Specifications. Before commencing assembly, please read these instructions thoroughly.

Transcription

1 INSTRUCTION MANUAL Before commencing assembly, please read these instructions thoroughly. Specifications Wing Span: 8.5 in / 30 mm Wing Area: 330 sq in /.3 sq dm Flying Weight: 6 oz / 70 g Fuselage Length: 30.5 in / 760 mm Requires : Speed 00 motor, - channel radio w/ micro servos, 5A speed controller and 7-8 cells 000 mah battery Warning! This model is not a toy. It is designed for maximum performance. Please seek advice if one is not familiar with this kind of electric powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference. * Specifications are subject to change without notice.* THE WINGS MAKER FACTORY PRE-FABRICATED ALMOST-READY-TO-FLY (ARF) SERIES MADE IN CHINA www. thewingsmaker. com GE06

2 INDEX BEFORE YOU BEGIN PARTS LIST ASSEMBLY SAFETY PRECAUTIONS P. P. P.3-P.0 P. 0 BEFORE YOU BEGIN 3 Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts, but will not extend to the parts that are good before gluing to defective parts during assembly. Warranty will not cover any parts modified by customer. Symbols used throughtout this instruction manual comprise of the following :- Apply epoxy glue. Apply instant glue (C.A.glue, super glue.) Apply thread locker Must be purchased separately! Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling. Peel off shaded portion covering film. Cut off shaded portion. 3mm Drill holes with the specified diameter (here: 3mm). Pierce the shaded portion covering film. Pay close attention here! Warning! Do not overlook this symbol! P.

3 Parts List. MAIN WING -- pair. PUSHROD Ø.x70mm w/ Threads (For Aileron) -- pcs HORN -- sets CLEVIS -- pcs STRAPER -- pcs FUEL TUBE Øxmm -- pcs SCREW PMx8mm -- pcs 3. PLYWOOD 5x3x8mm(Wing Joiner) -- pc.. STABILIZER & ELEVATOR -- set FUSELAGE -- pc. ELEVATOR LINK PL pc. SCREW PMx8mm -- pcs 5. VERTICAL FIN & RUDDER -- set 6. TAIL LANDING GEAR -- set SCREW PAx8mm -- pcs BALSA 3x6x7mm -- pc. SCREW PMx8mm -- pc. M NUT -- pc. AI REINFORCEMENT PLATE -- pc. 7. FUEL TUBE Øxmm -- pc. CLEVIS -- pc. PUSHROD Ø.x5mm w/ Threads(For Elevator) -- pc. 8. PUSHROD Ø.x0mm w/ Threads(For Rudder) -- pc. FUEL TUBE Øxmm -- pc. CLEVIS -- pc. HORN -- set SCREW PMx8mm -- pcs 9. SPEED 00 MOTOR -- set GEAR BOX -- set PROPELLER -- pair SPINNER Ø36mm -- set COWLING -- pc. DUMMY ENGINE COVER -- pair MOUNT PLATE (PL05) -- pc. SCREW PWAx8mm -- pcs WASHER dxd5mm -- pc. M NYLON INSERT LOCK NUT -- pc. SCREW PMx0mm -- pc. 0. WIND SHIELD & SIDE WINDOWS -- set SCREW PWAx8mm -- pcs. SPONGE 0x50x50mm -- pc. DOUBLE-SIDED TAPE 30x35mm -- pc. FUEL TUBE Øxmm -- pcs BATTERY TIE -- pc. STRAPER -- pcs. MAIN LANDING GEAR -- set MAIN WHEEL Ø50mm-- pcs LANDING WIRE STRAPS (PL030) -- 3 pcs PVC PLATE 0.5x6x3mm (For Main Landing Gear) -- pcs BALSA x73x80mm (Main Landing Gear Cover) -- pcs SCREW PA.6x0mm -- 6 pcs COLLAR Ø.6mm w/ set screw -- sets SCREW PMx6mm -- pcs WASHER dxd5mm -- pcs M NUT -- pcs TRANSPARENT DECALS 0x70mm -- pcs 3. SCREW PM.5x5mm -- pcs WASHER d.6xd7mm -- pcs BALSA 6x5x8mm (Wing Protection) -- pc.. SCREW PA.3x8mm -- 6 pcs MAIN WING STRUTS -- pair 5. DECALS -- set P. COVERING:-- LIGHTEX SGX 33 CUB YELLOW

4 Main Wing Aileron Servo lead Bottom View Apply instant type CA glue to both sides of each hinge. Aileron Servo Ømm pilot holes for The Wings Maker tri-horn are pre-drilled. Please look for pin-hole marks at under side of control surfaces. PMx8mm Screw Straper mm mm Bottom View PMx8mm Fuel Tube dxdxmm Clevis Plywood 3x6xmm Pushrod Ø.x70mm Horn mm 3 Main Wing Please dry fit wing joiner into left and right wing to make sure they fit with the proper dihedral angle, mark the wing joiner if necessary. Apply epoxy glue to both sides of all surfaces in contact. Use a stick to apply the glue to inner side of wing joiner sleeve, and apply the glue to wing joiner before putting them together. Wing joiner not glued properly will lead to wing failure and plane crash. Wing Joiner 5x3x8mm P.3

5 Stabilizer & Elevator PMx8mm Screw (Stabilizer) (Main Wing) B B' Temporary install the main wing, adjust leveling of the stabilizer to make it as parallel to the main wing as possible. *Also refer to step 5 Wing Setting A A=A A mm Completed PMx8mm Ømm pilot holes for Wings Maker tri-horn are pre-drilled. Please lood for pin-hole marks at under side of control surfaces. Apply instant type CA glue to both sides of each hinge. 5 Vertical Fin & Rudder C C C= C Completed Balsa 3x6x7mm Apply instant type CA glue to both sides of each hinge. 6 Tail Landing Gear PA x 8mm Screw PM x 8mm Screw.6mm Collar M Nut mm mm PAx8mm Plastic Collar M Nut PM x 8mm Bottom View Ai Reinforcement Plate P.

6 7 Elevator Pushrod 3mm 70mm Pushrod Ø.x5mm Clevis Fuel Tube dxdxmm Bottom View 8 Rudder Pushrod PM x 8mm Screw Ømm pilot holes for The Wings Maker tri-horn are pre-drilled. Please look for pin-hole marks at side of control surfaces. Pushrod Ø.x0mm 65mm 0mm Clevis mm Horn Bottom View Fuel Tube dxdxmm PM x 8mm P.5

7 9 Motor / Cowling Setting M.6 x 7mm Socket Head Screw PM x mm Screw PM x 0mm Screw PWA x 8mm Screw PA.6 x 8mm Screw 3mm Set Screw d x D5mm Washer 3 M Nylon Insert Lock Nut Speed 00 Motor 3 Gear Box M Nut M.6 x 7mm Washer d x D5mm PM x mm M NUT Top View TO ALLOW FOR BACKLASH OF MATCHING GEAR, PUT A PIECE OF THIN PAPER BETWEEN THE GEARS AND THEN TIGHTEN THE M.6X7mm SCREWS. REMOVE THE PAPER BEFORE FLYING. 5 Battery Battery Tie Bottom View 7 PM x mm 6 8 PM X 0mm dxd5mm Washer mm M Nylon Insert Lock Nut DUMMY ENGINE COVER Bottom View PM x mm Don't over-tighten the PM screws, let the propeller blades align themselves when spinning. 9 0 PWA x 8mm PA.6 x 8mm 3mm Set Screw Steel Wire Ø.x35mm.5mm Spinner P.6

8 0 Canopy PWA X 8mm Screw.5mm PWA X 8mm Radio Equipment Rudder Pushrod Ø.x0mm Rudder Servo 5A Speed Controller Battery Battery Tie Straper Elevator Pushrod Ø.x5mm Receiver wrapped up in sponge Fuel Tube dxdxmm Elevator Servo Double-Sided Tape P.7

9 Main Landing Gear PA.6x0mm Screw 6.6mm Collar PMx6mm Screw dxd5mm Washer M NUT Washer dxd5mm PA.6x0mm M NUT.5mm PVC PLATE Front Wheel Ø50mm.6mm collar PMx6mm 3mm set screw 0x70mm TRANSPARENT DECALS 3 Main Wing PM.5x5mm Screw d.6xd7mm Washer Wing Protection d.6xd7mm PM.5x5mm Wing Struts PA.3x8mm Screw 6 mm mm PA.3x8mm P.8

10 5 Wing Setting Adjust the wing and fuselage configuration as shown in the diagrams. A A ' B C C ' B ' A =A ' B =B ' C =C ' P.9

11 6 Control Throws Rudder Elevator 5mm 5mm 5mm 5mm Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference. Aileron 0mm 0mm 7 C.G. The ideal C.G. position is 50mm (.0 in.) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying. 50mm.0in. C.G. Warning! Important Safety Precautions #First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary. #Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft. # is specially designed to be powered by Speed 00 geared motor. #Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running propeller. #If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles. Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone. Too hot an iron may damage the covering. #Check and re-tighten up all factory assembled screws, use thread locker if necessary. GE P.0

12 www. thewingsmaker.com GE THE WINGS MAKER