E-AERO EPP PITTS KIT From BP HOBBIES. Parts Included in kit

Size: px
Start display at page:

Download "E-AERO EPP PITTS KIT From BP HOBBIES. Parts Included in kit"

Transcription

1 E-AERO EPP PITTS KIT From BP HOBBIES Parts Included in kit

2 Thank you for purchasing the BP Hobbies/E-aero EPP Pitts. Please take the time to read through the instruction manual before beginning the build. If you have had little or no experience working with EPP foam it requires some patience to work with it. Although the Pitts is not hard to build, it is certainly different than building a balsa or EPS foam plane. A few things about EPP foam. There are only a few glues that will stick to EPP. Regular CA, thin, medium and thick will stick well when used with accelerator. Hot melt glue sticks well but can not be left in a hot car as the high heat will soften the glue. Epoxies, white glue and foam safe CA do not work on EPP foam. Put a brand new sharp blade in your hobby knife. Dull knives do not work well with EPP foam. To paint the Pitts we used Krylon brand indoor/outdoor spray paint and stencils made from card stock. You will need these additional items to complete the kit. 2oz bottle of medium CA 2oz bottle of thin CA 4oz bottle of accelerator Hot melt glue gun Sharp hobby knife 4-9 gram servos 4 channel receiver BPA motor mah 11.1 volt lipo battery 1- BP 18A amp speed controller Heat gun Clear duct tape 2 packages of DuBro part # 845 mini E/Z connector. 8x6 APC propeller 8 inch Y connector Velcro Spray paint

3 Step 1 Using hot melt glue or medium CA glue the rear top section of the fuse together. If you are using hot melt glue do not leave the airplane in a hot car for long periods of time. The heat will soften the hot glue causing a glue failure at the joint. I prefer to use medium CA and accelerator. Step 2 Hold the two halves together with tape until the glue sets. Step 3 Glue the front top section of the fuse together using medium CA and kicker.

4 Step 4 Using medium CA glue the fuse rear bottom section to one of the sides making sure that there is a 90 degree angle between the side and the bottom. Step 5 Glue the other fuse side to the rear bottom piece. Step 6 Glue the lower front fuse sides together.

5 Step 7 Use a little force to pull the two sides together and hold until the glue sets. Step 8 It should look like this when completed. Step 9 Using ONLY hot melt glue apply a good amount of it in the grove where the landing gear wire will be installed.

6 Step 10 While the glue is hot force the landing gear wire into the slot. Hold the wire in place until the glue sets. Step 11 Apply hot melt glue to the landing gear cover. There are small notches in the foam piece to aid you in positioning the two pieces. Step 12 Put the two pieces together and hold them until the glue sets.

7 This is what it should look like when finished. Step 13 Bevel the shaded area with a hobby knife. Step 14 Bevel the shaded area with a hobby knife

8 Step 15 Apply hot melt glue to the shaded area.

9 Step 16 Before the hot melt glue sets, place the landing gear block into the fuse and hold it until the glue sets. Step 17 Apply hot melt glue to this area. Hold them together until the glue sets.

10 Step 18 Apply medium CA to the front foam firewall as shown. Step 19 Push the firewall in until it is flush with the fuse sides. Spray the assembly with accelerator and hold until the glue sets. Spray the inside of the fuse and firewall with accelerator to set the glue.

11 Step 20 Using CA glue the fuse sides together where the vertical fin will go. Step 21 Use a hobby knife to trim the fuse end square and cut a flat spot on the top of the fuse to accept the vertical fin. Step 22 Get the 4 top wing sections and lay them out. The top wing has the two swept back center section and two end sections. The two end sections DO NOT have cut outs for the aileron servos.

12 Step 23 The two lower wing center sections have dihedral cut into them. DO NOT confuse these with the two top pieces without dihedral. The two lower wing outer panels have cut outs in them for servos. Step 24 Glue the inner panels to the outer panels using medium CA. Do this for both the bottom and top wings. On a flat surface insert a carbon flat wing spar in each wing panel. Glue it in with thin CA and accelerator. Step 25 On a flat surface join the two top wing halves together using medium CA. There is no dihedral in the top wing. Do the same for the bottom wing

13 Step 26 Glue in the flat carbon wing center reinforcement with thin CA and accelerator on the bottom wing. Step 27 On the top wing cut a slit in the foam as shown to accept the top wing center reinforcement. Step 28 Glue it in place using thin CA and accelerator.

14 Step 29 Glue two pointed rods in each wing strut with thin CA and accelerator. Step 30 Dry fit the wing strut to the bottom wing. Push the wires into the foam. The position of the strut should be on the line. The front edge of the strut should be 23mm back from the front edge of the bottom wing. Step 31 Hot melt glue the struts to the bottom of the wing.

15 Step 32 Make holes in the top of the fuse for the cabane struts as shown in the photo. Step 33 Make 4 carbon rods that are 5cm long. Wrap them with clear duct tape. Step 34 Insert the two cabane struts in the holes of fuse previously made. Turn the fuse over and put a few drops of CA on the tape/ carbon strut assembly.

16 Step 35 On the bottom of the top wing make two pockets 6cm square for the cabane struts. The center for each hole is 35mm and 95mm form the front of the wing. Do not make a hole through the wing. Step 36 Glue the bottom wing to the fuse with hot melt glue.

17 Glue the leading and trailing edge of the bottom wing. Step 37 Glue the carbon flat spar reinforcement into the elevator with thin CA and accelerator. Step 38 Slide the elevator into the slot in the fuse.

18 Step 39 Set the horizontal stab so that it is the same distance side to side. Step 40 Turn the plane over and insert the wing strut into the top wing as shown. Line the back of the strut up with the leading edge of the aileron and the two wires on the line that is marked on the wing. When this is done hot melt glue the struts to the top wing. Step 41 Pull the two cabane struts into the pockets in the top wing.

19 Step 42 Hot melt glue the two struts into the top wing. Once the glue has set turn the airplane over and pull the top wing so that it is flat. When it is flat glue the cabane struts to the fuse using medium CA and accelerator. Be careful not to put positive or negative incidence in the top wing. Step 43 Glue a carbon rod to the tail wheel wire.

20 Step 44 Glue the assembly into the rudder using thin CA and accelerator. Step 45 Glue the rudder and horizontal stab to the airplane using medium CA and accelerator. Make sure that the tail surfaces are equal distance from the main wing. See photos below. Make sure that the tail surfaces are square and equal distance from the front wing.

21 Step 46 Slip the wheels into place. Hold them in place with heat shrink tubing. Put a drop of thin CA on the tubing to hold it in place. Step 47 Build a left and right wheel pant from the three pieces in the kit. Use medium CA and accelerator to hold the pieces together.

22 The completed wheel Pant Step 48 Put the wheel pant over the wheel. Use hot melt glue to hold the wheel pant in place.

23 Step 49 From the parts grab the two triangle shape landing gear reinforcements. Position them on the landing gear wire as shown. Using medium CA glue the foam triangle pieces in place. Use ht melt glue where the piece mates to the fuse.

24 Step 50 Glue the tail wheel reinforcement on to the plane with hot melt glue. Secure the tail wheel with heat shrink tubing and CA. Step 51 Glue in the servo block as shown using hot melt glue.

25 Step 52 Make a push rod cut out in the rear of the fuse as shown for the rudder. On the opposite side make a cut out as shown for the elevator.

26 Step 53 Make a slit in the foam with a hobby knife for the rudder control horn. Make a slit in the elevator as shown for the elevator control horn. Step 55 Install the elevator and rudder servo using hot melt glue.

27 Step 56 Make up two carbon pushrods as shown using the z bend and heat shrink tubing. Wick a few drops of thin CA into the joint and spray accelerator to set the glue. Step 57 Slip the rudder control horn over the z bend wire. Put the control rod through the fuse as shown. Step 58 Hook up the control rods as shown. Now with thin CA glue in the control horn for the rudder. Follow the same procedure for the elevator.

28 Step 59 Glue in the rear turtle deck cockpit using medium CA. Step 60 On the bottom wing custom fit the servo holes to fit your servos. Step 61 Install the two aileron servos with hot melt glue. Make a slit in each aileron for the control horn. Install the control horn as shown. Glue it in with thin CA.

29 Step 62 On the top wing make a slit in each aileron for the control horn. Glue it in with thin CA. Step 63 On the center of the bottom wing make a hole for the servo leads to go through. Push the servo wires into the slot on the bottom wing.

30 Step 64 Hook up the ailerons as shown. Step 65 Assemble the push rods between the ailerons as shown using carbon rods, Z bends and heat shrink tubing. Put a bend in the wire as shown. This will allow you to make adjustments between the top and bottom ailerons.

31 Step 66 Using hot melt glue attach the cowl mounting blocks to the front firewall. Step 67 Glue the wood motor mount to the front of the airplane as shown. Step 68 Mount the motor to the airplane with four wood screws. Put a couple of washers behind the motor to give it some right thrust. Hook up the wires for the speed controller.

32 Step 69 Attach the cowl, prop and spinner. Step 70 Install the receiver and make all of the servo connections. Step 71 The Center of gravity is 3.5 inches back from the leading edge of the top wing.

33 Step 72 Your Pitts should be ready to fly. For the initial flight set the control throws to the following. You can always add more throw after you get comfortable with the plane. Ailerons- 5/8 inch up and down Elevator- ½ inch up and down. Rudder- 1 ½ inch left and right

INCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT:

INCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT: Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in

More information

(Build Instructions)

(Build Instructions) (Build Instructions) Specifications * Wingspan: 58cm * Length: 50cm * Flying Weight: 59 grams * Channels: 3 (Rudder Elevator Throttle) * Suggested Receiver: 4Ch Micro * Motor: 8mm GearDrive * Prop: GWS

More information

Thank you for your purchase of the Lee Ulinger, FoamtanaS, Yak-55, or Extra 330 3D Depron foam, Aerobatic airplane.

Thank you for your purchase of the Lee Ulinger, FoamtanaS, Yak-55, or Extra 330 3D Depron foam, Aerobatic airplane. Thank you for your purchase of the Lee Ulinger, FoamtanaS, Yak-55, or Extra 330 3D Depron foam, Aerobatic airplane. Tools you will need to build Recommended additional items: #11 hobby knife Motor: Hacker

More information

Taylorcraft Indoor / Cul-De-Sac Flyer

Taylorcraft Indoor / Cul-De-Sac Flyer Taylorcraft Indoor / Cul-De-Sac Flyer Taylocraft Specifications Wingspan: 28.0 in. Wing Area: 117 sq. in. Weight (Ready to Fly): 3.0 3.1 oz. Wing Loading: 3.7 3.8 oz. / sq. ft. LIABILITY RELEASE In that

More information

Citabria Pro. Aerobatic Parkflyer. by Joel Dirnberger

Citabria Pro. Aerobatic Parkflyer. by Joel Dirnberger Citabria Pro Aerobatic Parkflyer by Joel Dirnberger Revision C: December 21, 2004 Citabria Pro Building Instructions Length: Wingspan: Wing Area: Flying Weight: Wing Loading: Functions: Specifications:

More information

EPP Rebel Z 35. White Red w/ Blue Orange w/ Blue Orange w/burgundy Other. Specs. Color - Bottom White Black Checkers Silver Checkers Other Checkers

EPP Rebel Z 35. White Red w/ Blue Orange w/ Blue Orange w/burgundy Other. Specs. Color - Bottom White Black Checkers Silver Checkers Other Checkers EPP Rebel Z 35 Specs AUW ~10.0oz Width 35.28 Length 34.67 Wing Area 1.44 sqft Horz Area 2.35 sqft Vert Area.91 sqft

More information

FUSELAGE CONSTRUCTION

FUSELAGE CONSTRUCTION FUSELAGE CONSTRUCTION Note: prior to building and gluing on the work surface use protective covering on your building surface. (wax paper or clear wrap) Fit the laser cut Fuselage Front and Fuselage Rear

More information

ULS Cherokee. Ultra Low Speed aircraft for indoor RC flying. Zippkits. Specifications: Required to complete:

ULS Cherokee. Ultra Low Speed aircraft for indoor RC flying. Zippkits. Specifications: Required to complete: Zippkits ULS Cherokee Ultra Low Speed aircraft for indoor RC flying. Specifications: Span- 28 inches Wing Area- 151 Sq/In Wing Loading- 3.0 ounces/ft Weight- 3.5 ounces RTF Build time- 1-2 Hours Radio-

More information

C-180 Builder s Manual

C-180 Builder s Manual C-180 Builder s Manual. May 20, 2002 Last revised July 11, 2002 Copyright! 2002 Douglas Binder, Mountain Models www.mountainmodels.com sales@mountainmodels.com (719) 630-3186 1 Required Equipment! Xacto

More information

Revolution 3D-mini ARF

Revolution 3D-mini ARF Revolution 3D-mini ARF 1 Included Hardware 4 Dubro Micro Control Horns #DUB848 2.32 x 18" Linkage Wire (Music Wire) 1 1.5 x 1.25 x 1/8 Balsa Ply (for motor mount) 1 5" piece of Velcro (Optional recommended,

More information

ParkJet Builder s Manual

ParkJet Builder s Manual ParkJet Builder s Manual Thank you for purchasing the ParkJet. The ParkJet is a profile ducted fan airplane that can be flown in a larger park. The ParkJet was initially designed by Scott Stoops and modified

More information

NASTY Build Guide. Supplies needed

NASTY Build Guide. Supplies needed NASTY Build Guide Supplies needed Blucore or Depron Foam. Blucore (Fan Fold Foam) is available at Lowes. Approximately $25 for 50 feet of Blucore. Depron can be ordered on the internet for slightly more.

More information

INCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT:

INCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT: Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in

More information

Magpie. Foam Trainer. Magpie Specifications

Magpie. Foam Trainer. Magpie Specifications Magpie Foam Trainer Magpie Specifications Length: 34in. Wingspan (SF): 46in. Wing Area (SF): 414in 2 Wingspan (SP): 40in. Wing Area (SP): 360in 2 Weight (without battery): 12oz. Thank you for purchasing

More information

35 Magnum. Instruction Manual

35 Magnum. Instruction Manual EPP EPP 35 35 Magnum Rebel Z Instruction Manual This is how your kit will arrive When cutting the hardware package open use caution. The contents are semi-coiled to fit in the box. They will spring open

More information

I hope you enjoy the Spirit as much as I have. Scott DeTray Model Aero

I hope you enjoy the Spirit as much as I have. Scott DeTray Model Aero We are excited to introduce the Model Aero Spirit. Inspired by the magnificent Northrop Grumman B-2 Spirit Stealth Bomber, the Spirit is a great flyer, on land or water. It tracks like an arrow and is

More information

Sbach 1,2m 3D/aerobatic EPP model Building instructions

Sbach 1,2m 3D/aerobatic EPP model Building instructions Sbach 1,2m 3D/aerobatic EPP model Building instructions Please refer to the Diagram sheet Diagrams A, B Press 2 carbon strips (1x3x1000 mm) into the grooves in the sides of the fuselage central part (the

More information

PITTS S2S CONSTRUCTION

PITTS S2S CONSTRUCTION PITTS S2S CONSTRUCTION FUSELAGE CONSTRUCTION 1) Place the right fuselage side over the plan and mark the former positions. Place the left side over the right side and mark the former positions. Glue F1

More information

White Red w/ Blue Orange w/ Blue Burgundy w/ Orange Other

White Red w/ Blue Orange w/ Blue Burgundy w/ Orange Other Specs AUW ~6.5oz Width 32.875 Length 29.50 Wing Area 1.35 sqft Horz Area 2.22 sqft Vert Area 1.26 sqft Suggested Hardware ~25g 90 watt Motor 12 amp ESC Servos 6g+ (4) 2s LiPo (300-500mAh) 4ch Radio/Rx

More information

Hobby Lobby Zip Supplementary instructions Please refer to the included drawings while using these assembly instructions

Hobby Lobby Zip Supplementary instructions Please refer to the included drawings while using these assembly instructions Materials needed: 15 or 30 minute epoxy Medium CA Masking tape Scotch tape Servo Tape Wax paper Tools Needed: Pencil or marker Flat building surface Hobby knife or razor blade 7/64" or 3mm drill bit 3/16"

More information

INS TRUC T I ON M A NU A L

INS TRUC T I ON M A NU A L INS TRUC T I ON M A NU A L Packing list: 1: PP F6F fuselage *1 2: Carbon tube 5*5*940mm *1 3: Pull rod *4 4: Motor mount *1 5: Quick rod adjuster *4 6: Hinge *4 7: M3 screws *4 8: Hook and loop tape *1

More information

RYAN STA SAFETY PRECAUTIONS. "Sport Scale E-Power ARF" For Intermediate and Advanced Fliers. This radio control model is not a toy!

RYAN STA SAFETY PRECAUTIONS. Sport Scale E-Power ARF For Intermediate and Advanced Fliers. This radio control model is not a toy! RYAN STA "Sport Scale E-Power ARF" For Intermediate and Advanced Fliers. SAFETY PRECAUTIONS This radio control model is not a toy! First-time builders should seek advice from people with model building

More information

VT-ALLROUNDER V4 1500MM CORO 3/4 Channel Trainer Airplane

VT-ALLROUNDER V4 1500MM CORO 3/4 Channel Trainer Airplane Congratulations on your purchase of the VT- AllRounder 1500MM Trainer Airplane Kit.. Hope these build instructions help you complete the build. Though the build itself doesn't take much time, just be sure

More information

1/6 PA-25 PAWNEE. *Specifications are subject to change without notice.*

1/6 PA-25 PAWNEE. *Specifications are subject to change without notice.* 1/6 PA-25 PAWNEE INSTRUCTION MANUAL [ A335 Kit ] Wing Span : 72 in / 1830 mm Wing Area : 736 sq in / 47.5 sq dm Flying Weight : 6.6 lbs / 3000 g Fuselage Length : 48 in / 1220 mm Requires : "Glow Power"

More information

Millennium RC presents The New and Improved (now even easier to build and cover!) SSX X-Trainer Build Kit

Millennium RC presents The New and Improved (now even easier to build and cover!) SSX X-Trainer Build Kit Millennium RC presents The New and Improved (now even easier to build and cover!) SSX X-Trainer Build Kit Wing span: Approx. 42 Wing Area: 504 sq. in. Wing Loading: 6.71 oz/ sq. ft. Introduction: The Slow

More information

Model Aero Aqua Cat, Aqua Cat SE, and Aqua Jet Build Guide

Model Aero Aqua Cat, Aqua Cat SE, and Aqua Jet Build Guide Model Aero Polaris Model Aero Aqua Cat, Aqua Cat SE, and Aqua Jet Build Guide Note: Aqua Cat SE and Aqua Jet specific instructions are at the end of the build guide. Some photos may depict the Polaris

More information

Dandy Sport Builder s Manual

Dandy Sport Builder s Manual Dandy Sport Builder s Manual Thank you for purchasing the Dandy Sport. The Dandy Sport has been designed as an easy to build aileron trainer. Take your time and enjoy building this plane. Specifications:

More information

CARL GOLDBERG PRODUCTS, LTD.

CARL GOLDBERG PRODUCTS, LTD. Chipmunk 400 WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that could be dangerous.

More information

Corvus Racer Colour schemes. AeroPlus RC Copyright 2013 All Rights Reserved

Corvus Racer Colour schemes. AeroPlus RC Copyright 2013 All Rights Reserved Corvus Racer 540 59 Item No:A E050003 Specifications WING SPAN: 59"(1500mm) LENGTH: 54.1"(1374mm) WING AREA: 654sq.in.(42.2sq.dm.) FLYING WEIGHT: 4.6 5.3lbs(2000 2300g) Electric:Brushless outrunner 8Oz.

More information

Magpie AP. Aerial Photography Airplane

Magpie AP. Aerial Photography Airplane Magpie AP Aerial Photography Airplane Magpie Specifications Length: 36in. Wingspan: 54in. Wing Area: 486in 2 Weight (without battery): 19 oz. Thank you for purchasing the Magpie AP. This model is an elevator/rudder

More information

MOUNTAIN MODELS P-51 Mustang. 1/12 Scale Electric Park Flyer. Copyright Mountain Models

MOUNTAIN MODELS   P-51 Mustang. 1/12 Scale Electric Park Flyer. Copyright Mountain Models 1 MOUNTAIN MODELS www.mountainmodels.com P-51 Mustang 1/12 Scale Electric Park Flyer Wingspan: 37, Wing Area: 254 sq. in., Weight: 15 to 19.5 oz Instructions Version 1.4, May 23, 2007 Kit Contents: 2 1.

More information

Cover the wing trailing edge and the aileron leading edge with strapping tape as shown.

Cover the wing trailing edge and the aileron leading edge with strapping tape as shown. Cover the wing trailing edge and the aileron leading edge with strapping tape as shown. The aileron hinges are done using strapping tape on the top and bottom surfaces of the ailerons as shown. Make sure

More information

Designed by Steve Shumate Adapted from the North Star design by Laddie Mikulasko

Designed by Steve Shumate Adapted from the North Star design by Laddie Mikulasko Model Aero Polaris Specifications: Designed by Steve Shumate Adapted from the North Star design by Laddie Mikulasko Wing area: 343 sq in Span: 29.0" Length: 38.4" Weight RTF: 18 to 22 oz (prototype weighed

More information

Switchback Sport Builder s Manual

Switchback Sport Builder s Manual Switchback Sport Builder s Manual Thank you for purchasing the Switchback Sport. The Switchback Sport has been designed for the novice to intermediate pilot who wants a plane with good performance that

More information

Corvus Racer CC

Corvus Racer CC Corvus Racer 540 35CC Item No:L-G035008 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio mm mm 1200sq in (77.4sqdm) 9.9-12lbs(4.5-5.5kg) 91-1.20(2C) 1.10-1.40(4C) 20-40cc

More information

uin RC FPRC ZERO Specificationss Empty Weight

uin RC FPRC ZERO Specificationss Empty Weight Flying Pengu uin RC FPRC ZERO Specificationss Wing Span 42.75 (1085 mm) Fuselage length 30.5 ( 775 mm) Empty Weight 9.5 10 oz. (150 160g) Estimated Flying Weight 20 255 oz. (320 400g) Wing Area: 151 sq.

More information

Warbird Series Zero - 32 Assembly Manual

Warbird Series Zero - 32 Assembly Manual Warbird Series Zero - 32 Assembly Manual Specifications Wing Span: 32 inches Wing Area: 210 in 2 Fuselage Length: 26 inches Weight (ready to fly): 11 to 13 oz. Wing Loading: 7.5 to 8.9 oz/ft 2 Designed

More information

43in EPP Acrocub Instruction Manual

43in EPP Acrocub Instruction Manual 43in EPP Acrocub Instruction Manual Specifications Wingspan: 43.3in (1100mm) Length: 41.3in (1050mm) Flying Weight: Approx. 1.5lb (670g) Dear Customer, Congratulations on your purchase of 43in EPP Acrocub

More information

Zlín Z-37A Čmelák ("Bumblebee ) 850 mm. Assembly Instructions and recommended equipment of the RC model

Zlín Z-37A Čmelák (Bumblebee ) 850 mm. Assembly Instructions and recommended equipment of the RC model Zlín Z-37A Čmelák ("Bumblebee ) 850 mm Assembly Instructions and recommended equipment of the RC model 1 Technical information: Wingspan: Overall Length: Flying weight: RC Functions: 850 mm 610 mm ~380

More information

30% Edge 540T Almost Ready to Fly

30% Edge 540T Almost Ready to Fly Lanier R/C 30% Edge 540T Almost Ready to Fly WARNING! THIS IS NOT A TOY! THIS IS NOT A BEGINNERS AIRPLANE This R/C kit and the model you will build from it is not a toy! It is capable of serious bodily

More information

LANIER - Double Trouble - INSTRUCTIONS. Tail 1 T1 ¼ Balsa 1 T2 ¼ Balsa 2 T3 ¼ Balsa 1 T4 ¼ Balsa 1 T5 ¼ Balsa 1 T6 ¼ Balsa 2 J1 ¼ Balsa 2 J2 Lite ply

LANIER - Double Trouble - INSTRUCTIONS. Tail 1 T1 ¼ Balsa 1 T2 ¼ Balsa 2 T3 ¼ Balsa 1 T4 ¼ Balsa 1 T5 ¼ Balsa 1 T6 ¼ Balsa 2 J1 ¼ Balsa 2 J2 Lite ply Tail 1 T1 ¼ Balsa 1 T2 ¼ Balsa 2 T3 ¼ Balsa 1 T4 ¼ Balsa 1 T5 ¼ Balsa 1 T6 ¼ Balsa 2 J1 ¼ Balsa 2 J2 Lite ply Other Parts 2 Aluminum Gear 1 3/32 Music wire tail skid 2 Elevator and J-plane joiner wire

More information

SwitchBack Senior. SwitchBack Senior Specifications

SwitchBack Senior. SwitchBack Senior Specifications SwitchBack Senior SwitchBack Senior Specifications Wingspan: 55.4 in. Length: 41 in. Wing Area: 597 sq. in. Weight (Ready to Fly): 34 to 37 oz. Wing Loading: 8.2 to 8.9 oz. / sq. ft. Version 1.05, March

More information

Build and fly this exact scale 43-in. control-line version of the popular Cessna private plane.

Build and fly this exact scale 43-in. control-line version of the popular Cessna private plane. Seeing double? Clever photography gives that illusion but actually it s only the model 140 in the foreground. Author Stahl (right) does fly both the job he is holding and his real Cessna 14 pictured in

More information

SGTalon s Enterprise-A Foamie Build Guide. SGTalon s. Enterprise. Enterprise--A. Assembly Instructions

SGTalon s Enterprise-A Foamie Build Guide. SGTalon s. Enterprise. Enterprise--A. Assembly Instructions SGTalon s Enterprise SGTalon s Enterprise--A Enterprise Assembly Instructions Page 1 4-13-2013 SGTalon s Enterprise *******Recommended Hardware******** 2.6oz 250w Motor and Speed Control with 8x6 prop

More information

MECOA EZ-4061 Trainer

MECOA EZ-4061 Trainer MECOA EZ-4061 Trainer EZ-4061 is a newly designed, Almost Ready to Fly kit. It is an extremely easy to control trainer with strong construction and excellent aerodynamic performance. This is a great choice

More information

Combat Foamie. An electric powered model made from sheet foam for full contact combat matches. Designed by. Plan by Paul Bradley. Jerry W.

Combat Foamie. An electric powered model made from sheet foam for full contact combat matches. Designed by. Plan by Paul Bradley. Jerry W. Combat Foamie An electric powered model made from sheet foam for full contact combat matches Designed by Jerry W. Hagood Plan by Paul Bradley July 2010 Combat Foamie Top View 22.9 CG is 7.3 back from nose

More information

The BIPE NX Assembly Manual

The BIPE NX Assembly Manual The BIPE NX Assembly Manual Specifications Wing Span: 34 inches Wing Area: 550 in 2 Fuselage Length: 36 inches Weight (ready to fly): 20 to 24 oz. Wing Loading: 5.2 to 6.3 oz/ft 2 Designed by Jim Vigani

More information

S.E.5a (Build Instructions)

S.E.5a (Build Instructions) S.E.5a (Build Instructions) Specifications Wingspan: 38 cm Length: 31cm Flying Weight: 41 Channels: 3 (Rudder Elevator Throttle) Suggested Receiver: 3Ch Brick Motor: 7mm Geared Motor Airframe Only Kit

More information

EXTRA 330SC 60CC. Item No:H G Specifications cc gas DA50,DA60, DLE55, DLE60(twin), 3W55. Description

EXTRA 330SC 60CC. Item No:H G Specifications cc gas DA50,DA60, DLE55, DLE60(twin), 3W55. Description EXTRA 330SC 60CC Item No:H G060011 Specifications Wing Span Length Wing Area Flying Weight Gasoline Radio Description Carbon Fibre : 92" (2347mm) 84 1/2 " (2060mm) 1526.8 sq in(98.5sq dm) 16 17lbs(7300

More information

LoLo. A sporty parkflyer with an Old Timer flair! Designed by: Tres Wright Kitted by: Park Scale Models

LoLo. A sporty parkflyer with an Old Timer flair! Designed by: Tres Wright Kitted by: Park Scale Models LoLo A sporty parkflyer with an Old Timer flair! Designed by: Tres Wright Kitted by: Park Scale Models http://www.parkscalemodels.com/ Assembly Instructions General Information The laser cutting process

More information

Edge 540 V3 35CC. Scheme A. Item No:L G Specifications. Flying Weight

Edge 540 V3 35CC.  Scheme A. Item No:L G Specifications. Flying Weight Edge 540 V3 35CC Item No:L G035016 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio Description 76 (1930mm) 74 (1879mm) 1200sq in(77.4sqdm) 9.9 12lbs(4.5 5.5kg) 91 1.20(2C)

More information

Instruction Manual. Specification:

Instruction Manual. Specification: Instruction Manual H I G Specification: Wingspan: 133 cm (52.3 inches) Length : 104 cm (40.9 inches) Weight : 1830gr Engine : 25-32 two stroke Radio : 4 channel - 4 servo H W I N G KIT CONTENTS: We have

More information

AVRO R/C Scale Model Instructions CONTACT INFORMATION. Designed by Peter Rake Modified by M.K. Bengtson

AVRO R/C Scale Model Instructions CONTACT INFORMATION. Designed by Peter Rake Modified by M.K. Bengtson R/C Scale Model Instructions CONTACT INFORMATION Designed by Peter Rake Modified by M.K. Bengtson Manufactured and Distributed by: Bengtson Company e-mail: sales@aerodromerc.com Web Site: www.aerodromerc.com

More information

Eva. Extremely Versatile Airframe

Eva. Extremely Versatile Airframe Eva Extremely Versatile Airframe Eva Specifications Length: 32 Weight (without battery): ~12oz. Revision History Date Revision Notes/Comments 6/3/05 Document initial creation. Thank you for purchasing

More information

CARL GOLDBERG PRODUCTS, LTD.

CARL GOLDBERG PRODUCTS, LTD. Eagle 400 WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that could be dangerous.

More information

34" PELICAN by CRASH TEST HOBBY

34 PELICAN by CRASH TEST HOBBY 34" PELICAN by CRASH TEST HOBBY The Pelican is a 34" trainer that can level its own wings and put its nose on the horizon once trimmed and balanced. It can handle more wind than most EZ flying planes in

More information

F-16 Falcon 70mm EDF

F-16 Falcon 70mm EDF F-16 Falcon 70mm EDF Instruction manual Specifications: Winspan: 640 mm Length: 990 mm Weight: 900-1100 gram Ducted fans 70mm x 1 Required tools and components:. 4 ch. Computer Radio system w/ 2 servos.

More information

INCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT:

INCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT: Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in

More information

2COOL 2COOL.indd :24:34

2COOL 2COOL.indd :24:34 2COOL 2COOL.indd 1 17.9.2004 12:24:34 2COOL Dear customer, congratulations on the purchase of the 2Cool model. Before you begin, please read carefully the building instructions and make sure that you understand

More information

LANDING GEAR. 1. Fit landing gear into slots on bottom of fuselage.

LANDING GEAR. 1. Fit landing gear into slots on bottom of fuselage. LANDING GEAR 1. Fit landing gear into slots on bottom of fuselage. 4. Use channel-lock pliers to press blind nuts into position (note: drilled hole should be slightly smaller than shaft of blind nut for

More information

105" TIGER MOTH ARF INSTRUCTION MANUAL VERSION 1.0

105 TIGER MOTH ARF INSTRUCTION MANUAL VERSION 1.0 105" TIGER MOTH ARF INSTRUCTION MANUAL VERSION 1.0 Step 1. Installation of the aileron servos 1) Mount aileron servo to servo mounting blocks with servo s screws. Install servo mounting plate with screws.

More information

ALBATROSS by CRASHTESTHOBBY.COM

ALBATROSS by CRASHTESTHOBBY.COM ALBATROSS by CRASHTESTHOBBY.COM The Albatross is a unique slow flyer designed to put its nose on the horizon and level its own wings without a pilot. It is very quiet and designed to use inexpensive electronics.

More information

28in Super EVA Foam. F-22 Raptor Kit. Specifications. Wingspan: 27.5in (700mm) Length: 38.3in (975mm) Flying Weight: Approx. 1.

28in Super EVA Foam. F-22 Raptor Kit. Specifications. Wingspan: 27.5in (700mm) Length: 38.3in (975mm) Flying Weight: Approx. 1. 28in Super EVA Foam F-22 Raptor Kit Specifications Wingspan: 27.5in (700mm) Length: 38.3in (975mm) Flying Weight: Approx. 1.2lbs (530g) Dear Customer, Congratulations on your purchase of 28in F22 Raptor

More information

Super Sky Surfer 2000 Assembly Instructions

Super Sky Surfer 2000 Assembly Instructions Super Sky Surfer 2000 Assembly Instructions Note: Plug and Play version of the Sky Surfer comes with fuselage pre-glued and motor/servos installed. If you wish to route antennas or wires through the tail,

More information

EPP EAGLE THE RC RAPTOR

EPP EAGLE THE RC RAPTOR EPP EAGLE THE RC RAPTOR Installation Manual FLYEAGLE2007@GMAIL.COM TM Step 1: Verify that all the EPP Eagle pieces are included in the Kit. Before we start. Step 2: Identify the pieces need to assemble

More information

Venturi EVO 2 FPV. Thank you for purchasing the Venturi EVO FPV wing

Venturi EVO 2 FPV. Thank you for purchasing the Venturi EVO FPV wing Thank you for purchasing the Venturi EVO FPV wing The Venturi FPV is designed for First Person Viewing (FPV) and for UAV/Drone experimentation. There is a power system for this model, see the website for

More information

Parkflyer F6F Hellcat

Parkflyer F6F Hellcat Parkflyer F6F Hellcat Page 1 of 19 MOLT MODELS Background Design Philosophy When I was first introduced to this hobby seventeen years ago I saw my first WWII warbird and I was hooked. Several years later

More information

MercurE Mini Old Timer Electric Model

MercurE Mini Old Timer Electric Model MercurE Mini Old Timer Electric Model MercurE Specifications Wingspan: 31.6 in. Length: 20.6 in. Wing Area: 153 sq. in. Weight (Ready to Fly): 4.9 to 5.4 oz. Wing Loading: 4.6 5.1 oz. / sq. ft. Version

More information

Ÿ Battery Strap Ÿ Paper Knife Ÿ Elevon Throw Gauge Ÿ Instructional Manual. Building Tools:

Ÿ Battery Strap Ÿ Paper Knife Ÿ Elevon Throw Gauge Ÿ Instructional Manual. Building Tools: Congratulations on your purchase of the TuffBirds Spec Racer Flying Wing. We Hope these build instructions will help you complete the build easily. Though the build itself doesn't take much time, just

More information

High performance 90mm fiberglass jet

High performance 90mm fiberglass jet High performance 90mm fiberglass jet Assembly manual For intermediate and advanced fliers only! Specs Wingspan: 1255mm Fuselage length: 1250mm Flying weight: 2600-3000g Wing area: 22.6 dm² Wing loading:

More information

3D Fun Flyer Build Guide 30 Span

3D Fun Flyer Build Guide 30 Span 3D Fun Flyer Build Guide 30 Span Designed by Me_Wantee RC Groups Thread http://www.rcgroups.com/forums/showthread.php?t=659911&pp=25 My Setup Motor Axi 2212/34 Prop 10 x 4.7 Speedie 18A Servos are eflight

More information

MiniacRC MIGHTY MINI P40 WARHAWK

MiniacRC MIGHTY MINI P40 WARHAWK Hand-Cutting and Skins) MiniacRC MIGHTY MINI P40 WARHAWK FliteTest style RC model Build Instructions Make sure that the orientation for molded pieces such as the scoop rings and landing gear housings are

More information

HIGH-END TECHNOLOGY. Electric ducted fan Starfighter

HIGH-END TECHNOLOGY. Electric ducted fan Starfighter HIGH-END TECHNOLOGY RC Electric ducted fan Starfighter First we want to thank and congratulate you with your decision in buying one of our Kits. The Starfighter puts together very easily so there is not

More information

F3A -70E ASSEMBLY MANUAL

F3A -70E ASSEMBLY MANUAL F3A -70E ASSEMBLY MANUAL The new F3A-70E, was designed in an extremely lightweight structure, the all wood airframe, and the new revolutionary Lift Generator on landing gear give the F3A-70E an impressive

More information

Construction Guide for Quick Build MIG-29 Design by Tomas Hellberg

Construction Guide for Quick Build MIG-29 Design by Tomas Hellberg Construction Guide for Quick Build MIG-29 Design by Tomas Hellberg This kit is very simple to put together. The biggest danger in messing up this kit is gluing the pieces to your work bench. But before

More information

Ryan STA Sport Scale Model Aircraft Assembly and Instruction Manual

Ryan STA Sport Scale Model Aircraft Assembly and Instruction Manual Ryan STA Sport Scale Model Aircraft Assembly and Instruction Manual Warning: This radio controlled model is not a toy. It requires skill to fly and is not recommended for the novice pilot. It should not

More information

Zlín Z-37A Čmelák ("Bumblebee ) mm. Assembly Instructions and recommended equipment of the RC model

Zlín Z-37A Čmelák (Bumblebee ) mm. Assembly Instructions and recommended equipment of the RC model Zlín Z-37A Čmelák ("Bumblebee ) - 1 530mm Assembly Instructions and recommended equipment of the RC model Technical information: Wingspan: 1530 mm Overall Length: 920 mm Flying weight: ~1 700g RC Functions:

More information

INCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT:

INCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT: Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in

More information

Cheeper Assembly instruction

Cheeper Assembly instruction 1. Equipment, materials and tools for assembly.......2 2. Assembly.....3 3. Setting of the model.....11 1. Equipment, materials and tools for assembly 1 Wing; 2 Fuselage; 3 Stabilizer; 4 Fin; 5 Dowel for

More information

Hercules Twin Puller 66" and 78" Building Instructions

Hercules Twin Puller 66 and 78 Building Instructions Hercules Twin Puller 66" and 78" Building Instructions The EPP Hercules Twin Pullers are some of the toughest BIG FPV planes on the planet. They are unique because they can take off the ground without

More information

Parts Identification

Parts Identification We are excited to introduce the Model Aero Aqua Sport. This is an excellent sport flyer, equally at home flying from grass fields, water, or even snow! The unique V-tail gives the Aqua Sport a distinctive

More information

T-15 EDF INSTRUCTION MANUAL. Wingspan.31in. Weight..2.5 lb. EDF...70mm 12 Blade ToughJets, LLC Kittery, ME Page 1 of 22.

T-15 EDF INSTRUCTION MANUAL. Wingspan.31in. Weight..2.5 lb. EDF...70mm 12 Blade ToughJets, LLC Kittery, ME Page 1 of 22. TM T-15 EDF INSTRUCTION MANUAL Specifications Wingspan.31in Length..41.75in Wing Area 515 sq in EDF...70mm 12 Blade Weight..2.5 lb Radio...3 channel Motor...Brushless Battery 14.8v 2200mah 40c 2013 ToughJets,

More information

Specifications Wingspan: 43cm Flying Weight: 33 grams (with battery) Channels: 3 Suggested Receiver: 4Ch Micro Motor: 7mm Brushed Geardrive

Specifications Wingspan: 43cm Flying Weight: 33 grams (with battery) Channels: 3 Suggested Receiver: 4Ch Micro Motor: 7mm Brushed Geardrive Specifications Wingspan: 43cm Flying Weight: 33 grams (with battery) Channels: 3 Suggested Receiver: 4Ch Micro Motor: 7mm Brushed Geardrive Airframe Kit (Included Contents) * Airframe Parts Sheets (Depron)

More information

TIGER MOTH 120 ASSEMBLY INSTRUCTIONS

TIGER MOTH 120 ASSEMBLY INSTRUCTIONS TIGER MOTH 120 ASSEMBLY INSTRUCTIONS SPECIFICATIONS Wing Span: Length: Radio: Flying Weight: 1920mm 1580mm 4 channel with 6 servos 4200g AILERON ASSEMBLY 1 Start by removing the servo cover from the bottom

More information

Precut Wingola Kit Instructions

Precut Wingola Kit Instructions Precut Wingola Kit Instructions Below is the precut option. Battery compartment, Receiver and Servo Trays are cut for mini radio gear. This is the uncut version. It has the placement laid out for the radio,

More information

Assembly Manual / Airframe 65 Vyper SAFETY in Assembly SAFETY in Flying

Assembly Manual / Airframe 65 Vyper SAFETY in Assembly SAFETY in Flying 1 Assembly Manual / Airframe 65 Vyper Thank you for purchasing this 3DHobbyShop ARF RC aircraft. If you have any issues, questions, concerns or problems during assembly, please contact our tech department

More information

Construction Guide for Quick Build F-22 Raptor Design by Tomas Hellberg

Construction Guide for Quick Build F-22 Raptor Design by Tomas Hellberg Construction Guide for Quick Build F-22 Raptor Design by Tomas Hellberg This kit is very simple to put together. The biggest danger in messing up this kit is gluing the pieces to your work bench. But before

More information

Instruction Manual book

Instruction Manual book Instruction Manual book ITEM CODE BH53. SPECIFICATION Wingspan : 1,250mm 49.21 in. Length : 930mm 36.61in. Weight : 1.1kg 2.42 Lbs. Parts listing required (not included). Battery: 3 CELLS-LI-POLY-11.1V-2,500

More information

GRIM REAPER Building Instructions by CRASHTESTHOBBY.COM

GRIM REAPER Building Instructions by CRASHTESTHOBBY.COM GRIM REAPER Building Instructions by CRASHTESTHOBBY.COM The Reaper is one of the toughest planes on the planet. The Grim Reaper is our club's favorite combat plane. It is also used for FPV. It has an amazing

More information

Fibertech N More cc 103 SUPER CHIPMUNK ASSEMBLY MANUAL. pg. 1

Fibertech N More cc 103 SUPER CHIPMUNK ASSEMBLY MANUAL. pg. 1 Fibertech N More 50-60cc 103 SUPER CHIPMUNK ASSEMBLY MANUAL pg. 1 Introduction Thank you for choosing Fibertech N More 103 Super Chipmunk. We have taken great effort into making this kit a great plane

More information

MXS R 30CC. Item No:L G Specifications. 67 1/2"(1720mm) (2C) (4C) 26 35cc gas DLE 30/35RA MLD35 JC30Evo.

MXS R 30CC. Item No:L G Specifications. 67 1/2(1720mm) (2C) (4C) 26 35cc gas DLE 30/35RA MLD35 JC30Evo. MXS R 30CC Item No:L G030008 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio Description Covering Material Carbon Fibre : 75"(1915mm) 67 1/2"(1720mm) 1023sq in(66sq

More information

Pfalz E1 Monoplane 48 EZ Build Version

Pfalz E1 Monoplane 48 EZ Build Version Pfalz E1 Monoplane 48 EZ BUILD Pfalz E1 Monoplane 48 EZ Build Version R/C Scale Model Instructions CONTACT INFORMATION Designed by M.K. Bengtson Prototype by Robert Hoffman Manufactured and Distributed

More information

LANIER - Ultimate Pitts - INSTRUCTIONS. Additional Parts Required. (12) 4-40 blind nuts (Dubro #606)

LANIER - Ultimate Pitts - INSTRUCTIONS. Additional Parts Required. (12) 4-40 blind nuts (Dubro #606) Additional Parts Required (4) or more channel radio with 7-8 servos..91-2.2 two stroke or 1.20-1.84 four stroke engine Appropriate Master Airscrew prop and Hayes mount for your engine. 3 Tru-Turn spinner

More information

RESolution V2 Manual

RESolution V2 Manual RESolution V2 Manual Note for the German Manual: Yellow Bottle thick CA Pink Bottle Med CA Blue tube 5 minute Epoxy Green tube 90 Minute Epoxy Construction of the Fuselage Step 1: Cover the plan with a

More information

6mmFlyRC.com Super Bandit Assembly Instructions

6mmFlyRC.com Super Bandit Assembly Instructions Assembly Instructions Start the assembly with forward fuselage. Lay the two fuselage sides down on a flat surface and glue the foam corner doublers to the locations shown on the plans. Make sure to make

More information

R/C Scale Model Instructions

R/C Scale Model Instructions Vickers 151 Jockey 32.6 Vickers 151 Jockey 32.6 1/12 Scale R/C Scale Model Instructions CONTACT INFORMATION Designed by M.K. Bengtson Prototype by Bert Ayers Manufactured and Distributed by: Bengtson Company

More information

L 410 UVP-E Turbolet. Recommended equipment and guide for the building of RC model aircraft.

L 410 UVP-E Turbolet. Recommended equipment and guide for the building of RC model aircraft. L 410 UVP-E Turbolet Recommended equipment and guide for the building of RC model aircraft. - 1 - History of L-410 It has been 45 years since the first small commercial L-410 prototype took off. The first

More information

Cleveland Quickie Luscombe Silvaire

Cleveland Quickie Luscombe Silvaire Cleveland Quickie Luscombe Silvaire This plan package is not a 100% copy of the original kit. As you make your way through the instructions you will see the differences. Here s just a few of them: The

More information

MiniacRC MIGHTY MINI Ju 87 SIMPLE STUKA

MiniacRC MIGHTY MINI Ju 87 SIMPLE STUKA MiniacRC MIGHTY MINI Ju 87 SIMPLE STUKA FliteTest style RC model Build Instructions General Tips) Confirm that the main posterboard pieces (turtle decks, hatch covers, etc ) are cut out with the proper

More information

Print template tiles and put together with clear tape to complete template.

Print template tiles and put together with clear tape to complete template. Print template tiles and put together with clear tape to complete template. Cut each pattern out with scissors or use a razor and strait edge ruler. Use the ruler as a guide for the razor to get nice strait

More information