Installation Instructions

Transcription

1 Installation Instructions s asy s I 200 Series Multi-Sized thru 6 Universal oor losers Tri-Pack Standard as 20 Regular rm Parallel rm Jamb Mount 200 IMPORTNT: OR INSTLLIN: Pages 2 & 20 Pages & Pages 6 & 7 n improperly installed or incorrectly adjusted door closer may cause property damage or personal injury; and will void product warranty. To avoid personal injury, O NOT ISSSML THIS LOSR OY. oor closers must be securely fastened to a properly reinforced door and frame with fasteners provided. oor closers with the HOL OPN option are not permitted to be installed in fire door assemblies. The mericans with isabilities ct () requires that doors having door closers have an opening force not to exceed 5 lbf. Use standard templating for regular arm and parallel arm applications. Jamb mounted applications use the template for 0 door opening to achieve the required opening force. The door closer's power size adjustment feature may require adjustment to its lowest setting to comply with opening force guidelines. n auxilary door stop, by others, is strongly recommended to avoid damage to the door closer and adjacent property. oors should be hung on ball bearing or anti-friction hinges/pivots. oor closer must not be installed on the exterior of a door in an exterior wall of a building. compliant closers are: 200, 20, 220, Type of Installation Interior Regular & Top Jamb Parallel rm Size of oor &oor loser xterior In-swinging xterior Out-swinging Recommended loser Size **Max. Opening orce lbs/f RHR TO TRMIN HN O YOUR : LT HN RIHT HN LHR **NOT: These forces are for standard templating with bearing type hinges and do not account for pressure differentials and draft Rev. 07/09

2 HIN OR PIVOT L 200 Regular rm Installation Instructions Template Mark oor and Jamb (for QUIK-INSTLL bracket and arm bracket) " If top rail is (76) or greater, use the template for the QUIK-INSTLL RKT provided. If top rail is -/ (5) to 2-5/6 (75), use ROP PLT (7520) IMNSIONS denoted by. *5-/ () *5-5/ () " *0-5/ (270) / (9) -/ (2) 0 (25) Mount QUIK-INSTLL racket 2-/ (57) RKT RM LIN TOP O /2-5/ () () / (76) (76) * To obtain extra closing force add " (76) to dimensions marked. This will limit degree of door opening to 0. ROP PLT Mounting Holes () 7520 This P age (25) QUIK-INSTLL RKT 75 Mount loser ody to QUIK-INSTLL racket Regular rm MOUNTIN SPIITIONS N LOSR RKT #2- self-drilling screw. / () diameter pilot hole required for Wood pplications. NOTS: heck hand of door, see page. Right Hand pplication Shown. Left Hand Opposite. imensions given in inches (mm). o Not Scale rawing. loser must be installed in atrue horizontal plane to ensure proper closer performance. oor opening (up to 0 ) is dependent upon door, frame, wall and hinge/pivot conditions permitting. Minimum clearance required over door: Non-Hold Open: -/2 (9) Hold Open: -/6 () Next Page() THIKNSS -/ (5) -/ () & OVR / SX NUT LNTH L -9/2 () -2/2 (2) L /-20 THR rill thru 9/2 (7) nlarge to / ia. This Side Only ( Places) }or{ Sex nuts, furnished when ordered Start the four mounting screws into the four closer mounting holes. Place the closer onto the QUIK-INSTLL bracket with the four mounting screws inserted into the four QUIK-INSTLL bracket slots. Tighten the four mounting screws to fasten the closer body to the QUIK-INSTLL bracket. #2- X -/2 H SL-RILLIN () OR /-20 X / HMS W/ SX NUTS () #2-2 x 5/ HMS () Rev. 07/09 2

3 200 Regular rm Installation Instructions ttach rm racket to rame NON-HOL OPN ONLY: Previous Page(2) 2 This Page HOL OPN ( OPTION ONLY): Pivot (away from hinge) #2- X -/2 H SL-RILLIN (2) Standard Position Normal mounting position. Position with pivot point away from hinge. way from hinge or dditional 5% losing orce Reposition arm mounting bracket so that pivot point is toward hinge. Hinge OR MXIMUM POWR Position rm on loser NON-HOL OPN ONLY: Main arm projects straight out at 90 angle to door. Install and tighten arm screw &washer assembly. OR RULR POWR HOL OPN : Position so that dial screw is on UNRSI of bracket HOL OPN ONLY: IL Main arm projects straight out at 90 angle to door. Remove arm screw and washer from elbow joint and disassemble arm. Thread the rod into the rm racket as shown below. Install and tighten arm screw &washer. 5/6 HX H &WSHR SSMLY MIN RKT MIN THR RO Preload and djust rm NON-HOL OPN ONLY: Open door and slide arm rod into arm loop. lose door, swing arms so adjusting arm is 90 to frame. With 7/6" wrench INSTLL and TIHTN SURLY. HOL OPN ONLY: While door is closed, adjust the Threaded rm in the rm racket until the bearing fits back onto the elbow joint on the Main rm at 90 as shown below. R-INSTLL N TIHTN SURLY. RO TU 90 xtended Maintenance Lubricate rm periodically at shaded points withadrop or two of appropriate lubricant. NOT: When lubricating a Hold Open rm, O NOT use any lubricant on the Holding Surface components. MIN THR 90 djust oor loser: See Page Rev. 07/09

4 Template 20 Parallel rm Installation Instructions This P age Mark oor and Jamb (for QUIK-INSTLL and adapter plate) If top rail is 5-/ () or greater, use the template for the QUIK-INSTLL RKT provided. If top rail is -/ () to 5-/, use ROP PLT (7525) IMNSIONS denoted by. 2-/ (70) *-/ (206) 5/ (6) L Next Page(5) 5 H I SPR LOK (When required) RM Parallel rm RM STOP RM STOP TOP O / (6) P PTR PLT -/2 () 5/ (6) L HIN OR PIVOT PTR PLT 5/ R. (6) NOTS: heck hand of door, see page Right Hand pplication Shown. Left Hand Opposite. /2 () / (25) QUIK-INSTLL RKT 75 (76) -/ (2) 0 (25) (76) *-/ (79) -/6 (7) *-/2 (9) * To obtain extra closing force add (77) to dimensions marked. This will limit degree of door opening to 0. MOUNTIN SPIITIONS N LOSR RKT #2- self-drilling screw. / () diameter pilot hole required for Wood pplications. Mount QUIK-INSTLL racket }or{ Sex nuts, furnished when ordered #2- X -/2 H SL-RILLIN () OR /-20 X / HMS W/ SX NUTS () imensions given in inches (mm). o Not Scale rawing. loser must be installed in a true horizontal plane to ensure proper closer performance. oor opening (up to 0 ) is dependent upon door, frame, wall and hinge/pivot conditions permitting. / L /-20 THR rill thru 9/2 (7) nlarge to / ia. This Side Only ( Places) THIKNSS -/ (5) -/ () & OVR SX NUT LNTH L -9/2 () -2/2 (2) Mount loser ody to QUIK-INSTLL racket Start the four mounting screws into the four closer mounting holes. Place the closer onto the QUIK-INSTLL bracket with the four mounting screws inserted into the four QUIK-INSTLL bracket slots. Tighten the four mounting screws to fasten the closer body to the QUIK-INSTLL bracket. ountersunk Holes (x) #2-2 x 5/ HMS () Rev. 07/09

5 20 Parallel rm Installation Instructions Mount dapter Plate racket on Jamb Previous Page() H I This Page Mount rm racket NON-HOL OPN : HOL OPN ONLY ( Option) /-20 X /2 POHMS WITH PTH (2) IL #2- X -/2 H SL-RILLIN () Using holes spotted on soffit or stop in Step mount adapter plate bracket. Pivot point must be WY from hinge edge of door. Position rm onto loser Using hex wrench provided, turn closing speed and latching speed valves clockwise until completely closed. O NOT OVR TIHTN. Using wrench, turn under side of spindle 5 toward the closer tube until it reaches the diamond position (fig. 2). Immediately place arm on spindle so that it is parallel to the closer body. Install and tighten arm screw and washer assembly. Reopen valves. WY ROM HIN O Install with dial screw facing down. 5/6 Hex Head Screw &Washer ssembly loser Tube ig. ig. 2 Square position t rest iamond position Rotated 5 onnect and Position rms Open door and slide arm rod into arm loop. lose door, swing arms so that they form a V position, as in Step. With 7/6" wrench, INSTLL N TIHTN SURLY. Rotate 5 HOL OPN ONLY Remove main arm screw from elbow joint and disassemble arm. Thread the rod into the rm racket as shown below. While door is closed, adjust the Threaded rm in the rm racket until the bearing fits back onto the elbow joint on the Main rm and forms a"v" as shown below. R-INSTLL N TIHTN SURLY. H TU RO Power djustment To increase the power of the closer, re-adjust the arm so it is nearer the door. To decrease power, re-adjust the arm so it is farther away from the door and then secure screw in arm loop (non-hold open) or elbow joint (hold open). THR MIN RKT xtended Maintenance Lubricate rm periodically at shaded points with a drop or two of appropriate lubricant. NOT: When lubricating a Hold Open rm, O NOT use any lubricant on the Holding Surface components. -0 (76) MX. MINIMUM POWR -/2 () MIN. MXIMUM POWR Rev. 07/09 I djust oor loser: See Page 5

6 220 Jamb Mount Installation Instructions Template This P age Mark oor and Jamb (for QUIK-INSTLL bracket and adapter plate) use dimensions in template below. O NOT US THIS TMPLT WITHROP PLT (752). Use the template addendum ( ) included with 752 rop Plate orders. Next Page(7) 7 ILIN LIN Jamb Mount (25) RKT QUIK-INSTLL RKT 75 0 (25) RM STOP TOP O 2-/ (57) MOUNTIN SPIITIONS N LOSR RKT #2- self-drilling screw. / () diameter pilot hole required for Wood pplications. Mount QUIK-INSTLL racket to Jamb }or{ Sex nuts, furnished when ordered TOP O RM / MIN. L MIN. /-20 THR OPNIN MXIMUM HR WITH STNR NRROW rill thru 9/2 (7) nlarge to / ia. This Side Only ( Places) 6-7/ (75) 5-/ -/ (6) 5-/ -/2 () -7/ () THIKNSS -/ (5) (56) 2-/2 () 0-/2 (267) 2-/ () / (9) / HIN ONITION 2-/ (60) -/ (5) SX NUT LNTH L -9/2 () -2/2 (2) utts, Offset Pivots, and Swing lear Hinges * NTR HUN imensions and are taken from centerline of hinge as shown and apply to pivot point of swing clear hinges. Offset and center hung pivots. *Must be single acting door. NOTS: -/ () heck hand of door, see page. & OVR Right Hand pplication Shown. Left Hand Opposite. imensions given in inches (mm). o Not Scale rawing. loser must be installed in atrue horizontal plane to ensure proper closer performance. ll degrees of door opening are dependent upon door, frame, wall and hinge/pivot conditions permitting. #2- X -/2 H SL-RILLIN () (02) -/2 (9) Mount loser ody to QUIK-INSTLL racket Start the four mounting screws into the four closer mounting holes. Place the closer onto the QUIK-INSTLL bracket with the four mounting screws inserted into the four QUIK-INSTLL bracket slots. Tighten the four mounting screws to fasten the closer body to the QUIK-INSTLL bracket Rev. 07/09 6

7 ttach rm racket to oor NON-HOL OPN ONLY: Standard Position Normal mounting position. Position with pivot point away from hinge. 200 Jamb Mount Installation Instructions Previous Page(6) 6 This Page HOL OPN ( Option): #2- X -/2 H SL-RILLIN (2) OR /-20 X/ HMS W/ SX NUTS (2) way from hinge or dditional 5% losing orce Reposition arm mounting bracket so that pivot point is toward hinge. Hinge Pivot (away from Hinge) RM STOP OR RULR POWR OR MXIMUM POWR Position rm on loser NON-HOL OPN ONLY: Main arm projects straight out at 90 angle to door. Install and tighten arm screw & washer assembly. 5/6 HX H &WSHR SSMLY MIN Install with dial screw facing down IL HOL OPN ONLY ( Option): Main arm projects straight out at 90 angle to door. Install and tighten arm screw &washer assembly. Remove main arm screw from elbow joint and disassemble arm. Thread the rod into the rm racket as shown below. RKT THR RO 5/6 HX H &WSHR SSMLY MIN Preload and djust rm NON-HOL OPN ONLY: Open door and slide arm rod into arm loop. lose door, swing arms so adjusting arm is 90 to frame. With 7/6" wrench, INSTLL and TIHTN SURLY. HOL OPN ONLY ( Option): While door is closed, adjust the Threaded rm in the rm racket until the bearing fits back onto the elbow joint on the Main rm at 90 as shown below. R-INSTLL and TIHTN SURLY. 90 RO LOOP xtended Maintenance Lubricate rm periodically at shaded points with a drop or two of appropriate lubricant. NOT: When lubricating a Hold Open rm, O NOT use any lubricant on the Holding Surface components. RKT THR 90 MIN djust oor loser: See Page Rev. 07/09 7

8 000 Installation Instructions - loser djustment Spring Power djustment Locate spring power adjuster from Illustration below 200 Size thru 6 djustment See hart 200 SPRIN POWR JUSTMNT HRT ll 200 closers are factory set at an approximate Size. djust closer as necessary for door size using this chart. Readjustment may be required to suit prevailing conditions. Interior 2 (72) 2 6 (76) 0 (95) 6 (067) Size of oor xterior In Swing xterior Out Swing 2 6 (76) ' 0 " (95) ' 6 " (067) 2' 6 " (76) (29) 0 (95) Spring Power djustment No. ull Turns lockwise Regular & TJ Mounting Parallel rm Mounting quivalent loser Size (pprox.) 5 6 ate Stamp (on end of closer) MM-YY MM =Month YY =Year LTHIN SP VLV OPTION M7 LY TION VLV LOSIN SP VLV KHK INTNSITY VLV SPRIN POWR JUSTR (/ LLN WRNH) " Latch losing Speed elayed ction Option M7 losing Speed Valve To adjust speed of door closing from fully open to a position 2" to 5" from closed, turn losing Speed Valve LOKWIS to SLOW closing, OUNTR-LOKWIS to SP closing. Latching Speed Valve fter closing speed has been obtained, turn latching speed valve LOKWIS to SLOW latching or OUNTR-LOKWIS to SP latching for last 2" to 5" of door travel. NOT: Set combination of LOSIN and LTHIN speeds to between and 7 seconds Use of door by handicapped, elderly or small children may require even greater closing time. elayed ction Valve ackcheck (/ llen Wrench Provided) (/ llen Wrench Provided) (/ llen Wrench Provided) Turn valve LOKWIS to SLOW closing, OUNTR- LOKWIS to SP closing. elayed action may be adjusted from 20 seconds to 90 seconds, depending on degree of door swing. elay occurs at the beginning of the door closing cycle from fully open down to 70, where the closing speed valve then begins its control. ackcheck Intensity Valve Turn valve OUNTR-LOKWIS to reduce backcheck or LOKWIS to increase backcheck. (ackcheck should be set to give a soft cushioning action, not a sudden stop.) Installing over Slip cover over closer. Hold tightly against QUIK-INSTLL racket surface. Secure on each side with 6-2 x /" PHMS screws. Insert is removable. Place in unused opening. Plastic over (Standard) To djust Hold Open ( Option) Open the door to desired position and tighten the hold open screw firmly (or RH application, turn screw on underside LOKWIS. or LH application, turn screw OUNTR- LOKWIS.) Place the hold open dial over the hex head of the bracket screw so that one of the slots in the dial is directly over small screw hole tapped in bracket. Seat the dial tightly over the bracket. INSRT IL N TIHTN SURLY Rev. 07/09 IL HOL OPN opyright 2006, 2009, orbin Russwin, Inc., an SS LOY roup company. ll rights reserved. Reproduction in whole or in part without the express written permission of orbin Russwin, Inc. is prohibited. IL