In this tutorial you will open a Dxf file and create the toolpath to remove the material contained in a closed profile.
|
|
|
- Garey Bell
- 5 years ago
- Views:
Transcription
1 Tutorial 3 - Open Dxf file and create the Pocket toolpath. In this tutorial you will open a Dxf file and create the toolpath to remove the material contained in a closed profile. Caution: CNC machines are potentially dangerous. The post-processor can output code unsuitable for your machine's control. Check the Nc file before sending it to a CNC machine.
2 1. Open the Dxf file with the "Open" button. 2. Select in "..\SimplyCam\Sample\" folder the SAMPLE_POCKET.DXF file. 3. The Info panel will appear with the info and dimension of image. Press "Next Page" button.
3 4. Define the reference point of the drawing and press "Done" button. 5. Turn in the "Off" state the button "Show grid" and "Show Axis".
4 6. The drawing is displayed in graphic area without the grid, the axis direction, the origin and the scale info.
5 7. Press "Nc Program" button to go in toolpath section. This section contain 5 pages: Page 1: File/Postprocessor definition Page 2: Tool/Operation definition Page 3: Profile/Cutter compensation selection Page 4: Cutting parameter setting Page 5: Nc file simulating or editing 8. Select the postprocessor of your Cnc machine.
6 9. Press "New" button to create new toolpath. 10. Type "test" in the Windows file dialog.
7 11. Press "Next Pg(2)" button. 12. In Tool section press "Select" button to retrieve a tool from a tool library or create a new tool.
8 13. Click in the Tool List to select the Flat tool with diameter 4. Set feeds and speed of the tool. Press the "OK" button. 14. In the Operation section, select "Pocket" and press "Next Pg(3)".
9 15. The "Profile definition" page appears. Press the "Chain" button. 16. Pick the geometry near to start point as indicate by red square.
10 17. Two yellow arrows appear. The long arrow indicate the start point of boundary and the direction of toolpath. The small arrow indicate the side of toolpath. The blue boundary is the chained profile. 18. Press the "Chain" button again to define another boundary.
11 19. Pick the new geometry such as indicate by red square. This is an island. 20. Now the island profile is chained.
12 21. Press the "Chain" button again to define another boundary. 22. Pick the geometry such as indicate by red square. This is another pocket. 23. The boundary of another pocket is chained.
13 24. Press the "Next Pg(4)" button. 25. The "Pocket parameters" page appears. Set up the following parameters: 26. Feed plane: set the height that the tool rapids to (G0) before changing to the feed rate (G1) to enter in the part (absolute).
14 27. Top of part: set the height of the piece in the Z axis (absolute). 28. Depth: set the final machining depth (absolute).
15 29. Depth increment: set the maximum amount of material to remove for each Z cut. 30. Stock to leave: set the amount of material to leave on profile; example if you need a finish pass with other tool.
16 31. Step over (%): set the spacing between each pass. This is a percentage of the cutter diameter. 32. Number of finish cuts / Finish cut size: set the number of finish pass and the amount of material to remove for each finish pass.
17 33. Spiral In-Out: "On" the toolpath spirals from the center to the external boundary of the pocket. "Off" the toolpath spirals from the external to the center of the pocket. 34. Write EOF: set this parameter for write in the Nc file the "End Of File" section (typically M2 or M30).
18 35. Press the "Calculate" button to machining the chained geometry with the cutting parameters. 36. The "Nc File" page is displayed and in the graphic area the toolpath is simulated. 37. Press the "Rewind" button.
19 38. Move the slider near to slow position. 39. Press the "Play" button to simulate the toolpath (Yellow=Rapid, Cyan=Feed) in the graphic area. 40. The "Z Depth" panel indicator, reflect the actual Z tool position (Yellow=Rapid, Cyan=Feed).
20 41. Press the "Stop" button to break the simulation. 42. Press the "Step" button many time Set the "Wireframe / Solid simulation" button on Wireframe state.
21 44. You have simulated the pocket toolpath in various mode. See below the example. 45. You have successfully created the pocket toolpath with SimplyCam. Caution: CNC machines are potentially dangerous. The post-processor can output code unsuitable for your machine's control. Check the Nc file before sending it to a CNC machine.
In this tutorial you will open a Dxf file and create the toolpath that cut the external of the part.
Tutorial 2 - Open Dxf file and create the outside Contour toolpath. In this tutorial you will open a Dxf file and create the toolpath that cut the external of the part. Caution: CNC machines are potentially
Tutorial 4 - Open Dxf file and create multiple toolpaths (Contour, Pocket and Drill).
Tutorial 4 - Open Dxf file and create multiple toolpaths (Contour, Pocket and Drill). In this tutorial you will open a Dxf file and create the toolpath that cut the external of the part, another toolpath
Kerf Bent Clock Front Toolpaths in MasterCAM. Open the MasterCAM application and open your clock front geometry file.
Kerf Bent Clock Front Toolpaths in MasterCAM Open the MasterCAM application and open your clock front geometry file. For 2D geometry such as we have, there are 2 main types of tool paths. The first one
MadCAM 2.0: Drill Pattern Toolpath
MadCAM 2.0: Drill Pattern Toolpath Digital Media Tutorial 2005-2006 MadCAM 2.0 can create a toolpath to drill holes directly into your material. The bit plunges in and out of the material without moving
ENGI 7962 Mastercam Lab Mill 1
ENGI 7962 Mastercam Lab Mill 1 Starting a Mastercam file: Once the SolidWorks models is complete (all sketches are Fully Defined), start up Mastercam and select File, Open, Files of Type, SolidWorks Files,
for Solidworks TRAINING GUIDE LESSON-9-CAD
for Solidworks TRAINING GUIDE LESSON-9-CAD Mastercam for SolidWorks Training Guide Objectives You will create the geometry for SolidWorks-Lesson-9 using SolidWorks 3D CAD software. You will be working
MasterCAM for Dresser Valet
MasterCAM for Dresser Valet Check to make sure the nethasp is working/turned on to network. Go to ALL APPs/Mastercam x8/nethasp After the computer reads the nethasp, these programs should show up. If not
VisualCAM 2018 TURN Quick Start MecSoft Corporation
2 Table of Contents About this Guide 4 1 About... the TURN Module 4 2 Using this... Guide 4 3 Useful... Tips 5 Getting Ready 7 1 Running... VisualCAM 2018 7 2 About... the VisualCAD Display 7 3 Launch...
Flip for User Guide. Inches. When Reliability Matters
Flip for User Guide Inches by When Reliability Matters Mastercam HSM Performance Pack Tutorial 1 Mastercam HSM Performance Pack Tutorial Tutorial I... 2 Getting started... 2 Tools used... 2 Roughing...
10 x 16 Cutting Board - Juice Groove in MasterCAM
10 x 16 Cutting Board - Juice Groove in MasterCAM Check to make sure the nethasp is working/turned on to network. Go to ALL APPs/Mastercam x8/nethasp After the computer reads the nethasp, these programs
Digital Media Tutorial Written By John Eberhart
MadCAM MadCAM 5.0: Large 4.1: Large & Medium CNC Tool CNC Path Tool Path Generator Generator Digital Media Tutorial Written By John Eberhart MadCAM is a tool path generator that works inside Rhino. It
Figure 1: NC Lathe menu
Click To See: How to Use Online Documents SURFCAM Online Documents 685)&$0Ã5HIHUHQFHÃ0DQXDO 5 /$7+( 5.1 INTRODUCTION The lathe mode is used to perform operations on 2D geometry, turned on two axis lathes.
Projects. 5 For each component, produce a drawing showing the intersection BO.O. C'BORE 18 DIA x 5 DEEP FROM SECTION ON A - A
Projects ~ Figure Pl Project 1 If you have worked systematically through the assignments in this workbook, you should now be able to tackle the following milling and turning projects. It is suggested that
MasterCAM for Sculpted Bench
MasterCAM for Sculpted Bench Check to make sure the nethasp is working/turned on to network. Go to ALL APPs/Mastercam x8/nethasp After the computer reads the nethasp, these programs should show up. If
Fusion 360 Part Setup. Tutorial
Fusion 360 Part Setup Tutorial Table of Contents MODEL SETUP CAM SETUP TOOL PATHS MODEL SETUP The purpose of this tutorial is to demonstrate start to finish, importing a machineable part to generating
MACH3 TURN ARC MOTION 6/27/2009 REV:0
MACH3 TURN - ARC MOTION PREFACE This is a tutorial about using the G2 and G3 g-codes relative to Mach3 Turn. There is no simple answer to a lot of the arc questions posted on the site relative to the lathe.
Flip for User Guide. Metric. When Reliability Matters
Flip for User Guide Metric by When Reliability Matters Mastercam HSM Performance Pack Tutorial 1 Mastercam HSM Performance Pack Tutorial Tutorial I... 2 Getting started... 2 Tools used... 2 Roughing...
Performance. CNC Turning & Milling Machine. Conversational CAM 3.11 Instruction Manual
Performance CNC Turning & Milling Machine Conversational CAM 3.11 Instruction Manual Legacy Woodworking Machinery 435 W. 1000 N. Springville, UT 84663 Performance Axis CNC Machine 2 Content Warranty and
Tutorial 1 getting started with the CNCSimulator Pro
CNCSimulator Blog Tutorial 1 getting started with the CNCSimulator Pro Made for Version 1.0.6.5 or later. The purpose of this tutorial is to learn the basic concepts of how to use the CNCSimulator Pro
Optimization of Cycle Time through Mastercam Virtual Simulation and Four Axis CNC Milling Machining of Camshaft
ISSN: 2454-132X Impact factor: 4.295 (Volume2, Issue6) Available online at: www.ijariit.com Optimization of Cycle Time through Mastercam Virtual Simulation and Four Axis CNC Milling Machining of Camshaft
Figure 1: NC EDM menu
Click To See: How to Use Online Documents SURFCAM Online Documents 685)&$0Ã5HIHUHQFHÃ0DQXDO 6 :,5(('0 6.1 INTRODUCTION SURFCAM s Wire EDM mode is used to produce toolpaths for 2 Axis and 4 Axis EDM machines.
Using Siemens NX 11 Software. The connecting rod
Using Siemens NX 11 Software The connecting rod Based on a Catia tutorial written by Loïc Stefanski. At the end of this manual, you should obtain the following part: 1 Introduction. Start NX 11 and open
LinuxCNC Help for the Sherline Machine CNC System
WEAR YOUR SAFETY GLASSES FORESIGHT IS BETTER THAN NO SIGHT READ INSTRUCTIONS BEFORE OPERATING LinuxCNC Help for the Sherline Machine CNC System LinuxCNC Help for Programming and Running 1. Here is a link
Box Tray Geometry in MasterCAM
Box Tray Geometry in MasterCAM First thing is to figure out what you are making. The best way is to get graph paper and draw out the tray full size or draw the pockets right on your work piece. Then you
CNC Router Part 2 Training Tutorial
CNC Router Part 2 Training Tutorial Prepared by Steve Pilon - Version 1.1 September 2017 A Index B - Intro A- Index B- Intro C- Objective D- Required Items E- Opening CamBam and Loading a DXF F- Preparing
EASY CNC. Table of Contents
Square 1 Electronics announces its new book by David Benson, "Easy CNC", A Beginner's Guide to CNC" The complete table of contents follows: This book was written by David Benson (8-1/2 x 11", 200 pages,
CNC Turning Training CNC MILLING / ROUTING TRAINING GUIDE. Page 1
CNC Turning Training www.denford.co.uk Page 1 Table of contents Introduction... 3 Start the VR Turning Software... 3 Configure the software for the machine... 4 Load your CNC file... 5 Configure the tooling...
Conversational Programming. Alexsys Operator Manual
Conversational Programming Alexsys Operator Manual Alexsys Operator Manual 1. Overview ALEXSYS is a programming system for CNC machining centers. That combines features of CAD / CAM systems with typical
Prismatic Machining Preparation Assistant
Prismatic Machining Preparation Assistant Overview Conventions What's New Getting Started Open the Design Part and Start the Workbench Automatically Create All Machinable Features Open the Manufacturing
FAB Professional Sheet-metal design
Page 1 of 6 FAB Professional Sheet-metal design If you use AutoCAD to create your sheet - metal fabrication drawings, you are well aware of AutoCAD's limitations. To overcome these shortcomings, Striker
Purdue AFL. CATIA CAM Process Reference Rev. B
Purdue AFL CATIA CAM Process Reference Rev. B Revision Notes Revision - of this document refers to the CATIA v5r21 deployment of the AFL CATIA Environment. All information contained in this reference document
Conversational CAM Manual
Legacy Woodworking Machinery CNC Turning & Milling Machines Conversational CAM Manual Legacy Woodworking Machinery 435 W. 1000 N. Springville, UT 84663 2 Content Conversational CAM Conversational CAM overview...
Kerf Bent Clock Front Geometry in MasterCAM. Open the MasterCAM application, it should look something like below.
Kerf Bent Clock Front Geometry in MasterCAM Open the MasterCAM application, it should look something like below. First thing is to figure out what you are making.using the measurements from your plans,
Using Surfcam to Produce a Numeric Control (NC) Program Part #1 Surfcam Demonstration Version Use
Using Surfcam to Produce a Numeric Control (NC) Program Part #1 Surfcam Demonstration Version Use An Introduction to the CAD/CAM Process Instructions for 3 Axis Programming Using the D&M CNC Milling Machine
Pro/NC. Prerequisites. Stats
Pro/NC Pro/NC tutorials have been developed with great emphasis on the practical application of the software to solve real world problems. The self-study course starts from the very basic concepts and
SolidCAM imachining. imachining Tool paths
SolidCAM imachining SolidCAM imachining is an intelligent High Speed Machining CAM software, designed to produce fast and safe CNC programs to machine mechanical parts. The word fast here means significantly
Kerf Bent Clock Front Geometry in MasterCAM
Kerf Bent Clock Front Geometry in MasterCAM Check to make sure the nethasp is working/turned on to network. Go to ALL APPs/Mastercam x8/nethasp After the computer reads the nethasp, these programs should
Standard. CNC Turning & Milling Machine Rev 1.0. OM5 Control Software Instruction Manual
Standard CNC Turning & Milling Machine Rev 1.0 OM5 Control Software Instruction Manual Legacy Woodworking Machinery 435 W. 1000 N. Springville, UT 84663 Standard CNC Machine 2 Content Warranty and Repair
Estimated Time Required to Complete: 45 minutes
Estimated Time Required to Complete: 45 minutes This is the first in a series of incremental skill building exercises which explore sheet metal punch ifeatures. Subsequent exercises will address: placing
Exercise 1. Milling a Part with the Lab-Volt CNC Mill EXERCISE OBJECTIVE
Exercise 1 Milling a Part with the Lab-Volt CNC Mill EXERCISE OBJECTIVE When you have completed this exercise, you will be able to engrave text on square pieces of stock, using the Lab-Volt CNC Mill, model
CAMWorks How To Create CNC G-Code for CO2 Dragsters
Objective: In this chapter we will show how to mill out the axle holes for this CO2 Dragster from the left side. VI.1. Open the previously created file: Dragster axle hole 001.sldprt. VI.2. Select the
STATE UNIVERSITY OF NEW YORK COLLEGE OF TECHNOLOGY CANTON, NEW YORK COURSE OUTLINE MECH 223 INTRODUCTION TO COMPUTER NUMERICAL CONTROL
STATE UNIVERSITY OF NEW YORK COLLEGE OF TECHNOLOGY CANTON, NEW YORK COURSE OUTLINE MECH 223 INTRODUCTION TO COMPUTER NUMERICAL CONTROL Prepared by: Daniel Miller Updated by: Daniel Miller (April 2015)
CNC Machinery. Module 5: CNC Programming / Milling. IAT Curriculum Unit PREPARED BY. August 2009
CNC Machinery Module 5: CNC Programming / Milling PREPARED BY IAT Curriculum Unit August 2009 Institute of Applied Technology, 2009 ATM313-CNC Module 5: CNC Programming / Milling Module Objectives: 1.
Prasanth. Lathe Machining
Lathe Machining Overview Conventions What's New? Getting Started Open the Part to Machine Create a Rough Turning Operation Replay the Toolpath Create a Groove Turning Operation Create Profile Finish Turning
CAMWorks How To Create CNC G-Code for CO2 Dragsters
Creating the Left Side Smooth Finish Tool Path. This chapter will focus on the steps for creating the left side smooth finish tool path. The objective of this chapter is to create to an accurate and highly
Revit Structure 2014 Basics
Revit Structure 2014 Basics Framing and Documentation Elise Moss Authorized Author SDC P U B L I C AT I O N S Better Textbooks. Lower Prices. www.sdcpublications.com Powered by TCPDF (www.tcpdf.org) Visit
What s new in IGEMS R9
General changes and CAD-commands What s new in IGEMS R9 Page 1 General changes and CAD-commands What s new in IGEMS R9 This document is not a complete manual. It describes only the differences between
Lesson 16 Helical Sweeps and Annotations
Lesson 16 Helical Sweeps and Annotations Figure 16.1 Helical Compression Spring Drawing OBJECTIVES Create a helical compression spring with a Helical Sweep Use sweeps to create hooks on extension springs
Alibre Design Tutorial - Simple Extrude Step-Pyramid-1
Alibre Design Tutorial - Simple Extrude Step-Pyramid-1 Part Tutorial Exercise 4: Step-Pyramid-1 [text version] In this Exercise, We will set System Parameters first. Then, in sketch mode, outline the Step
Getting Started. Before You Begin, make sure you customized the following settings:
Getting Started Getting Started Before getting into the detailed instructions for using Generative Drafting, the following tutorial aims at giving you a feel of what you can do with the product. It provides
When the machine makes a movement based on the Absolute Coordinates or Machine Coordinates, instead of movements based on work offsets.
Absolute Coordinates: Also known as Machine Coordinates. The coordinates of the spindle on the machine based on the home position of the static object (machine). See Machine Coordinates Absolute Move:
Creo Revolve Tutorial
Creo Revolve Tutorial Setup 1. Open Creo Parametric Note: Refer back to the Creo Extrude Tutorial for references and screen shots of the Creo layout 2. Set Working Directory a. From the Model Tree navigate
Machining Features/Regions
R CAM / -A T C A S Typically, a -Axis job will start with a Horizontal Roughing opera on to remove excess stock material in prepara on for one or more finishing passes. Therefore the Horizontal Roughing
Toothbrush Holder Project 2D Machining
Toothbrush Holder Project 2D Machining Prerequisite Toothbrush Holder drawn and saved as a DXF file in SolidWorks Focus of the Lesson On completion of this exercise you will have: Used the Techsoft 2D
What's New in RhinoCAM 2018
What's New in RhinoCAM 2018 Dec 12 This document describes new features and enhancements introduced in MecSoft s RhinoCAM 2018 product. 2018, MecSoft Corporation 1 CONTENTS RhinoCAM 2018... 3 Common Enhancements...
Revit Structure 2012 Basics:
SUPPLEMENTAL FILES ON CD Revit Structure 2012 Basics: Framing and Documentation Elise Moss autodesk authorized publisher SDC PUBLICATIONS www.sdcpublications.com Schroff Development Corporation Structural
Revit Structure 2013 Basics
Revit Structure 2013 Basics Framing and Documentation Elise Moss Supplemental Files SDC P U B L I C AT I O N S Schroff Development Corporation Better Textbooks. Lower Prices. www.sdcpublications.com Tutorial
Design & Manufacturing II. The CAD/CAM Labs. Lab I Process Planning G-Code Mastercam Lathe
2.008 Design & Manufacturing II The CAD/CAM Labs Lab I Process Planning G-Code Mastercam Lathe Lab II Mastercam Mill Check G-Code Lab III CNC Mill & Lathe Machining OBJECTIVE BACKGROUND LAB EXERCISES DELIVERABLES
Dual clip mould In the following exercise you will create a full 2 cavity mould of your dual clip mould component.
Dual clip mould 2018 In the following exercise you will create a full 2 cavity mould of your dual clip mould component. The mould is required to be a 2 cavity mould and must contain all the necessary detail
Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated)
Inventor (5) Module 2: 2-1 Module 2: Radial-Line Sheet-Metal 3D Modeling and 2D Pattern Development: Right Cone (Regular, Frustum, and Truncated) In this tutorial, we will learn how to build a 3D model
Computation & Construction Lab. Stinger CNC 3D Milling Workflow
Computation & Construction Lab Stinger CNC 3D Milling Workflow 3D Single Sided Milling Guidelines - The following steps will guide the user on how to transfer digital work from a design software to setting
Controlled Machine Tools
ME 440: Numerically Controlled Machine Tools CNCSIMULATOR Choose the correct application (Milling, Turning or Plasma Cutting) CNCSIMULATOR http://www.cncsimulator.com Teaching Asst. Ergin KILIÇ (M.S.)
Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece
1 Module 1C: Adding Dovetail Seams to Curved Edges on A Flat Sheet-Metal Piece In this Module, we will explore the method of adding dovetail seams to curved edges such as the circumferential edge of a
Advanced CO2 car Import CAM Procedures
Advanced CO2 car Import CAM Procedures While the standard CO2 car tutorial within Quick CAM has a part that is sized to fit the billet as custom designed cars are produced this will not be the case. Before
Name: Date Completed: Basic Inventor Skills I
Name: Date Completed: Basic Inventor Skills I 1. Sketch, dimension and extrude a basic shape i. Select New tab from toolbar. ii. Select Standard.ipt from dialogue box by double clicking on the icon. iii.
RDworks and Basic Rabbit Laser Operation Tutorial
RDworks and Basic Rabbit Laser Operation Tutorial File Setup Layer color is how the Rabbit Software designates different operations so, regardless of design software, you will want to organize geometry
Kitchen and Bath Design Tutorial
Adding Cabinets Chapter 5: Kitchen and Bath Design Tutorial This tutorial continues where the Materials Tutorial left off. You should save this tutorial using a new name to archive your previous work.
Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1
Alibre Design Tutorial: Loft, Extrude, & Revolve Cut Loft-Tube-1 Part Tutorial Exercise 5: Loft-Tube-1 [Complete] In this Exercise, We will set System Parameters first, then part options. Then, in sketch
Create A Mug. Skills Learned. Settings Sketching 3-D Features. Revolve Offset Plane Sweep Fillet Decal* Offset Arc
Create A Mug Skills Learned Settings Sketching 3-D Features Slice Line Tool Offset Arc Revolve Offset Plane Sweep Fillet Decal* Tutorial: Creating A Custom Mug There are somethings in this world that have
AC : IMPLEMENTATION OF CAD/CAM/CNC CURRICULUM USING MASTERCAM X SOFTWARE IN TECHNICAL PROGRAMS
AC 2008-297: IMPLEMENTATION OF CAD/CAM/CNC CURRICULUM USING MASTERCAM X SOFTWARE IN TECHNICAL PROGRAMS Farzin Heidari, Texas A&M University, Kingsville American Society for Engineering Education, 2008
< Then click on this icon on the vertical tool bar that pops up on the left side.
Pipe Cavity Tutorial Introduction The CADMAX Solid Master Tutorial is a great way to learn about the benefits of feature-based parametric solid modeling with CADMAX. We have assembled several typical parts
LAB and LAB Actions. By Mike Watson, based on publications by Harold Davis
LAB and LAB Actions By Mike Watson, based on publications by Harold Davis The goal was to improve my Star Trails images by: 1. Creating more contrast between the stars and the sky 2. Selectively adding
J. La Favre Fusion 360 Lesson 5 April 24, 2017
In this lesson, you will create a funnel like the one in the illustration to the left. The main purpose of this lesson is to introduce you to the use of the Revolve tool. The Revolve tool is similar to
The ShopBot Indexer. Contents
ShopBot Indexer Page -1- The ShopBot Indexer The ShopBot Indexer is basically a lathe with an extra level of precision built in you can precisely control the rotation of the headstock and also link it
Lesson 4 Holes and Rounds
Lesson 4 Holes and Rounds 111 Figure 4.1 Breaker OBJECTIVES Sketch arcs in sections Create a straight hole through a part Complete a Sketched hole Understand the Hole Tool Use Info to extract information
3300M CNC Control Canned cycles
3300M CNC Control Canned cycles Pocketing Canned Cycles Note The pockets marked with * all have cutter compensation built into them, so all dimension are as show on print. 1.Face. 2.Rectangular profile.*
Intro to CO 2 Laser Cutting
MAKERSPACE Intro to CO 2 Laser Cutting What Can I Do With the CO 2 Laser? CO 2 laser cutters and engravers are excellent for making precise 2-dimensional cuts in a variety of materials, as well as engraving
84 part video tutorial training course. The course is 100% free with no catches or exclusions. You don
Please Note: If you're new to Revit, you may be interested in my " Beginner's Guide to Revit Architecture " 84 part video tutorial training course. The course is 100% free with no catches or exclusions.
Operations Manual for Machines Equipped with a Rotary Axis Supplement to the WinCNC Operations Manual. 6/1/2015 Laguna Tools
Operations Manual for Machines Equipped with a Rotary Axis Supplement to the WinCNC Operations Manual 6/1/2015 Laguna Tools TABLE OF CONTENTS Overview... 3 Safety Warning... 3 Preliminary Checks... 4 Verify
CAD Tutorial 24: Step by Step Guide
CAD TUTORIAL 24: Step by step CAD Tutorial 24: Step by Step Guide Level of Difficulty Time Approximately 40 50 minutes Lesson Objectives To understand the basic tools used in SketchUp. To understand the
File Project Data File1.TXT contains Data for creating PLAN drawing of a road section by reading Model & String from the Model files,
================================== HEADS Pro Release 14.1, User s Guide for Tutorial Data Tutorial 12B PLAN Drawings : Base Plan DXF ================================== Process: The folder Tutorial 12B
General Measurement (CALSA) Part
General Measurement (CALSA) Part Contests Contests 1. How to set Part conditions...1 1.1 Setting conditions... 1 1.2 Setting measurement origin and oscillation/spin conditions... 7 General Measurement
CAMWorks How To Create CNC G-Code for CO2 Dragsters. III.1. Save the rough tool path for the bottom of the CO2 Dragster as Dragster bottom 001 rough.
In this chapter we will create the smooth G-Code tool path for the bottom of our CO2 Dragster. The smooth tool path is necessary to create a finish that requires minimal work to for the designer to later
CAD/CAM Software & High Speed Machining
What is CAD/CAM Software? Computer Aided Design. In reference to software, it is the means of designing and creating geometry and models that can be used in the process of product manufacturing. Computer
Welcome to SPDL/ PRL s Solid Edge Tutorial.
Smart Product Design Product Realization Lab Solid Edge Assembly Tutorial Welcome to SPDL/ PRL s Solid Edge Tutorial. This tutorial is designed to familiarize you with the interface of Solid Edge Assembly
Module 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder
Inventor (10) Module 1E: 1E- 1 Module 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder In this Module, we will explore the topic
CNC INTRO WALKTHROUGH GSAPP FABRICATION LAB, FALL 2017
CNC INTRO WALKTHROUGH GSAPP FABRICATION LAB, FALL 2017 this is a student guide to the procedure of gaining access to the CNC router digital fabrication equipment in the Fabrication Lab at GSAPP. The guide
Siemens NX11 tutorials. The angled part
Siemens NX11 tutorials The angled part Adaptation to NX 11 from notes from a seminar Drive-to-trial organized by IBM and GDTech. This tutorial will help you design the mechanical presented in the figure
AUTODESK INVENTOR Trial Projects
AUTODESK INVENTOR Trial Projects Drawing Creation Create detailed drawings of a collar flange PART 1: CREATING DRAWING VIEWS page: 2 1. 2. 3. Start by clicking the Projects icon in the ribbon. Navigate
Advance Steel. Tutorial
Advance Steel Tutorial Table of contents About this tutorial... 7 How to use this guide...9 Lesson 1: Creating a building grid...10 Step 1: Creating an axis group in the X direction...10 Step 2: Creating
Recovering highlight detail in over exposed NEF images
Recovering highlight detail in over exposed NEF images Request I would like to compensate tones in overexposed RAW image, exhibiting a loss of detail in highlight portions. Response Highlight tones can
Chapter 2. Drawing Sketches for Solid Models. Learning Objectives
Chapter 2 Drawing Sketches for Solid Models Learning Objectives After completing this chapter, you will be able to: Start a new template file to draw sketches. Set up the sketching environment. Use various
Machinist--Cert Students apply industry standard safety practices and specific safety requirements for different machining operations.
MTT Date: 09/13/2018 TECHNOLOGY MTT Machine Tool Technology--AA Students apply industry standard safety practices and specific safety requirements for different machining operations. Students calculate
Datum Tutorial Part: Cutter
Datum Tutorial Part: Cutter Objective: Learn to apply Datums in different ways Directions 1. Datum Axis Creation a. First we need to create a center axis for the cutter b. Model Tab > Datum > Select Axis
What's New in AlibreCAM 2018 May 1, 2018
What's New in AlibreCAM 2018 May 1, 2018 This document describes new features and enhancements introduced in MecSoft s AlibreCAM 2018 product. 2018, MecSoft Corporation 1 CONTENTS AlibreCAM 2018... 3 Common
Cube in a cube Fusion 360 tutorial
Cube in a cube Fusion 360 tutorial n Before using these instructions, it is helpful to watch this video screencast of the CAD drawing actually being done in the software. Click to link to the video tutorial.
SDC. AutoCAD LT 2007 Tutorial. Randy H. Shih. Schroff Development Corporation Oregon Institute of Technology
AutoCAD LT 2007 Tutorial Randy H. Shih Oregon Institute of Technology SDC PUBLICATIONS Schroff Development Corporation www.schroff.com www.schroff-europe.com AutoCAD LT 2007 Tutorial 1-1 Lesson 1 Geometric
Sorcerer and Warlock. Tutorial. Advanced Software for Roof and Wall Design and Estimating. Completing a mono-ridge metal roof with roof lights.
Sorcerer and Warlock Advanced Software for Roof and Wall Design and Estimating Tutorial Completing a mono-ridge metal roof with roof lights. Revision: 1.1 24 August 2009 Metric Units 2 Contents Tutorial
Modeling an Airframe Tutorial
EAA SOLIDWORKS University p 1/11 Difficulty: Intermediate Time: 1 hour As an Intermediate Tutorial, it is assumed that you have completed the Quick Start Tutorial and know how to sketch in 2D and 3D. If
CNC PART 2 : STARTING 3D GSAPP FABRICATION LAB 2016
CNC PART 2 : STARTING 3D GSAPP FABRICATION LAB 2016 this is a the second part of a student guide for skill-building and proficiency in the use of the CNC machines in the Fabrication Lab at Columbia GSAPP...upon