Hardware, Track, Sill System & Weathersealing for Exterior Folding Doors & Windows

Transcription

1 Exterior Folding Door Systems E3 SYSTEM Hardware, Track, Sill System & Weathersealing for Exterior Folding Doors & Windows E3 Specification & Fabrication Catalogue Revision (17) March 15, 2018 PRINTED CATALOGUE MAY NOT BE UP TO DATE, ALWAYS REFER TO PRODUCT WEBSITE FOR MOST UP TO DATE CONTENT.

2 E3 HARDWARE, TRACK, SILL SYSTEM & WEATHERSEALING FOR FOLDING DOORS & WINDOWS In a single direction maximum panel weight: 250lbs (115kg) each panel maximum panel width: 47-1/4 (1200mm) maximum panel height: /64 (3600mm) maximum number of panels: 8 each way panel thickness: 1-3/4 (44.5mm) or 2-1/4 (57mm) when using E3 sill system panel thickness: 1-3/8 (34.9mm) to 3 (76.2mm) when using floor channel NOTE: When using maximum panel width & height 47-1/4 (1200mm) x /64 (3600mm) panel may exceed maximum panel weight of 250 lbs (115 kg). Calculated weight check should be done. KTE3DJ Eclipse E3 Drilling Jig See E3 Drilling Jig instruction sheet on (under Products > E3 folding door systems) Parts Selection Eclipse E3 is specified with 5 separate groups: track, sill, weathersealing, flushbolts and hardware. Components are required from all 5 groups to build an Eclipse folding door system. Top Track With flushbolt pin channel 3-37/64 (90.9mm) KT75C clear anodized KT75D bronze anodized Lengths available: 111, 147, 183, 222, 294 (2.81m, 3.73m, 4.64m, 5.63m, 7.46m) Top Track, extruded aluminum (OPTIONAL) 2-7/16 (62mm) 2 (50.2mm) 1-31/32 (50mm) NEW PRODUCT KT70D bronze anodized. Lengths available: 111, 147, 183, 222, 294 (2819mm, 3754mm, 4648mm, 5639mm, 7468mm) Sill System KT768GASKET sill to jamb assembly gasket NEW PRODUCT Fir top water return sill, extruded aluminum clear or bronze anodized. KT795 8 wide (203mm) for 1-3/4 (44.5mm) door. KT797 8 wide (203mm) for 2-1/4 (57mm) door. KT /16 wide (167mm) for 1-3/4 (44.5mm) door. KT /16 wide (167mm) for 2-1/4 (57mm) door. Lengths available: 111, 147, 183, 222, 294 (2819mm, 3754mm, 4648mm, 5639mm, 7468mm). Order flushbolt cups and sill assembly end gaskets separately. KT795COVERBLVE PVC insert, black. Snap in cover for flushbolt channels for the new Eclipse sill & top track. Fits into sills above. Floor Channel KT23DV floor channel, bronze anodized with PVC insert, black. Lengths available: 111, 147, 183, 222, 294 (2.81m, 3.73m, 4.64m, 5.63m, 7.46m) KT750GASKET included with KT749, fits under rim of cup KT23BLVE Replacement PVC insert (only) KT749 Flushbolt cup, satin or bronze Flushbolt cup used with floor channel and ADA sill Weatherseals & Astragal DS434 Weatherseal for sill, jamb and header. Black, brown or white KT190 Fir astragal, may be stained or painted Flushbolts or Twinpoint FOR OUTSWING & INSWING DOORS 4 lengths available: NEW PRODUCT Hardware 2 stock finishes available: Stainless steel & pvd bronze DS416 Weatherseal for between doors. Black, brown or white DS369A7145BL Aluminum T-slot extrusion with black pile insert, for bottom of doors DS415BL black DS415W white DS415B brown weatherseal for between doors, use on clad doors where kerf slot is not possible 2 ALL DRAWINGS NO SCALE DS434 Kerf seal DSP108-35BL Pile weatherseal for door with astragal, 5/16 (8mm) pile height, black DS BL Pile weatherseal for KT70 & KT75 top track, black 7-7/8 (200mm) 15-3/4 (400mm) 23-5/8 (600mm) 39-3/8 (1000mm) 1" (25.4mm) DBOT & DBSY Style 1 (25.4mm) throw length regardless of bolt length. Finishes available: brushed aluminum or bronze powder coat. PVD brass (TG) finish is custom order, call for manufacturing time. Copyright 2018 Eclipse Architectural

3 INDEX KT190C84B 2, 33 KT190C84BL 2, 33 KT190C84W 2, 33 KT190C96B 2, 33 KT190C96BL 2, 33 KT190C96W 2, 33 KT190C108B 2, 33 KT190C108BL 2, 33 KT190C108W 2, 33 KT190C120B 2, 33 KT190C120BL 2, 33 KT190C120W 2, 33 KT23BLVE 2, 32 KT23DV 2, 32 KT23D-RADIUS 19, 32 DS369A7145BL 2, 8, 9, 10, 11 DS416B 2, 5, 9, 12 DS416BL 2, 5, 9, 12 DS416W 2, 5, 9, 12 DS434B 2, 15, 16 DS434B81 2, 15, 16 DS434B96 2, 15, 16 DS434BL 2, 15, 16 DS434BL81 2, 15, 16 DS434BL96 2, 15, 16 DS434W 2, 15, 16 DS434W81 2, 15, 16 DS434W96 2, 15, 16 DS415B96 2 DS415B144 2 DS415W96 2 DS415W144 2 DS415BL144 2 KT769D 21 KT779D 20 KT70D 17 KT70D-RADIUS 17 KT75C 2, 14, 15, 16 KT75D 2, 14, 15, 16 KT749BRONZE 2, 23, 24 KT749DCH 2, 23, 24 KT750SPC 2, 8, 10 KT760SPC 10, 11, 16 KT770SPC 9, 11 KT780SPC 8, 9 KT752E3FIRD 16 KT788E3D 16 KT841REDUCER 9, 11 KTDBSY 24 KTDBOC200NRTG 22 KTDBOC200NRQ 22 KTDBOC200NRX 22 KTDBOC400NRTG 22 KTDBOC400NRQ 22 KTDBOC400NRX 22 KTDBOE200NRTG 22 KTDBOE200NRQ 22 KTDBOE200NRX 22 KTDBOE400NRTG 22 KTDBOE400NRQ 22 KTDBOE400NRX 22 KTDBOE600NRTG 22 KTDBOE600NRQ 22 KTDBOE600NRX 22 KTDBOE1000NRTG 22 KTDBOE1000NRQ 22 KTDBOE1000NRX 22 KTDBOT200NRTG 23 KTDBOT200NRQ 23 KTDBOT200NRX 23 KTDBOT400NRTG 23 KTDBOT400NRQ 23 KTDBOT400NRX 23 KTDBOT600NRTG 23 KTDBOT600NRQ 23 KTDBOT600NRX 23 KTDBOT1000NRTG 23 KTDBOT1000NRQ 23 KTDBOT1000NRX 23 KTE3CTG 36, 37 KTE3COL 36, 37 KTE3CS 36, 37 KTE3CLCSTG 36, 37 KTE3CLCSOL 36, 37 KTE3CLCSS 36, 37 KTE3CTG 36, 37 KTE3COL 36, 37 KTE3CS 36, 37 KTE3CRCSTG 36, 37 KTE3CRCSOL 36, 37 KTE3CRCSS 36, 37 KTE3EHTG 36, 37 KTE3EHOL 36, 37 KTE3E 36, 37 KTE3HTG 36, 37 KTE3HOL 36, 37 KTE3 36, 37 KTE3HHTG 36, 37 KTE3HHOL 36, 37 KTE3 36, 37 KTE3HHNHTG 36, 37 KTE3HHNHOL 36, 37 KTE3HHN 36, 37 KTE3HNHTG 36, 37 KTE3HNHOL 36, 37 KTE3HN 36, 37 KTE3HHNTG 36, 37 KTE3HHNOL 36, 37 KTE3HHNS 36, 37 KTE3HHTG 36, 37 KTE3OL 36, 37 KTE3S 36, 37 KTE3HNTG 36, 37 KTE3HNOL 36, 37 KTE3HNS 36, 37 KTE3TG 36, 37 KTE3OL 36, 37 KTE3S 36, 37 KTE3TG 36, 37 KTE3OL 36, 37 KTE3S 36, 37 DSP108-35BL 2, 5, 12, 13 DS BL 14,20, 21, 22 Misc / Spare & Replacement Parts KT750GASKET 2 KT768GASKET 2, 32 KTDBPCS 22 KTDBSPQ 22, 23, 24 KTDBS 22, 23, 24 KTE2DBFORB 22, 23, 24 KTE3CBPIVOTH 36 KTE3DJ 2 KTE3HGASKET 4 KTE3SCREWTG 37 KTE3SCREWOL 37 KTE3SCREWSS 37 KTE3WPCUPQ 36 KTE3WPCU 36 KTEMAG 35 KTDBSPOCX or Q 22 KT740DHC 33 KT740DHD 33 KT745ESPX 5, 7 KT745ESPQ 5, 7 KTDCAS 34 KTDCAOL 34 Twinpoint ECLT2TRSN , 28,29,30 ECLT2TRSN , 28,29,30 ECLT2NS 27 ECDF3SHN 27 ECDF4SHNS 27 ECLTBC8S 27, 30 ECLT2RB 27, 29 ECLTSP8SS 27, 30 ECLTSP8OL 27, 30 Legend X TG OL Q SS C D B BVE BL DHC DHD DHBL DHW BL Swing IS OS Satin aluminum PVD brass (custom order) PVD bronze Powder coat bronze Stainless steel Clear anodized Bronze anodized Brown Black vinyl extrusion Black Satin / clear Bronze anodized Black powder coat White powder coat Black pile Inswing Outswing Misc SPC Sill protective cover GASKET A/B gasket FORB Router bit FIR Fir top mould DJ Drill jig for hinges Lengths For Flushbolts 7-7/8 (200mm) 15-3/4 (400mm) 23-5/8 (600mm) 39-3/8 (1000mm) Hardware Intermediate carrier 3 piece set LCS Left carrier 2 piece set RCS Right corner 2 piece set Pivot top & bottom 2 piece set EH D pull handle 1 piece H Hinge flat with handle 1 piece HH Hinge offset with handle 1 piece HNH Hinge flat no handle 1 piece HHNH Hinge offset no handle 1 piece Hinge flat with handle 3 piece set Hinge offset with handle 3 piece set HN Hinge flat no handle 3 piece set HHN Hinge offset no handle 3 piece set WP Wall pivot Misc / Spare Hardware Components PCS End cap for OC flushbolts pin SP Striker plate CBP Bottom pivot housing PCP Pivot cap SCREW Screws for hinge flaps SPOC Striker plate OC flushbolt TPPLATE Top pivot mounting plate DH Door hold Flushbolts KTDBOT For outswing application KTDBOC For inswing application installed at bottom of panels KTDBOE For inswing application installed at top of panels KTDBSY For outswing application Copyright 2018 Eclipse Architectural 3

4 E3 ARCHITECTURAL DETAIL panel width 4 one way configuration half offset hinges 5-1/2 (139.7mm) panel thickness 1-5/16 (33.5mm) 5/8 (16mm) panel offset 19/32 (15mm) 19/32 (15mm) hinge offset outswing panels 2-7/16 (62mm) KT70 top track KT75 top track 3/16 (5mm) panel clearance to head top of door to top of hinge flap 19/32 (15mm) 2 (50.2mm) 2-3/8 (60mm) top of door to top of hinge flap when using flush bolts. 5-29/32 (150mm) when using twinpoint lock. Centre of top track to centre of bottom channel 23/32 (18.5mm) R.O. 1-17/32 (39mm) to face of door 5/16 (8mm) from center of top track to face of door centre of track to centre of channel 23/32 (18.5mm) KTE3HGASKET Adhesive black gasket for optimum sealing performance around all hinge flaps. neoprene black gasket KT795 sill 19/32 (15mm) 3/8 (9.5mm) panel clearance to sill 7/8 (22mm) 2-3/8 (60mm) bottom of door to bottom of hinge flap when using flush bolts. 5-29/32 (150mm) when using twinpoint lock. 15/16 (24mm) 4 ALL DRAWINGS NO SCALE Copyright 2018 Eclipse Architectural

5 E3 ARCHITECTURAL DETAIL Outswing Application NOTE: when using 2-1/4 (57mm) panel thickness on 2L2R and 4L4R configurations, the gapping between the 2 meeting panels should be 1/2 (12.7mm). Hinge flaps on the meeting stiles should be machined into the edge of the door. 9/32 (7mm) jamb clearance 5/32 (4mm) panel to panel gap 9/32 (7mm) jamb clearance 11/16 (17.5mm) jamb thickness 5/32 (4mm) panel to panel gap 5/32 (4mm) panel to panel gap 4L (4 doors folding left) Exterior View (all doors are same width) 9/32 (7mm) jamb clearance top pivot wall pivot hinge set facing inside intermediate carrier set right hand carrier hinge set facing inside 9/32 (7mm) jamb clearance bottom pivot bottom guide jamb or pivot door basic door basic door leading door DS416 & DSP108-35BL Weatherseal Detail for 1-3/4 (44.5mm) Door 11/16 (17.5mm) 11/16 (17.5mm) 39/64 (15.4mm) Extended Jamb Strike Used only with MultiPoint lock set 6-9/16 (166.7mm) pivot door weatherseal application 4-3/8 (110.6mm) 3/8 (9.5mm) CL CL 1/8 (3.2mm) 9/32 (7mm) 1/8 (3.5mm) DS434 5/16 (7.4mm) 1-5/8 (41mm) 1-3/4 (44.5mm) REF REF 3/8 (9.5mm) CL 9/16 (14mm) 1-7/16 (36mm) RH DSSPLK732 60RH flushbolt machining centered at stile width RO.5 (R1/64) 1/8 (2.5mm) 9/16 (14mm) 5/16 (7.4mm) 3/4 (18.5mm) 5/16 (7.4mm) 1/8 (2.8mm) LH DSSPLK731 60LH 5/32 (4mm) 5/16 (7.4mm) latching door to jamb, weatherseal & strike plate application for 3L, 3R, 5L, 5R, 7L or 7R. DS416 DSP108 35BL KT745 extended strike plate for 1-3/4 (44.45mm) door thickness only. Used with standard style lock set. 4-5/16 (107mm) Extended Strike Plate for 1-3/4 Door Only. Used with standard style lock set. 4 (107mm) 4-5/16 (110mm) KT745ESPX Satin finish KT745ESPQ Bronze powder coat Copyright 2018 Eclipse Architectural 5 ALL DRAWINGS NO SCALE

6 HARDWARE LIST FOR DOOR CONFIGURATIONS Passage Set/Lock, Flushbolt, Astragal & Hardware Placement For Outswing Applications From Left To Right 2L 3L 4L 3L2R 5L 2L1R 3L1R 4L1R DH DH DH RCS RCS this configuration not accessible from exterior ESP RCS DH RCS LCS this configuration not accessible from exterior ESP 1x KTE3 middle wall pivot 1x KTE3C pivot set 1x KTE3CRCS right carrier set 1x KTE3 hinge set 2x KTDB non-keyed flushbolt 2x KTE3 middle wall pivot 2x KTE3C pivot set 1x KTE3CRCS right carrier set 1x KTE3 hinge set 2x KTDB non-keyed flushbolt 1x KTE3 middle wall pivot 1x KTE3C pivot set 1x KTE3C intermediate carrier set 1x KTE3 half offset hinge set 2x KTDB non-keyed flushbolt 2x KTE3 middle wall pivot 2x KTE3C pivot set 1x KTE3C intermediate carrier set 1x KTE3 half offset hinge set 4x KTDB non-keyed flushbolt 1x KTE3 middle wall pivot 1x KTE3C pivot set 1x KTE3C intermediate carrier set 1x KTE3CRCS right carrier set 2x KTE3 half offset hinge set 4x KTDB non-keyed flushbolt 2x KTE3 middle wall pivot 2x KTE3C pivot set 1x KTE3C intermediate carrier set 1x KTE3CRCS right carrier set 2x KTE3 half offset hinge set 4x KTDB non-keyed flushbolt 2x KTE3 middle wall pivot 2x KTE3C pivot set 1x KTE3C intermediate carrier set 1x KTE3CLCS left carrier set 1x KTE3 hinge set 1x KTE3 half offset hinge set 4x KTDB non-keyed flushbolt 1x KTE3 middle wall pivot 1x KTE3C pivot set 2x KTE3C intermediate carrier set 1x KTE3 hinge set 1x KTE3 half offset hinge set 4x KTDB non-keyed flushbolt Hardware Legend Pivot set Wall pivot set Intermediate carrier set LCS Left carrier set RCS Right carrier set Half offset hinge set Hinge set (flat) Flushbolt ESP Extended strike plate DH Door hold MAG Magnet TP Twinpoint Floating Door Pairs Per pair of doors: 1x KTE3CLCS left carrier set 1x KTE3CRCS right carrier set 1x KTE3 hinge set 2x KTDB non-keyed flushbolt LEGEND Passage Set Lock by Other Flushbolts Top & Bottom Twinpoint Option to Astragal Door Hold DH Extended strike plate for 1-3/4 door only 4 4-5/16 KT745ESPX Satin finish KT745ESPQ Bronze powder coat 3L3R 7L 4L3R 5L2R 5L3R 6L RCS LCS DH 2x KTE3 middle wall pivot 2x KTE3C pivot set 2x KTE3C intermediate carrier set 2x KTE3 half offset hinge set 6x KTDB non-keyed flushbolt DH DH 1x KTE3 middle wall pivot 1x KTE3C pivot set 3x KTE3C intermediate carrier set ESP 2x KTE3 hinge set 1x KTE3 half offset hinge set DH 6x KTDB non-keyed flushbolt DH may be reversed DH DH 2x KTE3 middle wall pivot 2x KTE3C pivot set 2x KTE3C intermediate carrier set 1x KTE3CRCS right carrier set 3x KTE3 half offset hinge set 6x KTDB non-keyed flushbolt 2x KTE3 middle wall pivot 2x KTE3C pivot set 2x KTE3C intermediate carrier set 1x KTE3CLCS left carrier set 2x KTE3 hinge set 1x KTE3 half offset hinge set 6x KTDB non-keyed flushbolt 2x KTE3 middle wall pivot 2x KTE3C pivot set 3x KTE3C intermediate carrier set 1x KTE3 hinge set 2x KTE3 half offset hinge set 8x KTDB non-keyed flushbolt 1x KTE3 middle wall pivot RCS 1x KTE3C pivot set 2x KTE3C intermediate carrier set this configuration 1x KTE3CRCS right carrier set not accessible 1x KTE3 hinge set from exterior 2x KTE3 half offset hinge set 6x KTDB non-keyed flushbolt How To Determine Swing Of Systems Configuration is always determined when viewing system from exterior side, going from left to right. 3L 3L OUTSWING 3LI INSWING outswing application D pull handle option Use one D pull handle on each pair of inswing doors to pull open and close doors. Inswing application D pull handle option 5RI Use D pull handle on exit door (outswing system) where passage set / lock not required. Use flushbolts top and bottom to lock door from the inside only. NOTE: exit door not accessible from exterior. 6 ALL DRAWINGS NO SCALE Copyright 2018 Eclipse Architectural

7 HARDWARE LIST FOR DOOR CONFIGURATIONS Passage Set/Lock, Flushbolt, Astragal & Hardware Placement For Outswing Applications From Left To Right 2R LCS 1L2R 3R 1L3R ESP 2L2R 1L4R 2L3R ESP 8R LCS This configuration not accessible from exterior LCS LCS 4R This configuration not accessible from exterior 5R 3L4R 7R DH may be reversed 2L5R RCS LCS RCS DH RCS This configuration not accessible from exterior DH DH LCS DH Hardware Application 3L2R DH LCS DH This configuration not accessible from exterior pivot set intermediate carrier & guide set basic door jamb door service door flushbolts door hold passage set half offset hinge set 1x KTE3 middle wall pivot 1x KTE3C pivot set 1x KTE3CLCS left carrier set 1x KTE3 hinge set 2x KTDB non-keyed flushbolt 2x KTE3 middle wall pivot 2x KTE3C pivot set 1x KTE3CLCS left carrier set 1x KTE3 hinge set 2x KTDB non-keyed flushbolt 1x KTE3 middle wall pivot 1x KTE3C pivot set 1x KTE3C intermediate carrier set 1x KTE3 half offset hinge set 2x KTDB non-keyed flushbolt 2x KTE3 middle wall pivot 2x KTE3C pivot set 1x KTE3C intermediate carrier set 1x KTE3 half offset hinge set 4x KTDB non-keyed flushbolt 2x KTE3 middle wall pivot 2x KTE3C pivot set 1x KTE3CLCS left carrier set 1x KTE3CRCS right carrier set 2x KTE3 hinge set 4x KTDB non-keyed flushbolt 2x KTE3 middle wall pivot 2x KTE3C pivot set 1x KTE3C intermediate carrier set 1x KTE3CLCS left carrier set 2x KTE3 half offset hinge set 4x KTDB non-keyed flushbolt 1x KTE3 middle wall pivot 1x KTE3C pivot set 1x KTE3C intermediate carrier set 1x KTE3CLCS left carrier set 2x KTE3 half offset hinge set 4x KTDB non-keyed flushbolt 2x KTE3 middle wall pivot 2x KTE3C pivot set 1x KTE3C intermediate carrier set 1x KTE3CRCS right carrier set 1x KTE3 hinge set 1x KTE3 half offset hinge set 4x KTDB non-keyed flushbolt 1x KTE3 middle wall pivot 1x KTE3C pivot set 2x KTE3C intermediate carrier set 1x KTE3 hinge set 1x KTE3 half offset hinge set 4x KTDB non-keyed flushbolt 2x KTE3 middle wall pivot 2x KTE3C pivot set 2x KTE3C intermediate carrier set 1x KTE3CLCS left carrier set 3x KTE3 half offset hinge set 6x KTDB non-keyed flushbolt 1x KTE3 middle wall pivot 1x KTE3C pivot set 3x KTE3C intermediate carrier set 2x KTE3 hinge set 1x KTE3 half offset hinge set 6x KTDB non-keyed flushbolt 2x KTE3 middle wall pivot 2x KTE3C pivot set 2x KTE3C intermediate carrier set 1x KTE3CRCS right carrier set 2x KTE3 hinge set 1x KTE3 half offset hinge set 6x KTDB non-keyed flushbolt left carrier & guide set leading door 1x KTE3 middle wall pivot 1x KTE3C pivot set 3x KTE3C intermediate carrier set 1x KTE3CLCS left carrier set 2x KTE3 hinge set 2x KTE3 half offset hinge set 8x KTDB non-keyed flushbolt flat hinge set pivot set jamb door flushbolts Hardware Legend Pivot set Wall pivot set Intermediate carrier set LCS Left carrier set RCS Right carrier set Half offset hinge set Hinge set (flat) Flushbolt ESP Extended strike plate DH Door hold MAG Magnet TP Twinpoint panel offset 19/32 (15mm) RH DSSPLK732 60RH Legend Passage Set Lock by Other Flushbolts Top & Bottom Twinpoint Option to Astragal Door Hold DH Extended Strike Plate for 1-3/4 Door Only. Used with standard style lock set. 4-5/16 KT745ESPX Satin finish KT745ESPQ Bronze powder coat Extended Jamb Strike Used only with MultiPoint lock set panel width 4 4 one way configuration 19/32 (15mm) hinge offset LH DSSPLK731 60LH half offset hinges panel thickness 5/8 (16mm) outswing panels Copyright 2018 Eclipse Architectural 7 ALL DRAWINGS NO SCALE

8 ECLIE, KT797 (8") OUTSWING SILL SYSTEM FOR 2-1/4" (57MM) DOOR THICKNESS Extrusion Alloy 6063 T5. Actual Full Sill Width: 8" (203mm) Channel Sill for Flushbolt or Twinpoint. New Generation Sill with Flushbolt Pin Channel. Sill is fabricated as shown by Eclipse Architectural. KT797E3FIRC Clear anodized KT797E3FIRD Bronze anodized Two locking options: DBOT Flushbolt Twinpoint E3 bottom hinge & guide KT797 Sill 6-9/16 (166.7mm) jamb line 19/32 (15mm) 1-3/16 (30mm) vinyl channel insert weep hole weep holes 2-5/32 (54mm) 13/32 (10mm) 1/4 (6mm) KT780SPC Protective vinyl sill cover for sill nose 2-1/4 (57mm) centre of top track to centre of bottom channel = 23/32 (18.5mm) DS369A7145BL Aluminum T-slot extrusion with gray pile insert 3/8 (9.5mm) DS434 Kerf seal 6-9/16 (166.7mm) jamb line 1-23/32 (44mm) KT795COVERBLVE PVC insert, black FIR OR OAK TOP WOOD SUBSTRATE 8 (203mm) KT750SPC Protective vinyl sill cover for interior fir top 8 FULL SCALE EXCEPT AS NOTED Copyright 2018 Eclipse Architectural

9 ECLIE KT795 (8 ) OUTSWING SILL SYSTEM FOR 1-3/4 (44.5MM) DOOR THICKNESS Extrusion Alloy 6063 T5. Actual Full Sill Width: 8 (203mm) Channel Sill for Flushbolt or Twinpoint. New Generation Sill with Flushbolt Pin Channel. Sill is fabricated as shown by Eclipse Architectural. KT795E3FIRC Clear anodized KT795E3FIRD Bronze anodized 1-3/16 (30mm) Two locking options: DBOT Flushbolt Twinpoint E3 bottom hinge & guide KT795 Sill 13/32 (10mm) 6-9/16 (166.7mm) jamb line 19/32 (15mm) vinyl channel insert weep hole weep holes 2-5/32 (54mm) 1/4 (6mm) KT780SPC Protective vinyl sill cover for sill nose 1-3/4 (44.5mm) centre of top track to centre of bottom channel = 23/32 (18.5mm) DS369A7145BL Aluminum T-slot extrusion with gray pile insert 3/8 (9.5mm) DS434 Kerf seal 2-7/32 (57mm) 6-9/16 (166.7mm) jamb line KT795COVERBLVE PVC insert, black FIR OR OAK TOP KT841 Reducer WOOD SUBSTRATE 8 (203mm) KT770SPC Protective vinyl sill cover for interior fir top Copyright 2018 Eclipse Architectural FULL SCALE EXCEPT AS NOTED 9

10 ECLIE KT777 (6-9/16 ) OUTSWING SILL SYSTEM FOR 2-1/4 (57MM) DOOR THICKNESS Extrusion Alloy 6063 T5. Actual Full Sill Width: 6-9/16 (166.7mm) Channel Sill for Flushbolt or Twinpoint. New Generation Sill with Flushbolt Pin Channel. Sill is fabricated as shown by Eclipse Architectural. KT777E3FIRC KT777E3FIRD Clear anodized Bronze anodized Two locking options: DBOT Flushbolt Twinpoint E3 bottom hinge & guide 13/32 (10mm) 1/4 (6mm) 19/32 (15mm) 1-3/16 (30mm) vinyl channel insert weep hole 2-1/4 (57mm) 6-9/16 (166.7mm) jamb line 1-23/32 (44mm) weep holes 6-9/16 (167mm) 2-5/32 (54mm) 6-9/16 (166.7mm) jamb line KT777 Sill KT760SPC Protective vinyl sill cover for sill nose centre of top track to centre of bottom channel = 23/32 (18.5mm) DS369A7145BL Aluminum T-slot extrusion with gray pile insert 3/8 (9.5mm) DS434 Kerf seal KT795COVERBLVE PVC insert, black FIR OR OAK TOP WOOD SUBSTRATE KT750SPC Protective vinyl sill cover for interior fir top 10 FULL SCALE EXCEPT AS NOTED Copyright 2018 Eclipse Architectural

11 ECLIE KT775 (6-9/16 ) OUTSWING SILL SYSTEM FOR 1-3/4 (44.5MM) DOOR THICKNESS Extrusion Alloy 6063 T5. Actual Full Sill Width: 6-9/16 (166.7mm) Channel Sill for Flushbolt or Twinpoint. New Generation Sill with Flushbolt Pin Channel. Sill is fabricated as shown by Eclipse Architectural. KT775E3FIRC KT775E3FIRD Clear anodized Bronze anodized Two locking options: DBOT Flushbolt Twinpoint E3 bottom hinge & guide 19/32 (15mm) 13/32 (10mm) 1/4 (6mm) 1-3/16 (30mm) vinyl channel insert 6-9/16 (166.7mm) jamb line weep holes 6-9/16 (167mm) 2-5/32 (54mm) 6-9/16 (166.7mm) jamb line KT775 Sill weep hole KT760SPC Protective vinyl sill cover for sill nose 1-3/4 (44.5mm) centre of top track to centre of bottom channel = 23/32 (18.5mm) DS369A7145BL Aluminum T-slot extrusion with gray pile insert 3/8 (9.5mm) DS434 Kerf seal 2-7/32 (57mm) KT795COVERBLVE PVC insert, black KT841 Reducer FIR OR OAK TOP WOOD SUBSTRATE KT770SPC Protective vinyl sill cover for interior fir top Copyright 2018 Eclipse Architectural FULL SCALE EXCEPT AS NOTED 11

12 E3 JAMB FOR 2-1/4 (57MM) DOOR THICKNESS Exterior E3 Folding Door, Outswing Application Two locking options: DBOT Flushbolt Twinpoint Multipoint latch Actual machining for flushbolts (face plate) 1-27/64 x 7-7/8 (36mm x 200mm) 1-27/64 x 15-3/4 (36mm x 400mm) 1-27/64 x 23-5/8 (36mm x 600mm) 1-27/64 x 39-3/8 (36mm x 1000mm) 6-9/16 (167mm) 4-27/32 (123mm) 11/16 (17.5mm) notch required in jamb 1/8 (3mm) 11/16 (17.5mm) 1/8 (3mm) 9/32 (7mm) 9/16 (15mm) 1-3/32 (28mm) 3/8 (9.5mm) DS434 kerf seal insert NO SCALE Dropbolt machining centered at stile width with dedicated router bits. CL R = 1/64 (0.5mm) 7/64 (2.5mm) 9/16 (14mm) 1-7/16 (36mm) REF KTE2DBFORB Flushbolt router bit is available Flushbolt machining depth: 1) KTDBSY 9/16 (14mm) 2) KTDBOC 43/64 (17mm) 3) KTDBOE 43/64 (17mm) 4) KTDBOT 3/4 (19mm) DS416 kerf seal insert DS434 kerf seal insert Multipoint face plate 2-1/4 (57mm) 7/64 (2.8mm) 5/16 (8mm) 9/32 (7mm) 19/64 (7.5mm) 5/16 (8mm) 5/32 (4mm) DSP108 35BL pile weathersesal Extended Jamb Strike Used only with MultiPoint lock set RH DSSPLK732 60RH NO SCALE LH DSSPLK731 60LH 12 FULL SCALE EXCEPT AS NOTED Copyright 2018 Eclipse Architectural

13 E3 JAMB FOR 1-3/4 (44.5MM) DOOR THICKNESS Exterior E3 Folding Door, Outswing Application. Two locking options: DBOT Flushbolt Twinpoint Actual machining for flushbolts (face plate) 1-27/64 x 7-7/8 (36mm x 200mm) 1-27/64 x 15-3/4 (36mm x 400mm) 1-27/64 x 23-5/8 (36mm x 600mm) 1-27/64 x 39-3/8 (36mm x 1000mm) 6-9/16 (167mm) 4-3/8 (110.6mm) 11/16 (17.5mm) 1/8 (3mm) 11/16 (17.5mm) 9/16 (15mm) NO SCALE 1/8 (3mm) 1-5/8 (41mm) Dropbolt machining centered at stile width with dedicated router bits. 3/8 (9.5mm) CL R = 1/64 (0.5mm) DS434 kerf seal insert 7/64 (2.5mm) CL 9/16 (14mm) 1-7/16 (36mm) 23/32 (18.5mm) 9/32 (7mm) CL Extended Strike Plate 4 (107mm) 4-5/16 (110mm) REF Flushbolt machining depth: 1) KTDBSY 9/16 (14mm) 2) KTDBOC 43/64 (17mm) 3) KTDBOE 43/64 (17mm) 4) KTDBOT 3/4 (19mm) DS416 kerf seal insert 1-3/4 (44.5mm) 7/64 (2.8mm) 5/16 (8mm) 9/32 (7mm) 19/64 (7.5mm) 5/16 (8mm) notch required in jamb DS434 kerf seal insert 5/32 (4mm) DSP108 35BL pile weathersesal Multipoint latch KT745ESPX Satin finish for 1-3/4 door only. Used with standard style lock set. NO SCALE KT745ESPQ Bronze powder coat KTE2DBFORB Flushbolt router bit is available Multipoint face plate Extended Jamb Strike Used only with MultiPoint lock set NO SCALE RH DSSPLK732 60RH LH DSSPLK731 60LH Copyright 2018 Eclipse Architectural FULL SCALE EXCEPT AS NOTED 13

14 KT75 TOP TRACK FOR 2-1/4 (57MM) DOOR THICKNESS E3 HEADER Exterior E3 Folding Door, KT75 Outswing Application Only. Channel Top Track for Flushbolt or Twinpoint. New Generation Top Track with Flushbolt Pin Channel. KT75C KT75D Clear Bronze anodized 2-21/32 (68mm) 3/16 (5mm) 6-9/16 (166.7mm) jamb line 11/16 (17mm) 19/32 (15mm) E3 bottom hinge & guide Two locking options: DBOT Flushbolt Twinpoint 6-9/16 (167mm) 5-7/8 (150mm) DS BL Pile weatherseal, black KT795COVERBLVE PVC insert, black 11/32 (9mm) 1/8 (3mm) 11/16 (18mm) 1-31/32 (50mm) 3/16 (5mm) 11/16 (18mm) DS434 Kerf seal 19/32 (15mm) 1-1/8 (28mm) 3/8 (9.5mm) 19/32 (15mm) 6-9/16 (166.7mm) jamb line 14 FULL SCALE EXCEPT AS NOTED Copyright 2018 Eclipse Architectural

15 KT75 TOP TRACK FOR 1-3/4 (44.5MM) DOOR THICKNESS E3 HEADER Exterior E3 Folding Door, KT75 Outswing Application Only. Channel Top Track for Flushbolt or Twinpoint. New Generation Top Track with Flushbolt Pin Channel. KT75C Clear anodized KT75D Bronze anodized 2-21/32 (68mm) 3/16 (5mm) 6-9/16 (166.7mm) jamb line 6-9/16 (167mm) 5-7/8 (150mm) 1/8 (3mm) 3/8 (9.5mm) 11/32 (9mm) 1-5/8 (41mm) 1/8 (3mm) 11/16 (18mm) 1-31/32 (50mm) 3/16 (5mm) 11/16 (18mm) 11/16 (17mm) 19/32 (15mm) E3 bottom hinge & guide Two locking options: DBOT Flushbolt Twinpoint KT795COVERBLVE PVC insert, black DS BL Pile weatherseal, black DS434 Kerf seal 11/32 (9mm) 19/32 (15mm) 6-9/16 (166.7mm) jamb line Copyright 2018 Eclipse Architectural FULL SCALE EXCEPT AS NOTED 15

16 KT752 SERIES E3 5-1/2 (139.7MM) OUTSWING SILL SYSTEM ONLY FOR 1-3/4 (44.5mm) Door Thickness & 4-9/16 (115.8 mm) Wall Thickness BRONZE ANODIZED ONLY KT752E3FIRD Outswing sill with fir top, bronze anodized 1-3/16 (30mm) DS434 sill weatherseal white, brown or black interior fir top mould KT752 E3 aluminum sill, clear or bronze anodized bottom roller guide channel channel for flushbolt pin 2-1/8 (54mm) 1-1/16 (27mm) weep hole vinyl channel insert substrate weep holes 5-1/2 (140 mm) KT760SPC Protective vinyl sill cover for sill nose NO SCALE Use KTDBSY series flush bolt KT788 E3 ADA LOWRISE ALUMINUM SILL FOR INSWING & OUTSWING DOORS NOTE: Door height plus 4-1/4 : (107.9mm) = R.O. (from finished floor line to R.O. header) when using Eclipse frame specs. KT788E3D Bronze anodized only ADA Compliant Slopes of threshold may be ripped off to achieve flush sill application. NO SCALE 1-3/4 (44.45mm) finished floor line 23/32 (18.5mm) 15/16 (23.6mm) 19/32 (15mm) 1-3/4 (44.45mm) 23/32 (18.5mm) no flush bolt cup used NO SCALE 1/2 (12.7mm) 19/32 (15mm) drill round hole for pin 6-9/16 (166.7mm) 15/16 (23.6mm) KTDBSY Flush bolt 1/2 (12.7mm) finished floor line thermal break 6-9/16 (166.7mm) KT749 flush bolt cup used, custom drilling required in sill 16 FULL SCALE EXCEPT AS NOTED Copyright 2018 Eclipse Architectural

17 E3 CORNER UNIT APPLICATION outside corner panel of 4R, 6R & 8R configurations door stop Apply lock set and/or deadbolt to active door or use flushbolts top & bottom (shown). If using interior flushbolts access from exterior not possible. Mitre cut sill and head to suit length of opening DS416 seal VIEW outside corner panel of 1L, 3L, 5L & 7L configurations E3 sill KT190 astragal VIEW OUTSIDE CORNER 3L 4R RADIUS APPLICATION (KT70 TRACK ONLY) Arc Length (AL) DOORS R = Radius (length from the C.P. to the edge of the circle) C = chord length X = height of crown CP = center point AL = arc length C CP X R Minimum Radius 14-7 / 175 (4445mm) to inside face of top track. (Warranty on hardware void if under minimum radius) Center point KT70D-RADIUS bronze anodized top track (CUSTOM ORDER)* KT23C-RADIUS clear anodized floor channel (CUSTOM ORDER)* KT23D-RADIUS bronze anodized floor channel (CUSTOM ORDER)* *CUSTOM ORDER, CALL FOR MANUFACTURING TIME. All supplied as one length only 120 (3048mm) DOORS Copyright 2018 Eclipse Architectural 17 ALL DRAWINGS NO SCALE

18 KT779D E3 SILL SYSTEM FOR 2-1/4 (57MM) DOOR THICKNESS Water Return All Aluminum Sill System, Thermally Broken For Inswing Folding Doors (Only KT70 Top Track can only be used on inswing application) BRONZE ANODIZED ONLY 6-9/16 (166.7mm) 11/16 (17.5mm) 2-7/16 (62mm) 11/16 (17.5mm) 3/8 (9mm) 2-11/16 (67.7mm) 2 (50.2mm) 1/4 (6mm) 3/8 (9.5mm) striker plate flushbolt pin Use KTDBOE Series flush bolt KT70 E3 aluminum top track 11/16 (17.5mm) 1/8 (3.17mm) 1-1/8 (28mm) 3/8 (9.5mm) DS434 kerf seal insert DS BL Pile weatherseal, black 5/16 (8mm) 1-29/32 (48.4mm) 3/16 (5mm) 4-7/8 (123.2mm) 2-1/16 (53.1mm) 3-15/16 (99.8mm) 2-1/4 (57mm) 7/16 (10.5mm) 1-11/16 (43.5mm) 3/8" (9.5mm) 11/16" (18mm) 7/16" (10.8mm) CL CL 23/32 (18.5mm) center line of top track to center line of bottom sill channel 10 slope 3/16 (4mm) KTDBSPOC Protective strike plate 2-1/8" (54mm) KT779D Sill bronze anodized only DS434 kerf seal insert WEEP HOLE DS369 1/4 (7mm) 1 (25.7mm) WEEP HOLE WEEP HOLE WEEP HOLE PVC channel filler I-Strut Thermal break 6-9/16 (166.7mm) Use KTDBOC Series flush bolt 18 FULL SCALE EXCEPT AS NOTED Copyright 2018 Eclipse Architectural

19 KT769D E3 SILL SYSTEM FOR 1-3/4 (44.5MM) DOOR THICKNESS Water Return All Aluminum Sill System, Thermally Broken For Inswing Folding Doors (Only KT70 Top Track can only be used on inswing application) BRONZE ANODIZED ONLY 6-9/16 (166.7mm) 11/16 (17.5mm) 2-7/16 (62mm) 11/16 (17.5mm) 3/8 (9mm) 2-11/16 (67.7mm) flushbolt pin center line CL of top track 2 (50.2mm) 1/4 (6mm) 3/8 (9.5mm) striker plate Use KTDBOE Series flush bolt KT70 E3 aluminum top track 11/16 (17.5mm) 1/8 (3.17mm) 1-5/8 (40.7mm) 3/8 (9.5mm) DS434 kerf seal insert DS BL pile weatherseal, black 5/16 (8mm) 1-29/32 (48.4mm) 3/16 (5mm) 4-3/8 (110.6mm) 3-15/16 (99.8mm) 2-9/16 (65mm) 1-3/4 (44.5mm) 7/16 (10.5mm) 2-3/8 (56.2mm) 3/8" (9.5mm) DS434 kerf seal insert 9/16" (14.3mm) 7/16" (10.8mm) CL CL 23/32 (18.5mm) center line of top track to center line of bottom sill channel 2-1/8" (54mm) 10 slope KT769D Sill Bronze anodized only WEEP HOLE DS369 3/16 (4mm) KTDBSPOC Protective strike plate 1/4 (7mm) 1 (25.7mm) WEEP HOLE WEEP HOLE WEEP HOLE PVC channel filler I-Strut Thermal break 6-9/16 (166.7mm) Use KTDBOC Series flush bolt Copyright 2018 Eclipse Architectural FULL SCALE EXCEPT AS NOTED 19

20 FLUSHBOLTS FOR E3 INSWING FOLDING DOORS: DBOE & DBOC SERIES 1-5/16 (33.3mm) face of door to center of pin 1" (25mm) KT70 Top track further machining required for inswing flush bolts offset pins 4 lengths available: 7-7/8 (200mm) 15-3/4 (400mm) 23-5/8 (600mm) 39-3/8 (1000mm) SPECIFICATIONS Minimum door thickness: 1-3/4 (44.5mm) DBOC Throw length: 3/4 (20mm) DBOE Throw length: 1 (25mm) Finishes: Bronze powder coat on aluminum to match pvd bronze finish on E3 hinges. Brushed metallic on aluminum to match stainless steel finish on E3 hinges. Bright gold (TG) finish on aluminum to match pvd brass finish on E3 hinges. Bright gold (TG) finish is custom order, call for manufacturing time. STRIKER FOR INSWING DOORS KTDBOE Top flushbolt 1-3/4 (45mm) min thickness KTDBOC Bottom flushbolt further machining required for larger bottom pin Flushbolt pin drops into bottom channel or into E3 inswing sill channel. 3/4" (20mm) E3 floor channel KTE2DBFORB Router bit for flushbolts fit striker to pin side of drop bolt (opposite the black plastic cap) KTDBPCS Replacement end cap for OC flushbolt pin fit centrally to the drop bolt when in the closed position Replacement strike plate for OC flushbolt KTDBSPOCX Brushed finish KTDBSPOCQ Bronze powder coat Actual machining for flushbolts (face plate) 1-27/64 x 7-7/8 (36mm x 200mm) 1-27/64 x 15-3/4 (36mm x 400mm) 1-27/64 x 23-5/8 (36mm x 600mm) 1-27/64 x 39-3/8 (36mm x 1000mm) OC flushbolt for bottom of doors Strike plate for header KTDBSPQ bronze powder coat KTDBS Satin chrome Router bit for flushbolts KTE2DBFORB OE flushbolt for top of doors PRODUCT CODE bronze powder coat finish over aluminum brushed metallic finish over aluminum to match stainless steel bright gold finish over aluminum DESCRIPTION KTDBOC200NRQ 8" (200mm) concealed 3/4, throw KTDBOE200NRQ 8" (200mm) 1 throw, round end KTDBOE400NRQ 16" (400mm) 1 throw, round end KTDBOE600NRQ 24" (600mm) 1 throw, round end KTDBOE1000NRQ 39" (1000mm) 1 throw, round end KTDBOC200NRX 8" (200mm) concealed, 3/4 throw KTDBOE200NRX 8" (200mm) 1 throw, round end KTDBOE400NRX 16" (400mm) 1 throw, round end KTDBOE600NRX 24" (600mm) 1 throw, round end KTDBOE1000NRX 39" (1000mm) 1 throw, round end KTDBOC200NRTG 8" (200mm) concealed, 3/4 throw KTDBOE200NRTG 8" (200mm) 1 throw, round end KTDBOE400NRTG 16" (400mm) 1 throw, round end KTDBOE600NRTG 24" (600mm) 1 throw, round end KTDBOE1000NRTG 39" (1000mm) 1 throw, round end Bright gold (TG) finish is custom order, call for manufacturing time. PLEASE NOTE: Flushbolt housing & slide bar are manufactured from aluminum components 20 ALL DRAWINGS NO SCALE Copyright 2018 Eclipse Architectural

21 FLUSHBOLTS FOR E3 OUTSWING FOLDING DOORS: DBOT SERIES SPECIFICATIONS Max wind load: 450kg (990lb) force Min door thickness: 1-3/4 (44.5mm) Throw length: 1 (25mm) Finishes: Bronze powder coat on aluminum to match pvd bronze finish on E3 hinges. Brushed metallic on aluminum to match stainless steel finish on E3 hinges. Bright gold (TG) finish on aluminum to match pvd brass finish on E3 hinges. Bright gold (TG) finish is custom order, call for manufacturing time. The flush-mounted flushbolts, rounded style and 1 (25mm) throw are designed for use with sliding and folding doors. This flushbolt will resist high winds and is rated to resist a 250kg load in Western Red Cedar and 450kg in Amoora. The bolts are easily installed with a dedicated router bit and are available in three finishes. Architectural Detail Flushbolt Assembly 1-27/64 (36mm) 43/64 (17mm) 35/64 (14mm) 47/64 (18.6mm) pin diameter 25/64 (10mm) 7-7/8 (200mm) 15-3/4 (400mm) 23-5/8 (600mm) 39-3/8 (1000mm) 1 (25mm) 1 (25mm) throw length regardless of bolt length 2-7/16 (62mm) 7/8 (22mm) 13/16 (20.6mm) KT749 Flushbolt cup used with floor channel and ADA sill 1/8 (2.5mm) 1-27/64 (36mm) CL 9/16 (14mm) flushbolt machining centered at stile width 3/4 (19mm) R = 1/64 (0.5mm) Actual machining for flushbolts (face plate) 1-27/64 x 7-7/8 (36mm x 200mm) 1-27/64 x 23-5/8 (36mm x 600mm) 1-27/64 x 15-3/4 (36mm x 400mm) 1-27/64 x 39-3/8 (36mm x 1000mm) SELECT FINISH PRODUCT NUMBER DESCRIPTION bronze powder coat finish on aluminum brushed metallic finish on aluminum to match stainless steel bright gold finish on aluminum KTDBOT200NRQ 8" (200mm) 1 throw, round end KTDBOT400NRQ 16" (400mm) 1 throw, round end KTDBOT600NRQ 24" (600mm) 1 throw, round end KTDBOT1000NRQ 39" (1000mm) 1 throw, round end KTDBOT200NRX 8" (200mm) 1 throw, round end KTDBOT400NRX 16" (400mm) 1 throw, round end KTDBOT600NRX 24" (600mm) 1 throw, round end KTDBOT1000NRX 39" (1000mm) 1 throw, round end KTDBOT200NRTG 8" (200mm) 1 throw, round end KTDBOT400NRTG 16" (400mm) 1 throw, round end KTDBOT600NRTG 24" (600mm) 1 throw, round end Bright gold (TG) finish is custom order, call for manufacturing time. Flushbolt cup used with floor channel and ADA sill KT749BRONZE bronze powder coat KT749DCH Satin chrome KTE2DBFORB Router bit for flushbolts (dedicated router bits are available) Strike plate for header KTDBSPQ bronze powder coat KTDBS Satin chrome PLEASE NOTE: Flushbolt housing & slide bar are manufactured from aluminum components Copyright 2018 Eclipse Architectural 21 ALL DRAWINGS NO SCALE

22 FLUSHBOLTS FOR OUTSWING FOLDING DOORS: DBSY SERIES Used with KT788 ADA Sill and KT23 Floor Channel SPECIFICATIONS Max wind load: 450kg (990lb) force Min door thickness: 1-3/4 (44.5mm) Bolt lengths: 8, 16, 24, 39 (200mm, 400mm, 600mm, 1000mm) Finishes: Bright gold to match pvd brass hardware bronze powder coat on aluminum to match the pvd bronze hardware & brushed metallic to match stainless steel hardware Symphony The flush-mounted flushbolts, rounded style and 1 (25mm) throw are designed for use with sliding and folding doors. Symphony will resist high winds and is rated to resist a 250kg load in Western Red Cedar and 450kg in Amoora. The bolts are easily installed with a dedicated router bit and are available in three finishes. Architectural Detail Flushbolt Assembly (Machining Spec) 17/32 (13mm) 1-27/64 (36mm) 7-7/8 (200mm) 15-3/4 (400mm) 23-5/8 (600mm) 39-3/8 (1000mm) 1-31/32 (50mm) pin diameter 9/16 (14mm) 1 (25mm) 7/8 (22mm) 2-7/16 (62mm) 13/16 (20.6mm) KT749 Flushbolt cup used with floor channel and ADA sill 1/8 (2.5mm) 1-27/64 (36mm) CL 9/16 (14mm) flushbolt machining centered at stile width 3/4 (19mm) R = 1/64 (0.5mm) Actual machining for flushbolts (face plate) 1-27/64 x 7-7/8 (36mm x 200mm) 1-27/64 x 23-5/8 (36mm x 600mm) 1-27/64 x 15-3/4 (36mm x 400mm) 1-27/64 x 39-3/8 (36mm x 1000mm) Flushbolt cup used with floor channel and ADA sill KT749BRONZE bronze powder coat KT749DCH Satin chrome KTE2DBFORB Router bit for flushbolts (dedicated router bits are available) Strike plate for header KTDBSPQ bronze powder coat KTDBS Satin chrome PLEASE NOTE: Flushbolt housing & slide bar are manufactured from aluminum components 22 ALL DRAWINGS NO SCALE SELECT FINISH PRODUCT NUMBER DESCRIPTION bright gold finish over aluminum powder coat finish bronze over aluminum brushed metallic finish over aluminum to match stainless steel KTDBSY200NRTG 8 (200mm), 1 throw, round end KTDBSY400NRTG 16 (400mm) 1 throw, round end KTDBSY600NRTG 24 (600mm) 1 throw, round end KTDBSY200NRQ 8 (200mm) 1 throw, round end KTDBSY400NRQ 16 (400mm) 1 throw, round end KTDBSY600NRQ 24 (600mm) 1 throw, round end KTDBSY1000NRQ 39 (1000mm) 1 throw, round end KTDBSY200NRX 8 (200mm) 1 throw, round end KTDBSY400NRX 16 (400mm) 1 throw, round end KTDBSY600NRX 24 (600mm) 1 throw, round end KTDBSY1000NRX 39 (1000mm) 1 throw, round end Bright gold ( TG) finish is custom order, call for manufacturing time. Copyright 2018 Eclipse Architectural

23 ECLIE E3 DRILLING JIG INSTRUCTIONS 3.57mm (9/64 ) Drilling for 15mm (19/32 ) Pivot / Intermediate / LH & RH Carrier Sets Align the stiles from ajoining doors next to each other on the bench or similar. Push the 15mm (19/32 ) buttons at the first end, then align them hard up to the bottom of the buttons while holding the stiles tight up to each other, then drill holes to depth of screw. Push all buttons up so the jig can slide to the center where a mark should be added to the stiles. Align the V in the side of the jig with the mark on the stile, then drill holes to the depth of screw. Push all buttons up and slide the jig down the opposite end. Push the 15mm (19/32 ) buttons at the other end, then align them hard up to the bottom of the buttons while holding the stiles tight to each other, then drill holes to depth of screw. KTE3DJ SPECIAL ORDER ONLY Drill all holes using a 3.57mm (9/64 ) drill for use with the 10 gauge screws supplied in all Centor sets. Alternatively you can drill the 3.57mm (9/64 ) holes for use with 8 gauge screws into aluminum. Carry out the same steps ( 1, 2 & 3 above) the same as 15mm (19/32 ) except using the 60mm (2-3/8 ) buttons. Copyright 2018 Eclipse Architectural 23 ALL DRAWINGS NO SCALE

24 NEW E3 SILLS WITH TWO LOCKING OPTIONS For 1-3/4 (44.5mm) or 2-1/4 (57mm) Door Thickness Flushbolt Twinpoint DBOT Series Flushbolt KT795 Sill NO SCALE Channel for 1-3/4 (44.5mm) door Channel for 2-1/4 (57mm) door KT775 Sill NO SCALE Twinpoint snap in covers for channels The new DBOT flushbolt & Twinpoint lock were designed to utilize the same channel in any of our four new E3 sills, thus giving you the option to now offer your customer the original flushbolt design or the simple hand rotation of the single handle, driving a 1 throw into the head and sill. ECLIE TWINPOINT LOCK & SWING HANDLE Specifications Minimum door thickness: 1-3/8 (35 mm) / Minimum rod length: 15 (381 mm) / Throw length: 1 (25 mm) / Uses: folding, french & sliding Twinpoint assembly is used in securing each pair of folding panels in the closed position. Not used on the swing (active) panel. twinpoint & swing handle twinpoint & swing handle Function The LT2 operates easily with a simple handle rotation, driving a 1 (25mm) throw into the head and sill. This makes it one of the most secure bolt locks on the market. An installed Twinpoint system is completely accessible and serviceable. For people with mobility impairments, the Twinpoint offers the security of two flushbolts, but without the access problems associated with flushbolts being too high or low to reach, and hard-to-grip door handles. Style LT2 has the sleek and clean styling synonymous with all Eclipse products. Their low profile allows any folding system, such as F3, E2, E3 or E4 to stack neatly, without intrusive door furniture getting in the way. Eclipse Twinpoint locks are fully concealed within the door stile, avoiding long or hardto-reach dropbolts fixed to the door face, particularly on tall doors. The Eclipse Twinpoint is an unobtrusive, functional and sleek locking solution. Testing The Centor LT2 has been tested to 100,000 cycles at maximum configuration to ensure smooth working order beyond their 10 year warranty period. The LT2 Twinpoint locking system has also been exposed to dust, mud, sand and corrosive atmospheres to ensure they stand up to real life use. This includes exposure to salt spray for seaside installations. 4L 3L twinpoint & swing handle multipoint & lever lock set 24 ALL DRAWINGS NO SCALE Copyright 2018 Eclipse Architectural

25 LT2 TWINPOINT LOCK & DF3 (ALUMINUM) OR DF4 (STAINLESS STEEL) SWING HANDLES Kit Components For Twinpoint Assembly transmission rod two finishes available on outer housing cover plate lock/gear box swing handle assembly (6 finishes) transmission rod PLEASE NOTE: When ordering complete TwinPoint Assembly, you are required to order: transmission rod & cover plate, lock/gear box, swing handle & cups. Twinpoint Lock assembly not available in PVD Brass (TG) PRODUCT # DESCRIPTION EC TwinPoint Lock (LT2 Model) for use with DF3 (Aluminum) & DF4 (Stainless Steel) Models ECLT2TRSN0924X TwinPoint transmission rod, cover plate and strike plate for 96 (2438mm) door height / brushed metallic aluminum finish ECLT2TRSN0924Y TwinPoint transmission rod, cover plate and strike plate for 96 (2438mm) door height / black anodized finish ECLT2TRSN0930X TwinPoint transmission rod, cover plate and strike plate for 120 (3048mm) door height / brushed metallic aluminum finish ECLT2TRSN0930Y TwinPoint transmission rod, cover plate and strike plate for 120 (3048mm) door height / black anodized finish EC Lock Gear Box for EC TwinPoint (LT2 Model) ECLT2NS Lock/gear box for EC TwinPoint transmission rod, cover plate & handle EC Swing Handle DF3 (Aluminum) Model For EC TwinPoint (LT2 Model) ECDF3SHNAL DF3 swing handle aluminum, black powder coat ECDF3SHNAPCN DF3 swing handle aluminum, satin aluminum powder coat ECDF3SHNAQ DF3 swing handle aluminum, bronze powder coat EC Swing Handle DF4 (Stainless Steel) Model For EC TwinPoint (LT2 Model) ECDF4SHNSOL DF4 swing handle stainless steel, PVD bronze finish ECDF4SHNSS DF4 swing handle stainless steel, brushed finish Cup for Sill or Head (Mandatory for Sill, Optional for Head) ECLTBC8SS Brushed S.S. Finish ECLTBC8SOL PVD Bronze Finish TL2 Router Bit ECLT2RB Router bit for LT2 TwinPoint Lock Assembly Eclipse E3 Drilling Jig for E3 Hinge placement on door KTE3DJ Eclipse E3 drilling jig for wood doors Strike Plate for Head (For replacement purposes only) One strike supplied with Twinpoint (Standard) ECLTSP8SS Brushed S.S. Finish ECLTSP8OL PVD Bronze Finish Copyright 2018 Eclipse Architectural 25 ALL DRAWINGS NO SCALE

26 LT2 TWINPOINT 1-1/16 (27mm) E3 Top Track Twinpoint assembly is used in securing each pair of folding panels in the closed position. Not used on the swing (active) panel. 4L 3L 4-23/32 (120mm) LT2 Model TwinPoint Lock Twinpoint & Swing Handle Twinpoint & Swing Handle Twinpoint & Swing Handle Multipoint & Lever Lock Set 15-3/4 (400mm) DF3 Model TwinPoint Swing Handle (Aluminum) or DF4 Model Twinpoint Swing Handle (Stainless Steel) Standard = 36 (914mm) Minimum = 15 (381mm) New E3 Sill used in conjuction with Twinpoint 1-3/4 (44.50mm) 4-23/32 (120mm) 1 (25mm) E3 Floor Channel used in conjunction with Twinpoint 26 ALL DRAWINGS NO SCALE Copyright 2018 Eclipse Architectural

27 WOOD STILE ROUTE PROFILE (OUTSWING APPLICATION) FOR LT2 MODEL 1/2 (12.7mm) 5/32 (4mm) 1-3/32 (27.80mm) Detail A 3/32 (2.5mm) 9/16 (14.4mm) Detail A /64 (1.8mm) 2-1/8 (54mm) 9/32 (7.1mm) 32/23 (18.4mm) ECLT2RB Route stile 1-3/4 (44.5mm) min 1-3/8 (35mm) A Back Set 1-1/32 (26mm) 1-7/64 (28mm) R7 9/32 (7.2mm) 11/16 (18mm) 15/32 (12mm) B R 1/2 (12.7mm) 14-11/64 (360mm) 9-1/16 (230.2mm) 4-61/64 (126mm) 3-3/16 (81mm) 2-5/64 (53mm) 13/64 (5mm) standard height 9/14 (36mm) A Copyright 2018 Eclipse Architectural 27 ALL DRAWINGS NO SCALE

28 E2 / E3 HINGE PLACEMENT OVER TWINPOINT 11/64 (4.2mm) 21/64 (8.4mm) 5/32" (4mm) 1-3/32" (27.8mm) E2 Hinge 9/16" (14.4mm) 1-3/4" (44.5mm) A A 1-3/4 (44.5mm) SECTION A-A E3 hinge R 13/32 (10.5mm) 1-11/16 (43mm) 13/16 (21mm) 2-13/32 (61mm) Strike plate for head ECLTSP8SS Brushed s.s. finish ECLTSP8OL PVD bronze finish Flushbolt metal cup used with floor channel ECLTBC8SS Brushed s.s. finish ECLTBC8SOL PVD bronze finish 19/64 (7.6mm) 28 ALL DRAWINGS NO SCALE Copyright 2018 Eclipse Architectural

29 DF3 TwinPoint Swing Handle, Choice of 4 Finishes Over Cast Aluminum Satin Aluminum Powder Coat Black Powder Coat Bronze Powder Coat LT2 TwinPoint Housing Cover Plate Finishes DF4 Twinpoint Swing Handle (SS) Choice of 2 Finishes Brushed Metallic Aluminum Black Anodized Aluminum Brushed stainless steel PLEASE NOTE: For technical reasons associated with color reproduction, the colors shown on this brochure give only an indication of color & finish. No warranty or guarantee can be given that they will exactly match the product as supplied. PVD bronze over stainless steel Finishes & Materials The Twinpoint door furniture is available in a range of finishes to suit any door or décor. Twinpoint Lock assembly not available in PVD Brass (TG) LT2 Model Twinpoint Swing Handle DF3: Aluminum handle (4 finishes) DF4: Stainless Steel Handle (2 finishes) Twinpoint assembly is used in securing each pair of folding panels in the closed position. Not used on the swing (active) panel. LT2 Transmission Housing Brushed Metallic Aluminum or Black Anodized finish 4L twinpoint & swing handle twinpoint & swing handle 3L twinpoint & swing handle multipoint & lever lock set Copyright 2018 Eclipse Architectural 29 ALL DRAWINGS NO SCALE

30 JAMB TO SILL ASSEMBLY jamb screws DS434 kerf seal KT768GASKET sill to jamb assembly gasket fir top moulding DS434 kerf seal inserts snap into channel E3 sill extruded aluminum clear or bronze anodized, with wood substrate and interior top moulding (fir) NO SCALE KT23BLVE PVC insert, black KT795COVERBLVE PVC insert, black KT23 OPTIONAL FLOOR CHANNEL APPLICATION FOR OUTSWING OR INSWING DOORS This application is recommended for interior application, exterior non-rainfall weather conditions or undercover well protected doors. 2-1/4 (57mm) door, outswing application shown. Other door thickness may be used. 2-1/4 (57mm) min door thickness when using floor channel is 1-3/8 (35mm) 1-3/4 (44.5mm) 7/16 (11mm) 7/8 (22mm) 1/2 (12.7mm) 7/16 (11mm) 7/8 (22mm) 3/16 (4.6mm) DS369A7145BL dual door bottom pile seals 13/32 (10mm) 13/32 (10mm) finished floor line finished floor line 7/8" (22mm) 15/16 (24mm) KT23DV Floor channel, bronze anodized with PVC insert, black KT23BLVE PVC insert only, black (replacement part) Lengths available: 111, 147, 183, 222, 294 (2.81m, 3.73m, 4.64m, 5.63m, 7.46m) 30 FULL SCALE EXCEPT AS NOTED KT23CV or KT23DV floor channel with PVC insert KT749 Flush bolt cup 7/8" (22mm) 15/16 (24mm) KT749 Flush bolt cup Door height plus 3-3/4 (95.3mm) = R.O. (from finished floor line) door height plus 3-1/4 (82.55mm) = full jamb height Copyright 2018 Eclipse Architectural

31 KT190C WOOD ASTRAGAL DETAIL FOR ECLIE E3 FOLDING SYSTEM Triple Seal For Superior Sealing Performance KT190C astragal supplied by Eclipse Architectural 2134mm (84 ) 2438mm (96 ) 2743mm (108 ) 3048mm (120 ) clear fir astragal 1-1/8 (28.5mm) 1-5/16 (33.34mm) kerf slot 1/8 x 3/8 (3.18mm x 9.5mm) NOTE: For ease of mounting all hardware, it is recommended to use square edge doors. NO SCALE 1-3/4 (44.5mm) door 9/32 (7.14mm) 1/8 (3.23mm) 3/8 (9.5mm) DS434 inserted weatherseal, brown, white or black DSP108 35BL Kerf inserted fin pile door with astragal DSP108 35BL Kerf inserted fin pile 3º bevel on active door ie: 35-7/8 (911mm) inside measurement width of door. 36 (914.4mm) outside measurement of door 5/32 (4mm) 9/32 (7.14mm) 1/8 (3.23mm) 5/16 (7.94mm) LATCHING DOOR HOLD (DH) NO SCALE T-Unit NO SCALE KT740DHC KT740DHD Clear anodized Bronze anodized set screen adjustment screw main unit Copyright 2018 Eclipse Architectural FULL SCALE EXCEPT AS NOTED 31

32 E3 HARDWARE PLACEMENT (4L) Outswing Application C3 DOOR HOLD MAGNETS (OPTIONAL) end carrier intermediate carrier top pivot weatherseals KTE3TPPLATE mounting plate for E3 top pivot assembly bottom pivot wall pivot hinge concealed intermediate guide hinge with handle concealed end guide KTDCAS Satin aluminum finish KTDCAOL Black finish KTDCATG Brass finish (custom order, call for manufacturing time) APPLICATIONS: HOW TO DETERMINE SWING OF SYSTEMS The following is a guideline when determining outswing or inswing applications for the purpose of choosing correct hardware and flushbolts. NOTE: The interior/exterior designation (i.e. 3L) is still used for interior application because it just makes it easier to understand. FOR EXAMPLE: (FLUSHBOLT) BEDROOM SIDE (FLUSHBOLT) BEDROOM SIDE 3L OUTSWING 3LI INSWING Hall Or Living Room The above example (3LI) shows the system swinging into the bedroom and flushbolts on the same side. This would be an inswing system and the bedroom side is considered the interior side. Passage set only recommended for the swing door. Another Room The above example (3L) shows the system swinging into another room and flushbolts on the bedroom side. This would be an outswing system and the bedroom side is considered the interior side. Passage set only recommended for the swing door. 2L2R Not accessible The above example (2L2R) is not recommended for interior applications because of the potential of getting locked in a room without any exit. Other configurations not recommended. 2L, 2R, 4L, 4R, 6L, 6R, 8L, 8R; basically pairs or even number or door panels. 32 ALL DRAWINGS NO SCALE Copyright 2018 Eclipse Architectural

33 MAGNETS KTEMAG Magnets for holding the door panels in the open position FLUSHBOLT PLACEMENT Suggested flushbolt lengths for door heights 80 to 118 (2032mm to 2997mm) 3L 2-3/8 (60.3mm) 13/16 (20.6mm) KTEMAG (sold as pairs) NOTE: End user may require longer flushbolts for top of doors for easier reach. When using E2 hardware for folding windows, top flushbolt length must be specified. Scale: 1/4 = 1ft. 8 (200mm) flushbolt 16 (400mm) flushbolt 24 (600mm) flushbolt 39 (1000mm) flushbolt up to 84 (2134mm) 84-1/16 to 96 (2159mm to 2438mm) 96-1/2 to 108 (2403mm to 2743mm) 108-1/16 to 118 (2768mm to 2997mm) magnets I.E. 5L door hold 8 (200mm) flushbolt 8 (200mm) flushbolt 8 (200mm) flushbolt 8 (200mm) flushbolt MANUAL DOOR CALC Clearances Pivot door to jamb 9/32 (7mm) Swing door to jamb 9/32 (7mm) Panel to panel gap 5/32 (4mm) Bottom of door panel to sill 3/8 (9.5mm) Top of door panel to header 3/16 (5mm) Inside face of door panel to stop 3/8 (9.5 mm) Rough opening specs for E3 1. Door Height plus 5 (127mm) = R.O. when using inswing or outswing E3 Sills and Frame specs. 2. Door Height plus 4-1/4 (107.9mm) = R.O. when using KT788E3 ADA Sill. 3. Door Height plus 3-3/4 (95.25mm) = R.O. when using E3 floor channel. Manual calculation for determining R.O. (i.e. configuration 1L3 R, i.e. door panel size 36 x 84 [914mm x 2134mm]) R.O WIDTH 1) Jamb to Stud - typical 1/4 (6mm) shimming x 2 =.5 (12mm) 2) Jamb thickness 11/16 (17.5mm) x 2 = (34.9mm) 3) Panel to Jamb - Clearance 9/32 (7mm) x 2 =.5624 (14mm) 4) Panel to Panel - Gap 5/32 (4mm) x 3 =.4686 (12mm) 5) Panel width 36 (914 ) x 4 = 144 (3656mm R.O. (width) /32 or or (3731mm) or (3.73m) For O.S.M. width of unit take R.O. minus 1/2 (12mm) i.e /32 (3731mm) - 1/2 (12mm) = /32 (3718mm). R.O. 7 8 EXT INT. HEIGHT 6) Frame header to R.O. header. Typical 1/2 (12mm) shimming x 1 =.5 (12mm) 7) Frame header 2-21/32 (68mm) x 1 = (68mm) 8) Top of door panel to frame header 3/16 (5mm) x 1 =.1875 (5mm) 9) Door panel height 84 (2134mm) x 1 = 84 (2134mm) 10) Bottom of door panel to top of sill 13/32 (10mm) x 1 =.3937 (10mm) 11) Sill height 1-3/16 (30.16mm) x 1 = (30.16mm) R.O. Height 88 15/16 or or (2259 mm) or (2.25m) For O.S.M. height of unit take R.O. minus 1/2 (12mm). i.e /16 (2259mm) minus 1/2 (12mm) = 88-7/16 (2246mm). Copyright 2018 Eclipse Architectural 33 ALL DRAWINGS NO SCALE

34 E3 PARTS SELECTION When ordering, add color designation (letters) to end of product number: OL: pvd bronze S: stainless steel TG: pvd brass PVD brass (TG) finish is custom order, call for manufacturing time. KTE3C Pivot sets 2 pieces KTE3 Wall pivot set, jamb mounted middle pivot for doors over 88 (2235mm) 1 piece KTE3CLCS Left carrier sets 2 pieces KTE3CRCS Right carrier sets 2 pieces KTE3C Intermediate carrier sets, 3 pieces mounted between top & bottom pivot KTE3CBPIVOTH bottom pivot housing only (replacement part) concealed bottom guide concealed bottom guide concealed bottom guide KTE3EH Interior D pull handle for inswing doors 1 piece KTE3 Hinge sets (FLAT) with middle handle for outswing doors 3 pieces KTE3HN Hinge sets (FLAT) without middle handle for inswing doors 3 pieces KTE3 Half OFFSET hinge sets with middle handle for outswing doors 3 pieces KTE3HHN Half offset hinge sets without middle handle for inswing doors 3 pieces Intermediate carrier sets with additional hinge Hinge sets with handle for outswing doors Hinge sets no handle for inswing doors Half offset hinge sets with handle for outswing doors Half offset hinge sets no handle for inswing doors KTE3HNH Single hinge, order separately KTE3HNH Single hinge, order separately KTE3HNH Single hinge, order separately KTE3HHNH Single hinge, order separately KTE3HHNH Single hinge, order separately concealed bottom guide 34 ALL DRAWINGS NO SCALE Copyright 2018 Eclipse Architectural

35 E3 PARTS SELECTION PVD brass (TG) finish is custom order, call for manufacturing time. Pivot Set Wall Pivot Set Use with above pivot set on doors over 8ft (2438mm) in height 2 pieces KTE3CTG PVD brass KTE3COL PVD bronze KTE3CS stainless steel 1 piece KTE3TG PVD brass KTE3OL PVD bronze KTE3S stainless steel Replacement Screws for all hinges KTE3SCREWTG PVD brass KTE3SCREWOL PVD bronze KTSCREWSS stainless steel Number of Hinges for Panel Heights of 80 to 118 (2032mm to 2997mm) Intermediate carrier sets Hinge set or half offset hinge set Pivot set top & bottom #1 Half Offset Hinge Set Middle hinge with handle for outswing doors 3 pieces KTE3TG PVD brass KTE3OL PVD bronze KTE3S stainless steel #1 #1 #2 #2 #2 Hinge Set (Flat) Middle hinge with handle for outswing doors 3 pieces KTE3TG KTE3OL KTE3S PVD brass PVD bronze stainless steel #3 #3 #4 #4 #3 #4 Intermediate Carrier Set 3 pieces KTE3CTG PVD brass KTE3COL PVD bronze KTE3CS stainless steel #5 #5 #5 Right Carrier Set Left Carrier Set 2 pieces KTE3CRCSTG PVD brass KTE3CRCSOL PVD bronze KTE3CRCSS stainless steel 2 pieces KTE3CLCSTG PVD brass KTE3CLCSOL PVD bronze KTE3CLCSS stainless steel Up to 96 (2438mm) door height use 1, 3, /16 to 108 (2440 to 2743mm) use 1, 2, 3, /16 to 118 (2745 to 2997mm) use 1, 2, 3, 4, 5 Up to 96 (2438mm) door height use 1, 3, /16 to 108 (2440 to 2743mm) use 1, 2, 3, /16 to 118 (2745 to 2997mm) use 1, 2, 3, 4, 5 Up to 87-15/16 (2234mm) door height use 1 & 5 88 to 96 (2235 to 2438mm) door height use 1, 3, /16 to 108 (2440 to 2743mm) door height use 1, 2, 3, /16 to 118 (2745 to 2997mm) door height use 1, 2, 3, 4, 5 Single Hinge Half Offset No handle for inswing doors. Use as 4th & 5th hinge for doors over 8ft (2438mm) in height. 1 piece KTE3HHNHTG PVD brass KTE3HHNHOL PVD bronze KTE3HHN stainless steel Hinge Set (Flat) No middle handle for inswing doors 3 pieces KTE3HNTG PVD brass KTE3HNOL PVD bronze KTE3HNS stainless steel Single Hinge (Flat) No handle for inswing doors. Use as 4th & 5th hinge for doors over 8ft (2438mm) in height. 1 piece KTE3HNHTG PVD brass KTE3HNHOL PVD bronze KTE3HN stainless steel Single Hinge Half Offset With handle for outswing doors. Use as 4th & 5th hinge for doors over 8ft (2438mm) in height 1 piece KTE3HHTG PVD brass KTE3HHOL PVD bronze KTE3 stainless steel Half Offset Hinge Set No middle handle for inswing doors 3 pieces KTE3HHNTG PVD brass KTE3HHNOL PVD bronze KTE3HHNS stainless steel Single Hinge (Flat) With handle for outswing doors. Use as 4th & 5th hinge for doors over 8ft (2438mm) in height 1 piece KTE3HTG PVD brass KTE3HOL PVD bronze KTE3 stainless steel Copyright 2018 Eclipse Architectural 35 ALL DRAWINGS NO SCALE

36 Exterior Folding Door Systems Head Office & Manufacturing Centre, Vancouver, Canada 7470 Buller Avenue, Burnaby, B.C. V5J 4S5 Canada Phone: (604) Fax: (604) Outside Vancouver, B.C., please use our toll free numbers: Phone: Fax: Branch Office & Distribution Centre, Toronto, Canada Phone head office toll free for branch address Branch Office & Distribution Centre, Los Angeles, California Phone head office toll free for branch address Eclipse Architectural Corporate Showrooms Vancouver & Toronto, Canada Los Angeles, California, USA