Kmart Tyre & Auto Service Revitalisation Program External Signage Guidelines

Transcription

1 Kmart Tyre & Auto Service Revitalisation Program External Signage Guidelines Issue 1, 18 February 2011 diadem.com.au diadem.co.nz

2 Section 1 Signwritten Graphics

3 FINISHES SCHEDULE 1.1 FINISHES COLOUR CODE DESCRIPTION COLOUR CODE PAINT 1 LIGHT BLUE PMS 639 P1 TAUBMANS LIGHT BLUE FINISHES 1. REFER TO TAUBMANS PAINT SPEC IN APPENDIX A 2 KMART BLUE 3 KMART RED PMS 300 PMS 032 P2 N/A TAUBMANS KMART BLUE 2. PAINTING CONTRACTOR REQUIRED TO PROVIDE A TOUCH UP KIT FOR EACH SITE CONTAINING THE FOLLOWING: TAUBMANS EXTERNAL WHITE 1 X 4 LITRE TIN TAUBMANS INTERNAL WHITE 1 X 4 LITRE TIN ALL OTHER COLOURS 1 X 1 LITRE TIN 4 LIGHT GREY PMS COOL GREY 3 P4 TAUBMANS LIGHT GREY 5 MID GREY PMS COOL GREY 6 P5 TAUBMANS MID GREY 6 DARKEST GREY PMS COOL GREY 9 P6 TAUBMANS DARKEST GREY 7 DARK BLUE PMS 301 P7 TAUBMANS DARK BLUE 8 WOKSHOP WALLS N/A P8 TAUBMANS WORKSHOP WALLS 9 EXTERIOR WHITE PMS 9043 P9 TAUBMANS EXTERIOR WHITE 10 INTERIOR WHITE N/A P10 TAUBMANS INTERIOR WHITE 11 DARK GREY PMS COOL GREY 8 P11 TAUBMANS DARK GREY A4 APPROVAL ITALISATION PROGRAM 01 FINISHES FINISHES

4 1.2 MOTION BLADES SETOUT MOTION BLADES SETOUT 1.DIMENSIONS GIVEN ARE PROPORTIONAL AND WILL VARY FROM SITE TO SITE DEPENDING ON THE HEIGHT OF THE BUILDING WALL 0.42X 2. BLADES ALWAYS SLOPE FROM BOTTOM LEFT TO TOP RIGHT AT 66 DEGREES FROM HORIZONTAL 3. THE RADIUSED CORNER IS CREATED BY DRAWING GUIDES PARALLEL TO THE HORIZONTAL AND 66 DEGREE LINE. THE INTERSECTION OF THESE LINES IS THE CENTRE OF THE RADIUS X 0.166X 0.166X R 0.166X 66º 0.43X 0.28X MOTION BLADES SETOUT A4 APPROVAL ITALISATION PROGRAM 01 MOTION BLADES SETOUT MOTION BLADES

5 1.3 MOTION GRAPHICS SETOUT BACK OF BUILDING LEFT SIDE OF BUILDING FRONT OF BUILDING COLOUR: P1 LIGHT BLUE COLOUR: P2 KMART BLUE REAR CORNER OF BUILDING FRONT CORNER OF BUILDING TOP OF WALL 66º BOTTOM OF WALL COLOUR: P4 LIGHT GREY (BLADES CONTINUE REF TO SITE DOC) COLOUR: P2 KMART BLUE COLOUR: P5 MID GREY COLOUR: P11 DARK GREY COLOUR: P4 LIGHT GREY COLOUR: P9 EXTERIOR WHITE MOTION GRAPHICS TYPICAL RHS RECEPTION SITE NOTE: GRAPHICS SHOWN ARE TO BE USED FOR SCALING AND TYPICAL RULES ONLY. REFER TO SITE DRAWINGS FOR SITE SPECIFIC GRAPHIC AND SIGNAGE LAYOUT. MOTION GRAPHICS SETOUT 1.GRAPHICS TO BE D IN PROPORTION TO BUILDING WALL HEIGHT 2. SET OUT BASED ON A 13 UNIT HIGH GRID DEGREE ANGLE ALWAYS TO BE USED A4 APPROVAL ITALISATION PROGRAM 01 MOTION GRAPHICS SETOUT MOTION GRAPHICS

6 1.4 DESCRIPTORS FRONT 13.85x DESCRIPTORS FRONT 1.DESCRIPTORS TO BE ALIGN WITH TOP OF BLUE SIGN WRITTEN BLADES 8.5x 2.DESCRIPTORS TO BE D PROPORTIONALLY TO THE AVAILABLE SPACE BETWEEN GARAGE OPENINGS AND TOP OF BUILDING WALL DEGREE ANGLE ALWAYS TO BE USED 66º 4. DISTANCE BETWEEN DESCRIPTORS AND MOTION GRAPHICS TO EQUAL DISTANCE BETWEEN LARGE MOTION GRAPHIC BLADES x x X X COLOUR: P6 DARKEST GREY Y 0.5Y Telephone , or visit us at DESCRIPTORS FRONT OF BUILDING A4 APPROVAL ITALISATION PROGRAM 01 DESCRIPTORS FRONT DESCRIPTORS

7 1.5 DESCRIPTORS BACK DESCRIPTORS BACK 1.DESCRIPTORS TO BE ALIGN WITH TOP OF FACIA SIGN AND BOTTOM OF SIGN WRITTEN BLUE BLADES 2.DESCRIPTORS TO BE D PROPORTIONALLY DEGREE ANGLE ALWAYS TO BE USED 4. DISTANCE BETWEEN DESCRIPTORS AND MOTION GRAPHICS TO EQUAL DISTANCE BETWEEN LARGE MOTION GRAPHIC BLADES 5. DISTANCE BETWEEN DESCRIPTORS AND FACIA SIGN TO BE GREATER THAN DISTANCE BETWEEN LARGE MOTION GRAPHIC BLADES COLOUR: P6 DARKEST GREY Y Y GREATER THAN Y DESCRIPTORS BACK OF BUILDING A4 APPROVAL ITALISATION PROGRAM 01 DESCRIPTORS BACK DESCRIPTORS

8 Section 2 Signage

9 2.1 LOGO ALIGNMENT LOGO ALIGNMENT 1. THE TYRE & AUTO SERVICE LOGO ELEMENT SHOULD BE VERTICALLY CENTRED WITH THE MART LETTERS 2. THE TYRE & AUTO SERVICE LOGO ELEMENT SHOULD BE HORIZONTALLY ALIGNED WITH THE RIGHT HAND EXTREMITY OF THE KMART ELEMENT LOGO ALIGNMENT A4 APPROVAL ITALISATION PROGRAM 01 DESCRIPTORS SETOUT DESCRIPTORS

10 2.2 FASCIA SIGNS POSITIONING Y 7.125M FASCIA SIGN (FS7I) GREATER THAN Y Y FASCIA SIGNS POSITIONING 1. THE TOP OF ALL FASCIA SIGNS SHOULD ALWAYS LINE UP WITH THE TOP OF THE BLUE SIGN WRITTEN MOTION BLADES. THIS IS EQUIVALENT TO 1/13TH OF THE HEIGHT OF THE BUILDING WALL. 13Y 2. WHERE THE HEIGHT OF THE WALL VARIES THE 1/13TH RULE SHOULD BE APPLIED TO THE SECTION OF WALL WHERE THE GRAPHICS ARE TO BE APPLIED ON THE FRONT OF THE BUILDING. SIDE ELEVATION 3. THE SETOFF FROM THE SIDE WALL SHOULD BE EQUAL TO THE VERTICAL SET OFF. 4. THE DISTANCE BETWEEN THE SIGN WRITTEN MOTION GRAPHICS AND THE FASCIA SIGN MUST BE GREATER THAN THE SET OFF FROM THE SIDE WALL. 5. THE DISTANCE BETWEEN THE FASCIA SIGN AND THE DESCRIPTOR GRAPHICS MUST BE GREATER THAN THE WIDTH OF THE LARGE SIGN WRITTEN MOTION BLADES. W GREATER THAN W 10.5M FASCIA SIGN (FS10I) Y Y Telephone , or visit us at 13Y FRONT ELEVATION A4 APPROVAL ITALISATION PROGRAM 01 DESCRIPTORS SETOUT DESCRIPTORS

11 2.3 PORTICO PORTICO POSITIONING 1.WHERE POSSIBLE THE PORTICO SHOULD BE CENTRED ON THE RECEPTION GLAZING Telephone , or visit us at Telephone , or visit us at PORTICO ALIGNED WITH GARAGE OPENINGS 300 LESS THAN 800 GREATER THAN 800 PORTICO POSITIONED 300MM ABOVE RECEPTION GLAZING 2. WHERE THE DISTANCE BETWEEN THE TOP OF THE GLAZING AND THE TOP OF THE GARAGE OPENING IS LESS THAN 800, THE TOP OF THE PORTICO SHOULD BE ALIGNED WITH THE TOP OF THE GARAGE OPENING. 3. WHERE THE DISTANCE BETWEEN THE TOP OF THE GLAZING AND THE TOP OF THE GARAGE OPENING IS GREATER THAN 800, THE UNDER SIDE OF THE PORTICO SHOULD BE POSITIONED 300MM ABOVE THE TOP OF THE RECEPTION GLAZING. A4 APPROVAL ITALISATION PROGRAM 01 PORTICO PORTICO

12 2.4 WORKSHOP STATUTORY SIGNS STATUTORY SIGNS POSITIONING 1. STATUTORY SIGN REQUIRED BETWEEN EACH GARAGE OPENING STATE ROAD AUTHORITY TO BE POSITIONED ON COLUMN FARTHEST FROM RECEPTION (WHERE REQUIRED) 3. NO SIGNS TO BE MOUNTED BETWEEN RECEPTION AND FIRST GARAGE OPENING 1600 FRONT ELEVATION DETAIL Telephone , or visit us at STATE ROAD AUTHORITY SIGN(S) TO BE MOUNTED TO COLUMN FARTHEST FROM RECEPTION (WHERE REQUIRED) FRONT ELEVATION STATUTORY SIGN REQUIRED BETWEEN EACH GARAGE OPENING NO SIGN TO BE INSTALLED NEXT TO RECEPTION A4 APPROVAL ITALISATION PROGRAM 01 WORKSHOP STATUTORY SIGNS STATUTORY SIGNS

13 Appendix A Taubmans Paint Specifications

14 PAINTING SCHEDULE Produced by: PPG PTY LTD Project: KMART Tyre & Auto Service EXTERIOR PAINTING SCHEDULE 5 of 5 Building element: Painted Exterior Brickwork Substrate: Code: Coat: Coat Description: Colour: Previously painted surface (water based) P14. Manufacturer: Taubmans 1 st Endure Exterior Low Sheen Acrylic 2 nd Endure Exterior Low Sheen Acrylic To be advised Building element: Painted Metal Window Frames/Security Bars Substrate: Code: Coat: Coat Description: Colour: Previously painted surface (water based) P15. Manufacturer: Taubmans 1 st PrepRight Traditional Undercoat 2 nd Ultra Enamel High Gloss 3 rd Ultra Enamel High Gloss To be advised. Building element: Graffiti Coatings Authorisation required prior to application Substrate: Code: Coat: Coat Description: Colour: Previously painted surface (water based) P16. Manufacturer: Taubmans 1 st Guardian Graffiti Shield 2 nd Guardian Graffiti Shield 3 rd Guardian Graffiti Shield (Wet on Wet) Clear Low Sheen Building element: Line Marking / Car Park Hobbs Minimum Wet Film Thickness (WFT) 375 microns Substrate: Code: Coat: Coat Description: Colour: NEW P17. Manufacturer: Taubmans One Coat White Knight Supreme Line Marking Paint To be advised. National Painting Specification 24/1/2011 Repaint / New Construction / Maintenance

15