Sash and/or Hinge Replacement Guide for Andersen 200 Series Basement/Utility Windows

Size: px

Start display at page:

Download "Sash and/or Hinge Replacement Guide for Andersen 200 Series Basement/Utility Windows"

Mavis Ball
6 years ago
Views:

1 and/or Hinge Replacement Guide for Andersen 200 Series Basement/Utility Windows Please read this guide completely before starting. For questions about this and other Andersen products, call For the most current version of this guide visit Consult your local building code official for applicable building codes and regulations. Thank you for choosing Andersen products. Please leave this information with homeowner. Parts Included (1) Instruction Guide (12) #8 x 3/4" Recex Head Screw (1) and/or (2) Hinges Supplies Needed Filament or Duct Tape Silicone Sealant Tools Needed Safety Glasses Gloves Square Drill 3/32" Drill Bit Key n A n B Split Arm Hinge n C #8 x 3/4" Recex Head Screw na nb nc Awning 4For old style hinge and/or sash, proceed to page 2. 4For current hinge and/or sash, proceed to page 5. Hopper Hopper orientation shown in this guide Read and follow these warnings during installation. Tape broken glass with filament or duct tape before removing sash to reduce glass fragmentation. Failure to do so may result in severe injury, product and or property damage. Support sash during entire process. will swing freely after screws are removed from hinges and must be supported during screw removal. Failure to support sash may result in injury, product and/or property damage. Use hand screwdrivers. Power screwdrivers may produce too much torque, causing screws to strip Fibrex material. Use a reasonable number of people with sufficient strength when moving and installing units. Always use safe lifting techniques. Failure to do so may result in injury and/or product damage. Follow manufacturer s instructions for safe operation of hand/power tools. Always wear safety glasses. Failure to do so may result in injury and/or product damage. Use caution when working at elevated heights and around unit openings. Follow manufacturer s instructions for safe operation of ladder and/or scaffolding. Failure to do so may result in injury or death. Andersen is a registered trademark of Andersen Corporation. All other marks where denoted are marks of Andersen Corporation Andersen Corporation. All rights reserved. Revised 02/09/06 1

2 Old Style Hinge and/or Replacement 1 Frame 45 2 Open and support sash 45 and remove frame hinge screws. 3 Hinge Remove hinges from sash and dispose of properly. 4 Nylon Receiver Nylon Receiver Remove nylon receivers from sash and dispose of properly. Remove nylon receivers from frame and dispose of properly. 5 Silicone Fill old holes in frame and sash. 2

3 6 7 For sash, remove screws from lock handle and save for reinstallation. Reinstall lock handle at predrilled hole locations, if needed. Do not over tighten screws /16" Tape Measure First Screw Hole Place sash exterior side up. Mark first screw hole 5-7/16" from top of sash down hinge channel as shown. 10 Position hinge with first screw hole over marked location and mark remaining hole. 11 Drill 3/32" Drill Bit Drill holes at marked locations 1/8" deep using 3/32" drill bit. Position hinge over drilled locations and fasten to sash. Do not over tighten screws. 3

4 12 13 Inside Lip 3/32" Drill Bit 1/4" 14 Position hinge channel to bottom of frame (hopper) or top of frame (awning) and tight against inside lip on frame and mark screw locations. Drill holes for hinge channel on frame at marked locations using 3/32" drill bit. 15 Drill Hinge shown for clarity. Shoe Position hinge channel over drilled locations and fasten to frame. Do not over tighten screws. Track Attach sash to frame by sliding hinge shoes into hinge channel tracks on frame. 16 Hinge Pin 17 Hinge Arm Attach hinge arms to hinge pins on frame. Check sash operation. 4

5 Current Style Hinge and/or Replacement 1 Hinge Pin 2 Hinge shown for clarity. Shoe Hinge Arm Track Open sash and pry hinge arms from hinge pins. 3 Slide hinge shoes off hinge channel tracks and remove sash. 4 Remove hinge channels from frame. Remove hinges from sash. 5 6 For sash, remove screws from lock handle and save for reinstallation. 5 Reinstall lock handle at predrilled hole locations, if needed. Do not over tighten screws.

6 7 8 Position hinges over predrilled holes and fasten to sash. Do not over tighten screws. Position hinge channels over predrilled holes and fasten to frame. Do not over tighten screws. 9 Hinge shown for clarity. 10 Hinge Pin Shoe Track Hinge Arm Attach sash to frame by sliding hinge shoes onto hinge channel tracks on frame. Attach hinge arms to channel hinge pins. 11 Check sash operation. 6

Sash Replacement Guide for Andersen Impact Resistant Casement Windows

Sash Replacement Guide for Andersen Impact Resistant Casement Windows Replacement Guide Replacement Guide for Andersen Impact Resistant Casement Windows Congratulations! You have just purchased one of the many fine Andersen products. Proper assembly, installation and maintenance