SURROUND STEP ASSEMBLY INSTRUCTIONS

Transcription

1 ASSEMLY INSTRUCTIONS SURROUND STEP Toll Free:

2 efore You egin SURROUND STEP IMPORTANT READ ALL INSTRUCTIONS EFORE STARTING ASSEMLY. UNPACKAGE PARTS AND HARDWARE AND LOCATE ALL PIECES. TOOLS REQUIRED FOR ASSEMLY ESTIMATED ASSEMLY TIME: 1.5 HOURS SITE PREPARATION INSTALL ON A FIRM, LEVEL SURFACE TO KEEP THE PRODUCT CLEAN AND SCRATCH FREE DURING SETUP LAY A TARP ON WORK SURFACE TO PROTECT THE PRODUCT. POWER DRILL TWO PERSON PROJECT PRODUCT IS HEAVY USE CARE WHEN LIFTING QUESTIONS? FOR ADDITIONAL INFORMATION PLEASE CALL OR TO THE NUMERS OR ADDRESS ELOW. PLEASE HAVE SERIAL NUMER READY TO ENSURE QUICK SERVICE. support@visscherspecialty.com TOLL FREE TEL: INTERNATIONAL TEL:

3 Components PARTS INVENTORY Components SURROUND STEP 1 X TOP CORNER TREAD PANEL DEALER CODE: X STRINGERS DEALER CODE: X OTTOM CORNER TREAD PANE DEALER CODE: X RACKETS DEALER CODE: 1987 Hardware Pack A 15 X 1 1/4" #8 FLAT HEAD (#2 Robertson) 4 X TREAD PANELS DEALER CODE: 1983 C 50 X 2 1/2" #8 FLAT HEAD (#2 Robertson) 10 X 3 1/2" #10 FLAT HEAD (#2 Robertson) 1 x ROERTSON IT

4 Step One: Layout SURROUND STEP TAKE TWO TREAD PANELS (DC 1983) AND LAY THEM FACE DOWN AS SHOWN. DC: 1983 DC: 1983

5 Step Two: Attach Stringers SURROUND STEP DEALER CODE 1980 PLACEMENT OF STRINGER DC: 1980 DEALER CODE 1980 DEALER CODE 1980 DEALER CODE 1980 LOCATOR MARKINGS DEALER CODE 1980 DEALER CODE 1980 PLACE THE THREE STRINGERS ON EACH TREAD PANEL USEL LOCATOR MARKINGS TO DETERMINE LOCATIONS OF STRINGERS. SCREW THROUGH PILOT HOLES FOUND ON STRINGERS. STRINGER TO E FLUSH WITH THIS SURFACE STRINGER DETAIL 1 LOCATOR MARKINGS LOCATOR MARKINGS TREAD PANEL HALF ON TREAD MIDDLE OF TREAD TIGHT TO TREAD PANEL PANEL PANEL END CAP 20 X 2 1/2" ROERTSON SCREWS

6 Step Three: Attach rackets SURROUND STEP DO THIS PROCESS FOR OTH ASSEMLIES ALIGN AND FLUSH RACKET EDGE WITH STRINGER ALIGN AND FLUSH RACKET EDGE WITH STRINGER DC: 1987 DC: 1987 ATTACH TWO RACKETS (DC:1987) TO EACH TREAD PANEL ASSEMLY AT THE LOCATIONS SHOWN AOVE. ALIGN AND FLUSH A FLUSH A 12 X 1 1/4" ROERTSON SCREWS

7 Step Four: Flip Assemblies SURROUND STEP DO THIS PROCESS FOR OTH ASSEMLIES FLIP OTH ASSEMLIES ONTO THERE ACKS AS SHOWN.

8 Step Five: Attach ottom Tread Panels SURROUND STEP DO THIS PROCESS FOR OTH ASSEMLIES DC: 1983 PLACEMENT OF OTTOM TREAD PANELS (DC: 1983 ) SCREW THROUGH THE PILOT HOLES ON THE STRINGERS INTO THE TREAD PANELS. 20 X 2 1/2" ROERTSON SCREWS

9 Step Six: Set Assemblies In Place SURROUND STEP ASSEMLIES WILL E HEAVY. USE CAUTION WHEN PERFORMING THIS STEP. FLIP THE ASSEMLIES RIGHT-SIDE UP AND ESIDE THE HOT TU

10 Step Seven: Assemble ottom Corner SURROUND STEP LOCATOR MARKINGS DETAIL 1 STRINGER VIEW FROM SIDE Y X DC: 1986 VIEW FROM TOP DC: 1980 EQUAL EQUAL X Y PLACEMENT OF OTTOM CORNER TREADS DC: TAKE THE STRINGER (DC 1980) AND PLACE IT ON ITS ACK EDGE. PLACE THE OTTOM CORNER TREAD PANEL (DC 1986) ON THE STRINGER USING THE LOCATOR MARKING FOR ALIGNMENT. OTTOM CORNER TREAD PANEL DC: 1986 STRINGER DC: X 2 1/2" ROERTSON SCREWS

11 Step Eight: Dry-Fit all pieces SURROUND STEP DIAGRAM 8A PLACE THE OTTOM CORNER TREAD AND STRINGER ASSEMLY IN ETWEEN THE STEP ASSEMLIES. ADJUST PLACEMENT TO ACHIEVE EQUAL SPACING ETWEEN TREADS. DIAGRAM 8A DIAGRAM 8 PLACE THE TOP CORNER TREAD PANEL (DC 1984) ON TOP OF STEP ASSEMLIES. ADJUST PLACEMENT TO ACHIEVE EQUAL SPACE ETWEEN TREADS. DIAGRAM 8

12 Step Nine: Fasten Assemblies Togeher SURROUND STEP INSTALL SCREWS THROUGH PILOT HOLES INTO STRINGERS INSTALL SCREWS SLIGHTLY ELOW THE SURFACE OF THE TREAD TO PREVENT INJURY DURING USE. C 8 X 3 1/2" ROERTSON SCREWS

13 ASSEMLY INSTRUCTIONS HOT TU AR Toll Free:

14 efore You egin HOT TU AR IMPORTANT READ ALL INSTRUCTIONS EFORE STARTING ASSEMLY. UNPACKAGE PARTS AND HARDWARE AND LOCATE ALL PIECES. TOOLS REQUIRED FOR ASSEMLY ESTIMATED ASSEMLY TIME: 45 MINUTES SITE PREPARATION INSTALL ON A FIRM, LEVEL SURFACE TO KEEP THE PRODUCT CLEAN AND SCRATCH FREE DURING SETUP, LAY A TARP ON WORK SURFACE TO PROTECT THE PRODUCT. POWER DRILL TWO PERSON PROJECT PRODUCT IS HEAVY USE CARE WHEN LIFTING QUESTIONS? FOR ADDITIONAL INFORMATION PLEASE CALL OR TO THE NUMERS OR ADDRESS ELOW. PLEASE HAVE SERIAL NUMER READY TO ENSURE QUICK SERVICE. support@visscherspecialty.com TOLL FREE TEL: INTERNATIONAL TEL:

15 Components PARTS INVENTORY Components HOT TU AR 3 X AR LEG DEALER CODE: X CORNER TREAD PANEL WITH END DEALER CODE: X RACKETS DEALER CODE: 1987 Hardware Pack A 10 X 1 1/4" #8 FLAT HEAD (#2 Robertson) 1 X TREAD PANELS DEALER CODE: X 2 1/2" #8 FLAT HEAD (#2 Robertson) 1 x ROERTSON IT 2 X SUPPORTS DEALER CODE: 1989

16 Step One: Layout HOT TU AR TAKE THE TREAD PANEL WITH END (DC 1983) AND CORNER TREAD PANEL (DC 1988) AND LAY THEM FACE DOWN. DC: 1983 DC: 1988

17 Step Two: Attach ar Legs HOT TU AR PLACEMENT OF AR LEGS DC: 1985 PLACE THE THREE AR LEGS ON EACH TREAD PANEL DC: 1983 USEL LOCATOR MARKINGS TO DETERMINE LOCATIONS OF THE AR LEGS. SCREW THROUGH PILOT HOLES FOUND ON THE AR LEGS. STRINGER TO E FLUSH WITH THIS SURFACE DC: 1983 DC: 1983 LOCATOR MARKINGS 12 X 2 1/2" ROERTSON SCREWS HOTTU AR

18 Step Three: Attach rackets HOT TU AR ALIGN AND FLUSH RACKET EDGE WITH AR LEGS ALIGN AND FLUSH RACKET EDGE WITH AR LEGS DC: 1987 DC: 1987 ATTACH TWO RACKETS (DC:1987) TO EACH TREAD PANEL ASSEMLY AT THE LOCATIONS SHOWN AOVE. ALIGN AND FLUSH A FLUSH A 6 X 1 1/4" ROERTSON SCREWS

19 Step Three: Attach rackets HOT TU AR ALIGN AND FLUSH RACKET EDGE WITH AR LEGS ALIGN AND FLUSH RACKET EDGE WITH AR LEGS DC: 1987 DC: 1987 ATTACH TWO RACKETS (DC:1987) TO EACH TREAD PANEL ASSEMLY AT THE LOCATIONS SHOWN AOVE. ALIGN AND FLUSH A FLUSH A 6 X 1 1/4" ROERTSON SCREWS

20 Step Five: ar in Place HOT TU AR ASSEMLIES WILL E HEAVY. USE CAUTION WHEN PERFORMING THIS STEP. FLIP AR ASSEMLY UPRIGHT AND PLACE AROUND HOT TU.

21 ASSEMLY INSTRUCTIONS 28" STOOL Toll Free:

22 ASSEMLY INSTRUCTIONS 28" STOOL IMPORTANT TOOLS REQUIRED FOR ASSEMLY READ ALL INSTRUCTIONS EFORE STARTING ASSEMLY. UNPACKAGE PARTS AND HARDWARE AND LOCATE ALL PIECES. ESTIMATED ASSEMLY TIME: 30 MINUTES SITE PREPARATION POWER DRILL INSTALL ON A FIRM, LEVEL SURFACE TO KEEP THE PRODUCT CLEAN AND SCRATCH FREE DURING SETUP, LAY A TARP ON WORK SURFACE TO PROTECT THE PRODUCT. QUESTIONS? FOR ADDITIONAL INFORMATION PLEASE CALL OR TO THE NUMERS OR ADDRESS ELOW. PLEASE HAVE SERIAL NUMER READY TO ENSURE QUICK SERVICE. TAPE MEASURE support@visscherspecialty.com TOLL FREE TEL: INTERNATIONAL TEL: PENCIL Toll Free:

23 Components PARTS INVENTORY 1 X SEAT DEALER CODE: 1990 Hardware Pack 28" STOOL 20 X 2 1/2" #8 FLAT HEAD (#2 Robertson) 1 x ROERTSON IT 2 X A-FRAME STOOL LEG DEALER CODE: X SMALL RACE DEALER CODE: X LARGE RACE DEALER CODE: 1991

24 STOOL ASSEMLY 28" STOOL Step 1 DC: 1992 DC: 1993 Step 2 DC: 1992 DC: " DC: 1993 DC: X 2 1/2" ROERTSON SCREWS

25 STOOL ASSEMLY 28" STOOL Step 3 Step 4 DC: 1990 LIFT FARIC SKIRT TO ACCESS SCREW LOCATIONS DC: 1990 DC: X 2 1/2" ROERTSON SCREWS