Tutorial 4 - Open Dxf file and create multiple toolpaths (Contour, Pocket and Drill).
|
|
|
- Veronica Houston
- 5 years ago
- Views:
Transcription
1 Tutorial 4 - Open Dxf file and create multiple toolpaths (Contour, Pocket and Drill). In this tutorial you will open a Dxf file and create the toolpath that cut the external of the part, another toolpath to remove the material contained in a closed profile, and a tool-change with the drill operation. Caution: CNC machines are potentially dangerous. The post-processor can output code unsuitable for your machine's control. Check the Nc file before sending it to a CNC machine.
2 1. Open the Dxf file with the "Open" button. 2. Select in "..\SimplyCam\Sample\" folder the SAMPLE_POCKET.DXF file. 3. The Info panel will appear with the info and dimension of image. Press "Next Page" button.
3 4. Define the reference point of the drawing and press "Done" button. 5. Turn in the "Off" state the button "Show grid" and "Show Axis".
4 6. The drawing is displayed in graphic area without the grid, the axis direction, the origin and the scale info.
5 7. Press "Nc Program" button to go in toolpath section. This section contain 5 pages: Page 1: File/Postprocessor definition Page 2: Tool/Operation definition Page 3: Profile/Cutter compensation selection Page 4: Cutting parameter setting Page 5: Nc file simulating or editing 8. Select the postprocessor of your Cnc machine.
6 9. Press "New" button to create new toolpath. 10. Type "test" in the Windows file dialog. 11. Press "Next Pg(2)" button.
7 12. In Tool section press "Select" button to retrieve a tool from a tool library or create a new tool.
8 13. Click in the Tool List to select the Flat tool with diameter 8. Set feeds and speed of the tool. Press the "OK" button. 14. In the Operation section, select "Contour" and press "Next Pg(3)".
9 15. The "Profile definition" page appears. Press the "Chain" button. 16. Pick the geometry near to start point as indicate by red square.
10 17. The yellow arrow appears to indicate the start point of contour and the direction of contour. The blue boundary is the chained profile. 18. In the "Profile definition" press the "Reverse" button and press "Next Pg(3)".
11 19. The new direction of the chain is showing. 20. In the "Cutter compensation" section, set the "Offset Side" on OutSide.
12 21. Another yellow arrow, smaller then previous, appears to indicate the direction of cutter compensation. The long arrow = Toolpath direction The small arrow = Cutter compensation direction. 22. Set the "Lead in" and "Lead out". 23. And then press "Next Pg(4)" button.
13 24. The "Contour parameter" page appear. Set up the following parameters: 25. Feed plane: set the height that the tool rapids to (G0) before changing to the feed rate (G1) to enter in the part (absolute).
14 26. Top of part: set the height of the piece in the Z axis (absolute). 27. Depth: set the final machining depth (absolute).
15 28. Depth increment: set the maximum amount of material to remove for each Z cut. 29. Write EOF: Turn "Off" this parameter for not write in the Nc file the "End Of File" section (typically M2 or M30).
16 30. Press the "Calculate" button to machining the chained geometry with the cutting parameters. 31. The "Nc File" page is displayed and in the graphic area the toolpath is simulated.
17 32. Press the "Rewind" button. 33. Move the slider near to slow position. 34. Press the "Play" button to simulate the toolpath (Yellow=Rapid, Cyan=Feed) in the graphic area.
18 35. The first toolpath (Contour) is simulated. The "Z Depth" panel indicator reflect the actual Z tool position (Yellow=Rapid, Cyan=Feed). 36. Press the "Prev Pg(4)" button. 37. "Remove the last operation created?" No, the contour toolpath is correct, we want to preserve it.
19 38. Press the "Prev Pg(3)" button and Press the "Prev Pg(2)" button. 39. In the Operation section, select "Pocket" and press "Next Pg(3)". 40. The "Profile definition" page appear. Press the "Unselect" button to remove the last chain.
20 41. Press the "Chain" button. 42. Pick the geometry near to start point as indicate by red square.
21 43. Two yellow arrows appear. The long arrow indicate the start point of boundary and the direction of toolpath. The small arrow indicate the side of toolpath. The blue boundary is the chained profile. 44. Press the "Next Pg(4)" button. 45. The "Pocket parameters" page appears. Set up the following parameters:
22 46. Feed plane: set the height that the tool rapids to (G0) before changing to the feed rate (G1) to enter in the part (absolute). 47. Top of part: set the height of the piece in the Z axis (absolute).
23 48. Depth: set the final machining depth (absolute). 49. Depth increment: set the maximum amount of material to remove for each Z cut.
24 50. Write EOF: Turn "Off" this parameter for not write in the Nc file the "End Of File" section (typically M2 or M30). 51. Press the "Calculate" button to machining the chained geometry with the cutting parameters.
25 52. The "Nc File" page is displayed and in the graphic area the toolpath is simulated. 53. Press the "Rewind" button. 54. Press the "Play" button to simulate the toolpath (Yellow=Rapid, Cyan=Feed) in the graphic area.
26 55. In the graphic area the first Contour toolpath and the second Pocket toolpath are simulated. 56. Press the "Prev Pg(4)" button. 57. "Remove the last operation created?" No, the pocket toolpath is correct, we want to preserve it.
27 58. Press the "Prev Pg(3)" button and Press the "Prev Pg(2)" button. 59. In Tool section press "Select" button to retrieve a tool from a tool library or create a new tool.
28 60. Click in the Tool List to select the Drill tool with diameter 3. Set feeds and speed of the tool. Press the "OK" button.
29 61. Change the number of tool in 2. This new number, different from previous, force SimplyCam to generate in next operatation the tool change. Press the "OK" button.
30 62. In the Operation section, select "Drill" and press "Next Pg(3)". 63. The "Drill points select" page appear. Press the "All arcs" button to select all the closed arcs in geometry.
31 64. The yellow arrow appears to indicate the start point and the direction of drilling. 65. Press the "Next Pg(4)" button. 66. The "Drill parameters" page appears. Set up the following parameters: Note: the sequence of the drilling cycle is listed below: Drill cycle: - Rapid to the hole center with XY axis - Rapid Z to feed plane (Reference height) - Feed Z to the Z depth - Rapidly retract Z to feed plane (reference height) - Rapid to another hole center and repeat the sequence Peck Drill cycle: - Rapid to the hole center with XY axis - Rapid Z to feed plane (Reference height) - Feed Z down with one depth increment - Rapidly retract Z to feed plane - Rapid Z down to clearance up from the previous drilled depth - Feed Z down with one depth increment - Repeat the last 2 step until the hole bottom is reached - Rapidly retract Z to feed plane (reference height) - Rapid to another hole center and repeat the sequence 67. Feed plane: set the height that the tool rapids to (G0) before changing to the feed rate (G1) to enter in the part (absolute). 68. Top of part: set the height of the piece in the Z axis (absolute).
32 69. Depth: set the final depth of drilling operation (absolute). 70. Cycle: select the drilling cycle.
33 71. Depth increment: set the amount of material to remove for each Z cut. 72. Write EOF: Turn "On" this parameter for write in the Nc file the "End Of File" section (typically M2 or M30). This is the last operation of the example.
34 73. Press the "Calculate" button to drilling the definite points with the cutting parameters. 74. The "Nc File" page is displayed and in the graphic area the drillng toolpath is simulated.
35 75. The Tool-change section is added in Nc file 76. And the EOF (end of file) sequence is added at end of the Nc file. 77. Press the "Rewind" button.
36 78. Press the "Play" button to simulate the contour, pocket and drill toolpaths in the graphic area. 79. You have successfully created the multi-toolpath example with SimplyCam. Caution: CNC machines are potentially dangerous. The post-processor can output code unsuitable for your machine's control. Check the Nc file before sending it to a CNC machine.
In this tutorial you will open a Dxf file and create the toolpath that cut the external of the part.
Tutorial 2 - Open Dxf file and create the outside Contour toolpath. In this tutorial you will open a Dxf file and create the toolpath that cut the external of the part. Caution: CNC machines are potentially
In this tutorial you will open a Dxf file and create the toolpath to remove the material contained in a closed profile.
Tutorial 3 - Open Dxf file and create the Pocket toolpath. In this tutorial you will open a Dxf file and create the toolpath to remove the material contained in a closed profile. Caution: CNC machines
ENGI 7962 Mastercam Lab Mill 1
ENGI 7962 Mastercam Lab Mill 1 Starting a Mastercam file: Once the SolidWorks models is complete (all sketches are Fully Defined), start up Mastercam and select File, Open, Files of Type, SolidWorks Files,
Kerf Bent Clock Front Toolpaths in MasterCAM. Open the MasterCAM application and open your clock front geometry file.
Kerf Bent Clock Front Toolpaths in MasterCAM Open the MasterCAM application and open your clock front geometry file. For 2D geometry such as we have, there are 2 main types of tool paths. The first one
MadCAM 2.0: Drill Pattern Toolpath
MadCAM 2.0: Drill Pattern Toolpath Digital Media Tutorial 2005-2006 MadCAM 2.0 can create a toolpath to drill holes directly into your material. The bit plunges in and out of the material without moving
Figure 1: NC Lathe menu
Click To See: How to Use Online Documents SURFCAM Online Documents 685)&$0Ã5HIHUHQFHÃ0DQXDO 5 /$7+( 5.1 INTRODUCTION The lathe mode is used to perform operations on 2D geometry, turned on two axis lathes.
Flip for User Guide. Inches. When Reliability Matters
Flip for User Guide Inches by When Reliability Matters Mastercam HSM Performance Pack Tutorial 1 Mastercam HSM Performance Pack Tutorial Tutorial I... 2 Getting started... 2 Tools used... 2 Roughing...
MasterCAM for Dresser Valet
MasterCAM for Dresser Valet Check to make sure the nethasp is working/turned on to network. Go to ALL APPs/Mastercam x8/nethasp After the computer reads the nethasp, these programs should show up. If not
Projects. 5 For each component, produce a drawing showing the intersection BO.O. C'BORE 18 DIA x 5 DEEP FROM SECTION ON A - A
Projects ~ Figure Pl Project 1 If you have worked systematically through the assignments in this workbook, you should now be able to tackle the following milling and turning projects. It is suggested that
Figure 1: NC EDM menu
Click To See: How to Use Online Documents SURFCAM Online Documents 685)&$0Ã5HIHUHQFHÃ0DQXDO 6 :,5(('0 6.1 INTRODUCTION SURFCAM s Wire EDM mode is used to produce toolpaths for 2 Axis and 4 Axis EDM machines.
for Solidworks TRAINING GUIDE LESSON-9-CAD
for Solidworks TRAINING GUIDE LESSON-9-CAD Mastercam for SolidWorks Training Guide Objectives You will create the geometry for SolidWorks-Lesson-9 using SolidWorks 3D CAD software. You will be working
10 x 16 Cutting Board - Juice Groove in MasterCAM
10 x 16 Cutting Board - Juice Groove in MasterCAM Check to make sure the nethasp is working/turned on to network. Go to ALL APPs/Mastercam x8/nethasp After the computer reads the nethasp, these programs
VisualCAM 2018 TURN Quick Start MecSoft Corporation
2 Table of Contents About this Guide 4 1 About... the TURN Module 4 2 Using this... Guide 4 3 Useful... Tips 5 Getting Ready 7 1 Running... VisualCAM 2018 7 2 About... the VisualCAD Display 7 3 Launch...
Flip for User Guide. Metric. When Reliability Matters
Flip for User Guide Metric by When Reliability Matters Mastercam HSM Performance Pack Tutorial 1 Mastercam HSM Performance Pack Tutorial Tutorial I... 2 Getting started... 2 Tools used... 2 Roughing...
EASY CNC. Table of Contents
Square 1 Electronics announces its new book by David Benson, "Easy CNC", A Beginner's Guide to CNC" The complete table of contents follows: This book was written by David Benson (8-1/2 x 11", 200 pages,
Fusion 360 Part Setup. Tutorial
Fusion 360 Part Setup Tutorial Table of Contents MODEL SETUP CAM SETUP TOOL PATHS MODEL SETUP The purpose of this tutorial is to demonstrate start to finish, importing a machineable part to generating
Using Siemens NX 11 Software. The connecting rod
Using Siemens NX 11 Software The connecting rod Based on a Catia tutorial written by Loïc Stefanski. At the end of this manual, you should obtain the following part: 1 Introduction. Start NX 11 and open
Tutorial 1 getting started with the CNCSimulator Pro
CNCSimulator Blog Tutorial 1 getting started with the CNCSimulator Pro Made for Version 1.0.6.5 or later. The purpose of this tutorial is to learn the basic concepts of how to use the CNCSimulator Pro
CNC Machinery. Module 5: CNC Programming / Milling. IAT Curriculum Unit PREPARED BY. August 2009
CNC Machinery Module 5: CNC Programming / Milling PREPARED BY IAT Curriculum Unit August 2009 Institute of Applied Technology, 2009 ATM313-CNC Module 5: CNC Programming / Milling Module Objectives: 1.
Digital Media Tutorial Written By John Eberhart
MadCAM MadCAM 5.0: Large 4.1: Large & Medium CNC Tool CNC Path Tool Path Generator Generator Digital Media Tutorial Written By John Eberhart MadCAM is a tool path generator that works inside Rhino. It
MACH3 TURN ARC MOTION 6/27/2009 REV:0
MACH3 TURN - ARC MOTION PREFACE This is a tutorial about using the G2 and G3 g-codes relative to Mach3 Turn. There is no simple answer to a lot of the arc questions posted on the site relative to the lathe.
LinuxCNC Help for the Sherline Machine CNC System
WEAR YOUR SAFETY GLASSES FORESIGHT IS BETTER THAN NO SIGHT READ INSTRUCTIONS BEFORE OPERATING LinuxCNC Help for the Sherline Machine CNC System LinuxCNC Help for Programming and Running 1. Here is a link
Using Surfcam to Produce a Numeric Control (NC) Program Part #1 Surfcam Demonstration Version Use
Using Surfcam to Produce a Numeric Control (NC) Program Part #1 Surfcam Demonstration Version Use An Introduction to the CAD/CAM Process Instructions for 3 Axis Programming Using the D&M CNC Milling Machine
Siemens NX11 tutorials. The angled part
Siemens NX11 tutorials The angled part Adaptation to NX 11 from notes from a seminar Drive-to-trial organized by IBM and GDTech. This tutorial will help you design the mechanical presented in the figure
Controlled Machine Tools
ME 440: Numerically Controlled Machine Tools CNCSIMULATOR Choose the correct application (Milling, Turning or Plasma Cutting) CNCSIMULATOR http://www.cncsimulator.com Teaching Asst. Ergin KILIÇ (M.S.)
MasterCAM for Sculpted Bench
MasterCAM for Sculpted Bench Check to make sure the nethasp is working/turned on to network. Go to ALL APPs/Mastercam x8/nethasp After the computer reads the nethasp, these programs should show up. If
CNC PROGRAMMING WORKBOOK. Sample not for. Distribution MILL & LATHE. By Matthew Manton and Duane Weidinger
CNC PROGRAMMING WORKBOOK MILL & LATHE By Matthew Manton and Duane Weidinger CNC Programming Workbook Mill & Lathe Published by: CamInstructor Incorporated 330 Chandos Crt. Kitchener, Ontario N2A 3C2 www.caminstructor.com
Toothbrush Holder Project 2D Machining
Toothbrush Holder Project 2D Machining Prerequisite Toothbrush Holder drawn and saved as a DXF file in SolidWorks Focus of the Lesson On completion of this exercise you will have: Used the Techsoft 2D
Prasanth. Lathe Machining
Lathe Machining Overview Conventions What's New? Getting Started Open the Part to Machine Create a Rough Turning Operation Replay the Toolpath Create a Groove Turning Operation Create Profile Finish Turning
Conversational Programming. Alexsys Operator Manual
Conversational Programming Alexsys Operator Manual Alexsys Operator Manual 1. Overview ALEXSYS is a programming system for CNC machining centers. That combines features of CAD / CAM systems with typical
Prismatic Machining Preparation Assistant
Prismatic Machining Preparation Assistant Overview Conventions What's New Getting Started Open the Design Part and Start the Workbench Automatically Create All Machinable Features Open the Manufacturing
Pro/NC. Prerequisites. Stats
Pro/NC Pro/NC tutorials have been developed with great emphasis on the practical application of the software to solve real world problems. The self-study course starts from the very basic concepts and
STATE UNIVERSITY OF NEW YORK COLLEGE OF TECHNOLOGY CANTON, NEW YORK COURSE OUTLINE MECH 223 INTRODUCTION TO COMPUTER NUMERICAL CONTROL
STATE UNIVERSITY OF NEW YORK COLLEGE OF TECHNOLOGY CANTON, NEW YORK COURSE OUTLINE MECH 223 INTRODUCTION TO COMPUTER NUMERICAL CONTROL Prepared by: Daniel Miller Updated by: Daniel Miller (April 2015)
CNC Turning Training CNC MILLING / ROUTING TRAINING GUIDE. Page 1
CNC Turning Training www.denford.co.uk Page 1 Table of contents Introduction... 3 Start the VR Turning Software... 3 Configure the software for the machine... 4 Load your CNC file... 5 Configure the tooling...
CNC Router Part 2 Training Tutorial
CNC Router Part 2 Training Tutorial Prepared by Steve Pilon - Version 1.1 September 2017 A Index B - Intro A- Index B- Intro C- Objective D- Required Items E- Opening CamBam and Loading a DXF F- Preparing
Purdue AFL. CATIA CAM Process Reference Rev. B
Purdue AFL CATIA CAM Process Reference Rev. B Revision Notes Revision - of this document refers to the CATIA v5r21 deployment of the AFL CATIA Environment. All information contained in this reference document
CAMWorks How To Create CNC G-Code for CO2 Dragsters
Objective: In this chapter we will show how to mill out the axle holes for this CO2 Dragster from the left side. VI.1. Open the previously created file: Dragster axle hole 001.sldprt. VI.2. Select the
What s new in IGEMS R9
General changes and CAD-commands What s new in IGEMS R9 Page 1 General changes and CAD-commands What s new in IGEMS R9 This document is not a complete manual. It describes only the differences between
Cube in a cube Fusion 360 tutorial
Cube in a cube Fusion 360 tutorial n Before using these instructions, it is helpful to watch this video screencast of the CAD drawing actually being done in the software. Click to link to the video tutorial.
Design & Manufacturing II. The CAD/CAM Labs. Lab I Process Planning G-Code Mastercam Lathe
2.008 Design & Manufacturing II The CAD/CAM Labs Lab I Process Planning G-Code Mastercam Lathe Lab II Mastercam Mill Check G-Code Lab III CNC Mill & Lathe Machining OBJECTIVE BACKGROUND LAB EXERCISES DELIVERABLES
CAMWorks How To Create CNC G-Code for CO2 Dragsters
Creating the Left Side Smooth Finish Tool Path. This chapter will focus on the steps for creating the left side smooth finish tool path. The objective of this chapter is to create to an accurate and highly
FoamWorks Introduction. David Mrozinski 848 W. Borton Road Essexville, Michigan 48732
FoamWorks 4.0 Introduction Quick Start Registration Registration Menus Files Save a Cut Profile Load a Cut Profile Close Profile/G-code Restore Default Cut Profile Exit Setup Setup Parameters Generate
What's New in RhinoCAM 2018
What's New in RhinoCAM 2018 Dec 12 This document describes new features and enhancements introduced in MecSoft s RhinoCAM 2018 product. 2018, MecSoft Corporation 1 CONTENTS RhinoCAM 2018... 3 Common Enhancements...
HAAS AUTOMATION, INC. PROGRAMMING MILL SERIES WORKBOOK ANSWERS HAAS AUTOMATION, INC STURGIS ROAD OXNARD, CA
HAAS AUTOMATION, INC. MILL SERIES PROGRAMMING WORKBOOK HAAS AUTOMATION, INC. 2800 STURGIS ROAD OXNARD, CA 93030 www.haascnc.com 800-331-6746 ANSWERS PROGRAMMING HAAS AUTOMATION INC. 2800 Sturgis Road Oxnard,
CAD Tutorial 24: Step by Step Guide
CAD TUTORIAL 24: Step by step CAD Tutorial 24: Step by Step Guide Level of Difficulty Time Approximately 40 50 minutes Lesson Objectives To understand the basic tools used in SketchUp. To understand the
NZX NLX
NZX2500 4000 6000 NLX1500 2000 2500 Table of contents: 1. Introduction...1 2. Required add-ins...1 2.1. How to load an add-in ESPRIT...1 2.2. AutoSubStock (optional) (for NLX configuration only)...3 2.3.
Chair. Bottom Rail. on the Command Manager. on the Weldments toolbar.
Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click
Standard. CNC Turning & Milling Machine Rev 1.0. OM5 Control Software Instruction Manual
Standard CNC Turning & Milling Machine Rev 1.0 OM5 Control Software Instruction Manual Legacy Woodworking Machinery 435 W. 1000 N. Springville, UT 84663 Standard CNC Machine 2 Content Warranty and Repair
SolidCAM imachining. imachining Tool paths
SolidCAM imachining SolidCAM imachining is an intelligent High Speed Machining CAM software, designed to produce fast and safe CNC programs to machine mechanical parts. The word fast here means significantly
Create A Mug. Skills Learned. Settings Sketching 3-D Features. Revolve Offset Plane Sweep Fillet Decal* Offset Arc
Create A Mug Skills Learned Settings Sketching 3-D Features Slice Line Tool Offset Arc Revolve Offset Plane Sweep Fillet Decal* Tutorial: Creating A Custom Mug There are somethings in this world that have
When the machine makes a movement based on the Absolute Coordinates or Machine Coordinates, instead of movements based on work offsets.
Absolute Coordinates: Also known as Machine Coordinates. The coordinates of the spindle on the machine based on the home position of the static object (machine). See Machine Coordinates Absolute Move:
Alternatively, the solid section can be made with open line sketch and adding thickness by Thicken Sketch.
Sketcher All feature creation begins with two-dimensional drawing in the sketcher and then adding the third dimension in some way. The sketcher has many menus to help create various types of sketches.
527F CNC Control. User Manual Calmotion LLC, All rights reserved
527F CNC Control User Manual 2006-2016 Calmotion LLC, All rights reserved Calmotion LLC 21720 Marilla St. Chatsworth, CA 91311 Phone: (818) 357-5826 www.calmotion.com NC Word Summary NC Word Summary A
Touch Probe Cycles TNC 426 TNC 430
Touch Probe Cycles TNC 426 TNC 430 NC Software 280 472-xx 280 473-xx 280 474-xx 280 475-xx 280 476-xx 280 477-xx User s Manual English (en) 6/2003 TNC Model, Software and Features This manual describes
Performance. CNC Turning & Milling Machine. Conversational CAM 3.11 Instruction Manual
Performance CNC Turning & Milling Machine Conversational CAM 3.11 Instruction Manual Legacy Woodworking Machinery 435 W. 1000 N. Springville, UT 84663 Performance Axis CNC Machine 2 Content Warranty and
Computer Aided Manufacturing
Computer Aided Manufacturing CNC Milling used as representative example of CAM practice. CAM applies to lathes, lasers, waterjet, wire edm, stamping, braking, drilling, etc. CAM derives process information
Computation & Construction Lab. Stinger CNC 3D Milling Workflow
Computation & Construction Lab Stinger CNC 3D Milling Workflow 3D Single Sided Milling Guidelines - The following steps will guide the user on how to transfer digital work from a design software to setting
Kerf Bent Clock Front Geometry in MasterCAM. Open the MasterCAM application, it should look something like below.
Kerf Bent Clock Front Geometry in MasterCAM Open the MasterCAM application, it should look something like below. First thing is to figure out what you are making.using the measurements from your plans,
Lesson 4 Holes and Rounds
Lesson 4 Holes and Rounds 111 Figure 4.1 Breaker OBJECTIVES Sketch arcs in sections Create a straight hole through a part Complete a Sketched hole Understand the Hole Tool Use Info to extract information
Machinist--Cert Students apply industry standard safety practices and specific safety requirements for different machining operations.
MTT Date: 09/13/2018 TECHNOLOGY MTT Machine Tool Technology--AA Students apply industry standard safety practices and specific safety requirements for different machining operations. Students calculate
Shaft Hanger - SolidWorks
ME-430 INTRODUCTION TO COMPUTER AIDED DESIGN Shaft Hanger - SolidWorks BY: DR. HERLI SURJANHATA ASSIGNMENT Submit TWO isometric views of the Shaft Hanger with your report, 1. Shaded view of the trimetric
Prof. Steven S. Saliterman Introductory Medical Device Prototyping
Introductory Medical Device Prototyping Department of Biomedical Engineering, University of Minnesota http://saliterman.umn.edu/ You must complete safety instruction before using tools and equipment in
G02 CW / G03 CCW Circular Interpolation Motion (Group 01) - Mill
Haas Technical Documentation G02 CW / G03 CCW Circular Interpolation Motion (Group 01) - Mill Scan code to get the latest version of this document Translation Available G02 CW / G03 CCW Circular Interpolation
Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece
1 Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece In this Module, we will explore the method of adding dovetail seams to curved edges such as the circumferential edge of a
CAD/CAM/CAE Computer Aided Design/Computer Aided Manufacturing/Computer Aided Manufacturing. Part-10 CNC Milling Programming
CAD/CAM/CAE Computer Aided Design/Computer Aided Manufacturing/Computer Aided Manufacturing Part-10 CNC Milling Programming To maximize the power of modern CNC milling machines, a programmer has to master
Bottom Rail. Chapter 2. Chair. A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. B. 3D Sketch.
Chapter 2 Chair Bottom Rail A. Weldments Toolbar. Step 1. Click File Menu > New, click Part and OK. Step 2. Right click Sketch on the Command Manager toolbar and select Weldments, Fig. 1. Step 3. Click
Creo Revolve Tutorial
Creo Revolve Tutorial Setup 1. Open Creo Parametric Note: Refer back to the Creo Extrude Tutorial for references and screen shots of the Creo layout 2. Set Working Directory a. From the Model Tree navigate
Advanced CO2 car Import CAM Procedures
Advanced CO2 car Import CAM Procedures While the standard CO2 car tutorial within Quick CAM has a part that is sized to fit the billet as custom designed cars are produced this will not be the case. Before
Kerf Bent Clock Front Geometry in MasterCAM
Kerf Bent Clock Front Geometry in MasterCAM Check to make sure the nethasp is working/turned on to network. Go to ALL APPs/Mastercam x8/nethasp After the computer reads the nethasp, these programs should
Touch Probe Cycles itnc 530
Touch Probe Cycles itnc 530 NC Software 340 420-xx 340 421-xx User s Manual English (en) 4/2002 TNC Models, Software and Features This manual describes functions and features provided by the TNCs as of
Revit Structure 2014 Basics
Revit Structure 2014 Basics Framing and Documentation Elise Moss Authorized Author SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit
COMPUTER INTEGRATED MANUFACTURING LABORATORY (14AME31)
COMPUTER INTEGRATED MANUFACTURING LABORATORY (14AME31) (For III B.Tech - II SEM- Mechanical Engineering) DEPARTMENT OF MECHANICAL ENGINEERING SRI VENKATESWARA COLLEGE OF ENGINEERING & TECHNOLOGY R.V.S
CNC INTRO WALKTHROUGH GSAPP FABRICATION LAB, FALL 2017
CNC INTRO WALKTHROUGH GSAPP FABRICATION LAB, FALL 2017 this is a student guide to the procedure of gaining access to the CNC router digital fabrication equipment in the Fabrication Lab at GSAPP. The guide
Getting Started. Terminology. CNC 1 Training
CNC 1 Training Getting Started What You Need for This Training Program This manual 6 x 4 x 3 HDPE 8 3/8, two flute, bottom cutting end mill, 1 Length of Cut (LOC). #3 Center Drill 1/4 drill bit and drill
AC : IMPLEMENTATION OF CAD/CAM/CNC CURRICULUM USING MASTERCAM X SOFTWARE IN TECHNICAL PROGRAMS
AC 2008-297: IMPLEMENTATION OF CAD/CAM/CNC CURRICULUM USING MASTERCAM X SOFTWARE IN TECHNICAL PROGRAMS Farzin Heidari, Texas A&M University, Kingsville American Society for Engineering Education, 2008
FAB Professional Sheet-metal design
Page 1 of 6 FAB Professional Sheet-metal design If you use AutoCAD to create your sheet - metal fabrication drawings, you are well aware of AutoCAD's limitations. To overcome these shortcomings, Striker
Conversational CAM Manual
Legacy Woodworking Machinery CNC Turning & Milling Machines Conversational CAM Manual Legacy Woodworking Machinery 435 W. 1000 N. Springville, UT 84663 2 Content Conversational CAM Conversational CAM overview...
User s Manual Cycle Programming TNC 320. NC Software
User s Manual Cycle Programming TNC 320 NC Software 340 551-04 340 554-04 English (en) 9/2009 About this Manual The symbols used in this manual are described below. This symbol indicates that important
Estimated Time Required to Complete: 45 minutes
Estimated Time Required to Complete: 45 minutes This is the first in a series of incremental skill building exercises which explore sheet metal punch ifeatures. Subsequent exercises will address: placing
Exercise 1. Milling a Part with the Lab-Volt CNC Mill EXERCISE OBJECTIVE
Exercise 1 Milling a Part with the Lab-Volt CNC Mill EXERCISE OBJECTIVE When you have completed this exercise, you will be able to engrave text on square pieces of stock, using the Lab-Volt CNC Mill, model
Stratigraphy Modeling Boreholes and Cross. Become familiar with boreholes and borehole cross sections in GMS
v. 10.3 GMS 10.3 Tutorial Stratigraphy Modeling Boreholes and Cross Sections Become familiar with boreholes and borehole cross sections in GMS Objectives Learn how to import borehole data, construct a
Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated)
Inventor (5) Module 2: 2-1 Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated) In this tutorial, we will learn how to build a 3D model
Datum Tutorial Part: Cutter
Datum Tutorial Part: Cutter Objective: Learn to apply Datums in different ways Directions 1. Datum Axis Creation a. First we need to create a center axis for the cutter b. Model Tab > Datum > Select Axis
Box Tray Geometry in MasterCAM
Box Tray Geometry in MasterCAM First thing is to figure out what you are making. The best way is to get graph paper and draw out the tray full size or draw the pockets right on your work piece. Then you
Module 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder
Inventor (10) Module 1E: 1E- 1 Module 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder In this Module, we will explore the topic
Revit Structure 2012 Basics:
SUPPLEMENTAL FILES ON CD Revit Structure 2012 Basics: Framing and Documentation Elise Moss autodesk authorized publisher SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation Structural
Computer Numeric Control
Computer Numeric Control TA202A 2017-18(2 nd ) Semester Prof. J. Ramkumar Department of Mechanical Engineering IIT Kanpur Computer Numeric Control A system in which actions are controlled by the direct
SolidWorks Part I - Basic Tools SDC. Includes. Parts, Assemblies and Drawings. Paul Tran CSWE, CSWI
SolidWorks 2015 Part I - Basic Tools Includes CSWA Preparation Material Parts, Assemblies and Drawings Paul Tran CSWE, CSWI SDC PUBLICATIONS Better Textbooks. Lower Prices. www.sdcpublications.com Powered
File Project Data File1.TXT contains Data for creating PLAN drawing of a road section by reading Model & String from the Model files,
================================== HEADS Pro Release 14.1, User s Guide for Tutorial Data Tutorial 12B PLAN Drawings : Base Plan DXF ================================== Process: The folder Tutorial 12B
Autodesk University Inventor HSM Turning - CNC Lathe Programming
Autodesk University Inventor HSM Turning - CNC Lathe Programming So my name's Wayne Griffenberg. Please. Come on in. So I've worked in the manufacturing industry probably since 1998. Yeah, since '98. I
Chapter 2. Drawing Sketches for Solid Models. Learning Objectives
Chapter 2 Drawing Sketches for Solid Models Learning Objectives After completing this chapter, you will be able to: Start a new template file to draw sketches. Set up the sketching environment. Use various
so you want to get to know Onsrud... Onsrud1 : machine set up
so you want to get to know Onsrud... Onsrud1 : machine set up What does CNC mean? CNC: Computer Numerical Control The router is controlled by a computer, that tells the router where to go through a series
Revit Structure 2013 Basics
Revit Structure 2013 Basics Framing and Documentation Elise Moss Supplemental Files SDC P U B L I C AT I O N S Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Tutorial
NUMERICAL CONTROL.
NUMERICAL CONTROL http://www.toolingu.com/definition-300200-12690-tool-offset.html NC &CNC Numeric Control (NC) and Computer Numeric Control (CNC) are means by which machine centers are used to produce
What's New in AlibreCAM 2018 May 1, 2018
What's New in AlibreCAM 2018 May 1, 2018 This document describes new features and enhancements introduced in MecSoft s AlibreCAM 2018 product. 2018, MecSoft Corporation 1 CONTENTS AlibreCAM 2018... 3 Common
Introduction to Revolve - A Glass
Introduction to Revolve - A Glass Design & Communication Graphics 1 Object Analysis sheet Design & Communication Graphics 2 Prerequisite Knowledge Previous knowledge of the following commands are required
Stratigraphy Modeling Boreholes and Cross Sections
GMS TUTORIALS Stratigraphy Modeling Boreholes and Cross Sections The Borehole module of GMS can be used to visualize boreholes created from drilling logs. Also three-dimensional cross sections between
SinuTrain. Milling made easy with ShopMill. Training Documentation 08/2006 SINUMERIK
SinuTrain Milling made easy with ShopMill Training Documentation 08/2006 SINUMERIK 4 th and revised edition 08/2006 Valid from software version V06.04 All rights reserved Duplication or transmission of
< Then click on this icon on the vertical tool bar that pops up on the left side.
Pipe Cavity Tutorial Introduction The CADMAX Solid Master Tutorial is a great way to learn about the benefits of feature-based parametric solid modeling with CADMAX. We have assembled several typical parts