PhotoSweep V. Set-up Guide. by Spacesaver
|
|
- Charla Carter
- 5 years ago
- Views:
Transcription
1 PhotoSweep V by Spacesaver Set-up Guide ssc@spacesaver.com Internet: CAUTION Spacesaver Recommends: 1. That Safety Glasses be worn during any cutting and drilling operations and grinding. 2. That safety gear such as Hard Hats, Safety Shoes, etc. be worn when required. Spacesaver OP-1117
2 CONTENTS PAGE # SECTION 3 SECTION I - GENERAL INFORMATION 4-6 SECTION II - COMPONENT IDENTIFICATION 7 SECTION III - SETTING INTENSITY GAIN 8 SECTION IV - OUTPUT LED INDICATOR 8 SECTION V - FINAL SAFETY TEST Spacesaver OP Page 2
3 SECTION I - GENERAL INFORMATION After installation or service of any Powered Spacesaver Mobile System, you must test the function of the PhotoSweeps. 1. Place an object at least 1 in height at mid aisle. - If you have nested or waist high sweeps, you will need to test with a similar device to block the sweep beam. 2. Move carriage toward the object. 3. Assure each carriage stops just prior to touching the object. 4. If carriage fails to stop before touching the object, adjust gain and repeat test. 1. Each aisle must be protected by a minimum of one floor level sweep. 2. Any system that has an auto-move function must be protected by two safety devices per aisle, except the outside aisles which must have at least one floor level sweep. 3. Some auto moves require ZFS as the second safety devices. 4. Typically PhotoSweeps are planned to Transmit right to left when facing the component pair. This may be altered in rare circumstances to prevent errant locked aisles. Watch your planning paperwork for more details. 5. The Gain adjustment pods (potentiometer) is very fragile. Use a small jewelers screwdriver for all adjustments. 6. Gain is adjusted from the 11:00 O clock position (least gain) to 7:00 O clock (highest gain). 7. We recommend pre-setting the gain prior to attaching the components to the Spacesaver system. 8. Final adjustment and testing must be done after power is applied to the system. 9. Do not pinch any wires when mounting Photosweep housings. Pinched wires may result in equipment damage. Spacesaver OP Page 3
4 SECTION II - COMPONENT IDENTIFICATION TRANSMITTER RECEIVER TRANSMITTER ASSEMBLY - SPACESAVER COMMERCIAL RECEIVER ASSEMBLY - SPACESAVER COMMERCIAL Spacesaver OP Page 4
5 C16SPSTX TRANSMITTER ASSEMBLY - SPACESAVER ACTIVRAC16 C16SPRX RECEIVER ASSEMBLY - SPACESAVER ACTIVRAC 16 Spacesaver OP Page 5
6 TRANSMITTER ASSEMBLY - SPACESAVER ACTIVRAC RECEIVER ASSEMBLY - SPACESAVER ACTIVRAC 7 Spacesaver OP Page 6
7 SECTION III - SETTING INTENSITY GAIN 1. Adjust the potentiometer on the Transmitter and Receiver to the correct gain listed in the chart below. 2. Mount the components as instructed in the wiring installation manual for the product you are installing. Use caution to not pinch the wire (s) as this could cause logic board damage. 3. After powering the Spacesaver system, verify the Transmitter is emitting a red pulsing light. If the LED is not pulsing, increase the gain at the potentiometer. 4. Increase the gain on the Receiver until the LED on the face of the component starts to blink red. 5. Decrease the gain until the LED just begins to blink green. Initial gain adjustment Carriage length in feet Spacesaver OP Page 7
8 SECTION IV - RECEIVER OUTPUT INDICATOR LED OFF - There is no light being received from the Transmitter Yellow - There is a weak light signal being received. Green - The proper amount of light is being received. Red - Too much light is being received. SECTION V - FINAL SAFETY TEST After installation or service of any Powered Spacesaver Mobile System, you must test the function of the PhotoSweeps. 1. Place an object at least 1 in height at mid aisle. - If you have nested or waist high sweeps, you will need to test with a similar device to block the sweep beam. 2. Move carriage toward the object. 3. Assure each carriage stops just prior to touching the object. 4. If carriage fails to stop before touching the object, adjust gain and repeat test. Spacesaver OP Page 8
9 Spacesaver Corporation 1450 Janesville Avenue Fort Atkinson, WI KI 1330 Bellevue Street P.O. Box 8100 Green Bay, WI Spacesaver Corporation is a division of KI. KI is a registered trademark of Krueger International, Inc. Spacesaver is a registered trademark of Spacesaver Corporation KI and Spacesaver Corporation. All Rights Reserved. Litho in USA. OP-1117 SSC/SSC Spacesaver OP-1117
FACE PANELS & INSTALLATION INSTRUCTIONS MANUAL, MECHANICAL ASSIST & ECLIPSE POWERED SYSTEMS TM SECTION I SECTION II SECTION III SECTION IV SECTION V
FACE PANELS & BACK PANELS by Spacesaver INSTALLATION INSTRUCTIONS MANUAL, MECHANICAL ASSIST & ECLIPSE POWERED SYSTEMS TM SECTION I INTRODUCTION SECTION II LIBRARY SHELVING PANELS SECTION III 4-POST SHELVING
More informationShelving 4-POST & CASE-TYPE
Shelving 4-POST & CASE-TYPE S H E L V I N G S Y S T E M S S t o r a g e S o l v e d MAXIMUM FLEXIBILITY Attractive, versatile and easy to access, Spacesaver 4-Post and Case-Type Shelving are highly adaptable,
More information4-POST & CASE-TYPE SHELVING SYSTEMS
F i l e & S t o r a g e S h e l v i n g 4-POST & CASE-TYPE SHELVING SYSTEMS S t o r a g e S o l v e d 4-POST SHELVING SYSTEMS D e s i g n F e a t u r e s Shelves Standard 22-gauge (.75 mm) or heavy-duty
More informationModular Bi-File Lateral
Modular Bi-File Lateral Installation Instructions 920-563-6362 E-mail: ssc@spacesaver.com Internet: www.spacesaver.com Contents Hardware Identification..................................3 Pre-Installation........................................6
More informationUniframe Tables and Convertible Bench
Uniframe Tables and Convertible Bench The easy transformation. Easy to operate. Easy to move. Easy to store. 2 Uniframe Tables and Convertible Bench: Transforming multi-use spaces. Cafeteria. Study Hall.
More informationOPTIONAL RF CONTROL SECTION III SECTION IV STATIC CAUTIONS INSTALLATION INSTRUCTIONS RETRO FIT INSTALLATION INSTRUCTIONS SETTING ZONE CONFIGURATIONS
OPTIONAL RF CONTROL SECTION I STATIC CAUTIONS SECTION II INSTALLATION INSTRUCTIONS SECTION III RETRO FIT INSTALLATION INSTRUCTIONS SECTION IV SETTING ZONE CONFIGURATIONS INSTALLATION INSTRUCTIONS O P T
More informationUniframe. Tables and Convertible Bench easy to operate easy to move easy to store
Uniframe Tables and Convertible Bench easy to operate easy to move easy to store 2 Sit on it. Sit at it. Nest it. Roll it away. UNIFRAME Convert a room to anything you want it to be... cafeteria, study
More informationVersa Chairs. A large family with a common theme - comfort. Modest price Clean design
Versa Chairs A large family with a common theme - comfort. Durable construction Modest price Clean design What makes Versa one of KI s most popular chairs? Versa offers big comfort in a small-scale chair.
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationAssembly Instructions
Jury Base Seating January 2014 - Floor Anchor Specifications / 4 5 / 16 (4)½ diameter holes 1/ 4 2 4 8 #12.750.KIT4 1 5 / Hilti 4 KH-EZx2/ 8 Max. Torque: 18 ft/lbs punch clearance hole in carpet before
More informationCrossRoads Library Furniture
CrossRoads Library Furniture CrossRoads Furniture. Where people and knowledge meet! Inviting transitional design. Old-world craftsmanship. Cutting-edge power/data. CrossRoads Library Furniture There's
More informationAssembly Instructions
RoomScape Furniture System March 2013 - Bed Styles bed deck board bed deck board top cap top cap base glide middle side rail frame frame stacking device frame middle lower reinforcement side rail Single
More informationWood Casegoods. Da Vinci. Delsanti. Darwin. Three collections High-quality craftsmanship Environmentally friendly
Wood Casegoods Da Vinci. Delsanti. Darwin. Three collections High-quality craftsmanship Environmentally friendly Delsanti Darwin Da Vinci 2 Da Vinci, Delsanti, Darwin : a natural selection. KI s wood casegoods
More informationBulk Storage Rack Assembly Instructions
Bulk Storage Rack Assembly Instructions Upright Frame Assembly Determine which end of the post goes up. The keystone slots on the front face of the post are wider at the top than at the bottom (see diagram
More informationPet Door Panel Installation Manual
Pet Door Panel Installation Manual 400-558-1 1 4/3/03, 3:26 PM Components: Pet Door Panel Panel Latch Assembly Foam Weather-stripping Glass Sweep (4) Binding Posts (6) #6 x 1/2 Sheet Metal Screws (4) 8-32
More informationIntroduction...1 Overview...2. Beacon Transmitter...7. Beacon Receiver Trouble Shooting...15
MoTeC Lap Beacon Manual Contents Introduction...1 Overview...2 Operation...2 ID Number...3 Lap Beacon Use...4 Split Beacon Use...4 Verifying Operation...5 Beacon Transmitter...7 Position...7 Spacing between
More informationINSTALLATION GUIDE. Version 2.0
INSTALLATION GUIDE Version 2.0 INTRODUCTION Carefully read these instructions to assure proper installation and performance of the GatorDeck TM. TOOLS NEEDED 1. Calibrated test weights 2. Phillips screwdriver
More informationASSEMBLY INSTRUCTIONS FOR SL500A AND SL500AL
ASSEMBLY INSTRUCTIONS FOR SL500A AND SL500AL January 2013 The SL500A is a square upright glass cabinet with a single hinged lockable door. It has five adjustable shelves plus the base. It also has an optional
More informationApexDesk Assembly Guide
ELECTRIC HEIGHT-ADJUSTED SIT TO STAND DESK ApexDesk Assembly Guide REV-1507C Table of Contents CAUTION, USE & LIABILITY... 3 PARTS & HARDWARE LIST... 4 PARTS / COMPONENT DIAGRAMS... 5 ASSEMBLY INSTRUCTIONS...
More informationTechnical Guide for Radio-Controlled Advanced Wireless Lighting
Technical Guide for Radio-Controlled Advanced Wireless Lighting En Table of Contents An Introduction to Radio AWL 1 When to Use Radio AWL... 2 Benefits of Radio AWL 5 Compact Equipment... 5 Flexible Lighting...
More informationInstallation Manual MODEL E-42
Installation Manual MODEL E-42 GET TO KNOW YOUR UNIT 2 (BOTTOM OF RACEWAY) 1 3 1. CROSS BRACES 2. ELECTRICAL RACEWAY 3. ELECTRICAL OUTLET - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver
More informationHigh Bay Occupancy Sensor for Use with Electronic Ballast HID Luminaires
Instruction Bulletin 63249-500-08A6 05/2011 High Bay Occupancy Sensor for Use with Electronic Ballast HID Luminaires SLSPIP210EB and SLSPIP210EBCT INTRODUCTION Figure 1: High Bay Occupancy Sensor for Use
More informationTABLE OF CONTENTS INTRODUCTION...04 PART I - HEALTH LEARNING...08 PART II - DEVICE LEARNING...12 PART III - BUILD...16 PART IV - DATA COLLECTION...
YOUTH GUIDE ENGINEER NOTES TABLE OF CONTENTS INTRODUCTION...04 PART I - HEALTH LEARNING...08 PART II - DEVICE LEARNING...12 PART III - BUILD...16 PART IV - DATA COLLECTION...18 PART V - COOL DOWN...22
More informationPro-Weigh 84/SS/FLP Lo Pro 90 / SS Installation Guide. Version 1.0
Pro-Weigh 84/SS/FLP Lo Pro 90 / SS Installation Guide Version 1.0 INTRODUCTION The scale must not be loaded beyond its capacity. Do not select a site where overweight load would have to maneuver to avoid
More informationINSTRUCTION MANUAL DWX723-XE HEAVY-DUTY MITER SAW STAND FINAL PAGE SIZE : 8.5IN X 5.5IN
INSTRUCTION MANUAL DWX723-XE HEAVY-DUTY MITER SAW STAND FINAL PAGE SIZE : 8.5IN X 5.5IN DWX723-XE MITER SAW STANDS Components List A. Beam B. DW7231 Miter saw mounting brackets C. Extension arm D. DW7232
More informationWestern Products, PO Box , Milwaukee, WI MOUNT KIT. Model No Ford F-150 4X
Western Products, PO Box 245038, Milwaukee, WI 53224-9538 www.westernplows.com November 1, 2009 Lit. No. 64461, Rev. 05 64500 MOUNT KIT Model No. 3239 Ford F-150 4X4 2004-08 Installation Instructions Read
More informationWireless Occupancy Sensor User Guide
Wireless Occupancy Sensor Wireless Occupancy Sensor User Guide This Manual covers both the Wide angle and the Narrow long range occupancy sensor. Dialight Part Numbers described here-in are: WOSU22BG2
More informationPage 1 of 18. SunRail System Installation Instructions
Page 1 of 18 SunRail System Installation Instructions Page 2 of 18 SunRail Stainless Steel Railing Installation Guide Table of Contents Before You Begin 3 Installing Surface Mount Bases for a Two Rail
More informationSQM5 Reversing Actuators, with Multiple Analog Control Input Signals
Document No. 9-4 June, 5 SQ5 Reversing Actuators, with ultiple Analog Control Input Signals Product Description Reversing actuator used to position flow control valves, butterfly valves, dampers, or any
More information6 Foot/ 1800mm Aisle Width Net-Contain Aisle Containment for N-Type and S-Type Cabinets
6 Foot/ 1800mm Aisle Width Net-Contain Aisle Containment for N-Type and S-Type Cabinets Panduit Corp. 2016 INSTALLATION INSTRUCTIONS Page 1 of 36 Component Guide for Doors Dual Sliding Containment Door
More informationPrice list Portavant 80 automatic. Glass fittings with logic. New! Automatically convincing! SAFETY FIRST
Glass fittings with logic Price list Portavant 80 automatic New! Automatically convincing! SAFETY FIRST Select the solution to meet your needs in only three steps, using our complete sets. Select installation
More informationFORD F450 & F PLOW UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA07661B)
BOSS PRODUCTS A Division of Northern Star Industries, Inc. P.O. Box 787 Iron Mountain MI 49801-0787 www.bossplow.com 1999-2007 FORD F450 & F550 10 PLOW UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA07661B)
More informationDR-TRC105-EV Evaluation Kit. User s Guide
DR-TRC105-EV Evaluation Kit User s Guide DR-TRC105-304-EV DR-TRC105-315-EV DR-TRC105-345-EV DR-TRC105-372-EV DR-TRC105-390-EV DR-TRC105-403-EV DR-TRC105-434-EV DR-TRC105-450-EV 2010-2015 by Murata Electronics
More informationCHEVROLET 3/4 TON RT3 UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA03699)
BOSS PRODUCTS A Division of Northern Star Industries, Inc. P.O. Box 787 Iron Mountain MI 49801-0787 www.bossplow.com 1999 2002 CHEVROLET 3/4 TON MOUNTING INSTRUCTIONS (PART NO. LTA03699) PUSHING THE EDGE
More information1/4in. SHEET PALM SANDER
1/4in. SHEET PALM SANDER OPERATING INSTRUCTIONS SPECIFICATIONS ITEM# 151608 Voltage: Max. output: No load speed: Cord: 120V ~ 60Hz 180W 14000 RPM 6 feet (2m) Dust-Sealed On/off Switch Dust Extraction Adaptor
More informationREC Series Rack Installation Guide
REC Series Rack Installation Guide 1 REC Series Rack Installation Guide TABLE OF CONTENTS SECTION SAFETY WARNINGS 1 600 WIDE EXPLODED VIEW 2 800 WIDE EXPLODED VIEW 3 SWITCHING DOOR HANDING 4 STABILIZING
More informationInstallation Manual MODEL AE-46
Installation Manual MODEL AE-46 GET TO KNOW YOUR UNIT (BOTTOM OF RACEWAY) 2 5 1 4 6 3 1. CROSS BRACES 2. ELECTRICAL RACEWAY 3. SIDE BRACKETS 4. ELECTRICAL CORD COVER 5. ELECTRICAL OUTLET 6. HOT IRON REST
More informationSash and/or Hinge Replacement Guide for Andersen 200 Series Basement/Utility Windows
and/or Hinge Replacement Guide for Andersen 200 Series Basement/Utility Windows Please read this guide completely before starting. For questions about this and other Andersen products, call 1-888-888-7020.
More informationRolling Curtain door Manual
Rolling Curtain door Manual Installation Maintenance parts Model 944 PHONE 800 448 8979 FAX 800 236 8722 website www.tracrite.com EMAIL tr@tracrite.com ADDRESS 216 Wilburn Road Sun Prairie, WI 53590 This
More informationINSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT
INSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT BACKGROUND Proper alignment of the transmission input shaft to the crankshaft centerline is required in order to achieve the best results
More informationACTIVITY 1. Exploring LEDs and Lamps
Name: Class: SOLIDS & Visual Quantum Mechanics LIGHT ACTIVITY 1 Exploring LEDs and Lamps Goal In this activity, you will explore the effect of changing the energy supplied to incandescent lamps and light
More informationFORD F150, F250, & F350 RT3 UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA03674)
BOSS PRODUCTS A Division of Northern Star Industries, Inc. P.O. Box 787 Iron Mountain MI 49801-0787 www.bossplow.com 1981 1991 FORD F150, F250, & F350 MOUNTING INSTRUCTIONS (PART NO. LTA03674) PUSHING
More informationAssembly instructions for the swivel castor kit
Assembly instructions for the swivel castor kit Thank you very much for choosing a Sport-Thieme product. Please read the instructions fully before you assemble the equipment so you can enjoy the product
More informationULT R A S PACE SAV E R SQ UA R E D
ULT R A S PACE SAV E R SQ UA R E D Hip to be Square Dero s Ultra Space Saver Squared offers high-security, vertical bike parking. Adjustable sliding arms make it easy for customers to best utilize their
More information1. Diffuse sensor, intensity difference 2. Diffuse sensor with background suppression 3. Retro-reflective sensor with polarization filter 4.
Table of contents 1. Diffuse sensor, intensity difference 2. Diffuse sensor with background suppression 3. Retro-reflective sensor with polarization filter 4. Through beam sensor 5. Fiber Optic Sensor
More informationTRC EV DR TRC EV DR TRC EV
DR-TRC103-EV Evaluation Kit User s Guide DR TRC103 868 EV DR TRC103 915 EV DR TRC103 950 EV DR-TRC103-EV User s Guide (2015/04/17) Page 1 of 11 www.murata.com Introduction The DR TRC103 series evaluation
More informationFlat Panel Tilt Wall Mount (GPM-111)
INSTALLATION INSTRUCTIONS Flat Panel Tilt Wall Mount () The tilt wall mount fits most 23 to 30 displays. The is designed to adapt to VESA 200mm/100mm compliant displays. This mount will also adapt to standard
More informationContents Introduction...2 Revision Information...3 Terms and definitions...4 Overview...5 Part A. Layout and Topology of Wireless Devices...
Technical Information TI 01W01A51-12EN Guidelines for Layout and Installation of Field Wireless Devices Contents Introduction...2 Revision Information...3 Terms and definitions...4 Overview...5 Part A.
More informationFORD F150, F250 (UNDER 8500 GVWR) SPORT DUTY UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA05440)
BOSS PRODUCTS A Division of Northern Star Industries, Inc. P.O. Box 787 Iron Mountain MI 49801-0787 www.bossplow.com 1997-2003 FORD MOUNTING INSTRUCTIONS (PART NO. LTA05440) PUSHING THE EDGE MSC05449-2
More informationMedia Low Sensor Maintenance Kit
Media Low Sensor Maintenance Kit Installation Instructions This kit includes the parts and documentation necessary to install the Media Low Sensor maintenance kit in the Xi4 printers. Read these instructions
More informationUNIVERSAL UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA07667B)
BOSS PRODUCTS A Division of Northern Star Industries, Inc. P.O. Box 787 Iron Mountain MI 49801-0787 www.bossplow.com UNIVERSAL UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA07667B) DRIVEN TO BE THE
More informationBarn Door & Hardware Installation Guide
Barn Door & Hardware Guide INTRODUCTION Thank you for purchasing our hardware. Our barn door and hardware will add a stunning accent to your living environment and maximize its space. This manual covers
More informationIt s all about communication.
It s all about communication. A VISUAL GUIDE As a manual photographer hoping to create amazing images totally in-camera, it's vital to be able to use a flash off-camera confidently. This means not only
More informationMachining Laboratory Regulations and Safety
Machining Laboratory Regulations and Safety General Laboratory Regulations Each person using the manufacturing laboratory is expected to comply with the following rules and regulations failure to do so
More informationThe Machining Lab. The grading for this portion of the class will be as follows:
The Machining Lab 1.0 Expected Learning Outcomes Understand how to operate common machine shop equipment safely. Demonstrate capability to use machine shop equipment to fabricate simple experimental apparatus.
More informationInstruction Manual ABM HART Gateway Software. Instruction Manual Revision A.1
Instruction Manual ABM HART Gateway Software Instruction Manual Revision A.1 Table of Contents Section 1: Getting Started... 3 1.1 Setup Procedure... 3 1.2 Quick Setup Guide for Ultrasonic Sensors... 11
More informationChicken Coop OWNER S MANUAL
Chicken Coop OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result
More informationBFS / BFSM SERIES Installation & Maintenance Manual
Introduction: The BFS / BFSM series electric actuators have battery backup modules for fail safe operation. The BFS series is for two position control and the BFSM series is for proportional control, both
More informationFinal Mini Project Report
Integrated System Analysis Team 1 Savath Lieng: Leader Jose Diaz: Certifier Shabuktagin Photon Khan: Rapporteur Abstract This mini project III shows an integrated system analysis. In this project, we built
More informationRED TACTON.
RED TACTON www.technicalpapers.co.nr 1 ABSTRACT:- Technology is making many things easier; I can say that our concept is standing example for that. So far we have seen LAN, MAN, WAN, INTERNET & many more
More informationTS-20KD-1010 LOW PROFILE CARGO SCALE INSTALLATION GUIDE
TS-20KD-1010 LOW PROFILE CARGO SCALE INSTALLATION GUIDE Triner Scale & Mfg. Co., Inc. 8411 Hacks Cross Rd. Olive Branch, MS 38654 Phone: 800-238-0152 Fax: 662-809-2386 Description The Triner Scale Model
More informationGPS Wireless Clock System User Manual. Synchronized Solutions for every type of facility SCHOOLS HEALTHCARE GOVERNMENT INDUSTRIAL CORPORATE
GPS Wireless Clock System User Manual Synchronized Solutions for every type of facility SCHOOLS HEALTHCARE GOVERNMENT INDUSTRIAL CORPORATE CONTENTS Product Description...........................................................................
More informationPrim-Jack. Floor Tightening Jack for Tongue & Groove Flooring
Prim-Jack Floor Tightening Jack for Tongue & Groove Flooring CAUTION - READ IMPORTANT SAFETY AND OPERATION INSTRUCTIONS BEFORE OPERATING YOUR PRIM-JACK. Your new Prim-Jack is capable of dependable performance
More informationDiscussion on Red Tacton - Technology for communication through Human body
Discussion on Red Tacton - Technology for communication through Human body 1 2 K. Gandhimathi, AP/CSE, A.Praveena, AP/Chemistry 1,2 Idhaya Engineering College for women, Chinnasalem E- mail: 1 pk.gmathi@gmail.com,
More informationINSTALLATION INSTRUCTIONS John Deere 600C Corn Head Auger Trough Liner
www.polyskid.com P.O. Drawer 349, Monticello, GA 31064 Phone: 800.542.7659 Fax: 706.468.2881 e-mail: polytech@polyskid.com INSTALLATION INSTRUCTIONS John Deere 600C Corn Head Auger Trough Liner IT IS VERY
More informationWindload Post 9100/9600/9900 Installation Instructions
Windload Post 9100/9600/9900 Installation Instructions Wayne Dalton, a division of Overhead Door Corporation P.O. Box 67, Mt. Hope, OH 44660 www.wayne-dalton.com Wayne-Dalton Corp. P.O. Box 67 Mt. Hope,
More informationASSEMBLY AND INSTALLATION INSTRUCTIONS
ASSEMBLY AND INSTALLATION INSTRUCTIONS Model 1425 Aluminum Swivel Rack IMPORTANT BEFORE YOU BEGIN Read these instructions and warnings completely before installation. CAPACITY 200 lbs. MAXIMUM NOTE: This
More informationOperating Manual 6 Industrial Bench Grinder ATBG280/
Operating Manual 6 Industrial Bench Grinder ATBG280/6 804531 40 Year Australian Heritage The reputable name in bench grinders for 40 years Protect yourself and others by observing all safety information,
More informationAddendum to HQ 24 Fusion User Manual
Addendum to HQ 24 Fusion User Manual The touch screen display photographed in the manual may be different from the one you received with your HQ 24 Fusion. These pages replace portions of the printed HQ
More informationEZ-MATRIX I N S TA L L AT I O N I N S T R U C T I O N S EZ-MATRIX
TM I N S TA L L AT I O N I N S T R U C T I O N S READ THESE INSTRUCTIONS page 2 Installer Tips: Installation is best completed with the help of one or two people. Prior to beginning, please read through
More informationULT R A SPAC E SAV E R
ULT R A SPAC E SAV E R Double Capacity, Modular Construction The Ultra Space Saver provides easy and ample space for u-lock security on nearly any bike, including bikes with fenders. Thanks to design enhancements,
More informationS-COR. FIGURE 1 Wiring Diagram NOTE: To reset S-COR to factory settings, press and! hold < and > buttons upon power up. INSTALLATION INSTRUCTIONS
Section 1 General Description The ClearPath Spectrum Wireless System is comprised of two devices; a Coordinator () that functions in a similar role as traditional wireless system receivers, and a Transceiver
More informationAssembly Instructions. Important!
Play Action Spiral Tube Slide Assembly Instructions Important! Intended for residential use by children ages 2 to 10, only on properly installed PlayStar playsets. Before use refer to complete safety guidelines
More informationTable of Contents Heavy Duty Extra Long Poly Blade
Table of Contents Heavy Duty Extra Long Poly Blade Arctic Heavy Duty Poly Blade 90" & 96" (Blade, Quadrant & A-frame)... 2 Power angling installation.....7 Shock absorber installation....12 Pro-Wings installation..
More informationB32157 UNDERCARRIAGE KIT. Jeep Cherokee Jeep Wagoneer Jeep Comanche Parts List and Installation Instructions CAUTION
October 15, 2007 Lit. No. B64110, Rev. 01 B32157 UNDERCARRIAGE KIT Jeep Cherokee 1984-01 Jeep Wagoneer 1984-93 Jeep Comanche 1986-92 Parts List and Installation Instructions Read this document before installing
More informationPOWERLINE HEAVY DUTY ISOLATORS
POWERLINE HEAVY DUTY ISOLATORS MODELS: 22-15, 22-18, 22-21, 22-63, 33-94, 33-115 CONGRATULATIONS! for choosing this high quality POWERLINE PRODUCT. The latest state of the art engineering plus years of
More informationShelf Converter Drawer System
Shelf Converter Drawer System Installation and Use Instructions IF THIS PRODUCT IS INSTALLED IN A UNIT THAT DOES NOT MEET THE MINIMUM SYSTEM REQUIREMENTS, INJURY COULD RESULT. (SEE PAGE 2) Shelf Converter
More informationChicken Coop OWNER S MANUAL
Chicken Coop OWNER S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result
More informationJob Sheet 2 Servo Control
Job Sheet 2 Servo Control Electrical actuators are replacing hydraulic actuators in many industrial applications. Electric servomotors and linear actuators can perform many of the same physical displacement
More informationCHEV / GMC 3500 HD RT II TM UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA03598)
BOSS PRODUCTS A Division of Northern Star Industries, Inc. P.O. Box 787 Iron Mountain MI 49801-0787 www.bossplow.com 1991-2002 CHEV / GMC 3500 HD RT II TM UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO.
More informationFORD MOUNT INSTALLATION INSTRUCTIONS
WESTERN PRODUCTS, P.O. BOX 245038, MILWAUKEE, WI 53224-9538 Lit. No. 64289 June 1, 2003 FORD MOUNT INSTALLATION INSTRUCTIONS Bronco (4X4 only) F-150 (4X4 only), F-250/350 Super Duty 1980 1991 Model No.
More informationGE Lighting. Albeo LED Luminaire. High Bay Lighting. (ABV-Series) imagination at work
GE Lighting Albeo LED Luminaire High Bay Lighting (ABV-Series) imagination at work Product Features Albeo continues to build on the groundbreaking ABH-Series high bay LED luminaire with its latest high
More informationCornerstone Electronics Technology and Robotics Week 21 Electricity & Electronics Section 10.5, Oscilloscope
Cornerstone Electronics Technology and Robotics Week 21 Electricity & Electronics Section 10.5, Oscilloscope Field trip to Deerhaven Generation Plant: Administration: o Prayer o Turn in quiz Electricity
More informationOXYGEN INSTALLATION. Revision date
12345 1 Hardware List 12345 Flat head wood screw #9 x 7/8 long with #2 Phillips drive, silver Used to attach surfaces and end panels Hex set screw ½-13 x 2 long with 1/4 hex drive, black Used on Legs Hex
More informationTRILENNIUM FULL SCOPE (FS) TEMPLATE INSTRUCTIONS
Overview Parts Included in Template System: Full Scope (FS) Template Rails, with ø 2-1/8 Crossbore Guides. FS Router Carrier (for 1-3/4, 2 & 2-1/4 Doors) FS Bridges, Stops and Twist Bolts 13/16 x 5 Router
More informationInstallation Instructions
Installation Instructions Curved Glass Screen Installation Instructions Important Information Please read these instructions carefully before starting installation and keep for future reference. Remove
More informationIntroduction. Theory of Operation
Mohan Rokkam Page 1 12/15/2004 Introduction The goal of our project is to design and build an automated shopping cart that follows a shopper around. Ultrasonic waves are used due to the slower speed of
More informationWINDLOAD POST WayneMark 8000, 8100 INSTALLATION INSTRUCTIONS
WINDLOAD POST WayneMark 8000, 8100 INSTALLATION INSTRUCTIONS Wayne Dalton, a division of Overhead Door Corporation P.O. Box 67, Mt. Hope, OH 44660 www.wayne-dalton.com See garage door owner s manual for
More informationInstallation Instructions
Contents Page General Information and Installer Tips.......... 2 Panels & Posts............................. 3 Enclosure Description..................... 4 Hinge Door Hardware................... 4-5 Step-by-Step
More informationInstructions for programming and use Starline Roldeck - floorpanel control RD-2001
Instructions for programming and use Starline Roldeck - floorpanel control RD-2001 Microprocessor-based Roldeck control Copyright Starline Technical Support BV. The Netherlands. Alle rechten voorbehouden.
More informationLap Triggers. Application Note. McLaren Electronic Systems McLaren Technology Centre Chertsey Road Woking Surrey GU21 4YH UK
McLaren Technology Centre Chertsey Road Woking Surrey GU1 YH UK McLaren Electronics Inc. Suite 11 Bostick Building 9801 West Kincey Avenue Huntersville NC 8078 USA Copyright McLaren Electronics 01 Revision
More informationTM POWER AMPLIFIER AM-6545A/GRC-193A (NSN )
TECHNICAL MANUAL GENERAL SUPPORT MAINTENANCE MANUAL POWER AMPLIFIER AM-6545A/GRC-193A (NSN 5820-01-186-3699) HEADQUARTERS, DEPARTMENT OF THE ARMY 15 JANUARY 1986 \ Technical Manual No. 11-5820-921-40-2
More informationTLKR T60 OWNER'S MANUAL EN DE FR IT ES PR NL DA NO TU PL SV RU
TLKR T60 OWNER'S MANUAL EN DE FR IT ES PR NL DA NO TU PL SV RU SF 1 PRODUCT SAFETY AND RF EXPOSURE FOR PORTABLE TWO-WAY RADIOS! Caution ATTENTION! Before using this product, read the RF energy awareness
More informationMicromachining of Glass by Laser Induced Deep Etching (LIDE) LPKF Vitrion 5000
Micromachining of Glass by Laser Induced Deep Etching (LIDE) LPKF Vitrion 5000 In microsystems technology, glass is very suitable as a substrate material for a variety of applications. The basis for the
More informationINSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111
INSTALLATION INSTRUCTIONS Flat Panel Static Wall Mount Model: GSM-111 The GSM-111 static wall mount fits most 23" to 30" displays. The GSM-111 is designed to adapt to VESA 200mm/ 100mm compliant displays.
More informationTilting Wall Mount Fits 37" to 70" Flat Panel TVs Model No: DCD13020
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE. Lot Number: Date: Tilting Wall Mount Fits 37" to 70" Flat Panel TVs Model No: DCD1300 MIN:7.87
More informationNESS L300 System Components
NESS L300 System Components 5 Functional Stimulation (FS) Cuff Your L300 FS Cuff (see figure 5-1) is lightweight and easily fits under most clothing. It features a cradle for the RF Stim Unit and an anatomically
More informationInstallation Manual MODEL NE-42
Installation Manual MODEL NE-42 GET TO KNOW YOUR UNIT 1 1. CROSS BRACES - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with 1/4 & 1/8 drill bit)
More informationMATRIX GUARD. I nstallation I nstructions TERMS AND CONDITIONS. Call or visit
TERMS AND CONDITIONS It is the intent of Wireway Husky Corp. that any product received by our Customers fully meets their expectations. MATRIX GUARD Wireway Husky product is Marketed and Distributed by
More informationEssentia Electromagnetic Monitor Model: EM2
Essentia Electromagnetic Monitor Model: EM2 The Essentia EM2 was designed to bridge the gap between inexpensive monitors with limited response and expensive full spectrum units. It has a small, sensitive
More information