INA126. MicroPOWER INSTRUMENTATION AMPLIFIER Single and Dual Versions IN ) G V IN G = 5 +

Transcription

1 INA6 INA6 INA6 INA6 INA6 INA6 INA6 SBOS06A JANUARY 996 REVISED AUGUST 005 MicroPOWER INSTRUMENTATION AMPLIFIER Single and Dual Versions FEATURES LOW QUIESCENT CURRENT: 75µA/chan. WIDE SUPPLY RANGE: ±.35V to ±V LOW OFFSET VOLTAGE: 50µV max LOW OFFSET DRIFT: 3µV/ C max LOW NOISE: 35nV/ Hz LOW INPUT BIAS CURRENT: 5nA max -PIN DIP, SO-, MSOP- SURFACE- MOUNT DUAL: 6-Pin DIP, SO-6, SSOP-6 APPLICATIONS INDUSTRIAL SENSOR AMPLIFIER: Bridge, RTD, Thermocouple PHYSIOLOGICAL AMPLIFIER: ECG, EEG, EMG MULTI-CHANNEL DATA ACQUISITION PORTABLE, BATTERY OPERATED SYSTEMS 3 V 7 0kΩ 0kΩ INA6 6 5 V O = (V IN V IN ) G 0kΩ G = 5 DESCRIPTION The INA6 and INA6 are precision instrumentation amplifiers for accurate, low noise differential signal acquisition. Their two-op-amp design provides excellent performance with very low quiescent current (75µA/channel). This, combined with a wide operating voltage range of ±.35V to ±V, makes them ideal for portable instrumentation and data acquisition systems. Gain can be set from 5V/V to 0000V/V with a single external resistor. Laser trimmed input circuitry provides low offset voltage (50µV max), low offset voltage drift (3µV/ C max) and excellent common-mode rejection. Single version package options include -pin plastic DIP, SO- surface mount, and fine-pitch MSOP- surface-mount. Dual version is available in the space-saving SSOP-6 finepitch surface mount, SO-6, and 6-pin DIP. All are specified for the 0 C to 5 C industrial temperature range. V INA6 0kΩ 0kΩ 0kΩ V O = ( V IN ) G G = 5 V O = (V IN V IN ) G G = 5 0kΩ 0kΩ V 6 0kΩ V Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright , Texas Instruments Incorporated

2 ABSOLUTE MAXIMUM RATINGS () Power Supply Voltage, V to V... 36V Input Signal Voltage ()... (V)0.7 to (V)0.7V Input Signal Current ()... 0mA Output Short Circuit... Continuous Operating Temperature C to 5 C Storage Temperature C to 5 C Lead Temperature (soldering, 0s) C NOTES: () Stresses above these ratings may cause permanent damage. () Input signal voltage is limited by internal diodes connected to power supplies. See text. PIN CONFIGURATION (Single) ELECTROSTATIC DISCHARGE SENSITIVITY This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. Top View -Pin DIP, SO-, MSOP- PACKAGE/ORDERING INFORMATION PACKAGE PRODUCT PACKAGE-LEAD MARKING V IN 7 V Single V IN V V O Ref INA6PA DIP- INA6PA INA6P DIP- INA6P INA6UA SO- INA6UA INA6U SO- INA6U INA6EA () MSOP- A6 (3) PIN CONFIGURATION (Dual) Top View 6-Pin DIP, SO-6, SSOP-6 " " " INA6E () MSOP- A6 (3) " " " Dual A 6 B INA6PA DIP-6 INA6PA INA6P DIP-6 INA6P A 5 B INA6UA SO-6 INA6UA INA6U SO-6 INA6U A A Ref A B B Ref B INA6EA () SSOP-6 INA6EA " " " INA6E () SSOP-6 INA6E " " " V OA Sense A V V OB Sense B V NOTES: () For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at. () MSOP- and SSOP-6 packages are available only on 50 or 500 piece reels. (3) Grade designation is marked on reel. INA6, INA6 SBOS06A

3 ELECTRICAL CHARACTERISTICS At T A = 5 C, V S = ±5V, R L = 5kΩ, unless otherwise noted. INA6P, U, E INA6P, U, E INA6PA, UA, EA INA6PA, UA, EA PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS INPUT Offset Voltage, RTI ±00 ±50 ±50 ±500 µv vs Temperature ±0.5 ±3 ±5 µv/ C vs Power Supply (PSRR) V S = ±.35V to ±V µv/v Input Impedance 0 9 Ω pf Safe Input Voltage R S = 0 (V)0.5 (V)0.5 V R S = kω (V)0 (V)0 V Common-Mode Voltage Range V O = 0V ±.5 ±.5 V Channel Separation (dual) G = 5, dc 30 db Common-Mode Rejection R S = 0, V CM = ±.5V db INA6U (dual SO-6) 0 9 db INPUT BIAS CURRENT na vs Temperature ±30 pa/ C Offset Current ±0.5 ± ±5 na vs Temperature ±0 pa/ C GAIN G = 5 to 0k V/V Gain Equation G = 5 0kΩ/ V/V Gain Error V O = ±V, G = 5 ±0.0 ±0. ±0. % vs Temperature G = 5 ± ±0 ppm/ C Gain Error V O = ±V, G = 00 ±0. ±0.5 ± % vs Temperature G = 00 ±5 ±00 ppm/ C Nonlinearity G = 00, V O = ±V ±0.00 ±0.0 % NOISE Voltage Noise, f = khz 35 nv/ Hz f = 00Hz 35 nv/ Hz f = 0Hz 5 nv/ Hz f B = 0.Hz to 0Hz 0.7 µv PP Current Noise, f = khz 60 fa/ Hz f B = 0.Hz to 0Hz pa PP OUTPUT Voltage, Positive R L = 5kΩ (V)0.9 (V)0.75 V Negative R L = 5kΩ (V)0.95 (V)0. V Short-Circuit Current Short-Circuit to Ground 0/5 ma Capacitive Load Drive 000 pf FREQUENCY RESPONSE Bandwidth, 3dB G = 5 00 khz G = 00 9 khz G = 500. khz Slew Rate V O = ±0V, G = 5 0. V/µs Settling Time, 0.0% 0V Step, G = 5 30 µs 0V Step, G = µs 0V Step, G = µs Overload Recovery 50% Input Overload µs POWER SUPPLY Voltage Range ±.35 ±5 ± V Current (per channel) I O = 0 ±75 ±00 µa TEMPERATURE RANGE Specification Range 0 5 C Operation Range 55 5 C Storage Range 55 5 C Thermal Resistance, θ JA -Pin DIP 00 C/W SO- Surface-Mount 50 C/W MSOP- Surface-Mount 00 C/W 6-Pin DIP (dual) 0 C/W SO-6 (dual) 00 C/W SSOP-6 (dual) 00 C/W Specification same as INA6P, INA6U, INA6E; INA6P, INA6U, INA6E. INA6, INA6 3 SBOS06A

4 TYPICAL CHARACTERISTICS At T A = 5 C and V S = ±5V, unless otherwise noted. Gain (db) GAIN vs FREQUENCY G = G = G = 0 G = k 0k 00k M Common-Mode Rejection (db) COMMON-MODE REJECTION vs FREQUENCY G = G = G = k 0k 00k M Frequency (Hz) Frequency (Hz) 0 POSITIVE POWER SUPPLY REJECTION vs FREQUENCY G = NEGATIVE POWER SUPPLY REJECTION vs FREQUENCY Power Supply Rejection (db) G = 5 G = 00 Power Supply Rejection (db) G = 000 G = 5 G = k 0k 00k M Frequency (Hz) k 0k 00k M Frequency (Hz) Common-Mode Voltage (V) INPUT COMMON-MODE RANGE vs OUTPUT VOLTAGE, V S = ±5V Limited by A output swing see text 5V V D/ V D/ Ref V CM 5V V O Limited by A output swing see text Input Common-Mode Voltage (V) INPUT COMMON-MODE VOLTAGE RANGE vs OUTPUT VOLTAGE, V S = ±5V Limited by A output swing see text V S = ±5V V S = 5V/0V V REF =.5V Limited by A output swing see text Output Voltage (V) Output Voltage (V) INA6, INA6 SBOS06A

5 TYPICAL CHARACTERISTICS (Cont.) At T A = 5 C and V S = ±5V, unless otherwise noted. 00 INPUT-REFERRED NOISE vs FREQUENCY k 000 SETTLING TIME vs GAIN Input Voltage Noise (nv/ Hz) 0 Voltage Noise Current Noise 00 Input Current Noise (fa/ Hz) Settling Time (µs) % 0.% 0 00 k 0k Frequency (Hz) k Gain (V/V) Offset Voltage Change (µv) INPUT-REFERRED OFFSET VOLTAGE WARM-UP Time After Turn-On (ms) (Noise) Quiescent Current (µa) QUIESCENT CURRENT AND SLEW RATE vs TEMPERATURE I Q Temperature ( C) SR SR V S = ±.35V V S = ±5V Slew Rate (V/µs) TOTAL HARMONIC DISTORTIONNOISE vs FREQUENCY V OUTPUT VOLTAGE SWING vs OUTPUT CURRENT (V) Sourcing Current THDN (%) R L = Output Voltage (V) (V) (V) G = 5 R L = 00kΩ (V) Sinking Current k Frequency (Hz) 0k V Output Current (ma) INA6, INA6 5 SBOS06A

6 TYPICAL CHARACTERISTICS (Cont.) At T A = 5 C and V S = ±5V, unless otherwise noted. SMALL-SIGNAL RESPONSE, G = 5 SMALL-SIGNAL RESPONSE, G = 00 0mV/div 0mV/div 50µs/div 50µs/div LARGE-SIGNAL RESPONSE, G = 5 VOLTAGE NOISE, 0.Hz to 0Hz 5V/div 0.µV/div 50µs/div 500ms/div CHANNEL SEPARATION vs FREQUENCY, RTI (Dual Version) G = 000 Separation (db) R L = 5kΩ Measurement limited by amplifier or measurement noise. G = 00 G = k 0k 00k M Frequency (Hz) 6 INA6, INA6 SBOS06A

7 APPLICATION INFORMATION Figure shows the basic connections required for operation of the INA6. Applications with noisy or high impedance power supplies may require decoupling capacitors close to the device pins as shown. The output is referred to the output reference (Ref) terminal which is normally grounded. This must be a low-impedance connection to ensure good common-mode rejection. A resistance of Ω in series with the Ref pin will cause a typical device to degrade to approximately 0dB CMR. Dual versions (INA6) have feedback sense connections, Sense A and Sense B. These must be connected to their respective output terminals for proper operation. The sense connection can be used to sense the output voltage directly at the load for best accuracy. SETTING THE GAIN Gain is set by connecting an external resistor,, as shown: G =5 0kΩ Commonly used gains and resistor values are shown in Figure. The 0kΩ term in equation comes from the internal metal film resistors which are laser trimmed to accurate absolute values. The accuracy and temperature coefficient of these resistors are included in the gain accuracy and drift specifications. The stability and temperature drift of the external gain setting resistor,, also affects gain. s contribution to gain accuracy and drift can be directly inferred from the gain () equation (). Low resistor values required for high gain can make wiring resistance important. Sockets add to the wiring resistance, which will contribute additional gain error in gains of approximately 00 or greater. OFFSET TRIMMING The INA6 and INA6 are laser trimmed for low offset voltage and offset voltage drift. Most applications require no external offset adjustment. Figure shows an optional circuit for trimming the output offset voltage. The voltage applied to the Ref terminal is added to the output signal. An op amp buffer is used to provide low impedance at the Ref terminal to preserve good common-mode rejection. INA6 Ref OPA37 ±0mV Adjustment Range Dual version has external sense connection. 00µA / REF00 00Ω 00Ω 00µA / REF00 FIGURE. Optional Trimming of Output Offset Voltage. V O V V V DESIRED GAIN NEAREST % (V/V) (Ω) VALUE 5 NC NC 0 6k 5.k Pin numbers are for single version 3 INA6 A 7 0.µF 0kΩ 6 Load G = 5 0kΩ V O = (V IN V IN ) G V O NC: No Connection. Also drawn in simplified form: A V IN 0kΩ 0.µF 5 Ref INA6 Ref V O Dual version has external sense connection. V FIGURE. Basic Connections. INA6, INA6 7 SBOS06A

8 INPUT BIAS CURRENT RETURN The input impedance of the INA6/6 is extremely high approximately 0 9 Ω. However, a path must be provided for the input bias current of both inputs. This input bias current is typically 0nA (current flows out of the input terminals). High input impedance means that this input bias current changes very little with varying input voltage. Input circuitry must provide a path for this input bias current for proper operation. Figure 3 shows various provisions for an input bias current path. Without a bias current path, the inputs will float to a potential which exceeds the commonmode range and the input amplifiers will saturate. If the differential source resistance is low, the bias current return path can be connected to one input (see the thermocouple example in Figure 3). With higher source impedance, using two equal resistors provides a balanced input with advantages of lower input offset voltage due to bias current and better high-frequency common-mode rejection. Microphone, Hydrophone etc. Thermocouple 7kΩ FIGURE 3. Providing an Input Common-Mode Current Path. INPUT COMMON-MODE RANGE The input common-mode range of the INA6/6 is shown in the typical characteristic curves. The commonmode range is limited on the negative side by the output voltage swing of A, an internal circuit node that cannot be measured on an external pin. The output voltage of A can be expressed as: 7kΩ INA6 V O =.5 ( ) (/ ) () (Voltages referred to Ref terminal, pin 5) INA6 INA6 Center-tap provides bias current return. The internal op amp A is identical to A and its output swing is limited to typically 0.7V from the supply rails. When the input common-mode range is exceeded (A s output is saturated), A can still be in linear operation and respond to changes in the non-inverting input voltage. The output voltage, however, will be invalid. LOW VOLTAGE OPERATION The INA6/6 can be operated on power supplies as low as ±.35V. Performance remains excellent with power supplies ranging from ±.35V to ±V. Most parameters vary only slightly throughout this supply voltage range see typical characteristic curves. Operation at very low supply voltage requires careful attention to ensure that the commonmode voltage remains within its linear range. See Input Common-Mode Voltage Range. The INA6/6 can be operated from a single power supply with careful attention to input common-mode range, output voltage swing of both op amps and the voltage applied to the Ref terminal. Figure shows a bridge amplifier circuit operated from a single 5V power supply. The bridge provides an input common-mode voltage near.5v, with a relatively small differential voltage. INPUT PROTECTION The inputs are protected with internal diodes connected to the power supply rails. These diodes will clamp the applied signal to prevent it from exceeding the power supplies by more than approximately 0.7V. If the signal source voltage can exceed the power supplies, the source current should be limited to less than 0mA. This can generally be done with a series resistor. Some signal sources are inherently currentlimited and do not require limiting resistors. CHANNEL CROSSTALK DUAL VERSION The two channels of the INA6 are completely independent, including all bias circuitry. At DC and low frequency there is virtually no signal coupling between channels. Crosstalk increases with frequency and is dependent on circuit gain, source impedance and signal characteristics. As source impedance increases, careful circuit layout will help achieve lowest channel crosstalk. Most crosstalk is produced by capacitive coupling of signals from one channel to the input section of the other channel. To minimize coupling, separate the input traces as far as practical from any signals associated with the opposite channel. A grounded guard trace surrounding the inputs helps reduce stray coupling between channels. Carefully balance the stray capacitance of each input to ground, and run the differential inputs of each channel parallel to each other, or directly adjacent on top and bottom side of a circuit board. Stray coupling then tends to produce a common-mode signal that is rejected by the IA s input. INA6, INA6 SBOS06A

9 5V The ADS77 s V REF input current is proportional to conversion rate. A conversion rate of 0kS/s or slower assures enough current to turn on the reference diode. Converter input range is ±.V. Output swing limitation of INA6 limits the A/D converter to somewhat greater than bits of range. Bridge Sensor.5V V.5V V 3 7 INA6 A 0kΩ A 0kΩ 6 5.V R kω C 0.7µF R kω R, C, R : 30Hz LP 33µA 3 IN IN V REF ADS77 -Bit A/D INA6 and ADS77 are available in fine-pitch MSOP- package D C S Ck 6 Serial Data 5 7 Chip Select Clock 6 REF00C-. A similar instrumentation amplifier, INA5, provides an internal reference voltage for sensor excitation and/or A/D converter reference. Dual version has external sense connection. Pin numbers shown are for single version. FIGURE. Bridge Signal Acquisition Single 5V Supply. R INA6 Ref I B V I O = IN G R A I O A I B Error Load OPA77 OPA30 OPA60 OPA9 ±.5nA ±0pA ±pa ±00fA Dual version has external sense connection. FIGURE 5. Differential Voltage-to-Current Converter. INA6, INA6 9 SBOS06A

10 PACKAGE OPTION ADDENDUM -Jan-007 PACKAGING INFORMATION Orderable Device Status () Package Type Package Drawing Pins Package Qty INA6E/50 ACTIVE MSOP DGK 50 Green (RoHS & INA6E/50G ACTIVE MSOP DGK 50 Green (RoHS & INA6E/K5 ACTIVE MSOP DGK 500 Green (RoHS & INA6E/K5G ACTIVE MSOP DGK 500 Green (RoHS & INA6EA/50 ACTIVE MSOP DGK 50 Green (RoHS & INA6EA/50G ACTIVE MSOP DGK 50 Green (RoHS & INA6EA/K5 ACTIVE MSOP DGK 500 Green (RoHS & INA6EA/K5G ACTIVE MSOP DGK 500 Green (RoHS & INA6P ACTIVE PDIP P 50 Green (RoHS & INA6PA ACTIVE PDIP P 50 Green (RoHS & INA6PAG ACTIVE PDIP P 50 Green (RoHS & INA6PG ACTIVE PDIP P 50 Green (RoHS & INA6U ACTIVE SOIC D 00 Green (RoHS & INA6U/K5 ACTIVE SOIC D 500 Green (RoHS & INA6U/K5G ACTIVE SOIC D 500 Green (RoHS & INA6UA ACTIVE SOIC D 00 Green (RoHS & INA6UA/K5 ACTIVE SOIC D 500 Pb-Free (RoHS) INA6UA/K5E ACTIVE SOIC D 500 Pb-Free (RoHS) INA6UAG ACTIVE SOIC D 00 Green (RoHS & INA6UG ACTIVE SOIC D 00 Green (RoHS & INA6E/50 ACTIVE SSOP/ QSOP INA6E/50G ACTIVE SSOP/ QSOP INA6E/K5 ACTIVE SSOP/ QSOP INA6E/K5G ACTIVE SSOP/ QSOP INA6EA/50 ACTIVE SSOP/ QSOP DBQ 6 50 Green (RoHS & DBQ 6 50 Green (RoHS & DBQ Green (RoHS & DBQ Green (RoHS & DBQ 6 50 Green (RoHS & Eco Plan () Lead/Ball Finish MSL Peak Temp (3) Level--60C- YEAR Level--60C- YEAR Level--60C- YEAR Level--60C- YEAR Level--60C- YEAR Level--60C- YEAR Level--60C- YEAR Level--60C- YEAR N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type Addendum-Page

11 PACKAGE OPTION ADDENDUM -Jan-007 Orderable Device Status () Package Type INA6EA/50G ACTIVE SSOP/ QSOP INA6EA/K5 ACTIVE SSOP/ QSOP INA6EA/K5G ACTIVE SSOP/ QSOP Package Drawing Pins Package Qty DBQ 6 50 Green (RoHS & DBQ Green (RoHS & DBQ Green (RoHS & INA6P ACTIVE PDIP N 6 5 Green (RoHS & INA6PA ACTIVE PDIP N 6 5 Green (RoHS & INA6PAG ACTIVE PDIP N 6 5 Green (RoHS & INA6PG ACTIVE PDIP N 6 5 Green (RoHS & INA6U ACTIVE SOIC D 6 Pb-Free (RoHS) INA6UA ACTIVE SOIC D 6 Green (RoHS & INA6UA/K5 ACTIVE SOIC D Pb-Free (RoHS) INA6UA/K5E ACTIVE SOIC D Pb-Free (RoHS) INA6UAE ACTIVE SOIC D 6 Pb-Free (RoHS) INA6UAG ACTIVE SOIC D 6 Green (RoHS & INA6UE ACTIVE SOIC D 6 Pb-Free (RoHS) SN DRE ACTIVE SOIC D Pb-Free (RoHS) Eco Plan () Lead/Ball Finish MSL Peak Temp (3) Call TI Call TI Call TI Call TI N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type N / A for Pkg Type () The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. () Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & - please check for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either ) lead-based flip-chip solder bumps used between the die and package, or ) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & : TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is Addendum-Page

12 PACKAGE OPTION ADDENDUM -Jan-007 provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3

13 MECHANICAL DATA MPDI00A JANUARY 995 REVISED JUNE 999 P (R-PDIP-T) PLASTIC DUAL-IN-LINE 0.00 (0,60) (9,0) (6,60) 0.0 (6,0) (,7) MAX 0.00 (0,5) MIN 0.35 (,6) (7,6) 0.05 (0,3) 0.00 (5,0) MAX Gage Plane Seating Plane 0.5 (3,) MIN 0.00 (0,5) NOM 0.0 (0,53) 0.05 (0,3) 0.00 (,5) 0.00 (0,5) M 0.30 (0,9) MAX 000/D 05/9 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-00 For the latest package information, go to POST OFFICE BOX DALLAS, TEXAS 7565

14

15

16

17

18

19 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio /audio Data Converters dataconverter.ti.com Automotive /automotive DSP dsp.ti.com Broadband /broadband Interface interface.ti.com Digital Control /digitalcontrol Logic logic.ti.com Military /military Power Mgmt power.ti.com Optical Networking /opticalnetwork Microcontrollers microcontroller.ti.com Security /security Low Power Wireless /lpw Telephony /telephony Video & Imaging /video Wireless /wireless Mailing Address: Texas Instruments Post Office Box Dallas, Texas 7565 Copyright 007, Texas Instruments Incorporated