = 100Ω 0.4 V Common Mode Output (Note 5) I IN Input Current V IN = V CC, GND, V IH,orV IL ±1.0 µa I CC Quiescent Supply DS26C31T V IN = V CC or GND µa Current (Note 6) I OUT = 0µA V IN = 2.4V or 0.5V ma (Note 6) DS26C31M V IN = V CC or GND µa I OUT = 0µA V IN = 2.4V or 0.5V ma (Note 6) I OZ TRI-STATE Output V OUT = V CC or GND Leakage Current ENABLE = V IL ±0.5 ±5.0 µa ENABLE = V IH I SC Output Short V IN = V CC or GND ma Circuit Current (Notes 5, 7) 2

3 DC Electrical Characteristics (Continued) V CC = 5V ± 10% (unless otherwise specified) (Note 4) Symbol Parameter Conditions Min Typ Max Units I OFF Output Leakage Current DS26C31T V OUT = 6V 100 µa Power Off (Note 5) V CC = 0V V OUT = 0.25V 100 µa DS26C31M V OUT = 6V 100 µa V CC = 0V V OUT = 0V 100 µa (Note 8) Note 1: Absolute Maximum Ratings are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should be operated at these limits. The table of Electrical Characteristics provide conditions for actual device operation. Note 2: Unless otherwise specified, all voltages are referenced to ground. All currents into device pins are positive, all currents out of device pins are negative. Note 3: Ratings apply to ambient temperature at 25 C. Above this temperature derate N package at mw/ C, J package mw/ C, M package 9.80 mw/ C, E package mw/ C, and W package 6.75 mw/ C. Note 4: Unless otherwise specified, min/max limits apply across the recommended operating temperature range. All typicals are given for V CC = 5V and T A = 25 C. Note 5: See EIA Specification RS-422 for exact test conditions. Note 6: Measured per input. All other inputs at V CC or GND. Note 7: This is the current sourced when a high output is shorted to ground. Only one output at a time should be shorted. Note 8: The DS26C31M ( 55 C to +125 C) is tested with V OUT between +6V and 0V while RS-422A condition is +6V and 0.25V. Switching Characteristics V CC = 5V ±10%, t r 6 ns, t f 6ns(Figures 1, 2, 3, 4) (Note 4) Symbol Parameter Conditions Min Typ Max Units DS26C31T CS26C31M t PLH,t PHL Propagation Delays S1 Open ns Input to Output Skew (Note 9) S1 Open ns t TLH,t THL Differential Output Rise S1 Open ns And Fall Times t PZH Output Enable Time S1 Closed ns t PZL Output Enable Time S1 Closed ns t PHZ Output Disable Time S1 Closed ns (Note 10) t PLZ Output Disable Time S1 Closed ns (Note 10) C PD Power Dissipation 50 pf Capacitance (Note 11) C IN Input Capacitance 6 pf Note 9: Skew is defined as the difference in propagation delays between complementary outputs at the 50% point. Note 10: Output disable time is the delay from ENABLE or ENABLE being switched to the output transistors turning off. The actual disable times are less than indicated due to the delay added by the RC time constant of the load. Note 11: C PD determines the no load dynamic power consumption, P D = C PD V CC 2f+I CC V CC, and the no load dynamic current consumption, I S = C PD V CC f+ I CC. Comparison Table of Switching Characteristics into LS-Type Load V CC = 5V, T A = 25 C, t r 6 ns, t f 6ns(Figures 2, 4, 5, 6) (Note 12) Symbol Parameter Conditions DS26C31T DS26LS31C Units Typ Max Typ Max t PLH,t PHL Propagation Delays C L = 30 pf Input to Output S1 Closed ns S2 Closed Skew (Note 9) C L = 30 pf S1 Closed ns S2 Closed 3

4 Comparison Table of Switching Characteristics into LS-Type Load (Continued) V CC = 5V, T A = 25 C, t r 6 ns, t f 6ns(Figures 2, 4, 5, 6) (Note 12) Symbol Parameter Conditions DS26C31T DS26LS31C Units Typ Max Typ Max t THL,t TLH Differential Output Rise C L = 30 pf and Fall Times S1 Closed 4 6 ns S2 Closed t PLZ Output Disable Time C L = 10 pf (Note 10) S1 Closed ns S2 Open t PHZ Output Disable Time C L = 10 pf (Note 10) S1 Open ns S2 Closed t PZL Output Enable Time C L = 30 pf S1 Closed ns S2 Open t PZH Output Enable Time C L = 30 pf S1 Open ns S2 Closed Note 12: This table is provided for comparison purposes only. The values in this table for the DS26C31 reflect the performance of the device but are not tested or guaranteed. Note 13: ESD Rating: HBM (1.5 kω, 100 pf) Inputs 1500V Outputs 1000V EIAJ (0Ω, 200 pf) 350V Logic Diagram AC Test Circuit and Switching Time Waveforms DS Note: C1 = C2 = C3 = 40 pf (Including Probe and Jig Capacitance), R1 = R2 = 50Ω, R3=500Ω. FIGURE 1. AC Test Circuit DS

5 AC Test Circuit and Switching Time Waveforms (Continued) FIGURE 2. Propagation Delays DS FIGURE 3. Enable and Disable Times DS DS Input pulse; f = 1 MHz, 50%; t r 6 ns, t f 6ns FIGURE 4. Differential Rise and Fall Times 5

6 AC Test Circuit and Switching Time Waveforms (Continued) DS FIGURE 5. Load AC Test Circuit for LS-Type Load FIGURE 6. Enable and Disable Times for LS-Type Load DS Typical Applications Two-Wire Balanced System, RS-422 *R T is optional although highly recommended to reduce reflection. DS

7 Typical Performance Characteristics Differential Propagation Delay vs Temperature Differential Propagation Delay vs Power Supply Voltage Differential Skew vs Temperature DS DS DS Differential Skew vs Power Supply Voltage Differential Transition Time vs Temperature Differential Transition Time vs Power Supply Voltage DS DS DS Complementary Skew vs Temperature Complementary Skew vs Power Supply Voltage Differential Output Voltage vs Output Current DS DS DS

8 Typical Performance Characteristics (Continued) Differential Output Voltage vs Output Current Output High Voltage vs Output High Current Output High Voltage vs Output High Current DS DS DS Output Low Voltage vs Output Low Current Output Low Voltage vs Output Low Current Supply Current vs Temperature DS DS DS Supply Current vs Power Supply Voltage No Load Supply Current vs Data Rate Loaded Supply Current vs Data Rate DS DS DS

9 Typical Performance Characteristics (Continued) Output Short Circuit Current vs Temperature Output Short Circuit Current vs Power Supply Voltage DS DS

10 Physical Dimensions inches (millimeters) unless otherwise noted 20-Lead Ceramic Leadless Chip Carrier (E) Order Number DS26C31ME/883 NS Package Number E20A 16-Lead Ceramic Dual-In-Line Package (J) Order Number DS26C31MJ/883 NS Package Number J16A 10

11 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Molded Package Small Outline (M) Order Number DS26C31TM NS Package Number M16A 16-Lead Molded Dual-In-Line Package (N) Order Number DS26C31TN NS Package Number N16E 11

12 DS26C31T/DS26C31M CMOS Quad TRI-STATE Differential Line Driver Physical Dimensions inches (millimeters) unless otherwise noted (Continued) LIFE SUPPORT POLICY NATIONAL S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DE- VICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL SEMI- CONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 16-Lead Ceramic Flatpak Package (W) Order Number DS26C31MW/883 NS Package Number W16A 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Corporation Americas Tel: Fax: support@nsc.com National Semiconductor Europe Fax: +49 (0) europe.support@nsc.com Deutsch Tel: +49 (0) English Tel: +49 (0) Français Tel: +49 (0) Italiano Tel: +49 (0) National Semiconductor Asia Pacific Customer Response Group Tel: Fax: sea.support@nsc.com National Semiconductor Japan Ltd. Tel: Fax: National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.

Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. DS34C87T CMOS Quad TRI-STATE Differential Line Driver General Description

More information

DS1488 Quad Line Driver

DS1488 Quad Line Driver DS1488 Quad Line Driver General Description The DS1488 is a quad line driver which converts standard TTL input logic levels through one stage of inversion to output levels which meet EIA Standard RS-232D

More information

DS90C031 LVDS Quad CMOS Differential Line Driver

DS90C031 LVDS Quad CMOS Differential Line Driver DS90C031 LVDS Quad CMOS Differential Line Driver General Description The DS90C031 is a quad CMOS differential line driver designed for applications requiring ultra low power dissipation and high data rates.

More information

DS3486 Quad RS-422, RS-423 Line Receiver

DS3486 Quad RS-422, RS-423 Line Receiver DS3486 Quad RS-422, RS-423 Line Receiver General Description National s quad RS-422, RS-423 receiver features four independent receivers which comply with EIA Standards for the electrical characteristics

More information

Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. DS26LS31C/DS26LS31M Quad High Speed Differential Line Driver General Description

More information

54FCT240 Octal Buffer/Line Driver with TRI-STATE Outputs

54FCT240 Octal Buffer/Line Driver with TRI-STATE Outputs 54FCT240 Octal Buffer/Line Driver with TRI-STATE Outputs General Description The 54FCT240 is an octal buffer and line driver designed to be employed as a memory address driver, clock driver and bus oriented

More information

DS3695/DS3695T/DS3696/DS3697 Multipoint RS485/RS422 Transceivers/Repeaters

DS3695/DS3695T/DS3696/DS3697 Multipoint RS485/RS422 Transceivers/Repeaters DS3695/DS3695T/DS3696/DS3697 Multipoint RS485/RS422 Transceivers/Repeaters General Description The DS3695, DS3696, and DS3697 are high speed differential TRI-STATE bus/line transceivers/repeaters designed

More information

DS90C032 LVDS Quad CMOS Differential Line Receiver

DS90C032 LVDS Quad CMOS Differential Line Receiver DS90C032 LVDS Quad CMOS Differential Line Receiver General Description TheDS90C032 is a quad CMOS differential line receiver designed for applications requiring ultra low power dissipation and high data

More information

DS36C279 Low Power EIA-RS-485 Transceiver with Sleep Mode

DS36C279 Low Power EIA-RS-485 Transceiver with Sleep Mode DS36C279 Low Power EIA-RS-485 Transceiver with Sleep Mode General Description The DS36C279 is a low power differential bus/line transceiver designed to meet the requirements of RS-485 Standard for multipoint

More information

DS7830/DS8830 Dual Differential Line Driver

DS7830/DS8830 Dual Differential Line Driver DS7830/DS8830 Dual Differential Line Driver General Description The DS7830/DS8830 is a dual differential line driver that also performs the dual four-input NAND or dual four-input AND function. TTL (Transistor-Transistor-Logic)

More information

54AC00 54ACT00 Quad 2-Input NAND Gate

54AC00 54ACT00 Quad 2-Input NAND Gate 54AC00 54ACT00 Quad 2-Input NAND Gate General Description The AC/ ACT00 contains four 2-input NAND gates. Features n I CC reduced by 50% Logic Symbol IEEE/IEC n Outputs source/sink 24 ma n ACT00 has TTL-compatible

More information

DS96172/DS96174 RS-485/RS-422 Quad Differential Line Drivers

DS96172/DS96174 RS-485/RS-422 Quad Differential Line Drivers DS96172/DS96174 RS-485/RS-422 Quad Differential Line Drivers General Description The DS96172 and DS96174 are high speed quad differential line drivers designed to meet EIA Standard RS-485. The devices

More information

Distributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. DS26LV31T 3V Enhanced CMOS Quad Differential Line Driver General Description

More information

DS16F95, DS36F95 EIA-485/EIA-422A Differential Bus Transceiver

DS16F95, DS36F95 EIA-485/EIA-422A Differential Bus Transceiver DS16F95, DS36F95 EIA-485/EIA-422A Differential Bus Transceiver General Description The DS16F95/DS36F95 Differential Bus Transceiver is a monolithic integrated circuit designed for bidirectional data communication

More information

DS7830 Dual Differential Line Driver

DS7830 Dual Differential Line Driver DS7830 Dual Differential Line Driver General Description The DS7830 is a dual differential line driver that also performs the dual four-input NAND or dual four-input AND function. TTL (Transistor-Transistor-Logic)

More information

DS3486 Quad RS-422, RS-423 Line Receiver

DS3486 Quad RS-422, RS-423 Line Receiver Quad RS-422, RS-423 Line Receiver General Description National s quad RS-422, RS-423 receiver features four independent receivers which comply with EIA Standards for the electrical characteristics of balanced/unbalanced

More information

DS8922/DS8922A/DS8923A TRI-STATE RS-422 Dual Differential Line Driver and Receiver Pairs

DS8922/DS8922A/DS8923A TRI-STATE RS-422 Dual Differential Line Driver and Receiver Pairs DS8922/DS8922A/DS8923A TRI-STATE RS-422 Dual Differential Line Driver and Receiver Pairs General Description The DS8922/22A and DS8923A are Dual Differential Line Driver and Receiver pairs. These devices

More information

DS75451/2/3 Series Dual Peripheral Drivers

DS75451/2/3 Series Dual Peripheral Drivers DS75451/2/3 Series Dual Peripheral Drivers General Description The DS7545X series of dual peripheral drivers is a family of versatile devices designed for use in systems that use TTL logic. Typical applications

More information

DS90C032B LVDS Quad CMOS Differential Line Receiver

DS90C032B LVDS Quad CMOS Differential Line Receiver LVDS Quad CMOS Differential Line Receiver General Description TheDS90C032B is a quad CMOS differential line receiver designed for applications requiring ultra low power dissipation and high data rates.

More information

Low Power Octal ECL/TTL Bi-Directional Translator with Latch

Low Power Octal ECL/TTL Bi-Directional Translator with Latch 100328 Low Power Octal ECL/TTL Bi-Directional Translator with Latch General Description The 100328 is an octal latched bi-directional translator designed to convert TTL logic levels to 100K ECL logic levels

More information

DS1489/DS1489A Quad Line Receiver

DS1489/DS1489A Quad Line Receiver DS1489/DS1489A Quad Line Receiver General Description The DS1489/DS1489A are quad line receivers designed to interface data terminal equipment with data communications equipment. They are constructed on

More information

DIFFERENTIAL DRIVER CHARACTERISTICS

DIFFERENTIAL DRIVER CHARACTERISTICS DS36C278 Low Power Multipoint EIA-RS-485 Transceiver General Description The DS36C278 is a low power differential bus/line transceiver designed to meet the requirements of RS-485 standard for multipoint

More information

DS3662 Quad High Speed Trapezoidal Bus Transceiver

DS3662 Quad High Speed Trapezoidal Bus Transceiver DS3662 Quad High Speed Trapezoidal Bus Transceiver General Description The DS3662 is a quad high speed Schottky bus transceiver intended for use with terminated 120Ω impedance lines. It is specifically

More information

DS485 Low Power RS-485/RS-422 Multipoint Transceiver

DS485 Low Power RS-485/RS-422 Multipoint Transceiver DS485 Low Power RS-485/RS-422 Multipoint Transceiver General Description The DS485 is a low-power transceiver for RS-485 and RS-422 communication. The device contains one driver and one receiver. The drivers

More information

54ABT Bit Transparent Latch with TRI-STATE Outputs

54ABT Bit Transparent Latch with TRI-STATE Outputs 54ABT16373 16-Bit Transparent Latch with TRI-STATE Outputs General Description The ABT16373 contains sixteen non-inverting latches with TRI-STATE outputs and is intended for bus oriented applications.

More information

DS90LV017A LVDS Single High Speed Differential Driver

DS90LV017A LVDS Single High Speed Differential Driver DS90LV017A LVDS Single High Speed Differential Driver General Description The DS90LV017A is a single LVDS driver device optimized for high data rate and low power applications. The DS90LV017A is a current

More information

DS90C402 Dual Low Voltage Differential Signaling (LVDS) Receiver

DS90C402 Dual Low Voltage Differential Signaling (LVDS) Receiver DS90C402 Dual Low Voltage Differential Signaling (LVDS) Receiver General Description The DS90C402 is a dual receiver device optimized for high data rate and low power applications. This device along with

More information

DS36C279 Low Power EIA-RS-485 Transceiver with Sleep Mode

DS36C279 Low Power EIA-RS-485 Transceiver with Sleep Mode DS36C279 Low Power EIA-RS-485 Transceiver with Sleep Mode General Description The DS36C279 is a low power differential bus/line transceiver designed to meet the requirements of RS-485 Standard for multipoint

More information

54AC08 Quad 2-Input AND Gate

54AC08 Quad 2-Input AND Gate 08 Quad 2-Input AND Gate General Description The AC08 contains four, 2-input AND gates. Features n I CC reduced by 50% n Outputs source/sink 24 ma Logic Symbol IEEE/IEC July 2003 n Standard Microcircuit

More information

DS7833 DS8833 DS7835 DS8835 Quad TRI-STATE Bus Transceivers

DS7833 DS8833 DS7835 DS8835 Quad TRI-STATE Bus Transceivers DS7833 DS8833 DS7835 DS8835 Quad TRI-STATE Bus Transceivers General Description This family of TRI-STATE bus transceivers offers extreme versatility in bus organized data transmission systems The data

More information

DS14185 EIA/TIA Driver x 5 Receiver

DS14185 EIA/TIA Driver x 5 Receiver DS14185 EIA/TIA-232 General Description 3 Driver x 5 Receiver The DS14185 is a three driver, five receiver device which conforms to the EIA/TIA-232-E standard. The flow-through pinout facilitates simple

More information

54AC191 Up/Down Counter with Preset and Ripple Clock

54AC191 Up/Down Counter with Preset and Ripple Clock 54AC191 Up/Down Counter with Preset and Ripple Clock General Description The AC191 is a reversible modulo 16 binary counter. It features synchronous counting and asynchronous presetting. The preset feature

More information

DS9637A Dual Differential Line Receiver

DS9637A Dual Differential Line Receiver Dual Differential Line Receiver General Description The DS9637A is a Schottky dual differential line receiver which has been specifically designed to satisfy the requirements of EIA Standards RS-422 and

More information

LM161/LM261/LM361 High Speed Differential Comparators

LM161/LM261/LM361 High Speed Differential Comparators LM161/LM261/LM361 High Speed Differential Comparators General Description The LM161/LM261/LM361 is a very high speed differential input, complementary TTL output voltage comparator with improved characteristics

More information

LMS75LBC176 Differential Bus Transceivers

LMS75LBC176 Differential Bus Transceivers LMS75LBC176 Differential Bus Transceivers General Description The LMS75LBC176 is a differential bus/line transceiver designed for bidirectional data communication on multipoint bus transmission lines.

More information

DS14C238 Single Supply TIA/EIA x 4 Driver/Receiver

DS14C238 Single Supply TIA/EIA x 4 Driver/Receiver Single Supply TIA/EIA-232 4x4Driver/Receiver General Description The DS14C238 is a four driver, four receiver device which conforms to the TIA/EIA-232-E standard and CCITT V.28 recommendations. This device

More information

DS36950 Quad Differential Bus Transceiver

DS36950 Quad Differential Bus Transceiver DS36950 Quad Differential Bus Transceiver General Description The DS36950 is a low power, space-saving quad EIA-485 differential bus transceiver especially suited for high speed, parallel, multipoint,

More information

74VHC Channel Analog Multiplexer 74VHC4052 Dual 4-Channel Analog Multiplexer 74VHC4053 Triple 2-Channel Analog Multiplexer

74VHC Channel Analog Multiplexer 74VHC4052 Dual 4-Channel Analog Multiplexer 74VHC4053 Triple 2-Channel Analog Multiplexer 74VHC4051 8-Channel Analog Multiplexer 74VHC4052 Dual 4-Channel Analog Multiplexer 74VHC4053 Triple 2-Channel Analog Multiplexer General Description Ordering Code: These multiplexers are digitally controlled

More information

LM160/LM360 High Speed Differential Comparator

LM160/LM360 High Speed Differential Comparator High Speed Differential Comparator General Description The is a very high speed differential input, complementary TTL output voltage comparator with improved characteristics over the µa760/µa760c, for

More information

DS75176B/DS75176BT Multipoint RS-485/RS-422 Transceivers

DS75176B/DS75176BT Multipoint RS-485/RS-422 Transceivers Multipoint RS-485/RS-422 Transceivers General Description The DS75176B is a high speed differential TRI-STATE bus/line transceiver designed to meet the requirements of EIA standard RS485 with extended

More information

54F/74F04 Hex Inverter

54F/74F04 Hex Inverter 54F/74F04 Hex Inverter General Description This device contains six independent gates, each of which performs the logic INVERT function. Ordering Code: See Section 0 Features n Guaranteed 4000V minimum

More information

DS485 Low Power RS-485/RS-422 Multipoint Transceiver

DS485 Low Power RS-485/RS-422 Multipoint Transceiver Low Power RS-485/RS-422 Multipoint Transceiver General Description The DS485 is a low-power transceiver for RS-485 and RS- 422 communication. The device contains one driver and one receiver. The drivers

More information

DS36C278 Low Power Multipoint EIA-RS-485 Transceiver

DS36C278 Low Power Multipoint EIA-RS-485 Transceiver DS36C278 Low Power Multipoint EIA-RS-485 Transceiver General Description The DS36C278 is a low power differential bus line transceiver designed to meet the requirements of RS-485 standard for multipoint

More information

DS2003 High Current/Voltage Darlington Drivers

DS2003 High Current/Voltage Darlington Drivers DS2003 High Current/Voltage Darlington Drivers General Description The DS2003 is comprised of seven high voltage, high current NPN Darlington transistor pairs. All units feature common emitter, open collector

More information

DS34LV86T 3V Enhanced CMOS Quad Differential Line Receiver

DS34LV86T 3V Enhanced CMOS Quad Differential Line Receiver 3V Enhanced CMOS Quad Differential Line Receiver General Description The DS34LV86T is a high speed quad differential CMOS receiver that meets the requirements of both TIA/EIA-422-B and ITU-T V.11. The

More information

MM74HC132 Quad 2-Input NAND Schmitt Trigger

MM74HC132 Quad 2-Input NAND Schmitt Trigger Quad 2-Input NAND Schmitt Trigger General Description The utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as well as the capability

More information

Low Power Hex TTL-to-ECL Translator

Low Power Hex TTL-to-ECL Translator 100324 Low Power Hex TTL-to-ECL Translator General Description The 100324 is a hex translator, designed to convert TTL logic levels to 100K ECL logic levels. The inputs are compatible with standard or

More information

74F573 Octal D-Type Latch with 3-STATE Outputs

74F573 Octal D-Type Latch with 3-STATE Outputs 74F573 Octal D-Type Latch with 3-STATE Outputs General Description The F573 is a high speed octal latch with buffered common Latch Enable (LE) and buffered common Output Enable (OE) inputs. This device

More information

MM74HCU04 Hex Inverter

MM74HCU04 Hex Inverter MM74HCU04 Hex Inverter General Description The MM74HCU04 inverters utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard

More information

MM74HC132 Quad 2-Input NAND Schmitt Trigger

MM74HC132 Quad 2-Input NAND Schmitt Trigger Quad 2-Input NAND Schmitt Trigger General Description The MM74HC132 utilizes advanced silicon-gate CMOS technology to achieve the low power dissipation and high noise immunity of standard CMOS, as well

More information

MM74HC00 Quad 2-Input NAND Gate

MM74HC00 Quad 2-Input NAND Gate Quad 2-Input NAND Gate General Description The MM74HC00 NAND gates utilize advanced silicon-gate CMOS technology to achieve operating speeds similar to LS-TTL gates with the low power consumption of standard

More information

DS8922 DS8922A DS8923 DS8923A TRI-STATE RS-422 Dual Differential Line Driver and Receiver Pairs

DS8922 DS8922A DS8923 DS8923A TRI-STATE RS-422 Dual Differential Line Driver and Receiver Pairs February 1996 DS8922 DS8922A DS8923 DS8923A TRI-STATE RS-422 Dual Differential Line Driver and Receiver Pairs General Description The DS8922 22A and DS8923 23A are Dual Differential Line Driver and Receiver

More information

Order codes Temperature range Package Packaging

Order codes Temperature range Package Packaging CMOS quad 3-state differential line driver Features TTL input compatible Typical propagation delay: 6 ns Typical output skew: 0.5 ns Output will not load line when V CC = 0 V Meets the requirements of

More information

74F540 74F541 Octal Buffer/Line Driver with 3-STATE Outputs

74F540 74F541 Octal Buffer/Line Driver with 3-STATE Outputs 74F540 74F541 Octal Buffer/Line Driver with 3-STATE Outputs General Description The F540 and F541 are similar in function to the F240 and F244 respectively, except that the inputs and outputs are on opposite

More information

LM1558/LM1458 Dual Operational Amplifier

LM1558/LM1458 Dual Operational Amplifier LM1558/LM1458 Dual Operational Amplifier General Description The LM1558 and the LM1458 are general purpose dual operational amplifiers. The two amplifiers share a common bias network and power supply leads.

More information

DS DS Series Dual Peripheral Drivers

DS DS Series Dual Peripheral Drivers DS55451 2 3 4 DS75451 2 3 4 Series Dual Peripheral Drivers General Description Features Y The DS7545X series of dual peripheral drivers is a family of versatile devices designed for use in systems that

More information

LMS485 5V Low Power RS-485 / RS-422 Differential Bus Transceiver

LMS485 5V Low Power RS-485 / RS-422 Differential Bus Transceiver 5V Low Power RS-485 / RS-422 Differential Bus Transceiver General Description The LMS485 is a low power differential bus/line transceiver designed for high speed bidirectional data communication on multipoint

More information

SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER

SP26LV431 HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER HIGH SPEED +3.3V QUAD RS-422 DIFFERENTIAL LINE DRIVER JUNE 2011 REV. 1.1.1 GENERAL DESCRIPTION The SP26LV431 is a quad differential line driver that meets the specifications of the EIA standard RS-422

More information

FST Bit Low Power Bus Switch

FST Bit Low Power Bus Switch 2-Bit Low Power Bus Switch General Description The FST3306 is a 2-bit ultra high-speed CMOS FET bus switch with TTL-compatible active LOW control inputs. The low on resistance of the switch allows inputs

More information

DS14196 EIA/TIA Driver x 3 Receiver

DS14196 EIA/TIA Driver x 3 Receiver EIA/TIA-232 5 Driver x 3 Receiver General Description The is a five driver, three receiver device which conforms to the EIA/TIA-232-E and the ITU-T V.28 standards. The flow-through pinout facilitates simple

More information

54LS125A DM54LS125A DM74LS125A Quad TRI-STATE Buffers

54LS125A DM54LS125A DM74LS125A Quad TRI-STATE Buffers 54LS125A DM54LS125A DM74LS125A Quad TRI-STATE Buffers General Description This device contains four independent gates each of which performs a non-inverting buffer function The outputs have the TRI-STATE

More information

Low Power Quint AND/NAND Gate

Low Power Quint AND/NAND Gate 100304 Low Power Quint AND/NAND Gate General Description The 100304 is monolithic quint AND/NAND gate. The Function output is the wire-nor of all five AND gate outputs. All inputs have 50 kω pull-down

More information

MM74HC4066 Quad Analog Switch

MM74HC4066 Quad Analog Switch MM74HC4066 Quad Analog Switch General Description The MM74HC4066 devices are digitally controlled analog switches utilizing advanced silicon-gate CMOS technology. These switches have low ON resistance

More information

LMS1487E Low Power RS-485 / RS-422 Differential Bus Transceiver

LMS1487E Low Power RS-485 / RS-422 Differential Bus Transceiver Low Power RS-485 / RS-422 Differential Bus Transceiver General Description The LMS1487E is a low power differential bus/line transceiver designed for high speed bidirectional data communication on multipoint

More information

SCAN16512 Low Voltage Universal 16-bit IEEE Bus Transceiver with TRI-STATE Outputs

SCAN16512 Low Voltage Universal 16-bit IEEE Bus Transceiver with TRI-STATE Outputs SCAN16512 Low Voltage Universal 16-bit IEEE 1149.1 Bus Transceiver with TRI-STATE Outputs General Description The SCAN16512 is a high speed, low-power universal bus transceiver featuring data inputs organized

More information

74F00 Quad 2-Input NAND Gate

74F00 Quad 2-Input NAND Gate 74F00 Quad 2-Input NAND Gate General Description This device contains four independent gates, each of which performs the logic NAND function. Ordering Code: Features n Guaranteed 4000V minimum ESD protection

More information

CD4069UBC Inverter Circuits

CD4069UBC Inverter Circuits CD4069UBC Inverter Circuits General Description The CD4069UB consists of six inverter circuits and is manufactured using complementary MOS (CMOS) to achieve wide power supply operating range, low power

More information

74LCX125 Low Voltage Quad Buffer with 5V Tolerant Inputs and Outputs

74LCX125 Low Voltage Quad Buffer with 5V Tolerant Inputs and Outputs Low Voltage Quad Buffer with 5V Tolerant Inputs and Outputs General Description The LCX125 contains four independent non-inverting buffers with 3-STATE outputs. The inputs tolerate voltages up to 7V allowing

More information

NC7SZ32 TinyLogic UHS 2-Input OR Gate

NC7SZ32 TinyLogic UHS 2-Input OR Gate NC7SZ32 TinyLogic UHS 2-Input OR Gate General Description The NC7SZ32 is a single 2-Input OR Gate from Fairchild s Ultra High Speed Series of TinyLogic. The device is fabricated with advanced CMOS technology

More information

DS90LV032A 3V LVDS Quad CMOS Differential Line Receiver

DS90LV032A 3V LVDS Quad CMOS Differential Line Receiver DS90LV032A 3V LVDS Quad CMOS Differential Line Receiver General Description The DS90LV032A is a quad CMOS differential line receiver designed for applications requiring ultra low power dissipation and

More information

DM74LS75 Quad Latches

DM74LS75 Quad Latches DM74LS75 uad Latches General Description These latches are ideally suited for use as temporary storage for binary information between processing units and input/output or indicator units. Information present

More information

74F794 8-Bit Register with Readback

74F794 8-Bit Register with Readback 74F794 8-Bit Register with Readback General Description The F794 is an 8-bit register with readback capability designed to store data as well as read the register information back onto the data bus. The

More information

74FR Bit Bidirectional Transceiver with 3-STATE Outputs

74FR Bit Bidirectional Transceiver with 3-STATE Outputs 74FR9245 9-Bit Bidirectional Transceiver with 3-STATE Outputs General Description The FR9245 contains nine non-inverting bidirectional buffers with 3-STATE outputs and is intended for bus-oriented applications.

More information

DS75160A DS75161A DS75162A IEEE-488 GPIB Transceivers

DS75160A DS75161A DS75162A IEEE-488 GPIB Transceivers DS75160A DS75161A DS75162A IEEE-488 GPIB Transceivers General Description This family of high-speed-schottky 8-channel bi-directional transceivers is designed to interface TTL MOS logic to the IEEE Standard

More information

LM392/LM2924 Low Power Operational Amplifier/Voltage Comparator

LM392/LM2924 Low Power Operational Amplifier/Voltage Comparator LM392/LM2924 Low Power Operational Amplifier/Voltage Comparator General Description The LM392 series consists of 2 independent building block circuits. One is a high gain, internally frequency compensated

More information

FSTD Bit Bus Switch with Level Shifting

FSTD Bit Bus Switch with Level Shifting FSTD16861 20-Bit Bus Switch with Level Shifting General Description The Fairchild Switch FSTD16861 provides 20-bits of highspeed CMOS TTL-compatible bus switching. The low On Resistance of the switch allows

More information

Low Power Hex TTL-to-ECL Translator

Low Power Hex TTL-to-ECL Translator 100324 Low Power Hex TTL-to-ECL Translator General Description The 100324 is a hex translator, designed to convert TTL logic levels to 100K ECL logic levels. The inputs are compatible with standard or

More information

74ALVC Low Voltage 16-Bit Bidirectional Transceiver with 3.6V Tolerant Inputs and Outputs and 26Ω Series Resistors in A Port Outputs

74ALVC Low Voltage 16-Bit Bidirectional Transceiver with 3.6V Tolerant Inputs and Outputs and 26Ω Series Resistors in A Port Outputs 74ALVC162245 Low Voltage 16-Bit Bidirectional Transceiver with 3.6V Tolerant Inputs and Outputs and 26Ω Series Resistors in A Port Outputs General Description The ALVC162245 contains sixteen non-inverting

More information

LM9044 Lambda Sensor Interface Amplifier

LM9044 Lambda Sensor Interface Amplifier LM9044 Lambda Sensor Interface Amplifier General Description The LM9044 is a precision differential amplifier specifically designed for operation in the automotive environment. Gain accuracy is guaranteed

More information

LM723/LM723C Voltage Regulator

LM723/LM723C Voltage Regulator LM723/LM723C Voltage Regulator General Description The LM723/LM723C is a voltage regulator designed primarily for series regulator applications. By itself, it will supply output currents up to 150 ma;

More information

DM74LS30 8-Input NAND Gate

DM74LS30 8-Input NAND Gate DM74LS30 8-Input NAND Gate General Description This device contains a single gate which performs the logic NAND function. Features n Alternate Military/Aerospace device (54LS30) is available. Contact a

More information

MM74HC4051 MM74HC4052 MM74HC Channel Analog Multiplexer Dual 4-Channel Analog Multiplexer Triple 2-Channel Analog Multiplexer

MM74HC4051 MM74HC4052 MM74HC Channel Analog Multiplexer Dual 4-Channel Analog Multiplexer Triple 2-Channel Analog Multiplexer 8-Channel Analog Multiplexer Dual 4-Channel Analog Multiplexer Triple 2-Channel Analog Multiplexer General Description The MM74HC4051, MM74HC4052 and MM74HC4053 multiplexers are digitally controlled analog

More information

FST32X Bit Bus Switch

FST32X Bit Bus Switch FST32X245 16-Bit Bus Switch General Description The Fairchild Switch FST32X245 provides 16-bits of high speed CMOS TTL-compatible bus switching in a standard flow-through mode. The low On Resistance of

More information

DM74ALS373 Octal D-Type TRI-STATE Transparent Latch

DM74ALS373 Octal D-Type TRI-STATE Transparent Latch DM74ALS373 Octal D-Type TRI-STATE Transparent Latch General Description These 8-bit registers feature totem-pole TRI-STATE outputs designed specifically for driving highly-capacitive or relatively low-impedance

More information

SCAN16512A Low Voltage Universal 16-bit IEEE Bus Transceiver with TRI-STATE Outputs

SCAN16512A Low Voltage Universal 16-bit IEEE Bus Transceiver with TRI-STATE Outputs Low Voltage Universal 16-bit IEEE 1149.1 Bus Transceiver with TRI-STATE Outputs General Description The SCAN16512A is a high speed, low-power universal bus transceiver featuring data inputs organized into

More information

74F14 Hex Inverter Schmitt Trigger

74F14 Hex Inverter Schmitt Trigger 74F14 Hex Inverter Schmitt Trigger General Description The F14 contains six logic inverters which accept standard TTL input signals and provide standard TTL output levels. They are capable of transforming

More information

DS91D180/DS91C180 Multipoint LVDS (M-LVDS) Line Driver/Receiver

DS91D180/DS91C180 Multipoint LVDS (M-LVDS) Line Driver/Receiver Multipoint LVDS (M-LVDS) Line Driver/Receiver General Description The DS91D180 and DS91C180 are high-speed differential M- LVDS single drivers/receivers designed for multipoint applications with multiple

More information

DM74ALS245A Octal 3-STATE Bus Transceiver

DM74ALS245A Octal 3-STATE Bus Transceiver DM74ALS245A Octal 3-STATE Bus Transceiver General Description This advanced low power Schottky device contains 8 pairs of 3-STATE logic elements configured as octal bus transceivers. These circuits are

More information

CD4066BC Quad Bilateral Switch

CD4066BC Quad Bilateral Switch Quad Bilateral Switch General Description The CD4066BC is a quad bilateral switch intended for the transmission or multiplexing of analog or digital signals. It is pin-for-pin compatible with CD4016BC,

More information

MM5452/MM5453 Liquid Crystal Display Drivers

MM5452/MM5453 Liquid Crystal Display Drivers MM5452/MM5453 Liquid Crystal Display Drivers General Description The MM5452 is a monolithic integrated circuit utilizing CMOS metal gate, low threshold enhancement mode devices. It is available in a 40-pin

More information

74VHC VHC VHC Channel Analog Multiplexer Dual 4-Channel Analog Multiplexer Triple 2-Channel Analog Multiplexer

74VHC VHC VHC Channel Analog Multiplexer Dual 4-Channel Analog Multiplexer Triple 2-Channel Analog Multiplexer April 1994 Revised April 1999 74VHC4051 74VHC4052 74VHC4053 8-Channel Analog Multiplexer Dual 4-Channel Analog Multiplexer Triple 2-Channel Analog Multiplexer General Description These multiplexers are

More information

LM567/LM567C Tone Decoder

LM567/LM567C Tone Decoder LM567/LM567C Tone Decoder General Description The LM567 and LM567C are general purpose tone decoders designed to provide a saturated transistor switch to ground when an input signal is present within the

More information

NC7SB3257 TinyLogic UHS 2:1 Multiplexer/Demultiplexer Bus Switch

NC7SB3257 TinyLogic UHS 2:1 Multiplexer/Demultiplexer Bus Switch TinyLogic UHS 2:1 Multiplexer/Demultiplexer Bus Switch General Description The NC7SB3257 is a high performance, 2:1 NMOS passgate multiplexer/demultiplexer from Fairchild s Ultra High Speed Series of TinyLogic.

More information

LM118/LM218/LM318 Operational Amplifiers

LM118/LM218/LM318 Operational Amplifiers LM118/LM218/LM318 Operational Amplifiers General Description The LM118 series are precision high speed operational amplifiers designed for applications requiring wide bandwidth and high slew rate. They

More information

FST Bit Low Power Bus Switch

FST Bit Low Power Bus Switch FST3384 10-Bit Low Power Bus Switch General Description The Fairchild Switch FST3384 provides 10 bits of highspeed CMOS TTL-compatible bus switches. The low on resistance of the switch allows inputs to

More information

CD4066BC Quad Bilateral Switch

CD4066BC Quad Bilateral Switch Quad Bilateral Switch General Description The CD4066BC is a quad bilateral switch intended for the transmission or multiplexing of analog or digital signals. It is pin-for-pin compatible with CD4016BC,

More information

ISO-9001 AS9120certi cation ClassQ Military

ISO-9001 AS9120certi cation ClassQ Military Datasheet RochesterElectronics ManufacturedComponents Rochester branded components are manufactured using eitherdie/wafers purchasedfrom theoriginalsuppliers orrochesterwafers recreated from the originalip.

More information

M74HCT244TTR OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (NON INVERTED)

M74HCT244TTR OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (NON INVERTED) OCTAL BUS BUFFER WITH 3 STATE OUTPUTS (NON INVERTED) HIGH SPEED: t PD = 15 ns (TYP.) at V CC = 4.5V LOW POWER DISSIPATION: I CC = 4µA(MAX.) at T A =25 C COMPATIBLE WITH TTL OUTPUTS : V IH = 2V (MIN.) V

More information

CD4046BM/CD4046BC Micropower Phase-Locked Loop

CD4046BM/CD4046BC Micropower Phase-Locked Loop CD4046BM/CD4046BC Micropower Phase-Locked Loop General Description The CD4046B micropower phase-locked loop (PLL) consists of a low power, linear, voltage-controlled oscillator (VCO), a source follower,

More information

DM74LS126A Quad 3-STATE Buffer

DM74LS126A Quad 3-STATE Buffer DM74LS126A Quad 3-STATE Buffer General Description This device contains four independent gates each of which performs a non-inverting buffer function. The outputs have the 3-STATE feature. When enabled,

More information