Mandatory and Supplementary Testing Standard and Procedure for Product Marketing into China

Transcription

1 Mandatory and Supplementary Testing Standard and Procedure for Marketing into China Updated: June, 2017

2 1. MANDATORY AND SUPPLEMENTARY TESTING STANDARD AND PROCEDURE Certificate Content of Certificate Textile s and Apparel Accessories, e.g Handbag, Small Leather Goods, etc How to Show the Certificate Examples of Certificate (imported product Apparel) Examples of Certificate (imported product - Handbag) Permanent Label for Textile s and Apparel Contents of Permanent Label Example of Permanent Label (imported product Apparel): How to show the Permanent Label Mandatory Requirement - GB Classification of Textiles s Mandatory tests and requirement Mandatory Requirement-GB Classification of Textiles s Mandatory tests and requirement: Fiber Labeling and Care Labeling CCC Certification SUPPLEMENTAL TESTING STANDARD AND PROCEDURE FOR PRODUCT MARKETING INTO CHINA Apparel Knit Knit Skirt Suit Knit Casual Wear Knit T-Shirt Knit Workmanship Sweater Knit Garment and Adornment for Infant Knit Wool Goods Knit Wool Goods Knit Cashmere Goods Knit Silk or Silk Blended Garments Knit Sportswear Woven Trench coats Woven Casual Wear Jackets Jeanswear Shirts and Blouses Skirts and Skirted suit Trousers/Skirt Women s suits and coats Woven Silk Garments Woven Infant s wear Intimate Cotton Knit Underwear Knit Underwear in Synthetic Fiber

3 2.2 Accessories Belts Cold Weather Hat Glove Scarf Electrical & Electronic s Digital Camera Mouse Portable Fan Plug-in Headphone/ Plug-in Speaker Torch Bags Handbags/Backpack/Knapsack Small Leather Goods / Wallets Home s Bed Sheet / Pillow Case Bed Sheet Pillow Case Cushion/Pillow Domino Set Gumball Machine Ice Pop Tray Luggage Stainless Steel Cup/ Water Bottle Towel Umbrella Baby Changing Pads Pet Items Pet Apparel Pet Bed Pet Bowl Pet Carrier Bags Pet Collar/Leash Stationery Magnetic Poetry Kit Photo Album Pen Pencil Marker Notebook Sporting Goods Scooter (Intended for Children with a body mass 50 kg max, China) Tennis Ball Toys Cosmetics Lip gloss (for Adult) Nailpolish (for Adult)

4 1. Mandatory and Supplementary Testing Standard and Procedure ALL goods imported to China must be accompanied with Certificates, complying GB for textile products and apparel and the specified product standard. The goods without a Certificate and proper PASS test report(s) in meeting the requirement of GB and the specified product standard or with an unsatisfactory test result(s) may be rejected by customs authorities and/or held for further inspection which can lead to delays and extra costs. 1.1 Certificate All the products, which comply with GB for textile products and apparel, the specified product standard and sold in China, are required to attach qualified certificate Content of Certificate certificate includes below information: Textile s and Apparel Category A, B or C Care Instruction Name and address of manufacturer/ distributor o o o If the products made in China and sell in China directly, then the name and address of manufacturer s are required. If the products made in China and imported from other countries ( i.e classified as imported goods), the original state ( Country or Province) (i.e. Country of Origin) and name and address of agent/importer/distributor in China are required. If the products made in other countries, the original state (Country of Province) (i.e. Country of Origin) and name and address of agents/importer/distributor in China are required. Name Sizes Standard Name Fiber Content Quality Grade, e.g. Standard implies the quality guarantee claimed on the label; the different product standards for corresponding products are shown as below: Chinese National General Safety Technical Textile and Apparel Test Standard* Standard Number FZ/T GB/T GB/T GB/T GB/T GB/T GB/T GB/T Standard Name Children s clothing and student s wear Shirts and blouses Cotton wadded clothes Men's suits and coats Women's suits and coats Women and men's trousers Sizes for shirts and blouses Sizes for coats and suits 4

5 GB/T GB/T GB/T FZ/T FZ/T FZ/T FZ/T FZ/T FZ/T FZ/T FZ/T GB/T FZ/T Underwear Knitted T-shirt Textiles- Identification of fiber content Wool Knitted Good Knitted Sportswear Knitted skirt suit Skirts and skirted suit Jeanswear Casual Wear Jacket Dog apparel Towel Scarf and Shawl * The table lists out some common Standard Number and Name only, please refer to GB or China Standard for details Accessories, e.g Handbag, Small Leather Goods, etc Name and address of manufacturer o o o If the products made in China and sell in China directly, then the name and address of manufacturer s are required. If the products made in China and imported from other countries (i.e classified as imported goods), the original state (Country or Province) (i.e. Country of Origin) and name and address of agent/importer/distributor in China are required. If the products made in other countries, the original state (Country of Province) (i.e. Country of Origin) and name and address of agents/importer/distributor in China are required. Brand Name Standard Name size and specification Manufacturing date (Month & Year) materials compositions and contents color Batch Number (Style Number) Quality Grade, e.g. Certification & Certification Logo Standard implies the quality guarantee claimed on the label; the different product standards for corresponding products are shown as below: Accessories Test Standard* Standard Number QB/T QB/T QB/T QB/T GB/T QB/T QB/T Standard Name Handbag and Knapsack Wallet Leather Belt Traveling Case and Trolley Bag Umbrella Stainless Steel Water Bottle General candles * The table lists out some common Standard Number and Name only, please refer to China Standard for details 5

6 1.1.2 How to Show the Certificate Certificate is required to be presented by one of the below ways: Direct print or woven label on the products Sewn-in label, sticker or hangtag attached on the products Print on the product package Sticker on the product package; or Leaflet delivered together with the products Examples of Certificate (imported product Apparel) Kate Spade NUMU

7 Examples of Certificate (imported product - Handbag) Kate Spade PWRU Permanent Label for Textile s and Apparel According to GB Instruction for use of products of consumer interest Instructions for use of textiles and apparel, all the Textile s and Apparel sold in China are required to attach the legible label (i.e. permanent label) and be able to subject to use duration described in use instruction Contents of Permanent Label Permanent Label includes below information: a. Fiber Content (refer to FZ/T 01053) b. Sizes (refer to GB/T to GB/T ) c. Care Instruction 1. Washing Symbols (graphic symbols specified in GB/T 8685 and with their corresponding simple declaration text) 2. If symbols are not enough to explain, the short text can be added, but it shall be not in parallel with note to symbols meaning 7

8 Example of Permanent Label (imported product Apparel): Kate Spade NJMU How to show the Permanent Label The permanent label shall be permanently adhered on the suitable position of product: a) The label of size or specification i. For apparel it can be sewn in middle of the collar. For the cover coat and business suit it can also sewn on the top or down edge of inside pocket of jacket; For the trouser or skirt on the lower edge of waistband. ii. For other textile products, e.g. scarf, towel etc, can be sewn on the corners b) The label of material compositions and contents, care instruction i. The material composition and contents, care instruction can be indicated on a label together. ii. For apparel, it can be generally sewn on the lower middle position of left seam For the skirts and trouser can be sewn on the lower edge of waistband or upper position of skirt left seam, trouser side seam iii. For other textile products, e.g. scarf, towel etc, can be sewn on the corners 1.3 Mandatory Requirement - GB Chinese National General Safety Technical Code for Textile s GB is adopted by General Administration of Quality Supervision, Inspection & Quarantine of P.R.C(AQSIQ) on 27 November GB is a mandatory standard for apparel industry and standardizes general safety technical requirements for textile products, testing methods, rules of inspection, and guide for implementation and supervision. This regulation has been in effect since Year It is required to follow the latest standard of G B

9 1.3.1 Classification of Textiles s GB establishes 3 classes of textile products: Category A: s for Babies (<36 months and <= 100 cm high), e.g. Cloth diaper, pull-on nappy, underwear, bib, nightgown, gloves, socks, covering, coat, bonnet, bedding Category B: s with direct contact to skin, e.g. Bra, bellyband, vest, track suit, shirt, shorts, skirt or trousers (summer), pajamas, socks, bed sheet, bed cover Category C: s with indirect contact to skin, e.g. Sweater, overcoat, skirt, trousers, curtain, bedspread, textile wall paper, filling material, padding cloth Mandatory tests and requirement Original test reports covering standard GB must accompany the shipping documents of all orders. Areas which the mandatory tests must cover: - Formaldehyde Content - ph Value - Color Fastness to water, perspiration, rubbing - Color Fastness to saliva on baby products - Off-Flavor - AZO dyes The related requirements are summarized as below: Requirement Type A Type B Type C Formaldehyde Content (mg/kg) ph Value Colorfastn To water(change or staining in color) ess/class To acid perspiration (change or staining in color) To basic perspiration (change or staining in color) To dry rubbing To saliva (change or staining in color) Determination of odor Azo Dyestuff-produced banned aromatic amines Not Allowed <20mg/kg 9

10 1.4 Mandatory Requirement - GB Standardization Administration of China published that GB Safety technical code for infants and children textile products will come into effect on June 1, The transition period of implementation is 2 years. The product what was manufactured before June 1, 2016 and met the requirements of relevant standards, will be allowed to continue to being sold until May 31, Classification of Textiles s GB applies to infants and children s textiles sold domestically in China. It does not cover items such as soft or stuffed toys, textile craft or art work, disposable sanitary products, handbags, suitcases, backpacks, umbrellas, carpets, rugs and professional sportswear. Textile products for infants Textile products that are worn or used by infants at and below 36 months of age. Textile products for children Textile products that are worn or used by children of 3 years to 14 years of age Mandatory tests and requirement: GB includes the requirements set in GB 18401, such as the requirements for formaldehyde, ph, color fastness, odor and Azo dyes, with the addition of color fastness to wet rubbing. However GB uses the same technical class system as GB In addition to the above requirements, GB additionally requires the following: Fabrics: - Requirements of colour fastness to wet rubbing / - Heavy metal (total lead, total cadmium) and Phthalates ( See Table 1 Below) - Flammability Filling materials: - Textile fibres filling shall comply with the corresponding safety requirements of in GB Downs and feathers filling shall comply with not only the corresponding safety requirements of in GB but also the microbiological requirements specified in GB/T Mechanical Hazards: - Drawstrings/Cords, Sharp points/sharp Edges, Tensile Strength Others: - Needles and other metal sharp objects are not allowed in the package for the textile products for infants and children. 10

11 - Needles and other metal sharp objects are not allowed on the textile products for infants and children Sewing position for the permanent labels of infants products Table 1: Textile fabrics safety technical requirements for GB Category Items A B C Colour fastness to wet rubbing a / grade 3 (dark 2-3) 2-3 Heavy metals b /(mg/kg) Phthalates c /(%) Lead 90 Cadmium 100 Di(2-ethylhexyl) 0.1 phthalate (DEHP), dibutylphthalate (DBP) and benzylbutyl phthalate (BBP) Di-isononyl phthalate (DINP), 0.1 Di-n-octyl phthalate(dnop) and di-isodecyl phthalate (DIDP) Flammability d Class 1 (Normal Flammability) Note: Flame retardant finish of infant textile is not recommended. If the textile product is treated with flame retardant, the textile product shall comply with the relevant national legislation and mandatory standards. a These requirements do not apply to non-dyed and bleached products. GB/T defines a colour as 'depth' if it has a colour depth greater than 1/12 according to the colour cards of standard depths for dyeing with dyestuffs. b Only coating and pigment dyeing & printing fabrics shall be tested for total lead and cadmium mass fraction. c Only coating and pigment dyeing & printing fabrics shall be tested. d Only the shell/outer fabric materials of product shall be tested. There is no need to test fabrics made entirely from any of the following fibers or entirely from combination of the following fibers: wool, acrylic, modacrylic, nylon, olefin, polyester, and not applicable to textiles whose unit area mass are more than 90 g/m 2. 11

12 1.5 Fiber Labeling and Care Labeling The Generic name of fibers and the way to show fiber content on Fiber Label are required to follow the latest standard of Textile Designation of fiber content - FZ/T The symbols and orders of care instruction are required to follow the latest standard of Care Labeling Code for Textiles and Apparel - GB 8685 (derived from ISO 3758). 1.6 CCC Certification The State General Administration of Quality Supervision, Inspection and Quarantine of the People s Republic of China issued the Regulations for Compulsory Certification (CCC). Scope of CCC Certification - Cable and Wire - Switches for circuits, installation protective or connection devices - Low-voltage electrical apparatus - Low-voltage electrical apparatus - Fractional horse-power motors - Electric tools - Welding machines - Household and similar electrical appliances - Audio and video equipment - Information technology equipment - Lighting apparatus - Telecommunication Terminal Equipment - Motor vehicles and safety parts - Motor Vehicle Tyres - Safety Glass - Medical Devices - Detectors for intruder alarm system - Decoration and fitment product - Toy product (children aged under 15) Please find the detail in following website: 06/12/ htm CCC certification needs a long time for application (apply certification, laboratory testing, & factory audit), Vendor needs to well prepare & planning to complete before shipment. Eg. One month for laboratory testing, 2 months for factory audit, etc. 12

13 2. Supplemental Testing Standard and Procedure for Marketing into China 2.1 Apparel Knit Knit Skirt Suit TEST DESCRIPTION FIBRE CONTENT Fiber Content TEST METHOD (FZ/T 73026)-FZ/T 01053,GB/T 2910, GB/T 2911, FZ/T 01057, FZ/T 01026, FZ/T / ISO 1833 PHYSICAL PROPERTIES Bursting Strength (FZ/T 73026)-GB/T 8878 (GB/T19976) Seam Bursting Strength (FZ/T 73026)-FZ/T A Pilling Resistance (FZ/T 73026)-GB/T Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30%, and : Min 135 N, and : Min 150 N : Grade 4.0 min Grade 3.5 min DIMENSIONAL STABILITY Resistance to Torque (Spirality) (FZ/T 73026)-FZ/T item 5.2.4/ISO : Grade 3.0 min : 4.0% for top 2.0% for skirt Dimensional Stability to Washing Dimensional Stability to Drycleaning (FZ/T 73026)-GB/T8878 / ISO 6330 (FZ/T 73026)-FZ/T /ISO 3175 : 5.0% for top 3.0% for skirt Class: 6.0% for top 4.0% for skirt : -4.0% to +2.0% (Lengthwise and widthwise) & : -5.0% to +2.0% (Lengthwise and widthwise) : -1.0% to +1.0% (Lengthwise and widthwise) : -1.5% to +1.5% (Lengthwise and widthwise) : -2.0% to +2.0% (Lengthwise and widthwise) COLORFASTNESS TESTS Color Fastness to Water (FZ/T 73026)-GB/T 5713 /ISO 105 E 01 Color change: 4 Color staining: 4 Color change: 3-4 Color staining:3 Color change: 3 Color staining:3 Color Fastness to Perspiration (FZ/T 73026)-GB/T 3922 /ISO 105 E04 Color change: 4 Color staining: 4 Color change: 3-4 Color staining:3 Color change: 3 Color staining:3 13

14 TEST DESCRIPTION TEST METHOD Color Fastness to Crocking (Rubbing) (FZ/T 73026)-GB/T 3920 /ISO 105 X12 Dry: 4 Wet: 3-4 (dark color:3) Dry: 3-4 Wet: 3 (dark color:2-3) Dry: 3 Wet: 3 (dark color:2-3) (Printing) Dry: 3-4 Wet: 3 & (Printing) Dry: 3 Wet: 2 Color Fastness to Washing (FZ/T 73026)-GB/T /ISO 105 C10 Color change: 4 Color stain: 4 Color change: 3-4 Color stain: 3 Color change: 3 Color stain: 3 Color Fastness to Light (FZ/T 73026)-GB/T 8427 method 3 / ISO 105 B02 (Printing) Color change: 3-4 Color stain: 3-4 Grade 4 for dark, light & Color change: 3 Color stain: 3 Grade 4 for dark Grade 3 for light Grade 3 for dark Grade 3 for light Color Fastness to Drycleaning (For USA/Canada Only ) (FZ/T 73026)-GB/T 5711 /ISO 105 D01 Color change: 4-5 Color stain: 4-5 Color change: 4 Color stain: 4 Color change: 3-4 Color stain:

15 Knit Casual Wear TEST DESCRIPTION FIBRE CONTENT Fiber Content TEST METHOD (FZ/T 73020)-FZ/T 01053,GB/T 2910, GB/T 2911, FZ/T / ISO 1833 PHYSICAL PROPERTIES Bursting Strength (FZ/T 73020)-GB/T ,the steel ball diameter is 20mm Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30%, and : Min 135 N Pilling Resistance (FZ/T 73020)-GB/T : Grade 4.0 min Grade 3.0 min : Grade 2.5 min DIMENSIONAL STABILITY Resistance to Torque (Spirality) (FZ/T 73020)-FZ/T item /ISO : 4.0% for top 1.5% for trousers : 6.0% for top 2.5% for trousers : 8.0% for top 3.5% for trousers Dimensional Stability to Washing (Dress type is not applicable) (FZ/T 73020)-FZ/T item / ISO 6330 COLORFASTNESS TESTS Color Fastness to Water (FZ/T 73020)-GB/T 5713 /ISO 105 E 01 Color Fastness to Perspiration Color Fastness to Crocking (Rubbing) GB/T 3922 /ISO 105 E04 (FZ/T 73020)-GB/T 3920 /ISO 105 X12 : -4.0% to +2.0% (Lengthwise and widthwise) & : -5.0% to +2.0% (Lengthwise and widthwise) Mandatory in China GB Color change 3 Color staining 3 Color change: 4 Color staining: 4 Dry: 4 Wet: 3-4 (dark color:3) Color change: 3-4 Color staining:3 Dry: 3-4 Wet: 2-3 (dark color:2) Color change: 3 Color staining:3 Dry: 3 Wet: 2-3 (dark color:2) Color Fastness to Washing (FZ/T 73020)-GB/T /ISO 105 C10 (Printing) Dry: 3-4 Wet: 3 Color change: 4 Color stain: 4 & (Printing) Dry: 3 Wet: 2 Color change: 3-4 Color stain: 3 Color change: 3 Color stain: 3 Color Fastness to Light (FZ/T 73020)-GB/T 8427 method 3 / ISO 105 B02 (Printing) Color change: 3-4 Color stain: 3-4 Grade 4-5 for dark Grade 4 for light & (Printing) Color change: 3 Color stain: 3 & Grade 4 for dark Grade 3 for light 15

16 Knit T-Shirt TEST DESCRIPTION FIBRE CONTENT Fiber Content PHYSICAL PROPERTIES Bursting Strength Pilling Resistance DIMENSIONAL STABILITY Resistance to Torque (Spirality) Dimensional Stability to Washing TEST METHOD (GB/T 22849)-FZ/T 01053,GB/T 2910, GB/T 2911, FZ/T 01057, FZ/T 01026, FZ/T / ISO 1833 (GB/T 22849)-GB/T (GB/T 22849)-GB/T (GB/T 22849)-GB/T item /ISO (GB/T 22849)-GB/T8878 / ISO 6330 COLORFASTNESS TESTS Color Fastness to Water (GB/T 22849)-GB/T 5713 /ISO 105 E 01 Color Fastness to Perspiration Color Fastness to Crocking (Rubbing) (GB/T 22849)-GB/T 3922 /ISO 105 E04 (GB/T 22849)-GB/T 3920 /ISO 105 X12 Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30% All classes Min 150 N High class Grade 3.5 min High class 4.0% High class -3.0% to +1.5% (L & W) High class Color change: 4 Color staining:4 High class Color change: 4-5 Color staining:3-4 Dry: 4 Wet:: 3 1 st class Grade 3.0 min 1 st class 5.0% 1 st class -5.0% to +3.0% (L) -5.0% to +2.0% (W) 1 st class Color change: 3-4 Color staining:3-4 1 st class Color change: 3-4 Color staining:3-4 Dry: 3-4 Wet:: 2-3 Grade 2.5 min 6.0% -6.0% to +3.0% (L & W) Color change: 3 Color staining:3 Color change: 3 Color staining:3 Dry: 3 Wet:: 2-3 (dark 2) Color Fastness to Washing (GB/T 22849)-GB/T 3921.A (1)/ISO 105 C10 and 1 st class (Printing) Dry: 3 Wet: 2-3 High class Color change: 4-5 Color staining:4 1 st class Color change: 4 Color staining:3-4 (Printing) Dry: 3 Wet:: 2 Color change: 3-4 Color staining:3 Dye migration after Washing Color Fastness to Light and perspiration (GB/T 22849)-GB/T Appendix A/ISO C10 (GB/T 22849)-GB/T14576 B/ISO 105 B07 Color Fastness to Light (GB/T 22849)-GB/T 8427 method 3 / ISO 105 B02 High class (Printing) Color change: 4 Color staining:3-4 High class Cross staining: st class and qualified Cross staining: 4 High class Grade st class and qualified Grade st class (Printing) Color change: 3-4 Color staining:3 High class Grade 4 (dark, light) 1 st class and qualified Grade 4 (dark) Grade 3 (light) (Printing) Color change: 3 Color staining:3 16

17 Knit Workmanship Sweater (Apply to sweater made up of cotton, linen, silk, synthetic fiber, and its blends fabric) TEST TEST METHOD DESCRIPTION FIBRE CONTENT Fiber Content (FZ/T )- FZ/T 01053,GB/T 2910, GB/T 2911, FZ/T 01026, FZ/T 01095/ISO 1833 PHYSICAL PROPERTIES Pilling Resistance (FZ/T )- GB/T / ISO DIMENSIONAL STABILITY Dimensional Stability to Washing (FZ/T )- GB/T 8629/ ISO 6330 COLORFASTNESS TESTS Color Fastness to Water (FZ/T )- GB/T 5713 / Color Fastness to Perspiration Color Fastness to Crocking (Rubbing) Color fastness to Washing ISO 105 E 01 (FZ/T )- GB/T 3922 /ISO 105 E04 (FZ/T )- GB/T 3920 /ISO 105 X12 (FZ/T )- GB/T /ISO 105 C10 Color fastness to light (FZ/T )- GB/T 8427 method 3 / ISO 105 B02 Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30% : Grade 4 min : -4.0% to +2.0% lengthwise -3.0% to + 2.0% widthwise Color change: 4 Color staining:3-4 Color change: 4 Color staining:3-4 Dry: 4 Wet: 3 Color change: 4 Color stain: 3-4 Grade 4 for dark, Grade 3 for light : Grade 3.5 min : -5.0% to + 2.0% lengthwise -5.0% to + 4.0% widthwise 1st Class Color change: 3-4 Color staining:3 Color change: 3-4 Color staining:3 Dry: 3 Wet:2-3 Color change: 3-4 Color stain: 3 1st Class Grade 4 for dark, Grade 3 for light : Grade 3 min : -7.0% to + 2.0% lengthwise -6.0% to + 5.0% widthwise Color change: 3 Color staining:3 Color change: 3 Color staining:3 Dry: 3 Wet: 2-3(Dark 2 ) Color change:3 Color stain: 3 Grade 3 17

18 Knit Garment and Adornment for Infant (Apply to Age 36 months) TEST DESCRIPTION FIBRE CONTENT Fiber content PHYSICAL PROPERTIES Seam Strength (for cords, button) DIMENSIONAL STABILITY Dimensional stability to washing TEST METHOD (FZ/T 73025)-FZ/T 01053, GB/T 01057, FZ/T 01095, GB/T 2910, 2911/ ISO 1833 GB/T cut position as section (FZ/T 73025)-GB/T 8878 GB 8629 / ISO 6330 COLORFASTNESS TESTS Color Fastness to Water (FZ/T 73025)-GB/T 5713 /ISO 105 E 01 Color Fastness to Perspiration Color Fastness to Crocking (Rubbing) Color fastness to washing (FZ/T 73025)-GB/T 3922 /ISO 105 E04 (FZ/T 73025)-GB/T 3920 /ISO 105 X12 (FZ/T 73025)-GB/T /ISO 105 C10 Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30% : 40 N min 30 N min : -5.0% to +1.0% (Lengthwise and widthwise) : -6.0% to +2.0% (Lengthwise) -7.0% to +2.0% (Widthwise) Color change: 4 Color staining: 4 Color change: 4 Color staining: 4 Dry: 4 Wet: 3-4 (dark color:3) (Printing) Dry: 4 Wet: 3-4 (dark color: 3) Color change: 3-4 Color stain: 3-4 Color change: 3-4 Color staining:3-4 Color change: 3-4 Color staining:3-4 Dry: 4 Wet: 3 (dark color:2-3) (Printing) Dry: 4 Wet: 3 (dark color: 2-3) Color change: 3 Color stain: 3 (Printing) Color change: 3-4 Color stain: 3-4 Color change: 3 Color stain: 3 Color fastness to saliva GB/T and 1 st class Color change: 4 Color stain: 4 18

19 Knit Wool Goods (Apply to < 30 % wool blends and wool like goods) TEST DESCRIPTION FIBRE CONTENT Fiber content TEST METHOD (FZ/T 73005)-FZ/T 01053, FZ/T 01026, GB/T 2910, 2911,16988/ ISO 1833 PHYSICAL PROPERTIES Pilling resistance (FZ/T )- GB/T / ISO Variation of tolerance for products weight (%) DIMENSIONAL STABILITY Relaxation Shrinkage (only apply to plain products) FZ/T section FZ/T washing procedure 1X7A COLORFASTNESS TESTS Color Fastness to Water (FZ/T 73005)-GB/T 5713 /ISO 105 E 01 Color Fastness to Perspiration Color Fastness to Crocking (Rubbing) (FZ/T 73005)-GB/T 3922 /ISO 105 E04 (FZ/T 73005)-GB/T 3920 /ISO 105 X12 Color fastness to washing (FZ/T 73005)-GB/T A1S /ISO 105 C06 Color fastness to light (FZ/T )- GB/T 8427 method 3 / ISO 105 B02 Single fiber: 0%; 1 st class: ±3% 2 nd class ±5% : Grade 3 min 2 nd Class: Grade 2-3 min As agreement in trading : ±5.0% (Lengthwise and widthwise) Color change: 3 Color staining: 3 Color change: 3-4 Color staining: 3 Dry: 3-4 (dark 3) Wet: 2-3 Color change: 3 Color stain: 3 Grade 3-4 for dark, Grade 3 for light 19

20 Knit Wool Goods (Apply to pure wool and > 30 % wool blend goods) TEST DESCRIPTION FIBRE CONTENT Fiber content TEST METHOD (FZ/T 73018)-FZ/T 01053, FZ/T 01026, GB/T 2910, 2911,16988/ ISO 1833 Single fiber: 0%; Blend product allow wool reduce % (dry content) 1 st class: Max. 3% : Max. 5% PHYSICAL PROPERTIES Bursting Strength (FZ/T 73018) -GB/T 7742/ ISO Only apply to plain products, not apply to vest, and small garments Pilling resistance (FZ/T )- GB/T / ISO Remarks: (if one fibre less than 10%, its max. tolerance less than 30% as claimed.) High class, 1 st class, 2 nd class 323 kpa min for comb(<31.2 tex requirement: 245 kpa min) (<20.8 tex requirement: 196 kpa min 225 kpa min for card (<71.4 tex requirement: 196 kpa min) High class: Grade 3-4 min : Grade 3 min 2 nd and 3 rd Class: Grade 2-3 min Coefficient of yarn covering FZ/T High class, 1 st class, 2 nd class Minimum 1.0 (mm.tex) Weight tolerance (%) FZ/T section As agreement in trading DIMENSIONAL STABILITY Hand wash item Remarks: open shirt, vest with non milling products test relaxation and felting shrinkage, milling products test total shrinkage Relaxation Shrinkage (only apply to plain products) FZ/T washing procedure Open shirt, vest -10% (length) +5%, -8% (widthwise) Washing procedure: 1X7A Felting shrinkage FZ/T washing procedure underwear -10% (length) Washing procedure: 1X7A Open shirt, vest -8% (area) Washing procedure: 1X7A underwear -8% (area) Washing procedure: 1X5A socks -10% (length) Washing procedure: 1X7A+1X5A Small garment -8% (area) 20

21 TEST DESCRIPTION Total shrinkage Machine wash item Relaxation Shrinkage (only apply to plain products) Felting shrinkage TEST METHOD FZ/T washing procedure FZ/T washing procedure FZ/T washing procedure Washing procedure: 1X7A+1X7A Open shirt, vest -10% (length) -5% (widthwise) -8% (area) Washing procedure: 2X7A Trousers, skirt -5% (length), +5% (widthwise) Washing procedure: 2X7A Open shirt, vest -10% (length) +5%, -8% (widthwise) Washing procedure: 1X7A underwear -10% (length) +5% (widthwise) Washing procedure: 1X7A Open shirt, vest -8% (area) Washing procedure: 2X5A underwear -8% (area) Washing procedure: 5X5A socks -10% (length) Washing procedure: 1X7A+5X5A Total shrinkage FZ/T washing procedure COLORFASTNESS TESTS Color Fastness to Water (FZ/T 73018)-GB/T 5713 /ISO 105 E 01 Small garment -8% (area) Washing procedure: 1X7A+2X5A Trousers, skirt +5% (length), -5% (widthwise) Washing procedure: 3X5A Color change: 3-4 Color stain on wool: 4 Color stain on cotton: 3-4 Color change: 3 Color stain on wool: 3 Color stain on cotton: 3 Color Fastness to Perspiration (FZ/T 73018)-GB/T 3922 /ISO 105 E04 Color change: 3-4 Color stain on wool: 4 Color stain on cotton: 3-4 Cotton can be replaced by another dominant fibre Color change: 3-4 Color stain on wool: 3 Color stain on cotton: 3 Color Fastness to Crocking (Rubbing) (FZ/T 73018)-GB/T 3920 /ISO 105 X12 Color fastness to washing (FZ/T 73018)-GB/T A1S for hand wash, B2S for machine wash/iso 105 C06 Dry: 4 Wet: 3 Color change: 3-4 Color stain on wool: 4 Color stain on cotton: 3-4 Cotton can be replaced by another dominant fibre Dry: 3-4 (dark 3) Wet:

22 TEST DESCRIPTION TEST METHOD Color change: 3 Color stain on wool: 3 Color stain on cotton: 3 Color fastness to light (FZ/T )- GB/T 8427 method 3 / ISO 105 B02 Cotton can be replaced by another dominant fibre High class Grade 4 for dark, Grade 3 for light Grade 3-4 for dark, Grade 3 for light 22

23 Knit Cashmere Goods (Apply to pure cashmere and >30% cashmere blend goods) TEST DESCRIPTION FIBRE CONTENT Fiber content TEST METHOD (FZ/T 73009)-FZ/T 01053, FZ/T 01048, GB/T 2910, 2911,16988/ ISO 1833 Single fiber: 0%; Blend product allow cashmere reduce % (dry content) High class and 1 st class: Max. 3% 2 nd class: Max. 5% PHYSICAL PROPERTIES Bursting Strength (FZ/T GB/T 7742/ ISO rd class: Max. 8% High class, 1 st class, 2 nd class and 3 rd class 225 kpa min for comb Pilling resistance (FZ/T )- GB/T / ISO Coefficient of yarn covering (only for carded plain knit) Variation of tolerance for products weight (%) Comb:4 hr Card: 2 hr (FZ/T )- GB 8689 (FZ/T )- FZ/T kpa min for card : Grade 3-4 min : Grade 3 min 2 nd Class and 3 rd class Grade 2-3 min High class, 1 st class Minimum 1.0 (mm.tex) : -3% comb -5% card : -4% comb -6% card 2 nd Class -5% comb -7% card 3 rd class -7% comb -9% card DIMENSIONAL STABILITY Relaxation Shrinkage (only apply to plain products) FZ/T washing procedure GB X7A and : ±5.0% (Lengthwise and widthwise) COLORFASTNESS TESTS Color Fastness to Water (FZ/T 73009)-GB/T 5713 /ISO 105 E 01 Color change: 4 Color stain on wool: 3-4 Color stain on cotton: 3-4 Color change: 3 Color stain on wool: 3 Color stain on cotton: 3 Color Fastness to Perspiration (FZ/T 73009)-GB/T 3922 /ISO 105 E04 Color change: 3-4 Color stain on wool: 4 Color stain on cotton: 3-4 Cotton can be replaced by another dominant fibre Color change: 3 Color stain on wool: 2-3 Color stain on cotton: 2-3 Cotton can be replaced by another dominant fibre Color Fastness to Crocking (Rubbing) (FZ/T 73009)-GB/T 3920 /ISO 105 X12 Dry: 3-4 Wet: 3 Dry: 3 Wet:

24 TEST DESCRIPTION TEST METHOD Color fastness to washing (FZ/T 73009)-GB/T A1S /ISO 105 C06 Color change: 3-4 Color stain on wool: 4 Color stain on cotton: 3-4 Color change: 3 Color stain on wool: 3 Color stain on cotton: 3 Color fastness to light (FZ/T )- GB/T 8427 method 4 / ISO 105 B02 Cotton can be replaced by another dominant fiber Grade 4 for dark, Grade 3 for light Grade 3-4 for dark, Grade 3 for light 24

25 Knit Silk or Silk Blended Garments TEST DESCRIPTION FIBRE CONTENT Fiber content PHYSICAL PROPERTIES Bursting strength TEST METHOD (FZ/T 43015)-FZ/T 01053, GB/T 2910, 2911/ ISO 1833 (FZ/T 43015)- GB/T section 5.3.1)- the steel ball diameter is 20mm Single fiber: 0%; Blend product allow silk reduce % High class,1 st class and qualified: Max. 5%,, Min 200 N for 80gsm Min 300 N for gsm Min 450 N for 121gsm Dry mass difference per sq. meter (FZ/T 43015)- GB/T section 5.3.2) 6% for 80gsm 5% for gsm 4% for 121gsm, 7% for 80gsm 6% for gsm 5% for 121gsm DIMENSIONAL STABILITY Dimensional stability to washing (FZ/T 43015) GB/T 8628/ISO 3759 GB/T 8629 / ISO 6330 COLORFASTNESS TESTS Color Fastness to Water (FZ/T 43015)-GB/T 5713 /ISO 105 E 01 8% for 80gsm 7% for gsm 6% for 121gsm : -5.0% to +1.0% (Lengthwise) -4.0% to +1.0% (widthwise) : -7.0% to +2.0% (Lengthwise) -6.0% to +2.0% (Widthwise) : -9.0% to +3.0% (Lengthwise) -8.0% to +3.0% (Widthwise) Color change: 4 Color staining: 3 Color change: 3-4 Color staining: 2-3 Color change: 3 Color staining: 2 Color Fastness to Perspiration (FZ/T 43015)-GB/T 3922 /ISO 105 E04 Color change: 4 Color staining: 3 Color change: 3-4 Color staining: 2-3 Color change: 3 Color staining: 2 Color Fastness to Crocking (Rubbing) Color fastness to washing (FZ/T 43015)-GB/T 3920 /ISO 105 X12 (FZ/T 43015)-GB/T /ISO 105 C10 Dry: 3-4 Wet: 3 Color change: 4 Color staining: 3 Dry: 3 Wet: 2-3 Color change: 3-4 Color staining: 2-3 : Dry: 2-3 Wet: 2 Color change: 3 Color staining: 2 Color fastness to light (FZ/T 43015)-GB/T 8427 /ISO 105 B02 High class Grade st class Grade 3 Grade

26 Knit Sportswear TEST DESCRIPTION FIBRE CONTENT Fiber Content PHYSICAL PROPERTIES Bursting Strength Seam Bursting Strength (backrise seam) Pilling Resistance DIMENSIONAL STABILITY Resistance to Torque (Spirality) Dimensional Stability to Washing TEST METHOD (GB/T 22853)-FZ/T 01053,GB/T 2910, GB/T 2911, FZ/T 01026, FZ/T / ISO 1833 (GB/T 22853)-GB/T (GB/T 22853)-FZ/T (GB/T 22853)-GB/T (GB/T 22853)-GB/T item 5.4.5/ISO (GB/T 22853)-GB/T 8629/ ISO 6330 COLORFASTNESS TESTS Color Fastness to Water (GB/T 22853)-GB/T 5713 /ISO 105 E 01 Color Fastness to Perspiration Color Fastness to Crocking (Rubbing) Color Fastness to Washing (GB/T 22853)-GB/T 3922 /ISO 105 E04 (GB/T 22853)-GB/T 3920 /ISO 105 X12 (GB/T 22853)-GB/T 3921 A (1)/ISO 105 C10 Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30%, and : Min 180 N for top Min 220 for trousers, and : Min 140 N : Grade 3.5 min : 4.0% for top 1.5% for trousers Grade 3.0 min : 5.0% for top 3.0% for trousers : -4.0% to +2.0% (Lengthwise and widthwise) : -5.5% to +3.0% (Lengthwise and widthwise) : -6.5% to +3.0% (Lengthwise and widthwise) Color change: 4 Color staining: 4 Color change: 4 Color staining: 4 Dry: 4 Wet: 3 (Printing) Dry: 3-4 Wet: 3 Color change: 4 Color stain: 4 Color change: 3-4 Color staining:3-4 Color change: 3-4 Color staining:3-4 Dry: 3-4 Wet: 2-3 (dark color:2) (Printing) Dry: 3 Wet: 2-3 Color change: 4 Color stain: 3-4 : Grade 2.5 min Class: 8.0% for top 3.5% for trousers Color change: 3 Color staining:3 Color change: 3 Color staining:3 Dry: 3 Wet: 2-3 (dark color:2) (Printing) Dry: 3 Wet: 2-3 (dark color: 2) Color change: 3-4 Color stain: 3 Dye Transfer after Washing (GB/T 22853)-GB/T Appendix A (ISO 105 C10) Color Fastness to Light (GB/T 22853)-GB/T 8427 method 3 / ISO 105 B02 (Printing) Color change: 4 Color stain: 3-4 Cross staining: 4-5 Grade 4 (Printing) Color change: 3-4 Color stain: 3 & Cross staining: 4 Grade 4 (Grade 3 for light) (Printing) Color change: 3 Color stain: 3 Grade 3 Color Fastness to Light and perspiration (GB/T 22853)-GB/T14576 B/ISO 105 B07 High class Grade st class Grade 3 Grade

27 2.1.2 Woven Trench coats TEST TEST METHOD DESCRIPTION FIBRE CONTENT Fiber Content (FZ/T 81010)-FZ/T 01053, GB/T 2910, / ISO 1833 Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30% PHYSICAL PROPERTIES Peeling strength (FZ/T 81010)-FZ/T Min: 6N/(2.5cm 10cm) Pilling Resistance (FZ/T 81010)-GB/T High class Grade 4 min for smooth surface Grade 3-4 min for pile, 1 st class/qualified Grade 3-4 min for smooth surface Grade 3 min for pile Seam Slippage (FZ/T 81010)-FZ/T Appendix A /ISO Fabric < 50 gsm Shell 0.8 cm at 100 N Lining 0.8 cm at 70N Other fabric Shell 0.6 cm at 100 N Lining 0.6cm at 70N Water Repellency Tearing Strength DIMENSIONAL STABILITY Dimensional Stability to Washing Dimensional Stability to Drycleaning Assessment of Crease After Drycleaning (FZ/T 81010)-GB/T 4745/ISO 4920 (FZ/T 81010)-GB/T /ISO GB/T 8630/ISO 5077 FZ/T /ISO 3175 Visual evaluation FZ/T item 10 /ISO 7768 Silk: Shell 0.6 cm at 67 N for > 52gsm fabric, 0.6 cm at 45 N for 52gsm fabric and > 67 gsm satin 4 10 N minimum for general 7 N minimum for silk and cotton item < 140 gsm High class -1.5% to +1.5% length -1.0% to +1.0% chest 1 st class -2.5% to +1.0% length -2.0% to +1.0% chest High class, 1 st class, qualified -1.0% to +1.0% length -0.8% to +0.8% chest High class st class % to +1.0% length -2.5% to +1.0% chest 3.0 COLORFASTNESS TESTS Color Fastness to Water (FZ/T 81010)-GB/T 5713 /ISO 105 E01 Color Fastness to Perspiration Color Fastness to Crocking (Rubbing) (FZ/T 81010)-GB/T 3922 /ISO 105 E04 (FZ/T 81010)-GB/T 3920 /ISO 105 X 12 High class Color change: 4 Color staining:4 High class Color change: 4 Color staining:4 Dry: 4 Wet:: st class Color change: 3-4 Color staining:3-4 1 st class Color change: 3-4 Color staining:3-4 Dry: 3-4 Wet:: 3 Color change: 3 Color staining:3 Color change: 3 Color staining:3 Dry: 3 Wet: 3 (dark 2-3) 27

28 TEST DESCRIPTION Color Fastness to Washing Color Fastness to Drycleaning Color fastness to hot pressing TEST METHOD (FZ/T 81010)-GB/T , /ISO 105 C10 (FZ/T 81010)-GB/T 5711 /ISO 105 D01 GB/T 6152/ISO 105 X11 Color Fastness to Light (FZ/T 81010)-GB/T 8427 Method 3 /ISO 105 B02 High class Color change: 4 Color staining:4 High class Color change: 4-5 Color staining:4-5 High class Color change: 4 High class Grade 4 1 st class Color change: 3-4 Color staining:3-4 1 st class Color change: 4 Color staining:4 1 st class Color change: st class Grade 3-4 Color change: 3 Color staining:3 Color change: 3-4 Color staining:3-4 Pass Color change: 3 Grade 3 28

29 Woven Casual Wear (Apply to casual wear made up of cotton, linen, silk, synthetic fiber, and its blends fabric) TEST DESCRIPTION FIBRE CONTENT Fiber Content TEST METHOD (FZ/T 81007)-FZ/T 01053,GB/T 2910, GB/T 2911, FZ/T / ISO 1833 Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30% PHYSICAL PROPERTIES Peeling strength (FZ/T 81007)-FZ/T Min: 6N/(2.5cm 10cm) Pilling Resistance (FZ/T 81007)-GB/T High class and 1 st class Grade 4 min Grade 3 min Seam Slippage (FZ/T 81007)-FZ/T Appendix A /ISO High class Shell 0.5 cm at 100 N Lining High class 0.5 cm at 70 N Seam Strength (FZ/T 81007)-GB/T Shell 140 N for back rise seam Lining 80 N for back rise seam DIMENSIONAL STABILITY Dimensional Stability to Washing Dimensional Stability to Drycleaning (FZ/T 81007)-GB/T 8629 /ISO 6330 (FZ/T 81007)-FZ/T /ISO 3175 COLORFASTNESS TESTS Color Fastness to Water (FZ/T 81007)-GB/T 5713 /ISO 105 E01 Color Fastness to Perspiration (FZ/T 81007)-GB/T 3922 /ISO 105 E04 Neck width -1.0% Chest -1.5% length -1.5% waist -1.0% trousers length -1.5% Neck width: -1.5% Chest: -2.0% Length: -2.0% Waist: -1.5% Trousers length: -2.0% 1 st class & qualified Shell 0.6 cm at 100 N Lining 1 st class & qualified 0.6 cm at 70 N (silk products and weight <50g/m2 fabric refer to GB/T 18132) Neck width -1.0% Chest -2.0% length -2.5% waist -1.5% trousers length -2.5% Mandatory in China GB Color change 3 Color staining 3 Shell High class Color change: 4 Color stain: 4 Shell 1 st class Color change: 3-4 Color stain: 3-4 Neck width -1.5% Chest -2.5% length -3.5% waist -2.0% trousers length -3.5% Shell Color change: 3 Color stain: 3 Color Fastness to Crocking (Rubbing) (FZ/T 81007)-GB/T 3920 /ISO 105 X 12 Shell Dry: 4 Wet:: 4 Shell Dry: 3-4 Wet:: 3-4 Shell Dry: 3 Wet:: 3 Color Fastness to (FZ/T 81007)-GB/T Shell Lining Dry: 3-4 Wet::

30 TEST DESCRIPTION TEST METHOD Washing or /ISO 105 C10 High class Color change: 4 Color stain: 4 1 st class Color change: 3-4 Color stain: 3-4 Color change: 3 Color stain: 3 Lining: Staining: 3 Color Fastness to Drycleaning (FZ/T 81007)-GB/T 5711 /ISO 105 D01 Color Fastness to Light (FZ/T 81007)-GB/T 8427 Method 3 /ISO 105 B02 Worldwide) Embroidery Staining: 3 High class Color change: 4-5 Color stain: st class Color change: 4 Color stain: 4 Color change: 3-4 Color stain: 3-4 High class Grade 4 1 st class Grade 3-4 Grade 3 30

31 Jackets TEST TEST METHOD DESCRIPTION FIBRE CONTENT Fiber Content (FZ/T 81008)-FZ/T 01053, FZ/T01057, GB/T 2910, GB/T 2911, / ISO 1833 Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30% PHYSICAL PROPERTIES Peeling strength (FZ/T 81008)-FZ/T Min: 6N/(2.5cm 10cm) Pilling Resistance (FZ/T 81008)-GB/T High class Grade 4 min 1 st class Grade 3-4 min Grade 3 min Seam Slippage DIMENSIONAL STABILITY Dimensional Stability to Washing Dimensional Stability to Drycleaning Smoothness appearance of seam after Washing (report 1 st to 5 th wash) for washable item Assessment of Crease After Washing for washable item (FZ/T 81008)-FZ/T81008 Appendix A /ISO (FZ/T 81008)-GB/T 8629/ISO 6330 (FZ/T 81008)-FZ/T /ISO 3175 (FZ/T 81008)-GB/T 13771/ISO 7770 (FZ/T 81008)-GB/T 13769/ISO 7768 COLORFASTNESS TESTS Color Fastness to Water (FZ/T 81008)-GB/T 5713 /ISO 105 E01 Color Fastness to Perspiration (FZ/T 81008)-GB/T 3922 /ISO 105 E04 High class Shell 0.5 cm at 100 N 1 st class and qualified Shell 0.6 cm at 100 N Lining High class 0.5 cm at 70 N 1 st class & qualified 0.6 cm at 70 N High class Neck width: -1.0% Chest: -1.5% Length: -1.5% 1 st class Neck width: -1.0% Chest: -2.0% Length: -2.5% Neck width: -1.5% Chest: -2.5% Length: -3.5% Neck width: -1.5% Chest: -2.0% Length: -2.0% High class st class and qualified 3.0 High class st class and qualified Not required for this test Shell High class, 1 st class, qualified Color change: 3 Color stain: 3 Shell: Acidic & Alkaline High class, 1 st class, qualified Color change: 3 Color stain: 3 Color Fastness to (FZ/T 81008)-GB/T 3920 Shell 31

32 TEST DESCRIPTION TEST METHOD Crocking (Rubbing) /ISO 105 X 12 Dry: 4 Wet:: 4 Dry: 3-4 Wet:: 3-4(3 for dark) Dry: 3 Wet:: 3 (2-3 for dark) Color Fastness to Washing Color Fastness to Drycleaning (FZ/T 81008)-GB/T , /ISO 105 C10 (FZ/T 81008)-GB/T 5711 /ISO 105 D01 Color Fastness to Light (FZ/T 81008)-GB/T 8427 Method 3 /ISO 105 B02 Shell High class, Color change: 4 Color stain: 4 Shell High class, Color change: 4-5 Color stain: 4-5 Shell High class Grade 4 1 st class, Color change: 3-4 Color stain: 3-4 Shell 1 st class, Color change: 4 Color stain: 4 Shell 1 st class Grade 3-4 Lining Dry: 3-4 Wet:: 3-4 Color change: 3 Color stain: 3 Lining Color stain: 3 Shell Color change: 3-4 Color stain: 3-4 Shell Grade 3 32

33 Jeanswear (Apply to normal / coloured jeanswear made up of pure cotton, cotton blends denim) TEST DESCRIPTION FIBRE CONTENT Fiber Content TEST METHOD (FZ/T 81006)-FZ/T 01053, FZ/T01057, GB/T 2910, GB/T 2911, FZ/T 01026, FZ/T appendix B / ISO 1833 PHYSICAL PROPERTIES Peeling strength (FZ/T 81006)- FZ/T Seam Slippage (FZ/T 81006)-FZ/T Appendix C /ISO Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30% Min: 6N/(2.5cm 10cm) 0.5 cm at 100 N for fabric weight < 339 gsm 0.5 cm at 150 N for fabric weight 339 gsm 1 st class & : 0.6 cm at 100 N for fabric weight < 339 gsm 0.6 cm at 150 N for fabric weight 339 gsm Seam Strength Tensile Strength Tearing Strength (FZ/T 81006)-GB/T (FZ/T 81006)-GB/T /ISO (FZ/T 81006)-GB/T /ISO Lining 0.5cm at 70N 1 st class & : 0.6 cm at 70N Fabric weight < 339 gsm 140 N for back rise seam Fabric weight 339 gsm 180 N for back rise seam Fabric weight 339 gsm Before wash Warp: 450 N minimum Weft: 300 N minimum After wash Warp: 320 N minimum Weft: 200 N minimum Fabric weight > 245gsm to < 339 gsm Before wash Warp: 300 N minimum Weft: 250 N minimum After wash Warp: 300 N minimum Weft: 150 N minimum Fabric weight 245 gsm (for non denim product) Before wash Warp: 200 N minimum Weft: 150 N minimum After wash Warp: 150 N minimum Weft: 150 N minimum Fabric weight 339 gsm Warp: 25 N minimum Weft: 18 N minimum Fabric weight > 245gsm to < 339 gsm Warp: 23 N minimum 33

34 TEST DESCRIPTION TEST METHOD Weft: 18 N minimum Abrasion Resistance (FZ/T 81006)-FZ/T /ISO DIMENSIONAL STABILITY Dimensional Stability to Washing (FZ/T 81006)-GB/T 8629/ISO 6330 Torque after wash (FZ/T 81006)-FZ/T appendix B Torque Displacement after wash (FZ/T 81006)-FZ/T appendix B COLORFASTNESS TESTS Color Fastness to Water (FZ/T 81006)-GB/T 5713 /ISO 105 E01 Color Fastness to Perspiration (FZ/T 81006)-GB/T 3922 /ISO 105 E04 Fabric weight 245 gsm (for non denim pant) Warp: 15 N minimum Weft: 11 N minimum cycles for fabrics weighing up to 339 gsm cycles for fabrics weighing > 339 gsm Neck width -1.5% to +1.0% (BW) -1.5% to +1.0% (AW) Chest -2.0% to +1.0% (BW) -1.5% to +1.0% (AW) length -2.0% to +1.0% (BW) -1.5% to +1.0% (AW) waist -1.5% to +1.0% (BW) -1.5% to +1.0% (AW) Dress length -2.0% to +1.0% (BW) -1.5% to +1.0% (AW) High class 2.0 cm 1 st class & qualified 3.0 cm High class 1.5 cm 1 st class & qualified 2.5 cm Neck width -2.0% to +1.0% (BW) -2.0% to +1.5% (AW) Chest -2.5% to +1.0% (BW) -2.5% to +1.5% (AW) length -2.5% to +1.0% (BW) -2.5% to +1.5% (AW) waist -2.0% to +1.0% (BW) -2.5% to +1.5% (AW) Dress length -2.5% to +1.0% (BW) -2.5% to +1.5% (AW) With & Without Garment Wash Color change: 4 Color stain: 3-4 With & Without Garment Wash Color change: 3-4 Color stain: 3 (for baby 3-4) Without Garment Wash Color change: 3(for baby 3-4) Color stain: 3 (for baby 3-4) With Garment Wash Color change: 3-4 Color staining: 3 (for baby 3-4) With & Without Garment Wash Color change: 4 Neck width -2.5% to +1.0% (BW) -2.0% to +1.5% (AW) Chest -3.0% to +1.5% (BW) -2.5% to +1.5% (AW) length -3.0% to +1.5% (BW) -2.5% to +1.5% (AW) waist -2.5% to +1.5% (BW) -2.5% to +1.5% (AW) Dress length -3.0% to +1.5% (BW) -2.5% to +1.5% (AW) 34

35 TEST DESCRIPTION Color fastness to saliva (for baby product) Color Fastness to Crocking (Rubbing) Color Fastness to Washing TEST METHOD (FZ/T 81006)-GB/T (FZ/T 81006)-GB/T 3920 /ISO 105 X 12 (FZ/T 81006)-GB/T /ISO 105 C10 Color stain: 3-4 With & Without Garment Wash Color change: 3-4 Color stain: 3 (for baby 3-4) Without garment Wash Color change: 3 (for baby 3-4) Color stain: 3 (for baby 3-4) With Garment Wash Color change: 3-4 Color staining: 3 (for baby 3-4) With & Without Garment Wash High class Color change: 4-5 Color stain: 4 1 st class & qualified Color change: 4 Color stain: 4 With & Without Garment Wash Dry: 3-4 (for baby 4) and With & Without Garment Wash Dry: 3 (for baby 4) High class With & Without Garment Wash Color change: 4 Color stain: 3 1 st class With & Without Garment Wash Color Fastness to Light (FZ/T 81006)-GB/T 8427 Method 3 /ISO 105 B02 Color change: 3-4 Color stain: 2-3 Without Garment Wash Color change: 3 Color stain: 2-3 With Garment Wash Color change: 3-4 Color stain: 2-3 Without Garment Wash High class Grade 4 1 st class and Grade 3 With Garment Wash High class Grade 4 1 st class and Grade

36 Shirts and Blouses TEST DESCRIPTION FIBRE CONTENT Fiber Content TEST METHOD (GB/T 2660)-FZ/T 01053,GB/T 2910, GB/T 2911, FZ/T 01026, FZ/T 01095, FZ/T 30003/ ISO 1833 PHYSICAL PROPERTIES Seam Slippage (GB/T 2660)-GB/T 2660 Appendix B /ISO Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30% Shell 0.6 cm at 100 N Lining 0.6 cm at 70 N Silk : GB/T Appendix A/ISO Shell 0.6 cm at 67 N for > 52gsm fabric, 0.6 cm at 45 N for 52gsm fabric Lining 0.6 cm at 70 N Tearing Strength GB/T /ISO N minimum for general 7 N minimum for silk and cotton item < 140 gsm DIMENSIONAL STABILITY Dimensional Stability to Washing (GB/T 2660)-GB/T 8630/ISO 5077 High class -1.0% neck -1.5% check -2.0% length 1 st class --1.5% neck -2.0% check -2.5% length Smoothness Appearance of seam before Washing Smoothness Appearance of seam after Washing (report 1 st and 5 th wash) Dimensional Stability to Drycleaning Visual evaluation GB/T 2660 item 4.4.2/ ISO 7770 Visual evaluation GB/T 2660 item 4.4.2/ISO 7770 (GB/T 2660)-FZ/T /ISO 3175 COLORFASTNESS TESTS Color Fastness to Water (GB/T 2660)-GB/T 5713 /ISO 105 E01 Color Fastness to Perspiration (GB/T 2660)-GB/T 3922 /ISO 105 E04-2.0% neck -2.5% check -3.0% length Collar, pocket, cuff,, 4.5 Side seam, Hem line 4.0 High class Collar, pocket, cuff, > 4.0 Side seam, hem line, > st class Collar, cuff, > 4.0 Side seam, pocket, hem line, > 3.5 Collar, pocket, cuff, Side seam, hem line, > 3.0 High class -1.0% neck -1.5% check -2.0% length High class Color change: 4 Color staining:4 High class Color change: 4 Color staining:4 1 st class --1.5% neck -2.0% check -2.5% length 1 st class and Color change: 3 Color staining:3 1 st class and Color change: 3 Color staining:3-2.0% neck -2.5% check -3.0% length Color Fastness to Crocking (Rubbing) (GB/T 2660)-GB/T 3920 /ISO 105 X 12 Dry: 4 Wet:: 4 Dry: 3-4 Wet:: 3-4 Dry: 3 Wet:: 3 36

37 TEST DESCRIPTION TEST METHOD Color Fastness to Washing Color Fastness to Drycleaning (GB/T 2660)-GB/T or /ISO 105 C10 (GB/T 2660)-GB/T 5711 /ISO 105 D01 High class Color change: 4 Color staining:4 High class Color change: 4-5 Color staining:4-5 1 st class Color change: 3-4 Color staining:3-4 1 st class Color change: 4 Color staining:4 Color change: 3 Color staining:3 Color change: 3-4 Color staining:3-4 Color Fastness to Light (GB/T 2660)-GB/T 8427 Method 3 /ISO 105 B02 High class Grade 4 1 st class Grade 3-4 Grade 3 37

38 Skirts and Skirted suit (Apply to Skirts and skirted suit made up of cotton, linen, silk, synthetic fiber, and its blends fabric) TEST DESCRIPTION TEST METHOD FIBRE CONTENT Fiber Content (FZ/T 81004)-FZ/T 01053, FZ/T01057, GB/T 2910, GB/T 2911/ ISO 1833 PHYSICAL PROPERTIES Peeling strength (FZ/T 81004)- FZ/T Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30% Min: 6N/(2.5cm 10cm) Pilling Resistance (FZ/T 81004)-GB/T Seam Slippage (FZ/T 81004)-FZ/T Appendix A /ISO DIMENSIONAL STABILITY Dimensional Stability to Washing Dimensional Stability to Drycleaning Silk : GB/T Appendix A/ISO (FZ/T 81004)-GB/T 8629/ISO 6330 GB/T8630/ISO 5077 (FZ/T 81004)-FZ/T /ISO 3175 COLORFASTNESS TESTS Color Fastness to Water (FZ/T 81004)-GB/T 5713 /ISO 105 E01 & 1 st class: Grade 4 min : Grade 3 min : Shell 0.5 cm at 100 N Lining 0.5 cm at 70N 1st class & qualified: Shell 0.6 cm at 100 N Lining 0.6 cm at 70N Shell 0.6 cm at 67 N for > 52gsm fabric, 0.6 cm at 45 N for 52gsm fabric or >67gsm satin fabric Lining 0.6 cm at 70 N Neck width -1.0% Chest -1.5% length -1.5% waist -1.0% Dress length -1.5% Neck width -1.5% Chest -2.0% length -2.0% waist -1.5% Dress length -2.0% Neck width -1.0% Chest -2.0% length -2.5% waist -1.5% Dress length -2.5% Mandatory in China GB Color change 3 Color staining 3 Neck width -1.5% Chest -2.5% length -3.5% waist -2.0% Dress length -3.5% Color Fastness to Perspiration (FZ/T 81004)-GB/T 3922 /ISO 105 E04 Shell Color change: 4 Color stain: 4 Shell Color change: 3-4 Color stain: 3-4 Shell Color change: 3 Color stain: 3 38

39 TEST DESCRIPTION Color Fastness to Crocking (Rubbing) Color Fastness to Washing Color Fastness to Drycleaning TEST METHOD (FZ/T 81004)-GB/T 3920 /ISO 105 X 12 (FZ/T 81004)-GB/T , /ISO 105 C10 (FZ/T 81004)-GB/T 5711 /ISO 105 D01 Shell Dry: 4 Wet: 4 Dry: 3-4 Wet: 3-4 Dry: 3 Wet: 3 Lining Dry: 3-4 Shell Color change: 4 Color stain: 4 Color change: 3-4 Color stain: 3-4 Color change: 3 Color stain: 3 lining: Color stain: 3 Embroidery: Color stain:3 Shell Color change: 4-5 Color stain: 4-5 Color change: 4 Color stain: 4 Color Fastness to Light (FZ/T 81004)-GB/T 8427 Method 3 /ISO 105 B02 Color change: 3-4 Color stain: 3-4 Shell High class Grade 4 1 st class Grade 3-4 Grade 3 39

40 Trousers/Skirt (Apply to formal trousers / skirt made up of wool, its blends, wool like woven fabrics) TEST TEST METHOD DESCRIPTION FIBRE CONTENT Fiber Content (GB/T 2666)-FZ/T 01053, FZ/T 01057, GB/T 2910, GB/T 2911, FZ/T 01026, GB/T 16988, FZ/T01048 / ISO 1833 Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30% PHYSICAL PROPERTIES Pilling Resistance (GB/T 2666)-GB/T High class Grade 4 min for combed(smooth face) Grade 3-4 min for combed (pile face) and carded 1 st class & qualified Grade 3-4 min for combed(smooth face) Seam Slippage (GB/T 2666)-GB/T 2666 Appendix B /ISO Grade 3 min for combed (pile face) and carded Shell 0.6 cm at 100 N Lining 0.6 cm at 70 N Seam Strength (GB/T 2666)-GB/T Shell 140 N for back rise seam Lining 80 N for back rise seam Tearing Strength (GB/T 2666)-GB/T /ISO All classes 10 N minimum DIMENSIONAL STABILITY Dimensional Stability to Washing Dimensional Stability to Drycleaning Spirality / Skewness after Washing Spirality / Skewness after Drycleaning (GB/T 2666)-GB/T 8630/ISO 5077 (GB/T 2666)-FZ/T /ISO 3175 (GB/T 2666)-GB/T 2666 Appendix A /ISO (GB/T 2666)-GB/T 2666 Appendix A /ISO COLORFASTNESS TESTS Color Fastness to Water (GB/T 2666)-GB/T 5713 /ISO 105 E01 All class -1.5 to +1.5% lengthwise, -1.2 to +1.0 for waist All class -1.0% to +1.0% lengthwise -0.8% to +0.8% for waist High class 2.0% 1 st class and qualified 4.0% High class 1.5% 1 st class and qualified 3.0% Shell High class Color change: 4 Color staining:4 1 st class Color change: 4 Color staining:3-4 Color change: 3-4 Color staining:3 Lining High class Color change: 4 Color staining:4 1 st class Color change: 3-4 Color staining:3-4 Color change: 3 Color staining:3 40

41 TEST DESCRIPTION Color Fastness to Perspiration Color Fastness to Crocking (Rubbing) TEST METHOD (GB/T 2666)-GB/T 3922 /ISO 105 E04 (GB/T 2666)-GB/T 3920 /ISO 105 X 12 Shell High class Color change: 4 Color staining:4 Lining High class Color change: 4 Color staining:4 shell Dry: 4 Wet:: 3-4 Shell 1 st class Color change: 3-4 Color staining:3-4 Lining 1 st class and Color change: 3 Color staining:3 shell Dry: 3-4 Wet:: 3 Shell Color change: 3 Color staining:3 shell Dry: 3 Wet: 2-3 Color Fastness to Washing (GB/T 2666)-GB/T 3921 A (1) /ISO 105 C10 Lining Dry: 4 Shell High class Color change: 4 Color staining:4 Lining Dry: 3-4 Shell 1 st class Color change: 3-4 Color staining:3-4 Lining Dry: 3 Shell Color change: 3-4 Color staining:3 Color Fastness to Drycleaning (GB/T 2666)-GB/T 5711 /ISO 105 D01 Color Fastness to Light (GB/T 2666)-GB/T 8427 Method 3 /ISO 105 B02 Lining High class Color staining:4 Shell High class Color change: 4-5 Color staining:4-5 Lining High class & 1 st class Color staining:4 Shell High class Grade 4 (dark, light) Lining 1 st class Color staining:3-4 1 st class Color change: 4 staining:4 Shell 1 st class Grade 3 light, Grade 4 dark Lining Color staining:3 Decoration and embroidery: Color stain: 3-4 Color change: 3-4 Color staining:3-4 Lining Color staining:3-4 Decoration and embroidery: Color stain: 3-4 Shell Grade 3 (dark, light) 41

42 Women s suits and coats (Apply to Women's suits and coats made up of wool, its blends, wool like woven fabrics) TEST TEST METHOD DESCRIPTION FIBRE CONTENT Fiber Content (GB/T 2665)-FZ/T 01053, FZ/T01057, GB/T 2910, GB/T 2911, FZ/T 01026, GB/T16988, FZ/T01048 / ISO 1833 Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30% PHYSICAL PROPERTIES Peeling strength (GB/T 2665)-FZ/T Min: 6N/(2.5cm 10cm) Pilling Resistance (GB/T 2665)-GB/T High class Grade 4 min for combed(smooth face) Grade 3-4 min for combed (pile face) and carded 1 st class and qualified Grade 3-4 min for combed(smooth face) Seam Slippage (GB/T 2665)-GB/T 2665 Appendix A /ISO Tearing Strength (GB/T 2665)-GB/T /ISO DIMENSIONAL STABILITY Dimensional Stability to Washing Dimensional Stability to Drycleaning Assessment of Crease After Drycleaning (GB/T 2665)-GB/T 8630/ISO 5077 FZ/T /ISO 3175 GB/T 2665 section (section men s suit crinkle reference photo)/iso 7768 COLORFASTNESS TESTS Color Fastness to Water (GB/T 2665)-GB/T 5713 /ISO 105 E01 Grade 3 min for combed (pile face) and carded Shell 0.6 cm at 100 N Lining 0.6cm at 70N High class, 1 st class, qualified 10 N minimum High class, 1 st class, and qualified -1.5% to +1.5% length -1.0% to +1.0% chest High class, 1 st class, and qualified -1.0% to +1.0% length -0.8% to +0.8% chest High class >4 Shell High class Color change: 4 Color staining:4 1 st class 4 Shell 1 st class Color change: 4 Color staining:3-4 qualified 3 Shell Color change: 3-4 Color staining:3 Color Fastness to Perspiration Color Fastness to Crocking (Rubbing) (GB/T 2665)-GB/T 3922 /ISO 105 E04 (GB/T 2665)-GB/T 3920 /ISO 105 X 12 Lining High class Color staining:4 Lining 1 st class Color staining:3-4 Mandatory in China in GB Acidic & Alkaline Color change 3 Color staining 3 Shell Dry: 4 Wet:: 3-4 Shell Dry: 3-4 Wet:: 3 Lining Color staining:3 Shell Dry: 3 Wet:: 2-3 Color Fastness to Washing (GB/T 2665)-GB/T 3921 A (1)/ISO 105 C10 Color Fastness to (GB/T 2665)-GB/T 5711 Shell Lining High Class Dry: 4 Shell High class Color change: 4 Color staining:4 Lining High class Color staining:4 Lining Dry: 3-4 Shell 1 st class Color change: 3-4 Color staining:3-4 Lining 1 st class Color staining:3-4 Lining Dry: 3 Shell Color change:3-4 Color staining:3 Lining Color staining:3 All classes Decoration and embroidery: Color stain:

43 TEST DESCRIPTION TEST METHOD Drycleaning /ISO 105 D01 High class Color change: 4-5 Color staining:4-5 1 st class Color change: 4 Color staining:4 Color change: 3-4 Color staining:3-4 lining High class & 1 st class Color staining:4 Color staining:3-4 Color Fastness to Light (GB/T 2665)-GB/T 8427 Method 3 /ISO 105 B02 All classes Decoration and embroidery: Color stain: 3-4 High class Grade 4 (dark, light) 1 st class Grade 3 light, Grade 4 dark Grade 3 (dark, light) 43

44 Woven Silk Garments TEST TEST METHOD DESCRIPTION FIBRE CONTENT Fiber content (GB/T 18132)-FZ/T 01053, FZ/T01057, GB/T 2910, GB/T 2911, FZ/T 01026, FZ/T 01095/ ISO 1833 PHYSICAL PROPERTIES Seam Slippage (GB/T 18132)-GB/T Appendix A /ISO Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30% Shell 0.6 cm at 67 N for > 52gsm fabric, 0.6 cm at 45 N for 52gsm fabric or >67gsm satin fabric Lining 0.6 cm at 70 N Seam Strength (GB/T 18132)-GB/T Shell 140 N for back rise seam Lining 80 N for back rise seam Tearing strength DIMENSIONAL STABILITY Dimensional stability to washing (GB/T 18132)-GB/T /ISO (GB/T 18132)-GB/T 8629/ISO 6330 GB/T8630/ISO 5077 Shell and lining 7 N minimum Neck width -1.0% Chest -1.5% length -1.5% waist -1.0% Trouser/Dress length -1.5% Neck width -1.0% Chest -2.0% length -2.5% waist -1.5% Trouser/Dress length -2.5% Neck width -1.5% Chest -2.5% length -3.5% waist -2.0% Trouser/Dress length -3.5% Dimensional stability to drycleaning Appearance after laundering (GB/T 18132)-GB/T /ISO 3175 GB/T section Visual evaluation (1 wash) COLORFASTNESS TESTS Color Fastness to Water (GB/T 18132)-GB/T 5713 /ISO 105 E01 Neck width -1.0% Chest -1.5% length -1.0% waist -1.0% Trouser /Dress length -1.5% Acceptable Appearance Neck width -1.0% Chest -1.5% length -2.0% waist -1.5% Trouser/Dress length -2.0% Shell Color change: 4 Color stain: 4, Color change: 3 Color stain: 3 lining Color change: 3 (3-4) for infant Neck width -1.5% Chest -2.0% length -2.5% waist -2.0% Trouser/Dress length -3.0% 44

45 Color Fastness to Perspiration Color Fastness to Crocking (Rubbing) Color fastness to washing Color fastness to drycleaning (GB/T 18132)-GB/T 3922 /ISO 105 E04 (GB/T 18132)-GB/T 3920 /ISO 105 X 12 (GB//T 18132)-GB/T 3921/ISO 105 C10 (GB/T 18132)-GB/T 5711 /ISO 105 D01 Shell Color change: 4 Color stain: 4, Color change: 3 Color stain: 3 Lining Color change: 3 (3-4) for infant Shell Dry: 4 Wet: 4 Dry: 3-4 Wet: 3-4 Dry: 3 Wet: 3 Lining Dry: 3 (4) for infant Shell Color change: 4 Color stain: 3-4 Color change: 3-4 Color stain: 3 Color change: 3-4 Color stain: 2-3 lining: Color stain: 2-3 Embroidery, decoration: Color stain:3-4 Shell Color change: 4-5 Color stain: 4 Color change: 4 Color stain: 3-4 Color change: 3-4 Color stain: 3 Embroidery, decoration: Color stain:3-4 Color fastness to saliva (for infant only) GB/T18886 Color fastness to light (FZ/T 81004)-GB/T 8427 Method 3 /ISO 105 B02 Shell, 1 st class and qualified Color change: 4 Color stain: 4 Shell High class Grade 4 Shell 1 st class Grade 3-4 Shell Grade 3 45

46 Woven Infant s wear (Apply to age 24 months) TEST TEST METHOD DESCRIPTION FIBRE CONTENT Fiber content (FZ/T 81014)-FZ/T 01053, FZ/T01057, GB/T 2910, GB/T 2911, FZ/T 01026, FZ/T 01095, FZ/T 30003/ ISO 1833 PHYSICAL PROPERTIES Accessory pull strength Seam strength of cord and drawstring DIMENSIONAL STABILITY Dimensional stability to washing FZ/T Annex A (EN71-1) (FZ/T 81014)-GB/T (cut position as section ) (FZ/T 81014)-GB/T 8629/ISO 6330 GB/T8630/ISO 5077 COLORFASTNESS TESTS Color Fastness to Water (FZ/T 81014)-GB/T 5713 /ISO 105 E01 Color Fastness to Perspiration (FZ/T 81014)-GB/T 3922 /ISO 105 E04 Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30% Not detach, 1 st class, qualified 70N Chest, body length, trouser/dress length -2.5% Color change: 4 Color stain: 4, Color change: 3-4 Color stain: 3-4 Color change: 4 Color stain: 4, Color change: 3-4 Color stain: 3-4 Chest, body length, trouser/dress length -3.0% Chest, body length, trouser/dress length -3.5% Color Fastness to Crocking (Rubbing) Color fastness to washing (fz/t81014)-gb/t 3920 /ISO 105 X 12 (FZ//T 81014)-GB/T or /ISO 105 C10 Dry: 4 Wet: 4 Dry: 4 Wet: 3-4 Dry: 4 Wet: 3 Color change: 4 Color stain: 4 Color change: 3-4 Color stain: 3-4 Color change: 3 Color stain: 3 Color fastness to saliva GB/T18886, 1 st class and qualified Color change: 4 Color stain: 4 46

47 2.1.3 Intimate Cotton Knit Underwear (Apply to cotton or blends knitted underwear). TEST TEST METHOD DESCRIPTION FIBRE CONTENT Fiber Content (GB/T 8878)-FZ/T 01053,GB/T 2910, GB/T 2911, FZ/T 01057, FZ/T 01095, FZ/T 01026/ ISO 1833 PHYSICAL PROPERTIES Bursting Strength (GB/T 8878)-GB/T 19976, the steel ball diameter is 38mm Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30%,, Min 150 N for single, rib, fuzz Min 220 N for double fabric DIMENSIONAL STABILITY Dimensional Stability to Washing (GB/T 8878)-GB/T8629 / ISO 6330 (not applicable for shorts) COLORFASTNESS TESTS Color Fastness to Water (GB/T 8878)-GB/T 5713 /ISO 105 E 01 Fuzz fabric : -7.0% (Lengthwise) -4.0% to +3.0% (widthwise) -8.0% (Lengthwise) -5.0% to +3.0% (widthwise) -9.0% (Lengthwise) -6.0% to +3.0% (widthwise) Double fabric : -5.0% (Lengthwise) -5.0% to 0.0% (widthwise) -7.0% (Lengthwise) -8.0% to +2.0% (widthwise) -9.0% (Lengthwise) -10.0% to +2.0% (widthwise) Single : -5.0% (Lengthwise) -5.0% to +0.0% (widthwise) -5.0% (Lengthwise) -6.5% to +2.0% (widthwise) -6.0% (Lengthwise) -8.0% to +2.0% (widthwise) Stretch fabric (Spandex or rib ) : -5.0% (Lengthwise) -6.0% (Lengthwise) -7.0% (Lengthwise) Color change: 4 Color staining: 4 Color change: 3-4 Color staining:3-4 47

48 TEST DESCRIPTION Color Fastness to Perspiration Color Fastness to Crocking (Rubbing) Color Fastness to Washing TEST METHOD (GB/T 8878)-GB/T 3922 /ISO 105 E04 (GB/T 8878)-GB/T 3920 /ISO 105 X12 GB/T 3921 A (1) /ISO 105 C10 Color change: 3 Color staining:3 Color change: 4 Color staining: 3-4 Color change: 3-4 Color staining:3 Color change: 3 Color staining:3 Dry: 4 Wet: 3 Dry: 3-4 Wet: 3 (dark color:2) Dry: 3 Wet: 2-3 (dark color:2) Printing: Dry: 3-4 Wet: 2-3 & Dry: 3 Wet: 2 Color change: 4 Color stain: 4 Color change: 3-4 Color stain: 3-4 Color change: 3 Color stain: 3 Printing: Color change: 3-4 Color stain: 3-4 & Color change: 3 Color stain: 3 48

49 Knit Underwear in Synthetic Fiber (Apply to synthetic fiber and blends with >50% synthetic fibre) TEST TEST METHOD DESCRIPTION FIBRE CONTENT Fiber Content (FZ/T 73024)-FZ/T 01053,GB/T 2910, GB/T 2911, FZ/T 01057, FZ/T 01095/ ISO 1833 PHYSICAL PROPERTIES Bursting Strength (FZ/T 73024)-GB/T 8878 (GB/T 19976, the steel Pilling Resistance DIMENSIONAL STABILITY Dimensional Stability to Washing ball diameter is 38mm ) (FZ/T 73024)-GB/T (FZ/T 73024)-GB/T8629 / ISO 6330 (not applicable for shorts) Single fiber: 0%; Result >15%: ±5%; Result 15%: ±30%,, Min 135 N for single, rib Min 220 N for double fabric, fuzz High class Grade 4.0 min & Grade 3.0 min For 50% cellulose fibre : -5.0% (Lengthwise) -5.0% to 0.0% (widthwise) -7.0% (Lengthwise) -8.0% to +2.0% (widthwise) -9.0% (Lengthwise) -10.0% to +2.0% (widthwise) COLORFASTNESS TESTS Color Fastness to Water (FZ/T 73024)-GB/T 5713 /ISO 105 E 01 Color Fastness to Perspiration Color Fastness to Crocking (Rubbing) (FZ/T 73024)-GB/T 3922 /ISO 105 E04 (FZ/T 73024)-GB/T 3920 /ISO 105 X12 For < 50% cellulose fibre : -3.0% (Lengthwise) -3.0% to 0.0% (widthwise) -5.0% (Lengthwise) -5.0% to +2.0% (widthwise) -7.0% (Lengthwise) -7.0% to +2.0% (widthwise) Color change: 4 Color staining: 3-4 Color change: 4 Color staining: 3-4 Dry: 4 Wet: 3 (dark 2-3) Color change: 3-4 Color staining:3 Color change: 3-4 Color staining:3 & Dry: 3 Wet: 2-3 (dark 2) Color change: 3 Color staining:3 Color change: 3 Color staining:3 Color Fastness to Washing (FZ/T 73024)-GB/T /ISO 105 C10 Printing: Dry: 3 Wet: 2-3 Color change: 4 Color staining: 3-4 Printing: Color change: 3-4 Color stain: 3-4 Printing & Dry: 3 Wet: 2 Color change: 3-4 Color staining:3 Printing & Color change: 3 Color stain: 3 Color change: 3 Color staining:3 49

50 2.2 Accessories Belts TEST DESCRIPTION Colorfastness Crocking Physical Construction / Workmanship review Cracking Resistance / Flex Test Salt Spray Test TEST METHOD* QB/T QB/T 2537 QB/T QB/T QB/T 2001 Annex B QB/T QB/T 3826: SALT SPRAY: SALT SPRAY Salt Spray QB/T 3832 MATERIAL/ COMPONENTS Textiles/Leather (Except White Color and non-dyed material) / Hardware Leather/PVC / PU (Body Material) Dry: Minimum 4.0 Wet: Minimum 3.0 The at least meets the PASS GRADE requirement. Details refer to Remark Table 1 & 2 No Cracking Hardware Minimum Grade 5 Size Review Belt Body Breakage Strength Belt Hole Tear Strength Belt Buckle Attachment Strength Pin Attachment Strength Children Safety Test QB/T QB/T QB/T QB/T QB/T Hardware Hardware Use and Abuse GB6675 / Hardware Labeling for China Market Certificate/ Hangtags Remarks QB/T / QB/T Length: +/-5% As Claim Width: +/-1% As Claim Minimum 300N (66 Pounds) Minimum 160N (35 Pounds) Minimum 180N (39 Pounds) Minimum 160N (39 Pounds) No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Color 6. Country of Origin 7. ion Date (Month & Year) 8. Materials 9. Standard 10. Quality Grade 11. Certificate (Inspection Logo) 12. Name & Address of Manufacturer / Diistributor 50

51 Table 1 Quality Grade Pass Grade Stitch length (6~12) needles/ 30mm (excluding decorative line) Seam margin 1.5 ~ 3.0mm (excluding decorative line) Stitch track Straight, uniform, consistent in elasticity, not skew. No empty needle, drop needle, skipping stitch, float, double needle Straight, uniform, consistent in elasticity, without obvious skewness. No empty needle, drop needle, skipping stitch, float, double needle Table 2 Quality Grade Pass Grade Surface Leather material Leather, synthetic leather Textile fabric surface Buckle Swing stitches Riveting pieces Belt holes Belt edge Belt tail Belt bottom Belt body Belt loop It is flat in surface, uniform in thickness, free from peeling, split face and split pulp. It is without creases, cuts, and without color difference It is smooth and uniform in surface, crack-free and without creases and scratches. Multi-layer belt is glued firmly together, without any crack. Without any bumps and knots and tracks. Smooth in surface, without breaks both in warp and in weft, and without floating thread and any defect. Flat in surface, uniform in thickness, free from peeling, split face and split pulp. It is without creases, cuts; it is by and large without color difference, and have 2 slight and unobvious cuts It is smooth and uniform in surface, crack-free and without creases and scratches. Multi-layer belt is glued firmly together, without any crack. Without any obvious bumps and knots and tracks. Smooth in surface, without breaks both in warp and in weft, and without floating thread. Less than 2 unobvious defects are allowed. No rust, no glitches, evenly coating, no scratches, & no burning, blistering, peeling, & decomposition missing. Uniform in thickness which shall be not less than 1.5mm No rust, no glitches, uniform coating, no scratches. Equal in distance, firm and correct in installation Fit closely with the buckle. Smooth and without marking Strong and round Smooth and flat by and large Tidy and clean, with smooth parts and without burr. It is set around the belt which fits well. No rust, no glitches, uniform coating, with slight scratches on its backside. Equal in distance, firm and correct in installation 51

52 2.2.2 Cold Weather Hat TEST DESCRIPTION Fiber Content Fiber Content Colorfastness Crocking Light TEST METHOD* Woven: FZ/T 82002; Knit: FZ/T GB GB/T 3920 Woven: FZ/T 82002; Knit: FZ/T GB/T 8427 MATERIAL/ COMPONENTS Textiles / Leather (Except White Color and non-dyed material) Textiles / Leather / PVC / PU Minimum 3.0 Comply with FZ/T Single Fiber: no tolerance 2. Blends >15%: +/-5% Blends 15%: +/-30% of the claimed fiber Dry: Minimum 3.0 Wet: Minimum 2.5 for Dark Colors Minimum 3.0 for Other Colors Perspiration Washing Water GB GB/T 3922 Textiles / Leather Minimum 3.0 Woven: FZ/T 82002; Knit: FZ/T 73002: GB/T Textiles (Except White Color and non-dyed material) Minimum 3.0 GB GB/T 5713 Textiles / Leather Minimum 3.0 Dry Cleaning Woven: FZ/T 82002; Knit: FZ/T GB/T 5711 Minimum 3.5 Physical Construction / Workmanship review Total Weight Children Safety Test Woven: FZ/T Knit: FZ/T Knit: FZ/T / Hardware Use and Abuse GB6675 / Hardware Labeling for China Market Permanent Label GB Certificate/ Hangtags GB Minimum -6% The at least meets the PASS GRADE requirement. Details refer to Remark Table 1 & 2 (Woven), 3 & 4 & 5 (Knit) No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 1. Fiber Content 2. Sizes 3. Care Instruction Details refer to Remark 6 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Country of Origin 6. Materials (Fiber Content) 7. Care Instruction 8. Standard 9. Quality Grade 10. Category A, B or C 11. Certificate (Inspection Logo) 12. Name & Address of Manufacturer / Distributor 13. Notes for Use and Storage Conditions if necessary Details refer to Remark 7 Remarks Table 1 52

53 Allowable size deviation of the main parts of finished products (in cm) Serial No Part Allowable size deviation 1 Inner perimeter of the hat opening Plush hat Mid-width of the hat ±0.3 3 Top mid-height of the hat ±0.3 4 Mid-height of the hat brim ±0.3 5 Mid-length of the hat peak ±0.2 6 Mid-heightof the hatband ±0.3 7 Mid-height of the earlap ±0.3 8 Mid-height of the hat ±0.2 9 Fore middle height of the eartap ± Rear middle height of the eartap ± Ribbon width of the hat opening ± Height of hat face ±0.4 Table 2 Stitch length density Item Stitch length (needle/3 cm) Remarks Terminator line Not less than 12 With the exception of special design Sewing stitch Not less than 9 - Table 3 Item Stitch length (needle/3cm) Remarks Terminator line 10~12 - Three-line sewing 9~11 With the exception of the elastic sewing Four-line sewing 9~11 - Table 4 Serial No Part title Measuring method 1 Length of the cap Laying down the cap, vertically measuring the cap from the top to the cap opening 2 Width of the cap opening 2 cm above the cap opening,parallel measuring the cap from left side to the right side 3 Width of the cap body,parallel measuring the cap from the left side to the right side 4 Length of the turned-over edge Measuring the cap from the top of the turned-over edge to the cap opening 5 Top diameter of the cap(bowler hat) Laying down the cap, measuring the top diameter of the cap 6 Cap opening diameter (bowler hat) Laying down the cap with cap opening upwards, measuring the diameter of the cap opening Table 5 Basis for the determination of quality defects Item Serial No Minor defects Major defects Serious defects Instruction 1 Trademark is not upright in body,not flat,obviously Skewing, there is color difference between the trademark stitch and trademark ground color Allowable deviation specification 2 Specification exceeds this standards below 50% 1. Permanent Label for Textile s and Apparel Remark 6 Incorrectly using of the instruction Specification exceeds this standards for 50% or above Lacunary in the instruction content Specification exceeds this standards for 100% or above According to GB Instruction for use of products of consumer interest Instructions for use of textiles and apparel, all the Textile s and Apparel sold in China are required to attach the legible label (i.e. permanent label) and be able to subject to use duration described in use instruction Contents of Permanent Label Permanent Label includes below information: d. Fiber Content (refer to FZ/T 01053) e. Sizes (refer to GB/T to GB/T ) f. Care Instruction 1. Washing Symbols (graphic symbols specified in GB/T 8685 and with their corresponding simple declaration text) 2. If symbols are not enough to explain, the short text can be added, but it shall be not in parallel with note to symbols meaning 53

54 1.2. How to show the Permanent Label The permanent label shall be permanently adhered on the suitable position of product: a. The label of size or specification 1. For apparel it can be sewn in middle of the collar. For the cover coat and business suit it can also sewn on the top or down edge of inside pocket of jacket; For the trouser or skirt on the lower edge of waistband. 2. For other textile products, e.g. scarf, towel etc, can be sewn on the corners b. The label of material compositions and contents, care instruction 1. The material composition and contents, care instruction can be indicated on a label together. 2. For apparel, it can be generally sewn on the lower middle position of left seam For the skirts and trouser can be sewn on the lower edge of waistband or upper position of skirt left seam, trouser side seam 3. For other textile products, e.g. scarf, towel etc, can be sewn on the corners 1 Content of Instruction Remark Name and address of the manufacturer It shall be marked the name and address that are registered according to law by the manufacturers of textiles and clothing. The product origin (country or region) and the name and address of the imported textiles and clothing that are registered according to law by the agent or importer or distributor shall be marked in Chinese. 1.2 name name shall indicate its real characteristics and shall meet the following REQUIREMENT: In case of specifications for product names existing in national standards or industry standards, these names shall be used In case of specifications for product names not existing in national standards or industry standards, common names or popular names that will not cause misunderstanding and confusion shall be used; For marking of "strange name" and "trade name", a name specified in or shall be clearly marked in same position. 1.3 models and specifications Marking of sizes or specifications of textile shall comply with the relevant national or industry standards. Type of clothes shall be indicated in accordance with the REQUIREMENT in GB / T ~ Composition and content of raw materials Name and content of composition of raw materials shall be marked, while the marking of fiber content shall be in accordance with the REQUIREMENT in FZ/T01053, please see Appendix A (Normative) for example. For leather garments, it shall mark the leather s type name which shall show the real characteristics of the products, and if there are any specifications in standards, the relevant national, industry or corporate standards shall be followed. 1.5 Washing Washing methods shall be provided with the graphical symbols given in GB/T8685, with a simple descriptive text corresponding to the graphic symbols being noted underline When the graphic symbols can not meet the needs, concise text can be given for description, but it shall not be placed side by side with the above said descriptive notes The letter A, P, F shall be added as dry cleaning symbols to illustrate the type of dry cleaning agent. (See Appendix B (Normative)). 1.6 Precautions of use and storage conditions Improper use may cause damage to the product, and the product shall be indicated with the precautions for use. If it is need to be stored, the storage methods shall be briefly indicated. 1.7 Lifetime of For product that needs to be used in a limited time period, it shall be marked with production date and the effective lifetime (date shall be marked in order of year, month, day). 1.8 Standards No. The number of all implemented national standards, industry standards or enterprise standards shall be marked. 1.9 quality rating For the product with its quality ratings clearly defined in Standards, it shall mark the quality ratings in accordance with the REQUIREMENT in relevant standards Quality certificate of product For qualified products produced domestically, each single product (sales unit) shall have its quality certificate of inspection. 2 Form of Instruction 2.1 The following form shall be used according to the characteristics of products a. The instructions directly printed or weaved on the product; b. Labels stitched, pasted, or hung on the product; c. The instructions directly printed on the product packaging; d. Washing methods include washing with water, chlorine bleaching, ironing, drying after washing, dry cleaning, and other methods. e. Labels attached on the product packaging; f. Materials provided along with the product information. 2.2 s sizes or specifications, the composition and content of used raw materials, washing method and other contents shall be in durable labels (see 3.4). In which, the composition and content of raw materials and washing methods, etc shall be marked in combination on one label. If the used durable label affects the use of products, such as in the case of fabric, yarn and sewing thread 54

55 and stocks and other products, the durable label shall not be used. 2.3 If the products are packaged, displayed or scrolled, and the consumer is not easy to find the information on the instruction label, you shall give this information in other forms of instructions. 2.4 When several types of instructions were used simultaneously, it shall ensure the consistency of their contents. 3 Placement of instructions 3.1 The instructions shall be attached to the product or packaging on an obvious parts or an appropriate parts. 3.2 The instructions shall be provided in single product unit or sale unit. 3.3 Location of durable label The durable label shall be permanently attached to the product in an appropriate location Label location of clothing product Type signs or specifications and other kind of labels for apparel products shall be normally in placed or sewn in center of back collar. In which, the labels for coats and suits can also be sewn on upper edge or lower edge of inner placket of front waistband; labels for pants and skirt can be sewn on lower edge of inner waist Composition and content of raw materials and washing methods of clothing products shall be generally sewn on middle and lower part of left seam. Labels for pants and skirt can be sewn on lower edge of inner waist or left seam of skirt or upper part of pants seam Label for products of scarves and shawls can be sewn in edges or corners Labels of ties shall be sewn on wide or narrow part of joint seams of tie back Labels on household textiles (tablecloths, bed sheets, towels, bedspreads, blankets, etc.) shall be sewn on edges or corners. 3.4 Placement of instruction labels of fabric, yarn and sewing thread, socks and other textile products Instruction labels of cloth shall be placed in one of the following ways: a. The label or tag attached to end of fabric rolls; b. The label or tag printed or woven on the weaving edge Instruction content of yarn and sewing thread shall be marked on tag or shell ring of coil, ball and hoop Instruction content socks can be marked on the label at top of socks Label for other textile product shall be placed on its appropriate locations. 3.5 Labels of special technological products shall be placed according to the specific needs. 55

56 Glove TEST DESCRIPTION Colorfastness Crocking TEST METHOD* QB/T 1584 (for leather glove) / QB/T 1616 (for sport leather glove): Leather: QB/T 2537 Textiles: GB GB/T 3920 MATERIAL/ COMPONENTS Textiles/Leather (Except White Color and non-dyed material) Leather: Dry (50 Cycles): Minimum 3.5 Wet (10 Cycles): Minimum 3.0 Textiles: Dry: Minimum 3.0 Wet: Minimum 3.0 Perspiration GB GB/T 3922 Textiles/Leather Minimum 3.0 Water GB GB/T 5713 Textiles/Leather Minimum 3.0 Physical Construction / Workmanship review QB/T 1584 (for leather glove) / QB/T 1616 (for sport leather glove) / Hardware The at least meets the PASS GRADE requirement. Details refer to Remarks (for Leather Glove), & Remarks (for sport leather glove) Trapezoid Tear Strength Determination of tensile strength and percentage extension Determination of distension and strength of grain-ball burst test Children Safety Test QB/T 1584 (for leather glove) / QB/T 1616 (for sport leather glove): - QB/T 2711 Textiles/Leather /PVC/PU For Leather Glove: Sheepskin / Pigskin: Minimum 15N (3.3 Pounds) Cowhide/ Horsehide / Mule Hide: Minimum 18N (4.0 Pounds) Split leather and leather from other small animals: Minimum 12N (2.6 Pounds) For Sport Leather Glove: Minimum 10N (2.2 Pounds) QB/T QB/T 2710 Leather Range: 25-50% QB/T QB/T 2710 Leather Minimum 8mm Use and Abuse GB6675 / Hardware Labeling for China Market (for leather glove) Permanent Labels Certificate / Hangtags QB/T 1584 (for leather glove) / QB/T 1616 (for sport leather glove) QB/T 1584 (for leather glove) / QB/T 1616 (for sport leather glove) - Leather - Leather No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 1. Size 2. Materials Compositions and Contents 3. Country of Origin 4. Brand Name 5. Certificate (Certification Logo) 6. Name & Address of Manufacturer / Distributor 1. Name 2. Standard 3. Size 4. Batch Number (Style Number) 5. Materials Compositions and Contents 6. Certification Logo 56

57 Labeling for China Market (for textile glove) Permanent Label Certificate/ Hangtags GB (for textile glove) GB (for textile glove) - Textile - Textile 1. Fiber Content 2. Sizes 3. Care Instruction Details refer to Remark 1 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Country of Origin 6. Materials (Fiber Content) 7. Care Instruction 8. Standard 9. Quality Grade 10. Category A, B or C 11. Certificate (Inspection Logo) 12. Name & Address of Manufacturer / Distributor 13. Notes for Use and Storage Conditions if necessary Details refer to Remark 2 57

58 Remarks (for Leather Glove) Table 1 Specifications and allowable dimensional deviation (in mm) Item Model Allowable deviation Men Middle finger length 士 1.0 Length of hand-stretch 士 1.0 Item Model Allowable deviation Women Middle finger length 士 1.0 Length of hand-stretch 士 1.0 Table 2 Specifications and allowable dimensional deviation (in mm) Item Model Allowable deviation Men Width 士 1.5 Item Model Allowable deviation Women Width 士 Raw materials Remark Leather According to the specification in QB/T Thickness of leather Not less than 0.5mm Leather surface It shall be of smooth surface, uniform thickness, no breakage, with scattered small scars and small spots and other minor injuries at insignificant areas. No cleaved surface and split pulp, and with no lost of pulp and other phenomenon. It shall be with uniform color by and large, not fading Leather body It shall be soft, full and flexible, with a comfortable feel Inside of leather It shall be not greasy, wounds depth shall be less than one half of the thickness, which shall be repaired and filled with glue Incisions Color of incision shall be consistent with color of surface Appearance of a same pair of gloves shall be proportional in general Materials of artificial leather and synthetic leather It shall be selected in accordance with the relevant standards, and shall not have any obvious tracks, bumps and knots Textile materials It shall be selected in accordance with the relevant standards, and shall not have any taking out of threads, skipping threads, and shall match with the outside materials. 1.2 Supplementary materials Inner Lining Length, width, flexibility shall conform to the outside material, comfortable in wearing, no holes, broken in seams and other phenomenon. Five fingers of lining shall be seamed firmly with five fingers of fabric, without pleats and crimples on the whole lining material. Fur lining shall be soft, without serious hair loss, fading, odor and other phenomenon, smooth and straight in the stitching seams Zipper. No teeth dislocation, no teeth missing, smooth and free in pulling together Buttons and other accessories It shall be firmly installed, flexible in use, no glitches, and no rust. The same pair of gloves shall be of coordination and consistent at the installation area Label It shall be clear and tidy in appearance, smooth and straight and firm in binding. 1.3 Sewing requirements Sewing appearance Uniform and neat in stitches, appropriate in thread at bottom and surface, back stitches shall be in the original pinhole, and without second track of thread Distance of stitches 58

59 14 to 16 stitches shall be made within a distance of 30 mm for machine made gloves, 6 to 7 stitches shall be made within a distance of 30 mm for hand made gloves Margin It shall be 1.0 mm ~ 1.5 mm for open seam and shall be 1.5mm ~ 2.0mm for dark seam, with a middle distance of 1.5mm ~ 2.0 mm between two tracks Five fingers Round and correct in finger top, flat and smooth in fork angle and hukou, symmetrical for the thumb in a tilted angle, smooth and circular in the seamed thumb area Trundle jaw It shall be uniform in thickness, same in length of fork part in a same glove (with allowable tolerance of ± 3 mm) and shall be neatly trimmed at the back Back tendon It shall be symmetrical and tidy in a same glove, with seam being fluent and straight and smooth. 1.4 Overall appearance It shall be smooth and straight as a whole, appropriate in elasticity, no exposed end of thread, and shall not have stains, burning mark, cut, button loosening, fall and damage of zipper heads, serious odors and other defects. Left and right hand shall be consistent basically in a same pair of gloves. 2 Test methods 2.1 Device Steel ruler, with the smallest scale of 0.5mm 2.2 Specification Spread out the glove, measure with a steel ruler with a graduation of 0.5 mm. Schematic diagram of measurement of main parts of finished gloves are as in Figure 1. Middle finger length Length of hand-stretch Width Figure 1 Schematic diagram of measurement of the main parts of finished gloves Table 4 For products classification Category 1 Category 2 Category 3 Category 4 Sheepskin Pigskin Cowhide, horsehide, mule hide Split leather and leather from other small animals Remark 5 1 Physical and Chemical Property It shall comply with the specification in Table 2. The thickness of leather of Category 1, 2 and 3 shall not be more than 0.5 mm, with its physical and chemical performance shall be consistent with the provisions for Category 4. 2 Sensory requirements 2.1 Leather body shall be smooth, soft, plump and elastic. 2.2 The whole leather shall be by and large uniform in thickness, and shall be clean, non greasy, and without serious odor. 2.3 Incision of leather shall be consistent with the color of leather surface, evenly in dyeing; color difference in whole leather shall be not more than half level. It shall be crack-free in surface of leather; the finished leather coating shall be firm in bonding and without crazing of leather, evenly in fine hair of suede leather. Remarks (for Sport Leather Glove) Table 1 Specifications and allowed deviation of size for arch gloves (in mm) Item Model Allowable deviation Men Middle finger length 士 3.0 Length of hand-stretch 士 3.0 Item Model Allowable 59

60 deviation Women Middle finger length 士 3. Length of hand-stretch 士 3.0 Table 2 Specifications and allowed deviation of size for arch gloves (in mm) Item Modl Allowable deviation Men Width 士 4.0 Item Model Allowable deviation Women Width 士 4.0 Table 3 Specifications and allowed deviation of size for straight gloves (I) (in mm) Item Model Allowable deviation Men Middle finger length 士 3.0 Length of hand-stretch 士 3.0 Item Model Allowable deviation Wome n Middle finger length 士 3.0 Length of hand-stretch 士 3.0 Table 4 Specifications and allowed deviation of size for straight gloves (in mm) Item Model Allowable deviation Men Width 士 4.0 Item Model Allowable deviation Women Width 士 4.0 Remark 5 1 Materials 1.1 Leather According to the specification in QB/T Thickness of leather Not less than 0.45 mm Leather surface It shall be with smooth surface, uniform thickness, and no breakage in main area, with scattered small scars and small spots and other minor injuries at insignificant areas. No cleaved surface and split pulp, and with no lost of pulp and other phenomenon. It shall be with uniform color by and large, not fading Leather body It shall be soft, full and flexible, with a comfortable feel Inside of leather It shall be non-greasy and the wounds depth shall be less than one third of the thickness, which shall be repaired and filled with glue Incisions Color of incision shall be consistent with color of surface Appearance of a same pair of gloves shall be proportional in general. 1.2 Materials of artificial leather and synthetic leather It shall be selected in accordance with the relevant standards, and shall be soft and elastic, and the surface coating material shall be bonded firmly with its base, and with consistent appearance, and no defects on its surface. 1.3 Textile fabrics It shall be with same color, and yarn shall be woven tightly in warp and weft, with no thread skipping and no thread drawn out. 2 Supplementary materials 2.1 Inner lining Length, width and flexibility shall be consistent with the outside material, comfortable in wearing, with fingers and jaws filling in place, having gaps between linings and the outside material, smooth and flat and without raised wrinkles. 2.2 Zipper No teeth dislocation, no teeth missing, smooth and free in pulling together. 2.3 Buttons and other accessories It shall be firmly installed, flexible in use, no glitches, and no rust. The same pair of gloves shall be of coordination and consistent at the installation area. 60

61 2.4 Label It shall be clear and tidy in appearance, smooth and straight and firm in binding. 3 Sewing requirements 3.1 Sewing appearance 3.2 It shall be smooth and straight in stitches track, uniform and tidy in needle distance, consistent in elasticity of bottom and surface thread, smooth and flat in seam and without raised wrinkles and three stitches at repeat stitches. 3.3 Distance of stitches Needle distance at open thread shall be 12 stitches / 30mm ~ 15 stitches / 30mm, while needle distance at hidden thread shall be 15 stitches / 30mm ~ 17 stitches / 30mm. 3.4 Five fingers Round and correct in finger top, with fingers tilt or open not less than 30 degrees. 3.5 Roller jaw It shall be in uniform width and shall be symmetrical. 4 Overall appearance It shall be smooth and straight as a whole, appropriate in elasticity, no exposed end of thread, and shall not have stains, burning mark, cut, button loosening, fall and damage of zipper heads, serious odors and other defects. Middle finger length Middle finger length Length of handstretch Length of handstretch Width Width Figure 1 Schematic diagram of measurement of the main parts of arc gloves Figure 2 Schematic diagram of measurement of the main parts of straight gloves Width 61

62 Remarks (for textile glove) Remark 1 1. Permanent Label for Textile s and Apparel According to GB Instruction for use of products of consumer interest Instructions for use of textiles and apparel, all the Textile s and Apparel sold in China are required to attach the legible label (i.e. permanent label) and be able to subject to use duration described in use instruction. 1.1 Contents of Permanent Label Permanent Label includes below information: a. Fiber Content (refer to FZ/T 01053) b. Sizes (refer to GB/T to GB/T ) c. Care Instruction 1. Washing Symbols (graphic symbols specified in GB/T 8685 and with their corresponding simple declaration text) 2. If symbols are not enough to explain, the short text can be added, but it shall be not in parallel with note to symbols meaning 1.2 How to show the Permanent Label The permanent label shall be permanently adhered on the suitable position of product: a. The label of size or specification 1. For apparel it can be sewn in middle of the collar. For the cover coat and business suit it can also sewn on the top or down edge of inside pocket of jacket; For the trouser or skirt on the lower edge of waistband. 2. For other textile products, e.g. scarf, towel etc, can be sewn on the corners b. The label of material compositions and contents, care instruction 1. The material composition and contents, care instruction can be indicated on a label together. 2. For apparel, it can be generally sewn on the lower middle position of left seam For the skirts and trouser can be sewn on the lower edge of waistband or upper position of skirt left seam, trouser side seam 3. For other textile products, e.g. scarf, towel etc, can be sewn on the corners Remark 2 1 Content of Instruction 1.1 Name and address of the manufacturer It shall be marked the name and address that are registered according to law by the manufacturers of textiles and clothing. The product origin (country or region) and the name and address of the imported textiles and clothing that are registered according to law by the agent or importer or distributor shall be marked in Chinese. 1.2 name name shall indicate its real characteristics and shall meet the following REQUIREMENT: In case of specifications for product names existing in national standards or industry standards, these names shall be used In case of specifications for product names not existing in national standards or industry standards, common names or popular names that will not cause misunderstanding and confusion shall be used; For marking of "strange name" and "trade name", a name specified in or shall be clearly marked in same position. 1.3 models and specifications Marking of sizes or specifications of textile shall comply with the relevant national or industry standards. Type of clothes shall be indicated in accordance with the REQUIREMENT in GB / T ~ Composition and content of raw materials Name and content of composition of raw materials shall be marked, while the marking of fiber content shall be in accordance with the REQUIREMENT in FZ/T01053, please see Appendix A (Normative) for example. For leather garments, it shall mark the leather s type name which shall show the real characteristics of the products, and if there are any specifications in standards, the relevant national, industry or corporate standards shall be followed. 1.5 Washing Washing methods shall be provided with the graphical symbols given in GB/T8685, with a simple descriptive text corresponding to the graphic symbols being noted underline When the graphic symbols can not meet the needs, concise text can be given for description, but it shall not be placed side by side with the above said descriptive notes The letter A, P, F shall be added as dry cleaning symbols to illustrate the type of dry cleaning agent. (See Appendix B (Normative)). 1.6 Precautions of use and storage conditions Improper use may cause damage to the product, and the product shall be indicated with the precautions for use. If it is need to be stored, the storage methods shall be briefly indicated. 1.7 Lifetime of For product that needs to be used in a limited time period, it shall be marked with production date and the effective lifetime (date shall be marked in order of year, month, day). 1.8 Standards No. The number of all implemented national standards, industry standards or enterprise standards shall be marked. 1.9 quality rating For the product with its quality ratings clearly defined in Standards, it shall mark the quality ratings in accordance with the REQUIREMENT in relevant standards Quality certificate of product 62

63 For qualified products produced domestically, each single product (sales unit) shall have its quality certificate of inspection. 2 Form of Instruction 2.1 The following form shall be used according to the characteristics of products a. The instructions directly printed or weaved on the product; c. Labels stitched, pasted, or hung on the product; d. The instructions directly printed on the product packaging; e. Washing methods include washing with water, chlorine bleaching, ironing, drying after washing, and dry cleaning, and other methods. f. Labels attached on the product packaging; g. Materials provided along with the product information. 2.2 s sizes or specifications, the composition and content of used raw materials, washing method and other contents shall be in durable labels (see 3.4). In which, the composition and content of raw materials and washing methods, etc shall be marked in combination on one label. If the used durable label affects the use of products, such as in the case of fabric, yarn and sewing thread and stocks and other products, the durable label shall not be used. 2.3 If the products are packaged, displayed or scrolled, and the consumer is not easy to find the information on the instruction label, you shall give this information in other forms of instructions. 2.4 When several types of instructions were used simultaneously, it shall ensure the consistency of their contents. 3 Placement of instructions 3.1 The instructions shall be attached to the product or packaging on an obvious parts or an appropriate parts. 3.2 The instructions shall be provided in single product unit or sale unit. 3.3 Location of durable label The durable label shall be permanently attached to the product in an appropriate location Label location of clothing product Type signs or specifications and other kind of labels for apparel products shall be normally in placed or sewn in center of back collar. In which, the labels for coats and suits can also be sewn on upper edge or lower edge of inner placket of front waistband; labels for pants and skirt can be sewn on lower edge of inner waist Composition and content of raw materials and washing methods of clothing products shall be generally sewn on middle and lower part of left seam. Labels for pants and skirt can be sewn on lower edge of inner waist or left seam of skirt or upper part of pants seam Label for products of scarves and shawls can be sewn in edges or corners Labels of ties shall be sewn on wide or narrow part of joint seams of tie back Labels on household textiles (tablecloths, bed sheets, towels, bedspreads, blankets, etc.) shall be sewn on edges or corners. 3.4 Placement of instruction labels of fabric, yarn and sewing thread, socks and other textile products Instruction labels of cloth shall be placed in one of the following ways: a. The label or tag attached to end of fabric rolls; b. The label or tag printed or woven on the weaving edge Instruction content of yarn and sewing thread shall be marked on tag or shell ring of coil, ball and hoop Instruction content socks can be marked on the label at top of socks Label for other textile product shall be placed on its appropriate locations. 3.5 Labels of special technological products shall be placed according to the specific needs. 63

64 Scarf TEST DESCRIPTION Fiber Content Fiber Content TEST METHOD* Silk Scarves: FZ/T 43010; Scarves and Shawls: FZ/T MATERIAL/ COMPONENTS Comply with FZ/T Single Fiber: no tolerance 2. Blends >15%: +/-5% Blends 15%: +/-30% of the claimed fiber Care Label Care Label Verification Colorfastness Silk Scarves: FZ/T 43010; Scarves and Shawls: FZ/T Shrinkage - Machine Wash: Scarves and Shawls/Silk Scarves/Synthetic Scarves- 6x+2%/-5x+3%/3x3% Shrinkage - Dry Cleaning: Scarves and Shawls/Silk Scarves/Synthetic Scarves: - 3x+2%/-4x+2%/-4x+2% Dry: Minimum 3.0 Crocking Dry Cleaning Light Washing GB GB/T 3920 Silk Scarves: FZ/T Scarves and Shawls: FZ/T Silk Scarves: FZ/T Scarves and Shawls: FZ/T Silk Scarves: FZ/T Scarves and Shawls: FZ/T Textiles/Leather (Except White Color and non-dyed material) Textiles/Leather /PVC/PU Minimum 3.0 Textiles (Except White Color and non-dyed material) Wet: (i) Scarves and Shawls: Minimum 3.0 for other colors Minimum 2.5 for Dark colors (ii) Silk Scarves Minimum 2.5 for other colors Minimum 2.0 for Dark colors Synthetic Scarves: Minimum 3.0 Scarves and Shawls: Color Change: Minimum 3.5 Color Stain: Minimum 3.5 Silk Scarves/Synthetic Scarves: Color Change: Minimum 3.0 Color Stain: Minimum 3.0 Scarves and Shawls: Color Change: Minimum 3.0 Color Stain: Minimum 3.0 Silk Scarves: Color Change: Minimum 3.0 Color Stain: Minimum 2.5 Perspiration GB GB/T 3922 Textiles/Leather Synthetic Scarves: Color Change: Minimum 3.5 Color Stain: Minimum 3.0 Scarves and Shawls: Color Change: Minimum 3.0 Silk Scarves/Synthetic Scarves: Color Change: Minimum 3.5 Water GB GB/T 5713 Textiles/Leather Color Stain: Minimum 3.0 Scarves and Shawls: Color Change: Minimum 3.0 Silk Scarves/Synthetic Scarves: Color Change: Minimum 3.5 Color Stain: Minimum

65 Physical Construction / Workmanship review Silk Scarves: FZ/T 43010; Scarves and Shawls: FZ/T / Hardware The at least meets the PASS GRADE requirement. Details refer to Remark Table 1, 2 & 3 (Scarves and Shawls), Table 4 & 5 & 6 (Silk) Tearing Strength: Single Tear Method Children Safety Test Scarves and Shawls Only: FZ/T (Exclude Silk Scarves/Synthetic Scarves) Use and Abuse GB6675 / Hardware Labeling for China Market Permanent Label GB Certificate/ Hangtags GB Minimum 7N (1.5 Pounds) No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 1. Fiber Content 2. Sizes 3. Care Instruction Details refer to Remark 7 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Country of Origin 6. Materials 7. Care Instruction 8. Standard 9. Quality Grade 10. Category A, B or C 11. Certificate (Inspection Logo) 12. Name & Address of Manufacturer / Distributor 13. Notes for Use and Storage Conditions if necessary Details refer to Remark 8 65

66 Remarks Table 1 Allowable dimensional deviation of finished products. Item Requirements Dimensional deviation Dimensions shall be 55 or below. Dimensions shall be over ~ ~-3.0 Difference in length between sides Note: Only symmetric sides are examined for the difference in length between sides. Table 2 Defects in appearance - Allowance level of defects in appearance for finished products. Name of defects Allowance level Linear defects in warp and wft 2cm or less Strip or block defects 1cm or less Skew defects in warp and weft 5% Bar Minor, 3cm or les Oil, rust, color stains Minor, 0.5 cm 3 or less Breakage Not alowed Note 1: Defects that are not double thicker than yarn shall be seen as linear defects. Note 2: Strip or block defects shall be calculated according to their maximum length. Note 3: Square products shall only be examined for skew defects in warp and weft. Note 4: All that two or more threads in warp and weft break shall be seen as breakage defects. Note 5: Defects that can be distinguished only by careful visual check at a distance of 60cm away from the sample shall be seen as minor defects. Table 3 Item No. Minor defects Major defects Serious defects Instructions 1 Trademark is not upright and not correct and is significantly skewed; color of line binding trademark is incompatible with trademark background. Content of instructions is not accurate. Content of instructions is incomplete. Specification Specification and color of the used fabric are clearly incompatible with Design Book and Standard Sample. Surface defects 3 Deviation is within 50% of the value specified in this Standard. 4 Minor stains in surface; linear defects are beyond the value specified in this Standard. Stitch density 5 For Hand hemming, the density is one stitch lower than as specified in this Standard; for others, it shall be not over 2 stitches lower than as specified in this Standard. Stitches quality in appearance Deviation is 50% or above of the value specified in this Standard. With strip or block defects, skewed in warp and weft, slight bar, oil, rust and color stains beyond the value specified in this Standard. For hand hemming, the density is one stitch or above lower than as specified in this Standard; for others, it is 2 stitches or above lower than as specified in this Standard. 6 - Specification of seam thread is not in conformity with the requirements; color difference between seam thread and fabric is within 3 levels or below.- 7 Thread in surface and in bottom is slightly inappropriate in degree of tightness. 8 Stitches are not straight and smooth. 9 Two skipping stitches within one side. Deviation is 100% or above of the value specified in this Standard. With obvious bar, oil, rust and color stains. - Thread in surface and in bottom is seriously inappropriate in degree of tightness, which affects firmness in seam. Curling or corner folded - Continuous skipping stitches or over two skipping stitches within one side Loose back stitching at fluctuations - in the needle Break in stitches, seam slack, unstitched Embroidery stitch is obviously irregular; embroidered patterns Embroidered patterns is incomplete, and loss of stitches

67 wrinkling; significant loss of trace Fall or loss of ornaments. 14 Color difference on the same finished products is half level lower than as specified in this Standard. Color difference on the same finished products is one level lower than as specified in this Standard. Color difference on the same finished products is more than one level lower than as specified in this Standard. 15 Corners are not smooth and tidy, Serious curling or comer folded. - curling slightly. 16 There are more than 2 dead - - threads of over 1.5 cm in length With obvious dislocation in the - whole pattern Fringes and other decorative - accessories are irregular, which significantly affects the appearance. 19 Not smooth and tidy in ironing, with reflective light. Slight change in color, with stubborn crimple. With deterioration, or dilapidated. Note 1: The above mentioned defects shall be calculated in accumulation by serial number. Note 2: Defects not covered in the table shall be determined as appropriate with reference to similar defects according to Defect Classification Rules, Note 3: Any lost in procedures, less in work or wrong in sequence shall all be seen as major defects. Lack of parts shall be seen as serious defects. Table 4 Provisions for deviation in size of silk scarves (in cm) Item Requirements Dimensions shall be 55 or below Dimensions shall be over 55. Deviation in size 士 2.0 士 3.0 Difference in length between symmetric sides Table 5 Defects in appearance - Provisions for defects in appearance Name of defects Allowance level Linear defects in warp and weft a One such defect is allowed within a distaneo2cm. Slight strip or block defects b One such defect is allowed within a distance of 1cm. Bar Slight; One such defect is allowed within a distance of 3cm. Breakage c Not allowed Dirty or color stains Not allowed Skew in weft 3% a Defects that are not double thicker than yarn shall be seen as linear defects. b Strip or block defects shall be calculated according to their maximum length. c All that two or more thread in warp and weft break shall be seen as breakage. Table 6 Basis for determination of defects in appearance Item No. Minor defects Major defects Serious defects Instructions 1 Trademark is not upright, not correct or is significantly skewed; color of line binding trademark is incompatible with trademark background. Deviation in size Color difference Appearance Sewing Quality 2 Deviation in size is within 50% of the value specified in this Standard. 3 Color difference on the same product is less than half level lower than as specified in this Standard. 4 Corners are not smooth and tidy, with slight hairy corner, loosen corner, corner folded, and right angle is not square and straight. Content of instructions is not accurate. Deviation in size is 50% or over of the value specified in this Standard. Color difference on the same product is less than one level lower than as specified in this Standard. With serious hairy corner, loosen corner and corner folded Content of instructions is incomplete. Deviation in size is over 100% of the value specified in this Standard. Color difference on the same product is more than 1 level lower than as specified in this Standard. - 5 With one slight hairy corner, loosen With one serious hairy corner, - corner and corner folded loosen corner and corner folded 6 - Two skipping stitches in one side. Continuous skipping stitches or over two skipping stitches within one side. 7 - Loose back stitching at fluctuations in the needle. - 67

68 8 - - Break in stitches, lost seam slack, unstitched. 9 - Trace of seam threads is not - straight and smooth. 10 Thread in surface and in bottom is slightly inappropriate in degree of - tightness. - Thread in surface and in bottom is seriously inappropriate in degree of tightness, which affects firmness in 11 - Embroidery stitch track is obviously irregular; embroidered patterns wrinkling; significant loss of trace. 12 Not smooth and tidy in ironing, with Slight change in color, with brilliant light. stubborn crimple With dislocation in whole pattern which is not more than 2cm and will not affect the appearance significantly. 14 For drop thread, skipping stitch, lost needle and float, each is not more than 1cm (including 1cm) For drop thread, skipping stitch, lost needle and float, each is over 1cm (including 2cm) 15 - There are more than 2 dead threads of over 1.5 cm in length Fringes and other decorative accessories are irregular, which significantly affects the appearance. 17 For hand hemming, it shall be one stitch lower than as specified in this Standard; for others, they shall be not more than 2 stitches lower than as specified in this Standard. 18 Slight dirty and color stains on surface; linear defects are over the value specified in this Standard. 19 A few residues at burn-out printing area For hand hemming, it shall be more than one stitch lower than as specified in this Standard; for others, they shall be more than 2 stitches lower than as specified in this Standard. With strip or block defects, skewed in weft, slight bar, dirty and color stains over the value specified in this Standard. A few residues at burn-out printing area; slight yellowing at burn-out printing area. seam. Embroidered patterns is incomplete, and loss of stitches. With deterioration, or dilapidated. With dislocation in whole pattern which will affect the appearance. For drop thread, skipping stitch, lost needle and float, each is over 2cm With obvious bar, dirty and color stains Yellowing at back of burn-out printing area, with incomplete burnout printing. Note 1: The above mentioned defects shall be calculated in accumulation by serial number. Note 2: Defects not covered in this table shall be determined as appropriate with reference to similar defects according to requirements in standard. Note 3: Any lost in procedures, less in work or wrong in sequence shall all be seen as important defects. Lack of parts shall be seen as serious defects. 2. Permanent Label for Textile s and Apparel Remark 7 According to GB Instruction for use of products of consumer interest Instructions for use of textiles and apparel, all the Textile s and Apparel sold in China are required to attach the legible label (i.e. permanent label) and be able to subject to use duration described in use instruction. 1.1 Contents of Permanent Label Permanent Label includes below information: a. Fiber Content (refer to FZ/T 01053) b. Sizes (refer to GB/T to GB/T ) c. Care Instruction 1. Washing Symbols (graphic symbols specified in GB/T 8685 and with their corresponding simple declaration text) 2. If symbols are not enough to explain, the short text can be added, but it shall be not in parallel with note to symbols meaning 1.2 How to show the Permanent Label The permanent label shall be permanently adhered on the suitable position of product: a. The label of size or specification 1. For apparel it can be sewn in middle of the collar. For the cover coat and business suit it can also sewn on the top or down edge of inside pocket of jacket; For the trouser or skirt on the lower edge of waistband. 2. For other textile products, e.g. scarf, towel etc, can be sewn on the corners b. The label of material compositions and contents, care instruction 1. The material composition and contents, care instruction can be indicated on a label together. 68

69 2. For apparel, it can be generally sewn on the lower middle position of left seam For the skirts and trouser can be sewn on the lower edge of waistband or upper position of skirt left seam, trouser side seam 3. For other textile products, e.g. scarf, towel etc, can be sewn on the corners Remark 8 1 Content of Instruction 1.1 Name and address of the manufacturer It shall be marked the name and address that are registered according to law by the manufacturers of textiles and clothing. The product origin (country or region) and the name and address of the imported textiles and clothing that are registered according to law by the agent or importer or distributor shall be marked in Chinese. 1.2 name name shall indicate its real characteristics and shall meet the following REQUIREMENT: In case of specifications for product names existing in national standards or industry standards, these names shall be used In case of specifications for product names not existing in national standards or industry standards, common names or popular names that will not cause misunderstanding and confusion shall be used; For marking of "strange name" and "trade name", a name specified in or shall be clearly marked in same position. 1.3 models and specifications Marking of sizes or specifications of textile shall comply with the relevant national or industry standards. Type of clothes shall be indicated in accordance with the REQUIREMENT in GB / T ~ Composition and content of raw materials Name and content of composition of raw materials shall be marked, while the marking of fiber content shall be in accordance with the REQUIREMENT in FZ/T01053, please see Appendix A (Normative) for example. For leather garments, it shall mark the leather s type name which shall show the real characteristics of the products, and if there are any specifications in standards, the relevant national, industry or corporate standards shall be followed. 1.5 Washing Washing methods shall be provided with the graphical symbols given in GB/T8685, with a simple descriptive text corresponding to the graphic symbols being noted underline When the graphic symbols can not meet the needs, concise text can be given for description, but it shall not be placed side by side with the above said descriptive notes The letter A, P, F shall be added as dry cleaning symbols to illustrate the type of dry cleaning agent. (See Appendix B (Normative)). 1.6 Precautions of use and storage conditions Improper use may cause damage to the product, and the product shall be indicated with the precautions for use. If it is needed to be stored, the storage methods shall be briefly indicated. 1.7 Lifetime of For product that needs to be used in a limited time period, it shall be marked with production date and the effective lifetime (date shall be marked in order of year, month, day). 1.8 Standards No. The number of all implemented national standards, industry standards or enterprise standards shall be marked. 1.9 quality rating For the product with its quality ratings clearly defined in Standards, it shall mark the quality ratings in accordance with the REQUIREMENT in relevant standards Quality certificate of product For qualified products produced domestically, each single product (sales unit) shall have its quality certificate of inspection. 2 Form of Instruction 2.1 The following form shall be used according to the characteristics of products a. The instructions directly printed or weaved on the product; b. Labels stitched, pasted, or hung on the product; c. The instructions directly printed on the product packaging; d. Washing methods include washing with water, chlorine bleaching, ironing, drying after washing, and dry cleaning, and other methods. e. Labels attached on the product packaging; f. Materials provided along with the product information. 2.2 s sizes or specifications, the composition and content of used raw materials, washing method and other contents shall be in durable labels (see 3.4). In which, the composition and content of raw materials and washing methods, etc shall be marked in combination on one label. If the used durable label affects the use of products, such as in the case of fabric, yarn and sewing thread and stocks and other products, the durable label shall not be used. 2.3 If the products are packaged, displayed or scrolled, and the consumer is not easy to find the information on the instruction label, you shall give this information in other forms of instructions. 2.4 When several types of instructions were used simultaneously, it shall ensure the consistency of their contents. 3 Placement of instructions 3.1 The instructions shall be attached to the product or packaging on an obvious parts or an appropriate parts. 3.2 The instructions shall be provided in single product unit or sale unit. 3.3 Location of durable label The durable label shall be permanently attached to the product in an appropriate location Label location of clothing product Type signs or specifications and other kind of labels for apparel products shall be normally in placed or sewn in center of back collar. In which, the labels for coats and suits can also be sewn on upper edge or lower edge of inner placket of front waistband; labels for pants and skirt can be sewn on lower edge of inner waist. 69

70 Composition and content of raw materials and washing methods of clothing products shall be generally sewn on middle and lower part of left seam. Labels for pants and skirt can be sewn on lower edge of inner waist or left seam of skirt or upper part of pants seam Label for products of scarves and shawls can be sewn in edges or corners Labels of ties shall be sewn on wide or narrow part of joint seams of tie back Labels on household textiles (tablecloths, bed sheets, towels, bedspreads, blankets, etc.) shall be sewn on edges or corners. 3.4 Placement of instruction labels of fabric, yarn and sewing thread, socks and other textile products Instruction labels of cloth shall be placed in one of the following ways: a. The label or tag attached to end of fabric rolls; b. The label or tag printed or woven on the weaving edge Instruction content of yarn and sewing thread shall be marked on tag or shell ring of coil, ball and hoop Instruction content socks can be marked on the label at top of socks Label for other textile product shall be placed on its appropriate locations. 3.5 Labels of special technological products shall be placed according to the specific needs. 70

71 2.2.3 Electrical & Electronic s Digital Camera TEST DESCRIPTION Labeling Marking Instruction Physical Environmental test - high temperature storage test Environmental test - low temperature storage test Environmental test - low temperature operation test TEST METHOD* JB/T Section 8.1 JB/T Section 8.2 JB/T Section Section JB/T Section Section JB/T Section Section MATERIAL/ COMPONENTS / Instruction must bear: - Trademark or manufactuer name - Camera model no. - Serial no. Package and instruction should bear the product name, model number, functional parameter and grade, company name and address With packaging and without being powered, after being stored for 24hs under 60 and stabilizing for 8hs under normal temperature, all functions and operations shall be normal. With packaging and without being powered, after being stored for 24hs under -20 and stabilizing for 8hs under normal temperature, all functions and operations shall be normal. All functions and operations shall be normal after placing the powered item without packaging in a constant temperature of 0 for 2 hours Environmental test - high temperature operation test (Optional) Digital camera (Optional) Resolution (Optional) Gray (Optional) White Balance (Optional) Color reproduction (Optional) Exposure control (Optional) Uniformity of imaging (Optional) JB/T Section Section JB/T Section 4.2 Section 5.2 JB/T Section Section JB/T Section Section JB/T Section Section JB/T Section Section JB/T Section Section JB/T Section Section After being powered for 2hs without packaging, all functions and operations shall be normal under a constant temperature of 40 and a humidity of 80%. The functions shall be in line with that are described on product. Center field shall be not less than 90% No, and the edge field shall be not less than 80% No, in which, No is the highest resolution achievable theoretically by the digital camera. Effective Numberof Pixels Image area Unit: line pairs/mm It shall be able to distinguish 10 different gray levels from black to white on gray level board. Appropriate color shall be guaranteed to be achievable under sunny, cloudy, incandescent, fluorescent, flash light and other conditions of light source. Under conditions of a variety of color temperature, error of color reproduction for the black and white target shall not exceed ± 20%. It shall be able to reproduce the color accurately, error of reproduction for three primary colors Ro, Go, Bo for each band on color standard board by the digital camera shall not exceed 120%. According to camera's sensitivity under different illumination conditions, error of exposure of the digital camera shall not exceed ± 0.5Ev. Uniformity of imaging: standard deviation of L(brightness) and three colors of R, G, B on image plane of uniform target shall not exceed 5, in which Defects on electronic image sensor (Optional) Distortion (Optional) JB/T Section Section JB/T Section Section (X is average of L, R, G and B on the whole image plane) Electronic image sensors may not have obvious defects, and two adjacent defects points on the recorded image shall not be allowed, and number of defects shall not exceed 0.002% of the total number. Relative distortion, q shall be less than 5%. Image storage JB/T The stored number of sheets described for the camera shall 71

72 characteristics (Optional) Optical viewfinder Field (Optional) Section Section JB/T Section Section be achievable in shoot of a variety of standard images. Viewfinder field shall be fully included in the actual shots screen; all sides of viewfinder field shall be more than 75% of each side of actual screen. Oxyopter of the viewfinder shall be in the range of 0 to -2 diopter (D or m-'). Optical viewfinder - other (Optional) JB/T Section Section GB Section 4.4 Viewfinder field shall not exceed the actual shot frame. when the photographic distance is 2.5m (if there is no 2.5m scale, scale slightly larger than 2.5m shall be used; when the closest photographic distance is more than 2.5m, the said closest photography distance shall be used), the percent of all sides of viewfinder field to relevant sides of actual shot frame shall be as follows: a) For single-lens and reflex camera, it shall be greater than 90%; b) For other camera, it shall be greater than 75%. It shall be with no obvious reflection, reversed image and other defects inside the viewfinder. The image shall be bright, clear and easy to read. LCD viewfinder Field (Optional) JB/T Section Section Display symbols for various functions inside the viewfinder shall be correct, clear and understandable. Its action shall be reliable, and the continuous movement shall be in coordination. Field of LCD viewfinder shall be fully included in the actual shot screen, and all sides of viewfinder field shall be more than 95% of each side of actual screen. The image display shall be clear, complete and stable. White or black defects in the screen shall not be adjacent, and shall meet the following requirements: LCD viewfinder defects (Optional) LCD viewfinder - dynamic response (Optional) LCD viewfinder- others (Optional) LCD viewfinder - brightness of active LCD viewfinder (Optional) Vibration (Optional) Durability (Optional) Built-in flashlight Electrical performance - electrical properties of the flashlight. (Optional) JB/T Section Section JB/T Section Section JB/T Section Section JB/T Section Section JB/T Section Section JB/T JB/T Section 4.7 Section JB/T JB/T JB/T Section 4.5 Section 5.5 Section Item Area 1 0 Total defects Black point White point Total defects It shall not be with obvious delays by visual check. LCD viewfinder shall be able to display the choice of operation menu and parameters settings. Centre brightness shall reach 100cd/ m 2. Visual inspection and performance test shall be performed for the sample in accordance with the requirements in JB/T Storage durability: 1000 times Flash endurance: 2,500 times Start/stop of switch: 2500 times. Shutter: times. LCD display: 2000 times Moving parts: times. Mode selector switch: times. According to JB/T Performance of built-in flash lamp relates to status and model of battery. This technical requirement is developed for the case of using alkali and high-capacity zinc manganese battery (20 ± 2, new battery with a short-circuit current of more than 3A). 1 Flash Index 72

73 JB/T Section JB /T Nominal flash index for built-in flashlight shall be not less than the results of minimum F number of the camera multiplied by 2m. If the minimum F number is greater than or equal to 5, the nominal flash index shall be not less than Limit of deviation between actual value and nominal value shall be within ± 0.8EV. 2 Effective exposure angle 2.1 Actual value shall be not less than view field angle of lens of the camera. 2.2 Limit of deviation between average of actual measured light output and actual measured light output in center point in two angles in horizontal and vertical shall be ± 1EV. 3 Response time 3.1 manual shall include nominal value of response time. 3.2 The actual value shall not exceed 1.3 times of the nominal value. 4 Preparation index In case of preparation indication being displayed, deviation between actual measured preparation index and nominal value of flash index shall be not more than ± 1.3EV. 5 Flash times for each group of batteries The actual value shall not exceed 0.8 times of the nominal value. 5.1 In case of using LR6 alkali battery: A, Nominal value shall be not less than 120 times; B, In case of nominal value being less than the specified value or in case of without a nominal value, the minimum nominal value requirements shall be in compliance. 5.2 In case of using high capacity R6 zinc-manganese batteries: A, Nominal value shall be not less than 45 times; B, In case of nominal value being less than the specified value or in case of without a nominal value, the minimum nominal value requirements shall be in compliance. 6 Durability and missing rate in flash Continuous flash times shall be not less than 500, and the missing rate shall not exceed 1%. After 300 times of flash durability test, the flash index shall be consistent with the requirements in Article Vibration resistance performance After the vibration test, the effective illumination angle of flashlight shall be consistent with the requirements in Article Resistance to high and low temperature After the resistance to high and low temperature test, the functions of flashlight shall be normal, and flash index shall meet the requirements in Article 1.2 after 1h of restoration. 9 Safety performance Any of the following phenomena shall not occur during test or use of the flashlight. A. Smoke or burning; B. Explosion of flashlight, or damage of enclosure or parts falling because of breakdown of capacitor in flashlight. 10 Appearance Appearance of flashlight shall be clean and without obvious scratches and flaws in injection. 73

74 Battery life (Optional) Electrical performance (Optional) Electrical performance - interface interchangeability (Optional) Chinese operation interface (Optional) Free fall (Optional) Children Safety Test JB/T Section 4.8 Section 5.8 JB/T Section Section JB/T Section Section 5.10 JB/T Section Section 5.11 ASTM F963-96a (mod.) JB/T Section 4.6.6, JB/T / Instruction Use and Abuse GB6675 / Hardware The shot number of sheets expressively described for the camera shall be achievable by the required new battery. For digital cameras and accessories, if any AC power is used, parts in contact with human body shall be without incorrect actions below 10kV and without damage below 13kV. All interfaces to common external parts shall comply with the relevant standard, and the interchangeability shall be very good. Operation software shall have Chinese interface, and manuals and other written materials in contact with users shall also have Chinese option. 1) No Damage 2) No non-function after reassembly No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges Visual inspection and performance test shall be performed for the sample in accordance with the requirements in JB/T

75 Mouse TEST DESCRIPTION Physical Connection mode - Interface Connection mode connecting cable Performance - function (if claim) Performance - Environmental Adaptability - Climate environmental adaptation of mouse TEST METHOD* SJT Section 6.3 SJT Section SJT Section 6.11 SJT Section GB/T 2421 GB/T 2422 GB/T GB/T GB/T MATERIAL/ COMPONENTS Mouse interface shall be serial, USB, PS / 2 and other types of interfaces. Serial interface shall meet the requirements in GB/T USB, PS/2 and other types of interfaces shall conform to the requirements stipulated in relevant national standards. (Document Review) Types of connecting cable between mouse and host can be wired or wireless. The specific requirements of cable for wired mouse shall be in accordance with relevant standards. The signal launch angle, distance, frequency and other indicators for wireless mouse shall meet the requirements in relevant standards and be described in product standards. (Document Review) It shall have its corresponding functions, and the specific functions shall comply with the relevant requirements in product standards. Details refer to See Table 1 Level 1 Requirement. Performance - free fall SJT Drop height for the non-packed mouse shall not be less than Section mm. After the drop test, it shall work properly as well. Performance - Special environmental conditions (if claim) SJT It shall be specified in standard of mouse product. The requirements shall be in accordance with GB4943 Performance Safety SJT (safety of information technology equipment (including (Optional) Section 6.12 electrical utility and equipment). Performance - Environmental Adaptability - Mechanical environmental adaptability (optional) Performance resolution (optional) Performance - resolution(optional) Performance - Resolution accuracy (optional) Performance - deviation(optional) Performance - switch life (optional) Performance travel (optional) Performance - click pressure(optional) Performance tracking speed (optional) Performance - Power adaptability (optional) Performance - Electromagnetic compatibility - radio disturbance limits SJT Section GB/T SJT Section SJT Section 6.4 SJT Section 6.5 SJT Section 6.6 SJT Section 6.7 SJT Section 6.8 SJT Section 6.9 SJT Section 6.10 SJT Section GB 9254 SJT Section GB/T Refer to See Table 2, 3, 4, 5 Unit of resolution of mouse is dpi, e.g. dots within a length of every 25.4mm, which shall be specifically regulated in product standards for mouse. Unit of resolution of mouse is dpi, e.g. dots within a length of every 25.4mm, which shall be specifically regulated in product standards for mouse. resolution accuracy shall be greater than 85%. Deviation shall not exceed 10%. Key switch life shall be more than 10 6 times. Travel of mouse shall be more than 250km. Pressure of left and right click shall be 0.3N-1.1N, and if any other keys exist, their pressure shall be specifically defined in product standards. Maximum tracking speed shall be not less than 100mm/s. It shall be able to work normally under conditions of ± 5% of nominal DC voltage range. Radio disturbance limits shall comply with the requirements in GB Radio disturbance limits for class A or B shall be clearly defined in mouse product standard. 75

76 (optional) Performance Reliability (optional) Children Safety Test SJT Section 6.15 Use and Abuse GB6675 / Hardware Mean Time Between Failures (MTBF) shall be used to measure the reliability of this product. Mouse's m1 (unacceptable value of MTBF) shall not be less than h. No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges Remarks Temperature Relative humidity Test item Initial and final vibration response test. Durability test at constant frequency Table 1 Environmental climatic adaptability Climatic conditions Level Working 10 ~35 0 ~40-10 ~55 Storage and transportation -40~5 Working 40%~80% 40%~90% 20%~93%(40 ) Storage and transportation 93%(40 ) Atmospheric pressure 86KPa~106KPa Table 2 Vibration adaptability Test content Level Frequency range Hz 5~35 10~55 10~58 58~150 Sweep speed oct/min 1 Displacement amplitude or acceleration 0.15mm 20m/s 2 Displacement amplitude or acceleration 0.15m 0.75mm(10Hz~25Hz) 0.15mm(25Hz~58Hz) 20m/s 2 Duration min 10±0.5 30±1 Table 2(continued) Test item Test content Level Frequency range Hz 5~35~5 10~55~10 10~58 58~150 Sweep frequency Displacement amplitude or acceleration 0.15mm 20m/s 2 durability test Sweep speed oct/min 1 Cycles 2 5 Note: Displacementamplitude in this able is of peak value. Table 3 Impact adaptability Level peak acceleration m/s 2 pulse duration ms Shock waveform Note: Specific impacting waveform shall be provided in product standard. 11 Half sine wave or sawtooth wave or trapezoidal wave after peak Table 4 Collision adaptability Level peak acceleration m/s 2 pulse duration ms Collision times Collision waveform Half-sine Note: The environmental adaptability grading specified in Table 1 to Table 4 shall be used in cross-selection, that is, different levels can be selected for a same product in Table 1 to Table 4. Table 5 Dropping adaptability Weight of packages(kg) Dropping height (mm) >15~ >30~

77 Portable Fan TEST DESCRIPTION Physical TEST METHOD* Drop Test GB6675 Children Safety Test MATERIAL/ COMPONENTS Use and Abuse GB6675 / Hardware 1) No Damage 2) No non-function after re-assembly No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 77

78 Plug-in Headphone/ Plug-in Speaker TEST DESCRIPTION Labeling Marking Physical Clamping force of head rings TEST METHOD* GB/T Section 6.1 GB/T Section GB 6832 Section 4.17 MATERIAL/ COMPONENTS must include: - Trademark of the manufacturer - L, R marking for stereo earphone Clamping force of head rings shall be not more than 5N. Pure tone hearing test (for headset only) (Optional) Electro-acoustic performance - rated impedance (for headset only) (Optional) Electro-acoustic performance - characteristic voltage (for headset only) (Optional) Electro-acoustic performance - Maximum noise voltage (for headset only) (Optional) Acoustic performance - frequency response (for headset only) (Optional) Electro-acoustic performance - characteristic sound pressure sensitivity (for headset only) (Optional) Electro-acoustic performance - difference between frequency responses of two earphones of the headphone. (for headset only) (Optional) GB/T Section GB/T Section GB 6832 Section GB/T Section GB 6832 Section GB/T Section GB 6832 Section GB/T Section GB 6832 Section GB/T Section GB 6832 Section 4.10 GB/T Section GB 6832 Section Required sine signal of unit power in accordance with products business standard within the rated frequency range shall be fed to the headphones (in which, power of hearing shall be not less than the maximum noise power of 1/20), and the headphone shall not have garbage sound, touching sound and abnormal sound that affects the normal use of the product. For any frequency within the rated frequency range and any control position adapting to users (if any), the impedance value shall not be less than 80% of the rated impedance. The rated impedance of headphones shown in voltage (static piezoelectricity and electret headphones) shall be the matching values that shall meet the requirements for playback of normal language and music. The preferred value of the rated impedance of headphones shown in impedance (such as moving-coil headphones) shall be 8, 32, 200, 600, 1000 and 2000Ω. Headphones shown in voltage: 2.5V Headphones shown in impedance: 5V. Headphones shown in voltage: U 5V Headphones shown in impedance: Where: U - maximum noise voltage, V; Z - rated impedance of headphones, Ω; series resistance at input end of the headphones Ω. Frequency response curves and tolerance for headphones shall conform to the requirements in the product standards. Maximum allowable deviation specified in the product standard is ± 3dB For the frequency response curves of two earphones of the stereo headphone, the difference between the average sound pressure levels in each corresponding octave bandwidth (its center frequency is in the range of Hz) shall be not more than 3dB. 78

79 Electro-acoustic performance - Total harmonic distortion (for headset only) (Optional) Environmental testing requirements and test method - hightemperature test (for headset only) (Optional) Environmental testing requirements and test method steady-state damp heat test (for headset only) (Optional) Environmental testing requirements and test method - lowtemperature test (for headset only) (Optional) Vibration (sine) test (for headset only) (Optional) Impact test (for headset only) (Optional) GB/T Section GB 6832 Section 4.11 GB/T Section GB GB/T Section GB GB/T Section GB GB/T Section GB GB section 3 GB/T Section GB section 3 The harmonic distortion under sound pressure level of 94dB in frequency range of Hz shall be (taken 20μPa as the benchmark) not more than 1%; and the harmonic distortion under sound pressure level of 94dB shall be (taken 20μPa as the benchmark) not more than 3%. After another 2h of recovery under normal atmospheric conditions following a high-temperature test at 55±2 for 2h, the headphones shall conform to the requirements in Standard (appearance and mechanical quality) and Standard 4.5 (pure tone hearing test). After another 2h of recovery under normal atmospheric conditions following a high-temperature test at 40±2, a relative humidity of 93 +2/-3% for 48h, the headphones shall conform to the requirements in Standard (appearance and mechanical quality) and Standard 4.5 (pure tone hearing test). After another 2h of recovery under normal atmospheric conditions following a low-temperature test at -25±2 for 2h, the headphones shall conform to the requirements in Standard (appearance and mechanical quality) and Standard 4.5 (pure tone hearing test). Vibration test for headphones shall conform to the requirements in Table 2, and after the test, the headphones shall conform to the requirements in Standard (appearance and mechanical quality) and Standard 4.5 (pure tone hearing test). Impact test for headphones shall conform to the requirements in Table 3, and after the test, the headphones shall conform to the requirements in Standard (appearance and mechanical quality) and Standard 4.5 (pure tone hearing test). Drop test (for headset only) (Optional) GB/T Section GB section 3 1) No Damage 2) No non-function after re-assembly Life test of head ring (if requirement and method is claimed) (for headset only) (Optional) Children Safety Test GB/T Section 4.10 Use and Abuse GB6675 / Hardware Technical requirements and test method for life test of head rings shall be provided by the enterprise s product standards No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 79

80 Torch TEST DESCRIPTION Physical Conductivity performance TEST METHOD* QB/T Section 4.2, 5.2 MATERIAL/ COMPONENTS Conductivity performance shall be good, firm in contact, without permanent enlightening, non-enlightening, flickers and other phenomena. Torch s surface shall not have breaks, obvious burrs, uneven incisions and other defects that can cause personal insecurity. Plating shall be coated firmly, smooth and bright in surface, without obvious rusts and scars, whitens, coats lost, burn marks, spots, bubbles and minor abrasions. Phenomenon Inside body of iron torch shall have a protective layer. Glass used in product shall not have molds, bruises, clear streaks, bubbles and other phenomena. Figures and words of trademark shall be clear and shall be in correct position Workmanship QB/T Section 4.7, 5.6, 5.8, 5.9, 5.10 Reflective surface of reflector shall be bright, without discoloration, trapping putty, whitening points and obvious scratches, pocking mark and other phenomena. Plastic torch: Surface of plastic pieces shall be smooth, uniform in color, without color error and paste stains and pull threads. Aluminum torch: a. Oxide stains shall be firm, smooth and wearable in surface, bright and uniform in color, no obvious color errors, good in texture; b. Inside of shaft shall be clean and smooth, and shall not have acids or bases left in oxidation staining. Positions, such as switch hole and placing spring shall not have oxide film. Switching performance Fatigue strength of three level switches QB/T Section 4.3.1, QB/T Section 4.3.2, Crystal and granular surface of tin coated product: a. Crystal and granular pattern shall be clear, white and bright. Tin scar and severe abrasions shall not be allowable. b. Paint layer shall be uniform, bright and smooth; Paint film shall not be with any dense dirty spots and paint flowing. It shall have good switching device, with an appropriate elasticity and good performance, while switch seat shall be firm in pushing actions. Switch shall be divided into three types: a. 1 st level switch, which shall be non-enlightened in no push or no press down of the keys, and shall be permanently enlightened in push or press down of the keys; b. 2 nd level switch, which shall be enlightened in press down of the keys, and shall be permanently enlightened in push up of the 1 st level switch; c. 3 rd level switch, which shall be non-enlightened in no press down of the keys before push up of the switch, and shall be enlightened in press down of the keys after push up of the 1 st level switch, and shall be permanently enlightened in push up of the 2 nd level switch. The switches shall meet the requirements in Article 4.3.1c after 3000 operation cycles (torch with a specification under 100m shall not be tested.) 80

81 Insulation Thread connection in main structure Thickness of oxide film of aluminum torch (Optional) Spotlight performance (Optional) Children Safety Test QB/T Section 4.4, QB/T Section 4.5, 5.5 QB/T Section 4.6, 5.7 GB 5945 QB/T Section 4.1, 5.1 Use and Abuse GB6675 / Hardware Insulation resistance of switch shall be not less than 0.03MΩ. Insulation resistance of bulb casing block shall be not less than 0.015MΩ. Thread in main structure shall be able to withstand a pull strength of not less than 100N (tensile test shall not be performed for thread with a specification under 100m). Thickness of oxide film of aluminum torch shall not be less than 6µm. Condenser performance shall meet the requirements in Table 1. No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 81

82 2.2.4 Bags Handbags/Backpack/Knapsack TEST DESCRIPTION Colorfastness Crocking Physical TEST METHOD* QB/T 1333 GB/T 3920 (For Textile) QB/T 2537 (For Leather) Workmanship QB/T Seam Strength QB/T Salt Spray Test QB/T QB/T 3826: Salt Spray MATERIAL/ COMPONENTS Textiles/Leather (Except White Color and non-dyed material) PU / PVC / Fabric / Leather (Sheep & Lamb Skin) Hardware Dry: Minimum 4.0 Wet: Minimum 3.0 The at least meets the PASS GRADE requirement. Details refer to Remark Table 1 Minimum 196N (44 Pounds) (For Outer) Corrosion area <= 1mm² No losing of shoulder strip, back strip and hook; Not breaking of body; straps should not have over 30% distortion Double handles : 400 cycles Handle integrity QB/T Manual Function and Cycling of Hardware QB/T Hardware Zipper Durability QB/T Functional Zipper Children Safety Test Use and Abuse GB6675 / Hardware Labeling for China Market Certificate/ Hangtags QB/T / QB/T Single handle : 250 cycles Shoulder Strap : 150 cycles Longest size of Loading Length/Width/Height (mm) <180 1kg (2.2lbs) kgs (6.6lbs) kgs (11lbs) kgs (15.5lbs) >500 10kgs (22lbs) After 200 cycles: No obvious change of Accessories After 200 cycles (PASS GRADE) No Losing and Staggering of Tooth, No Breaking of Zipper No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges Kate Spade 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Color 6. Country of Origin 7. ion Date (Month & Year) 8. Materials 9. Standard 10. Quality Grade 11. Certificate (Inspection Logo) 12. Name & Address of Manufacturer / Distributor 13. Notes for Use and Storage Conditions if necessary 82

83 Remarks Table 1 Quality requirements for appearance Requirements Excellent product product Serial Items to be tested No. 1 Overall appearance Full and plumb in style, fluent in lines, closely and straight in paste, symmetrical and correct in corners, neat and clean in whole appearance. 2 Main Fabric Leather Artificial leather, and synthetic leather Textile fabric Uniform in thickness, no crazing of leather, grain crack, decoloration and other defective phenomenon. Surface shall be smooth and straight, and without breakage in large surface in back and front, and no obvious tracks and creases shall be allowed. Without any tracks, bumps and knots. Without any broken warp and broken weft, and with no floating threads, skipped stitches, tracks, stains and flaws. Full and plumb in style, fluent in lines, closely and straight in paste, symmetrical and correct by and large in corners, neat and clean in whole appearance. Uniform in thickness, no cleaves in surface and no crazing of leather, grain crack, decoloration and other defective phenomenon. Surface shall be smooth and straight, allowing 2 coarse stains in large surface in back and front which is less than 9mm2, and allowing 2 obscure tracks and creases. Without any obvious tracks, bumps and knots. Main body without any broken warp and broken weft, and with no floating threads, skipped stitches, obvious tracks and stains.; and allowing 2 obscure tracks and stains are allowed in minor parts 3 Lining Fabric Shall be smooth and straight,neat and clean, no crazing, broken warp and broken weft, and with no floating threads, skipped stitches etc. 4 Seam Seam shall conform to the fabrics and lining, with its quality, color adapting to the surrounding parts. 5 Seam track Needle distance shall be uniform and straight, and it shall be in line between upper and lower thread track. Surface of bags shall not have empty needle, lost needle, skipping stitch, and shall not have skews in thread track. Needle distance shall be uniform and straight, and it shall be in line between upper and lower thread track. Large front surface and front cover of bags shall not have empty needle, lost needle and skipping stitches. Track skew over 15mm shall not be allowed. Empty needles, drop needle and lost stitches on each single product shall be not more than one, with the empty needles, lost stitches and skipping stitches being not more than 2 needles. 6 Zipper No teeth dislocation, no teeth missing, smooth and straight in stitches, uniform in edge distance, smooth and free in pulling together; no any color losing 7 Accessories The surface is smooth and bright, with no rust, no burrs, no pinholes, and no blistering, no peeling, no shedding and obvious scratches. The surface is smooth and bright, with no rust, no burrs, and no peeling, no shedding and other phenomenon. 8 Mounting accessories Smooth, straight and firm. 9 Standard samples * samples must be attached to the bag back with exactly the same subject material. Remark: * Inspect on handbag contains standard sample only, would not inspect if no standard sample. 83

84 Small Leather Goods / Wallets TEST DESCRIPTION Colorfastness Crocking Physical Workmanship Manual Function and Cycling of Hardware Zipper Durability Children Safety Test Use and Abuse GB6675 / Hardware Labeling for China Market Certificate/ Hangtags Remarks TEST METHOD* GB/T GB/T 2537 (For Leather) GB/T 3920 (For Textiles) QB/T GB/T GB/T QB/T / QB/T MATERIAL / COMPONENTS Textiles/Leather (Except White Color and non-dyed material) Hardware Functional Zipper Dry: Minimum 4.0 Wet: Minimum 3.0 The at least meets the PASS GRADE requirement. Details refer to Remark Table cycles: No breakage and No non-functional Zipper: 200 cycles: Shall Provide No Problem In Repeated Use Test No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Color 6. Country of Origin 7. ion Date (Month & Year) 8. Materials 9. Standard 10. Quality Grade 11. Certificate (Inspection Logo) 12. Name & Address of Manufacturer / Distributor 13. Notes for Use and Storage Conditions if necessary Table 1 Requirements for appearance quality and seams Item Excellent PASS Overall appearance neat and clean in whole appearance. Fabric leather Straight and smooth in surface, uniform in thickness, no peeling, no crazing of leather and grain crack. It is without creases, cuts, and other defects. Without fading. Leather, synthetic leather Textile fabric Inner body, compartment Bag sides Metal fittings Zipper Quality of adhesive bonding Stitch length Side distance in seam Stitch Full and plumb in style, fluent in lines, closely and straight in paste, symmetrical in corners, Straight and smooth in surface, uniform in thickness, no peeling, no crazing of leather and grain crack. It is without serious creases, cuts, and defects with an area smaller than 2mm sq in outside material shall not be allowed. Without fading. Straight and smooth in surface, without any Straight and smooth in surface, without any bumps, knots and tracks. obvious bumps, knots and tracks. Smooth in surface, without broken warp and Smooth in surface, without broken warp and broken weft, and without floating thread and broken weft, and without floating thread. 2 any defect. unobvious defects are allowed. The arrangement shall be straight and smooth and tidy. Straight, smooth and tidy, uniform in width and length. Square corner shall have no raise and no expose. Round and right in corner circle, with evenly in tuck flowers. No rust, no glitches, uniform coating, no No rust, no glitches, uniform coating, with scratches. Firm and correct in installation. slight scratches on its backside. Firm and correct in installation. No teeth dislocation, no teeth missing, smooth and straight in stitches, uniform in edge distance, smooth and free in pulling together. Firm in adhesive bonding, without loosening. (6 to 14) needles / 30 mm 1.5 mm to 3 mm (excluding decorative line) Straight, uniform, consistent in elasticity, no Straight, uniform, consistent in elasticity, no skew. No lost needle, skipping stitches, obvious skewness. No lost needle, skipping float, double needles, no lost seam at folding stitches, float, double needles, no lost seam sides. at folding sides. 84

85 2.2.5 Home s Bed Sheet / Pillow Case Bed Sheet TEST DESCRIPTION Fiber Content Fiber Content Care Label Care Label Verification Colorfastness TEST METHOD* GB/T22797 GB/T22797 MATERIAL/ COMPONENTS Comply with FZ/T Single Fiber: no tolerance 2. Blends >15%: +/-5% Blends 15%: +/-30% of the claimed fiber Shrinkage Machine wash: +/-5% Shrinkage Dry clean: Pillow case: +/-5% Crocking GB GB/T 3920 Dry: Minimum 3.0 Wet: Minimum 2.5 Perspiration GB GB/T 3922 Color Change: Minimum 3.0 Color Stain: Minimum: 3.0 Washing GB/T 3921 Water Light Physical Construction / Workmanship review Tensile Strength Children Safety Test GB GB/T 5713 GB/T 8427 Method 3 GB/T GB/T Textles Color Change: Minimum 3.0 Color Stain: Minimum: 3.0 Textiles/Leather /PVC / PU Minimum 3.0 Textile Use and Abuse GB6675 Labeling for China Market Permanent Label GB Certificate/ Hangtags Remarks GB Color Change: Minimum 3.0 Color Stain: Minimum: 3.0 The at least meets the PASS GRADE requirement. Details refer to Remark Table 1 & Appendix 1 Minimum 220N (48 Pounds) No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 1. Fiber Content 2. Sizes 3. Care Instruction 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Country of Origin 6. Materials (Fiber Content) 7. Care Instruction 8. Standard 9. Quality Grade 10. Category A, B or C 11. Certificate (Inspection Logo) 12. Name & Address of Manufacturer / Distributor 13. Notes for Use and Storage Conditions if necessary 85

86 Table 1 Items to be checked Excellent First-class Size deviation/% Skew in weft and in italic 1% Color difference and paint stains Defects in appearance Breakage and pinhole Not llowed Not allowed Breakage is not allowed, and any hole with an length of less than 20cm. Dirty and color stains Not allowed Notallowed 3 minor lots/pieces are Linear defect Not llowed 1 minor spot/piece is allowed. Strip- and block-like Not allowed 1 minor spot/piece is defects allowed. Bad printing Not allowed Slight mixing, sticking and bleeding of color, and missing of printing, without affecting the appearance. Pattern quality It is straight and correct for It is not straight and correct the pattern by and large and for the pattern, with skew not without any skew. over 3cm for large parts and Seam quality Sewing quality Embroidery quality Without skipping stitches, float, lost stitches, skew stitches, and without missing off thread. not over 2cm for small parts. Without skipping stitches, float, lost stitches, without missing off thread; with skew stitches not over 0.5cm/20cm. allowed. 1 obvious spot/piece is allowed. 1 obvious spot/piece is allowed. Not affecting the appearance as a whole. Not affecting the appearance as a whole. With skipping stitches, float, lost stitches not over 1 stitch/spot, and not over 3 for each single piece of product, and with skew stitches not over 0.5cm/20cm. Uniform in track, straight and firm in sew, flat and straight in side curling and seam, consistent in width, not exposing hair, correct in needle, and back stitches shall be made in sides evenly, with a needle density of 9-stitches / 3cm, with loosen corner ot being allowed. Straight and smooth in needles, flat in embroidery surface, change naturally in design patterns, neat in outline of embroidery, even and thin in stitches, smooth in pin running, natural in mixed color with full of three-dimensionality, clean and unstained in embroidery surface, smooth in embroidery, with no significant leakage of embroidery, accuracy in spray embroidered color, natural in transition, no overlapping and no dislocation. Note 1: If maximum size (in length or width)> 100cm, it shall be seen as a big product, if it is 100cm, it shall be seen as a small product. Note 2: Instructions for appearance and extent of defects refer to Annex A. Appendix 1 Instructions for appearance and extent of defects A.1 Linear defects: all types of defects not more than 0.2cm in width and extending in warp or weft. A.2 Strip and block defects: defects over 0.2cm in width and extending in warp or weft, but color stains and blots excluded. A.3 Breakage: holes with 2 or more of adjacent broken yarn or thread; or skipping stitches with a distance of 0.3cm or more. A.4 For minor defects and significance level, please see Annex A. Defects Level description Printing and With reference to GB/T250 Grey sample card for assessing change in color, in which Level 3-4 or above shall be seen as dyeing minor, below Level 3-4 shall be seen as obvious. defects Yarn and weaving defects Linear Minor Heavy ends not more than 3 times of a single yarn count in coarseness, interlocking of thread, reeding marks with 1-2 yarns missing, and heavy picks not more than 3 times of a single yarn count, double picks, linear missing picks and necked yarns, etc. Strip and block defects obvious Minor obvious Heavy ends more than 3 times of a single yarn count in coarseness, saw-like interlocking of thread, cracked ends and skipping of thread, reeding marks with over 2 yarns missing, and heavy picks more than 3 times of a single yarn count in coarseness, necked yarns, sloughed filling, saw -like missing picks, multi-thread of more than 3 thread, dyed yarns, oily yarns, and soiled yarns, etc. Debris woven, unevenness in trunk, corrugated by shrinking, inconsistent in stitches that is difficult to find in folding, crease not fuzzing. Parallel skipping in stitches, debris woven that can affect the appearance significantly, unevenness in trunk, inconsistent in stitches that is difficult to find in folding, not fuzzing at folding track, corrugation by shrinking, reeding and needle mark of 0.2cm in width, etc. 86

87 Pillow Case TEST DESCRIPTION Fiber Content Fiber Content Care Label TEST METHOD* GB/T22843 MATERIAL/ COMPONENTS Comply with FZ/T Single Fiber: no tolerance 2. Blends >15%: +/-5% Blends 15%: +/-30% of the claimed fiber Care Label Verification Colorfastness Crocking Perspiration Washing Water Light Dry Cleaning Physical Construction / Workmanship review Tensile Strength Children Safety Test GB/T22843 GB GB/T 3920 GB GB/T 3922 GB/T 3921 GB GB/T 5713 GB/T 8427 Method 3 GB/T GB/T 5711 GB/T GB/T Textles Textiles/Leather /PVC / PU Shrinkage Machine wash: +/-5% Shrinkage Dry clean: Pillow case: +/-5% Dry: Minimum 3.0 Wet: Minimum 2.5 Color Change: Minimum 3.0 Color Stain: Minimum: 3.0 Color Change: Minimum 3.0 Color Stain: Minimum: 3.0 Color Change: Minimum 3.0 Color Stain: Minimum: 3.0 Minimum 3.0 Textiles Color Change: Minimum 3.0 Color Stain: Minimum: 3.0 Textile Use and Abuse GB6675 Labeling for China Market Permanent Label GB Certificate/ Hangtags Remark GB The at least meets the PASS GRADE requirement. Details refer to Remark Table 1 & Appendix 1 Minimum 220N (48 Pounds) No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 1. Fiber Content 2. Sizes 3. Care Instruction 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Country of Origin 6. Materials (Fiber Content) 7. Care Instruction 8. Standard 9. Quality Grade 10. Category A, B or C 11. Certificate (Inspection Logo) 12. Name & Address of Manufacturer / Distributor 13. Notes for Use and Storage Conditions if necessary Serial No. Table 1 Items to be checked Excellent First-class 87

88 1 Size deviation/ ±1.5 ±2.5 ±3.5 1% 2 Skew in weft and in italic 1% Color difference and paint stains Defects in appearance Breakae and pinhole Not allowed Not allowed Breakage is not allowd, and pinhole with an length of ess than 20cm Dirty and Not allowed Not allowed 3 minor spots/pices are allowed. color stains Linear Not allowed 1 minor spot/piece is 1 obvious spot/piece is allowed. defcts allowed. Strip- and block-like defects Not allowed 1 minor spot/piece is allowed. 1 obvious spot/piece is allowed. Bad printing Not allowed Slight mixing, sticking and bleeding of color, and missing of printing, without affecting the appearance. 5 Pattern quality It is straight and correct for the pattern by and large and without any skew. 6 Seam quality Sewing stitches Quilting stitches Without skipping stitches, float, lost stitches, skew stitches, and without missing off thread. It is not straight and correct for the pattern, with skew not over 3cm for large parts and not over 2cm for small parts. Without skipping stitches, float, lost stitches, without missing off thread, with skew stitches not over 0.5cm/20cm. Not affecting the appearance as a whole. Not affecting the appearance as a whole. With skipping stitches, float, lost stitches, missing stitches not over 1 stitch/spot, and not over 3 in total for each single piece of product, and with skew stitches not over 0.5cm/20cm. With skipping stitches, float, lost stitches, missing stitches not over 1cm/spot, and not over 5/piece in total. 7 Quality of quilting Smooth and flat in stitch track, no wrinkle in fabric, back stitches made at beginning and end of quilting, accurate in connection of needles, no thread taking out, uniform and tidy in the same needle track. 8 Sewing quality Uniform in track, straight and firm in sew, flat and straight in side curling and seam, consistent in width, not exposing hair, dislocation in seaming of outside or inside material less than 1cm, correct in needle, and back stitches shall be made in sides evenly, with a needle density 10 stitches / 3cm for normal sewing, and 9 stitches / 3cm for over-lock seam. Note 1: For minor defects and significance level, please see Annex A. Note 2: Negative deviation shall only be examined for size of cushion for pillowcases. Note 3: If maximum size (in length or width)> 100cm, it shall be seen as a big product; if it is 100cm, it shall be seen as a small product. Note 4: Quilting needle density will not be examined. Appendix 1 Instructions for appearance and extent of defects A.1 Linear defects: all types of defects not more than 0.2cm in width and extending in warp or weft. A.2 Strip and block defects: defects over 0.2cm in width and extending in warp or weft, but color stains and blots excluded. A.3 Breakage: holes with 2 or more of adjacent broken yarn or thread; or skipping stitches with a distance of 0.3cm or more. A.4 For minor defects and significance level, please see Annex A. Defects Level description Printing and With reference to GB/T250 Grey sample card for assessing change in color, in which Level 3-4 or above shall be seen as dyeing minor, below Level 3-4 shall be seen as obvious. defects Yarn and weaving defects Linear Minor Heavy ends not more than 3 times of a single yarn count in coarseness, interlocking of thread, reeding marks with 1-2 yarns missing, and heavy picks not more than 3 times of a single yarn count, double picks, linear missing picks and necked yarns, etc. Strip and block defects obvious Minor obvious Heavy ends more than 3 times of a single yarn count in coarseness, saw-like interlocking of thread, cracked ends and skipping of thread, reeding marks with over 2 yarns missing, and heavy picks more than 3 times of a single yarn count in coarseness, necked yarns, sloughed filling, saw -like missing picks, multi-thread of more than 3 thread, dyed yarns, oily yarns, and soiled yarns, etc. Debris woven, unevenness in trunk, corrugated by shrinking, inconsistent in stitches that is difficult to find in folding, crease not fuzzing. Parallel skipping in stitches, debris woven that can affect the appearance significantly, unevenness in trunk, inconsistent in stitches that is difficult to find in folding, not fuzzing at folding track, corrugation by shrinking, reeding and needle mark of 0.2cm in width, etc. 88

89 Ceramic/Porcelain TEST DESCRIPTION Physical TEST METHOD* MATERIAL/ COMPONENTS Construction review GB/T 3532 /Hardware The at least meets the PASS GRADE requirement. Details refer to Remark Table 1 Microwave Safe (If Applicable) One (1) Cycle GB/T No breakage or electric arc From Refrigerator To Microwave Safe (If Applicable) From Refrigerator To Oven Safe (If Applicable) Water Absorbency Heat Resistance Whiteness (Optional) Glossiness of Glaze Color Deviation (Optional) Labeling for China Market One (1) Cycle GB/T No breakage or electric arc One (1) Cycle GB/T No breakage GB/T GB/T 3299 GB/T GB/T 3298 GB/T QB/T 1503 GB/T GB/T 3295 GB/T QB/T 1503 Ceramic Ceramic Ceramic Ceramic Ceramic Fine Porcelain: 0.5% Normal Porcelain: 1.0% Stoneware: 5.0% Set: No breakage after one cycle from 180 to 20 Individual: Small & middle size: No breakage after one cycle from 180 to 20 Big & supper size: No breakage after one cycle from 160 to 20 High performance: 70.0 Grade one: 60.0 : 55.0 High performance & Grade one: 85.0 : 80.0 High performance: 1.0 Grade one: 2.0 : 3.0 Certificate/ Hangtags Ceramic: GB/T 3302 Ceramic (at base of product): 1. Brand Name 2. Name of Manufactory & Region Remarks 89

90 Serial No. Table 1 Name of defects Measurement Specification Excellent product 1st grade product product Dishes Small Middle Large % of its 1.0% of its 2.0% of its Special diameter diameter diameter Height (mm) Plates < ~< ~< % of its 1.5% ofits 2.0 of its diameter diameter diameter Bowls Small Middle Large Deformation Diameter (mm) 2 Fallingslag Diameter (mm) 3 Pores Dameter (mm) 4 Spot Diameter (mm) Special 0.7% of its 1.0% of its diameter diameter Cups Small Middle Large % of its diameer Special 1.5% of its 2.0% of its diameter diameter Kettles < Small, Middle Large, Specal Small Middle Large Special Unallowable Unallowable Unallowable Unallowable It shall be unallowable for visible surface, and shall be 0.5mm in size and 2 in number for invisible surface. Unallowable for visible surface, and 0.5mm in size and 3 in number for invisible surface. It shall be unallowable for visible surface, and shall be 0.5mm in size and 2 in number for invisible surface. It shall be 1.0 mm in size and 2 in number for visible surface, and shall be 0.5mm in size and 3 in number. 0.5 in size and 2 in number 0.5 in size and 3 in number 0.5 in size and 6 in number 0.5 in size nd 7 in number 2.5% ofits diameter It shall be 1.0 mm in size an 2 in number for visible surface, and shall be 0.5mm in size and 3 in number. It shall be 1.5 mm in sze and 2 in number for visible surface, and shall be 2.0mm in size and 3 in number. 1.0 in size and 4 in number 1.0 in size nd 6 in number 1.0 in size and 8 in number 1.0 in size and 1 in nmber 1.5 in size and Small Unallowable Unallowable 2 in number Middle Unallowable 1.5 witha 90

91 Large Special 5 Color Mark Area(mm2) All types Unallowable 6 Cave Diameter (mm) 7 Stain on plaster Area (mm2) 8 Knot and bubble Diameter (mm) 9 Sludge Area (mm2) Small Middle Large Special Small Middle Large Special Small Middle Large Special Small Middle Unallowable Unallowable Unallowable Unallowable for visible surface; and 1.0 for invisible surface. Unallowable for visible surface; 0.5 with a maximum number of with a maximum number of 1. For visible surface, 3.0; for invisible surface, 0.0. Unallowable for visible surface; and shall be 1.0 with a maximum number of 1 for invisible surface. Unallowable for visible surface; and shall be 1.5 with a maximum number of 1 for invisible surface. Unallowable for visible surface; and shall be 2.0 with a maximum number of 1 for inisible surface Unallowable for visible surface; and shall be 2.0 wit a maximumnumb er of 2 fo invisible surface. Unallowable for visible surface; and 2.0 for invisible surface. Unallowable for visible surface; and 3.0 for invisble surface. Unallowable for visible surface; and 6.0 for invisible surface. Unallowable for visible surface; and 12.0 for invisible surface. 1.0 with a maximum number 0of with a maximum number of ,with a maximum number of with a maximum number o 4. maximum numer of with a maxium number of with a maximum number of 4. For visible surface, 12.0; for invisible surface, with a maximum nuber of with a maximum number of with a maximum number of with a maximum number of with a maximum number of with a maximum numer of with a maximum number of witha maximum number of

92 10 Bubble Diameter (mm) Sticky residue along bottom side Enamel Loss(including glaze pressing and glaze shrinkage) Large Special Small Middle Large Special and 2.0 for invisible surface. Unallowable for visible surface; and 4.0 for invisible surface. Unallowable for visible surface; and 8.0 for invisible surface. Unallowable Length (mm) All types Unallowable Length (mm) Area mm2 All types Unallowable , with a maximum number of , with a maximum number of , with a maximum number of , with a maximum number of 5. Unallowable along outer side, and 15% of bottom diameter along inner side, with its width 1.0 Length of glaze pressing parts shall be 2.0; length of inner bottom side 10.0, and other types of enamel loss shall be unallowable. Glaze shrinkage in bottom: for small and middle: it shall be with an area of 30, while for large and special: it shall be with an area of , with a maxmum number of 3 1.5, with a maximum number of , with a maimum number of , with a maximum number of 6. 30% of bottom diameter along outer side, and 50% of bottom diameter along inner side. Length of glaze pressing parts shall be 10.0; length of inner bottom side shall be 40.0, and other types of enamel loss parts shall be with an area of 30. Glaze shrinkage in bottom: for small and middle type: it shall be with an area of 60, while for large and special type: it shall be with an area of Crack Length (mm) Small Middle Large Unallowable Hidden cracks shall be unallowable for visible surface; and shall be 3.0 for invisible surface. Hidden cracks shall be unallowable for visible surface; and shall be 4.0 for invisible surface. Hidden cracks shall be unallowable for visible surface; and shall be 5.0 Hidden cracks shall be 6.0. Hidden cracks shall be 8.0. Hidden cracks shall be

93 14 side blisters and side gills Diameter and Length (mm) Special Small Middle Large Special Unallowable 15 Stiky scar Lengt (mm) All types Unallowable 16 sticky glaze on decoration Are (mm2) 17 Lack of mud Area (mm2) Small for invisible surface. Hidden cracks shall be unallowable for visible surface; and shall be 6.0 for invisible surface. Side blisters shall be unallowable, and side gills shall be 6.0. Side blisters shall be unallowable, and side gills shall be Side blisters shall be unallowable, and side gills shall be Side blisters shall be unallowable, and side gills shall be Sticky foot shall be 5% of bottom diameter, with a depth 0.5(mm) Hidden cracks shall be , with a length of , with a length of , with a length of , with a length of 80.0 Sticky foot shall be 20% of bottom diameter, with a depth 1.0(mm).0 Middle 10.0 Unallowable Unallowable Large 20.0 Special 30.0 Small Middl Large Special 18 Defects in line Length (mm) Al type 19 Defects in drawings Area (mm2) All types Unallowable for visible surface; and 10.0 for invisible surface. Unallowable for visible surface; and 15.0 for invisible surface. Unallowable for visible surface; and 20.0 for invisible surface. Unallowable for visible surface; and 25.0 for invisible surface. Breakage in sides, lines and in color shall be unallowable; blue color defects shall be insignificant, and color error and loss in side line shall also be insignificant. 4.0, with a maximum number of (which shall be 3.0 at its mouth.) 20.0 (which shall be 2.0 at its mouth.) 25.0 (which shall be 3.0at it mouth.) 30.0 (which shall be 3.0 at its mouth.) Length of breakage shall be 2.0 (breakage at wide color side shall be unallowable); blue color defects shall be insignificant, and color error and loss in side line shall also be insignificant. 7.0, with a maximum number of 2. (or 10.0, with a maximum 40.0 (which shall be 5.0 at its mouth.) 60.0 (which shall be 5.0 at its muth.) 80.0 (whic shall be 7.0 at its mouth.) (which shall be 7.0 at its mouth.) Length of breakage shall be 4.0, with a maximum number of 5; bue color defects and color error and loss in side line shall be not seriou. 25% ofdrawings. 93

94 number of 1.) Small Burning mark Area (mm2) Middle Unallowable Unallowable 50.0 Large Bruises in glazed surface Smoky and yellow spot Thin parts of glaze and orange spots Incorrectness in handle and ear and other parts, color difference in joints, and color error. Slips, waves of glaze and rolling marks Special All types Unallowable Unobvious -- All types Unallowable Unallowable Not serious -- All types Unallowable for visible surface; and unobvious for invisible surface. Unobvious Not serious -- All types Rather unobvious Unobvious Not serious -- All types Unallowable for visible surface; and unobvious for invisible surface. Unobvious for visible surface; and not serious for invisible surface. Not serious Converting provisions for defects mentioned above: 1 Unless expressly provided, the allowable scope of defects in this table shall be referred to that of visible surface, while the specified size of defects of invisible surface shall be increased by 50% of that of visible surface, and the pores size shall be according to the regulations, with its number being divided by 2. 2 For defects with a diameter of 50% smaller than in requirements, with its number slightly larger than required, two can be seen as one; while the absolute number of increase shall not exceed 50% of the required total number of the original level of defects (if the total number in original regulations is an odd, it can add one to the total number, which is then divided by 2). 3 If the maximum number of defects is not specified, it can be calculated by adding the number by its size. 4 For minor defects with its diameter 0.3mm, length 0.5mm and area 1mm2 and of light color and other unobvious defects in firstclass and qualified products shall not be seen as defects. 5 The number of defects within a distance of 10mm2 shall be not more than 2. 6 Defects not included i this standard shall be treated in accordance with that in similar cases. 1 Multilateral deformation shall be unallowable for excellent products; for first-class and qualified products, the extent of defects shall be decreased by 50%; rugged bottom shall be very unobvious for excellent products, and shall be unobvious for first-class and qualified products. 2 Residue falling on rim shall be unallowable for first-class products, with its size 0.5, with a maximum number of 1, and residues at others parts shall be smoothened off. 3 Special grouting products: the specified extent for first-class and qualified products shall be the same, and its number shall be increased by 1 and the pores shall not be dense. 4 Stick dirty in bottom shall not be obvious for 1st class products, and shall not be serious for qualified products. 5 Bubbles shall be smooth, and that can be significantly felt shall be unallowable. 6 It shall be suitable for the case in which it is smooth under the glaze, or it shall be tested in accordance with knots. 7 Opening bubble of glaze shall be unallowable for 1st class products, and opening bubble at mouth of qualified openings shall be unallowable. 8 Sticky residue shall be smoothened off; diameter of fish plate shall be calculated in accordance with the long diameter at bottom. 9 Width of glaze shrinkage at bottom shall be 1; glaze pressing at mouth, ear and handle in small and middle product shall be 2.0 for 1st class products, and shall be 4.0 for qualified products.j. Cracks of glaze at ear and handle and holes inside the kettle and other hidden parts shall be 2.0 for 1st class products with a maximum number of 1. It shall be 3.0 for qualified products of small and middle type, and shall be 5.0 for the same of large and special type, and cracks of glaze at ear and handle and holes inside the kettle and other hidden parts shall be 2.0, with a maximum number of Sticky scar in other parts shall be unallowable; diameter of fish plate shall be calculated according to the longer diameter at bottom foot, with the bottom foot being smoothened out. 11 Side cut shall be unallowable for qualified products. 12 Depth of lack of mud shall be 0.5 for excellent and 1st class products, and shall be 1.0 for qualified products. 13 All-over defects for 1st class and qualified products shall add one for each. Film mark shall be very unobvious for excellent products and shall be unobvious for 1st class products, and shall be not so obvious for qualified products; local light color defects shall be treated as defects in drawings. Deformities in head, hands and feet of figures, birds and beasts and in letter or symbol of ornament shall be unallowable for excellent and 1st class products, and shall be unobvious for qualified products Cushion/Pillow 94

95 TEST DESCRIPTION Fiber Content TEST METHOD* MATERIAL/ COMPONENTS Fiber Content GB/T Comply with FZ/T Single Fiber: no tolerance 2. Blends >15%: +/-5% Blends 15%: +/-30% of the claimed fiber Colorfastness Crocking GB GB/T 3920 Textiles (Except White Color and non-dyed material) Dry: Minimum 3.0 Wet: Minimum 2.5 Drycleaning GB/T 5711 Textiles Color Change: Minimum 3.0 Color Stain: Minimum 3.0 Light GB/T 8427 Textiles Minimum 3.0 Perspiration GB GB/T 3922 Textiles Color Change: Minimum 3.0 Color Stain: Minimum 3.0 Washing GB GB/T 3921 Textiles (Except White Color and non-dyed material) Color Change: Minimum 3.0 Color Stain: Minimum 3.0 Water Physical Construction / Workmanship review GB GB/T 5713 GB/T Textiles Color Change: Minimum 3.0 Color Stain: Minimum 3.0 The at least meets the PASS GRADE requirement. Details refer to Remark Table 1 & Appendix 1 Tensile Strength GB/T Textiles Minimum 220N (48 Pounds) Children Safety Test Use and Abuse GB6675 / Hardware No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges Labeling for China Market Permanent Label GB Certificate/ Hangtags GB Fiber Content 2. Sizes 3. Care Instruction 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Country of Origin 6. Materials (Fiber Content) 7. Care Instruction 8. Standard 9. Quality Grade 10. Category A, B or C 11. Certificate (Inspection Logo) 12. Name & Address of Manufacturer / Distributor 13. Notes for Use and Storage Conditions if necessary 95

96 Remark Table 1 Serial Items to be checked Excellent First-class No. 1 Size deviation/ ±1.5 ±2.5 ±3.5 1% 2 Skew in weft and in italic % 3 Color difference and paint stains Defects in appearance Breakage and pinhole Not allowed Not allowed Breakage is not allowed, and pinhole with an length ofless than 20cm Dirty and Not allowed Not allowed 3 minor spots/pieces are allowed. color stains Linear Not allowed 1 minor spot/piece is 1 obvious spot/piece is allowed. defects allowed. Strip- and block-like defects Not allowed 1 minor spot/piece is allowed. 1 obvious spot/piece is allowed. Bad printing Not allowed Slight mixing, sticking and bleeding of color, and missing of printing, without affecting the appearance. 5 Pattern quality It is straight and correct for the pattern by and large and without any skew. 6 Seam quality Sewing stitches Quilting stitches Without skipping stitches, float, lost stitches, skew stitches, and without missing off thread. It is not straight and correct for the pattern, with skew not over 3cm for large parts and not over 2cm for small parts. Without skipping stitches, float, lost stitches, without missing off thread, with skew stitches not over 0.5cm/20cm. Not affecting the appearance as a whole. Not affecting the appearance as a whole. With skipping stitches, float, lost stitches, missing stitches not over 1 stitch/spot, and not over 3 in total for each single piece of product, and with skew stitches not over 0.5cm/20cm. With skipping stitches, float, lost stitches, missing stitches not over 1cm/spot, and not over 5/piece in total. 7 Quality of quilting Smooth and flat in stitch track, no wrinkle in fabric, back stitches made at beginning and end of quilting, accurate in connection of needles, no thread taking out, uniform and tidy in the same needle track. 8 Sewing quality Uniform in track, straight and firm in sew, flat and straight in side curling and seam, consistent in width, not exposing hair, dislocation in seaming of outside or inside material less than 1cm, correct in needle, and back stitches shall be made in sides evenly, with a needle density 10 stitches / 3cm for normal sewing, and 9 stitches / 3cm for over-lock seam. Note 1: For minor defects and significance level, please see Annex A. Note 2: Negative deviation shall only be examined for size of cushion for pillowcases. Note 3: If maximum size (in length or width)> 100cm, it shall be seen as a big product; if it is 100cm, it shall be seen as a small product. Note 4: Quilting needle density will not be examined. Appendix 1 Instructions for appearance and extent of defects A.1 Linear defects: all types of defects not more than 0.2cm in width and extending in warp or weft. A.2 Strip and block defects: defects over 0.2cm in width and extending in warp or weft, but color stains and blots excluded. A.3 Breakage: holes with 2 or more of adjacent broken yarn or thread; or skipping stitches with a distance of 0.3cm or more. A.4 For minor defects and significance level, please see Annex A. Defects Printing and dyeing defects Yarn and weaving defects Level description With reference to GB/T250 Grey sample card for assessing change in color, in which Level 3-4 or above shall be seen as minor, below Level 3-4 shall be seen as obvious. Linear Minor Heavy ends not more than 3 times of a single yarn count in coarseness, interlocking of thread, reeding marks with 1-2 yarns missing, and heavy picks not more than 3 times of a single yarn count, double picks, linear missing picks and necked yarns, etc. obvious Heavy ends more than 3 times of a single yarn count in coarseness, saw-like interlocking of thread, cracked ends and skipping of thread, reeding marks with over 2 yarns missing, and heavy picks more than 3 times of a single yarn count in coarseness, necked yarns, sloughed filling, saw -like missing picks, multi-thread of more than 3 thread, dyed yarns, oily yarns, and soiled yarns, Strip and block defects Minor obvious etc. Debris woven, unevenness in trunk, corrugated by shrinking, inconsistent in stitches that is difficult to find in folding, crease not fuzzing. Parallel skipping in stitches, debris woven that can affect the appearance significantly, 96

97 unevenness in trunk, inconsistent in stitches that is difficult to find in folding, not fuzzing at folding track, corrugation by shrinking, reeding and needle mark of 0.2cm in width, etc. 97

98 Domino Set TEST DESCRIPTION Children Safety Test TEST METHOD* MATERIAL/ COMPONENTS Use and Abuse GB 6675 / Hardware 1) No Safety Hazards - No Small Parts & Sharp Points/Edges 2) Comply with the relevant regulatory REQUIREMENT Flammability Flammability (Solids) GB Comply with the regulatory REQUIREMENT Labeling for China Market Certificate/ Hangtags (for Children only) GB 6675 Comply with the regulatory REQUIREMENT Reference Photo: 98

99 Gumball Machine TEST DESCRIPTION Children Safety Test TEST METHOD* MATERIAL/ COMPONENTS Use and Abuse GB 6675 / Hardware No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges **Additional Restricted Substances (RS) Test Health Requirements (for Hygienic Standard Food Contacting Details refer to Remark 1 China market) for Foods Contacting Components * For Market Country including China, the GB testing must be conducted by China Government Approved Labs Remark Plastics (PVC) Remark 1 A List of Hygienic Standards and Test Methods for Food Contact Materials and s: Category Standards No and Name Item Requirements GB Health Standard of PVC Resin Physical and chemical Used in Food Containers indicators and Packages. Plastics (PP) Plastics (PE) Plastics (PS) GB Health Standard for Finished of PVC Used in Food Containers GB Health Standard for Finished of PVC in Food Containers GB Health Standard of Polypropylene Resin in Food Containers GB Hygienic Standard for Finished of Polypropylene in Food Cotainers GB Health Standard of Polyethene Resin in Food Containers GB Hygienic Standard for Finished of Polypropyene Food Containers GB Health Standard of Polystyrene Resin in Food Containers Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) Vinyl chloride monomer Decolorization test Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) Decolorization test Physical and chemical indicators Evaporated residues Consuptiof potassium permanganate Heavy metals (Pb) Deolorization test Physical and chemical indicators Evaporated residues Consumption of potassium permaganate Heavy metal(pb) Decolorization test Physical and chemical indicators Vinyl chloride 5mg/mg 1.2- dichloroethane 2mg/kg 1.1- dichloroethane 150mg/kg In 4% acetic acid soaked solution, 30mg/L In 20% alcohol soaked solution, 30mg/L In Hexane socked solution, 150mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1mg/L 1mg/L Soaking solution: Negative Buffet oil or colorless oil: Negative In 4% acetic acid soaked solution, 30mg/L In 65% alcohol soaked solution, 30mg/L In Hexane socked solution, 30mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1mg/L Soaking solution: Negative Buffet oil or colorless oil: Negative Ethanol: Negative Hexane extract 2% Weight loss in drying 0.15% In 4% acetic acid soaked solution, 30 mg/l In Hexane socked solution, 30mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1 mg/l Soaking solution: Negative Buffet oil or colorless oil: Negative Ethanol: Negative Weight loss in drying 0.15% Residue after ignition 0.20% In Hexane socked solution, 2.00% In 4% acetic acid soaked solution, 30 mg/l In 65% alcohol soaked solution, 30mg/L In Hexane socked solution, 30mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1 mg/l Soaking solution: Negative Buffet oil or colorless oil: Negative Ethanol: Negative Weight loss in drying 0.15% Volatile 1.0% Styrene 0.5% Ethyl benzene 0.3% Hexane extract 1.5% 99

100 Plastics (Melamine) Plastics (Perchloroethylene) Plastics (Urushiol Coatings) Plastics (Organic Silicone Antiadhesive Coatings) Plastics (Teflon Coatings) Plastics (Polyethylene Glycol Terephthalate) Plastics (Unsaturated Polyester Resin GB Health Standard for Finished of Polystyrene in Food Containers GB Health Standard for Finished of Melamine in Food Containers GB Health Standard of Inside-wall Coatings of Perchloroethylene in Food Containers GB Health Standard of Urushiol Coatings in Food Containers GB Health Standard of Organic Silicone Anti-adhesive Coatings in Food Containers. GB Health Standard of Inside-wall Teflon Coatings in Food Containers GB Health Standard of Finished of Polyethylene Glycol Terephthalate in Food Containers and as Packages Materials. GB Health Standard of Polyethylene Glycol Terephthalate Resin in Food Containers and Packages Materials. GB Health Standard of Unsaturated Polyester Resin and Its Fiberglass Reinforced Plastics s in Food Containers and Packages Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) Decolorization test Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) Decolorization test Formaldehyde Evaporated residues Consumption of potassium permanganate Lead (Pb) Arsenic (As) Residual of vinyl chloride monomer Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) Formaldehyde Free phenol Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) Evaporated residues Consumption of potassium permanganate Cr F Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) Sb Decolorization test Pb Sb Extract Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) In 4% acetic acid soaked solution, 30mg/L In 65% alcohol soaked solution, 30mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1mg/L Soaking solution: Negative Buffet oil or colorless oil: Negative Ethanol: Negative In water socked solution, 10mg/L In 65% alcohol soaked solution, 30mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1mg/L Soaking solution: Negative Buffet oil or colorless oil: Negative 65% ethanol: Negative In 4% acetic acid soaked solution, 30mg/L In 4% acetic acid soaked solution, 2,000mg/L In 65% alcohol soaked solution, 40mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1.0mg/L In 4% acetic acid soaked solution, 0.5mg/L 1mg/L In 4% acetic acid soaked solution, 30mg/L In 65% alcohol soaked solution, 30mg/L In water socked solution, 30mg/L In Hexane socked solution, 30mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1mg/L In 4% acetic acid soaked solution, 5mg/L In water socked solution, 0.1mg/L In water socked solution, 30mg/L In 4% acetic acid soaked solution, 30mg/L In Hexane socked solution, 30g/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1mg/L In water socked solution, 30mg/L In 4% acetic acid soaked solution, 60mg/L In Hexane socked solution, 30mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 0.01mg/L In water socked solution, 0.2mg/L In water socked solution, 30mg/L In 4% acetic acid soaked solution, 30mg/L In Hexane socked solution, 30mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1.0mg/L In 4% acetic acid soaked solution, 0.05mg/L Soaking solution: Negative Buffet oil or colorless oil: Negative Ethanol: Negative 1mg/kg 1.5mg/kg In water, 0.5% In 65% alcohol, 0.5%. In 4% acetic acid, 0.5%. Hexane 0.5% In 65% ethanol soaked solution, 30 mg/l In 4% acetic acid soaked solution, 30mg/L In Hexane socked solution, 30mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1.0mg/L 100

101 Plastics (Polycarbonic Ester Resin) Plastics (Polycarbonic Ester) Plastics (vinylidene chloride-vinyl chloride copolymer resins) Plastics (Nylon) Plastics (rubber modified acrylonitrile butadiene styrene) Plastics (acrylonitrilestyrene) Plastics (Rubber) Materials. GB Health Standard of Polycarbonic Ester Resin Used in Food Containers and Packaging Materials GB Health Standard of Finished of Polycarbonic Ester in Food Containers and Packaging Materials GB Hygienic standard of vinylidene chloride-vinyl chloride copolymer resins for food containers and packaging material. GB Hygienic standard of nylon 6 resins used in food packaging materials GB Hygienic standard of finished product of nylon in food packaging materials GB Hygienic standard of finished product of rubber modified acrylonitrile butadiene styrene used in food containers and packaging materials. GB Hygienic Standard of Finished of acrylonitrilestyrene in Food Containers and Packaging Materials GB Hygienic standard of rubber products for food industry Ethyl benzene compounds (calculated in styrene) Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) Phenol Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) Phenol Decolorization test Residual of vinylidene chloride monomer Residual of vinyl chloride monomer Caprolactam Caprolactam Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) Decolorization test Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) Acrylonitrile monomer Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) Acrylonitrile monomer Evaporated residues Consumption of potassium permanganate Zn Heavy metal (Pb) Residual acrylonitrile 0.1% In water socked solution, 15mg/L In 20% ethanol soaked solution, 15mg/L In 4% acetic acid soaked solution, 15mg/L In Hexane socked solution, 15mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1.0mg/L 0.05mg/L In water socked solution, 30mg/L In 20% ethanol soaked solution, 30 mg/l In 4% acetic acid soaked solution, 30mg/L In Hexane socked solution, 30mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1.0mg/L 0.5mg/L Soaking solution: Negative Buffet oil or colorless oil: Negative Ethanol: Negative 10mg/L 2mg/L 150mg/L 150mg/L In water socked solution, 30mg/L In 20% ethanol soaked solution, 30 mg/l In 4% acetic acid soaked solution, 30mg/L In Hexane socked solution, 30mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1.0mg/L Soaking solution: Negative Buffet oil or colorless oil: Negative Ethanol: Negative In water socked solution, 15mg/L In 20% ethanol soaked solution, 15mg/L In 4% acetic acid soaked solution, 15mg/L In Hexane socked solution, 15mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1.0mg/L 11mg/L In water socked solution, 15mg/L In 20% ethanol soaked solution, 15mg/L In 4% acetic acid soaked solution, 15mg/L In Hexane socked solution, 15mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1.0mg/L 50mg/L In 4% acetic acid soaked solution, 2,000mg/L In 65% alcohol soaked solution, 40mg/L In water socked solution, 30mg/L In Hexane socked solution, 2,000mg/L In water socked solution, 40mg/L In 4% acetic acid soaked solution, 20mg/L In 4% acetic acid soaked solution, 1.0mg/L 11mg/L 101

102 Aluminum articles GB Hygienic Standard for aluminum food containers Physical and chemical indicators Lead leaching 0.2 mg/l Cadmium leaching 0.02 mg/l Arsenic leaching 0.04 mg/l Zinc leaching 1 mg/l Stainless steel GB Hygienic Standard for Stainless Steel Food Containers. Heavy metal Austenitic: Lead leaching 1.0 mg/l Chromium leaching 0.5 mg/l Nickel leaching 3.0 mg/l Cadmium leaching 0.02 mg/l Arsenic leaching 0.04 mg/l Martensite: Lead leaching 1.0 mg/l Nickel leaching 1.0 mg/l Cadmium leaching 0.02 mg/l Arsenic leaching 0.04 mg/l Ceramics GB Hygienic Standard for Ceramic Food Containers Heavy metal Lead < 7mg/ dm 2 Cd < 0.5mg/ dm 2 Reference Photo: 102

103 Ice Pop Tray TEST DESCRIPTION Children Safety Test TEST METHOD* MATERIAL/ COMPONENTS Use and Abuse GB6675 / Hardware ** Additional Restricted Substances (RS) Test Health Requirements Hygienic Standard for (for China market) Foods Contacting Remark Food Contacting Components No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges Details refer to Remark 1 Remark 1 A List of Hygienic Standards and Test Methods for Food Contact Materials and s: Category Standards No and Name Item Requirements Plastics (Organic Silicone Antiadhesive Coatings) Plastics (rubber modified acrylonitrile butadiene styrene) Plastic (Rubber) GB Hygienic Standard of Organic Silicone Anti-adhesive Coatings in Food Containers. GB Hygienic standard of finished product of rubber modified acrylonitrile butadiene styrene used in food containers and packaging materials. GB Hygienic standard of rubber products for food industry Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) Evaporated residues Consumption of potassium permanganate Heavy metal (Pb) Acrylonitrile monomer Evaporated residues Consumption of potassium permanganate Zn Heavy meta (Pb Residual acrylonitrile In water socked solution, 30mg/L In 4% acetic acid soaked solution, 30mg/L In Hexane socked solution, 30g/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1mg/L In water socked solution, 15mg/L In 20% ethanol soaked solution, 15mg/L In 4% acetic acid soaked solution, 15mg/L In Hexane socked solution, 15mg/L In water socked solution, 10mg/L In 4% acetic acid soaked solution, 1.0mg/L 11mg/L In 4% acetic acid soaked solution, 2,000mg/L In 65% ethanol soaked solution, 40mg/L In water socked solution, 30mg/L In Hexane socked solution, 2,000mg/L In water socked solution, 40mg/L In 4% acetic acid soaked solution, 20mg/L In 4% acetic acid soaked solution, 1.0mg/L 11mg/L Reference Photo: 103

104 Luggage TEST DESCRIPTION Colorfastness Crocking Physical Size Review TEST METHOD* QB/T QB/T 2537 MATERIAL/ COMPONENTS Textiles/Leather (Except White Color and non-dyed material) Dry: Minimum 4.0 Wet: Minimum 3.0 QB/T & Travelling Case: If 660(26 ),+/-6mm, Others: +/-5mm Materials and Trims Review (QB/T ): QB/T ~3 QB/T ~2 Pass the Related Standards Construction Review Seam Strength Salt Spray Test QB/T QB/T (QB/T ): QB/T 3826: SALT SPRAY QB/T 3832 Details Refer Remark 1 PU / PVC / Fabric Minimum 196N (44 Pounds) Hardware Corrosive Area: Max. 2mm² Lever operability QB/T QB/T 2919 Lever can be pulled and pushed smoothly, with no distortion, no loosening after 4000 cycles Rolling Test QB/T Handle Integrity QB/T Curb Drop Test QB/T Load Capacity QB/T Flat Press QB/T Surface Hardness QB/T The test shall be performed under the specified conditions, with 8 km continuous walking test for qualified products Wheel is flexible in rotation after the test, and without obstruction and deformation; without deformation and cracking in wheel frame and wheel axis; wheel wear is not greater than 2mm at the same time. Lever can be pulled and pushed smoothly, with no distortion, no loosening, no obstruction; junction between lever and body of box is without cracking and loosing. Additional 5kg loading should be added at connecting position for double lever style No losing; Not breaking; Lever can be pulled and pushed smoothly, with no distortion, no loosening, no obstruction; junction between lever and body of box is without cracking and loosing; locks shall be normal in use Lever can be pulled and pushed smoothly, with no distortion, no loosening, no obstruction; junction between lever and body of box is without cracking and loosing. Trolley Bag Size/mm Load/kg 455 (18 ) ~535 (18 ~21 ) ~610 (22 ~24 ) ~710 (25 ~28 ) ~785 (29 ~31 ) (32 ) 28 Travelling Case Size/mm Load/kg < ~ ~500 7 > Surface of hard boxes shall bear static pressure continuously for 4h under specified load, without distortion and cracking in box body and openings, and with no collapse in the box shell. 40 Degrees Hardness of surface of Aluminum openings of box shall be not less than 40 Brinell degrees. 104

105 Function Lockers Review QB/T Privacy of locks: locks shall be normal in use, without jumped number, decoupling and disorderly number. Flexibility of locks: the key shall be smooth in insertion and pull, with flexible lock core rotation. Durability of locks: under random combination of digitals for the coded lock, it shall not fail after 50 times of switch tests. The lock could not work more than 1 cycle within 10 cycles when using non-match key Impact Resistance QB/T No Major Defects Tensile Test of Zipper Puller QB/T Functional Zipper Details Refer to Remark Table 2 & 3 Children Safety Test Use and Abuse GB6675 / Hardware Labeling for China Market Permanent Label QB/T s Certificate/ Hangtags Remarks QB/T s No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 1. Name & Address of Manufacturer / Distributor 2. Brand Name 3. Certificate (Certification Logo) 4. Notes for Use and Storage Conditions 5. Name 6. Batch Number (Style Number) 7. Color 8. Quantity 9. Manufacturing Date (Month & Year) 1. Name 2. Standard 3. Size 4. Batch Number (Style Number) 5. Materials Compositions and Contents 6. Certification Logo Remark 1 1 Appearance requirements 1.1 Box (package) body It is upright in body, straight in gear line; steady and firm in erect position, and without rugged and skewness phenomenon. 1.2 Box (bag) surface 1.1 Soft boxes and bags Fabric color shall match; it shall be with no obvious vertical stitching pleats, bow wrinkles on seams, and shall be clean as a whole and without stains. Any obvious defects shall not be allowed on surface of leather fabric; any clear bump and pimple and tracks shall not be allowed on man-made leather and synthetic leather fabric; the main parts of textile fabrics may not have any breaks both in warp and in weft, and without floating thread and any other defects, and less than two slight flaws are allowed at secondary parts of the qualified products. 1.2 Hard box Box shall not have uneven surfaces, cracks, deformation, burns and other defects, and shall be overall clean and without stains. 1.3 Box openings With fitting closely, and seams between matching bottom and cover of box shall be not greater than 2mm, seam gap for grippedopenings box shall be less than 3mm, openings and walls shall be assembled closely and tightly. Smashes, scratches and burrs shall not be allowed at Aluminum openings of box, while color of the metal surface protection layer shall be in uniform. 1.4 Inner side of box Stitching and paste shall be bond, and the surface shall be smooth and tidy, and neat and clean, while the fabric shall not have any breaks both in warp and in weft, and without floating thread and any other defects. 1.5 Thread track Needle distance shall be uniform and straight, and it shall be in line between upper and lower thread track. There shall be no empty needle, drop needle, skipping stitch and breaks at key positions; less than two of these defects at secondary part shall be allowed, with no more than two stitches for each defect. 1.6 Zipper Stitches shall be smooth and straight, with a uniform edge distance and an error less than 2mm; it shall be smooth and free in pulling together, without dislocation and lost teeth. 1.7 Accessories (handles, levers, locks, hooks, rings, decorative pieces, etc.) Surface shall be smooth and without burrs. Metal plating shall be bright and in uniform color, no flaws, no rust, and without blistering, peeling and scratches. The surface coatings of plastic parts shall be of uniform color, with no flaw, hanging drop, wrinkle and peeling. 1.8 Identification Correct and clear. 105

106 Table 2 Breaking strength crosswise of chain (in N) Breaking strength crosswise of chain, Category Type of zipper Injection moulded zipper Nylon zipper Category Chemical fiber Table 3 Breaking strength crosswise of chain (in N) Breaking strength crosswise of chain, Type of zipper Cotton Chemical fiber Cotton Chemical fibe Cotton Chemical fiber Cotton Chemial fiber Cotton Chemical fiber Cotton Chemical fiber Cotton Metal Zipper C u A l

107 Stainless Steel Cup/ Water Bottle TEST DESCRIPTION Physical Construction review Usage Performance Children Safety Test TEST METHOD* QBT QBT MATERIAL/ COMPONENTS Use and Abuse GB 6675 / Hardware **Additional Restricted Substances (RS) Test Stainless Steel Composition (For China market only) Extractable Heavy Metals (For China market only) Labeling for China Market Marking QBT QBT GB 9684 QBT Section Section Food Contacting Components - Stainless Steel Food Contacting Components - Stainless Steel / Package The at least meets the PASS GRADE requirement. Details refer to Remark Table 1. No Loss Welding At Spot Welding / No Water Leak, No Separation of Parts No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges Stainless steel plates shall be in accordance with steel grade of 1Cr18Ni9 and 0Cr19Ni9 specified in GB/T 3284,or use other steel grades whose properties are not inferior to the above one. Details refer to Remarks Table 2 : - Manufactuer Name - Name and Specification - Trademark - item number - The mark of the grade of product Package: - Manufactuer Name - Name and Specification - Trademark - item number - The mark of the grade of product Remarks Serial No. Items to be checked Reject Category 1 Wrinkle B Not allowed Not allowed 2 Scratching C Not allowed 3 Pit C Not allowed 4 Dent C Not allowed Table 1 Quality requirements Excellent First-class Body Lid Body Lid Body Lid Only one scratch line, which the length shall not be more than half of body height and the width between mm, is allowed on interior. Scratching on other parts is not allowed. Only one 1-3mm pit is allowed Only one 2mm dent is allowed. Not allowed Not allowed Total length at the rim shall be 6% of the diameter of opening; other part are not allowed. Only two scratch lines on interior or one line on the bottom are allowed. The scratch line length shall not be more than half of body height and the width between mm. Scratching on other parts is not allowed. Total length at the rim shall be 3% of the diameter of opening; other parts are not allowed. Only one scratch line, which the length shall not be more than half of body height and the width between mm, is allowed on interior. Scratching on other parts is not allowed. Only one 5mm pit is allowed Only two 2mm dent is allowed. Sharp points are Only one 2mm dent is allowed. 107

108 5 6 7 Roughness of glazed surface μm Roughness of sanding surface μm Curl Edge Cut edge 8 Spot welding C No black spotting or burr B B B Sharp points are not allowed not allowed Sharp points are not allowed The max. allowed Rn value is 0.20, uniform, neat and no scrapes The max. allowed Rn value is 0.20 The max. allowed Rn value is 1.60, uniform and neat The max. allowed Rn value is 1.60 Continuously and tightly curled, smooth, and the Continuously and tightly curled, and clearance between curl edge and wall should be the clearance between curl edge 0.20mm and wall should be 0.50mm Smooh no cracks or sharp edges 9 Verticality of handle C 2mm 2.5mm Fitting of cover in body Axialalignment of cover and cover hole B C Freely rotate, and open/ close smoothly 1% of cover diameter of pening 12 Pattern C Uniform, neat and no focal spots 13 Marking C Accurate, complete, appropriately placed, clear and visible and no readable characters on back side Accurate, complete, andvisible 14 Bakelight Smooth, neat and no defecs such as notches, bubbles, blow holes, cracking and C accessories obvious discoloration. a. Excellent products: not more than one Category C reject; b. First-class products: not more than two Category C rejects; c. : not more than one Category B reject and one Category C reject, or three Category C rejects. Table 2 Item Indicator Austenitic stainless steel Martensitic stainless steel Plumbum (Pb), mg/l in 4% acetic acid soak solution Chromium (Cr), mg/l in 4% acetic acid soak solution Nickel(Ni), mg/l in 4% acetic acid soak solution Cadmium (Cd), mg/l in 4% acetic acid soak solution Arsenic (As), mg/l in 4% acetic acid soak solution Note: All soaking conditions are required to boil the solution for 30 ints and then keep it at room temperature for 24 hours. Approved by the Ministry of Health of the People s Republic of China on August 10th,1988 Implemented from June 11th, 1989 GB

109 Towel TEST DESCRIPTION Fiber Content Fiber Content Colorfastness Crocking Washing Perspiration Water Non-chlorine Bleach Physical Construction / Workmanship review Total Weight TEST METHOD* GB/T GB/T GB/T 3920 GB/T GB/T 3921 MATERIAL/ COMPONENTS Textiles (Except White Color and non-dyed material) Textiles (Except White Color and non-dyed material) Comply with FZ/T Single Fiber: no tolerance 2. Blends >15%: +/-5% Blends 15%: +/-30% of the claimed fiber Dry: Minimum 3.0 Wet: Minimum 2.5 Minimum 3.0 GB GB/T 3922 Textiles Minimum 3.0 GB GB/T 5713 Textiles (Except White Color and non-dyed material) Minimum 3.0 GB/T GB/T 7069 Textiles Minimum 3.0 GB/T The at least meets the PASS GRADE / Hardware requirement. Details refer to Remark Table 1 GB/T 9995; GB/T 9994 Each 10pcs: Minimum -4.5% Measurement Tensile Strength Absorbance Fiber shedding Children Safety Test GB/T GB/T GB/T GB/T Minimum -3.5% Minimum 180N (40 Pounds) Maximum 30 s Use and Abuse GB6675 / Hardware Labeling for China Market Permanent Label GB Certificate/ Hangtags GB Non-Cut Pile: Maximum 1.5% Cut Pile: Maximum 2.0% No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 1. Fiber Content 2. Sizes 3. Care Instruction Details refer to Remark 2 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Country of Origin 6. Materials (Fiber Content) 7. Care Instruction 8. Standard 9. Quality Grade 10. Category A, B or C 11. Certificate (Inspection Logo) 12. Name & Address of Manufacturer / Distributor 13. Notes for Use and Storage Conditions if necessary Details refer to Remark 3 109

110 Remarks Table 1 Quality requirements for appearance Serial Items to be checked Excellent First-class Note No. 1 Size deviation/% +3.0~ If absolute value of size deviation to be checked is less than 1cm, it shall be checked as of 1cm. 2 Linear defects/(location/linear) Square acecloth Bath towel Not allowed Back of cut pile fabrics productsshall Towel blanket 6 10 make reference Cut pile facecloth Not allowed to the non-cut 1 pile fabrics products. Cut pile bath 1 2 towel Cut pile towe 2 3 blanket Strip defects /(location Square ashcloth Not allowed 1 3 /linear) Bath towel 2 4 Towel blanket 3 6 Cut pile facecloth Not allowed 1 Cut pile bath 1 2 towel Cut pile towel 2 3 blanket Block defects Not allowed Minor Obvious Oil, color stains Not allowed Not allowed Minor Breakage defects Not allowed Scattered defects Minor Not allowed Allowed Allowed obvious Not allowed Printing and dying defects Color difference and paint stains Level 4 Level 3-4 Level 3 Print effects Not affecting the appearance 3 Seam quality No back stitching, loosen corner Not allowed Not allowed Slight Only one skipping stitch allowed Skipping stitch Not allowed Not allowed Less than 2 4 Quality of tiding and ironing and drop thread Needle density of flatlock stitches Needle density of overcast stitches Towel is not smooth andtidy Size of both sides is not matched spots/stip 14 stitches /5 cm 12 stitches5 cm 16 stitches /5 cm 14 stitches /5 cm Minor Minor obvious obvious Minor defect is hard to observe by visual check, while obvious defect is easy to be found out by visual check; minor defect in oil and color stains is of Grade 4 or above specified in GB/T250 color chart; color difference between strips in a same package for excellent product and first class product shall be better than Grade 4 or above in GB/T250 color chart. Note: Description of defects shall be as specified in Annex A. 110

111 1. Permanent Label for Textile s and Apparel Remark 2 According to GB Instruction for use of products of consumer interest Instructions for use of textiles and apparel, all the Textile s and Apparel sold in China are required to attach the legible label (i.e. permanent label) and be able to subject to use duration described in use instruction Contents of Permanent Label Permanent Label includes below information: a. Fiber Content (refer to FZ/T 01053) b. Sizes (refer to GB/T to GB/T ) c. Care Instruction 1. Washing Symbols (graphic symbols specified in GB/T 8685 and with their corresponding simple declaration text) 2. If symbols are not enough to explain, the short text can be added, but it shall be not in parallel with note to symbols meaning 1.2. How to show the Permanent Label The permanent label shall be permanently adhered on the suitable position of product: a. The label of size or specification 1. For apparel it can be sewn in middle of the collar. For the cover coat and business suit it can also sewn on the top or down edge of inside pocket of jacket; For the trouser or skirt on the lower edge of waistband. 2. For other textile products, e.g. scarf, towel etc, can be sewn on the corners b. The label of material compositions and contents, care instruction 1. The material composition and contents, care instruction can be indicated on a label together. 2. For apparel, it can be generally sewn on the lower middle position of left seam For the skirts and trouser can be sewn on the lower edge of waistband or upper position of skirt left seam, trouser side seam 3. For other textile products, e.g. scarf, towel etc, can be sewn on the corners 1 Content of Instruction Remark Name and address of the manufacturer It shall be marked the name and address that are registered according to law by the manufacturers of textiles and clothing. The product origin (country or region) and the name and address of the imported textiles and clothing that are registered according to law by the agent or importer or distributor shall be marked in Chinese. 1.2 name name shall indicate its real characteristics and shall meet the following REQUIREMENT: In case of specifications for product names existing in national standards or industry standards, these names shall be used In case of specifications for product names not existing in national standards or industry standards, common names or popular names that will not cause misunderstanding and confusion shall be used; For marking of "strange name" and "trade name", a name specified in or shall be clearly marked in same position. 1.3 models and specifications Marking of sizes or specifications of textile shall comply with the relevant national or industry standards. Type of clothes shall be indicated in accordance with the REQUIREMENT in GB / T ~ Composition and content of raw materials Name and content of composition of raw materials shall be marked, while the marking of fiber content shall be in accordance with the REQUIREMENT in FZ/T01053, please see Appendix A (Normative) for example. For leather garments, it shall mark the leather s type name which shall show the real characteristics of the products, and if there are any specifications in standards, the relevant national, industry or corporate standards shall be followed. 1.5 Washing Washing methods shall be provided with the graphical symbols given in GB/T8685, with a simple descriptive text corresponding to the graphic symbols being noted underline When the graphic symbols can not meet the needs, concise text can be given for description, but it shall not be placed side by side with the above said descriptive notes The letter A, P, F shall be added as dry cleaning symbols to illustrate the type of dry cleaning agent. (See Appendix B (Normative)). 1.6 Precautions of use and storage conditions Improper use may cause damage to the product, and the product shall be indicated with the precautions for use. If it is need to be stored, the storage methods shall be briefly indicated. 1.7 Lifetime of For product that needs to be used in a limited time period, it shall be marked with production date and the effective lifetime (date shall be marked in order of year, month, day). 1.8 Standards No. The number of all implemented national standards, industry standards or enterprise standards shall be marked. 1.9 quality rating For the product with its quality ratings clearly defined in Standards, it shall mark the quality ratings in accordance with the REQUIREMENT in relevant standards Quality certificate of product 111

112 For qualified products produced domestically, each single product (sales unit) shall have its quality certificate of inspection. 2 Form of Instruction 2.1 The following form shall be used according to the characteristics of products a. The instructions directly printed or weaved on the product; b. Labels stitched, pasted, or hung on the product; c. The instructions directly printed on the product packaging; d. Washing methods include washing with water, chlorine bleaching, ironing, drying after washing, dry cleaning, and other methods. e. Labels attached on the product packaging; f. Materials provided along with the product information. 2.2 s sizes or specifications, the composition and content of used raw materials, washing method and other contents shall be in durable labels (see 3.4). In which, the composition and content of raw materials and washing methods, etc shall be marked in combination on one label. If the used durable label affects the use of products, such as in the case of fabric, yarn and sewing thread and stocks and other products, the durable label shall not be used. 2.3 If the products are packaged, displayed or scrolled, and the consumer is not easy to find the information on the instruction label, you shall give this information in other forms of instructions. 2.4 When several types of instructions were used simultaneously, it shall ensure the consistency of their contents. 3 Placement of instructions 3.1 The instructions shall be attached to the product or packaging on an obvious parts or an appropriate parts. 3.2 The instructions shall be provided in single product unit or sale unit. 3.3 Location of durable label The durable label shall be permanently attached to the product in an appropriate location Label location of clothing product Type signs or specifications and other kind of labels for apparel products shall be normally in placed or sewn in center of back collar. In which, the labels for coats and suits can also be sewn on upper edge or lower edge of inner placket of front waistband; labels for pants and skirt can be sewn on lower edge of inner waist Composition and content of raw materials and washing methods of clothing products shall be generally sewn on middle and lower part of left seam. Labels for pants and skirt can be sewn on lower edge of inner waist or left seam of skirt or upper part of pants seam Label for products of scarves and shawls can be sewn in edges or corners Labels of ties shall be sewn on wide or narrow part of joint seams of tie back Labels on household textiles (tablecloths, bed sheets, towels, bedspreads, blankets, etc.) shall be sewn on edges or corners. 3.4 Placement of instruction labels of fabric, yarn and sewing thread, socks and other textile products Instruction labels of cloth shall be placed in one of the following ways: a. The label or tag attached to end of fabric rolls; b. The label or tag printed or woven on the weaving edge Instruction content of yarn and sewing thread shall be marked on tag or shell ring of coil, ball and hoop Instruction content socks can be marked on the label at top of socks Label for other textile product shall be placed on its appropriate locations. 3.5 Labels of special technological products shall be placed according to the specific needs. 112

113 Umbrella TEST DESCRIPTION Colorfastness Water TEST METHOD* GB/T GB 250/ GB/T 251 MATERIAL/ COMPONENTS Textiles Minimum 3.0 Physical Construction review / Appearance Integrity Stability Manual Function of Spring Strength for switch Assembly component strength Pole resistance to wind Operability of switch Flexibility of Umbrella Bone Bone Resistance to Wind UV Protection Salt Spray Test Water Repellency of Fabric /Spray Test Children Safety Test GB/T / 5.2 / 5.3 / 5.4 GB/T GB/T GB/T GB/T GB/T GB/T GB/T GB/T GB/T GB/T GB/T QB/T 3826: SALT SPRAY: SALT SPRAY Salt Spray QB/T 3832 GB/T / Hardware / Hardware / Hardware / Hardware / Hardware Hardware Hardware Textiles (i) No Safety Hazards & (ii) Cleanliness & No Rusting (iii) Seaming: Umbrella joints shall not have separations and exposing side, and shall have not skipping stitches, broken and other defects, with needle density being not less than 15 stitches within a distance of 5cm. (iv) Surface: Patterns on umbrella surface shall not have obvious dislocation. (v) Dimension: Deviation +/- 8mm Integrity, No detached components No loosen parts Spring is workable and stable when opening. Greater than 10N (2.2 Pounds) and Less than 70N (15.4 Pounds) The part between umbrella rods, and between umbrella rod and handle bar shall be without any dislocation under a static tension of 150N. The part between umbrella rod and umbrella cap shall be without any dislocation under a static tension of 70N. No Distortion After 600 times of opening and closing, no damage There shall not have rivets falling, clipping, clipper shift, string plate wire fracture, loosing, umbrella slot defect, spring failure, umbrella bone fracture, joint separation, slit eyes off-line, handle shift, plated coating spalling and other phenomenon after 600 switches operations for hand open straight umbrella, 400 switches for automatic open straight umbrella, 400 switches for hand open reduction folding umbrella, and 400 switches for automatic open reduction folding umbrella, as well as 400 switches for automatic open and automatic folding umbrella. <10mm Elasticity of umbrella bone (only for straight bone umbrella) The distance between two ends shall shorten by 20% when the long bone is bent into arc, while the height of chord after unloading shall be not greater than 10mm. No Damage UPF>40, T(UVA)AV<5% Hardware Minimum Grade 5 Textiles After the test, umbrella pole shall not drip water; inner side of umbrella surface shall not have water drop and shall not have obvious water mist. It shall be shown expressly if it have no rain-proof characteristics of the products. It shall be clean and free of dirt and rusts in appearance. 113

114 Use and Abuse Labeling for China Market Certificate/ Hangtags GB 6675 GB/T / Hardware No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Standard 6. Quality Grade 7. Certificate (Inspection Logo) 8. Name & Address of Manufacturer / Distributor 114

115 Baby Changing Pads TEST DESCRIPTION Fiber Content TEST METHOD* Fiber Content FZ/T Colorfastness Crocking Washing Perspiration GB GB/T 3920 GB GB/T GB GB/T 3922 GB Water GB/T 5713 Children Safety Test MATERIAL/ COMPONENTS Textiles (Except White Color and non-dyed material) Textiles (Except White Color and non-dyed material) Textiles Textiles Use and Abuse GB6675 / Hardware Labeling for China Market Permanent Label GB Certificate/ Hangtags GB Comply with FZ/T Single Fiber: no tolerance 2. Blends >15%: +/-5% Blends 15%: +/-30% of the claimed fiber Dry: Minimum 4 Wet: Minimum 3 (Dark: Minimum 2.5) Color Change: Minimum 3.0 Color Stain: Minimum 3.0 Color Change Minimum 3.5 Color Stain: Minimum 3.5 Color Change Minimum 3.5 Color Stain: Minimum 3.5 No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 1. Fiber Content 2. Sizes 3. Care Instruction 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Country of Origin 6. Materials (Fiber Content) 7. Care Instruction 8. Standard 9. Quality Grade 10. Category A, B or C 11. Certificate (Inspection Logo) 12. Name & Address of Manufacturer / Distributor 13. Notes for Use and Storage Conditions if necessary 115

116 2.2.6 Pet Items Pet Apparel TEST DESCRIPTION Fiber Content Fiber Content Care Label Care Label Verification Colorfastness Crocking TEST METHOD* FZ/T FZ/T FZ/T GB/T 3920 MATERIAL/ COMPONENTS Textile Textiles/Leather (Except White Color and non-dyed material) Comply with FZ/T Single Fiber: no tolerance 2. Blends >15%: +/-5% Blends 15%: +/-30% of the claimed fiber Shrinkage Machine Wash Collar/Chest/Back Length: -2.0% x 0.0%/-3.5% x 0.0%/-3.5% x 0.0% Shrinkage Dry Cleaning Collar/Chest/Back Length: -2.0% x 0.0%/-3.5% x 0.0%/-3.5% x 0.0% Dry: Minimum 3.0 Wet: Minimum 2.5 Washing Dry Cleaning Physical Construction / Workmanship review Safety Test FZ/T GB/T FZ/T GB/T 5711 FZ/T Textiles (Except White Color and non-dyed material) / Hardware Use and Abuse GB6675 / Hardware Labeling for China Market Color Change: Minimum 3.0 Color Stain: Minimum 3.0 Color Change: Minimum 3.0 Color Stain: Minimum 2.5 The at least meets the PASS GRADE requirement. Details refer to Remark Table 1, 2, 3 & 4 No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges Permanent Label GB Fiber Content 2. Sizes 3. Care Instruction Details refer to Remark 5 Certificate/ Hangtags GB Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Country of Origin 6. Materials (Fiber Content) 7. Care Instruction 8. Standard 9. Quality Grade 10. Category A, B or C 11. Certificate (Inspection Logo) 12. Name & Address of Manufacturer / Distributor 13. Notes for Use and Storage Conditions if necessary Details refer to Remark 6 116

117 Remarks Table 1 Item Allowable size deviation Collar size 士 1.5 Chest circumference 士 2.0 Back length 士 2.5 Note: Table 2 Name of defect Alloance level of surface defects Thread thicker than double of specified thickness 2 locations allowd Taking ut thread 1 location allowed Paint stain Not allowed Uneven in tickess 1 location allowed Spot defects(oil, rust, color spots) 1 location allowed Surface on each single product shall have one only above mentioned defect. If it is exceeded, the product shall be seen as unqualified. Table 3 Item Stitches density Remarks Light and dark stitches Not more than 12 stitches with a distance of Except for a specially designed product 3cm. Overcast stitches Not more than 9 stitches with a distance of 3cm. Item Serial N.o Instructions 1 Trademark is not upright and not correct and is significantly skewed; color of line binding trademark is incompatible with trademark background. Allowanable size deviation Table 4 Minor defects Major defects Serious defects Content of instructions is not accurate. Content of instructions is incomplete. 2 Deviation in size is within 50% of the value specified in this Standard. Deviation in size is 50% or over of the value specified in this Standard. Deviation in size is 100% or over of the value specified in this Standard. Defects 3 Over the values specified in this Stitches density Stitches quality in appearance 4 Not more than 2 stitches lower than that is specified in this Standard(including 2 stitches). 5 Thread is not adapting to the color and characteristics of the surface material. 6 Not smooth and tidy in ironing, with reflective light. More than 2 stitches lower than that is specified in this Standard. Standard. Slight yellowing and change in With deterioration or dilapidated. color 7 Ungluing, seepage of gum and wrinkling at pasted parts. 8 Having unobvious stains, powder stains not more than 2cm2; water spray not more than 4cm2. Having obvious stains over 2cm2 for outside materials and over 4cm2 for inside material; Having serious stains that is over 20cm2. 9 Uneven sewing and inappropriate elasticity in different parts. 10 There are two single skipping stitches within a distance of 20cm; various closed ends and back stitches are unfirm. 11 Difference of distance between keyholes is greater than 0.4cm; skew is greater than 0.2cm, with yarn extracting. 12 Difference between the location of button and of button hole is more than 0.2cm(including accessories); it is unfirm in buttoning. water spray over 4cm2. Having obvious creases and needle exposes at selvage at surface of outside material. Continuous skipping stitches or over one skipping stitch within a distance of 20cm. Thread skipping and unstitched, loss or breakage of thread for keyhole is more than 0.5cm. Difference between the locations of button and of button hole is more than 0.5cm(including accessories). 13 Not smooth and tidy in collar, and not symmetrical in collar style. 14 Color difference is half level lower than as specified in this Chain skipping stitches. Color difference on a single or a same batch of finished product 117

118 15 Decorative pieces not smooth and tidy, unfirm, and not round and smooth in the four corners of adhesive tape. Standard. Decorative pieces not correct, which significantly affects the appearance, and adhesive tape is unfirm in bonding. is more than one level lower than as specified in this Standard. Lost of buttons and accessories, metal pieces getting rust, lost or lack of decorative pieces. Note 1: The above mentioned defects shall be calculated in accumulation by serial number. Note 2: Defects not covered in this Table shall be determined as appropriate with reference to similar defects according to Defect Classification Rules. Note 3: Any lost in procedures, missing in work or wrong in sequence shall all be seen as major defects. Lack of parts shall be as serious defects. 1. Permanent Label for Textile s and Apparel Remark 5 According to GB Instruction for use of products of consumer interest Instructions for use of textiles and apparel, all the Textile s and Apparel sold in China are required to attach the legible label (i.e. permanent label) and be able to subject to use duration described in use instruction Contents of Permanent Label Permanent Label includes below information: a. Fiber Content (refer to FZ/T 01053) b. Sizes (refer to GB/T to GB/T ) c. Care Instruction 1. Washing Symbols (graphic symbols specified in GB/T 8685 and with their corresponding simple declaration text) 2. If symbols are not enough to explain, the short text can be added, but it shall be not in parallel with note to symbols meaning 1.2. How to show the Permanent Label The permanent label shall be permanently adhered on the suitable position of product: a. The label of size or specification 1. For apparel it can be sewn in middle of the collar. For the cover coat and business suit it can also sewn on the top or down edge of inside pocket of jacket; For the trouser or skirt on the lower edge of waistband. 2. For other textile products, e.g. scarf, towel etc, can be sewn on the corners b. The label of material compositions and contents, care instruction 1. The material composition and contents, care instruction can be indicated on a label together. 2. For apparel, it can be generally sewn on the lower middle position of left seam For the skirts and trouser can be sewn on the lower edge of waistband or upper position of skirt left seam, trouser side seam 3. For other textile products, e.g. scarf, towel etc, can be sewn on the corners 1 Content of Instruction Remark Name and address of the manufacturer It shall be marked the name and address that are registered according to law by the manufacturers of textiles and clothing. The product origin (country or region) and the name and address of the imported textiles and clothing that are registered according to law by the agent or importer or distributor shall be marked in Chinese. 1.2 name name shall indicate its real characteristics and shall meet the following REQUIREMENT: In case of specifications for product names existing in national standards or industry standards, these names shall be used In case of specifications for product names not existing in national standards or industry standards, common names or popular names that will not cause misunderstanding and confusion shall be used; For marking of "strange name" and "trade name", a name specified in or shall be clearly marked in same position. 1.3 models and specifications Marking of sizes or specifications of textile shall comply with the relevant national or industry standards. Type of clothes shall be indicated in accordance with the REQUIREMENT in GB / T ~ Composition and content of raw materials Name and content of composition of raw materials shall be marked, while the marking of fiber content shall be in accordance with the REQUIREMENT in FZ/T01053, please see Appendix A (Normative) for example. For leather garments, it shall mark the leather s type name which shall show the real characteristics of the products, and if there are any specifications in standards, the relevant national, industry or corporate standards shall be followed. 1.5 Washing Washing methods shall be provided with the graphical symbols given in GB/T8685, with a simple descriptive text corresponding to the graphic symbols being noted underline When the graphic symbols can not meet the needs, concise text can be given for description, but it shall not be placed side by side with the above said descriptive notes The letter A, P, F shall be added as dry cleaning symbols to illustrate the type of dry cleaning agent. (See Appendix B 118

119 (Normative)). 1.6 Precautions of use and storage conditions Improper use may cause damage to the product, and the product shall be indicated with the precautions for use. If it is need to be stored, the storage methods shall be briefly indicated. 1.7 Lifetime of For product that needs to be used in a limited time period, it shall be marked with production date and the effective lifetime (date shall be marked in order of year, month, day). 1.8 Standards No. The number of all implemented national standards, industry standards or enterprise standards shall be marked. 1.9 quality rating For the product with its quality ratings clearly defined in Standards, it shall mark the quality ratings in accordance with the REQUIREMENT in relevant standards Quality certificate of product For qualified products produced domestically, each single product (sales unit) shall have its quality certificate of inspection. 2 Form of Instruction 2.1 The following form shall be used according to the characteristics of products a. The instructions directly printed or weaved on the product; b. Labels stitched, pasted, or hung on the product; c. The instructions directly printed on the product packaging; d. Washing methods include washing with water, chlorine bleaching, ironing, drying after washing, dry cleaning, and other methods. e. Labels attached on the product packaging; f. Materials provided along with the product information. 2.2 s sizes or specifications, the composition and content of used raw materials, washing method and other contents shall be in durable labels (see 3.4). In which, the composition and content of raw materials and washing methods, etc shall be marked in combination on one label. If the used durable label affects the use of products, such as in the case of fabric, yarn and sewing thread and stocks and other products, the durable label shall not be used. 2.3 If the products are packaged, displayed or scrolled, and the consumer is not easy to find the information on the instruction label, you shall give this information in other forms of instructions. 2.4 When several types of instructions were used simultaneously, it shall ensure the consistency of their contents. 3 Placement of instructions 3.1 The instructions shall be attached to the product or packaging on an obvious parts or an appropriate parts. 3.2 The instructions shall be provided in single product unit or sale unit. 3.3 Location of durable label The durable label shall be permanently attached to the product in an appropriate location Label location of clothing product Type signs or specifications and other kind of labels for apparel products shall be normally in placed or sewn in center of back collar. In which, the labels for coats and suits can also be sewn on upper edge or lower edge of inner placket of front waistband; labels for pants and skirt can be sewn on lower edge of inner waist Composition and content of raw materials and washing methods of clothing products shall be generally sewn on middle and lower part of left seam. Labels for pants and skirt can be sewn on lower edge of inner waist or left seam of skirt or upper part of pants seam Label for products of scarves and shawls can be sewn in edges or corners Labels of ties shall be sewn on wide or narrow part of joint seams of tie back Labels on household textiles (tablecloths, bed sheets, towels, bedspreads, blankets, etc.) shall be sewn on edges or corners. 3.4 Placement of instruction labels of fabric, yarn and sewing thread, socks and other textile products Instruction labels of cloth shall be placed in one of the following ways: a. The label or tag attached to end of fabric rolls; b. The label or tag printed or woven on the weaving edge Instruction content of yarn and sewing thread shall be marked on tag or shell ring of coil, ball and hoop Instruction content socks can be marked on the label at top of socks Label for other textile product shall be placed on its appropriate locations. 3.5 Labels of special technological products shall be placed according to the specific needs. 119

120 Pet Bed TEST DESCRIPTION Colorfastness TEST METHOD* MATERIAL/ COMPONENTS Crocking GB GB/T 3920 Textiles/Leather (Except White Color and non-dyed material) Minimum 3.0 Perspiration GB GB/T 3922 Textles Color Change: Minimum 3.0 Color Stain: Minimum 3.0 Water GB GB/T 5713 Textles Color Change: Minimum 3.0 Color Stain: Minimum 3.0 Children Safety Test Use and Abuse GB6675 / Hardware Labeling for China Market Permanent Label GB Certificate/ Hangtags GB No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 1. Fiber Content 2. Sizes 3. Care Instruction 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Country of Origin 6. Materials (Fiber Content) 7. Care Instruction 8. Standard 9. Quality Grade 10. Category A, B or C 11. Certificate (Inspection Logo) 12. Name & Address of Manufacturer / Distributor 13. Notes for Use and Storage Conditions if necessary 120

121 Pet Bowl TEST DESCRIPTION Safety Test TEST METHOD* MATERIAL/ COMPONENTS Use and Abuse GB6675 / Hardware Labeling for China Market Certificate/ Hangtags Visual No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Quality Grade 5. Name & Address of Manufacturer / Distributor 121

122 Pet Carrier Bags TEST DESCRIPTION Colorfastness Crocking TEST METHOD* QB/T GB/T 3920 (For Textile) QB/T 2537 (For Leather) MATERIAL/ COMPONENTS Textiles / Leather (Except White Color and non-dyed material) Dry: Minimum 4.0 Wet: Minimum 3.0 Physical Workmanship QB/T Seam Strength QB/T Manual Function and Cycling of Hardware PU / PVC / Fabric / Leather (Sheep & Lamb Skin) The at least meets the PASS GRADE requirement. Details refer to Remark Table 1 Minimum 196N (44 Pounds) (For Outer) QB/T Hardware After 200 cycles: No obvious change of Accessories Zipper Durability QB/T Functional Zipper Handle integrity QB/T Salt Spray Test Children Safety Test QB/T QB/T 3826: Salt Spray Hardware Use and Abuse GB6675 / Hardware Labeling for China Market After 200 cycles (PASS GRADE) No Losing and Staggering of Tooth, No Breaking of Zipper No losing of shoulder strip, back strip and hook; Not breaking of body; straps should not have over 30% distortion Corrosion area <= 1mm² No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges Certificate/ Hangtags QB/T / QB/T Brand Name 2. Name 3. Batch Number (Style Number) 4. Size 5. Color 6. Country of Origin 7. ion Date (Month & Year) 8. Materials 9. Standard 10. Quality Grade 11. Certificate (Inspection Logo) 12. Name & Address of Manufacturer / Distributor 122

123 Remarks Table 1 Quality requirements for appearance Requirements Excellent product product Serial Items to be tested No. 1 Overall appearance Full and plumb in style, fluent in lines, closely and straight in paste, symmetrical and correct in corners, neat and clean in whole appearance. 2 Main Fabric Leather Artificial leather, and synthetic leather Textile fabric Uniform in thickness, no crazing of leather, grain crack, decoloration and other defective phenomenon. Surface shall be smooth and straight, and without breakage in large surface in back and front, and no obvious tracks and creases shall be allowed. Without any tracks, bumps and knots. Without any broken warp and broken weft, and with no floating threads, skipped stitches, tracks, stains and flaws. Full and plumb in style, fluent in lines, closely and straight in paste, symmetrical and correct by and large in corners, neat and clean in whole appearance. Uniform in thickness, no cleaves in surface and no crazing of leather, grain crack, decoloration and other defective phenomenon. Surface shall be smooth and straight, allowing 2 coarse stains in large surface in back and front which is less than 9mm2, and allowing 2 obscure tracks and creases. Without any obvious tracks, bumps and knots. Main body without any broken warp and broken weft, and with no floating threads, skipped stitches, obvious tracks and stains.; and allowing 2 obscure tracks and stains are allowed in minor parts 3 Lining Fabric Shall be smooth and straight,neat and clean, no crazing, broken warp and broken weft, and with no floating threads, skipped stitches etc. 4 Seam Seam shall conform to the fabrics and lining, with its quality, color adapting to the surrounding parts. 5 Seam track Needle distance shall be uniform and straight, and it shall be in line between upper and lower thread track. Surface of bags shall not have empty needle, lost needle, skipping stitch, and shall not have skews in thread track. Needle distance shall be uniform and straight, and it shall be in line between upper and lower thread track. Large front surface and front cover of bags shall not have empty needle, lost needle and skipping stitches. Track skew over 15mm shall not be allowed. Empty needles, drop needle and lost stitches on each single product shall be not more than one, with the empty needles, lost stitches and skipping stitches being not more than 2 needles. 6 Zipper No teeth dislocation, no teeth missing, smooth and straight in stitches, uniform in edge distance, smooth and free in pulling together; no any color losing 7 Accessories The surface is smooth and bright, with no rust, no burrs, no pinholes, and no blistering, no peeling, no shedding and obvious scratches. The surface is smooth and bright, with no rust, no burrs, and no peeling, no shedding and other phenomenon. 8 Mounting accessories Smooth, straight and firm. 9 Standard samples * samples must be attached to the bag back with exactly the same subject material. Remark: * Inspect on handbag contains standard sample only, would not inspect if no standard sample. 123

124 Pet Collar/Leash TEST DESCRIPTION Safety Test TEST METHOD* MATERIAL/ COMPONENTS Use and Abuse GB6675 / Hardware Labeling for China Market Certificate/ Hangtags Visual No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 1. Brand Name 2. Name 3. Batch Number (Style Number) 4. Quality Grade 5. Name & Address of Manufacturer / Distributor 124

125 Pet Toys TEST DESCRIPTION Assessment TEST METHOD* Assessment GB 6675 Safety Test MATERIAL/ COMPONENTS Use and Abuse GB 6675 / Hardware (i) (ii) No Safety Hazards All Toys must be assessed for Play Value, if the toy is applied to children other than pets, then the toy must be subject to local countries toy requirements No Safety Hazards or release of parts - No Small Parts & Sharp Points/Edges after abuse test Drop Tests - 10 drops from 4.5 feet Torque - Min. 4.0 in-lb applied for 10 seconds Tension - Min. of 50.0 lb applied for 10 seconds for dog toys. Min. of 15.0 lb applied for 10 seconds for all others. Tension Tests For Seams - Min. of 21.0 lb of force for dog toy. Min. of 15.0 lb for all others Compression Test lb applied for 10 seconds for dog toys. Min of 30.0lb for all others Flexure Test - bent through a 60 arc by a 15 lb perpendicular force for 30 cycles 125

126 2.2.7 Stationery Magnetic Poetry Kit TEST DESCRIPTION Children Safety Test TEST METHOD* MATERIAL/ COMPONENTS Use and Abuse GB 6675 / Hardware Flammability Flammability (Solids) GB 6675 Reference Photo: 1) No Safety Hazards - No Small Parts & Sharp Points/Edges 2) Comply with the relevant regulatory REQUIREMENT 1) 16 CFR : - Maximum 0.1inch/sec 2) EN71-Part 2: - Shall not be more than 30 mm/s or shall self extinguish 3) Japan Toy Standard Part 2: - No Surface Flash (for raised fabric) - Not more than 30 mm/s 4) GB Comply with the regulatory REQUIREMENT 126

127 Photo Album TEST DESCRIPTION Physical Basic dimensions Thickness and haze of PP film (Optional) Thickness and haze of PVC film (Optional) Thickness of BOPP film (Optional) Quantification weight of Single-faced White Board (Optional) Quantification weight of copperplate paper (Optional) Quantification weight of two-sided offset paper (Optional) Cardboard thickness required for capsule (Optional) Technical indicatorscapsule Technical indicatorsmildew Technical indicators- drift cut (MM) Technical indicators - water content (%) Technical indicators smoothness and cleaning (MM) Technical indicators temperature range( ) in which viscose will not degum Technical indicators - core Technical indicators Hot-press fastness (N/15MM) Technical indicators - Viscose strips Technical indicators - Viscose inside Children Safety Test TEST METHOD* QB/T Section 5.1, 6.1 QB/T Section 5.2, 6.2 QB/T Section 5.3, 6.2 QB/T Section 5.4, 6.2 QB/T Section 5.5, 6.3 QB/T Section 5.6, 6.3 QB/T Section 5.7, 6.3 QB/T Section 5.8, 6.3 QB/T Section 5.9, 6.5 QB/T Section 5.9, 6.5 QB/T Section 5.9, 6.6 QB/T Section 5.9, 6.7 QB/T Section 5.9, 6.8 QB/T Section 5.9, 6.9 QB/T Section 5.9, 6.5 QB/T Section 5.9, 6.10 QB/T Section 5.9, 6.6 QB/T Section 5.9, 6.5 MATERIAL/ COMPONENTS Specifications (basic size) of photo albums and name card book shall be in accordance with that is required in Company standards, with a limit deviation of ±1.5mm. Thickness of PP film shall be not less than 0.04mm, and its haze shall be not more than 4.0%. Thickness of PVC film shall be not less than 0.04mm, and its haze shall be not more than 2.8%. Thickness of BOPP film shall be not less than 0.02mm. Quantification weight of Single-faced white board shall be not less than 200g/m 2. Quantification weight of copperplate paper shall be not less than 100g/m 2. Quantification weight of two-sided offset paper shall be not less than 60g/m 2. Cardboard thickness for capsule required shall be not less than 1.5mm. Its surface shall be smooth and clean, without obvious defects, damages, blisters, wrinkles and other phenomenon. Color overprint shall be clear, with a deviation not more than 0.4MM. Hot stamping foil shall be clear and bright, strong in adhesion, with a deviation not more than 0.5MM. Local UV shining process shall give a smooth and light surface, without grains, and shall be strong in adhesion, with color overprint not more than 0.5MM No Deflection ~ Use and Abuse GB6675 / Hardware It shall be clean and shall be without peeling, missing of pages, breakages, upside downs, wrinkles and bending. Viscose strips shall be clear and complete. Breakage of thread: 5MM/book~ 20MM/; opening of thread: Shall be not more than 2 spots, and shall be not more than 2 pieces for each book. Pull with adhesives and other phenomena shall not appear for BOPP film, and its inside shall not have wave-shaped defects. No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges 127

128 Pen TEST DESCRIPTION Physical Construction review TEST METHOD* For Ball Point Pen and Refill: QB/T 2776 Section 5.1 MATERIAL/ COMPONENTS /Hardware Details refer to Remark Table 2, Table 3 item 6 Remark 4 & 5 Usage Performance Children Safety Test For Ball Point Pen and Refill: QB/T Use and Abuse GB6675 / Hardware Labeling for China Market Marking For Ball Point Pen and Refill: QB/T 2776 The at least meets the PASS GRADE requirement. Details refer to Remark Table 2, Table 3 item 1-5 No Safety Hazards 1) No Small Parts 2) No Sharp Points/Edges Ball Point Pen: 1. Manufacturer Name or Registered Trademark 2. Style Number Refill: 1. Manufacturer Name or Registered Trademark 2. Manufacturing Date (Month & Year) or Batch Number Remarks 1 Classification Table As for the specification of ball-point pen refill, it is designated as 67, 83, 96, 97, 97-1, 101, 101-1, 106, 115, 115-1, 140A and 140B respectively according to the length, ball diameter and refill head diameter. Please see Remark 5 (Drawing B.1-B.9) for the sizes of the above pen refills. 1.2 According to different structures, ball pens are divided into fixed type and movable type which falls into tilting type and rotational type. 1.3 Please see Table 1 for the classification of pen heads according to ball diameter. In mm Classification of pen heads Fine Medium Rough Diameter of ball D < D 0.8 D > 0.8 Table 2 SN Description Requirements 1 Starting characteristics 200mm does not suffer from abnormality. 2 D Ink Ball diameter/mm 0.5 < D volme/(mg/m) D > ink leak mark (circle) 10 4 Writing qality The line track does not suffer from obvious thinning, breaking or witing failure. Type 67 83, 96, Writing length/m Type 97, 101, 106, 115 1, 140A, 140B 1000 Type 91, Seepage/% 20 7 Light resistance/h 24 8 Water resitance/h 1 9 Aridity/s Ball fixation degree No ball falling * When Type 106, 140A and 140B use rough pen head, the model is affixed by digtal 1 and writing length is 500 mm. Table 3 1 Other properties of ball pens shall also in accordance with the requirements specified in Table 3. Please see Remark 4 for the internal and external requirements. SN Description Requirements 1 Flexibility of refill knockout mechanism a The change-over of using and reset of refill is flexible; At the reset position, the ball is not exposed. 2 Difference between pen head inner and outer diameter /mm

129 a b 3 Clamp force of metal clip b /N 0.15 Corrosion Clad layer 3 min without bottom exposure 4 surface physical and resistance Oxide layer 1.0 without botom exposure chemical performance Bonding strength of paint film Paint il does not suffer from peeling Hardness of paint film 2 H 5 Impact resistance The writing is normal; parts do not suffer from cracking, deformation or peeling. 1 The components are complete. 2 Mark characters are legible. 6 Appearance 3 The surface is smooth and clean. 4 The whole pen and fittings do not suffer from obvious inclined cracking or separate seam. It is only applicable to the movable ball pens. It is only applicable to the ball pen with fixed clamp, elastic clamp or spring clamp. Remark 4 A.1 Please see Table A.1 for the requirements of ball pen appearance, relevant test methods and ratio of model inspection qualification rate. Table A.1 Qualification rate Requirements The components are complete Mark characters are legible The surface is smooth and clean The whole pen and fittings do S N Provisions The whole pen has no lack of 1 components Concealed cracking at the mouth has a length of 2 mm; concealed cracking in 2 the middle of holder case has a length of 10mm. All components enjoy perfect 3 connection function without any ink leakage Contents of ball pen mark shall be in 1 accordance with Article and be legible Contents of pen refill mark shall be in 2 accordance with Article and be legible Packing mark and contents shall be in 3 accordance with Article 9.2 For holder case, length of thread is 15mm, width is 0.2mm (width of other 1 components is 0.1mm); pitch of thread is 10mm; number of thread is 2. Holder case snag length is 6mm; 2 width is 1.5mm; snag spacing is 10mm; number of snag is 2. Average diameter of mixed color and stain of external components is 3 0.6mm; distance is 10mm; number of points is 3. Average diameter of dot of external parts is 0.5mm; distance is 4 10mm; number of spots: for holder case, it is 2 respectively;for other components, it is 1 respectively. At mouth, each external component has no 2mm concealed thread; each 5 holder case has no 10mm concealed thread. The clad layer on each component is 6 not permitted to have any peeling crust. Bending degree of the whole pen is not 1 more than 0.4% of the whole length. Test method Ratio of one-item qualification rate for single product /% Ratio of qualification rate of inspection samples/% Total qualification rate/% Visual check 40/n Measured by venier caliper Visual check Visual check Visual check 30/n 12/n Visual check 6/n Measured by venier caliper Measured by venier caliper Measured by venier caliper Measured by venier caliper Measured by venier caliper Visual check 5/n 10/n See A.2 15/n

130 not suffer from obvious inclined separate seam The fit clearance between each component is 0.3mm. The axiality deviation of fit of each component is 0.3mm. The pencil clamp does not have any obvious inclination. Note: n refers to the number of inspection samples. Measured by feeler gauge Measured by venier caliper Contrast with sample by Visual check 5/n Remark 5 (Normative Appendix) Specification of Ball-point Pen Refill B.1 Please see Drawing B.1 B.9 for the specification of ball-point pen refill. Drawing B 1 67 ball-point pen refill Drawing B 2 83 ball-point pen refill Drawing B 3 96 ball-point pen refill 130

131 Note: Ball diameter is D > 0.8mm for 97 1 ball-point pen refill. Drawing B 4 97 and 97 1 ball-point pen refill Note: Ball diameter is D > 0.8mm for ball-point pen refill. Drawing B and ball-point pen refill Drawing B ball-point pen refill 131

132 Note: Ball diameter is D > 0.8mm for ball-point pen refill Drawing B and ball-point pen refill Drawing B 8 140A ball-point pen refill Drawing B 9 140B ball-point ball refill 132