n Compliance with IEEE 519 and other Power Quality standards n Long-term savings in system operation and maintenance cost

Transcription

1 Harmonic ilters N 3410/11 / N3412/13 Osine dvanced Passive Harmonic ilters n fficient mitigation of harmonic currents n ompliance with I 519 and other Power Quality standards n Increased equipment service life and system reliability n More efficient utilization of electric system capacity n Long-term savings in system operation and maintenance cost pprovals Technical specifications Nominal operating voltage: 3x 380 to 500V ±10% (N 3410/11) 3x 380 to 480V ±10% (N 3412/13) Operating frequency: 50Hz ±1Hz (N 3410/11) 60Hz ±1Hz (N 3412/13) Nominal motor drive input power rating: 4 to 200kW (N 3410/11) 5 to 250HP (N 3412/13) Total harmonic current distortion THID**: <5 rated power Total demand distortion TDD: ccording to I-519, table 10-3 fficiency: 98.5 to nominal line voltage and power High potential test voltage: P > 2500V (1min) Protection category: IP20 / NM1 ooling: Internal fan cooling Overload capability: 1.6x rated current for 1 minute, once per hour mbient temperature range: 25 to +50 fully operational +50 to +70 derated operation*** 25 to +85 transport and storage lammability corresponding to: UL 94V-2 or better Design corresponding to: UL 508, N , (LVD 2006/95/) 50 /460V (Mil-H-217): 200,000 hours SR****: 100k * Osine filters reduce RMS input and peak current by reducing harmonic currents and improving true power factor. ** System requirements: THVD <2%, line voltage unbalance <1% Note: performance specifications in this brochure refer to six-pulse diode rectifiers. SR rectifier front-ends will produce different results, dependent upon the firing angle of the thyristors. *** I derated = I nominal * (85 -T amb )/35 **** xternal UL-rated fuses required. Please consult the user manual. Typical electrical schematic Line L1 L2 L3 P Power capacitors Trap choke In-Out choke Power supply an ontrol error cooling power on red yellow green LD L1' Load L2' L3' NO Disconnect Monitor eatures and benefits Schaffner Osine harmonic filters represent an economical solution to the challenge of load-applied harmonics mitigation in three-phase power systems. With a plug-and-play approach and more compact dimensions than comparable products, they can be quickly installed and easily commissioned. They increase the reliability and service life of electric installations, help utilize electric sytem capacity better, and are the key to meet Power Quality standards such as I 519. Osine filters calm your harmonic waves. Schaffner Osine filters can be applied to virtually any kind of power electronics with front-end six-pulse rectifiers, where harmonic current distortion needs to be reduced to defined limits. Typical applications, where the above-mentioned non-sinusoidal consumers of power can account for a significant portion of the load, include: Typical applications n quipment with front-end six-pulse rectifier n Motor drives n actory automation equipment n Water/wastewater treatment facilities n an and pump applications n HV installations n Mission-critical processes n D fast chargers

2 > omponents > N 3410/11 / N3412/13 ilter selection table N 3410/ V/50Hz Power 400V/500V Input/Output connections apacitor disconnections Weight NM1 covers*** [kw] [kw] [W] [kg] Order code N 341x / N 341x / N 341x / N 341x / N 341x / N 341x / N 341x / N 341x / N 341x / N 341x / N 341x / N 341x / N 341x / N 341x / N 341x / N 341x / * To compile a complete part number, please replace the x with a 0 for diode or 1 for SR rectifiers. ilter to be selected by system voltage and load (motor drive) power. Note: the harmonic filter will reduce the RMS input current. xample: the rated RMS input current of an unfiltered 400V/15kW/32 drive will be reduced to approximately 23. Therefore, filter selection by current rating, as it is common for M/MI filters, is not suitable. ** alculated power loss at rated load power. *** Please contact your local Schaffner partner to order the optional NM1 covers with the order code in the table above. ilter selection table N 3412/13 460V/60Hz Power 460V Input/Output connections apacitor disconnections Weight NM1 covers*** [HP] [W] [kg] Order code N 341x N 341x N 341x N 341x N 341x N 341x N 341x N 341x N 341x N 341x N 341x N 341x N 341x N 341x N 341x N 341x * To compile a complete part number, please replace the x with a 2 for diode or 3 for SR rectifiers. ilter to be selected by system voltage and load (motor drive) power. Note: the harmonic filter will reduce the RMS input current. xample: the rated RMS input current of an unfiltered 460V/20HP/28 drive will be reduced to approximately 20. Therefore, filter selection by current rating, as it is common for M/MI filters, is not suitable. ** alculated power loss at rated load power. *** Please contact your local Schaffner partner to order the optional NM1 covers with the order code in the table above. Osine Mains N (110kW/400V) Non-linear load 1: 30kW/400V Non-linear load 2: 75kW/400V

3 > omponents > N 3410/11 / N3412/13 Mechanical data N 3410/ N to -110 N 3410/ N to -210 N 3412/ N to -130 N 3412/ N and -190 N 3410/ N and -320 Installation. ll filters from N 341x-8 to -130 are wall N 3412/ N and -310 mountable and have to be operated vertically. The filters N 341x-150 and higher are designed for floor mounting. In order to allow for sufficient air flow all filters must be clear on top and bottom min. 150mm. Optional NM1 cover. ll filters can be optionally fitted with a NM1 cover. Please find order codes on previous pages. W Z V X Y

4 > omponents > N 3410/11 / N3412/13 Dimensions N 3410/ N N 3412/ N x30 14x30 14x30 14x30 14x30 M6 M6 M6 M6 M8 M8 M8 M8 M8 M10 M10 M10 M10 M10 M10 M10 M10 V W 6 6 X Y Z ll dimensions in mm; 1 inch = 25.4mm Tolerances according: ISO 2768-m / N m ilter connector cross sections Solid wire 16mm 2 35mm 2 50mm 2 95mm 2 10mm 2 lex wire 10mm 2 25mm 2 50mm 2 95mm 2 6mm 2 W type wire W 6 W 2 W 1/0 W 4/0 W 8 Recommended torque Nm Nm 7 8Nm 17 20Nm Nm Please visit to find more details on filter connectors. Your local partner: To find your local partner within Schaffner s global network, please go to May 2011

5 Headquarters and global innovation and development center Schaffner roup Nordstrasse Luterbach Switzerland T info@schaffner.ch Sales and application centers hina Schaffner M Ltd. Shanghai uilding 11, Lane 1365 ast Kangqiao Road Shanghai T cschina@schaffner.com ermany Schaffner Deutschland mbh Schoemperlenstrasse Karlsruhe T germanysales@schaffner.com inland Schaffner Oy Tynninkuja Lohja T finlandsales@schaffner.com rance Schaffner M S..S. 112, Quai de ezons rgenteuil T francesales@schaffner.com Italy Schaffner M S.r.l. Via alileo alilei, inisello alsamo (MI) T / italysales@schaffner.com apan Schaffner M K.K. Mitsui-Seimei Sangenjaya ldg , Kamiuma, Setagaya-ku Tokyo T japansales@schaffner.com Sweden Schaffner M Turebergstorg 1, Sollentuna T / swedensales@schaffner.com Switzerland Schaffner MV Nordstrasse Luterbach T sales@schaffner.ch Singapore Schaffner M Pte Ltd. lk 3015 Ubi Road Kampong Ubi Industrial state T singaporesales@schaffner.com Spain Schaffner M spaña alle aléndula 93, Miniparc III, dificio l Soto de la Moraleja, lcobendas Madrid T spainsales@schaffner.com Taiwan Schaffner MV Ltd. 6th loor, No 413 Rui uang Road Neihu District Taipei ity 114 T taiwansales@schaffner.com Thailand Schaffner M o. Ltd. Northern Region Industrial state 67 Moo 4 Tambon an Klang mphur Muang P.O. ox 14 Lamphun T thailandsales@schaffner.com UK Schaffner Ltd. 5 shville Way Molly Millars Lane Wokingham erkshire R41 2PL T uksales@schaffner.com US Schaffner M Inc. 52 Mayfield venue dison, New ersey T usasales@schaffner.com /us To find your local partner within Schaffner s global network, please go to May Schaffner M. Specifications subject to change without notice. ll trademarks recognized. Schaffner is an ISO-registered company. Its products are designed and manufactured under the strict quality and environmental requirements of the ISO 9001 and ISO standards. This document has been carefully checked. However, Schaffner does not assume any liability for errors or inaccuracies.