Spitfire Mk.IX ARF. Electric retract system. TopRCModel-USA.com

Size: px

Start display at page:

Download "Spitfire Mk.IX ARF. Electric retract system. TopRCModel-USA.com"

Rudolph Woods
6 years ago
Views:

Electric retract system Thank you very much for purchasing our TRCM optional electric retract set, all our products were passed strict QC before they shipped out to the customers.

1 Electric retract system Thank you very much for purchasing our TRCM optional electric retract set, all our products were passed strict QC before they shipped out to the customers. In order to avoid probably trouble happen, we still would like you to follow the steps below before you assemble our electric retracts to your plane.. Connecting the circuit board to the battery and receiver. Spitfire Mk.IX ARF. Turn on the radio control to check the lights on the circuit board, if the lights turn on green or turn on red orderly 0. second after each from the right to the left and all the lights will turn off after seconds, then the circuit will work normally. Otherwise the circuit will be a defective one if you make sure the setting on your radio control are correct, please don't use it but contact with your supplier in time.. Link the electric retract units to the circuit boards after the above two steps, check again the electric retracts to see if they can work normally or not. In order to let the customers have more choices, we don't provide a uniform plugs. For retracts Receiver Specification: Wing Span: 0mm/in Length: 7mm/7.in Flying Weight: ~7.kg Wing area: 7.9 dm Engine: cc-0cc R/C System:.Ghz ch Servo: GP *7 ; EP * Battery: LI-PO S* 000mAh 0C ESC: 0A High voltage Brushless ESC TopRCModel-USA.com INSTRUCTION MANUAL 7.V 0C. Assemble the electric retracts to the plane after several times smoothly running. Please don't ceaselessly turn and off the switch in seconds, if you do this way, the circuit board will be heated..v For receiver SAFETY PRECAUTIONS This R/C airplane is not a toy! (The people under years old is forbidden from flying this model) First-time builders should seek advice from people having building experience.if misused or abused,it can cause serious bodily injury and damage to property. Fly only in open areas and preferably at a dedicated R/C flying site. We suggest having a qualified instructor carefully inspect your airplane before its first flight.please carefully read and follow all instructions included with this airplane,your radio control system and any other components purchased separately.

2 Accessories packing list Gasoline tube channel radio for aiplane is highly recommended for this model. cc gas engine. in scale spinner Engine 9 X0 Motor X 9 Optional electric retract set Gasoline TP Screw (.xmm) TP Screw (.xmm) TP Screw (x0mm ) Screw (.xmm) Screw (xmm) Screw (x0mm) Screw (xmm) Screw (x0mm) Screw (x0mm) Screw (xmm) Washer(x0mm) Locknut (mm ) Washer(xmm) Washer(xmm) Linkage Stopper Push rod (xmm) Push rod (x70mm) Plastic tube (x0mm) Steel wire (0.x000mm) Gear door Servo tray(mm) Canopy Fiberglass Canopy PVC Fiber deconations scoop Antenna Scale gun set Main wing joiner(0x0mm) carbon fiber tube(0xmm) Tail gear Alu clevis Tail wheel (mm) Motor: Outer rotor, -0 0KV We strongly recommen you use the thread lock for all the screws when you build your model. (mm) (mm) Clevis pivot & round hinge(xmm) Pin hinge(xmm) Screw (x0mm) EVA(0mm) Push rod Optional box for motor Ply sheet (mm) Fuel tank (0cc) Purchased separately Main wheels (00mm) Oleo struts Circlip Retracts strut circuit board

3 0 Assemble the canopy to the cockpit with screws. Epoxy the fiber deconations to aprropriate position on the bottom of the wing. Assemble the aileron to main wing with instant type AB glue. Be careful to ensure the moving parts of the hinges are able to move freely. TP Screw (.xmm).mm TP Screw (.xmm) 00mm mm Pivot & round hinge(xmm) Clevis mm) Push rod mm) Screw (x0mm) Locknut (mm ) Washer(xmm) Screw (xmm) Washer(xmm) Screw (xmm) Servo tray(.x.xmm) Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! Assemble the cockpit to the fuselage. The centre of the Gravity. Apply instant AB glue to aileron and pin hinge. Install the s to the servo of aileron as illustration below. Pivot & round hinge(xmm) Screw (xmm) 0 mm Washer (xmm) 0 mm Screw (xmm) Make sure hinges are mounted in the same line. Washer(xmm) Assemble the scale gun set to the wing and the fiber scoop to the fuselage. The skech map of the Spitfire plane install completion. Keep some space about mm width between the trailing edge and the aileron. Install the nylon control horn and connect the linkage. Scale gun set Screw (x0mm) scoop Trailing edge Aileron Cut away the rubber tube when the epoxy glue dried. Screw (x0mm) Screw (x0mm) Push rod mm) Washer(xmm) Lock Nut (mm ) Washer(xmm) Blind Nut Scale gun set Make sure they are in the right position while installing. mm Lock Nut (mm ) Screw (x0mm) Nut (mm ) Washer(xmm)

4 Secure the servo.install the nylon control horn and connect the linkage. TP Screw (xmm) Epoxy the pin hinges to the slots in the flap. Fix the ply sheet as illustration with screw from the fuselage to stop the battery from moverable. Ply(mm) Blind Nut Canopy (Fiberglass) Screw (xmm) Canopy (PVC) TP Screw (xmm) Pin hinge(xmm) Battery Ply(mm) Screw (xmm) Fiber deconations scoop Antenna Scale gun set TP Screw (.xmm) Screw (x0mm) 7 Assemble the servo tray to the wing with screws and epoxy the fiber horn to the aileron. 9 Keep some space about mm width between trailing edge and flap. Assembly of the fuel tank(please notice that the plug of the tank and the tube should special for gasoline. Assemble the antenna to the fuselage with screw. TP Screw (.xmm) Trailing edge Antenna.mm Flap Screw (x0mm) Masking tape TP Screw (.xmm) Make sure they are in the right position while installing. mm Fuel spray line Air pressure line Fuel supply line Antenna Screw (x0mm) 0 Epoxy the flaps to the wings as illustration. 7 Mount the fuel tank, battery and receiver to the fuselage. 9 Cut off the surplus part from the PVC canopy, glue the fiberglass pic to the PVC canopy and trim off the surplus part. Pin hinge(xmm) Clevis mm) Push rod mm) Screw (x0mm) Locknut (mm ) Washer(xmm) Screw (xmm) Washer(xmm) Screw (xmm) Servo tray(.x.xmm) Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! A PVC Fiberglass PVC B C Fiberglass

5 Reinforce blocks to the the engine engine mounts mount by from epoxy inner the and wooden 9 the engine mount as illustration. outer of Customer can also use electric motor as optional, the assemble process is from step to step. The side view when motor install completion. Install the s to the servo of flap as illustration below. Assemble the servo tray to the wing with screws and epoxy the fiber horn to the flap. mm Screw (xmm) TP Screw (.xmm) Washer (xmm).mm Screw (xmm) Washer(xmm) Masking tape TP Screw (.xmm) 0 Install the engine to the engine mount with screws. Remove the firewall off from the engine mount as illustration. Install the nylon control horn and connect the linkage. Screw Screw (x0mm) Screw (x0mm) Push rod mm) Washer(xmm) Lock Nut (mm ) Washer(xmm) Screw (x0mm) Nut (mm ) Washer(xmm) Lock Nut (mm ) Gear door Screw (x0mm) TP Screw (x0mm) TP Screw (.xmm) Main wing joiner(0x0mm) Main wheels (00mm) Oleo struts Circlip Retracts strut circuit board Using scotch tape, one side of it fixed, cover the blind nut hole and mark where the blind nut holes are.put the cowl to it is place on the fuselage, base on the marks on the scoth tape drill holes to the cowling. Epoxy the optional box to the engine mount and put the battery to the box from the hatch on the fuselage. Secure the servo.install the nylon control horn and connect the linkage. Mount the gear door and the wheel to the retract. Screw (xmm) stainless steel rod Circlip mm Battery Main wheels (00mm) Screw (x0mm) Washer(xmm) Optional box for motor TP Screw (xmm) Retracts strut Note:rubber wheels oleo struts and retracts are optional. 0

6 Assemble in the gear the house. retracts to the appropriate position 9 The sketch map of the wing fits well to the fuselage. The sketch map of the steel wires working in the fuselage. 7 Assemble the tail gear cover with screws as below. TP Screw (x0mm) Rudder servo TP Screw (.xmm) Tail wheel servo Rudder servo TP Screw (.xmm).mm TP Screw (x0mm) TP Screw (.xmm) TP Screw (.xmm) 7 Drag the servo line and retracts lines from the wing. 0 Factory already set blind nuts in the wings, the customers can fix the wing to the fuselage by tightening the nylon screws. The sketch map of the steel wires connection out of the fuselage. Main wing joiner(0x0mm) Main wing joiner(0x0mm) Screw (x0mm) Screw (x0mm) Linkage Stopper Plastic tube (x0mm) Fuel tank (0cc) Ply sheet (mm) Screw (xmm) Screw (x0mm) Washer(xmm) Connect the two wings through the main wing joiners. The sketch map should be when the stabilizer assembly completion. Take off the tail wheel and trim a slot on the tail cover for assembling the tail wheel. The side view when the engine install completion. Make sure to glue securely. If not properly glued, a failure in flight may occur. Securely glue together.if coming off during flights, you'll lose control of your airplane which leads to accidents! Temporarily fasten down the main wing and check its correct position. mm B A A' B' A=A' B=B' 9

7 The sketch map when assemble the tail landing gear to the wheel steeling mount. Assemble the steel wires well to the rudder horn and tail wheel. Epoxy the elevator to the stabilizer. Steel wire (0.x000mm) Collar Tail wheel (mm) Clevis Screw (x0mm) Washer(xmm) Steel wire (0.x000mm) Alu clevis Locknut (mm ) Screw (x0mm) Washer(xmm) Lock Nut (mm ) Steel wire pivot & round hinge(xmm) 9 Washer(x0mm) Screw (.xmm) carbon fiber tube(0xmm) Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! 9 The sketch map of the tail wheel and steel wires working in the fuselage. Install the servo. Apply instant type AB glue to elevator and hinges. Glue the wooden block to each side of the stab tube as below, put the stab tube into one side the horizontal to the end and mark it out at the root of the horizontal, drill a hole in the stab tube and horizontal as illustration. Screw (x0mm) Washer(xmm) pivot & round hinge(xmm) Steel wire Lock Nut (mm ).mm Clevis Screw (x0mm) Locknut (mm ) Washer(xmm) Steel wire (0.x000mm) Make sure hinges are mounted in the same line. carbon fiber tube(0xmm) mm mm mm mm 0 Fix the tail gear to the tail fuselage. Connect the steel wires of the rudder horn and tail gear to the servo. Keep some space about mm width between elevator and tailing edge. Fix the carbon fiber tube to one side of the stab with screws. Tailing edge Screw (.xmm) Washer(x0mm) Screw (.xmm) Elevator Cut away the rubber tube when the epoxy glue dried. mm mm Screw (.xmm) Make sure they are in the right position while installing. Washer(x0mm) Screw (.xmm)

8 7 Assemble the stab to the fuselage drill a hole to the other section stab. 0 Epoxy the pivot & round hinges to the rudder. Assemble the push rod branches to the horns on the elevator..mm Clevis(mm) Screw (x0mm) Locknut (mm ) Washer(xmm) Linkage Stopper Push rod Steel wire (0.x000mm) Tail wheel (mm) Tail gear Alu clevis TP Screw (.xmm) EVA(0mm) TP Screw (.xmm ) Screw (x0mm) Washer(xmm) Screw (x0mm) Locknut (mm ) Washer(xmm) Lock Nut (mm ) pivot & round hinge(xmm) Make sure hinges are mounted in the same line. Fix the other side of the stab with screw. Epoxy the rudder to the vertical fin. The sketch map of the push rod connect to the elevator servo. Assemble the servos. Screw (.xmm) Washer(x0mm) Screw (x0mm) Washer(xmm) Set screw (xmm) mm Set screw (xmm) Lock Nut (mm ) Adjustable Rod Push rod Adjustable Rod Washer (mm) Nut (mm) Linkage Stopper Washer(x0mm) Screw (.xmm) Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! mm Rod Washer (mm) Nut (mm) Washer (mm) Nut (mm) Set screw (xmm) 9 The sketch map should be when the stabilizer assembly completion. Epoxy the fiber horns to the slots in the rudder and elevator. The sketch map of the push rod working in the fuselage. 7 Assemble the another side of the push rod to the elevator servo in the fuselage as image. Make sure to glue securely. If not properly glued, a failure in flight may occur. Securely glue together.if coming off during flights, you'll lose control of your airplane which leads to accidents! Temporarily fasten down the main wing and check its correct position. B A A' B' EVA(0mm) A=A' B=B' EVA(0mm) 7

F - 4u Corsair (50cc)

F - 4u Corsair (50cc) F - u Corsair (50cc) Specification: Length: 73(.3") Wing span: 0mm(5") Wing area: 7.00sq.dm(9.39sq.ft) Wing loading: 35.g/sq.dm(.5oz/sq.ft) Flying weight:.kg(.0lbs) Radio: ch & 0servos Engine: 50cc gasoline