Fw-190 D9(50cc) INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
|
|
- Elisabeth Gregory
- 5 years ago
- Views:
Transcription
1 Fw-90 D9(50cc) Specification: Length: 00mm(8.5 ) Wing span: 093mm(8.5 ) Wing area: 77.79sq.dm(8.sq.ft) Wing loading: g/sq.dm(0oz/sq.ft) Flying weight: 9.5kg(0.9 bs) Radio: ch & 8servos Engine: 50cc gasoline engine INSTRUCTION MANUAL SAFETY PRECAUTIONS This R/C airplane is not a toy! (The people under 8 years old is forbidden from flying this model) First-time builders should seek advice from people having building experience.if misused or abused,it can cause serious bodily injury and damage to property. Fly only in open areas and preferably at a dedicated R/C flying site. We suggest having a qualified instructor carefully inspect your airplane before its first flight.please carefully read and follow all instructions included with this airplane,your radio control system and any other components purchased separately.
2 Gasoline 9 channel radio for aiplane is highly recommended for this model. : 50cc gas engine 9 Optional parts: rubber wheel with metal hub, oleo struts and retracts system..8 in Spinner X8-0 We strongly recommend you use the thread lock for all the screws when you build your model.
3 Two wheel retract system Rod (.5x300mm) TP Screw (.3xmm) Make sure to assemble retracts as instructed below. Servo tray(8.5x5.5xmm) Wooden Block(0x0x8mm) Strut 3-way pressure inlet 3-way pressure inlet Strut 3 Pin hinge(xmm) Screw (x0mm) Lock Nut (mm ) 3-way pressure inlet Strut 8 (xmm) 3-way pressure inlet Assemble the aileron to main wing with instant type CA glue. Be careful to ensure the moving parts of the hinges are able to move freely. Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! Apply instant type CA glue to aileron and pin hinge. Pin hinge(xmm) Install the servo as the illustration below 5 Install the nylon control horn and connect the linkage. Air inlet 3-way pressure inlet Quick release connector Pressure reduction inlet Air tank Quick release connector Ø0.mm Make sure hinges are mounted in the same line. Switch Ø.7mm Please insure the sealing of the retract system before flight. Pleas notice the inner diameter for each side of the pressure reduction inlet. Retainer The status when the gear up Air valve Pull out length of 8mm to make gear down Tailing edge TP Screw(.xmm) Air valve Keep some space about mm width between aileron and trailing edge. Rod (X300mm) Strut ( 0 ) Switch Air line (3000mm) 3-way pressure inlet Air tank Air inlet Quick release connector Strut ( 90 ) Screw (3x0mm) Aileron 5 mm Screw (x0mm) Lock Nut (mm ) Rod (.5x300mm) Make sure they are in the right position while installing. (xmm) Screw (3x0mm) Rod (.5x300mm) Screw (x0mm) Lock Nut (mm ) (xmm)
4 8 Secure the servo.install the nylon control horn and connect the linkage. TP Screw (.3xmm) Screw (3x0mm) Lock Nut (mm ) 78 Side View AILERON Flap mm FLAP 9 Wooden Block(0x0x8mm) Pin hinge(xmm) Screw (x35mm) Lock Nut (mm ) (xmm) 7 AILERON Make sure they are in the right position while installing. Screw (x0mm) 0mm 80 FLAP Cut and stick the white stripe stickers to relevant position on the wheel pants,bottom covers to match the model well. 8 Securely glue together. If coming off during flighs, you 'll lose control of your airplane which leads to accidents! 0 Apply instant type CA glue to flap and pin hinges. Pin hinge(xmm) Assemble the flap to main wing with instant type CA glue. Be careful to ensure the moving parts of the hinges are able to move freely. 0mm 55mm (xmm) Servo tray(8.5x5.5xmm) The centre of the Gravity. 30mm mm Rod (.5x300mm) TP Screw (.3xmm) 79 Adjustment. Trailing edge.5mm Rod (.5x300mm) Keep some space about mm width between trailing edge and flap. Install the servo. White sticker for servo tray(x800mm) 5
5 7 75 The sketch map when assemble the tail landing gear to the wheel steeling mount. TP Screw (.3x8mm) Tail wheel (5mm) Tail landing gear Trim the tail wheel cover and assemble it to fuselage with screw. Screw (3x0mm) Collar(3mm) Mount the gear door and the wheel to the retract. Wheel (5mm) Rod (.5x300mm) LockNut(mm) Bushing (8Xmm) Screw (x0mm) Lock Nut (mm ) Tail gear mount Collar(3mm) TP Screw (.3x8mm) Ply (5x5x3mm) 73 3 Install the nylon control horn and connect the linkage..5mm Collar(3mm) 7 Assemble the wheel mount to the thick wooden block with screw,cut the surplus parts and epoxy the thinner wooden block to it as illustration. Screw (3x0mm) Rod (.5x300mm) (xmm) Adjustment. Wooden Block Screw (x0mm) Lock Nut (mm ) (xmm) Retracts strut Note:rubber wheels oleo struts and retracts are optional. Secure the servo.install the nylon control horn and connect the linkage. Cut off the surplus parts from the wheel wells along the shaded line carefully. 5 Trim the covering carefully from the relevant position in the wing for assembling the wheel wells. TP Screw (.3xmm) Side View.5mm Rod (.5x300mm) TP Screw(3x0mm) (3xmm) TP Screw(3x0mm) 7 Screw (3x0mm) RUDDER mm 0mm Lock Nut (mm ) 0mm (3xmm) Top view (xmm) Screw (x35mm) 77 Epoxy the whole wheel mount set to the form in the fuselage and be careful don't let the arm touch the fuselage when it works Adjustment. Top view ELEVATOR 5mm 0mm wheel mount servo 5mm Main wing joiner Screw (x50mm) Blind Nut (mm) Wood dowel (x50mm) Wood dowel (x30mm) Rib template (mm ply) Wooden Block(Not included) Wooden Block(Not included) Wheel (5mm)(Not included) Bushing (8Xmm)(Not included) Side View Centre of Gravity. Position for right diagram. TP Screw (3x0mm)(Not included) Nut (mm)(not included) 3
6 9 Epoxy the wheel wells to the wings. According to the rib template drill holes to another main wing. 7 Glue the exhaust to the fuselage as below. Wheel (5mm) Collar (mm) Wooden Block(3x8xmm) Landing gear(mm) TP Screw (3x0mm ) (3xmm) Landing gear straps Wooden Block(5x5x3mm) Nose arm(3mm) Tail landing gear(3mm) Tail wheel (5mm) mm Rib template (mm ply) TP Screw (.3x8mm) Ply (5x5x3mm) 7 0 Assemble the retract to appropriate position in the wing. Connect the wings with main wing joiner Glue the small fairing parts to appropriate position in the fuselage. 3 Assemble the wheel and gear door to landing gear. Collar (mm) TP Screw (3x0mm) Collar (mm) TP Screw (3x0mm).5mm 00mm Wooden Block TP Screw (.xmm) 8 (3xmm) Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! According to the rib template drill holes in one wing and epoxy wood dowel in them. Wood dowel (x30mm) Rib template (mm ply) Main wing joiner Drill holes at appropriate position in the wing for taking the air line and the servo line out. 9 Wooden supporter 7 Clue the trimed bottom cover to the appropriate position on the wing and drill holes in the rear cover for assembling the wings easier when it needed. 50mm 30mm mm 0mm R0 Rib template (mm ply) Main wing joiner Wood dowel (x30mm) 3 Epoxy the landing gear to the wing steadily.
7 According to the engine cut off the suplus part from the former and glue it to the fuselage.as illustration.. Cut away the surplus parts of canopy and parts carefully along the shade line. 5 Drill holes in the wings and set the wood dowels in them as below. Assemble the wings. Drill.mm holes at the place of main wing. mm A A` Install the wing to the fuselage with x50mm screws as shown in the diagrams below. Wood dowel (x50mm) B Former for fuselage Wood dowel (x50mm) 5 Epoxy the cowl frame into the cowl steadily. Assemble the canopy to the fuselage with TP. 3 B` A=A' B=B' Drill holes to relevant position in the fuselage. 0mm Pin hinge(xmm) Stab joiner (x0mm) 7mm U-style wire 50x5mm Matal douel (x30mm) Rib template (mm ply) 5mm mm Plastical tube(3x30mm) Screw (x0mm) Nut (mm ).5mm Cowling former 3 0mm TP Screw (.3x8mm) Assemble the cowling to fuselage with screw. (x5mm) Epoxy the part to the appropriate position in wing carefully as below. pvc Assemble the wings to the fuselage with screw and blind nut as below. Screw(x50mm) mm 5mm 35mm TP Screw(3x0mm) 0mm Rib template (mm ply) Blind Nut (3xmm) A ccording to thr rib template drill holes to the tail of fuselage as below..mm.8mm Screw(x50mm) Blind Nut (mm) 0mm 5
8 7 30 Set the U-style wire through the enlarged hole as below. Drill holes to appropriate position in the stabilizer and epoxy it to the fuselage as below Assemble the throttle servo in the fuselage. Install the servo of swith. U-style wire 50x5mm x0mm U-style wire 50x5mm Add a rubber ring to the clevis for insuring safety 8 3 The sketch map of the steel wires in the fuselage. Apply instant type CA glue to elevator and pin hinge. Pin hinge(xmm) 57 0 Assembly of the fuel tank. The servos installation finished sketch map. Assemble the receiver and the battery to appropriate in the fuselage. switch servo Throttle servo Rudder servo 3mm Air pressure line Fuel spray line 9 3 Drill two holes at the stabilizer root base on rib template and epoxy the wood dowel in them. Stab joiner (x0mm) Wood dowel (x30mm) Elevator servo Fuel supply line Make sure hinges are mounted in the same line. Keep some space about mm width between elevator and tailing edge. 58 Mount the fuel tank to the fuselage. Canopy Tailing edge mm Elevator Wood dowel (x30mm) Former for fuselage mm Stab joiner (x0mm) Make sure they are in the right position while installing. Cowling former Fuel tank (550cc) (3xmm) TP Screw(3x0mm)
9 5 Screw (5mm) (Not included) (5mm) (Not included) Spring (5mm) (Not included) (Not included) Linkage Stopper Plastic tube (x50mm) Blind Nut (5mm) Fuel tank (550cc) Drill four holes at the diameters as show for engine mount. Glue the elevator to the stabilizer by CA and epoxy. Assemble the elevator sever to appropriate position in the fuselage. 37 Connect the elevator and the servo via the steel wire. 3mm.mm 3 Blind Nut Blind Nut (5mm) 53 The front view when the 50cc engine install completion. Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! 3 Assemble the engine. Assembly of the stabilizer. Make sure to glue securely. If not properly glued, a failure in flight may occur. Securely glue together.if coming off during flights, you'll lose control of your airplane which leads to accidents! Temporarily fasten down the main wing and check its correct position. (5mm) A B A' B' Elevator servo steel wire Screw (5mm) A=A' B=B' 5 5 The side view when the 50cc engine install completion. 73mm 35 Assemble the servos and switch. Install the servo. Pin hinge(.7x70mm) Screw (x0mm) (x5mm) Set screw (3xmm) Ball joint Lock Nut (mm ) (mm) Lock Screw (3x80mm) (mm) Linkage Stopper (mm) Nut (mm) Set screw (3xmm) 0 (3x5mm) Steel wire Screw (x0mm) Nut (mm ) (x5mm) Plastical tube(3x30mm) Screw (x0mm) Nut (mm ) (x5mm) 7 3
10 38 Drill holes to appropriate position in the rudder and epoxy the ping hinges in them Drill a hole to the appropriate position through the rudder as illustration. Bushing (Xmm) Screw (3x50mm) 30mm 7 Assemble the tail wheel to the tail retract. Lock Wheel (5mm) Install the servo. Screw (x0mm) (x5mm) Ball joint Lock Nut (mm ) Lock Bushing (Xmm) 5mm Steel wire 95mm 3mm Screw (x0mm) Pin hinge(.7x70mm) Make sure hinges are mounted in the same line mm 3 Epoxy the fibreglass tubes to appropriate position as below and leave some space with width of mm between tailing edge and rudder. The sketch map after the rudder shaft assemble finished. Nut (mm ) Note:rubber wheels oleo struts and retracts are optional. 5 (x5mm) Fix the tail oleo strut mount to the appointed position with screw as illustration. 8 Assemble the servos for the rudder and tail wheel to appropriate position in the fuselage. 9 The scatch map of the servo wires position inside the fuselage. Tailing edge Cut away the rubber tube when the epoxy glue dried. Rudder Steel wire (3x5mm) Lock Make sure they are in the right position while installing. 3 Drill holes to the relevant position in the tailing edge and epoxy the rudder to them. Screw (3x80mm) Aluminum tube mm 0 Screw (x5mm) Lock (3x5mm) Screw (3x80mm) Screw (x5mm)(not included) (xmm)(not included) The sketch map of the linkage for the rudder and the tail wheel. (xmm) Blind Nut Find out the proper position and set blind nut in them, using screw to fix the tail wheel arm as illustration. 5.mm Wire for elevator servo Blind Nut (xmm).5mm Screw (x5mm) Wire for rudder servo Wires for tail wheel mm Screw (x5mm)(not included) Blind Nut (mm)(not included) 8 (xmm)(not included) 9
Hawker hurricane MK.IIa
Hawker hurricane MK.IIa Specification: Length :00 mm(") Wing Span :00 mm(") Wing Area :0. sq. dm.9 sq. ft Wing Loading :.9 g/sq. dm 5.9 oz/sq. ft Flying Weight :.kg(5 lbs) Radio :ch& servos Engine :0 INSTRUCTION
More informationF - 4u Corsair (50cc)
F - u Corsair (50cc) Specification: Length: 73(.3") Wing span: 0mm(5") Wing area: 7.00sq.dm(9.39sq.ft) Wing loading: 35.g/sq.dm(.5oz/sq.ft) Flying weight:.kg(.0lbs) Radio: ch & 0servos Engine: 50cc gasoline
More informationSPITFIRE MK.XIV\XIX RUDDER
70 Adjustment. 7 The centre of the Gravity. Side View SPITFIRE MK.XIV\XIX RUDDER Top view 0mm 0mm 0mm Two wheel retract system Make sure to assemble retracts as instructed below. -way pressure inlet Strut
More informationP-39 Airacobra INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification: 30cc gasoline engine. This R/C airplane is not a toy!
P-39 Airacobra Specification: Length: Wing span: Wing area: Wing loading: Flying weight: Radio: Engine: 7mm(70. ) 00mm(0.3 ) 7.5sq.dm(.5sq.ft) 93g/sq.dm(30.5oz/sq.ft) 7.3kg(.bs) ch & servos 30cc gasoline
More informationT-28 Trojah INSTRUCTION MANUAL SAFETY PRECAUTIONS
T- Trojah Specification: Length :3 mm(3.5") Wing Span :057 mm(") Wing Area :70. sq. dm 7.55 sq. ft Wing Loading :7 g/sq. dm 39.5 oz/sq. ft Flying Weight :. kg( lbs) Radio :ch & servos Engine :0 -cycle
More informationFocke-Wulf Fw 190 RUDDER
7 Adjustment. 7 The centre of the Gravity. Side View Focke-Wulf Fw 90 RUDDER Top view 0mm 0mm 0mm Two wheel retract system Make sure to assemble retracts as instructed below. -way pressure inlet Strut
More informationP-47D Thunderbolt. Two wheel retract system Make sure to assemble retracts as instructed below. 3-way pressure inlet INSTRUCTION MANUAL
70 Adjustment. 7 The centre of the Gravity. Side View AILERON FLAP 0mm 0mm P-7D Thunderbolt AILERON FLAP 0mm 3mm Two wheel retract system Make sure to assemble retracts as instructed below. 3-way pressure
More informationF - 4u Corsair INSTRUCTION MANUAL SAFETY PRECAUTIONS. Two wheel retract system. Specification:
Adjustment. 3 The centre of the Gravity. Never fly before checking CG s required position. In order to obtain the CG specified reposition the receiver and battery. ELEVATOR Top view F - u Corsair 0mm 0mm
More informationPilatus PC-9 INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Pilatus PC-9 Specification: Length: Wing span: Wing area: Wing loading: Flying weight: Radio: Engine: 9mm(7 ) 0mm(0 ) sq.dm(.9sq.ft) 0.g/sq.dm(.9oz/sq.ft).kg(7.bs) ch & servos 0 -cycle 0cc gasoline engine
More informationAichi D3A1 INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Aichi D3A Specification: Length: 50mm(0. ) Wing span: 057mm( ) Wing area: 7.sq.dm(.sq.ft) Wing loading: 99.9g/sq.dm(3.oz/sq.ft) Flying weight: 7.kg(.7lbs) Radio: ch & 7servos Engine: 0 -cycle C.G: 35mm
More informationB-25 Mitchell INSTRUCTION MANUAL SAFETY PRECAUTIONS
B-5 Mitchell Specification: Length :935 mm(76.") Wing Span :0 mm(95") Wing Area :77.6 sq. dm 7./sq.ft Wing Loading : g/sq. dm oz/sq. ft Flying Weight :0 kg(. lbs) Radio :6ch&3 servos Engine(a pair) :9
More informationJU-87D Stuka INSTRUCTION MANUAL SAFETY PRECAUTIONS
73 Adjustment. 7 Centre of Gravity. Side View AILERON FLAP 0mm 0mm JU-7D Stuka 30mm Top View AILERON FLAP 35mm 75 The front view when the drop tank and the bombs install completion. Specification: Length
More informationModellbau Lindinger GmbH Modellbau Lindinger GmbH
7 Adjustment. 7 Adjustment. AILERON 5mm 5mm RUDDER Robin 0 FLAP 0mm Top view 30mm 30mm Side View AILERON FLAP 73 Adjustment. ELEVATOR Side View 5mm 5mm Top view Position for right diagram. 7 Centre of
More informationCessna 185 INSTRUCTION MANUAL SAFETY PRECAUTIONS
Cessna Specification: Length :0 mm(") Wing Span :00 mm(.") Wing Area :. sq. dm.9 sq. ft Wing Loading :7. g/sq. dm. oz/sq. ft Flying Weight :. kg(. lbs) Radio :ch&9 servos Engine :0 -cycle 0 -cycle INSTRUCTION
More informationBeaver INSTRUCTION MANUAL SAFETY PRECAUTIONS. 1.8mm. Specification:
9 Fix the aluminum bracket on the fuselage with screw. 95 The floats installation finished. Screw (x5mm) 9 Blind Nut (mm) 9 Washer (xmm) 9 Screw (x5mm) Beaver Damped nut (mm) Washer (xmm) Screw (x5mm)
More informationSpitfire Mk.IX ARF. Electric retract system. TopRCModel-USA.com
Electric retract system Thank you very much for purchasing our TRCM optional electric retract set, all our products were passed strict QC before they shipped out to the customers. In order to avoid probably
More informationFOKKER D-VII INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
FOKKER D-VII Specification: Length Wing Span Wing Area :97 mm(55") :77 mm(70") :9sq.dm 9.sq.ft Wing Loading :59.g/sq.dm.9oz/sq.ft Flying Weight :.5kg(lbs) Radio Engine: :ch & 5servos :cc-cc INSTRUCTION
More informationAdrenaline. Specification: 5.5 sq. ft Wing Loading :82 g/sq. dm 26.9 oz/sq. ft Flying Weight :4.2 kg(9.3 lbs) :6ch&6 servos.
Adrenaline Specification: Length Wing Span Wing Area :70 mm(7") :70 mm(") :5. sq. dm 5.5 sq. ft Wing Loading : g/sq. dm.9 oz/sq. ft Flying Weight :. kg(9. lbs) Radio :ch& servos Engine :0 -cycle 0 -cycle
More informationCessna INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Cessna - 95 Specification: Length Wing Span Wing Area :00 mm(") :7 mm(07") :0sq.dm.9sq.ft Wing Loading :75g/sq.dm.oz/sq.ft Flying Weight :9kg(9.lbs) Radio Engine: :ch & servos :0cc-50cc INSTRUCTION MANUAL
More informationAdmas A500. Specification:
Admas A500 Specification: Length :07 mm(8.7") Wing Span :00 mm(9.5") Wing Area :8.8 sq. dm 5.5 sq. ft Wing Loading :3 g/sq. dm 53.7 oz/sq. ft Flying Weight :8 kg(7.lbs) Radio :ch &3 servos Engine : -cycle
More informationLTR-14 TURNER SPECIAL
LTR- TURNER SPECIAL Specification: Length Wing Span Wing Area :05 mm(8") : mm(95") :sq.dm sq.ft Wing Loading :0g/sq.dm 5.oz/sq.ft Flying Weight :kg(.lbs) Radio Engine: :ch & 8servos :80cc-00cc INSTRUCTION
More informationZlin Z-526 AFS INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Zlin Z-5 AFS Specification: Length Wing Span Wing Area :75 mm(7.") :05 mm(") :7.sq.dm.9sq.ft Wing Loading :70.9g/sq.dm.oz/sq.ft Flying Weight :5.kg(.9lbs) Radio :ch & servos Engine: :cc-cc INSTRUCTION
More information第 4 页. 3. Apply instand type AB glue to the holes in the aileron and hinges. Epoxy the aileron to the wing.
TopRCModel-USA.com TopRCModel-USA.com TopRCModel-USA.com Accessory list for the installation of aileron and flap. 3. Apply instand type AB glue to the holes in the aileron and hinges. Epoxy the aileron
More information第 4 页, 共 17 页. 3. Epoxy the wood block to the servo tray base on the mark line. Accessory part lists for wing installation.
第 1 页, 共 17 页 第 2 页, 共 17 页 第 3 页, 共 17 页 Accessory part lists for wing installation. 3. Epoxy the wood block to the servo tray base on the mark line. 1. Ready for assemble the wing servos. 4. Epoxy the
More information105" TIGER MOTH ARF INSTRUCTION MANUAL VERSION 1.0
105" TIGER MOTH ARF INSTRUCTION MANUAL VERSION 1.0 Step 1. Installation of the aileron servos 1) Mount aileron servo to servo mounting blocks with servo s screws. Install servo mounting plate with screws.
More informationSpecifications. Before commencing assembly, please read these instructions thoroughly.
INSTRUCTION MANUAL Before commencing assembly, please read these instructions thoroughly. Specifications Wing Span: 8.5 in / 30 mm Wing Area: 330 sq in /.3 sq dm Flying Weight: 6 oz / 70 g Fuselage Length:
More informationSpecifications. Before commencing assembly, please read these instructions thoroughly. INSTRUCTION MANUAL
INSTRUCTION MANUAL Before commencing assembly, please read these instructions thoroughly. Specifications Wing Span: 50 in / 170 mm Wing Area: 484 sq in / 31. sq dm Flying Weight: 3.5 lbs / 1600 g Fuselage
More informationTIGER MOTH 120 ASSEMBLY INSTRUCTIONS
TIGER MOTH 120 ASSEMBLY INSTRUCTIONS SPECIFICATIONS Wing Span: Length: Radio: Flying Weight: 1920mm 1580mm 4 channel with 6 servos 4200g AILERON ASSEMBLY 1 Start by removing the servo cover from the bottom
More informationFUSELAGE CONSTRUCTION
FUSELAGE CONSTRUCTION Note: prior to building and gluing on the work surface use protective covering on your building surface. (wax paper or clear wrap) Fit the laser cut Fuselage Front and Fuselage Rear
More informationAure. Radio required : 3 channels, 4 servos airplane radio. Specifications. * Specifications are subject to change without notice.
A L M O S T- R E A D Y- T O - F LY Aure INSTRUCTION MANUAL Radio required : 3 channels, 4 servos airplane radio Specifications Wing Span Wing Area Flying Weight Fuselage Length 81.5 in / 2070mm 572.0 sq
More informationRYAN STA SAFETY PRECAUTIONS. "Sport Scale E-Power ARF" For Intermediate and Advanced Fliers. This radio control model is not a toy!
RYAN STA "Sport Scale E-Power ARF" For Intermediate and Advanced Fliers. SAFETY PRECAUTIONS This radio control model is not a toy! First-time builders should seek advice from people with model building
More informationINSTRUCTION MANUAL. Specifications. Wing Area Flying Weight Fuselage Length. 28 oz / 800 g 30.0 in / 760 mm
ALMOST-READY-TO-FLY INSTRUCTION MANUAL Requires : -channel radio w/ micro servos, Outrunner Motor w/ Propeller Adaptor 0A Brushless ESC, 3 cells 11.1V 100 mah Li - Po battery & charger. Wing Span Wing
More informationMECOA EZ-4061 Trainer
MECOA EZ-4061 Trainer EZ-4061 is a newly designed, Almost Ready to Fly kit. It is an extremely easy to control trainer with strong construction and excellent aerodynamic performance. This is a great choice
More informationCorvus Racer CC
Corvus Racer 540 35CC Item No:L-G035008 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio mm mm 1200sq in (77.4sqdm) 9.9-12lbs(4.5-5.5kg) 91-1.20(2C) 1.10-1.40(4C) 20-40cc
More informationSkymaster ARF F-18E Instructions Manual
Skymaster ARF F-18E Instructions Manual first: Take out the front servos mount, install front fuel tank before installing nose cone connect nose cone to fuselage by 6 screw Take out the 6 screws and Bottom
More informationLANDING GEAR. 1. Fit landing gear into slots on bottom of fuselage.
LANDING GEAR 1. Fit landing gear into slots on bottom of fuselage. 4. Use channel-lock pliers to press blind nuts into position (note: drilled hole should be slightly smaller than shaft of blind nut for
More informationEXTRA 330SC 60CC. Item No:H G Specifications cc gas DA50,DA60, DLE55, DLE60(twin), 3W55. Description
EXTRA 330SC 60CC Item No:H G060011 Specifications Wing Span Length Wing Area Flying Weight Gasoline Radio Description Carbon Fibre : 92" (2347mm) 84 1/2 " (2060mm) 1526.8 sq in(98.5sq dm) 16 17lbs(7300
More informationEdge 540 V3 35CC. Scheme A. Item No:L G Specifications. Flying Weight
Edge 540 V3 35CC Item No:L G035016 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio Description 76 (1930mm) 74 (1879mm) 1200sq in(77.4sqdm) 9.9 12lbs(4.5 5.5kg) 91 1.20(2C)
More informationInstruction Manual. Specification:
Instruction Manual H I G Specification: Wingspan: 133 cm (52.3 inches) Length : 104 cm (40.9 inches) Weight : 1830gr Engine : 25-32 two stroke Radio : 4 channel - 4 servo H W I N G KIT CONTENTS: We have
More informationVIPER 140 Manual. Release 1.0 January 2018
VIPER 140 Manual Release 1.0 January 2018 Please read this user manual carefully, it contains instructions for the correct assembly of the model. Please refer to the web site www.harlock-rc.com for updates
More informationAT channel 6 servos
Wing Span: Wing Area: Fuselage Length: Flying weight: Power system: Radio: 60.7in/1540mm 561 sq in/36.3 sq dm 44.1in/1120mm 6.9 Ibs/ 3100g 46(2C0/71(4C) 5 channel 6 servos AT6-46 INSTALLING AILERONS Begin
More informationMXS R 30CC. Item No:L G Specifications. 67 1/2"(1720mm) (2C) (4C) 26 35cc gas DLE 30/35RA MLD35 JC30Evo.
MXS R 30CC Item No:L G030008 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio Description Covering Material Carbon Fibre : 75"(1915mm) 67 1/2"(1720mm) 1023sq in(66sq
More informationCitabria Pro. Aerobatic Parkflyer. by Joel Dirnberger
Citabria Pro Aerobatic Parkflyer by Joel Dirnberger Revision C: December 21, 2004 Citabria Pro Building Instructions Length: Wingspan: Wing Area: Flying Weight: Wing Loading: Functions: Specifications:
More information30% Edge 540T Almost Ready to Fly
Lanier R/C 30% Edge 540T Almost Ready to Fly WARNING! THIS IS NOT A TOY! THIS IS NOT A BEGINNERS AIRPLANE This R/C kit and the model you will build from it is not a toy! It is capable of serious bodily
More informationInstruction Manual book
Instruction Manual book ITEM CODE BH53. SPECIFICATION Wingspan : 1,250mm 49.21 in. Length : 930mm 36.61in. Weight : 1.1kg 2.42 Lbs. Parts listing required (not included). Battery: 3 CELLS-LI-POLY-11.1V-2,500
More informationINSTRUCTION MANUAL BOOK.
INSTRUCTION MANUAL BOOK. SPECIFICATION Wingspan : 164 cm 64.57in. Length : 135 cm 53.15 in. Weight : 3.3kg 7.26 lbs. Servo : 7 servos. Radio : 4 channels. Engine : 61 cu.in-2 stroke. 91 cu.in-4 stroke.
More informationRESolution V2 Manual
RESolution V2 Manual Note for the German Manual: Yellow Bottle thick CA Pink Bottle Med CA Blue tube 5 minute Epoxy Green tube 90 Minute Epoxy Construction of the Fuselage Step 1: Cover the plan with a
More informationHigh performance 90mm fiberglass jet
High performance 90mm fiberglass jet Assembly manual For intermediate and advanced fliers only! Specs Wingspan: 1255mm Fuselage length: 1250mm Flying weight: 2600-3000g Wing area: 22.6 dm² Wing loading:
More informationExtra 330LT CC. 2 Colour schemes H-G120001A ORACOVER FERRARI RED # ORACOVER WITH # ORACOVER BLACK # ORACOVER SILVER #
Extra 330LT 85-125CC Item No:A-G120001 Specs: WING SPAN: LENGTH: WING AREA: FLYING WEIGHT: ENGINE: RADIO: Description Covering Material Carbon Fibre: 111 (2833mm) 100" (2530mm) 2139sq in (138sq dm) 25.3-28lbs
More informationCorvus Racer Colour schemes. AeroPlus RC Copyright 2013 All Rights Reserved
Corvus Racer 540 59 Item No:A E050003 Specifications WING SPAN: 59"(1500mm) LENGTH: 54.1"(1374mm) WING AREA: 654sq.in.(42.2sq.dm.) FLYING WEIGHT: 4.6 5.3lbs(2000 2300g) Electric:Brushless outrunner 8Oz.
More informationBOOMERANG TORUS. Aerobatic Sport Jet for 20 to 34 lbs (P80 to P160) thrust turbines.
BOOMERANG TORUS Aerobatic Sport Jet for 20 to 3 lbs (P80 to P160) thrust turbines. Specifications: Span... 83" (2209mm.) Span with Wingtip Tanks 90" (2286mm.) Length...87" (2108mm.) Weight 29 Lbs.(13.15
More informationInstruction Manual. Item No: AL001
Instruction Manual Item No: AL001 Specifications: Wingspan: 2037mm (80.2 in) Length: 1677mm (66 in) Wing Area: 65.5dm2 (1015.3 sq in) Flying Weight: 7.6kg (16.7 lbs) Engine(not incl.): 45-50cc Gas Radio(not
More informationC-180 Builder s Manual
C-180 Builder s Manual. May 20, 2002 Last revised July 11, 2002 Copyright! 2002 Douglas Binder, Mountain Models www.mountainmodels.com sales@mountainmodels.com (719) 630-3186 1 Required Equipment! Xacto
More informationTHE APOGEE A 100-INCH AMA DURATION SAILPLANE FROM DYNAFLITE
THE APOGEE A 100-INCH AMA DURATION SAILPLANE FROM DYNAFLITE Apogee is the intermediate sailplane designed to be competitive in AMA duration contests. Effective spoilers, rudder and full flying stabilizer
More informationBUILDING THE A6M2 ZERO
BUILDING THE A6M2 ZERO Product Support (Do Not Remove From Department) TOP FLITE MODELS, INC CONGRATULATIONS' You now own the most accurate R/C Stand-Off Scale kit ever produced We at Top Flite hope that
More information90 WING SPAN P-51D MUSTANG (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED
90 WING SPAN P-51D MUSTANG (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED GENERAL INSTRUCTIONS This design is basically an enlargement of the very popular fun scale Mustang 60 Size. You can build it light
More informationPITTS S2S CONSTRUCTION
PITTS S2S CONSTRUCTION FUSELAGE CONSTRUCTION 1) Place the right fuselage side over the plan and mark the former positions. Place the left side over the right side and mark the former positions. Glue F1
More informationF3A -70E ASSEMBLY MANUAL
F3A -70E ASSEMBLY MANUAL The new F3A-70E, was designed in an extremely lightweight structure, the all wood airframe, and the new revolutionary Lift Generator on landing gear give the F3A-70E an impressive
More informationPERCIVAL P-56 PROVOST
Instruction Manual Book. PERCIVAL P-56 PROVOST OLEO STRUTS LANDING GEAR. ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER Glow and EP 95% ALMOST READY TO FLY SPECIFICATION: - Wingspan: 1,644mm
More informationAssembly Instructions. Stinger 120. Almost Ready to Fly
Stinger 120 Almost Ready to Fly Important Information: Please inspect the plane before beginning to assemble to make sure you are happy with it. After assembly has begun you cannot return the kit. If you
More informationSPUNKY ASSEMBLY MANUAL
SPUNKY ASSEMBLY MANUAL Please read the tips section at the back of this manual regarding the use of laser cut parts. The proper removal and preparation of these parts is important. When laser cut, some
More informationFAIREY ALBACORE. Instruction Manual Book. Glow and EP. Item code: BH % ALMOST READY TO FLY SPECIFICATION:
Instruction Manual Book. FAIREY ALBACORE ALL BALSA - PLY WOOD CONSTRUCTION. COVERED IN A HEAT-SHRINK FILM WITH PRINTED. Glow and EP 95% ALMOST READY TO FLY SPECIFICATION: - Wingspan: 1,693mm (66.65in).
More informationFUJI FA-200 AERO SUBARU
FUJI FA-200 AERO SUBARU SEMI SCALE SPORT MODEL AERO SUBARU Assembly and Operations Manual Please review this manual throughly Before assembling or Operating The AERO SUBARU Semi scale sport model We ve
More informationPROCTOR. Instruction Manual Book 95% ALMOST READY TO FLY. Item code: BH154. SPECIFICATION ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER
Instruction Manual Book PROCTOR Item code: BH154. ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER 95% ALMOST READY TO FLY SPECIFICATION Wingspan: 1,360 mm (53.54 in). Length: 1,480 mm(58.27 in).
More informationTWEETY 25 INSTRUCTION MANUAL. Almost Ready to Fly Nitro/Electric Aerobat FEATURES SPECIFICATIONS
TWEETY 25 Almost Ready to Fly Nitro/Electric Aerobat INSTRUCTION MANUAL SPECIFICATIONS FEATURES WINGSPAN: 45.7 (1160mm) LENGTH: 38.6 (980mm) WING AREA: 370 sq in(24 sq dm) FLYING WEIGHT: Approx. 3.3 lbs
More informationJUNKERS JU87- B2 STUKA
Instruction Manual Book Item code: BH169. JUNKERS JU87- B2 STUKA OLEO STRUTS LANDING GEAR. ALL BALSA - PLY WOOD CONSTRUCTION. COVERED IN A HEAT-SHRINK FILM WITH PRINTED. 95% ALMOST READY TO FLY SPECIFICATION:
More informationSZD-10 bis CZAPLA ASSEMBLY MANUAL IN PICTURES
1 RUDDER Plan and parts: 2 Assembly steps: Photo above: glue together rudder spar, ribs and trailing edge. Clamp spar to a flat surface (chipboard on the photo) and make sure the straight aligment of the
More information96 WING SPAN SPITFIRE (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED
96 WING SPAN SPITFIRE (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED GENERAL INSTRUCTIONS Should you elect to use the recommended Door Skin, which is 1/8 mahogany plywood measuring 36 x 88. Have it cut
More information94 Yak 54 ARF WARNING
94 Yak 54 ARF WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that could be dangerous.
More informationSuper Sky Surfer 2000 Assembly Instructions
Super Sky Surfer 2000 Assembly Instructions Note: Plug and Play version of the Sky Surfer comes with fuselage pre-glued and motor/servos installed. If you wish to route antennas or wires through the tail,
More informationEPP EAGLE THE RC RAPTOR
EPP EAGLE THE RC RAPTOR Installation Manual FLYEAGLE2007@GMAIL.COM TM Step 1: Verify that all the EPP Eagle pieces are included in the Kit. Before we start. Step 2: Identify the pieces need to assemble
More information(Build Instructions)
(Build Instructions) Specifications * Wingspan: 58cm * Length: 50cm * Flying Weight: 59 grams * Channels: 3 (Rudder Elevator Throttle) * Suggested Receiver: 4Ch Micro * Motor: 8mm GearDrive * Prop: GWS
More informationPreliminary pilot information
Recommended RC-components: Preliminary pilot information RC-component suggestions for Freestyler 3, V-tail version FLAPS AILERONS V-tail receiver battery low-cost HS85 MG HS85 MG HS81 MG SMC 14 4 x AA
More informationRADIO CONTROL MODEL / RC FLUGMODELL INSTRUCTION MANUAL
RADIO CONTROL MODEL / RC FLUGMODELL INSTRUCTION MANUAL SPECIFITIONS Wingspan...57.5 in. / 146cm Length...50 in. / 127cm Engine...46 2T /.70 4T or Electric equivalent. Radio...4 ~ 6 channel Almost ready
More informationBUCKER BU 131 JUNGMANN ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER
Instruction Manual Book. BUCKER BU 131 JUNGMANN ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER Glow and EP 95% ALMOST READY TO FLY SPECIFICATION: - Wingspan: 1,850 mm (72.83 in). Length: 1,660
More informationHand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL
Hand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL Specifications Wingspan -----------------------.148 cm--------------- 58.3 in. Wing area ----------------------- 3474sq. cm ---- 538.4sq
More informationHIGH-END TECHNOLOGY. Electric ducted fan Starfighter
HIGH-END TECHNOLOGY RC Electric ducted fan Starfighter First we want to thank and congratulate you with your decision in buying one of our Kits. The Starfighter puts together very easily so there is not
More informationVelocity Slingjet. Specifications: Construction Span Length Take-off weight w/ gear. Balsa/foam/film 1055m m (41.54 ) 1040m m (40.
Velocity Slingjet Specifications: Construction Span Length Take-off weight w/ gear Recommended servos w/o nose-steering Recommended fan Recommended motor Recommended controller Balsa/foam/film 1055m m
More informationMUSTANG P-51. Hand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL
MUSTANG P-51 Hand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL Specifications Wingspan---------------------------------------- 60.5 in----------------------- 153.7cm. Wing area-------------------------------------
More informationAssembly Instructions STINGER
STINGER 120 ARF Important Information: Please inspect the plane before beginning to assemble to make sure you are happy with it. After assembly has begun you cannot return the kit. If you find a problem
More informationHot Stik ARF WARNING. Copyright 2005 Carl Goldberg Products LTD CARL GOLDBERG PRODUCTS, LTD.
Hot Stik ARF INSTRUCTIONS WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that
More informationBashing The Hanger 9 Cessna 182 ARF Part 4
Bashing The Hanger 9 Cessna 182 ARF Part 4 Eric Helms Pongo Air This is the final installment of a four-part article covering a variety of modifications incorporated into a Hanger 9 Cessna 182 ARF. Upgrades
More informationHAWKER HURRICANE. Instruction Manual Book 95% ALMOST READY TO FLY. Item code: BH147. SPECIFICATION
Instruction Manual Book Item code: BH147. HAWKER HURRICANE ALL BALSA - PLY WOOD CONSTRUCTION. COVERED IN A HEAT-SHRINK FILM WITH PRINTED. 95% ALMOST READY TO FLY SPECIFICATION Wingspan: 1,520 mm (59.84
More informationDORNIER DO 27 SEMI SCALE SPORT MODEL DORNIER DO 27. Please review this manual throughly Before Assembling or Operating The DORNIER DO 27
DORNIER DO 27 SEMI SCALE SPORT MODEL DORNIER DO 27 Assembly and Operations Manual Please review this manual throughly Before Assembling or Operating The DORNIER DO 27 Semi Scale Sport Model We ve used
More informationSig Mfg. Co., Inc South Front Street...Montezuma, Iowa 50171
Sig Mfg. Co., Inc...401-7 South Front Street...Montezuma, Iowa 50171 Introduction The SEALANE takes off and lands on water just as easy as the Sig Kadet LT40 does on solid ground. Gentle, graceful, sure
More informationDORNIER DO 27 SEMI SCALE SPORT MODEL DORNIER DO 27. Assembly and Operations Manual
DORNIER DO 27 SEMI SCALE SPORT MODEL DORNIER DO 27 Assembly and Operations Manual Please review this manual throughly Before assembling or Operating The DORNIER DO 27 Semi scale sport model We ve used
More informationLANIER R/C. Stinger WARNING! THIS IS NOT A TOY! THIS IS NOT A BEGINNERS AIRPLANE LIMITED WARRANTY
LANIER R/C Stinger WARNING! THIS IS NOT A TOY! THIS IS NOT A BEGINNERS AIRPLANE This R/C kit and the model you will build from it is not a toy! It is capable of serious bodily harm and property damage.
More information87 Extra 330 ARF WARNING
87 Extra 330 ARF WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that could be
More informationLANIER - Double Trouble - INSTRUCTIONS. Tail 1 T1 ¼ Balsa 1 T2 ¼ Balsa 2 T3 ¼ Balsa 1 T4 ¼ Balsa 1 T5 ¼ Balsa 1 T6 ¼ Balsa 2 J1 ¼ Balsa 2 J2 Lite ply
Tail 1 T1 ¼ Balsa 1 T2 ¼ Balsa 2 T3 ¼ Balsa 1 T4 ¼ Balsa 1 T5 ¼ Balsa 1 T6 ¼ Balsa 2 J1 ¼ Balsa 2 J2 Lite ply Other Parts 2 Aluminum Gear 1 3/32 Music wire tail skid 2 Elevator and J-plane joiner wire
More informationLARK. Classic Legal Precision Stunter RSM DISTRIBUTION. presents. Charles Mackey. Wing Area 570sq. Wingspan 52.
RSM DISTRIBUTION presents LARK By Charles Mackey Photo _ Bob Hunt Classic Legal Precision Stunter Wingspan 52 Length 39.5 Wing Area 570sq Motor 35-46 www.rsmdistribution.com Page 2 Thank you for purchasing
More informationNote - the nose ribs and are thinner than the main ribs. These nose ribs will use a thinner rib cap than the ribs. This is per design.
Stabilizer rev 1.2 The SE5a stabilizer is the heartbeat of the tail and is recreated like the full scale version. All tail pieces depend on the stabilizer. It uses the steel fittings, pulleys, inspection
More informationHIGH-END TECHNOLOGY. Electric ducted fan rafale
HIGH-END TECHNOLOGY RC Electric ducted fan rafale First we want to thank and congratulate you with your decision in buying one of our Kits. The Rafale puts together very easily so there is not much explanation
More informationSTEP 1 STEP 2 STEP 3. Page 2
INSTRUCTION MANUAL Congratulations on your purchase of the Bullet ARTF - the first Almost Ready to Fly version of this classic lowwinger. Based on the original and timeless Bullet design, the new Ripmax
More informationBuilding instructions. Grob G 109. RC motor-glider Order No. 1340/00. Specification: approx mm. RC functions:
Building instructions Grob G 109 RC motor-glider Order No. 1340/00 Specification: Wingspan Length Wing area Tailplane area Total surface area All-up weight with 12 cells Wing loading (wing only) approx.
More informationBuilding Instructions. Scarlet RC model aircraft. Order No. 1308/00. Specification: approx mm. rudder, flaps, throttle.
Building Instructions RC model aircraft Order No. 1308/00 Specification: Wingspan Length Wing area All-up weight Wing loading RC functions approx. 3000 mm approx. 1270 mm approx. 53.5 dm² approx. 1.45
More informationASSEMBLY & OPERATIONS MANUAL
TM TM AERO SUBARU 40-52 ARF ECS SEMI SCALE MODEL WITH POLYCOTE ECS ENHANCED GRAPHICS SYSTEM #VMA-S140B (blue as shown) #VMA-S140R (red) This model may be produced in a number of different graphic schemes
More informationNOORDUYN NORSEMAN. Instruction Manual Book 95% ALMOST READY TO FLY. Item code: BH157. SPECIFICATION
Instruction Manual Book Item code: BH157. NOORDUYN NORSEMAN ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER. 95% ALMOST READY TO FLY SPECIFICATION - Wingspan: 1840 mm (72.44 in). - Length: 1180
More information+++ construction manual SR 71 Blackbird (EDF Version) from JetCom +++
Table of content: Page List of material and overview of provided frames 3 Mounting of main gear 4 Mounting of nose gear 5 Mounting of elevons 6 Installation of the rudders 7 Mounting of the rudders 9 Installation
More informationParkJet Builder s Manual
ParkJet Builder s Manual Thank you for purchasing the ParkJet. The ParkJet is a profile ducted fan airplane that can be flown in a larger park. The ParkJet was initially designed by Scott Stoops and modified
More informationP-47 THUNDERBOLT TOP FLITE MODELS, INC.
Building the P-47 THUNDERBOLT 1976 - TOP FLITE MODELS, INC. Congratulations! You now own the most accurate R/C Stand-Off Scale kit ever produced. We at Top Flite hope that you will find this model the
More information