PROMAG RWM600A. ISO/IEC15693 Advanced Reader Module. Overview. Features. Application. Specifications. Application Circuit

Transcription

1 Overview ISO569 reader module works with smart label, based on transponders with an operating frequency of.56mhz (e.g. I-CODE SL, Tag-It HF-I etc.), based on TI-RFID technology. Depending on the size of the antenna, the Reader module has a read/write distance up to 00mm. The reader module with small and compact package is designed for installation into other devices, such as printers, terminals and handheld devices. Features. ISO/IEC569 compatible.. Tag Stock Management Technology. (New, Max UID). New Anti-Collision Technology. (New) 4. Configurable parameters for different applications. (New) 5. Support RS485 network. (New) 6. Support all ISO/IEC569 compliant smart labels (Tag-It HF-I, I-CODE SL, LRI5 etc). 7. Operate time < 0ms per one label. 8. Up to 00mm (Max. 0.W) with correct antenna. 9. Small package module (DIP8) 0. 0 Programmable I/O, D/O and IRQ for OEM.. RF parameters configurable. In-System Programmable firmware for OEM/ODM. Application. EPC Supply Chain. EPC for Retail system. Logistics Control System 4. Express Parcel Management. 5. Product Authentication. 6. Access Control / Time Recorder. 7. Books / Documents Tracking. 8. Ticketing. 9. Smart Label printer and encoder. Specifications. Power 5VDC (Standby: 00mA). Max 0. Watt RF output. (Max 00mm RF Distance). RF Protocol: ISO569 out of RF Modulation/Subcarrier: 00% / FM. 5. Serial interface (UART TTL : 900,n,8,) Application Circuit

2 Block Diagram TX.56MHz Transceiver ISO569 MCU Serial I/F PIO RX IRQ Specifications Parameter Condition Min Type Max Unit Supply voltage (DC) Vcc to GND V Supply ripple See note 40 mvpp Stand-by current consumption Vcc = 5V, with Start Kit 00 ma Max peak voltage applied on drain of V output transistor Output power operation 00 mw Amplitude modulation depth in 0% mode 0% % 6% Minimum depth for 00% ASK 40 db Note:. The maximum ripple current could result in a 0% reduction of the reading distance.. Modulation mode: Two subcarrier (FM) or One subcarrier (AM) selectable. (Default FM).. Modulation depth: 0% or 00% selectable. (Default 00%)

3 Dimension (DIP8 Package) Unit: mm PIN Assignment PIN# Name I/O Type Description ~8 PIO 0~7 I/O Reserve 9 DO Output Digital Output 0 DO Output Digital Output TXEN Output RS485 TXEN Control /RST Input External Reset IRQ Input Interrupt Request (Falling Edge) 4 GND Input Power Ground 5 VCC Input Power Input 5VDC 6 TXD Output Serial Output (UART TTL) 7 RXD Input Serial Input (UART TTL) 8~5 NC No Connect 6 RF_RX Input RF Antenna Input 7 RF_GND Output RF Antenna Ground 8 RF_TX Output RF Antenna Output PIO Default PIN# Name I/O Type Description 5 PIO 4 Output Buzzer 6 PIO 5 Output Green LED 7 PIO 6 Output Red LED 8 PIO 7 Output Orange LED

4 SK Introduction The SK is for you to study the reader module and to learn the ISO/IEC569 operation, and for you to design your software for your application. The SK include a changeable antenna to help you to design a new and different antenna. It also can be integrate into your RFID system. WAS-404 PIN# FROM PC COM PORT 9VDC " " " "

5 SK Circuit Diagram C6.5pF C7 ANT L=.5uH / Q=5 C.7pF C 7pF 0pF JP BUZZER LED_GRN LED_RED LED_ORG TXEN /RST U PIO 0 PIO PIO PIO PIO 4 PIO 5 PIO 6 PIO 7 DO DO PIO 8 PIO 9 IRQ GND RF_TX RF_GND RF_RX RWM RXD TXD VCC HEADER 4 RWM RF_TX RF_RX RXD TXD C4 0.uF C5 uf/6v R6 RF_RX L4 L5.K L6 C8 0.uH 5.6uH R8 C9 C0 0nF K RF_TX TXD R7 Q MMBT906 Open 56pF R0 4.7K K C uf R K LED_ORG D R R 00K D BAS6 ADL-4S70 D ADL-5S75 0 R6 0 BU BUZZER RXD Q5 MMBT904 R4 K R7 0K D6 R8 BZR07 D5 BAS6 ADL-S7 0 C6 00n OPEN f or VCC=V, 0 ohm f or VCC=5V R9 0 U4 AICS-78D05A OUT D7 BAS6 IN C7 00n VCC C8 00u/5V J DC POWER JACK P FEMALE DB9 TX RX GND.56 MHz Antenna HISTORY REV.G: (005//5). Change L4=0, L5=.uH, L6=5.6uH. Change C+C=9.7pF REV.F: (005/0/7). Remove L4, L5, L6 and short by 0 ohm. Change C6, C7, C, C value CABLE / 50 ohm POWER Filter RS LED_GRN Q4 MMBT906 D4 BAS6 R5 0K LED_RED TO-5 D8 SD RX TX

6 LED Status LED Blink ON OFF Orange RF Field Working RF Field Power OFF Initialization Red Communication Green Tag In RF field No Tag Tag Compatibility ISO569 Manufacture Product Memory (bits) Anti-Collision Read Write Texas Instruments Tag-it HF-I 048 Yes Yes Yes Philips I-Code SL 04 Yes Yes Yes Infineon my-d SRF55V0P 500 Yes Yes Yes Infineon my-d SRF55V0S 500 Yes Id Only No Infineon my-d SRF55V0P Yes Yes Yes Infineon my-d SRF55V0S Yes Id Only No ST Micro LRI5 5 Yes Yes Yes

7 Order Information Part Number Contents Description Reader Module SK + Start Kit + SDK CD + Tag-It HF-I x Starter Development Kit Note: The ISO569 Demo Software was included in SDK CD of SK only.