The aileron precipitation static wick retainers are attached directly to the wing between the wingtip and aileron.
|
|
- Dwain Blair
- 5 years ago
- Views:
Transcription
1 Static Discharging GENERAL 3-60: STATIC DISCHARGING. General This section covers precipitation static wicks. Static wicks are installed on aircraft to discharge built up static electricity from the aircraft during flight. This helps reduce interference with radio systems. Micropoint static wicks are installed into static wick retainers. A. Wing Tip Precipitation Static Wicks The wing tip precipitation static wick retainers are installed to a bracket assembly. The bracket assembly is secured to a backing plate and gasket as part of the anti-collision strobe light assembly. For maintenance practices related to the forward position / anti-collision light, see Exterior Lighting section of Lights. (Refer to 33-40) B. Aileron Precipitation Static Wicks The aileron precipitation static wick retainers are attached directly to the wing between the wingtip and aileron. C. Elevator and Rudder Precipitation Static Wicks The elevator and rudder precipitation static wick retainers are attached directly to both elevators and the rudder. 7 Dec 07
2 . Maintenance Practices A. Wing Tip Precipitation Static Wicks (See Figure 3-60-) () Removal -Wing Tip Precipitation Static Wicks (c) Set BAT, BAT, and AVIONICS switches to OFF positions. Pull NAV LIGHTS, STROBE LIGHTS, and INST LIGHTS circuit breakers. Remove static wicks from retainers. () Installation - Wing Tip Precipitation Static Wicks Acquire necessary tools, equipment, and supplies. Description P/N or Spec. Supplier Purpose Ohmmeter - Any Source Check resistance. Sealant (Refer to -30) Any Source Seal static wicks to surface. Install static wicks onto both wing tips. Screw static wicks into retainers on both wing tips. NOTE No torque stripe, Loctite, or locking device required. Torque static wicks 0 to in-lb (.3 to.69 Nm). NOTE Leave an area of metal base of static wick exposed for future continuity checks. 3 Fill gaps between metal base of static wicks and wing tip surfaces with sealant. (Refer to -30) (c) Reset circuit breakers. (d) Perform Operational Test - Precipitation Static Wicks. (Refer to 3-60) 7 Dec 07
3 (3) Operational Test - Precipitation Static Wicks Using ohmmeter, confirm resistance from metal base of each static wick to exhaust tail pipe is less than 0 ohms. Using megohmmeter, confirm resistance from metal base of each static wick to tip of static wick is 6 to 00 megohms. 3 7 Dec 07
4 B. Aileron Precipitation Static Wicks (See Figure 3-60-) () Removal - Aileron Precipitation Static Wicks (c) Set BAT, BAT, and AVIONICS switches to OFF positions. Pull NAV LIGHTS, STROBE LIGHTS, and REC/INST LTS or RECOG LIGHTS circuit breakers. Remove static wicks from retainers. () Installation - Aileron Precipitation Static Wicks Acquire necessary tools, equipment, and supplies. Description P/N or Spec. Supplier Purpose Ohmmeter - Any Source Check resistance. Install static wicks onto both ailerons. Screw static wicks into retainers on both wings. Torque static wicks 0 to in-lb (.3 to.69 Nm). (c) Reset circuit breakers. (d) Perform Operational/Test - Precipitation Static Wicks. (Refer to 3-60) 4 7 Dec 07
5 C. Elevator and Rudder Precipitation Static Wicks (See Figure 3-60-) () Removal - Elevator and Rudder Precipitation Static Wicks (c) Set BAT, BAT, and AVIONICS switches to OFF positions. Pull NAV LIGHTS, STROBE LIGHTS, and REC/INST LTS or RECOG LIGHTS circuit breakers. Remove static wicks from retainers on elevators and rudder. () Installation - Elevator and Rudder Precipitation Static Wicks Acquire necessary tools, equipment, and supplies. Description P/N or Spec. Supplier Purpose Ohmmeter - Any Source Check resistance. Install static wicks onto both elevators and rudder. NOTE No torque stripe, Loctite, or locking device required. Screw static wicks into retainers on rudder and both elevators. Torque static wicks 0 to in-lb (.3 to.69 Nm). (c) Reset circuit breakers. (d) Perform Operational/Test - Precipitation Static Wicks. (Refer to 3-60) 7 Dec 07
6 Figure 3-60-: Static Discharging- Wing Tip Precipitation Static Wicks ( of 3) A B C D WING TIP (REF) LEGEND. Static Wick. Retainer DETAIL A SR_MM3_ Dec 07
7 Figure 3-60-: Static Discharging- Aileron Precipitation Static Wicks ( of 3) AFT SHEAR WEB GROUND (REF) LEGEND. Static Wick. Backing Plate 3. Retainer 4. Screw. Washer 6. Nut 7. Ground Wire DETAIL B SR_MM3_ Dec 07
8 Figure 3-60-: Static Discharging- Elevator and Rudder Precipitation Static Wicks (3 of 3) ELEVATOR (REF) DETAIL C RUDDER (REF) LEGEND. Static Wick. Retainer DETAIL D SR_MM3_ Dec 07
CIRRUS AIRPLANE MAINTENANCE MANUAL
STATIC DISCHARGING. DESCRIPTION This section covers precipitation static wicks. Static wicks are installed on aircraft to discharge built up static electricity from the aircraft during flight.this helps
More informationCIRRUS AIRPLANE MAINTENANCE MANUAL
UNIVERSAL ACCESS TRANSCEIVER. GENERAL This section covers the GDL UAT/ADS-B Transceiver. A. GDL UAT/ADS-B Transceiver - Serials w/ GDL The optionally installed GDL UAT/ADS-B Transceiver system consists
More information105" TIGER MOTH ARF INSTRUCTION MANUAL VERSION 1.0
105" TIGER MOTH ARF INSTRUCTION MANUAL VERSION 1.0 Step 1. Installation of the aileron servos 1) Mount aileron servo to servo mounting blocks with servo s screws. Install servo mounting plate with screws.
More informationCIRRUS AIRPLANE MAINTENANCE MANUAL
MODEL SR0 AUXILIARY STRUCTURE. DESCRIPTION This section describes those structural components which make up the auxiliary structure including fuselage floor structure, floor access panels, entry step,
More informationGFC 700 Automated Flight Control System
CIRRUS AIRPLANE MAINTENANCE MANUAL CHAPTER 22-10: GFC 700 AUTOMATED FLIGHT CONTROL SYSTEM GENERAL GFC 700 Automated Flight Control System 22-10: GFC 700 AUTOMATED FLIGHT CONTROL SYSTEM 1. General (See
More informationCIRRUS AIRPLANE MAINTENANCE MANUAL
DEPENDENT POSITION DETERMINING 1. GENERAL This section covers that portion of the system which provides information to determine position from sources which are mainly dependent on ground installations.
More informationGFC 700 AUTOMATED FLIGHT CONTROL SYSTEM (AFCS)
All GFC 700 AUTOMATED FLIGHT CONTROL SYSTEM (AFCS) 1. DESCRIPTION This section covers those systems and components which use inputs to the system to automatically control the flight path of the aircraft
More informationCIRRUS AIRPLANE MAINTENANCE MANUAL
PROPELLER ASSEMBLY 1. DESCRIPTION The propeller assembly consists of a hollow aluminum hub which supports the propeller blades and also houses the pitch changing mechanism. Movement of propeller blades
More informationIndependent Position Determining
GENERAL Independent Position Determining 34-40: INDEPENDENT POSITION DETERMINING 1. General This section covers that portion of the system which provides information to determine position from sources
More informationSTC GROUP LLC 480 RUDDIMAN DRIVE MUSKEGON, MICHIGAN REPORT NO: REV - TRIO AUTO PILOT INSTALLATION INSTRUCTIONS CESSNA MODEL 182
STC GROUP LLC 480 RUDDIMAN DRIVE MUSKEGON, MICHIGAN 49445 REPORT NO: 1006003 REV - TRIO AUTO PILOT INSTALLATION INSTRUCTIONS CESSNA MODEL 182 DATE: Original Issue 10 July, 2017 WRITTEN BY: Paul Odum APPROVED
More informationCIRRUS AIRPLANE MAINTENANCE MANUAL MODELS SR22 AND SR22T CHAPTER 8-10: LEVELING GENERAL. Leveling 8-10: LEVELING. 1. General
CIRRUS AIRPLANE MAINTENANCE MANUAL Leveling CHAPTER 8-10: LEVELING GENERAL 8-10: LEVELING 1. General This chapter provides information necessary to properly level the airplane for any of the various maintenance,
More informationBeechcraft Corporation BONANZA 36, A36, G36, A36TC & B36TC ILLUSTRATED PARTS CATALOG
CH-SECT-UNIT-FIG PAGE NO. DATE CH-SECT-UNIT-FIG PAGE NO. DATE 23 - CONTENTS 1 23-30-00-01 0 23-30-00-01 1 23-40-00-01 0 23-40-00-01 0A 23-40-00-01 1 23-40-00-01 2 23-60-00-01 0 23-60-00-01 1 BONANZA *
More informationRhino SD2/XD2 Mini Tote Conversion Kit
Instruction Sheet P/N 1613210 01 Description See Figure 1. The Rhino SD2/XD2 mini tote conversion kit is used when the material container includes a follower as part of the container structure. The mini
More informationC I R R U S EMERGENCY DESCRIPTION A. Emergency Locator Transmitter (ELT)
EMERGENCY 1. DESCRIPTION A. Emergency Locator Transmitter (ELT) This airplane is equipped with a self-contained ELT. The ELT transmitter is installed immediately behind the aft cabin bulkhead. The ELT
More informationConverting the MGL SERVO to a MGL CAPSTAN SERVO.
Parts supplied in kit Converting the MGL SERVO to a MGL CAPSTAN SERVO. 1 x bracket, 1 x bracket clamp, 4 x cap head screws M4 x 8 1 x nut M6, 1 x washer M6, 1 x drum, 1 x shear screw M3, 2 x grub screws
More informationSkymaster ARF F-18E Instructions Manual
Skymaster ARF F-18E Instructions Manual first: Take out the front servos mount, install front fuel tank before installing nose cone connect nose cone to fuselage by 6 screw Take out the 6 screws and Bottom
More informationMicroHAWK Accessory Guide
This guide contains instructions for how to install the following accessories on a MicroHAWK ID-20, ID-30, or ID-40 Reader, or on a MicroHAWK MV-20, MV-30, or MV-40 Smart Camera: Kit, Diffuser, MicroHAWK
More informationTIGER MOTH 120 ASSEMBLY INSTRUCTIONS
TIGER MOTH 120 ASSEMBLY INSTRUCTIONS SPECIFICATIONS Wing Span: Length: Radio: Flying Weight: 1920mm 1580mm 4 channel with 6 servos 4200g AILERON ASSEMBLY 1 Start by removing the servo cover from the bottom
More informationSTC GROUP LLC Page Ruddiman Drive PA-28 & PA-32 Trio Pro Pilot Installation Instructions North Muskegon, Michigan 49445
STC GROUP LLC Page 1 STC GROUP LLC 480 RUDDIMAN DRIVE MUSKEGON, MICHIGAN 49445 DOCUMENT NO: 1028001 REVISION D TRIO PRO PILOT INSTALLATION INSTRUCTIONS PIPER AIRCRAFT CORPORATION PA-28 AND PA-32 DATE:
More informationCIRRUS AIRPLANE MAINTENANCE MANUAL
All GFC 700 AUTOMATED FLIGHT CONTROL SYSTEM (AFCS) 1. DESCRIPTION This section covers those systems and components which use inputs to the system to automatically control the flight path of the aircraft
More informationCorvus Racer CC
Corvus Racer 540 35CC Item No:L-G035008 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio mm mm 1200sq in (77.4sqdm) 9.9-12lbs(4.5-5.5kg) 91-1.20(2C) 1.10-1.40(4C) 20-40cc
More informationService Bulletin No: Ref No: 136 Modification No: INSPECTION ATA Chapter: 57
PILATUS AIRCRAFT LTD. STANS, SWITZERLAND Service Bulletin No: 57-015 Ref No: 136 Modification No: INSPECTION ATA Chapter: 57 WING - AILERON INSTALLATION INSPECTION OF THE AILERON OUTBOARD-BEARING SUPPORT
More informationEdge 540 V3 35CC. Scheme A. Item No:L G Specifications. Flying Weight
Edge 540 V3 35CC Item No:L G035016 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio Description 76 (1930mm) 74 (1879mm) 1200sq in(77.4sqdm) 9.9 12lbs(4.5 5.5kg) 91 1.20(2C)
More informationFAA APPROVED AIRPLANE MAINTENANCE MANUAL SUPPLEMENT. Eyebrow Window Replacement
FAA APPROVED AIRPLANE MAINTENANCE MANUAL SUPPLEMENT AIRPLANE MAKE: Boeing AIRPLANE MODEL: 737-100, -200, -200C, -300, -400, -500, -600, -700, -700C, -800, -900 TO BE ADDED TO AMM CHAPTER 56-11-XX This
More informationEXTRA 330SC 60CC. Item No:H G Specifications cc gas DA50,DA60, DLE55, DLE60(twin), 3W55. Description
EXTRA 330SC 60CC Item No:H G060011 Specifications Wing Span Length Wing Area Flying Weight Gasoline Radio Description Carbon Fibre : 92" (2347mm) 84 1/2 " (2060mm) 1526.8 sq in(98.5sq dm) 16 17lbs(7300
More informationCorvus Racer Colour schemes. AeroPlus RC Copyright 2013 All Rights Reserved
Corvus Racer 540 59 Item No:A E050003 Specifications WING SPAN: 59"(1500mm) LENGTH: 54.1"(1374mm) WING AREA: 654sq.in.(42.2sq.dm.) FLYING WEIGHT: 4.6 5.3lbs(2000 2300g) Electric:Brushless outrunner 8Oz.
More information16. Wing Final Assembly and Installation
Section Objective: Installation and rigging of ailerons. Pitot tube install, and any other wing related items. Required Parts: Left aileron push rod ALA-0072, Right aileron push rod ALA-0073, Push tube
More informationThis section describes those structural components which make up the main frame including bulkheads, spar cover, and roll cage.
CIRRUS AIRPLANE MAINTENANCE MANUAL Main Frame CHAPTER 53-10: MAIN FRAME GENERAL 53-10: MAIN FRAME 1. General This section describes those structural components which make up the main frame including bulkheads,
More informationInstallation Instructions In-bottom/Out-back Cooling Kit for E3h Drives VLT FC Series FC 102, FC 103, FC 202, and FC 302
1.1 Description The in-bottom/out-back cooling kit fits the following E3h drives. It is compatible with drives mounted in Rittal TS8 cabinets with widths of 600 mm (24 in) or 800 mm (32 in). VLT HVAC Drive
More informationLS7 CHEVROLET TOP MOUNT Installation Manual For Systems with A/C #13460 / #13490
LS7 CHEVROLET TOP MOUNT Installation Manual For Systems with /C #13460 / #13490 PLESE RED LL INSTRUCTIONS EFORE INSTLLING NY COMPONENTS OF THE TRU TRC SERPENTINE SYSTEM Important: Thoroughly read the instructions,
More information96 WING SPAN SPITFIRE (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED
96 WING SPAN SPITFIRE (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED GENERAL INSTRUCTIONS Should you elect to use the recommended Door Skin, which is 1/8 mahogany plywood measuring 36 x 88. Have it cut
More informationUPPER DOOR KIT P/N APPLICATION BEFORE YOU BEGIN ITEMS MARKED (*) ARE INCLUDED IN HARDWARE KIT PN P/N Rev 01 07/14 Page 1 of 6
UPPER DOOR KIT P/N 2880609 APPLICATION RZR 900 BEFORE YOU BEGIN Read these instructions thoroughly and make sure all parts and tools are accounted for. Please retain these installation instructions for
More informationDOOR KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6. Verify accessory fitment at Polaris.com.
DOOR KIT P/N 2882528 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationE4-WM5-Y525A00 MOUNTING INSTRUCTION
RAM 2500/3500 4WD B8 5100 (Dual Steering Damper Kit) The installation of these steering dampers must be performed only by experienced and qualified personnel. Read and follow the installation instructions
More informationCREW REAR DOOR KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
CREW REAR DOOR KIT P/N 2883437 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
More informationSTC GROUP LLC 480 RUDDIMAN DRIVE NORTH MUSKEGON, MICHIGAN REPORT NO: REVISION H
STC GROUP LLC 480 RUDDIMAN DRIVE NORTH MUSKEGON, MICHIGAN 49445-2783 REPORT NO: 1006004 REVISION H TRIO AUTO PILOT PROVISIONS INSTALLATION INSTRUCTIONS 1953 CESSNA 180 THROUGH 1962 180E 1956 CESSNA 182
More informationSTC GROUP LLC 480 RUDDIMAN DRIVE MUSKEGON, MICHIGAN REPORT NO REVISION D TRIO AUTO PILOT INSTALLATION INSTRUCTIONS
STC GROUP LLC 480 RUDDIMAN DRIVE MUSKEGON, MICHIGAN 49445 REPORT NO. 1006003 REVISION D TRIO AUTO PILOT INSTALLATION INSTRUCTIONS CESSNA MODEL 182 WITH CESSNA NAVOMATIC EQUIPPED AUTO PILOT DATE: Original
More informationSERVICE BULLETIN TITLE NAVIGATION - CI COMM/GPS/XM ANTENNA REPLACEMENT (NON-WAAS ONLY)
TITLE NAVIGATION - CI2480-400 COMM/GPS/XM ANTENNA REPLACEMENT (NON-WAAS ONLY) EFFECTIVITY REASON The airplanes that follow equipped with the Garmin G1000 Nav III System: MODEL SERIAL NUMBERS 172R 17281241
More informationLS1/LS6 CHEVROLET Installation Manual For Systems without A/C #13405 / #13425
LS1/LS6 CHEVROLET Installation Manual For Systems without A/C #13405 / #13425 Billet Specialties, Inc. 500 Shawmut Avenue. La Grange, Illinois 60526 Tech Line (708) 588-0505 Fax (708) 588-7181 PLEASE READ
More informationForm No Assembly & Operating Instructions for: SAFETY PRECAUTIONS
Form No. 0230 Assembly & Operating Instructions for: 833 20300 83 2220 837 0-0008 078 SHOP PRESS Max. Capacity: 2 Ton These instructions are intended for various shop presses. Some models are shipped assembled
More informationUPPER DOOR KIT P/N
UPPER DOOR KIT P/N 2879946 Application RZR XP4 1000 Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain these installation instructions
More informationFor Fuselage Assembly.
1.Find these Parts First. 2.Take out F11, F12 For Fuselage Assembly. 3.Assemble F13 as below. Do not glue!!! 4.Assemble F4 as below. Do not glue!!! Do not glue!!! 5. Assemble F16 Do not glue!!! 6. Turn
More informationReplacement of Pitch Link Retainer and Service Improvement of the Pitch Control System. Effectivity: Helicopters manufactured prior to January, 1981
Page 1 of 12 Date: December 2, 1981 Subject: Models: Replacement of Pitch Link Retainer and Service Improvement of the Pitch Control System F-28C and 280C Effectivity: Helicopters manufactured prior to
More information23 - EFFECTIVE PAGES. Beechcraft Corporation PAGE 1 BARON B55, E55, 58 & G58 ILLUSTRATED PARTS CATALOG DATE CH-SECT-UNIT-FIG
CH-SECT-UNIT-FIG PAGE NO. DATE CH-SECT-UNIT-FIG PAGE NO. DATE 23 - CONTENTS 1 23-10-00-01 0 23-10-00-01 1 23-30-00-01 0 23-30-00-01 1 23-40-00-01 0 23-40-00-01 0A 23-40-00-01 1 23-60-00-01 0 23-60-00-01
More informationCIRRUS SR22 SB 2X R3. Service Bulletin. Issued: Revised: October 13, 2009 May 18, 2010
CIRRUS SR22 Service Bulletin Number: Issued: Revised: October 13, 2009 SNS SUBJECT: 30-10 ICE PROTECTION - AIRFOIL - Porous Panel Vent Inspection 1. COMPLIANCE Recommended: Accomplish this Service Bulletin
More informationLANDING GEAR. 1. Fit landing gear into slots on bottom of fuselage.
LANDING GEAR 1. Fit landing gear into slots on bottom of fuselage. 4. Use channel-lock pliers to press blind nuts into position (note: drilled hole should be slightly smaller than shaft of blind nut for
More informationGauge and ICM, ICM Tx, ICM TxR, and HUD Transmitter: AirHawk II Air Mask
Gauge and ICM, ICM Tx, ICM TxR, and HUD Transmitter: AirHawk II Air Mask MAINTENANCE AND REPAIR MSA 011 (L) Rev. 0 MSA 2010 Prnt. Spec. 10000005389(I) Mat. 10104244 Doc. 10104244 Standard Gauge Item P/N
More informationInstallation Instructions for Vista Air Vertically Folding Walls
Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.
More informationModel 209 Fireback Replacement
Model 209 Fireback Replacement Please read all the instructions before you begin the procedure. Confirm that you have all the necessary tools and materials. If you have any questions, technical support
More informationMXS R 30CC. Item No:L G Specifications. 67 1/2"(1720mm) (2C) (4C) 26 35cc gas DLE 30/35RA MLD35 JC30Evo.
MXS R 30CC Item No:L G030008 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio Description Covering Material Carbon Fibre : 75"(1915mm) 67 1/2"(1720mm) 1023sq in(66sq
More informationINSTALLATION & OWNER S MANUAL
Rev. O p. 1 of 16 INSTALLATION & OWNER S MANUAL V4213 BALL CAGE KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation
More informationREAR FUSELAGE ASSEMBLY
SECTION 5 Tail Attachments on Fuselage Ref Dwg 8RU-3 The rudder hinge line (HL) is parallel to the aft edge of the fuselage skin SECTION 5 - Page 1 of 9 Looking at the top of the rear fuselage. Stabilizer
More informationELECTRIC TOOL CORPORATION
Cat. No. -0 / Hex Demolition Hammer Cat. No. 0-0 Spline Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 -9-00 d 000 -9-00 d SpecialTools Require Forcing discs
More informationExtra 330LT CC. 2 Colour schemes H-G120001A ORACOVER FERRARI RED # ORACOVER WITH # ORACOVER BLACK # ORACOVER SILVER #
Extra 330LT 85-125CC Item No:A-G120001 Specs: WING SPAN: LENGTH: WING AREA: FLYING WEIGHT: ENGINE: RADIO: Description Covering Material Carbon Fibre: 111 (2833mm) 100" (2530mm) 2139sq in (138sq dm) 25.3-28lbs
More informationITEM NO. PART NO DESCRIPTION QTY.
PUMP MAINTENANCE ITEM NO. PART NO DESCRIPTION QTY. 1 52002 Center Case 1 2 52052 Back End Plate 1 3 52051 Front End Plate 1 4 55090 Octagonal Nut 1 5 53001 Idler Gear 1 6 53002 Drive Gear 1 7 28062 Bushing
More informationM4 Hex Nut [ ] M4 T-Nut 20 [20-044] Appx. 1. 3mm. 20 Series profiles (1 per hole) (1 per hole) Ordering Information
Handles & Light Duty PA 20 1 Assembly of Hinge M4x8 FHCS [24-208-4] M4 T-Nut 20 [20-044] M4 Hex Nut [24-706-4] 60 300-0 PA 20 on panel 2 Hinge positions 3-4 Clearance dimensions 5 Range of swing FOR M4
More informationInstallation Instructions
Installation Instructions For 4 foot / 1.2m Diameter Ultra-high Performance Antenna Model ADxxG-4-T2 Before Installation, please read the instructions carefully. This instruction guide covers the installation
More informationSERVICE BULLETIN. No. SB-CR-017 Rev.: - Date: Page: 1 of 7 Date: -
Page: 1 of 7 Date: - MODEL AFFECTED: SUBJECT: AIRCRAFT AFFECTED: COMPLIANCE: PS-28 Cruiser / SportCruiser / PiperSport Replacement of rivets for bolts in the area of the main landing gear attachment. All
More informationInstallation Instructions Precision Sport Shifter
Installation Instructions Precision Sport Shifter 2004 and up Pontiac GTO Part Number 45043 2010, 2005, 2004 by B&M Racing and Performance Products This B&M Precision Sport Shifter has been designed to
More informationMagnum low voltage drawout circuit breaker IEC horizontal stab cassette shutter kit (double wide A cassettes)
kit (double wide 4000 6300A cassettes) i WARNING (1) ONLY QUALIFIED ELECTRICAL PERSONNEL SHOULD BE PERMITTED TO WORK ON THE EQUIPMENT. (2) ALWAYS DE-ENERGIZE PRIMARY AND SECONDARY CIRCUITS IF A CIRCUIT
More informationSTC GROUP LLC 480 RUDDIMAN DRIVE MUSKEGON, MICHIGAN REPORT NO: G REV E TRIO AUTO PILOT INSTALLATION INSTRUCTIONS
STC GROUP LLC 480 RUDDIMAN DRIVE MUSKEGON, MICHIGAN 49445 REPORT NO: G-1006-51 REV E TRIO AUTO PILOT INSTALLATION INSTRUCTIONS CESSNA MODEL 182 WITH PREVIOUS CESSNA EQUIPPED AUTO PILOT DATE: Original Issue
More informationBOOMERANG TORUS. Aerobatic Sport Jet for 20 to 34 lbs (P80 to P160) thrust turbines.
BOOMERANG TORUS Aerobatic Sport Jet for 20 to 3 lbs (P80 to P160) thrust turbines. Specifications: Span... 83" (2209mm.) Span with Wingtip Tanks 90" (2286mm.) Length...87" (2108mm.) Weight 29 Lbs.(13.15
More informationManual for Propeller Type H40F
Manual for Propeller Type H40F Propeller Type: Propeller Serial No.: Date of Sale: Seal and signature of Manufacturer: Index 1 List of Modifications... 3 2 Description... 4 3 Specification of Helix Propeller
More informationService Manual. Chipper/Shredder - CS4210 and CS4265 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Service Manual Chipper/Shredder - CS4210 and CS4265 IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY This Service Manual is not a substitute for the Operator s Manual. You must read, understand
More informationPreparatory work. Core activity
7714100 Installing crash bars + 77 14 500 Equipment trim-level variant: OA Crash bars NOTICE Engine protection bars cannot be installed in combination with left and right protectors for engine. Preparatory
More informationCUSTOMER SERVICE - INSTRUCTION
Title: 737-300RB / 737-400SF 9G RIGID BARRIER REMOVAL / INSTALLATION INSTRUCTIONS STA 344: THE 9G RIGID BARRIER IS MADE UP OF 5 STATIC PANELS (4 OF THEM MADE FROM HONEY-COMB CORE AND FACE SHEET) AND ONE
More informationDependent Position Determining
GENERAL Dependent Position Determining 34-50: DEPENDENT POSITION DETERMINING 1. General This section covers that portion of the system which provides information to determine position from sources which
More informationSTC GROUP LLC 480 RUDDIMAN DRIVE NORTH MUSKEGON, MICHIGAN REPORT NO: REVISION A
480 RUDDIMAN DRIVE NORTH MUSKEGON, MICHIGAN 49445-2783 REPORT NO: 1006007 REVISION A TRIO AUTO PILOT INSTALLATION INSTRUCTIONS CESSNA MODEL 180F & LATER, CESSNA 185 ALL MODELS NO PREVIOUSLY INSTALLED FACTORY
More informationSERVICE BULLETIN TITLE FLIGHT CONTROLS - RUDDER AND ELEVATOR AUTOPILOT SERVO CABLE REPLACEMENT
TITLE FLIGHT CONTROLS - RUDDER AND ELEVATOR AUTOPILOT SERVO CABLE REPLACEMENT EFFECTIVITY REASON MODEL SERIAL NUMBERS 525 (M2) -0685, -0800 thru -0870 The equivalent of this service bulletin has been incorporated
More informationREPAIR INSTRUCTIONS. Cat. No Cat. No MILWAUKEE ELECTRIC TOOL CORPORATION. SDS Max Demolition Hammer. SDS Max Rotary Hammer
Cat. No. 9-0 SDS Max Demolition Hammer Cat. No. -0 SDS Max Rotary Hammer MILWAUKEE ELECTRIC TOOL CORPORATION W. LISBON ROAD BROOKFIELD, WISCONSIN 00-0 8-9-0 d 000 8-9-0 d Special Tools Require Forcing
More informationPARAVION TECHNOLOGY, INC AIRWAY AVENUE FT. COLLINS, COLORADO
PARAVION TECHNOLOGY, INC. 2001 AIRWAY AVENUE FT. COLLINS, COLORADO 80524 PR C208WS 900M For Workstation/Equipment Cabinet Cessna Model 208, 208B Airplanes Page ii of v REVISION HISTORY Revision Date Detail
More informationRYAN STA SAFETY PRECAUTIONS. "Sport Scale E-Power ARF" For Intermediate and Advanced Fliers. This radio control model is not a toy!
RYAN STA "Sport Scale E-Power ARF" For Intermediate and Advanced Fliers. SAFETY PRECAUTIONS This radio control model is not a toy! First-time builders should seek advice from people with model building
More informationGauge and ICM, ICM Tx, ICM TxR, and HUD Transmitter: AirHawk II Air Mask
Gauge and ICM, ICM Tx, ICM TxR, and HUD Transmitter: AirHawk II Air Mask MAINTENANCE AND REPAIR MSA 713 (L) Rev. 1 MSA 2017 Prnt. Spec. 10000005389(I) Mat. 10104244 Doc. 10104244 Standard Gauge Item P/N
More informationAircraft assembly and disassembly
Following instructions are related to ATEC 321(322) FAETA with wingtanks, but in general the basic methodics (besides several few differencies) is applicable also to other ATEC models. Aircraft assembly
More informationP/N D STOL CH 701 FUEL SENDER INSTALLATION KIT P/N D
P/N 221-012D Float type fuel sender unit in supplier box Use VDO Fuel Level Gauge 70-10 Ohms, turn to last page this section. FUEL SENDER INSTALLATION KIT P/N 226-451D IMPORTANT: Do not adjust or modify
More informationLS2-B891 LT2-B892 LS2-B891-05, LT2-B892-05
LS2-B891 LT2-B892 Single Needle Unison Feed Lock Stitcher Single Needle Unison Feed Lock Stitcher with Thread Trimmer Twin Needle Unison Feed Lock Stitcher Twin Needle Unison Feed Lock Stitcher with Thread
More informationInstructions for Continued Airworthiness Supplement
CESSNA AIRCRAFT COMPANY AIRCRAFT DIVISION WICHITA, KANSAS 67277 Instructions for Continued Airworthiness Supplement MODEL NO: 510 REPORT NO: ICA-510-34-00001 REPORT: GA36 & GA37 GPS ANTENNAS REPORT DATE:
More informationNMD Rev 1 2 August 1996 Page 1
FLIGHT CONTROLS - AILERON & FLAP CONTROL ROD FORK ENDS - INSPECTION 1. PLANNING INFORMATION A. Effectivity All Nomad N22 Series and N24 Series aircraft. B. Reason (1) Instances have occurred where Fork
More informationChapter 20. Standard Practices - Airframe
Chapter 20 Standard Practices - Airframe PAGE 1 Chapter 20 Table of Contents Chapter Title 20-00-00 GENERAL.................................. 3 20-10-00 STANDARD PRACTICES AIRFRAME........... 4 20-10-01
More informationPARTS LIST FOR MODEL 7000 SERIES - 17/46
ITEM PARTS LIST FOR MODEL 7000 SERIES - 17/46 1 Rotor 3 Housing 1 4 End Plate 6 Drive End Cover 1 7 Free End Cover 1 8 Timing Gear Set 1 9 Bearing, Drive End 10 Bearing, Free End 1 Lip Seal, Viton 4 13
More information18 GAUGE BRAD NAILER PARTS LIST
18 GAUGE BRAD NAILER MODEL G6045/G6046/G6047 PARTS LIST Model G6046 Model G6047 Nailer With Case Model G6045 not shown COPYRIGHT OCTOBER, 2001 BY GRIZZLY INDUSTRIAL, INC. 1821 VALENCIA ST., BELLINGHAM,
More informationBIPPMM03 (Published) Book specs- Dates: / / Lang: ENG01 Applic: PPM
BIPPMM03 (Published) Book specs- Dates: 20060412 / 20060412 / 20060412 Lang: ENG01 Applic: PPM Installing the Milnor Diaphragm in the Single Stage Press This document applies to models MP160Axx, MP1604xx,
More information第 4 页. 3. Apply instand type AB glue to the holes in the aileron and hinges. Epoxy the aileron to the wing.
TopRCModel-USA.com TopRCModel-USA.com TopRCModel-USA.com Accessory list for the installation of aileron and flap. 3. Apply instand type AB glue to the holes in the aileron and hinges. Epoxy the aileron
More informationFW / FIG Partition Kit(s) Installation Instructions
FW / FIG Partition Kit(s) Installation Instructions This instruction explains how to join 8 in. and 10 in. top piping partitions to FIG and FW merchandisers. Do not remove the shipping braces until the
More informationTECH SHEET PEM - REF / THREAD GALLING. SUBJECT: Root causes and guidelines to promote optimized fastener performance TECH SHEET
PEM - REF / THREAD GALLING SUBJECT: Root causes and guidelines to promote optimized fastener performance Introduction Occasionally, users of our self-clinching fasteners encounter thread binding issues
More informationRESolution V2 Manual
RESolution V2 Manual Note for the German Manual: Yellow Bottle thick CA Pink Bottle Med CA Blue tube 5 minute Epoxy Green tube 90 Minute Epoxy Construction of the Fuselage Step 1: Cover the plan with a
More informationPole Mount Installation Guide
Pole Mount Installation Guide (No Fine Adjustment) 495R Billerica Ave. North Billerica, MA 01862 USA Tel (978)459-8800 fax (978)459-3310 / 8814 Email: sales@radiowaves.com www.radiowaves.com IMPORTANT!
More informationClick Here to Go Back
Click Here to Go Back Fig. -94 Fig. -97 CC42D 10. Remove the cap screw securing the gear shift stopper plate pin retainer; then remove the retainer. Fig. -95 CC45D 12. Remove the link arm and account for
More informationHeritage Solar Lamp Post
Heritage Solar Lamp Post Instruction Manual 23108 Thank you very much for choosing a Nature Power product! For future reference, please complete the owner s record below: Model: Purchase Date: Save the
More informationMounting Instructions Item No.: xxx
Mounting Instructions Item No.: 271.92.xxx Wall-Beds 1 General Notes For vertical folding beds Successful and safe installation of Bed-Lift and construction of casework requires a professional skill level
More informationP.O. BOX 3090 ALBANY, GEORGIA PHONE 229/ FAX 229/ NIGHT LIGHTING SYSTEM AND VOLTAGE REGULATOR CIRCUIT INTERACTION
Rockwell service letter No. SL-AG-66 International P.O. BOX 3090 ALBANY, GEORGIA 31706-3090 PHONE 229/883-1440 FAX 229/439-9790 Service Letter No. SL-AG-66 NIGHT LIGHTING SYSTEM AND VOLTAGE REGULATOR CIRCUIT
More information4.2 - PUMP MAINTENANCE MODELS: AC, AS, WC, WS
4.2 - PUMP MAINTENANCE MODELS: AC, AS, WC, WS 4.2.1 - EXPLODED VIEW DRAWING REF NO. 1 2 4 QTY 3 1 1.5 5 ¾ HP HP HP HP HP DESCRIPTION PART # 1 CASE 1.25 x 1 NPT 018266 1 CASE 1.25 X 1 NPT 018268 1 CASE
More informationThreadlocking Adhesives
Threadlocking Adhesives Locking of Threaded Fasteners Why use a Threadlocker? threadlocking products prevent self-loosening and secure any threaded fastener against vibration and shock loads. They are
More informationINSTALLATION INSTRUCTIONS
TreadClimber INSTALLATION INSTRUCTIONS STAR TRAC FITNESS 1 of 14 635-4175 Rev: B NOTICE Installation of this product requires that 2 or more people are available to safely perform certain steps outlined
More informationHow to Mount a Moto Accessories MV Agusta F4 Hugger in Less than 30 Minutes.
How to Mount a Moto Accessories MV Agusta F4 Hugger in Less than 30 Minutes http://idealcycle.com/mv_agusta Materials and Tools: 13 10 4 1 3 2 5 11 6 15 17 14 12 9 8 16 7 1. Electric drill 2. Tap drill
More informationREVISION LIST CHAPTER 7: AIRCRAFT ALIGNMENT JIG
REVISION LIST CHAPTER 7: The following list of revisions will allow you to update the Legacy construction manual chapter listed above. Under the Action column, R&R directs you to remove and replace the
More informationSERVICE BULLETIN. No. SB-AG-45 Rev. B JUNE 1, 2007 FIN SPAR & ATTACH FITTINGS INSPECTION AND UPGRADE IMPORTANT:
THRUSH AIRCRAFT, INC. P.O. Box 3149 300 Old Pretoria Rd. Albany, GA 31706-3149 Product Support 229-883-1440 ext. 341 FAX 229-436-4856 jbays@thrushaircraft.com SERVICE BULLETIN No. SB-AG-45 Rev. B JUNE
More informationINSTALLATION MANUAL IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA MANUAL PART NUMBER:
PARTS-1 Model 24562/28562 Crane INSTALLATION MANUAL IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA 50438-0189 641-923-3711 MANUAL PART NUMBER: 99903701 Iowa Mold Tooling Co., Inc. is an Oshkosh Truck
More informationBX3230 Installation Instructions Oldsmobile Silhouette Chevy Venture
BX3230 Installation Instructions 1997-2004 Oldsmobile Silhouette 1997-2003 Chevy Venture Serial No. The headlight assembly, front fascia, horn bracket and windshield washer reservoir are removed for baseplate
More informationEXIT DEVICE OPERATION FIRE DOOR LABELS, STRIKES AND FRAME SCREWS FOR INFORMATION CALL OR VISIT RITEDOOR.COM
RECORD & LABELS WHAT THIS OWNER'S CAN DO FOR YOU It explains exactly how The Rite Door operates. It explains periodic maintenance requirements necessary to assure reliable operation. It explains simple
More information