Installation Instructions. Hold Open Arm Models. Sized (Sizes 2,3,4,5) Weaker BC-H 9303BC-H 9304BC-H 9305BC-H

Transcription

1 O Regular rm ee Page Instructions Hold Open rm Models tronger ized (izes,,4,5) 90H 90H 904H 905H 900H eries Non Handed loser O Regular rm Top Jamb Parallel rm Regular rm ee Page eft Hand H Right Hand Reverse RHR UTION n Incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These installation instructions should be followed to avoid the possibility of misapplication or misadjustment. UTION Right Hand RH eft Hand Reverse HR eft Hand H Right Hand Reverse RHR eft Hand H Right Hand Reverse RHR Top Jamb ee Page 5 Parallel rm ee Pages & 4 NOTE: For special applications a separate door and frame preparation template is packed with these instructions. Use this instruction sheet for installation sequence and closer adjustments only. s should be hung on ball bearing or antifriction hinges. separate door stop is recommended. and frame must be properly reinforced. djust closing time speed between and 7 seconds from 90 to 0. These door closers should NOT be installed on the exposed side (weather side) of exterior doors. Top Jamb ee Page 5 Right Hand RH eft Hand Reverse HR Parallel rm ee Pages & 4 Right Hand RH eft Hand Reverse HR elf Drilling crews Wood and Metal (Optional) leeve Nut and olt #7 /1" Metal 1/40 tandard omponents Wood For Wood drill /1 hole Machine crews #7 Drill, 1/40 Tap Drill 9/ thru from loser ide /8 Drill other side Thru olt and Grommet Nut Drill 9/ thru from loser ide /8 Drill other ide Optional omponents loser ody Main rm 988 Plate 14 loser ize tamp ""Valve ""Valve et crew rm ssembly offit dapter Plate 98H offit Plate Used with Parallel rm losers Only opyright 005, 014 ale ecurity Inc., an O Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of ale ecurity Inc. is prohibited (0514)

2 900H eries Hold Open losers Regular rm O Parts 1 11/4 () (15) 1/4 (44) /4 (19) 91/1 (0) Right Hand hown 7/8 () D R eft Hand Nut Down Inches (mm) Opening To to to 180 Dimension "" 7 (178) (15) 1/ (89) /Wall/Hardware/Jamb conditions permitting weep 4 5 atch F 90 E ackcheck et Hold Open 7 8 tronger 90 min. Don't completely close valve crew pinion cap onto pinion shaft by hand or with a Phillips screw driver DO NOT OVER TIGHTEN. opyright 005, 014 ale ecurity Inc., an O Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of ale ecurity Inc. is prohibited (0514)

3 900H eries Hold Open losers Parallel rm O Parts 1 /4 Right Hand hown (70) /8 (10) (50) 7/1 (11) 1/ (1) Opening To to to /4 (5) 7/4 (197) 5/4 (14) 988 Plate Optional 75/8 (194) 1/8 (15) 41/8 (105) /Wall/Hardware/Jamb conditions permitting 85/8 (19) 71/8 (181) 51/8 (10) Holes for 988 Plate only Inches (mm) Top of 7 (178) 4 (10) 11/ (8) 1/8 Frame (54) 1/4 (8) 1/ (1) /4 91/1 (19) (0) lose Valves 4 5 weep eft Hand Right Hand Down Up Place rm on pindle atch Rotate Remove rm from pindle opyright 005, 014 ale ecurity Inc., an O Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of ale ecurity Inc. is prohibited. ee tep on Page (0514)

4 900H eries Hold Open losers Parallel rm O Open Valves 7 ssemble rm 8 Right Hand eft Hand Flat or R R Flat Do Not ack Valves Out ompletely rm crew 9 weep 10 atch 11 11/ (8) rm crew ackcheck 1 1 et Hold Open 14 tronger Don't completely close valve crew pinion cap onto pinion shaft by hand or with a Phillips screw driver DO NOT OVER TIGHTEN. opyright 005, 014 ale ecurity Inc., an O Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of ale ecurity Inc. is prohibited (0514)

5 R 900H eries Hold Open losers Top Jamb rm Parts 1 91/1 (0) /4 (19) O Top of 11/ (8) 1/4 (44) (15) 1/ (1) E 90 Inches (mm) Opening To to to 180 Right Hand hown /Wall/Hardware/Jamb conditions permitting Dimension "" 71/ (191) (15) 1/ (89) longer connecting rod is required for reveals greater than " (7) Reveal weep 4 atch 5 eft Hand Nut Up D F ackcheck tronger et Hold Open 7 8 crew pinion cap onto pinion shaft by hand or with a Phillips screw driver DO NOT OVER TIGHTEN. Don't completely close valve 70 to 180 opyright 005, 014 ale ecurity Inc., an O Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of ale ecurity Inc. is prohibited (0514)

6 900H eries djustments weep atch O (Use 1/8" Hex Wrench for these djustments) ackcheck tronger OED To identify your model: To et Hold Open Open to Desired ngle Use 1" Wrench ize ode 4 G Date ode =90H =90H 4=904H 5=905H opyright 005, 014 ale ecurity Inc., an O Group company. ll rights reserved. Reproduction in whole or in part without the express written permission of ale ecurity Inc. is prohibited. O 000 Highway 74 East Monroe, N 811 Tel: (877) Fax: (800) (0514)