JASPER INSTRUCTIONS CODE: 0097 CODE: 0197 TOLL FREE/SANS FRAIS: _Jasper_11x11_Instructions_V1.2. Front Elevation.

Transcription

1 INSTRUCTIONS JASPER CODE: 0097 CODE: ' " [363 cm] 10'-8 1 2" [326 cm] WINDOW WINDOW WINDOW WINDOW WINDOW 9' " [285 cm] WINDOW WINDOW WINDOW WINDOW 10'-8 1 2" [326 cm] 11' " [363 cm] WINDOW SINGLE DOOR WINDOW Front Elevation Footprint Plan 0097_Jasper_11x11_Instructions_V1.2 EN TOLL FREE/SANS FRAIS:

2

3 PANELS / PANNEAUX PAGE OF DE PARTS - PIÈCES 1 1 CODE: 0097 JASPER CODE: 0197 ROOFING PARTS / PIÈCES DE TOITURE 3'-4" 3'-4" 2'-11" 2'-11" 1X 11X 11X 11X 4X 4X '-1" 7'-10" *Optional/Optionnel 4X '-2" X '-2" TRUSS FRAME / FERME DE TOIT 4X 4X '-8" 6'-3" 4X 4X 4X 4X '-10" 6'-7" 6'-6" 7'-2" 4X X 2X 2X '-1" 3'-9" 3'-0" 3'-6" ROOFING / TOITURE 3'-7" 3'-6" 4'-10" 4'-10" 4X 4X 4X 4X 1X 3'-6" _Jasper_11x11_Instructions_V1.2 MEASUREMENTS ARE APPROXIMATE MESURES SONT APPROXIMATIVES TOLL FREE/SANS FRAIS:

4

5 HARDWARE JASPER CODE: 0097 CODE: X ROBERTSON BIT/ EMBOUT ROBERTSON A 12X 1 1/2" #8 FLAT HEAD (#2 ROBERTSON) 1 ½ PO À TÊTE PLATE NO 8 (no 2 ROBERTSON) 1X 1/4" HEX HEAD BIT/ EMBOUT À TÊTE HEXAGONALE DE 1/4 PO B C 157X 24X 2 1/2" #8 FLAT HEAD (#2 ROBERTSON) 2 ½ PO À TÊTE PLATE NO 8 (no 2 ROBERTSON) 3 1/2" #10 FLAT HEAD (#2 ROBERTSON) 3 ½ PO À TÊTE PLATE no 10 (no 2 ROBERTSON) 1X INSTRUCTION MANUAL / MANUEL D'INSTRUCTION F I 80X 184X 2 1/2" PAN HEAD ROBERTSON SCREWS (#2 ROBERTSON) 2 ½ PO À TÊTE TRONCONIQUE no 8 (no 2 ROBERTSON) 1X " #10 METAL ROOF SCREW (1/4" HEAD) 1 PO TOITURE DE METAL no 10 (TETE DE ¼ po) 16X X 2008 J L 16X 4X 1 1/2" #10 ROOF SCREW (1/4" HEAD) WITH POLYZIP WASHER 1 ½ PO VIS À TOITURE no 10 (TÊTE DE ¼ po) REQUISES AVEC RONDELLES POLYZIP 2 1/2" SCREW #8 HEX HEAD (1/4" HEAD) 2 ½ PO À TÊTE HEXAGONALE no 8 (TÊTE DE ¼ po) 1X 2033 M 32X 3" SCREW #8 HEX HEAD (1/4" HEAD) 3 PO À TÊTE HEXAGONALE no 8 (TÊTE DE ¼ de po) 0097_Jasper_11x11_Instructions_V1.2 TOLL FREE/SANS FRAIS:

6

7 IMPORTANT JASPER CODE: 0097 CODE: 0197 TOOLS NEEDED BEFORE YOU BEGIN POWER DRILL THESE INSTRUCTIONS MUST BE FOLLOWED STEP BY STEP. DEVIATION FROM THE INSTRUCTIONS MAY VOID THE PRODUCT'S WARRANTY. SEE WARRANTY SHEET FOR FURTHER DETAILS. READ ALL INSTRUCTIONS THOROUGHLY BEFORE STARTING ASSEMBLY. TAPE MEASURE USE THE PARTS LIST AS A CHECKLIST FOR COMPONENTS. UNWRAP PARTS ONLY AS NEEDED TO KEEP COMPONENT DEALER CODE LABEL INTACT FOR REFERENCE. PENCIL TWO PERSON PROJECT PRODUCT CAN BE HEAVY RUBBER MALLET USE CARE WHEN LIFTING SITE PREPARATION LADDER (8ft / 2.5m) ASSEMBLE THE STRUCTURE ON A FIRM, LEVEL SURFACE. PROTECT THE PRODUCT FROM DAMAGE AS SOME PIECES MAY BE FRAGILE. ESTIMATED ASSEMBLY TIME: 6 HOURS PHILLIPS SCREW DRIVER IF YOU REQUIRE ASSISTANCE, OR NEED TO ORDER REPLACEMENT PARTS, CONTACT YOUR VISSCHER DEALER. FOR ADDITIONAL INFORMATION PLEASE CALL THE NUMBER BELOW. PLEASE HAVE SERIAL NUMBER READY TO ENSURE QUICK SERVICE. KNIFE 0097_Jasper_11x11_Instructions_V1.2 EN TOLL FREE/SANS FRAIS:

8

9 Step One ATTACH TOGETHER ONE RIGHT TRUSS FRAME PIECE (DC 1352) AND ONE LEFT TRUSS FRAME PIECE (DC 1351). THE COMPONENTS SHOULD BE FIT AS TIGHTLY TOGETHER AS POSSIBLE. REPEAT TO BUILD A TOTAL OF FOUR TRUSS FRAME LENGTHS. DC-1352 DC-1351 C 3 1/2" ROBERTSON SCREWS 24 req

10 Step Two FLIP THE FOUR TRUSS FRAME LENGTHS OVER AND LAY THEM OUT TO FORM A SQUARE. ATTACH THE CORNERS TOGETHER AS SHOWN IN DIAGRAM 1. FASTEN ALL FOUR CORNERS IN THE SAME FASHION. TRUSS FRAME LENGTH TRUSS FRAME LENGTH TRUSS FRAME LENGTH DIAGRAM 1 THE TRUSS FRAME ASSEMBLY MUST BE SQUARE MEASURE THE TRUSS FRAME TO VERIFY SQUARENESS. THE MEASUREMENT FROM "A" TO "D" MUST EQUAL "B" TO "C". ADJUST THE TRUSS FRAME UNTIL BOTH MEASUREMENTS ARE EQUAL. A TO D = B TO C TRUSS FRAME LENGTH 2 1/2" ROBERTSON SCREWS 12 req B

11 Step Three ATTACH FOUR TRUSS FRAME BRACES (DC-1304). KEEP THE BRACES TIGHT TO THE BOTTOM PLATE. THIS STEP COMPLETES THE TRUSS FRAME. DC-1304 DC-1304 THE TRUSS FRAME ASSEMBLY MUST REMAIN SQUARE. DOUBLE CHECK CORNER-TO-CORNER MEASUREMENTS ONCE BRACES ARE ATTACHED. DC-1304 MAKE REFERENCE MARKS LAY THE SQUARED TRUSS FRAME ASSEMBLY AT THE EXACT LOCATION YOU WISH YOUR GAZEBO TO BE. USING A PENCIL OR MARKER, TRACE THE OUTSIDE EDGES OF ALL FOUR CORNERS ONTO THE GROUND. THESE MARKINGS WILL BE HELPFUL IN PLACING YOUR CORNER POSTS AND PANELS IN THE STEPS TO COME. ONCE MARKINGS ARE COMPLETE, MOVE THE TRUSS FRAME UP AND OUT OF THE WAY. DC-1304 B 2 1/2" ROBERTSON SCREWS 16 req 0097_Jasper_11x11_Instructions_V1.2 EN

12 OPTIONAL BAY KIT IF YOU HAVE PURCHASED AN OPTIONAL BAY WALL KIT FOR YOUR OUTDOOR STRUCTURE, PLEASE MOVE ON TO STEP ONE OF THE INSTRUCTIONS PROVIDED WITH THE BAY KIT AT THIS TIME.

13 Step Four ATTACH TWO WALL PANELS (DC 1971) TO EACH CORNER POST (DC 1042). NOTE THE SCREW LOCATIONS IN THE DIAGRAM. WALL PANELS ARE TO BE FLUSH WITH THE OUTSIDE OF THE POST AND FLUSH AT TOP AND BOTTOM. IF YOU WANT THE DOOR TO BE LOCATED TIGHT TO A CORNER, SUBSTITUTE A WALL PANEL FOR THE DOOR PANEL (DC 1970). MOVE ALL FOUR ASSEMBLIES TO THE GROUND REFERENCE MARKERS FROM STEP THREE. DC-1971 DC-1971 DC-1042 F 2 1/2" BLACK PAN HEAD ROBERTSON SCREWS 32 req

14 Step Five ATTACH THE REMAINDER WALL PANELS (DC 1971) AND THE DOOR PANEL (DC 1970). CONTINUE THE SAME SCREW PATTERN FROM THE PREVIOUS STEP. WALL PANELS ARE TO BE FLUSH WITH EACH OTHER AND FLUSH AT TOP AND BOTTOM. DC-1971 REFERENCE MARK REFERENCE MARK DC-1971 DC-1971 DC-1970 REFERENCE MARK REFERENCE MARK F 2 1/2" BLACK PAN HEAD ROBERTSON SCREWS 32 req

15 Step Six LIFT THE TRUSS FRAME ASSEMBLY AND CAREFULLY PLACE IT ON TOP OF THE STRUCTURE. THE OUTSIDE SURFACE OF THE WALLS ARE TO BE FLUSH WITH THE OUTSIDE OF THE TRUSS FRAME ASSEMBLY. SCREW DOWN THROUGH THE PLATE OF THE TRUSS FRAME ASSEMBLY INTO THE TOP OF EACH WALL AND DOOR PANEL. USE THREE SCREWS PER WALL PANEL AND FOUR PER DOOR PANEL. TRUSS FRAME (OUTSIDE) FLUSH WALL PANEL (OUTSIDE) SECTION VIEW 2 1/2" ROBERTSON SCREWS 37 req B

16 Step Seven BUILD THE SKYLIGHT FRAME USING FOUR SKYLIGHT PIECES (DC 1681). IT IS IMPORTANT TO "CHASE" CORNERS AS SHOWN BELOW. DC-1681 DC-1681 DC-1681 DC /2" ROBERTSON SCREWS 12 req B

17 Step Eight PLACE SKYLIGHT FRAME ON A FLAT SURFACE. ATTACH COMMON RAFTERS (DC 1675) TO THE SKYLIGHT FRAME, CENTRED ON EACH SIDE. THE BOTTOM EDGE OF THE RAFTERS ARE TO BE FLUSH WITH THE BOTTOM OF THE SKYLIGHT FRAME. DC-1675 EQ. EQ. DC-1675 DC-1675 DC-1675 DC-1675 FLUSH FLUSH DC '-8" 4'-8" SECTION VIEW 3" HEX HEAD SCREWS 8 req M

18 Step Nine FLIP SKYLIGHT FRAME AND RAFTER ASSEMBLY OVER AND PLACE ON TRUSS FRAME. CENTRE THE RAFTERS ON THE TRUSS FRAME. DO NOT FASTEN RAFTERS TO THE TRUSS FRAME AT THIS TIME. SECTION VIEW EQ EQ TOP PLAN VIEW 0097_Jasper_11x11_Instructions_V1.2 EN

19 Step Ten ATTACH HIP RAFTERS (DC 1676). THE BOTTOM EDGE OF THE RAFTER IS TO BE FLUSH WITH THE BOTTOM EDGE OF THE SKYLIGHT FRAME. DC-1676 DC-1676 DC SKYLIGHT FRAME ENDS OF RAFTER ARE FLUSH TO THE BOTTOM OF THE SUPPORT SECTION VIEW DC-1676 DC-1676 TOP PLAN VIEW M 3" HEX HEAD SCREWS 8 req

20 Step Eleven FASTEN LEFT AND RIGHT PANEL SUPPORTS (DC1570 & DC1571) TO THE TRUSS FRAME. DC-1570 DC-1571 DC-1571 DC-1570 FLUSH FLUSH DC-1570 DC-1571 DC-1570 DC-1571 SECTION VIEW DC-1571 DC /2" ROBERTSON SCREWS 32 req B

21 Step Twelve SKYLIGHT FRAME DC-1758 DC-1244 RAFTER BLOCK FRONT VIEW DC-1244 FASTEN THE SHORT ROOF STRAPPING (DC 1758) TO THE RAFTERS AND TIGHT TO THE SKYLIGHT FRAME. DC-1758 DC-1244 FASTEN THE LONG ROOF STRAPPING (DC 1244) TO THE RAFTERS AND TIGHT TO THE RAFTER BLOCK. THE ANGLE CUTS ARE TO BE FACE DOWN AND LOCATED AT THE HIP RAFTERS. DC-1244 DC-1758 DC-1758 DC-1758 DO NOT STAND ON THE TRUSS FRAME OR RAFTER ASSEMBLY DC-1244 B TOP PLAN VIEW 2 1/2" ROBERTSON SCREWS 48 req

22 Step Thirteen SECURE THE RAFTERS TO THE TRUSS FRAME. DETAIL - 1 DETAIL - 2 SECURE THE COMMON RAFTERS AS SHOWN IN DETAIL 1. DETAIL - 1 SECURE THE HIP RAFTERS AS SHOW IN DETAIL - 2. DETAIL - 2 M 3" HEX HEAD SCREWS 16 req

23 OPTIONAL BAY KIT IF YOU HAVE PURCHASED AN OPTIONAL BAY WALL KIT FOR YOUR OUTDOOR STRUCTURE, PLEASE MOVE ON TO STEP THREE OF THE INSTRUCTIONS PROVIDED WITH THE BAY KIT AT THIS TIME.

24 Step Fourteen ATTACH CLOSURE TABS (DC 1834) TO THE UNDERSIDE OF THE ROOFING SHEETS. CLOSURE TABS ARE TO BE IN-LINE WITH THE FIRST ROW OF PUNCHED SCREW LOCATIONS. TRIM CLOSURE TABS FOR NARROW ROOF PANELS. DC-1834 CLOSURE TAB DC-1834 ROOFING SHEET SECTION VIEW 0097_Jasper_11x11_Instructions_V1.2 EN

25 Step Fifteen LAY ROOFING SHEETS (DC 1835, 1854, 1855, 1856) ON ONE SIDE OF THE ROOF. MIDDLE SHEETS ARE TO BE TIGHT TO THE OUTSIDE EDGE OF THE SKYLIGHT FRAME. THE OVERHANG IS TO BE EQUAL OVER THE ENTIRE EAVE. FASTEN THROUGH PRE-PUNCHED HOLES ONLY. DC-1853 IMPORTANT: FASTEN ALL SCREWS PRIOR TO STEPPING ON ROOF. REPEAT FOR THREE SIDES OF THE ROOF AT THIS TIME. DC-1856 TIP: FASTEN ROOFING SHEETS ONLY ON THREE SIDES OF THE ROOF AT THIS TIME. DC-1855 DC-1854 THIS WILL MAKE FOR EASIER MOUNTING OF THE SKYLIGHT. FRONT VIEW TIGHT TO THE OUTSIDE EDGE OF SKYLIGHT FRAME ONLY. NOT ON TOP OF THE FRAME. I SECTION VIEW 1" ROOF SCREWS 120 req

26 Step Sixteen ASSEMBLE THE SKYLIGHT (DC 1840, 1841). L 2 1/2" HEX HEAD SCREWS 4 req

27 Step Seventeen FASTEN FOAM WEATHER GASKET (DC 1850) TO THE PERIMETER OF THE SKYLIGHT ALONG THE INSIDE EDGE. DC-1850 TRIM AS NEEDED 0097_Jasper_11x11_Instructions_V1.2 EN

28 Step Eighteen FASTEN THE ACRYLIC SKYLIGHT PANEL (DC 1842) TO THE SKYLIGHT FRAME. CAREFULLY PEEL PROTECTIVE COATING OFF BOTH SIDES OF THE ACRYLIC PANEL ALIGN THE PRE-DRILLED HOLES OF THE ACRYLIC WITH THE PRE-DRILLED HOLES OF THE SKYLIGHT FRAME. SCREWS MUST BE CENTRED IN HOLES DC-1842 THE ACRYLIC PANEL EXPANDS AND CONTRACTS AT A DIFFERENT RATE THAN THE SKYLIGHT FRAME. IF THE SHANK OF THE SCREW IS TIGHT AGAINST THE ACRYLIC PANEL, CRACKING WILL OCCUR. TAKE THE NECESSARY TIME TO PROPERLY CENTRE EACH SCREW. 90 J 1 1/2" #10 METAL ROOF SCREW (1/4" HEAD) WITH POLYZIP WASHER 2 req

29 Step Nineteen COMPLETELY FASTEN THE ACRYLIC PANEL TO THE SKYLIGHT FRAME USING THE PRE-DRILLED HOLES. SCREWS MUST BE CENTRED IN HOLES THE ACRYLIC PANEL EXPANDS AND CONTRACTS AT A DIFFERENT RATE THAN THE SKYLIGHT FRAME. IF THE SHANK OF THE SCREW IS TIGHT AGAINST THE ACRYLIC PANEL, CRACKING WILL OCCUR. TAKE THE NECESSARY TIME TO PROPERLY CENTRE EACH SCREW. 90 J 1 1/2" #10 METAL ROOF SCREW (1/4" HEAD) WITH POLYZIP WASHER 14 req

30 Step Twenty PLACE THE SKYLIGHT ASSEMBLY INTO POSITION ON TOP OF THE SKYLIGHT FRAME. FASTEN THE SKYLIGHT ASSEMBLY TO THE SKYLIGHT FRAME FROM THE INSIDE. USE THREE SCREWS ON-ANGLE PER SIDE. SECTION VIEW A 1 1/2" ROBERTSON SCREWS 12 req

31 Step Twenty-one LAY ROOFING SHEETS (DC 1835, 1854, 1855, 1856) ON THE LAST SIDE OF THE ROOF. MIDDLE SHEETS ARE TO BE TIGHT TO THE OUTSIDE EDGE OF THE SKYLIGHT FRAME AND BENEATH THE SKYLIGHT FLASHING. THE OVERHANG IS TO BE EQUAL OVER THE ENTIRE EAVE. FASTEN THROUGH PRE-PUNCHED HOLES ONLY. DC-1853 IMPORTANT: FASTEN ALL SCREWS PRIOR TO STEPPING ON ROOF. DC-1856 DC-1855 DC-1854 FRONT VIEW I SECTION VIEW 1" ROOF SCREWS 40 req

32 Step Twenty Two CAREFULLY PEEL THE BACKER AND PLACE THE SEALING TAPE (DC-2033) UNDER THE SKYLIGHT FRAME FLASHING AS SHOWN IN DETAIL 1 SEALING TAPE DC

33 Step Twenty Three CAREFULLY PEEL BACKER AND PLACE THE SEALING TAPE (DC ) OVER TOP OF THE JOINT BETWEEN THE ROOFING SHEETS. APPLY PRESSURE TO ADHERE THE TAPE TO THE CONTOUR OF THE ROOFING SHEETS ONCE ADHERED FULLY, TRIM AT EDGE OF THE ROOFING SHEET AS SHOWN IN DETAIL 1 REPEAT THIS ON ALL FOUR SIDES CENTRED ON JOINT. THE SEALING TAPE MUST BE CENTERED ON THE JOINT. DETAIL 1

34 Step Twenty Four PLACE THE METAL HIP CAPS ON EACH CORNER OF THE ROOF AS SHOWN. PLACE EACH CAP SO THAT THE TOP OF THE CAP FITS TIGHT INTO THE CORNER OF THE SKYLIGHT FRAME UNDER THE SKYLIGHT FLASHING. MAKE SURE THAT THE CAP IS SITTING CENTRED ON THE HIP, THEN ATTACH IT THROUGH THE ROOFING SHEET AND INTO THE STRAPPING. SCREWS MUST BE FASTENED THROUGH THE TOP RIBS OF THE ROOFING SHEET ONLY. DO NOT OVER TIGHTEN, OR THE HIP CAPS MAY BE DAMAGED. SCREWS MUST BE FASTENED THROUGH THE TOP RIBS OF THE ROOFING SHEET ONLY. DC-1179 DC-1179 DC-1179 DC-1179 DC " ROOF SCREWS 24 req I

35 OPTIONAL BAY KIT IF YOU HAVE PURCHASED AN OPTIONAL BAY WALL KIT FOR YOUR OUTDOOR STRUCTURE, PLEASE MOVE ON TO STEP SEVEN OF THE INSTRUCTIONS PROVIDED WITH THE BAY KIT AT THIS TIME.

36 Step Twenty-three ASSEMBLE AND ATTACH THE DOOR HANDLE AND LATCH (DC 2008) TO THE DOOR. USE THE HARDWARE PACK PROVIDED. INSERT THE THUMB-BUTTON INTO THE HANDLE. INSERT THE FLAT METAL BAR INTO THE THUMB BUTTON. SLIDE THE SPRING OVER THE FLAT METAL BAR. PRESS THIS ASSEMBLY AGAINST THE DOOR AT THE THREE HOLES FIT THE LATCH TO THE OPPOSITE SIDE OF THE DOOR. USING A SCREWDRIVER, TIGHTEN THE ASSEMBLY TO THE DOOR. ATTACH THE BOTTOM OF THE HANDLE USING A SMALL SCREW. DISCARD ALL REMAINING HARDWARE FROM THE PACK. 0097_Jasper_11x11_Instructions_V1.2 EN

37 Step Twenty Six INSTALL SCREEN FRAMES (DC 1747) INTO THE WALL PANELS. TURN CLIPS TO LOCK THE SCREEN FRAME IN PLACE. 0097_Jasper_11x11_Instructions_V1.2 EN

38