CMOS, Rail-to-Rail, I/O OPERATIONAL AMPLIFIERS

Transcription

1 OPA73 OPA73 OPA73 OPA73 OPA73 OPA273 OPA473 OPA74 OPA274 OPA474 SBOS8A MARCH 2 CMOS, Rail-to-Rail, I/O OPERATIONAL AMPLIFIERS FEATURES RAIL-TO-RAIL INPUT AND OUTPUT WIDE SUPPLY RANGE: Single Supply: 4V to 2V Dual Supplies: ±2 to ±6 LOW QUIESCENT CURRENT: 6µA FULL-SCALE CMRR: 9dB LOW OFFSET: 6µV HIGH SPEED: OPA73: MHz,.6V/µs OPA74: 3MHz, 3V/ µs MicroSIZE PACKAGES: SOT23-5, MSOP-8, TSSOP-4 LOW INPUT BIAS CURRENT: pa APPLICATIONS AUTOMOTIVE APPLICATIONS: Audio, Sensor Applications, Security Systems PORTABLE EQUIPMENT ACTIVE FILTERS TRANSDUCER AMPLIFIER TEST EQUIPMENT NC DATA ACQUISITION Out V +In 2 3 OPA73 OPA74 SOT V+ In Out A In A +In A V OPA273 OPA274 A B In +In V MSOP-8, SO-8, DIP V+ DESCRIPTION The OPA73 and OPA74 series op amps are optimized for applications requiring rail-to-rail input and output swing. Single, dual, and quad versions are offered in a variety of packages. While the quiescent current is less than 2µA per amplifier, the OPA73 still offers excellent dynamic performance (MHz GBW and.6v/µs SR) and unity-gain stability. The OPA74 is optimized for gains of 5 or greater and provides 3MHz GBW and 3V/µs slew rate. The OPA73 and OPA74 series are fully specified and guaranteed over the supply range of ±2V to ±6V. Input swing extends 3mV beyond the rail and the output swings to within 4mV of the rail. The single versions (OPA73 and OPA74) are available in the MicroSIZE SOT23-5 and in the standard SO-8 surfacemount, as well as the DIP-8 packages. Dual versions (OPA273 and OPA274) are available in the MSOP-8, SO-8, and DIP-8 packages. The quad OPA473 and OPA474 are available in the TSSOP-4 and SO-4 packages. All are specified for operation from 4 C to +85 C. OPA73 OPA74 SO-8, DIP-8 Out B In B +In B NC V+ Out NC Out A In A +In A V+ +In B In B Out B A B OPA473 OPA474 D C TSSOP-4, SO Out D In D +In D V +In C In C Out C Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright 2, Texas Instruments Incorporated

2 ABSOLUTE MAXIMUM RATINGS () Supply Voltage, V+ to V V Signal Input Terminals, Voltage (2)... (V ).3V to (V+) +.3V Current (2)... ma Output Short-Circuit (3)... Continuous Operating Temperature C to +25 C Storage Temperature C to +5 C Junction Temperature C Lead Temperature (soldering, s) C NOTES: () Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. (2) Input terminals are diode-clamped to the power supply rails. Input signals that can swing more than.3v beyond the supply rails should be current-limited to ma or less. (3) Short-circuit to ground, one amplifier per package. ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. PACKAGE/ORDERING INFORMATION MINIMUM PACKAGE RECOMMENDED DRAWING PACKAGE ORDERING TRANSPORT PRODUCT DESCRIPTION GAIN PACKAGE NUMBER MARKING NUMBER () MEDIA OPA73NA Single, GBW = MHz SOT A3 OPA73NA/25 Tape and Reel " " " " " " OPA73NA/3K Tape and Reel OPA73UA Single, GBW = MHz SO-8 82 OPA73UA OPA73UA Rails " " " " " " OPA73UA/2K5 Tape and Reel OPA73PA Single, GBW = MHz DIP-8 6 OPA73PA OPA73PA Rails OPA273EA Dual, GBW = MHz MSOP B3 OPA273EA/25 Tape and Reel " " " " " " OPA273EA/2K5 Tape and Reel OPA273UA Dual, GBW = MHz SO-8 82 OPA273UA OPA273UA Rails " " " " " " OPA273UA/2K5 Tape and Reel OPA273PA Dual, GBW = MHz DIP-8 6 OPA273PA OPA273PA Rails OPA473EA Quad, GBW = MHz TSSOP OPA473EA OPA473EA/25 Tape and Reel " " " " " " OPA473EA/2K5 Tape and Reel OPA473UA Quad, GBW = MHz SO OPA473UA OPA473UA Rails " " " " " " OPA473UA/2K5 Tape and Reel OPA74NA Single, GBW = 5MHz 5 SOT A4 OPA74NA/25 Tape and Reel " " " " " " OPA74NA/3K Tape and Reel OPA74UA Single, GBW = 5MHz 5 SO-8 82 OPA74UA OPA74UA Tape and Reel " " " " " " OPA74UA/2K5 Tape and Reel OPA74PA Single, GBW = 5MHz 5 DIP-8 6 OPA74PA OPA74PA Rails OPA274EA Dual, GBW = 5MHz 5 MSOP B4 OPA273EA/25 Tape and Reel " " " " " " OPA273EA/2K5 Tape and Reel OPA274UA Dual, GBW = 5MHz 5 SO-8 82 OPA274UA OPA274UA Rails " " " " " " OPA274UA/2K5 Tape and Reel OPA274PA Dual, GBW = 5MHz 5 DIP-8 6 OPA274PA OPA274PA Rails OPA474EA Quad, GBW = 5MHz 5 TSSOP OPA474EA OPA474EA/25 Tape and Reel " " " " " " OPA474EA/2K5 Tape and Reel OPA474UA Quad, GBW = 5MHz 5 SO OPA474UA OPA474UA Rails " " " " " " OPA474UA/2K5 Tape and Reel NOTE: () Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /3K indicates 3 devices per reel). Ordering 3 pieces of OPA73NA/3K will get a single 3-piece Tape and Reel. 2 OPA73, OPA74 SBOS8A

3 OPA73 ELECTRICAL CHARACTERISTICS: V S = 4V to 2V Boldface limits apply over the specified temperature range, T A = 4 C to +85 C At T A = +25 C, R L = 2kΩ connected to V S / 2 and V OUT = V S / 2, unless otherwise noted. OPA73NA, UA, PA OPA273EA, UA, PA OPA473EA, UA PARAMETER CONDITION MIN TYP MAX UNITS OFFSET VOLTAGE Input Offset Voltage V OS V S = ±5V, V CM = V ±6 ±75 µv Drift dv OS /dt T A = 4 C to +85 C ±4 µv/ C vs Power Supply PSRR V S = ±2V to ±6V, V CM = V 2 µv/v Over Temperature V S = ±2V to ±6V, V CM = V 2 µv/v Channel Separation, dc R L = 2kΩ µv/v f = khz 98 db INPUT VOLTAGE RANGE Common-Mode Voltage Range V CM (V ).3 (V+) +.3 V Common-Mode Rejection Ratio CMRR V S = ±5V, (V ).3V < V CM < (V+) +.3V 7 9 db over Temperature V S = ±5V, (V ) < V CM < (V+) 68 db V S = ±5V, (V ).3V < V CM < (V+) 2V 8 96 db over Temperature V S = ±5V, (V ) < V CM < (V+) 2V 74 db INPUT BIAS CURRENT Input Bias Current I B V S = ±5V, V CM = V ± ± pa Input Offset Current I OS V S = ±5V, V CM = V ±.5 ± pa INPUT IMPEDANCE Differential Ω pf Common-Mode Ω pf NOISE Input Voltage Noise, f =.Hz to Hz V S = ±5V, V CM = V 6 µvp-p Input Voltage Noise Density, f = khz e n V S = ±5V, V CM = V 45 nv/ Hz Current Noise Density, f = khz i n V S = ±5V, V CM = V 2.5 fa/ Hz OPEN-LOOP GAIN Open-Loop Voltage Gain A OL R L = kω, (V )+.V < V O < (V+).V 2 db R L = 2kΩ, (V )+.75V < V O < (V+).75V db over Temperature R L = 2kΩ, (V )+.75V < V O < (V+).75V 96 db R L = 5kΩ, (V )+.5V < V O < (V+).5V db over Temperature R L = 5kΩ, (V )+.5V < V O < (V+).5V 96 db OUTPUT Voltage Output Swing from Rail R L = kω, A OL > 8dB 4 mv R L = 2kΩ, A OL > db 75 mv over Temperature R L = 2kΩ, A OL > 96dB 75 mv R L = 5kΩ, A OL > db 5 mv over Temperature R L = 5kΩ, A OL > 96dB 5 mv Output Current I OUT V S V OUT < V ± ma Short-Circuit Current I SC ±4 ma Capacitive Load Drive C LOAD See Typical Performance Curves FREQUENCY RESPONSE C L = pf Gain-Bandwidth Product GBW G = + MHz Slew Rate SR V S = ±5V, G = +.6 V/µs Settling Time,.% t S V S = ±5V, 5V Step, G = + 5 µs.% V S = ±5V, 5V Step, G = + 2 µs Overload Recovery Time V IN Gain = V S 3 µs Total Harmonic Distortion + Noise THD+N V S = ±5V, V O = 3Vp-p, G = +, f = khz.2 % POWER SUPPLY Specified Voltage Range, Single Supply V S 4 2 V Specified Voltage Range, Dual Supplies V S ±2 ±6 V Operating Voltage Range 3.6 to 2 V Quiescent Current (per amplifier) I Q I O = 6 2 µa over Temperature 3 µa TEMPERATURE RANGE Specified Range 4 85 C Operating Range C Storage Range 65 5 C Thermal Resistance θ JA SOT23-5 Surface-Mount 2 C/W MSOP-8 Surface-Mount 5 C/W TSSOP-4 Surface-Mount C/W SO-8 Surface Mount 5 C/W SO-4 Surface Mount C/W DIP-8 C/W OPA73, OPA74 3 SBOS8A

4 OPA74 ELECTRICAL CHARACTERISTICS: V S = 4V to 2V Boldface limits apply over the specified temperature range, T A = 4 C to +85 C At T A = +25 C, R L = 2kΩ connected to V S / 2 and V OUT = V S / 2, unless otherwise noted. OPA74NA, UA, PA OPA274EA, UA, PA OPA474EA, UA PARAMETER CONDITION MIN TYP MAX UNITS OFFSET VOLTAGE Input Offset Voltage V OS V S = ±5V, V CM = V ±6 ±75 µv Drift dv OS /dt T A = 4 C to +85 C ±4 µv/ C vs Power Supply PSRR V S = ±2V to ±6V, V CM = V 2 µv/v Over Temperature V S = ±2V to ±6V, V CM = V 2 µv/v Channel Separation, dc R L = 2kΩ µv/v f = khz 98 db INPUT VOLTAGE RANGE Common-Mode Voltage Range V CM (V ).3 (V+) +.3 V Common-Mode Rejection Ratio CMRR V S = ±5V, (V ).3V < V CM < (V+) +.3V 7 9 db over Temperature V S = ±5V, (V ) < V CM < (V+) 68 db V S = ±5V, (V ).3V < V CM < (V+) 2V 8 96 db over Temperature V S = ±5V, (V ) < V CM < (V+) 2V 74 db INPUT BIAS CURRENT Input Bias Current I B V S = ±5V, V CM = V ± ± pa Input Offset Current I OS V S = ±5V, V CM = V ±.5 ± pa INPUT IMPEDANCE Differential Ω pf Common-Mode Ω pf NOISE Input Voltage Noise, f =.Hz to Hz V S = ±5V, V CM = V 6 µvp-p Input Voltage Noise Density, f = khz e n V S = ±5V, V CM = V 45 nv/ Hz Current Noise Density, f = khz i n V S = ±5V, V CM = V 2.5 fa/ Hz OPEN-LOOP GAIN Open-Loop Voltage Gain A OL R L = kω, (V )+.V < V O < (V+).V 2 db R L = 2kΩ, (V )+.75V < V O < (V+).75V db over Temperature R L = 2kΩ, (V )+.75V < V O < (V+).75V 96 db R L = 5kΩ, (V )+.5V < V O < (V+).5V db over Temperature R L = 5kΩ, (V )+.5V < V O < (V+).5V 96 db OUTPUT Voltage Output Swing from Rail R L = kω, A OL > 8dB 4 mv R L = 2kΩ, A OL > db 75 mv over Temperature R L = 2kΩ, A OL > 96dB 75 mv R L = 5kΩ, A OL > db 5 mv over Temperature R L = 5kΩ, A OL > 96dB 5 mv Output Current I OUT V S V OUT < V ± ma Short-Circuit Current I SC ±4 ma Capacitive Load Drive C LOAD See Typical Performance Curves FREQUENCY RESPONSE C L = pf Gain-Bandwidth Product GBW G = +5 3 MHz Slew Rate SR V S = ±5V, G = +5 3 V/µs Settling Time,.% t S V S = ±5V, 5V Step, G = +5 8 µs.% V S = ±5V, 5V Step, G = +5 2 µs Overload Recovery Time V IN Gain = V S.6 µs Total Harmonic Distortion + Noise THD+N V S = ±5V, V O = 3Vp-p, G = +5, f = khz.25 % POWER SUPPLY Specified Voltage Range, Single Supply V S 4 2 V Specified Voltage Range, Dual Supplies V S ±2 ±6 V Operating Voltage Range 3.6 to 2 V Quiescent Current (per amplifier) I Q I O = 6 2 µa over Temperature 3 µa TEMPERATURE RANGE Specified Range 4 85 C Operating Range C Storage Range 65 5 C Thermal Resistance θ JA SOT23-5 Surface-Mount 2 C/W MSOP-8 Surface-Mount 5 C/W TSSOP-4 Surface-Mount C/W SO-8 Surface Mount 5 C/W SO-4 Surface Mount C/W DIP-8 C/W 4 OPA73, OPA74 SBOS8A

5 TYPICAL CHARACTERISTICS At T A = +25 C, V S = ±5V, and R L = 2kΩ, unless otherwise noted. 2 OPA73 GAIN AND PHASE vs FREQUENCY 2 2 OPA74 GAIN AND PHASE vs FREQUENCY Gain (db) Phase ( ) Gain (db) Phase ( ) k k k M M 4 4 k k k M M Frequency (Hz) Frequency (Hz) 2 CMRR vs FREQUENCY 4 PSRR vs FREQUENCY CMRR Limited Range 2 8 CMRR (db) 6 4 CMRR Full Scale PSRR (db) k k k M k k k M Frequency (Hz) Frequency (Hz) 7 6 MAXIMUM AMPLITUDE vs FREQUENCY (V+) (V ) = 2V 6 4 CHANNEL SEPARATION vs FREQUENCY Amplitude (V) OPA73 OPA74 Channel Separation (db) k k k M M k k k M Frequency (Hz) Frequency (Hz) OPA73, OPA74 5 SBOS8A

6 TYPICAL CHARACTERISTICS (Cont.) At T A = +25 C, V S = ±5V, and R L = 2kΩ, unless otherwise noted. INPUT CURRENT AND VOLTAGE SPECTRAL NOISE vs FREQUENCY 2 COMMON-MODE REJECTION RATIO vs TEMPERATURE Input Current and Voltage Spectral Noise nv/ Hz Voltage Noise Current Noise Output Current Spectral Noise fa/ Hz CMRR (db) Limited Scale Full Scale... k k k M Frequency (Hz) Temperature ( C) 4 OPEN-LOOP GAIN vs TEMPERATURE INPUT BIAS (I B ) AND OFFSET (I OS ) CURRENT vs TEMPERATURE A OL (db) 3 2 Bias Current (pa). I B I OS Temperature ( C) Temperature ( C) QUIESCENT CURRENT vs TEMPERATURE 2 PSRR vs TEMPERATURE 2 I Q (µa) 5 PSRR (db) Temperature ( C) Temperature ( C) 6 OPA73, OPA74 SBOS8A

7 TYPICAL CHARACTERISTICS (Cont.) At T A = +25 C, V S = ±5V, and R L = 2kΩ, unless otherwise noted.. TOTAL HARMONIC DISTORTION PLUS NOISE (Load = 5kΩ, BW = 8kHz,.Vrms) 5 INPUT BIAS CURRENT (I B ) vs COMMON-MODE VOLTAGE (V CM ) TEMPERATURE = 25C THD (%).. G = +5 OPA74 OPA73 G = + Input Bias Current (pa) 5 5. k k k Frequency (Hz) Common-Mode Voltage, V CM (V) 5 INPUT BIAS CURRENT (I B ) vs COMMON-MODE VOLTAGE (V CM ) TEMPERATURE = 25 C 2 QUIESCENT CURRENT vs SUPPLY VOLTAGE Input Bias Current (na) 5 5 Quiescent Current (µa) Common-Mode Voltage, V CM (V) Supply Voltage (V) Short-Circuit Current (ma) SHORT-CIRCUIT CURRENT vs SUPPLY VOLTAGE I SC N (Sinking) I SC P (Sourcing) Supply Voltage (V) Output Voltage (V) OUTPUT VOLTAGE SWING vs OUTPUT CURRENT Sourcing Sinking +25 C +25 C +25 C +25 C 55 C 55 C Output Current (±ma) OPA73, OPA74 7 SBOS8A

8 TYPICAL CHARACTERISTICS (Cont.) At T A = +25 C, V S = ±5V, and R L = 2kΩ, unless otherwise noted. 9 8 OPA73 SMALL-SIGNAL OVERSHOOT (%) vs CAPACITIVE LOAD AND GAIN G = OPA74 SMALL-SIGNAL OVERSHOOT (%) vs CAPACITIVE LOAD 7 7 Overshoot (%) G = Overshoot (%) G = +5 2 G = +5 2 k k k k Load Capacitance Value (pf) Capacitance Load (pf) OPA73 SETTLING TIME vs GAIN 5 OPA74 SETTLING TIME vs GAIN Settling Time (µs) %.% Settling Time (µs) %.% Non-Inverting Gain (V/V) Non-Inverting Gain (V/V) 25 V OS PRODUCTION DISTRIBUTION 25 V OS DRIFT PRODUCTION DISTRIBUTION 2 2 Frequency (%) 5 Frequency (%) <. <.5 <.3 <.45 <.6 < < < 3 < 6 < 9 < 2 < 5 < 8 < 2 < 24 < 27 < 3 > 3 Voltage Offset (µv) Voltage Offset (µv/ C) 8 OPA73, OPA74 SBOS8A

9 TYPICAL CHARACTERISTICS (Cont.) At T A = +25 C, V S = ±5V, and R L = 2kΩ, unless otherwise noted. OPA73 SMALL SIGNAL STEP RESPONSE (G = +V/V, R L = 2kΩ, C L = pf) OPA74 SMALL SIGNAL STEP RESPONSE (G = +5V/V, C F = 3pF, R F = kω, C L = pf, R L = 2kΩ,) 5mV/div 5mV/div 5µs/div 5µs/div OPA73 LARGE SIGNAL STEP RESPONSE (G = +V/V, R L = 2kΩ, C L = pf) OPA74 LARGE SIGNAL STEP RESPONSE (G = +5V/V, R L = 2kΩ, C F = 3pF, C L = pf) V/div V/div µs/div 2µs/div OPA73, OPA74 9 SBOS8A

10 APPLICATIONS INFORMATION OPA73 and OPA74 series op amps can operate on 6µA quiescent current from a single (or split) supply in the range of 4V to 2V (±2V to ±6V), making them highly versatile and easy to use. The OPA73 is unity-gain stable and offers MHz bandwidth and.6v/µs slew rate. The OPA74 is optimized for gains of 5 or greater with a 3MHz bandwidth and 3V/µs slew rate. Rail-to-rail input and output swing helps maintain dynamic range, especially in low supply applications. Figure shows the input and output waveforms for the OPA73 in unitygain configuration. Operation is from a ±5V supply with a kω load connected to V S /2. The input is a Vp-p sinusoid. Output voltage is approximately Vp-p. 2.V/div Input Output (inverted on scope) 2µs/div G = +, V S = ±5V Power-supply pins should be bypassed with pf ceramic capacitors in parallel with µf tantalum capacitors. OPERATING VOLTAGE OPA73 and OPA74 series op amps are fully specified and guaranteed from +4V to +2V over a temperature range of 4ºC to +85ºC. Parameters that vary significantly with operating voltages or temperature are shown in the Typical Performance Curves. RAIL-TO-RAIL INPUT The input common-mode voltage range of the OPA73 series extends 3mV beyond the supply rails at room temperature. This is achieved with a complementary input stage an N- channel input differential pair in parallel with a P-channel differential pair, as shown in Figure 2. The N-channel pair is active for input voltages close to the positive rail, typically (V+) 2.V to 3mV above the positive supply, while the P- channel pair is on for inputs from 3mV below the negative supply to approximately (V+).5V. There is a small transition region, typically (V+) 2.V to (V+).5V, in which both pairs are on. This 5mV transition region can vary ±mv with process variation. Thus, the transition region (both stages on) can range from (V+) 2.V to (V+).4V on the low end, up to (V+).9V to (V+).6V on the high end. Within the 5mV transition region PSRR, CMRR, offset voltage, and offset drift, and THD may vary compared to operation outside this region. FIGURE. Rail-to-Rail Input and Output. V+ V O V IN + V IN V FIGURE 2. Simplified Schematic. OPA73, OPA74 SBOS8A

11 INPUT VOLTAGE Device inputs are protected by ESD diodes that will conduct if the input voltages exceed the power supplies by more than approximately 3mV. Momentary voltages greater than 3mV beyond the power supply can be tolerated if the current is limited to ma. This is easily accomplished with an input resistor, as shown in Figure 3. Many input signals are inherently current-limited to less than ma; therefore, a limiting resistor is not always required. The OPA73 features no phase inversion when the inputs extend beyond supplies if the input current is limited, as seen in Figure 4. CAPACITIVE LOAD AND STABILITY The OPA73 and OPA74 series op amps can drive up to pf pure capacitive load. Increasing the gain enhances the amplifier s ability to drive greater capacitive loads (see the typical performance curve Small Signal Overshoot vs Capacitive Load ). One method of improving capacitive load drive in the unitygain configuration is to insert a Ω to 2Ω resistor inside the feedback loop, as shown in Figure 5. This reduces ringing with large capacitive loads while maintaining DC accuracy. I OVERLOAD ma max +V OPA73 V OUT V IN OPA73 R S 2Ω V OUT V IN R V C L R L FIGURE 3. Input Current Protection for Voltages Exceeding the Supply Voltage. 2.V/div 2µs/div V S = ±5.V, V IN = Vp-p FIGURE 4. OPA73 No Phase Inversion with Inputs Greater than the Power-Supply Voltage. RAIL-TO-RAIL OUTPUT A class AB output stage with common-source transistors is used to achieve rail-to-rail output. This output stage is capable of driving kω loads connected to any point between V+ and ground. For light resistive loads (> kω), the output voltage can swing to 4mV from the supply rail. With moderate resistive loads (2kΩ), the output can swing to within 75mV from the supply rails while maintaining high open-loop gain (see the typical performance curve Output Voltage Swing vs Output Current ). FIGURE 5. Series Resistor in Unity-Gain Buffer Configuration Improves Capacitive Load Drive. APPLICATION CIRCUITS Figure 6 shows a G = 5 non-inverting amplifier implemented with the OPA73 and OPA74 op amps. It demonstrates the increased speed characteristics (bandwidth, slew rate and settling time) that can be achieved with the OPA74 family when used in gains of five or greater. Some optimization of feedback capacitor value may be required to achieve best dynamic response. Circuits with closed-loop gains of less than five should use the OPA73 family for good stability and capacitive load drive. The OPA73 can be used in gains greater than five, but will not provide the increased speed benefits of the OPA74 family. The OPA73 series op amps are optimized for driving medium-speed sampling data converters. The OPA73 op amps buffer the converter s input capacitance and resulting charge injection while providing signal gain. Figure 7 shows the OPA273 in a dual-supply buffered reference configuration for the DAC7644. The DAC7644 is a 6-bit, low-power, quad-voltage output converter. Small size makes the combination ideal for automatic test equipment, data acquisition systems, and other low-power spacelimited applications. OPA73, OPA74 SBOS8A

12 3pF 5kΩ 2kΩ 5kΩ 2kΩ OPA73 OPA74 V IN G = 5 V IN G = 5 LARGE-SIGNAL RESPONSE Demonstrates speed improvement that can be achieved with OPA74 family in applications with G 5. 2V/div OPA73 OPA74 5µs/div FIGURE 6. OPA74 Provides higher Speed in G 5. DAC7644 NC NC NC NC 45 +V V OUT A Sense 44 V OUT A 43 V OUT V V REF L AB Sense V REF L AB V REF H AB pF /2 OPA V Ref Negative Reference V REF H AB Sense 39 V+ V OUT B Sense V OUT B V OUT 5pF /2 OPA V Ref Positive Reference V FIGURE 7. OPA73 as Dual Supply Configuration-Buffered References for the DAC OPA73, OPA74 SBOS8A

13 PACKAGE OPTION ADDENDUM 28-Aug-28 PACKAGING INFORMATION Orderable Device Status () Package Type Package Drawing Pins Package Qty OPA273EA/25 ACTIVE MSOP DGK 8 25 Green (RoHS & OPA273EA/25G4 ACTIVE MSOP DGK 8 25 Green (RoHS & OPA273EA/2K5 ACTIVE MSOP DGK 8 25 Green (RoHS & OPA273EA/2K5G4 ACTIVE MSOP DGK 8 25 Green (RoHS & OPA273PA ACTIVE PDIP P 8 5 Green (RoHS & OPA273PAG4 ACTIVE PDIP P 8 5 Green (RoHS & OPA273UA ACTIVE SOIC D 8 Green (RoHS & OPA273UA/2K5 ACTIVE SOIC D 8 25 Green (RoHS & OPA273UA/2K5G4 ACTIVE SOIC D 8 25 Green (RoHS & OPA273UAG4 ACTIVE SOIC D 8 Green (RoHS & OPA274EA/25 ACTIVE MSOP DGK 8 25 Green (RoHS & OPA274EA/25G4 ACTIVE MSOP DGK 8 25 Green (RoHS & OPA274PA ACTIVE PDIP P 8 5 Green (RoHS & OPA274PAG4 ACTIVE PDIP P 8 5 Green (RoHS & OPA274UA ACTIVE SOIC D 8 Green (RoHS & OPA274UA/2K5 ACTIVE SOIC D 8 25 Green (RoHS & OPA274UA/2K5G4 ACTIVE SOIC D 8 25 Green (RoHS & OPA274UAG4 ACTIVE SOIC D 8 Green (RoHS & OPA473EA/25 ACTIVE TSSOP PW 4 25 Green (RoHS & OPA473EA/25G4 ACTIVE TSSOP PW 4 25 Green (RoHS & OPA473EA/2K5 ACTIVE TSSOP PW 4 25 Green (RoHS & OPA473EA/2K5G4 ACTIVE TSSOP PW 4 25 Green (RoHS & OPA473UA ACTIVE SOIC D 4 58 Green (RoHS & OPA473UA/2K5 ACTIVE SOIC D 4 25 Green (RoHS & OPA473UA/2K5G4 ACTIVE SOIC D 4 25 Green (RoHS & Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3) N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type Addendum-Page

14 PACKAGE OPTION ADDENDUM 28-Aug-28 Orderable Device Status () Package Type Package Drawing Pins Package Qty OPA473UAG4 ACTIVE SOIC D 4 58 Green (RoHS & OPA474EA/25 ACTIVE TSSOP PW 4 25 Green (RoHS & OPA474EA/25G4 ACTIVE TSSOP PW 4 25 Green (RoHS & OPA474EA/2K5 ACTIVE TSSOP PW 4 25 Green (RoHS & OPA474EA/2K5G4 ACTIVE TSSOP PW 4 25 Green (RoHS & OPA474UA ACTIVE SOIC D 4 58 Green (RoHS & OPA474UAG4 ACTIVE SOIC D 4 58 Green (RoHS & OPA73NA/25 ACTIVE SOT-23 DBV 5 25 Green (RoHS & OPA73NA/25G4 ACTIVE SOT-23 DBV 5 25 Green (RoHS & OPA73NA/3K ACTIVE SOT-23 DBV 5 3 Green (RoHS & OPA73NA/3KG4 ACTIVE SOT-23 DBV 5 3 Green (RoHS & OPA73PA ACTIVE PDIP P 8 5 Green (RoHS & OPA73PAG4 ACTIVE PDIP P 8 5 Green (RoHS & OPA73UA ACTIVE SOIC D 8 Green (RoHS & OPA73UA/2K5 ACTIVE SOIC D 8 25 Green (RoHS & OPA73UA/2K5G4 ACTIVE SOIC D 8 25 Green (RoHS & OPA73UAG4 ACTIVE SOIC D 8 Green (RoHS & OPA74NA/25 ACTIVE SOT-23 DBV 5 25 Green (RoHS & OPA74NA/25G4 ACTIVE SOT-23 DBV 5 25 Green (RoHS & OPA74NA/3K ACTIVE SOT-23 DBV 5 3 Green (RoHS & OPA74NA/3KG4 ACTIVE SOT-23 DBV 5 3 Green (RoHS & OPA74PA ACTIVE PDIP P 8 5 Green (RoHS & OPA74PAG4 ACTIVE PDIP P 8 5 Green (RoHS & OPA74UA ACTIVE SOIC D 8 Green (RoHS & OPA74UA/2K5 ACTIVE SOIC D 8 25 Green (RoHS & OPA74UA/2K5G4 ACTIVE SOIC D 8 25 Green (RoHS & Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3) N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type Addendum-Page 2

15 PACKAGE OPTION ADDENDUM 28-Aug-28 Orderable Device Status () Package Type Package Drawing Pins Package Qty OPA74UAG4 ACTIVE SOIC D 8 Green (RoHS & Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3) () The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & - please check for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed.% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either ) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & : TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed.% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3

16 PACKAGE MATERIALS INFORMATION 2-Dec-28 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Reel Reel Diameter Width (mm) W (mm) A (mm) B (mm) K (mm) P (mm) OPA273EA/25 MSOP DGK Q OPA273EA/2K5 MSOP DGK Q OPA273UA/2K5 SOIC D Q OPA274EA/25 MSOP DGK Q OPA274UA/2K5 SOIC D Q OPA473EA/25 TSSOP PW Q OPA473EA/2K5 TSSOP PW Q OPA473UA/2K5 SOIC D Q OPA474EA/25 TSSOP PW Q OPA474EA/2K5 TSSOP PW Q OPA73NA/25 SOT-23 DBV Q3 OPA73NA/3K SOT-23 DBV Q3 OPA73UA/2K5 SOIC D Q OPA74NA/25 SOT-23 DBV Q3 OPA74NA/3K SOT-23 DBV Q3 OPA74UA/2K5 SOIC D Q W (mm) Pin Quadrant Pack Materials-Page

17 PACKAGE MATERIALS INFORMATION 2-Dec-28 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA273EA/25 MSOP DGK OPA273EA/2K5 MSOP DGK OPA273UA/2K5 SOIC D OPA274EA/25 MSOP DGK OPA274UA/2K5 SOIC D OPA473EA/25 TSSOP PW OPA473EA/2K5 TSSOP PW OPA473UA/2K5 SOIC D OPA474EA/25 TSSOP PW OPA474EA/2K5 TSSOP PW OPA73NA/25 SOT-23 DBV OPA73NA/3K SOT-23 DBV OPA73UA/2K5 SOIC D OPA74NA/25 SOT-23 DBV OPA74NA/3K SOT-23 DBV OPA74UA/2K5 SOIC D Pack Materials-Page 2

18 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 6949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio Data Converters dataconverter.ti.com Automotive DSP dsp.ti.com Broadband Clocks and Timers Digital Control Interface interface.ti.com Medical Logic logic.ti.com Military Power Mgmt power.ti.com Optical Networking Microcontrollers microcontroller.ti.com Security RFID Telephony RF/IF and ZigBee Solutions Video & Imaging Wireless Mailing Address: Texas Instruments, Post Office Box 65533, Dallas, Texas Copyright 28, Texas Instruments Incorporated