Installation Manual VHF RADIOTELEPHONE FM-8800D/8800S

Transcription

1 Installation Manual VHF RADIOTELEHONE FM-8800D/8800S System Configuration... ii Equipment Lists... iii. Mounting Connections Assembling console kit... - acking Lists... A- Outline Drawings... D- Interconnection Diagrams... S- All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

2 * * * *

3 SAFETY INSTRUCTIONS WARNING Hazardous voltage. Can shock, burn or cause serious injury. Do not work inside the equipment unless totally familiar with electrical circuits. Do not approach the antenna closer than 0.9 m (ME by FCC) when it is transmitting. The antenna emits radio waves which can be harmful to the human body. RF power density on antenna aperture Distance Description required by 00 W/m 0. m IEC FM-8800S 0 W/m 0. m IEC W/m 0.9 m ME by FCC 00 W/m 0. m IEC FM-8800D 0 W/m 0. m IEC W/m 0.9 m ME by FCC (ME: Minimum ermissible Exposure) Turn off the power at the mains switchboard before beginning the installation. ost a warning sign near the switchboard to indicate that power should not be applied while the equipment is being installed. Electrical shock, serious injury or fire can result if the power is not turned off or is applied while the equipment is being installed. CAUTION Attach securely protective earth to the ship's body. The protective earth (grounding) is required to the AC/DC power supply unit to prevent electrical shock. Confirm that the power supply voltage is compatible with the voltage rating of the equipment. Connection to the wrong power supply can cause fire or equipment damage. The voltage rating appears on the label at the rear of the display unit. Observe the compass safe distance to prevent deviation of a magnetic compass. FM-8800S FM-8800D IF-880 IF-880 HS-00 HS-8800 RB-8800 (W/HS-8800) RB-880 (W/HS-8800) R-40 RB-880-W (W/HS-880-W) Standard compass.45 m.45 m 0.85 m 0.75 m.50 m 0.40 m.0 m.50 m 0.90 m.55 m Steering compass 0.90 m 0.95 m 0.55 m 0.50 m 0.95 m 0.0 m 0.80 m.00 m 0.60 m.00 m i

4 SYSTEM CONFIGURATION VHF Antenna CH 70 RX Antenna VHF console RC-8800 Wing handset MAX sets T/R AF output for VDR Handset HS-00 Transceiver Unit FM-8800D FM-8800S Junction Box* IF-880 IEC66- input DSC information output External alarm Remote station RB-8800/880 RB-880-W MAX 4 sets rinter IF+UT-80FK IF+UT-58E DMC I/F IF-880 RB-8800/880 RB-880-W ALARM UNIT IC-50 rinter /A Radio Battery 4 VDC AC/DC ower Supply Unit R-40 External Speaker SEM-Q Category of units Unit Antenna All other units 4 VDC Category Exposed to weather rotected from weather : Standard : Optional *: Option for FM-8800S/D-N ii

5 EQUIMENT LISTS Standard Supply Name Type Qty Code No. Remarks Transceiver Unit FM-8800D-E-A D: Duplex FM-8800D-E-N S: Simplex FM-8800D-F-A E: With handset FM-8800D-F-N HS-00 FM-8800S-E-A F: With microphone FM-8800S-E-N DM-00-F FM-8800S-F-A A: With IF-880 FM-8800S-F-N N: No IF-880 FM-8800S-R-A R: Russian version FM-8800S-R-N For E-type Handset HS-00, F Hanger F , Accessories* Others F F For F-type Microphone DM-00-F Junction Box IF-880 For A-type 4 Installation ower cable 05S97, C Materials* C Spare arts* S Standard Supply for VHF Console Name Type Qty Code No. Remarks VHF Console RC-8800-SN RC-8800-DN RC-8800-SA RC-8800-DA RC-8800-SB RC-8800-DB Installation Masteries* Accessories* C F F D: Duplex FM-8800D S: Simplex DM-8800S N: No printer A: With printer UT-80FK B: With printer UT-58E Handset HS-00 & Handset hanger F HS-00, F , Thermal paper T058-0CL *: See lists at the end of this manual. iii

6 EQUIMENT LISTS Optional Equipment Name Type Code No. Remarks Flush Mount Kit O Junction Box IF-880 W/ Screw 5x0 4 pcs. DMC Interface IF-880 No use for Russian version Remote Station Handset RB (W/.5 m Cable) RB (W/ m Cable) RB (W/.5 m Cable) RB F *, Handset HS-8800, Hanger W/DIST. button HG-8800 F05-055*, Handset HS-8800, Hanger HG-880 (W/ m Cable) RB-880-W-5 W/ HS-8800-W-5 HS W/.5 m Cable HS W/ m Cable HS-8800-W Waterproof HS W/ Cable.5 m HS W/ Cable.0 m HS-00-50S W/ Straight cable 5.0 m HS-6000FZ F HS-00-5 & Hanger HG For HS-8800 Handset Hanger HG For HS-8800 F For HS-00 A For HS-6000FZ Loudspeaker SEM-Q Dynamic Mic. Set O Handset HS-6000FZ5, Receptacle RDB-VHF(B), Hanger A-0 Carbon Mic. Set O Handset HS-6000FZ6, Receptacle RDB-VHF, Hanger A-0 Handset set O Handset HS-6000FZ, Receptacle RDB-VHF(B), Hanger A-0 Mic. Receptacle Box RBD-VHF (B) Microphone DM-00-F For transceiver unit only (not RB-8800), ** rinter -50 rinter Interface IF-8500 AC-DC ower Supply R-40 A Whip antenna FAB-5D, Mounting plate 4-007, Coax. Cable 5D-V 0m, Connector M--5 CS Whip antenna RA06, Antenna Material A Mounting plate RA5, Coax. Cable 05S904 5m A Whip antenna 96-, Mounting plate 487 A Whip antenna FAB-5D, Mounting plate 4-007, Connector M--7 CS *: See lists at the end of this manual **: Microphone DM-00-F can be connected to transceiver unit instead of handset HS-00. However, in this case, any remote station is disabled. iv

7 EQUIMENT LISTS Name Type Code No. Remarks A Whip antenna 50M-WVN, Coax. Cable 5D-V 0m, Connector M--5 CS Whip antenna FAB-5D, Mounting plate 4-007, A Antenna Material Coax. Cable 5D-V 0m, Connector M--5 & M--7 Whip antenna FAB-5D, A Mounting plate 4-007, Coax. Cable 5D-V 0m, Connector M--5 & M--7 05S009 *0M* m 05S009 *0M* m Signal Cable 05S009 *0M* m 05S009 *40M* m 05S009 *50M* m m Twisted Cable m CO-SEVV-SB-C m 0.x m m RC-8800-N-75BG - Without rinter VHF Console Kit RC-8800-A-75BG - With rinter UT-80FK RC-8800-B - With rinter UT-58E rinter A - W/ power cable Emergency lamp kit O For rack console, cable attached Cable 05S9509-L For handset extension Recording paper v

8 EQUIMENT LISTS This page is intentionally left blank. vi

9 . MOUNTING NOTICE Do not apply paint, anti-corrosive sealant or contact spray to coating or plastic parts of the equipment. Those items contain organic solvents that can damage coating and plastic parts, especially plastic connectors. Transceiver Unit General mounting considerations Determine the mounting location for the transceiver unit considering operator convenience, proximity to the power source and the ground location. Keep these and the following points in mind when selecting a mounting location. Locate the unit in a place free of water spray and water splash. Keep the unit out of direct sunlight because of heat that can build up inside the unit. Leave a little slack in cables to allow a service technician to move the radio from its usual location with the cables connected. This lets him make tuning and other adjustments on a live set. Do not install the unit where flammable gases are stored. Select a well-ventilated area. Ensure the mounting location is strong enough to support the weight of the unit (approx. 6 kg) under the condition of continued vibration normally encountered aboard the vessel. If necessary, reinforce the mounting area with a doubling plate or lining block. Leave sufficient space at the sides and rear of the unit for maintenance and service purposes and to provide for circulation of cooling air. See outlines drawings at the back of this manual. For flush mounting, select a location where the LCD can be easily viewed. The transceiver unit will affect a magnetic compass if placed too near the compass. Observe the compass safe distance to prevent deviation of a magnetic compass, referring to page i. Note: Take great care not to press the DISTRESS switch during the installation. If you accidentally press the switch, immediately turn off the equipment and contact appropriate authority by telephone. -

10 DISTRESS CANCEL ALM STO Keep pressed for 4 s in case of DISTRESS. The alert is transmitted with steady lighting. 4 IntCom GHI INTL 7 USA QRS * ABC TEST CH6 DEF RINT MNO DW WXYZ CALL SHIFT 0 HI/L0 # LOG MSG 5 8 JKL ACK SCAN TUV 6 9 DISTRESS ALM STO FILE MENU ENT * Keep pressed for 4 s in case of DISTRESS. The alert is transmitted with steady lighting. GHI QRS ABC JKL TUV # DEF MNO WXYZ DISTRESS CANCEL ALM STO Keep pressed for 4 s in case of DISTRESS. The alert is transmitted with steady lighting. 4 IntCom GHI INTL 7 USA QRS * ABC TEST CH6 DEF RINT MNO DW WXYZ CALL SHIFT 0 HI/L0 # LOG MSG 5 8 ACK JKL SCAN TUV 6 9 FILE MENU ENT. MOUNTING Overview of mounting methods Overhead Tabletop TEST CH6 4 IntCom 5 ACK 6 RINT FILE CANCEL 7 INTL USA 8 SCAN 9 DW MENU CALL SHIFT MSG 0 HI/L0 LOG ENT Flush Mount Bulkhead Overview of mounting methods -

11 DISTRESS CANCEL ALM STO DISTRESS 4 IntCom 5 ACK GHI JKL CANCEL INTL 7 USA 8 SCAN ALM STO QRS TUV * Keep pressed for 4 s in case of DISTRESS. The alert is transmitted with steady lighting. ABC TEST CH6 DEF 6 RINT MNO 9 DW WXYZ CALL SHIFT 0 HI/L0 # LOG MSG Keep pressed for 4 s in case of DISTRESS. The alert is transmitted with steady lighting. 4 IntCom GHI INTL 7 USA QRS * ACK JKL SCAN TUV RINT MNO DW WXYZ CALL SHIFT 0 HI/L0 # LOG MSG ABC TEST CH6 DEF FILE MENU ENT FILE MENU ENT. MOUNTING Mounting procedure for tabletop, overhead and bulkhead mounting. Using the hanger as a template, mark fixing holes in the mounting location.. Fix the hanger to the mounting location with self-tapping screws and washers (supplied). (For added support, use nuts, bolts and washers instead of self-tapping screws.). Screw the knob bolts with washers into the transceiver unit. 4. Set the transceiver unit to the hanger and tighten knob bolts All dimensions in millimeters. Leave sufficient space at the sides and rear of the unit to provide easy access for maintenance and service. Mounting dimensions for tabletop, overhead and bulkhead mounting -

12 . MOUNTING Mounting procedure for flush mount (option) Requires optional flush mount kit O05-0 (Code No ). repare a cutout in the mounting location whose dimensions are as shown in the figure below. Flush mount kit O05-0 Name Type Code No. Qty Mounting plate Self-tapping screw 5x Hex screw M8x #50 60 ± 80 ± 77 ± ± 0 ± ± 0.5 ilot holes (4 pcs.) VHF Antenna The antenna requirements -4 Mounting dimensions for flush mount Any good quality antenna meeting the requirements shown below may be used. A high-gain antenna is preferable. Frequency range: 55 to 64 MHz Impedance: olarization: Handling power: Quality: 50 ohms Vertical 0 W/ min Mounting considerations Able to withstand marine environment The antenna should be well separated from nearby antennas, masts, and other interfering objects. The higher the antenna is mounted above the horizon, the further the communications range. Mounting procedure The basic mounting procedure for antennas supplied by FURUNO is as follows, however consult appropriate outline drawing for details.. Fasten the antenna bracket to the stanchion.. Set the antenna to the antenna bracket and tighten bolts.. Screw the coaxial cable plug into the antenna.

13 . MOUNTING CH70 RX Antenna The antenna should be well separated from nearby antennas, masts, and other interfering objects. The mounting procedure is the same as that for the VHF antenna, however consult appropriate outline drawing for details. Handset Hanger The handset hanger can be mounted at the left side of the transceiver unit. The mounting location should provide easy access to front panel controls while operating the handset. Also, the length of the standard handset cable is 50 cm, so locate the handset hanger within 50 cm of the unit. (Longer cables are available optionally.) ower Supply (option) For Convention vessels, both AC and DC power must be fed to the FM-8800D/8800S, via an AC-DC power supply. When AC input fails, DC power is supplied. FURUNO can supply an AC-DC power supply unit, the R-40. Mounting considerations When selecting a mounting location, keep in mind the following points. Select a location which provides adequate ventilation. The location must be clean and dry. The mounting location must be able to support the weight of the unit (4.5 kg) under the continued conditions of vibration normally encountered aboard the vessel. If necessary, reinforce the mounting location. The R-40 will affect a magnetic compass if it is placed to near the compass. Observe the compass safe distance to prevent deviation of a magnetic compass, referring to page i. Mounting Refer to outline drawing. -5

14 . MOUNTING rinter (option) rinter -50 To mount the printer, refer to the printer outline drawing at the back of this manual.. Select a flat surface.. Fix the mounting base to the mounting location with four screws (supplied).. Lay the printer on the top of the mounting base and fasten it with the mounting fixtures (two at each side and one at rear). Mounting Fixture Mounting Fixture Mounting Dimensions 00 (H) x 96 (W) mm rinter Mounting of rinter -50 The printer is flush-mounted in a panel. Refer to the outline drawing at the back of this manual.. Make a cutout of 08(w) x 8(h) mm.. Set the printer and fix it with four self-tapping screws (4x6). rinter Interface (option) The printer interface IF-8500 is required for the printer -50 which is commonly used with the FM-8800D/S and other MF/HF radio communication equipment. To mount the unit, see the outline drawing at the back of this manual. External Loudspeaker (option) The external loudspeaker can be installed on a tabletop, the overhead or a bulkhead. Fasten the loudspeaker to the mounting location with self-tapping screws, or nuts, bolts and washers. For mounting dimensions, see the outline drawing at the back of this manual. -6

15 . MOUNTING Junction box IF-880/ DMC interface IF-880 Note: DMC interface IF-880 is not used for Russian version. To install the remote box RB-8800/RB-880, wing handset, etc., the junction box IF-880 is required. Install the junction box near the transceiver unit. Approx. m cable is preattached to the junction box to connect to the transceiver unit. To connect Furuno s distress message controller DMC-5, the DMC interface IF-880 (option) is required.. Open the cover.. Mount the unit with four self-tapping screws (5x0) Note: This plug is not fitted in IF-880. Fixing holes 5mm dia. Mounting the junction box/dmc interface -7

16 . MOUNTING Remote station RB-8800/RB-880 (option) Up to four remote stations can be connected in a daisy chain. Note: For the remote station RB-8800, there are two method of cable entry: bottom-side entry and rear-side entry. For rear-side entry, make one or two holes of more than mm diameter. For last station in the daisy chain, just one cable entry hole is needed.. Remove screws on the handset hanger (four for RB-8800, six for RB-880).. Remove upper chassis of the hanger.. Mount the base of the hanger to a bulkhead with self-tapping screws 4x0 (four for RB-8800), or 4x6 (two for RB-880). 4. After connecting cables, assemble the remote station. 5. For RB-8800, attach blind seals on the screws. Cable entry φ 77 Handset HS-8800 Screws 4 pcs. Attach blind seal on the screws. 0 0 Cover of handset hanger φ Handset hanger HG DISTRESS 40 ± 0.5 Nameplate Cable entry (Rear) VOLUME #50 40 ± ± φ4.5 Fixing holes Cable entry (Bottom) Remote station RB-8800 Hanger HG-880 (77) 57 Handset HS Cable entry #50 (08) φ, Cable entry Nameplate ± φ4.5 Fixing hole Hanger Hanger mounting base Remote station RB-880-8

17 . MOUNTING Outdoor mounting of waterproof-type remote station RB-880-W Remote station RB-880-W (with waterproof-type handset HS-8800-W) can be mounted outdoors if it is set in a waterproof box. The hanger should be coated as directed below with silicone sealant for waterproofing. Note : Be sure to use a waterproof box to mount the RB-880-W outdoors. The waterproofing category of the RB-880-W is IEC6059 I56, however this should be protected from the weather (IEC 60945). Note : Before sealing with silicone sealant (for waterproofing), do the termination setting (only for termination device, see page -7), connect cables and conduct the performance test. After sealing, do not open the handset hanger.. Fix the mounting base with self-tapping screws. Coat exposed part of these screws with silicone sealant.. Attach the cable from the transceiver unit or junction box. Coat cable around cable entrance with silicone sealant.. Fix the cover of the handset hanger. Coat junction between mounting base and cover with silicone sealant.. Coat all around the cable at cable entry.. Coat self-tapping screws.. Coat all around the junction. Note: Confirm that plastic washers are in screw holes before fixing cover. -9

18 . MOUNTING VHF console Install the rack console where the equipment can be easily operated, checked and serviced. Consult with shipyard personnel and ship's officer-in-charge to determine best location. The location must satisfy the following points: Select a location where controls can be easily operated. Select a location where shock and vibration are minimal. Locate the console away from water splash and rain. The temperature and humidity of the location should be both stable and moderate. Fixing. Ask shipyard personnel to tighten six M5 nuts or six M5 bolts to the fixing holes (on the wall), referring to the outline drawing at the back of this manual.. Detach the cover assembly from the console.. Hang VHF console on bolts. 4. Screw the console with the bolts or nuts tightly. 5. Attach the cover assembly to the console. Note: When you connect wires as soon as attaching console, refer to paragragh Attach the handset hanger with two screws. 7. To attach the optional emergency lamp, connect the cable to the terminal board, and then attach the lamp to the console. Refer to the interconnection diagram and out line drawing. (7) (7) 0 EMG-T EMERGENCY LAM HANDSET HANGER 70 ± (500) ± CABLE ENTRY (REAR) ± FIXING HOLES TERMINAL BOARD (66) #50-0

19 . CONNECTIONS Overview The figure below shows where to connect various equipment at the rear of the transceiver unit. ANT Connects antenna. Ground terminal. 4VDC Connects power cable. RINTER Connects printer -50. IEC66- (NMEA)/REMOTE Connects junction box IF-880. EXT S Connects external loudspeaker. CH70 RX ANT Connects DSC antenna here. FM-8800D/8800S, rear view Connection of ower Supply Convention vessels, 00/0 VAC ship s mains Convention vessels must supply both AC and DC power to the FM-8800D/8800S, via an AC-DC power supply unit. Both AC and DC are supplied by the AC-DC power supply unit, and when AC input fails DC power is activated. Connect the radio battery to the DC IN terminal on the R-40. Connect the AC ship s mains to the AC IN terminal on the R-40. Radio battery (4 VDC) Attach the connector supplied to the power cable and plug it into the 4VDC connector at the rear of the transceiver unit. Connect the wire ends to the radio battery line. -

20 . CONNECTIONS Connection of VHF Antenna The VHF antenna is connected to the transceiver unit with a 50 ohm coaxial cable, type 5D-V. Be sure to leave some slack in the cable for future service and maintenance. Lay the coaxial cable and attach an M-type plug to the cable (if necessary) as follows.. Remove the sheath by 0 mm.. Bare mm of the center conductor. Trim braided shield by 5 mm and tin.. Slide coupling ring onto cable. 4. Screw the plug assembly on the cable. 5. Solder plug assembly to braided shield through solder holes. Solder contact sleeve to conductor. 6. Screw coupling ring into plug assembly. 7. Screw the plug into the ANT connector at the rear of the transceiver unit. How to attach the M-type plug to the coaxial cable -

21 . CONNECTIONS Connection of DSC Antenna The DSC antenna is connected to the transceiver unit with a 50 ohm coaxial cable, type 5D-V. Attach an M-type plug to the cable (if necessary) as shown an page -. Screw the plug into the CH70 RX ANT connector at the rear of the transceiver unit. Connection of Handset Connect the handset cable to the HANDSET connector on the front panel. Grounding the Transceiver Unit Fasten a ground wire (local supply) between the GND terminal at the rear of the transceiver unit and ship s hull (or ground bus). Connecting the Junction Box The junction box is required to connect a remote station, wing handset, etc. The cable to be connected with the transceiver unit is prefitted on the junction box at the factory. For connection of other cables, see the interconnection diagram. Cable entry Clamp the cable with U-type cable clamps. Use one of these nuts for ground terminal between JB and ship's body. Cable clamp: Clamp shield part of the cables to ground cables. -

22 . CONNECTIONS Connecting the Remote Station without the Junction Box The remote station (or DMC Interface, Mic. Receptacle box, etc) can be connected directly to the transceiver unit, using the D-sub connector supplied as installation materials. Attach the connector to the cable as follows. Shield tape (metal) Fold back the armor, and then wind the shield tape along the edge of cable. Cable clamp Cable Connector XMA-70 & Housing case XMS-7 Attachment of connector When the handset HS-00 is not connected to the Transceiver unit When the handset HS-00 is not connected to the transceiver unit, i.e.,always the remoted handset is used, the following modification is necessary.. Dismount the cover of the transceiver unit by removing four screws at the rear panel and two screws at the side.. Dismount the bottom cover by removing seven screws. J5 CU board Shorten between # and # of J5. The handset line of the HANDSET port becomes always ON HOOK. 4. Assemble the unit. -4

23 . CONNECTIONS Connection of AC-DC ower Supply Unit R-40 The AC/DC power supply unit R-40 is shipped ready for connection to a 00-0 VAC ship s mains. If the ship s mains is 00 VAC-5 VAC, change the tap connection and terminal board connection as below. Attach a label supplied as accessories to the front panel according to the ship s mains. Ship s mains Tap connection Terminal board Label 00-0 VAC SEL 0 V Below (a) 00-0 VAC.-.7 A 50/60 Hz 00-5 VAC SEL 5 V Below (b) 00-5 VAC.-.6 A 50/60 Hz Remove screw and cover. Cover Front panel (a) 00-0 VAC Black Grey J4 Relay Coil (b) Terminal board 00-5 VAC Black Grey SEL 5V SEL 0V Heat sink Tap connection (ull out to disconnect.) Front panel Attach appropriate label. AC FAIL:Connect to Alarm system. Output Setting: Normal Open Set plug to & pins of J4 (Factory setting) Normal Close Set plug to & pins of J4 AC ower Switch (When connecting DC input, note that the DC power is supplied even though this switch is turned off.) Note: The DC output load must be less than 8A. -5

24 . CONNECTIONS rotective earth Connect IV-.0sq wire between ship s superstructure and the ground terminal on the R-40. CAUTION Attach protective earth securely to the ship's body. The protective earth (grounding) is required for the AC/DC power supply unit to prevent electrical shock. Attach a label here. GND terminal R-40 Front panel -6

25 . CONNECTIONS Jumper Setting for Termination Note: DMC interface is not used for Russian version. It is necessary, for termination, to change the jumper setting for remote station or DMC interface. Open the unit(s) terminated and change the jumper plugs J and J to ON position (#-#). (Default setting is OFF position.) Transceiver Unit Junction Box Remote Station Remote Station Remote Station Remote Station DMC I/F Remote Station Terminated Unit Note that up to four remote stations can be connected. LINE TERMINATION J ON RS-485 TERMINATION J ON J DISTRESS TB Set to ON (#-) for termination. VOLUME TB Remote station RB-8800 Cable entry TB TB J φ Fixing hole RS-485 TERMINATION J J ON OFF ON OFF LINE TERMINATION Set to ON (#-) for termination. Remote station RB-880-7

26 . CONNECTIONS Remove four screws to open the unit. Set jumper plug to ON (#-) ON J4 RS-485 TERMINATION TB DMC Interface IF-880-8

27 . CONNECTIONS.0 Wire connection of VHF console. Remove the cover assembly and printer assembly (or concealing lid) form the console. For the printer assembly, remove the cables connected at the Transceiver Unit and the terminal board. Cover assembly Binding screw F M4X0 8 places Binding screw F M4X0 4 places rinter assembly or Concealing lid Console Terminal board. Connect the power cable from the ship to the terminal block (+) and (-). Terminal Board Wiring. Wiring conductor 90mm. Wiring )Insert a screwdriver which blade edge is.5 X 0.5mm to the square hole. )ress the screwdriver to arrow direction to open the spring in the round hole. )Insert the wire to the round hole. 4)Remove the screwdriver. ower cable from the ship - Square hole Round hole Terminal board. Connect the ground wire from ship to each ground terminal for the transceiver unit and the junction box. 4. Connect cables from external equipments to the junction box. 5. Fix the printer assembly (or concealing lid) and the cover assembly. -9

28 . CONNECTIONS Emergency Lamp Kit (Optional). Remove the two screws from the position to place the lamp on the left or right side of the rack. Remove the two screws. Insert the emergency lamp base into the fixing plate included with the kit. Affix the fixing plate to the rack using the two screws from step one as shown. Mounting plate U p w Emergency lamp base a r d s Cable entry. Insert the cable from the emergency lamp base into the cable entry of the rack. Connect the cable to terminal board, referring to the wiring diagram at the back of this manual. 4. Insert the emergency lamp connector into the lamp base. -0

29 . ASSEMBLING CONSOLE KIT A VHF console kit is required to mount the Transceiver Unit in the field. There are two types as shown below. VHF console kit Type Code No. Remarks RC-8800-N-75BG Without printer RC-8800-A-75BG With printer Assembling the Console Kit. Remove the cover assembly, the panel assembly and the printer assembly (or concealing lid) from the console. For the printer assembly, remove the cable connected to the terminal board. Cover assembly Binding screw F M4X0 8 places Binding screw F M4X0 4 places rinter assembly (or Concealing lid # # Remove screws( )and detach the panel assembly. Console anel assembly -

30 . Fix the panel assembly to the Transceiver Unit with binding screws (use original binding screws of the Transceiver Unit). Refer to the figure below.. Screw in hex bolts M8x6 and flat washers loosely at both sides of the Transceiver Unit. anel assembly Binding screw M4 places (Use the original screws of the Transceiver Unit.) Washer M8 places Hex bolt M8X6 places (faster loosely) 4. Set the Transceiver Unit to the console, remove the grommets from the console and fix the Transceiver Unit with hex bolts using the holes formerly occupied by the grommets. Mounting of the Transceiver Unit Insert console upside down. Hex head screws Close the hole with grommets lastly. Connecter Connecter Transceiver Unit Mounting plate Flat washer Fix Mounting late between washers. 5. Connect connector from the fuse to the power connector derived from the Transceiver Unit. -

31 6. Replace the cable attached to junction box with the cable (55 cm, 7-pin D sub) supplied with the console kit. A Replace the original cable with the cable assembly DSUB7M-HX-L550. Junction box (without cover) H Connector 0 H Connector J J J H Connector 4 Crimp-on lug A View 7. Connect the cable (7-pin D sub) attached to the junction box to the Transceiver Unit and then mount the junction box on the console. Binding screw F M4X8 4 places Cover Screw B M4X04 places Mounting plate -

32 Grommets places Junction box 8. For the console w/printer, connect the printer cable for data transmission to the RINTER port of the Transceiver Unit and fix the power cable to the terminal board as before. Then, fix the printer assembly to the console. For no printer, fasten the concealing lid to the console. rinter rinter cable W/ rinter J Insert the mounting plate for printer to the catch of the console View 9. Fasten the cover assembly. NOTE: If the console assembly is to be mounted on the hull, refer to paragraghs -9 and

33 ACKING LIST FM-8800(S/D)-(J/E/F)-HS-N 05EC-X / NAME OUTLINE DESCRITION/CODE Q'TY NAME OUTLINE DESCRITION/CODE Q'TY ユニット UNIT 図書 DOCUMENT 送受信機 TRANSCEIVER UNIT FM-8800S/D ** 取扱説明書 OERATOR'S MANUAL OM*-5640-* * 予備品 SARE ARTS S 操作要領書 OS*-5640-* 予備品 OERATOR'S GUIDE S * ** SARE ARTS 装備要領書 IM*-5640-* 付属品 ACCESSORIES F INSTALLATION MANUAL * ** ハント セット HS-00-5 遭難警報フロ -(VHF/MF)) *5-000-* HANDSET VHF/MF DISTRESS ALERT FLOW * ** ハント セットハンカ ー組品 F 遭難通信要領書 ( 和 / 英 ) TIC-5640-* BRACKET FOR HANDSET DISTRESS ROCEDURE * 付属品 F ACCESSORIES ** 工事材料 INSTALLATION MATERIALS C ケーフ ル組品 CABLE ASSY. 工事材料 INSTALLATION MATERIALS 05S C コ - ト 番号末尾の [**] は 選択品の代表型式 / コート を表します CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF RERESENTATIVE MATERIAL. 型式 / コート 番号が 段の場合 下段より上段に代わる過渡期品であり どちらかが入っています なお 品質は変わりません ( 略図の寸法は 参考値です DIMENSIONS IN DRAWING FOR REFERENCE ONLY.) TWO TYES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER RODUCT MAY BE SHIED IN LACE OF THE UER RODUCT. QUALITY IS THE SAME. 05EC-X-985

34 ACKING LIST FM-8800(S/D)-(J/E/F)-HS-A/(-HK) 05EC-X / NAME OUTLINE DESCRITION/CODE Q'TY ユニット UNIT 送受信機 TRANSCEIVER UNIT 接続箱 JUNCTION BOX 予備品 SARE ARTS FM-8800S/D IF ** 工事材料 NAME OUTLINE DESCRITION/CODE Q'TY INSTALLATION MATERIALS C 工事材料 INSTALLATION MATERIALS C 工事材料 INSTALLATION MATERIALS 図書 DOCUMENT C 予備品 SARE ARTS S 付属品 ACCESSORIES F ハント セット HANDSET ハント セットハンカ ー組品 BRACKET FOR HANDSET 付属品 ACCESSORIES HS F F 工事材料 INSTALLATION MATERIALS C ケーフ ル組品 CABLE ASSY. 05S 取扱説明書 OERATOR'S MANUAL 操作要領書 OERATOR'S GUIDE 装備要領書 INSTALLATION MANUAL 遭難警報フロ -(VHF/MF)) VHF/MF DISTRESS ALERT FLOW 遭難通信要領書 ( 和 / 英 ) DISTRESS ROCEDURE OM*-5640-* * OS*-5640-* * IM*-5640-* * *5-000-* * TIC-5640-* * ** ** ** ** コ - ト 番号末尾の [**] は 選択品の代表コート を表します CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF RERESENTATIVE MATERIAL. 型式 / コート 番号が 段の場合 下段より上段に代わる過渡期品であり どちらかが入っています なお 品質は変わりません ( 略図の寸法は 参考値です DIMENSIONS IN DRAWING FOR REFERENCE ONLY.) TWO TYES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER RODUCT MAY BE SHIED IN LACE OF THE UER RODUCT. QUALITY IS THE SAME. 05EC-X-9856

35 ACKING LIST FM-8800(S/D)-(E/F)-MIC-N 05EC-X / NAME OUTLINE DESCRITION/CODE Q'TY ユニット UNIT 送受信機 TRANSCEIVER UNIT 予備品 SARE ARTS 予備品 SARE ARTS FM-8800S/D S 付属品 ACCESSORIES F ** 装備要領書 ( 英 ) NAME OUTLINE DESCRITION/CODE Q'TY INSTALLATION MANUAL 遭難警報フロ -(VHF/MF)( 英 ) DISTRESS ALERT CHART(VHFMF) 遭難通信要領書 ( 和 / 英 ) DISTRESS ROCEDURE IME-5640-* * E5-000-* * TIC-5640-* * マイクロフォン箱詰品 MICROHONE DM-00-F 工事材料 INSTALLATION MATERIALS C ケーフ ル組品 CABLE ASSY. 工事材料 INSTALLATION MATERIALS 図書 DOCUMENT 05S C 取扱説明書 ( 英 ) OERATOR'S MANUAL 操作要領書 ( 英 ) OERATOR'S GUIDE OME-5640-* * OSE-5640-* * コ - ト 番号末尾の [**] は 選択品の代表コート を表します CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF RERESENTATIVE MATERIAL. 型式 / コート 番号が 段の場合 下段より上段に代わる過渡期品であり どちらかが入っています なお 品質は変わりません ( 略図の寸法は 参考値です DIMENSIONS IN DRAWING FOR REFERENCE ONLY.) TWO TYES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER RODUCT MAY BE SHIED IN LACE OF THE UER RODUCT. QUALITY IS THE SAME. 05EC-X-9858

36 ACKING LIST FM-8800(S/D)-(E/F)-MIC-A 05EC-X / NAME OUTLINE DESCRITION/CODE Q'TY ユニット UNIT NAME OUTLINE DESCRITION/CODE Q'TY 図書 DOCUMENT 接続箱 JUNCTION BOX 送受信機 TRANSCEIVER UNIT 予備品 SARE ARTS 予備品 SARE ARTS IF FM-8800S/D S 付属品 ACCESSORIES F マイクロフォン箱詰品 MICROHONE DM-00-F 工事材料 INSTALLATION MATERIALS C ** 取扱説明書 ( 英 ) OERATOR'S MANUAL 操作要領書 ( 英 ) OERATOR'S GUIDE 装備要領書 ( 英 ) INSTALLATION MANUAL 遭難警報フロ -(VHF/MF)( 英 ) DISTRESS ALERT CHART(VHFMF) 遭難通信要領書 ( 和 / 英 ) DISTRESS ROCEDURE OME-5640-* * OSE-5640-* * IME-5640-* * E5-000-* * TIC-5640-* * ケーフ ル組品 CABLE ASSY. 工事材料 INSTALLATION MATERIALS 工事材料 INSTALLATION MATERIALS 05S C 工事材料 INSTALLATION MATERIALS C コ - ト 番号末尾の [**] は 選択品の代表コート を表します CODE NUMBER ENDING WITH "**" INDICATES THE CODE NUMBER OF RERESENTATIVE MATERIAL. 型式 / コート 番号が 段の場合 下段より上段に代わる過渡期品であり どちらかが入っています なお 品質は変わりません ( 略図の寸法は 参考値です DIMENSIONS IN DRAWING FOR REFERENCE ONLY.) TWO TYES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER RODUCT MAY BE SHIED IN LACE OF THE UER RODUCT. QUALITY IS THE SAME. 05EC-X-9859

37 A-5 A-6

38 A-8 A-7

39 A-9 A-0

40 A- A- Used only Japan

41 A- A-4

42 A-5

43 ACKING LIST FM-8800S-R-HS-N 05EC-X / NAME OUTLINE DESCRITION/CODE Q'TY NAME OUTLINE DESCRITION/CODE Q'TY ユニット UNIT 図書 DOCUMENT 送受信機 TRANSCEIVER UNIT FM-8800S-R 取扱説明書 ( 英 ) OERATOR'S MANUAL OME-564-* * 予備品 SARE ARTS S 操作要領書 ( 英 ) OSE-5640-* 予備品 OERATOR'S GUIDE S * SARE ARTS 装備要領書 ( 英 ) IME-5640-* 付属品 ACCESSORIES F INSTALLATION MANUAL * ハント セット HS-00-5 遭難警報フロ -(VHF/MF)( 英 ) E5-000-* HANDSET DISTRESS ALERT CHART(VHFMF) * ハント セットハンカ ー組品 F 遭難通信要領書 ( 和 / 英 ) TIC-5640-* BRACKET FOR HANDSET DISTRESS ROCEDURE * 付属品 F ACCESSORIES 工事材料 INSTALLATION MATERIALS C ケーフ ル組品 CABLE ASSY. 工事材料 INSTALLATION MATERIALS 05S C 型式 / コート 番号が 段の場合 下段より上段に代わる過渡期品であり どちらかが入っています なお 品質は変わりません ( 略図の寸法は 参考値です DIMENSIONS IN DRAWING FOR REFERENCE ONLY.) TWO TYES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER RODUCT MAY BE SHIED IN LACE OF THE UER RODUCT. QUALITY IS THE SAME. 05EC-X-9864

44 ACKING LIST FM-8800S-R-MIC-N 05EC-X / NAME OUTLINE DESCRITION/CODE Q'TY ユニット UNIT 送受信機 TRANSCEIVER UNIT FM-8800S-R 予備品 SARE ARTS S 予備品 SARE ARTS S 付属品 ACCESSORIES F 装備要領書 ( 英 ) NAME OUTLINE DESCRITION/CODE Q'TY INSTALLATION MANUAL 遭難警報フロ -(VHF/MF)( 英 ) DISTRESS ALERT CHART(VHFMF) 遭難通信要領書 ( 和 / 英 ) DISTRESS ROCEDURE IME-5640-* * E5-000-* * TIC-5640-* * マイクロフォン箱詰品 MICROHONE DM-00-F 工事材料 INSTALLATION MATERIALS C ケーフ ル組品 CABLE ASSY. 工事材料 INSTALLATION MATERIALS 図書 DOCUMENT 05S C 取扱説明書 OERATOR'S MANUAL 操作要領書 ( 英 ) OERATOR'S GUIDE OME-564-* * OSE-5640-* * 型式 / コート 番号が 段の場合 下段より上段に代わる過渡期品であり どちらかが入っています なお 品質は変わりません ( 略図の寸法は 参考値です DIMENSIONS IN DRAWING FOR REFERENCE ONLY.) TWO TYES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER RODUCT MAY BE SHIED IN LACE OF THE UER RODUCT. QUALITY IS THE SAME. 05EC-X-9865

45 ACKING LIST FM-8800S-R-HS-A 05EC-X / NAME OUTLINE DESCRITION/CODE Q'TY ユニット UNIT 接続箱 JUNCTION BOX 送受信機 TRANSCEIVER UNIT IF FM-8800S-R 工事材料 NAME OUTLINE DESCRITION/CODE Q'TY INSTALLATION MATERIALS C 工事材料 INSTALLATION MATERIALS C 工事材料 INSTALLATION MATERIALS C 予備品 SARE ARTS 図書 DOCUMENT 予備品 SARE ARTS S 取扱説明書 ( 英 ) OERATOR'S MANUAL OME-564-* * 付属品 ACCESSORIES F 操作要領書 ( 英 ) OSE-5640-* ハント セット OERATOR'S GUIDE HS * HANDSET 装備要領書 ( 英 ) IME-5640-* ハント セットハンカ ー組品 INSTALLATION MANUAL F * BRACKET FOR HANDSET 遭難警報フロ -(VHF/MF)( 英 ) E5-000-* 付属品 DISTRESS ALERT F CHART(VHFMF) * ACCESSORIES 遭難通信要領書 ( 和 / 英 ) TIC-5640-* 工事材料 INSTALLATION MATERIALS C DISTRESS ROCEDURE * ケーフ ル組品 05S97- CABLE ASSY 型式 / コート 番号が 段の場合 下段より上段に代わる過渡期品であり どちらかが入っています なお 品質は変わりません ( 略図の寸法は 参考値です DIMENSIONS IN DRAWING FOR REFERENCE ONLY.) TWO TYES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER RODUCT MAY BE SHIED IN LACE OF THE UER RODUCT. QUALITY IS THE SAME. 05EC-X-9866

46 ACKING LIST FM-8800S-R-MIC-A 05EC-X / NAME OUTLINE DESCRITION/CODE Q'TY ユニット UNIT NAME OUTLINE DESCRITION/CODE Q'TY 図書 DOCUMENT 接続箱 JUNCTION BOX 送受信機 TRANSCEIVER UNIT IF FM-8800S-R 予備品 SARE ARTS S 予備品 SARE ARTS S 付属品 ACCESSORIES F マイクロフォン箱詰品 MICROHONE DM-00-F 工事材料 INSTALLATION MATERIALS C 取扱説明書 ( 英 ) OERATOR'S MANUAL 操作要領書 ( 英 ) OERATOR'S GUIDE 装備要領書 ( 英 ) INSTALLATION MANUAL 遭難警報フロ -(VHF/MF)( 英 ) DISTRESS ALERT CHART(VHFMF) 遭難通信要領書 ( 和 / 英 ) DISTRESS ROCEDURE OME-564-* * OSE-5640-* * IME-5640-* * E5-000-* * TIC-5640-* * ケーフ ル組品 CABLE ASSY. 工事材料 INSTALLATION MATERIALS 05S C 工事材料 INSTALLATION MATERIALS C 工事材料 INSTALLATION MATERIALS C 型式 / コート 番号が 段の場合 下段より上段に代わる過渡期品であり どちらかが入っています なお 品質は変わりません ( 略図の寸法は 参考値です DIMENSIONS IN DRAWING FOR REFERENCE ONLY.) TWO TYES AND CODES MAY BE LISTED FOR AN ITEM. THE LOWER RODUCT MAY BE SHIED IN LACE OF THE UER RODUCT. QUALITY IS THE SAME. 05EC-X-9867

47

48

49

50

51

52

53 Y. Hatai

54 Y. Hatai

55

56

57

58

59

60

61

62

63

64

65

66

67

68 4 5 6 A B C 4VDC 00-5/ 00-0VAC φ,50/60hz 4VDC 4VDC 4VDC T/R 用アンテナ ANTENNA FOR T/R * CH70 WR 用アンテナ * ANTENNA FOR CH70 WR 05S97,m DYC-.5 * AC DYC-4 * VCTF0.75xC,5m (6S0084) ハンドセット HANDSET HS-00 外部スピーカ EXT. SEAKER SEM-Q * DC + IN AC/DC OUT - 電源ユニット + AC/DC OWER DC SULY UNIT - IN R-40 保護アース E * IV-sq. RMBE-S RED BLK WHT アカクロシロ FM4-S VCTF0.75xC,m シロ WHT (05S044) クロ BLK * RG-0/UY * RG-0/UY 5A.8m J 4V+ 0V GND または (+) (-) ANT J CH70 RX ANT J 送受信機 TRANSCEIVER UNIT FM-8800D/S HANDSET S.GND TT SW-N MIC-H MIC-C HS S-H HOOK SW-N +5V F.GND φ.5 SKR S-H S-C RED BLK 4VDC(+) 4VDC(-) 7JE-50 RINTER -0(D8C) 57FE-060-0N(D8) OR M--7 M--7 6S084,m ~ 5 6 プリンタ RINTER -50 ~ 6 * プリンタ RINTER * -8800A IEC66-(NMEA)/REMOTE +5VDC +5VDC +5VDC +5VDC NC NC TXD-H TXD-C RXD-H RXD-C EXT.ALM-N 0V W_MIC-H W_MIC-C 4 W_S-H 5 W_S-C 6 W_TT-N 7 0V 8 0V 9 0V 0 0V 0V VDR AF-H VDR AF-C 4 DATA-A 5 DATA-B 6 LINE OUT-H 7 LINE OUT-C 8 LINE IN-H 9 LINE IN-C 0 W_MIC-H W_MIC-C W_S-H W_S-C 4 W_TT-N 5 0V 6 F.GND 7 GND * IV-.5sq. * IV-sq. XMA-70 5m 接続箱 JUNCTION BOX IF-880 TXD-H J TXD-C RXD-H RXD-C F.GND 4 EXT.ALM-N 5 *6 0V 6 F.GND 7 W_MIC-H 8 W_MIC-C 9 W_S-H 0 W_S-C J W_TT-N 0V F.GND 4 W_MIC-H 5 W_MIC-C 6 W_S-H 7 W_S-C 8 W_TT-N 9 0V 0 F.GND VDR AF-H J VDR AF-C NOT USED_ NOT USED_ F.GND VDC 6 0V 7 DATA-A 8 DATA-B 9 LINE IN-H 0 LINE IN-C LINE OUT-H LINE OUT-C F.GND 4 NC VDC 8 0V 9 DATA-A 40 DATA-B 4 LINE IN-H 4 LINE IN-C 4 LINE OUT-H 44 LINE OUT-C 45 F.GND 46 NC 47 NC 48 * IV-.5sq. *4 *4 *4 *4 *4 TTYCS-,MAX.0m * * CO-0.x5,MAX.0m アカ RED キ YEL クロ BLK キ YEL シロ WHT キ YEL * CO-0.x5,MAX.0m アカ RED キ YEL クロ BLK キ YEL シロ WHT キ YEL TTYCS-4(*) OR CO-0.x (*) * TTYCS-,MAX.0m 05S009 * 05S009 * 外部アラーム EXTERNAL ALARM TB マイクレセプタクル ボックス MIC RECETACLE BOX 4 4 RBD-VHF(B) * 5 6 VDR 終端まで最長 50m TOTAL 50m OR LESS TO TERMINATE シロ ( 太 ) WHT[B] TB TB TB TB シロ ( 太 ) WHT[B] クロ ( 太 ) BLK[B] リモートステーション クロ ( 太 ) BLK[B] リモートステーション REMOTE STATION REMOTE STATION ミドリ GRN RB-8800/880/880W ミドリ GRN RB-8800/880/880W アオ BLU 4 <No.> * * 4 アオ BLU 4 <No.> * * アカ RED 5 LINE IN-H 5 アカ RED 5 チャ BRN 6 LINE IN-C 6 チャ BRN 6 キ YEL 7 LINE OUT-H 7 キ YEL 7 ダイ ORG 8 LINE OUT-C 8 ダイ ORG 8 SHIELD G SHIELD G 終端まで最長 50m TOTAL 50m OR LESS TO TERMINATE 05S009 シロ ( 太 ) クロ ( 太 ) ミドリアオアカチャキダイ SHIELD 航法装置 / プロッタ NAVIGATOR/LOTTER TB マイクレセプタクル ボックス MIC RECETACLE BOX 4 RBD-VHF(B) * WHT[B] BLK[B] GRN BLU RED BRN YEL ORG ハンドセット HS-8800/8800W DMC I/F IF-880 * F.GND NC HANDSET * 0 F.GND TXD-H 0 TXD-C RXD-H RXD-C F.GND 4 Wing Mic ハンドセット HANDSET * HS-6000FZ- HS-6000FZ-5 Wing Mic ハンドセット HANDSET * HS-6000FZ- HS-6000FZ-5 * CO-0.x,MAX.0m 05S009 * シロ ( 太 ) クロ ( 太 ) ミドリアオアカチャキダイ SHIELD WHT[B] BLK[B] GRN BLU RED BRN YEL ORG ハンドセット HS-8800/8800W TB リモートステーション REMOTE STATION RB-8800/880/880W * TB/TB TXD-H TXD-C RXD-H RXD-C F.GND G HANDSET * 0 遭難警報装置 DISTRESS MESSAGE CONTROLLER DMC-5 *5 リモートステーション REMOTE STATION RB-8800/880/880W <No./No.4> ハンドセット HANDSET * HS-8800/8800W *5 リモートステーション REMOTE STATION RB-8800/880/880W D 注記 NOTE *) 造船所手配 *. SHIYARD SULY *) オプション *. OTION *) 最大 4 台まで接続可能 *. MAX. 4 SETS AVAILABLE *4) ケーブルクランプで接地 *4. GROUND THROUGH CABLE CLAM. *5) 終端ユニットは内部のジャンパー (J,J) をONにする *5. CONNECT JUMERS (J & J) ON TERMINATED REMOTE STATION. *6) ノーマルクローズ フローティング 最大 80mA 耐圧 50V *6. NORMAL CLOSE, FLOATING, MAX80mA, WITHSTAND VOLTAGE 50V. CO-0.x: CO-SEVV-SB-C 0.x,φ0.5 CO-0.x5: CO-SEVV-SB-C 0.x5,φ.5 DRAWN 6/Jan/0 CHECKED 6/Jan/0 AROVED SCALE DWG No. T.YAMASAKI T.TAKENO MASS C564-C0- N kg TITLE 名称 NAME FM-8800D/S 国際 VHF 無線電話装置相互結線図 VHF RADIOTELEHONE INTERCONNECTION DIAGRAM FURUNO ELECTRIC CO., LTD.

69 4 5 6 A B C 4VDC 00-5/ 00-0VAC φ,50/60hz 4VDC 4VDC VCTF0.75xC,5m (6S0084) T/R 用アンテナ ANTENNA FOR T/R * CH70 WR 用アンテナ * ANTENNA FOR CH70 WR 05S97,m DYC-.5 * AC DYC-4 * RMBE-S アカ RED クロ BLK シロ WHT ハンドセット HANDSET HS-00 外部スピーカ EXT. SEAKER SEM-Q * DC + IN AC/DC OUT - 電源ユニット + AC/DC OWER DC SULY UNIT - IN R-40 保護アース E * IV-sq. J 4V+ 0V GND 57FE-060-0N(D8) * RG-0/UY * RG-0/UY.8m 5A M--7 M--7 ANT J CH70 RX ANT J 送受信機 TRANSCEIVER UNIT FM-8800D/S HANDSET S.GND TT SW-N MIC-H MIC-C HS S-H HOOK SW-N +5V F.GND φ.5 SKR S-H S-C RED BLK 7JE-50 RINTER 6S084,m -0(D8C) ~ 6 プリンタ RINTER -50 * 5 4VDC(+) 4VDC(-) IEC66-(NMEA)/REMOTE GND +5VDC +5VDC +5VDC NC NC TXD-H TXD-C RXD-H RXD-C 0V 0V 0V 0V +5VDC 0V DATA-A DATA-B LINE OUT-H LINE OUT-C LINE IN-H LINE IN-C EXT.ALM-N *5 0V W_MIC-H W_MIC-C W_S-H W_S-C W_TT-N VDR AF-H VDR AF-C 4 W_MIC-H W_MIC-C W_S-H W_S-C W_TT-N 0V F.GND * IV-sq XMA-70 TTYCS-4(*) OR CO-0.x (*) * CO-0.x5,MAX.0m アカ RED キ YEL クロ BLK キ YEL シロ WHT キ YEL * TTYCS-,MAX.0m * TTYCS-,MAX.0m 05S009 * * CO-0.x5,MAX.0m アカ RED キ YEL クロ BLK キ YEL シロ WHT キ YEL シロ ( 太 ) WHT[B] クロ ( 太 ) BLK[B] ミドリ GRN アオ BLU アカ RED チャ BRN キ YEL ダイ ORG SHIELD 航法装置 / プロッタ NAVIGATOR/LOTTER 外部アラーム EXTERNAL ALARM VDR 終端まで最長 50m TOTAL 50m OR LESS TO TERMINATE TB マイクレセプタクル ボックス MIC RECETACLE BOX 4 4 RBD-VHF(B) * DMC I/F IF-880 * F.GND NC TB マイクレセプタクル ボックス MIC RECETACLE BOX 4 RBD-VHF(B) * TXD-H 0 TXD-C RXD-H RXD-C F.GND 4 ハンドセット HANDSET * HS-6000FZ- HS-6000FZ-5 Wing Mic * CO-0.x,MAX.0m ハンドセット HANDSET * HS-6000FZ- HS-6000FZ-5 Wing Mic 4 5 TB/TB TXD-H TXD-C RXD-H RXD-C F.GND 遭難警報装置 DISTRESS MESSAGE CONTROLLER DMC-5 4VDC VCTF0.75xC,m (05S044) FM4-S シロ WHT クロ BLK または (+) (-) OR ~ 6 プリンタ RINTER * -8800A * IV-.5sq. D 注記 *) 造船所手配 *) オプション *) 最大 4 台まで接続可能 *4) ケーブルクランプで接地 *5) ノーマルクローズ フローティング 最大 80mA 耐圧 50V NOTE *. SHIYARD SULY *. OTION *. MAX. 4 SETS AVAILABLE *4. GROUND THROUGH CABLE CLAM. *5. NORMAL CLOSE, FLOATING, MAX80mA, WITHSTAND VOLTAGE 50V. CO-0.x: CO-SEVV-SB-C 0.x,φ0.5 CO-0.x5: CO-SEVV-SB-C 0.x5,φ.5 DRAWN 6/Jan/0 CHECKED 6/Jan/0 AROVED SCALE DWG No. T.YAMASAKI T.TAKENO MASS C564-C0- F kg TITLE 名称 NAME FM-8800D/S 国際 VHF 無線電話装置 ( 接続箱なし ) 相互結線図 VHF RADIOTELEHONE (W/O JUNCTION BOX) INTERCONNECTION DIAGRAM FURUNO ELECTRIC CO., LTD.

70 4 5 6 A B C T/R 用アンテナ ANTENNA FOR T/R * CH70 WR 用アンテナ * ANTENNA FOR CH70 WR ハンドセット HANDSET HS-00 外部スピーカ EXT. SEAKER SEM-Q * 4VDC * DYC-.5 非常灯 EMERGENCY LAM EMG-T *.8m * IV-sq. * RG-0/UY * RG-0/UY TB CB 5A RED BLK S RACK CONSOLE M--7 M ANT J CH70 RX ANT J 送受信機 TRANSCEIVER UNIT FM-8800D/S HANDSET S.GND TT SW-N MIC-H MIC-C HS S-H HOOK SW-N +5V F.GND φ.5 SKR S-H S-C J7 GND 4VDC(+) 4VDC(-) J 4V 0V IEC66-(NMEA)/REMOTE RINTER J +5VDC +5VDC +5VDC +5VDC NC NC TXD-H TXD-C RXD-H RXD-C EXT.ALM-N 0V W_MIC-H W_MIC-C 4 W_S-H 5 W_S-C 6 W_TT-N 7 0V 8 0V 9 0V 0 0V 0V VDR AF-H VDR AF-C 4 DATA-A 5 DATA-B 6 LINE OUT-H 7 LINE OUT-C 8 LINE IN-H 9 LINE IN-C 0 W_MIC-H W_MIC-C W_S-H W_S-C 4 W_TT-N 5 0V 6 F.GND 7 ~ I/F J6 5 6 ~ プリンタ RINTER UT-58E J 40 ~ 40 XMA-70 接続箱 JUNCTION BOX IF-880 TXD-H J TXD-C RXD-H RXD-C F.GND 4 EXT.ALM-N 5 *6 0V 6 F.GND 7 W_MIC-H 8 W_MIC-C 9 W_S-H 0 W_S-C J W_TT-N 0V F.GND 4 W_MIC-H 5 W_MIC-C 6 W_S-H 7 W_S-C 8 W_TT-N 9 0V 0 F.GND VDR AF-H J VDR AF-C NOT USED_ NOT USED_ F.GND VDC 6 0V 7 DATA-A 8 DATA-B 9 LINE IN-H 0 LINE IN-C LINE OUT-H LINE OUT-C F.GND 4 NC VDC 8 0V 9 DATA-A 40 DATA-B 4 LINE IN-H 4 LINE IN-C 4 LINE OUT-H 44 LINE OUT-C 45 F.GND 46 NC 47 NC 48 *4 *4 *4 *4 *4 TTYCS-,MAX.0m * * CO-0.x5,MAX.0m アカ RED キ YEL クロ BLK キ YEL シロ WHT キ YEL * CO-0.x5,MAX.0m アカ RED キ YEL クロ BLK キ YEL シロ WHT キ YEL TTYCS-4(*) OR CO-0.x (*) TTYCS-,MAX.0m * VDR 外部アラーム EXTERNAL ALARM 終端まで最長 50m TOTAL 50m OR LESS TO TERMINATE シロ ( 太 ) WHT[B] クロ ( 太 ) BLK[B] ミドリ GRN アオ BLU アカ RED チャ BRN キ YEL ダイ ORG SHIELD TBマイクレセプタクル ボックス MIC RECETACLE BOX 4 4 RBD-VHF(B) * 5 6 TBマイクレセプタクル ボックス MIC RECETACLE BOX 4 4 RBD-VHF(B) * 5 6 ハンドセット HS-8800/8800W DMC I/F IF-880 * F.GND NC F.GND TXD-H 0 TXD-C RXD-H RXD-C F.GND 4 Wing Mic ハンドセット HANDSET * HS-6000FZ- HS-6000FZ-5 Wing Mic ハンドセット HANDSET * HS-6000FZ- HS-6000FZ-5 * CO-0.x,MAX.0m ハンドセット HS-8800/8800W 終端まで最長 50m TOTAL 50m OR LESS TO TERMINATE TB TB 05S009 TB TB 05S009 *5 シロ ( 太 ) WHT[B] シロ ( 太 ) WHT[B] リモートステーション クロ ( 太 ) BLK[B] リモートステーション クロ ( 太 ) BLK[B] リモートステーション REMOTE STATION REMOTE STATION REMOTE STATION ミドリ GRN RB-8800/880/880W ミドリ GRN <No./No.4> アオ BLU 4 4 アオ BLU 4 4 RB-8800/880/880W <No.> * * RB-8800/880/880W <No.> * * キ YEL 7 LINE OUT-H 7 キ YEL 7 7 アカダイ RED ORG 5 8 LINE IN-H LINE OUT-C 5 8 アカダイ RED ORG チャ BRN 6 LINE IN-C 6 チャ BRN 6 6 SHIELD G SHIELD G 05S009 * * IV-.5sq. 航法装置 / プロッタ NAVIGATOR/LOTTER HANDSET * 0 05S009 * シロ ( 太 ) クロ ( 太 ) ミドリアオアカチャキダイ SHIELD WHT[B] BLK[B] GRN BLU RED BRN YEL ORG TB リモートステーション REMOTE STATION RB-8800/880/880W * TB/TB TXD-H TXD-C RXD-H RXD-C F.GND G HANDSET * 0 遭難警報装置 DISTRESS MESSAGE CONTROLLER DMC-5 ハンドセット HANDSET * HS-8800/8800W *5 リモートステーション REMOTE STATION RB-8800/880/880W D CO-0.x: CO-SEVV-SB-C 0.x,φ0.5 CO-0.x5: CO-SEVV-SB-C 0.x5,φ.5 注記 *) 造船所手配 *) オプション *) 最大 4 台まで接続可能 *4) ケーブルクランプで接地 *5) 終端ユニットは内部のジャンパー (J,J) をONにする *6) ノーマルクローズ フローティング 最大 80mA 耐圧 50V NOTE *. SHIYARD SULY *. OTION *. MAX. 4 SETS AVAILABLE *4. GROUND THROUGH CABLE CLAM. *5. CONNECT JUMERS (J & J) ON TERMINATED REMOTE STATION. *6. NORMAL CLOSE, FLOATING, MAX80mA, WITHSTAND VOLTAGE 50V. DRAWN 6/Jan/0 CHECKED 6/Jan/0 AROVED SCALE DWG No. T.YAMASAKI T.TAKENO MASS kg C564-C04- B TITLE 名称 NAME RC-8800D/S-B (FM-8800D/S) 国際 VHF 無線電話装置 ( ラック組込 ) 相互結線図 VHF RADIOTELEHONE (RACK CONSOLE) INTERCONNECTION DIAGRAM FURUNO ELECTRIC CO., LTD.