TK-78K0/KF2+UZ Hard ware Manual

Size: px

Start display at page:

Download "TK-78K0/KF2+UZ Hard ware Manual"

Marcia Lyons
5 years ago
Views:

1 TK-78K0/KF+UZ Hard ware Manual TESSERA TECHNOLOGY INC. 008/6 The nd edition - -

2 Attention The content of this material is a previous notice and might change. The reprint reproduction of this material is prohibited without our approval by the document. Our company doesn't carry the for the mistake of this material at all. Our company doesn't carry the for the violation of the patent, the copyright of the third party generated in relation to the use of our product published in this material, and other intellectual property rights etc. at all. Our company doesn't permit our or third party's any patents, copyrights, and other intellectual property rights based on this material. Information that relates to the circuit, software, and these described to this material explains the operation example and the application example of the semiconductor product. Please go to design customer's equipment in customer's responsibility when you use information on the circuit, software, and these. Our company doesn't carry the for the damage caused in the customer or the third party who originates in these use at all. - -

3 Table of Contents TK-78K0/KF+UZ.... FEATURES.... HARDWARE SPECIFICATION...5. TERMINAL LIST...6 SWITCHES AND LED SW SW5 JP Flash Programming Mode On-chip Debug Mode Normal Operation Mode General purpose setting port.... SW.... SW,SW.... SW LED....6 LED, LED AND LED... POWER SUPPLY...5 TK-78K0/KF+UZ DATA...6. PARTS LAYOUT...6. RF BOARD CONNECTION FIGURE...7. CIRCUIT DIAGRAM OF THE MCU BOARD...8. CIRCUIT DIAGRAM OF THE UZ00 RF BOARD....5 DIMENSION OF THE MCU BOARD

4 TK-78K0/KF+UZ 78K0/KF is the NEC Electronics 8 bit single chip microcomputer. The features and hardware specification of an evaluation board (TK-78K0/KF+UZ MCU board) of 78K0/KF series and mounted UZ00 by Uniband Electronic Corporation are described.. Features Features of the TK-78K0/KF+UZ MCU board are as follows. The evaluation board uses the NEC Electronics 8-bit single chip microcontroller (μpd78f057d). All of ROM,RAM and circumference circuit are efficiently built in one chip on a single board. High-speed operation has been achieved with 6MHz clock. Sub-clock.768KHz standard equipment 8-Kbyte flash memory is built into MCU chip. A high-speed RAM:0 byte and enhancing RAM:6 byte is built into. Hardware is ready to accommodate.ghz transceiver chip UZ00 (IEEE80.5. ZigBee compliant wireless personal area network) made by Uniband Electronic Corporation ( (Attached antenna :Titanis made by Gigaant( 7 I/O ports are equipped at the maximum. MCU board carries a temperature sensor.(s-80c made by SII ) Debugging using on-chip debug function can be done. The board itself is quite and easy to handle; MCU board size 70mm 60mm, The size of including RF transceiver 80mmx60mm. Please inquire direct to the parts maker about specification of UZ00 chip, antenna and temperature sensor. - -

5 . Hardware specification MCU μpd78f057dgk Operation frequency 6MHz Operation (Sub-clock:.768KHz) RF transceiver UZ00 RF Board Interface USB (Mini B connector) RF board connector Connector of board in surrounding(cn: not mounted) Connector of battery(9.0v-6.5v) Operation voltage 5.0V(Supply from USB) 9.0V(Supply from a battely,min.6.5v) - 5 -

6 . Terminal list It is a terminal table of CN, CN and CN of TK-78K0/KF+UZ MCU board. CN terminal list(ffc-0bmep[not mounted] by HONDA CONNECTORS) CN Signal name Terminal MCU name at connection destination +.V P0 P0/SCK0/TxD0 P P/SI0/RxD0 P P/SO0 5 P5 P5/TOH0 6 P6 P6/TOH/INTP5 7 P7 P7/TI50/TO50 8 P P/ANI 9 P5 P5/ANI5 0 P6 P6/ANI6 P7 P7/ANI7 P P/TI5/TO5/INTP P60 P60/SCL0 P6 P6/SDA0 5 P6 P6/EXSCL0 6 P0 P0/INTP0/EXLVI 7 GND GND 8 P0 P0/PCL/INTP6 9 GND GND 0 P P/BUZ/BUSY0/INTP7 Notes 0pin 9pin pin pin CN Pin Configuration - 6 -

7 CN terminal list(tfm-0-0-s-d-a-k-tr[not mounted by SAMTEC ] CN Signal name Terminal MCU name at connection destination Notes GND GND N.C. VREG_EN P50 Output from MCU N.C. 5 RESn P5 Output from MCU 6 FIFO P/TI5/TO50/INTP Input to MCU 7 N.C. 8 FIFOP P5 Input to MCU 9 N.C. 0 CCA P5 Input to MCU N.C. SFD P06/TI0/TO0 Input to MCU N.C. CSn P Output from MCU 5 N.C. 6 SCLK P0/SCK Output from MCU 7 N.C. 8 SI P0/SO Output from MCU 9 GND GND 0 SO P0/SI Input to MCU - 7 -

CN terminal list(tfm-0-0-s-d-a-k-tr[not mounted by SAMTEC ] Terminal MCU name at CN Signal name connection destination TP GND GND TP GND GND 5 TP 6 GND GND 7.

8 CN terminal list(tfm-0-0-s-d-a-k-tr[not mounted by SAMTEC ] Terminal MCU name at CN Signal name connection destination TP GND GND TP GND GND 5 TP 6 GND GND 7.V 8 GND GND 9.V 0 GND GND TP GND GND TP GND GND 5 N.C. 6 GND GND 7 N.C. 8 GND GND 9 N.C. 0 GND GND Notes CN pin pin pin CN pin 9pin 9pin 0pin 0pin CN,CN Pin Configuration - 8 -

Switches and LED. SW SW5 JP Bit-5 of SW is Dip switch for operation mode setting. SW5 is a slide switch to select an operation mode. JP is a jumper to select a power source.

9 Switches and LED. SW SW5 JP Bit-5 of SW is Dip switch for operation mode setting. SW5 is a slide switch to select an operation mode. JP is a jumper to select a power source... Flash Programming Mode Flash EEPROM on the 78K0/KF+ZB MCU can be programmed using the attached software PG-FPL in your PC, which is connected to the MCU board via USB cable, if the following switch and jumper setting is made. Flash programming mode SW Bit Bit Bit Bit Bit 5 SW5 JP ON ON OFF OFF OFF UART USB (-pin short) SW5 SW JP - 9 -

10 .. On-chip Debug Mode The following setting activates the On-chip debug functions on the MCU. On-chip debug mode SW Bit Bit Bit Bit Bit 5 SW5 JP ON ON ON ON ON OCD USB (-pin short).. Normal Operation Mode Please change to the following settings when you execute the program normally. Normal Operation Mode SW Bit Bit Bit Bit Bit 5 SW5 JP OFF OFF OFF OFF OFF UART See below Selection of power source by JP JP select USB Power USB (-pin short) Battery CN (-pin short) - 0 -

11 .. General purpose setting port Bit6-8 of SW is general purpose setting port. It becomes Low if the switch is pushed, and it becomes Open if it separates. Please turn on pull-up resistor (PU0) with built-in MCU when using it. (For more detail of the pull-up resistor, please refer to the User s manual of the μpd78f057 MCU. ) SW terminal list SW Signal Terminal MCU name at name connection destination Bit 6 P00 P00/TI000 Bit 7 P0 P0/TI00/TO00 Bit 8 P05 P05/TI00/SSI Notes - -

12 . SW SW is a directional switch with center push. If it is directed or pushed, the input is set to GND. Otherwise the circuit is open. Therefore please set the on-chip pull-up resistors (PU7) during initializing routine of your program code. (For more detail, please refer to the User s manual of the μpd78f057 MCU.) SW terminal list ( ALPS SKRHADE00) SW Signal Terminal MCU name at name connection destination Notes P7 P7/KR UP P7 P7/KR CENTER PUSH P7 P7/KR LEFT P75 P75/KR5 RIGHT 5 GND GND 6 P76 P76/KR6 DOWN UP LEFT RIGHT DOWN SW Directional switch - -

Therefore please set the on-chip pull-up resistors(pu7) during initializing routine of your program code.

13 . SW,SW SW and SW are tact switches. The port inputs are short-circuited to ground, while they are being pushed, and kept open otherwise. Therefore please set the on-chip pull-up resistors(pu7) during initializing routine of your program code. (For more detail, please refer to the User s manual of the μpd78f057 MCU.) Signal name SW P70 SW P7 SW and SW terminal list (ALPS SKQMBBE00) Terminal MCU name at Notes connection destination P70/KR0 P7/KR SW SW. SW6 SW6 is the reset switch. MCU can be reset by pushing. SW6 - -

14 .5 LED `Power LED. LED is activated when the power supply is turned on..6 LED, LED and LED LED, LED, and LED are available for applications. To make an LED on, please set the output port LOW. LED, LED and LED Terminal list (STANLEY ELECTRIC PGC) Signal name LED P0 LED P LED P Terminal MCU name at connection destination P0 P P Notes LED LED LED - -

15 Power supply There are two choices to supply power to the board, USB or a 006P battery via CN. Please refer to.. JP for the jumper setting. Please replace the battery with a new one, if the voltage level goes down to 6.5V. Below the voltage level of 6.5V, functions of the board are not guaranteed. The battery voltage can be checked at the port as shown below. 9.0V Battery check Signal Terminal MCU name at name connection destination BT_MONI P0/ANI0 Notes.8% of the battery output is available at ANI0. For instance, If the battery level is 9 V, the level of the BT_MONI = V =.0 V If the battery level is 6.5 V, the level of the BT_MONI = V =.97 V - 5 -

16 TK-78K0/KF+UZ Data. Parts Layout CN, CN (RF Board I/F) SW5 (UART/OCD) CN (I/F Expansion) SW (Mode Setting) SW SW6 (Reset SW) SW SW CN (Battery Connector) USB (USB I/F) JP (Power Supply Selection) - 6 -

17 . RF board connection figure - 7 -

18 . Circuit Diagram of the MCU Board C 0.uF P0 P U VOUT VSS NC S-80CNB P00 P0 SI SO SCLK BT_MONI P P5 P6 P7 SI P. SO P. SCLK P. P. P. P. P. RTS_RES0 PORTA PORTB RES_FF0 P. FLMD0 P00 P0 P05 RESET SW CHS-08B RES_K0 P P TP TP R 00K R 0K U C5 0PF Y Y X X XT XT R 00 MC K-A0 C6 0PF TP TP CSTCE6M0V5 R 0K P. XT XT CSn C 0.7uF C 0.uF P0 CSn P P P0 RES_K0 FLMD0 X X P0/INTP0/EXLVI P7 P6 5 P5 6 P 7 P 8 P 9 P 0 P0 RESET P/XT/EXCLKS P/XT FLMD0 5 P/X/EXCLK 6 P/X 7 REGC 8 VSS 9 EVSS 0 E upd78f057dgk P0/PCL/INTP6 P/BUZ/BUSY0/INTP7 P/SCKA0 P/SIA0 P/SOA0 P5/STB0 P00/TI000 P0/TI00/TO00 P0/SO P0/SI P0/SCK P0 P0/ANI0 P/ANI P/ANI P/ANI P/ANI P5/ANI5 P6/ANI6 P7/ANI7 P60/SCL0 P6/SDA0 P6/EXSCL0 P6 P/TI5/TO5/INTP P6 P65 P66 P67 P77/KR7 P76/KR6 P75/KR5 P7/KR P7/KR P7/KR P7/KR P70/KR0 P06/TI0/TO0 P05/TI00/SSI P/INTP/portB AVSS AVREF 58 P57 57 P56 56 P55 55 P5 5 P0/SCK0/TXD0 5 P/SI0/RXD0 5 P/SO0 5 P/TXD6 50 P/RXD6 9 P5/TOH0 8 P6/TOH/INTP5 7 P7/TI50/TO50 6 P0/INTP 5 P5 P5 P5 P50 P/INTP/portA P0 P P P5 P6 P7 FIFOP CCA FIFO RESn VREG_EN P R5 M RXD P. TXD P. FIFOP P. CCA P. FIFO P. RESn P. VREG_EN P. C 0.uF P P5 P7 P5 P7 P60 P6 CN FFC-0BMEP P0 P P6 P P6 P P6 P0 P0 P R6 0 P60 P6 P6 P FLMD0 P76 P75 P7 P7 P7 P7 P70 P05 P LED PGH P. SFD SFD P0 LED R7 P PGH LED 0 R8 P PGH LED 0 R9 CN SB-ZR-SMA-TF R0 M,% USB JP FFC-AMEP U I + C7 0uF/5V LM7MPX-. O G + C8 0uF/5V P7 P7 P7 SW 6 5 SKRHADE00 SW P76 P75 TP5 TP6 PGH 0 BT_MONI P70 R 60K,% P7 SKQMBB SW SKQMBB + C9.7uF/5V Title TK-78K0/KF+ZB Size Document Number Rev A 5E-0A.0 Date: Tuesday, October 0, 005 Sheet of - 8 -

19 USB R 70 USB USB USB 8 U5A 7 SN7LVCG07DCT R K R7 0K R8 0K R9 0K U TXD RXD RTS# CTS# DTR# DSR# DCD# RI# VCC-IO VCC 6 VCC AVCC 0 C 0.uF VOUT 6 USBDM 8 USBDP 7 RSTOUT# 5 XTIN 7 C5 nf R 7 R5 7 R6.5K Y CSTCR6M00G5 L + C0.7uF/5V BLMPG750S USB UX60A-MB-5ST VBUS D- D+ ID_NC 5 GND FG FG FG FG FG FG FG FG C 0.uF C6 0.uF C C 0.uF 0.uF C7 C8 0.uF 0.uF P. RXD TXD P. SW5 5 6 SSSS700 R 00K 8 U5B 5 USB SN7LVCG07DCT R K TXDEN PWREN# PWRCTL TXLED# RXLED# SLEEP# GND GND AGND XTOUT 8 RESET# EECS EESK EEDATA TEST FTBL R0 USB 8 U6A R 7 SN7LVCGDCT USB USB C9 0.uF USB C0 0.uF U7A D CLK CLR PRE VCC Q 5 Q 6 TC7VHCT7AFT R U8 K SN7LVCG5DCK 5 R5 PORTA P. 8 U6B 5 SN7LVCGDCT RTS_RES0 P. U7B D CLK VCC 0 CLR PRE USB Q 9 Q 8 TC7VHCT7AFT 8 U6C 6 SN7LVCGDCT PORTB P. 8 U5C 6 RES_FF0 P. SN7LVCG07DCT SW6 SKQMBB R6 00 RESET0 P. Title TK-78K0/KF+ZB Size Document Number Rev A 5E-0A.0 Date: Tuesday, October 0, 005 Sheet of - 9 -

20 P. P. P. P. P. FIFO FIFOP CCA SFD SO R 0 R7.7K R8.7K R9.7K R0.7K R.7K CN TFM-0-0-S-D-A-K-TR P. P. P. P. P. CSn SCLK SI RESn VREG_EN R 0 CN TFM-0-0-S-D-A-K-TR TP TP TP9 C 0.uF Title TK-78K0/KF+ZB Size Document Number Rev A 5E-0A.0 Date: Tuesday, October 0, 005 Sheet of - 0 -

21 . Circuit Diagram of the UZ00 RF Board CN Tx/EN 6 INT 8 Rx/EN 0 WAKE SEN SCLK 6 SI 8 SO PA/EN RESETN SFM-0-0-S-D-A-K-TR CN 6 5 R CLKOUT_0M(Shield) SFM-0-0-S-D-A-K-TR C 0uF/0V C P Upper side P Lower side C 7pF R M FL T 0MHz Y pf C C5 7pF pf C6 uf C7 7pF CN SMA H C C C 5 C C 0.6pF C 0.5pF L 5.6nH L nh balum matching circuit Characteristic Impedance = 50ohm L 5.6nH C6 0.5pF C7 7pF C8 7pF C8 0.0uF C9 7pF PA/EN Tx/EN C0 80pF _RF RF_P RF_N _RF _GR GND_GR GPIO0 GPIO GPIO5 GPIO LOOP_C 0 _VCO 9 NC 8 _CP 7 6 GND_PLL 5 _PLL XTAL_P U UZ00 XTAL_N _A _BG RX_QP 0 RF_IP 9 XTAL_P 8 XTAL_N 7 CLK_OUT 6 SCAN_M 5 SCAN_EN SPI/IC GND_D _D C 7pF R5 7 R M R 70K Y CLKOUT_0M (Shield) MC-6.768KHz GPIO GPIO RESETn MSEL WAKE INT SO SI SCLK SEN PAD C9 0.0uF UZ (Shield) Rx/EN RESETN WAKE INT SO SI SCLK SEN C pf C5 pf Title UZ00 RF Board Size Document Number Rev A 5E-0A.0 Date: Tuesday, October 7, 006 Sheet of - -

22 .5 Dimension of the MCU Board - -

PCB REV DATE DATE SCH REV 01 JAN JAN 05 wsk START

PCB REV DATE DATE SCH REV 01 JAN JAN 05 wsk START 1 SCH REV PCB REV DATE BY DESCRIPTION PCB REV DATE BY 0.0 01 JAN 0 START 1.0 01 JAN 0 PCB Rev 1 done. 1.0 1.01 1.02 1.0 01 JAN 0 PCB Rev 1 done. 2.0 01 APR 0 01 FEB 02 01 FEB 0 Sheet : Changed CPLD from