B-25 Mitchell INSTRUCTION MANUAL SAFETY PRECAUTIONS
|
|
- Annice Campbell
- 6 years ago
- Views:
Transcription
1 B-5 Mitchell Specification: Length :935 mm(76.") Wing Span :0 mm(95") Wing Area :77.6 sq. dm 7./sq.ft Wing Loading : g/sq. dm oz/sq. ft Flying Weight :0 kg(. lbs) Radio :6ch&3 servos Engine(a pair) :9 -cycle INSTRUCTION MANUAL SAFETY PRECAUTIONS This R/C airplane is not a toy! (The people under years old is forbidden from flying this model) First-time builders should seek advice from people having building experience.if misused or abused,it can cause serious bodily injury and damage to property. Fly only in open areas and preferably at a dedicated R/C flying site. We suggest having a qualified instructor carefully inspect your airplane before its first flight.please carefully read and follow all instructions included with this airplane,your radio control system and any other components purchased separately.
2 6 (with 3 servos), 6 6 channel radio for aiplane is highly recommended for this model. 6 : -cycle.9 Spinner nut "x7 Apply Warning Remove the covering with proper pressure to cut through only the covering itself.otherwise, cutting down into the balsa structure may weaken the model part and cause accident. Pre-cover the covering with clean cloth! Start at low setting. Increase the setting if necessary.if it is too high,you may damage the film. The pre-covered film on ARF kits may wrinkle due to variations of temperature.smooth out as explained right. with cover(cloth) Iow setting
3 Three wheel retract system Make sure to assemble retracts as instructed below. Strut 3-way pressure inlet 3-way pressure inlet Pin hinge(xmm) Rod (x300mm) TP Screw (.3xmm) Screw (3x0mm) Servo tray(6.5x56.5xmm) Wooden Block(0x0xmm) Pin hinge(xmm) Washer(3x5mm) Washer(3x5mm) 6 6 Apply instant type CA glue to aileron and pin hinge. 3 Assemble the aileron to main wing with instant type CA glue. Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! Install the servo as the illustration below Strut 3-way pressure inlet 3-way pressure inlet Strut Air inlet 3-way pressure inlet Air tank Make sure hinges are mounted in the same line. Quick release connector Pressure reduction inlet Quick release connector Ø0.mm Keep mm width space between aileron and trailing edge. 5 Install the nylon control horn and connect the linkage. Ø.7mm Switch Trailing edge Rod (x300mm) Aileron Air valve The status when the gear up Please insure the sealing of the retract system before flight. Pleas notice the inner diameter for each side of the pressure reduction inlet. Air valve Pull out length of mm to make gear down TP Screw(.6xmm) Rod (X300mm) Strut ( 0 ) Switch Air line (3000mm) 3-way pressure inlet Air tank Air inlet Quick release connector Strut ( 90 ) 5 Make sure they are in the right position while installing. mm Screw (x0mm)
4 6 Secure the servo.install the nylon control horn and connect the linkage. TP Screw (.3xmm) Leave some space with width of mm between trailing edge and flap. 96 Centre of Gravity. Trailing edge Rod (x300mm) Flap.5mm 3mm Screw (x0mm) Washer(3x5mm) mm Washer Screw (3x0mm) 9 Rod (x300mm) TP Screw (.3xmm) Screw (3x50mm) Servo tray(6.5x56.5xmm) Wooden Block(0x0xmm) Washer(3x5mm) Washer(3x5mm) Pin hinge(36x0xmm) PVC 7 Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! 0 Epoxy the pin hinges to the flap. Pin hinge(36x0xmm) Be careful to ensure the moving parts of the hinges are able to move freely. Epoxy the flap to the main wings. 6 PVC 5mm Make sure they are in the right position while installing. Install the servo as the illustration below 9
5 9 93 Epoxy the nose landing gear to appropriate position inside the fuselage. Adjustment. Install the nylon control horn and connect the linkage. Trailing edge Rod (x300mm) ELEVATOR Flap Top view 0mm Side View Screw (x0mm) 0mm mm Make sure they are in the right position while installing. Position for right diagram. 9 Keep some space of mm width between the flap and trailing edge Secure the servo.install the nylon control horn and connect the linkage. Adjustment. Side View TP Screw (.3xmm) Epoxy the flap to the mid wing..5mm Rod (x300mm) RUDDER Screw (x0mm) 5mm Washer(3x5mm) 5mm Washer Top view 95 Side View mm Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! Screw (3x50mm) 3 97 Adjustment. 6 Epoxy the pin hinges to the flap. AILERON FLAP 0mm AILERON 0mm FLAP 0mm Pin hinge(36x0xmm) 3 Install the servo as the illustration below
6 7 0 Install the nylon control horn and connect the linkage. 7 Glue these PVC parts to relevant position on the wings with CA glue. 9 Epoxy the decoration part to the fuselage carefully as below. Install the main landing gear and fix it to the wooden supporter steadily. Collar (5mm) PVC Rod (x300mm) Collar (5mm) mm TP Screw (3x0mm) Screw (x0mm) decorate Secure the servo.install the nylon control horn and connect the linkage. TP Screw (.3xmm) Rod (x300mm) Glue this PVC part to relevant position on the right wing. PVC Collar mm 3x0mm TP Screw Landing gear straps Mount the receiver and the battery to the fuselage. Wooden supporter 90 Epoxy the main landing gear to the side fuselage. 9 Install the nose landing gear as below..5mm 3mm 75mm Screw (x0mm) Washer(3x5mm) Washer Screw (3x50mm) 9 Cut off the surplus portion carefully along the shaded line. Screw (x35mm) Screw (x5mm) Washer(xmm) Spring Washer (mm) Nut (mm) Linkage Stopper Plastic tube (x00mm) Engine mount (06x6mm) Fuel tank (550cc) Blind Nut (mm) Hook screw Ply (30x30x9mm) Rubber band Wooden Block(56x9x6mm) Landing gear straps Wooden Block(9x9xmm) Wheel (75 mm) Wheel (5 mm) Collar (5mm) Steel wire (0.5x500mm) Landing gear (5mm) Copper joiner TP Screw(3x0mm) Landing gear (5mm) Ally nose arm Steel wire Aluminum tube Copper joiner Collar (5mm) Collar (5mm) 7 Collar mm 3 Add a rubber ring to the clevis for insuring safety Collar (5mm) 7
7 Epoxy plies to appropriate position in the fuselage under the PVC part and assemble the PCV part to the fuselage with TP screw as illustration. Epoxy the PVC part to the fuselage carefully as below. The front view and side view when the engine install completion. Assemble the accelerator push rod to the engine. Set Screw (3xmm) 7 mm Rod (x00mm) Linkage Stopper.5mm Ply (5x5X3mm) TP Screw (.3xmm) Washer (mm) Set Screw (mm) Set Screw (mm) 5 Epoxy the PVC part to the fuselage carefully as below. Set Screw (3xmm) In case of -cycle & -cycle engine. Epoxy the PVC part to the fuselage carefully as below. Drill four holes as show for engine mount. 5 The sketch map of the the push rod assemble completion 6 Fix the hook screw to wood block and epoxy the wood block to appropriate position in the side faselage as below. 5.mm 0mm 75mm Blind Nut 3 6 Epoxy the PVC part to appropriate position in the fuselage as illustration. Blind Nut (mm) Epoxy the PVC part to the fuselage carefully as below. 3 Assemble the engine as below. Screw (x35mm) Hook screw Washer (xmm) Rubber band mm Washer (xmm) 6 Washer (xmm) Spring Washer (mm) Nut (mm) Screw (x5mm) 5
8 7 3 Assembly of the fuel tank Assemble the throttle servos in the fuselage. 76 Assemble the switch servo to the fuselage. 7 Cut off the surplus part carefully along the shaded line. 77 Epoxy the belly pant to main wing and drill holes to relevant position on the belly pant. 79 Epoxy plies to appropriate position in the fuselage which under the fiber part and assemble the fiber part to fuselage with screw. Air pressure line Fuel spray line Fuel supply line Assembly of the fuel tank. Screw (x75mm) Washer (xmm) Screw (x5mm) Blind Nut (mm) TP Screw (.3xmm) TP Screw (3x0mm) Ply (5x5x3mm) Nut (mm ) Bushing (Xmm) Wheel (5 mm) Wood dowel (6x50x3mm) Decorate Fuel tank (550cc) 9 Reinforcement Plate 3 Install the servo. 6 6 TP Screw (.3xmm) Ply (5x5X3mm) Linkage Stopper Washer (mm) Nut (mm) Set screw (3xmm) Nut (5mm ) Bushing (Xmm) Wheel (0 mm) TP Screw (.3xmm) Decorate Note:rubber wheels oleo struts and retracts are optional. 6 0 Wheel (5mm) Nut (mm).5mm Assemble the rear wheels. Nut (mm) 6mm Bushing (Xmm) Set screw (3xmm) Washer (mm) Ply (5x5x3mm) Epoxy plies to appropriate position in the fiber part under the PVC part and assemble the PVC part to fiber parts with TP screw as illustration..5mm 5 Ply (5x5X3mm) TP Screw (.3xmm)
9 70 73 Trim the surplus portion for assemble the nose gear freely. Assemble the steeling fullarm around the landing gear Assemble the main landing gear. Cut off the surplus parts carefully along the shaded line the and epoxy them to yhe cowling. 0mm.5mm Decorate TP Screw(3x0mm) 7 7 Install the nose landing gear to appropriate position in the fuselage. TP Screw (3x0mm) Epoxy plies to appropriate position in the fuselage which under the nose gear cover and assemble the nose gear cover to fuselage with screw Epoxy the plies under the covering and assemble it to side fuselage with screw. epoxy the ply under cowling and assemble the cowling to side fuselage..5mm.5mm.5mm.5mm TP Screw (.3xmm) TP Screw (.3xmm) Ply (5x5x3mm) 7 75 Install the servo. Screw (x0mm) 6 Ply (5x5x3mm) 6 Ply (5x5x3mm) TP Screw (.3xmm) Assembly of the switch servo. 3 Trim the cowling for engine and muffler. Washer(x5mm) Ball joint Aluminum tube Lock Nut (mm ) Copper joiner Steel wire Copper joiner Aluminum tube(3x6mm) Screw (x0mm) Nut (mm ) Washer(x5mm) Add a rubber ring to the clevis for insuring safety Drill holes at appropriate position in the wing for fetching out the servo wire and air pipe.
10 39 Epoxy the side fuselage to the mid wing steadily. The standard sketch map when the main wing install completion. A Wood dowel (6x50x3mm) 0 Reinforcement Blind Nut (mm) 6.mm Blind Nut Screw (3x0mm) Hook screw Hook Main wing joiner(5x350mm) Wood dowel (6x50mm) Screw (3x0mm) 66 3 Fix the mid wing to the fuselage with the screws as illustration. Copper joiner Aluminum tube(3x6mm) TP Screw (3x0mm) Steel wire (0.5x500mm) TP Screw (.3xmm) Wheel (75 mm) Nut (mm ) Bushing (X6mm) Aluminum part(60x6mm) Screw (x0mm) Nut (mm ) Washer(x5mm) TP Screw (.3xmm) Ply (5x5x3mm) Screw(x75mm) Screw(x75mm) Drill holes on the wing root accorrding to rib template. 6mm 67 3.mm 6mm 69 Put the stabilizer to appropriate position on the fuselage and drill holes through the PVC,stabilizer until fuselage. 60mm Bushing (X6mm) Blind Nut Aluminum part(60x6mm) Wheel (75 mm) Nut (mm) Aluminum part(60x6mm) Wheel (75mm) Assemble the nose wheel. 0mm Screw(x35mm) Rib template (3mm ply) Glue this PVC part to appropriate position on the stabilizer with CA glue. 5mm Screw(x35mm) Washer(3x6mm) Washer(3x6mm) Rib template (mm ply) Assmble the stabilizer to the tail of fuselage with screw. A = A" Blind Nut 5mm 6 Cut off the surplus portion carefully along the shaded line. According to the reinforcement drill four holes to appropriate position in the mid wing and set blind nut in relevant fuselage position. 6.mm A" 65 Blind Nut (3mm) Nut (mm ) Bushing (X6mm) 3
11 60 Install the nylon control horn and connect the linkage. 7 Epoxy the wood dowel in the holes and set the hook screw to appropriate position Assmble the wing to the side fuselage tightly. Hook screw Wood dowel (6x50mm) Rod (x300mm) Screw (3x0mm) PVC 6 63 The position of the control horn in the rudder. Blind Nut (3mm) Washer(3x6mm) Screw (x0mm) Wood dowel (6x50mm) Main wing joiner(x350mm).5mm 60.5mm 5 Drill holes to appropriate position in the lead edge of stabilizer and epoxy wood dowels in them. Wood dowel (6x50mm) Drill holes to relevant position in the side fuselage according to rib template as below. The standard sketch map will be as below when the horizontal tail install completion. Make sure to glue securely. If not properly glued, a failure in flight may occur. Securely glue together.if coming off during flights, you'll lose control of your airplane which leads to accidents! Temporarily fasten down the main wing and check its correct position. 6mm 6mm 50mm B 0mm 0mm 6 6 Secure the servo,install the nylon control horn and connect the linkage. Rib template (3mm ply) Drill two holes to appropriate position in the fuselage as illustration. 6 B=B Drag the wing and the side fuselage together with the hook and rubber band. Rod (x300mm) TP Screw (.3xmm) Screw (3x0mm) TP Screw (.3xmm).5mm 6mm Rod (x300mm) 0mm 50mm Screw (x0mm) 3mm B Wooden Block(0x0xmm) Washer(3x5mm) Washer Hook Screw (3x0mm) Washer(3x5mm) Tailplane servo mount 9 Servo tray(6.5x56.5xmm) Pin hinge(xmm) Washer(3x5mm)
12 9 5 Drill one small hole at appropriale position and Apply instand type CA glue to elevator and pin higes. Pin hinge(xmm) Trim the covering carefully to appropriate position in the tailplane and epoxy the tailplane servo mount to the ready slot as illustration. 55 7mm 57 Keep mm width space between horizontal tail and rudder. The standard sketch map will be as below when the horizontal tail install completion. Make sure to glue securely. If not properly glued, a failure in flight may occur. Securely glue together.if coming off during flights, you'll lose control of your airplane which leads to accidents! Temporarily fasten down the main wing and check its correct position. Tailing edge 3mm Rudder C D mm 3mm 35mm 50 Tailplane servo mount Make sure hinges are mounted in the same line. 53 Keep some space about mm width between the elevator and horizontal tail edge. Assemnle the servo of the elevator. D C C=C D=D Make sure they are in the right position while installing. 56 Assemble the rudder to the vertical tail with CA glue. Pin hinge(xmm) Trailing edge 5 Epoxy the vertical tail to the stabilizer. 59 Install the medium servo as below. Elevator mm Add a rubber ring to the clevis for insuring safety Make sure they are in the right position while installing. 5 5 Assmble the elevator to the stabilizer with CA gule and the metal wire with epoxy glue. Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! Apply instant type CA glue to rudder and pin hinge. Pin hinge(xmm) 57 Cut off the surplus portion from the vertical tail carefully. Make sure they are in the right position while installing. Make sure hinges are mounted in the same line. Securely glue together. If coming off during flights, you 'll lose control of your airplane which leads to accidents! Polish the surface flat. 0
P-47D Thunderbolt. Two wheel retract system Make sure to assemble retracts as instructed below. 3-way pressure inlet INSTRUCTION MANUAL
70 Adjustment. 7 The centre of the Gravity. Side View AILERON FLAP 0mm 0mm P-7D Thunderbolt AILERON FLAP 0mm 3mm Two wheel retract system Make sure to assemble retracts as instructed below. 3-way pressure
More informationFocke-Wulf Fw 190 RUDDER
7 Adjustment. 7 The centre of the Gravity. Side View Focke-Wulf Fw 90 RUDDER Top view 0mm 0mm 0mm Two wheel retract system Make sure to assemble retracts as instructed below. -way pressure inlet Strut
More informationHawker hurricane MK.IIa
Hawker hurricane MK.IIa Specification: Length :00 mm(") Wing Span :00 mm(") Wing Area :0. sq. dm.9 sq. ft Wing Loading :.9 g/sq. dm 5.9 oz/sq. ft Flying Weight :.kg(5 lbs) Radio :ch& servos Engine :0 INSTRUCTION
More informationF - 4u Corsair INSTRUCTION MANUAL SAFETY PRECAUTIONS. Two wheel retract system. Specification:
Adjustment. 3 The centre of the Gravity. Never fly before checking CG s required position. In order to obtain the CG specified reposition the receiver and battery. ELEVATOR Top view F - u Corsair 0mm 0mm
More informationPilatus PC-9 INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Pilatus PC-9 Specification: Length: Wing span: Wing area: Wing loading: Flying weight: Radio: Engine: 9mm(7 ) 0mm(0 ) sq.dm(.9sq.ft) 0.g/sq.dm(.9oz/sq.ft).kg(7.bs) ch & servos 0 -cycle 0cc gasoline engine
More informationCessna 185 INSTRUCTION MANUAL SAFETY PRECAUTIONS
Cessna Specification: Length :0 mm(") Wing Span :00 mm(.") Wing Area :. sq. dm.9 sq. ft Wing Loading :7. g/sq. dm. oz/sq. ft Flying Weight :. kg(. lbs) Radio :ch&9 servos Engine :0 -cycle 0 -cycle INSTRUCTION
More informationT-28 Trojah INSTRUCTION MANUAL SAFETY PRECAUTIONS
T- Trojah Specification: Length :3 mm(3.5") Wing Span :057 mm(") Wing Area :70. sq. dm 7.55 sq. ft Wing Loading :7 g/sq. dm 39.5 oz/sq. ft Flying Weight :. kg( lbs) Radio :ch & servos Engine :0 -cycle
More informationModellbau Lindinger GmbH Modellbau Lindinger GmbH
7 Adjustment. 7 Adjustment. AILERON 5mm 5mm RUDDER Robin 0 FLAP 0mm Top view 30mm 30mm Side View AILERON FLAP 73 Adjustment. ELEVATOR Side View 5mm 5mm Top view Position for right diagram. 7 Centre of
More informationSPITFIRE MK.XIV\XIX RUDDER
70 Adjustment. 7 The centre of the Gravity. Side View SPITFIRE MK.XIV\XIX RUDDER Top view 0mm 0mm 0mm Two wheel retract system Make sure to assemble retracts as instructed below. -way pressure inlet Strut
More informationP-39 Airacobra INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification: 30cc gasoline engine. This R/C airplane is not a toy!
P-39 Airacobra Specification: Length: Wing span: Wing area: Wing loading: Flying weight: Radio: Engine: 7mm(70. ) 00mm(0.3 ) 7.5sq.dm(.5sq.ft) 93g/sq.dm(30.5oz/sq.ft) 7.3kg(.bs) ch & servos 30cc gasoline
More informationAdrenaline. Specification: 5.5 sq. ft Wing Loading :82 g/sq. dm 26.9 oz/sq. ft Flying Weight :4.2 kg(9.3 lbs) :6ch&6 servos.
Adrenaline Specification: Length Wing Span Wing Area :70 mm(7") :70 mm(") :5. sq. dm 5.5 sq. ft Wing Loading : g/sq. dm.9 oz/sq. ft Flying Weight :. kg(9. lbs) Radio :ch& servos Engine :0 -cycle 0 -cycle
More informationBeaver INSTRUCTION MANUAL SAFETY PRECAUTIONS. 1.8mm. Specification:
9 Fix the aluminum bracket on the fuselage with screw. 95 The floats installation finished. Screw (x5mm) 9 Blind Nut (mm) 9 Washer (xmm) 9 Screw (x5mm) Beaver Damped nut (mm) Washer (xmm) Screw (x5mm)
More informationAichi D3A1 INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Aichi D3A Specification: Length: 50mm(0. ) Wing span: 057mm( ) Wing area: 7.sq.dm(.sq.ft) Wing loading: 99.9g/sq.dm(3.oz/sq.ft) Flying weight: 7.kg(.7lbs) Radio: ch & 7servos Engine: 0 -cycle C.G: 35mm
More informationFw-190 D9(50cc) INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Fw-90 D9(50cc) Specification: Length: 00mm(8.5 ) Wing span: 093mm(8.5 ) Wing area: 77.79sq.dm(8.sq.ft) Wing loading: g/sq.dm(0oz/sq.ft) Flying weight: 9.5kg(0.9 bs) Radio: ch & 8servos Engine: 50cc gasoline
More informationCessna INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Cessna - 95 Specification: Length Wing Span Wing Area :00 mm(") :7 mm(07") :0sq.dm.9sq.ft Wing Loading :75g/sq.dm.oz/sq.ft Flying Weight :9kg(9.lbs) Radio Engine: :ch & servos :0cc-50cc INSTRUCTION MANUAL
More informationF - 4u Corsair (50cc)
F - u Corsair (50cc) Specification: Length: 73(.3") Wing span: 0mm(5") Wing area: 7.00sq.dm(9.39sq.ft) Wing loading: 35.g/sq.dm(.5oz/sq.ft) Flying weight:.kg(.0lbs) Radio: ch & 0servos Engine: 50cc gasoline
More informationJU-87D Stuka INSTRUCTION MANUAL SAFETY PRECAUTIONS
73 Adjustment. 7 Centre of Gravity. Side View AILERON FLAP 0mm 0mm JU-7D Stuka 30mm Top View AILERON FLAP 35mm 75 The front view when the drop tank and the bombs install completion. Specification: Length
More informationLTR-14 TURNER SPECIAL
LTR- TURNER SPECIAL Specification: Length Wing Span Wing Area :05 mm(8") : mm(95") :sq.dm sq.ft Wing Loading :0g/sq.dm 5.oz/sq.ft Flying Weight :kg(.lbs) Radio Engine: :ch & 8servos :80cc-00cc INSTRUCTION
More informationFOKKER D-VII INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
FOKKER D-VII Specification: Length Wing Span Wing Area :97 mm(55") :77 mm(70") :9sq.dm 9.sq.ft Wing Loading :59.g/sq.dm.9oz/sq.ft Flying Weight :.5kg(lbs) Radio Engine: :ch & 5servos :cc-cc INSTRUCTION
More informationZlin Z-526 AFS INSTRUCTION MANUAL SAFETY PRECAUTIONS. Specification:
Zlin Z-5 AFS Specification: Length Wing Span Wing Area :75 mm(7.") :05 mm(") :7.sq.dm.9sq.ft Wing Loading :70.9g/sq.dm.oz/sq.ft Flying Weight :5.kg(.9lbs) Radio :ch & servos Engine: :cc-cc INSTRUCTION
More informationAdmas A500. Specification:
Admas A500 Specification: Length :07 mm(8.7") Wing Span :00 mm(9.5") Wing Area :8.8 sq. dm 5.5 sq. ft Wing Loading :3 g/sq. dm 53.7 oz/sq. ft Flying Weight :8 kg(7.lbs) Radio :ch &3 servos Engine : -cycle
More informationSpitfire Mk.IX ARF. Electric retract system. TopRCModel-USA.com
Electric retract system Thank you very much for purchasing our TRCM optional electric retract set, all our products were passed strict QC before they shipped out to the customers. In order to avoid probably
More information第 4 页. 3. Apply instand type AB glue to the holes in the aileron and hinges. Epoxy the aileron to the wing.
TopRCModel-USA.com TopRCModel-USA.com TopRCModel-USA.com Accessory list for the installation of aileron and flap. 3. Apply instand type AB glue to the holes in the aileron and hinges. Epoxy the aileron
More information第 4 页, 共 17 页. 3. Epoxy the wood block to the servo tray base on the mark line. Accessory part lists for wing installation.
第 1 页, 共 17 页 第 2 页, 共 17 页 第 3 页, 共 17 页 Accessory part lists for wing installation. 3. Epoxy the wood block to the servo tray base on the mark line. 1. Ready for assemble the wing servos. 4. Epoxy the
More information105" TIGER MOTH ARF INSTRUCTION MANUAL VERSION 1.0
105" TIGER MOTH ARF INSTRUCTION MANUAL VERSION 1.0 Step 1. Installation of the aileron servos 1) Mount aileron servo to servo mounting blocks with servo s screws. Install servo mounting plate with screws.
More informationSpecifications. Before commencing assembly, please read these instructions thoroughly.
INSTRUCTION MANUAL Before commencing assembly, please read these instructions thoroughly. Specifications Wing Span: 8.5 in / 30 mm Wing Area: 330 sq in /.3 sq dm Flying Weight: 6 oz / 70 g Fuselage Length:
More informationAure. Radio required : 3 channels, 4 servos airplane radio. Specifications. * Specifications are subject to change without notice.
A L M O S T- R E A D Y- T O - F LY Aure INSTRUCTION MANUAL Radio required : 3 channels, 4 servos airplane radio Specifications Wing Span Wing Area Flying Weight Fuselage Length 81.5 in / 2070mm 572.0 sq
More informationSpecifications. Before commencing assembly, please read these instructions thoroughly. INSTRUCTION MANUAL
INSTRUCTION MANUAL Before commencing assembly, please read these instructions thoroughly. Specifications Wing Span: 50 in / 170 mm Wing Area: 484 sq in / 31. sq dm Flying Weight: 3.5 lbs / 1600 g Fuselage
More informationInstruction Manual book
Instruction Manual book ITEM CODE BH53. SPECIFICATION Wingspan : 1,250mm 49.21 in. Length : 930mm 36.61in. Weight : 1.1kg 2.42 Lbs. Parts listing required (not included). Battery: 3 CELLS-LI-POLY-11.1V-2,500
More informationINSTRUCTION MANUAL. Specifications. Wing Area Flying Weight Fuselage Length. 28 oz / 800 g 30.0 in / 760 mm
ALMOST-READY-TO-FLY INSTRUCTION MANUAL Requires : -channel radio w/ micro servos, Outrunner Motor w/ Propeller Adaptor 0A Brushless ESC, 3 cells 11.1V 100 mah Li - Po battery & charger. Wing Span Wing
More informationSkymaster ARF F-18E Instructions Manual
Skymaster ARF F-18E Instructions Manual first: Take out the front servos mount, install front fuel tank before installing nose cone connect nose cone to fuselage by 6 screw Take out the 6 screws and Bottom
More informationMECOA EZ-4061 Trainer
MECOA EZ-4061 Trainer EZ-4061 is a newly designed, Almost Ready to Fly kit. It is an extremely easy to control trainer with strong construction and excellent aerodynamic performance. This is a great choice
More informationTIGER MOTH 120 ASSEMBLY INSTRUCTIONS
TIGER MOTH 120 ASSEMBLY INSTRUCTIONS SPECIFICATIONS Wing Span: Length: Radio: Flying Weight: 1920mm 1580mm 4 channel with 6 servos 4200g AILERON ASSEMBLY 1 Start by removing the servo cover from the bottom
More informationCorvus Racer CC
Corvus Racer 540 35CC Item No:L-G035008 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio mm mm 1200sq in (77.4sqdm) 9.9-12lbs(4.5-5.5kg) 91-1.20(2C) 1.10-1.40(4C) 20-40cc
More informationFUSELAGE CONSTRUCTION
FUSELAGE CONSTRUCTION Note: prior to building and gluing on the work surface use protective covering on your building surface. (wax paper or clear wrap) Fit the laser cut Fuselage Front and Fuselage Rear
More informationCitabria Pro. Aerobatic Parkflyer. by Joel Dirnberger
Citabria Pro Aerobatic Parkflyer by Joel Dirnberger Revision C: December 21, 2004 Citabria Pro Building Instructions Length: Wingspan: Wing Area: Flying Weight: Wing Loading: Functions: Specifications:
More information30% Edge 540T Almost Ready to Fly
Lanier R/C 30% Edge 540T Almost Ready to Fly WARNING! THIS IS NOT A TOY! THIS IS NOT A BEGINNERS AIRPLANE This R/C kit and the model you will build from it is not a toy! It is capable of serious bodily
More informationLANDING GEAR. 1. Fit landing gear into slots on bottom of fuselage.
LANDING GEAR 1. Fit landing gear into slots on bottom of fuselage. 4. Use channel-lock pliers to press blind nuts into position (note: drilled hole should be slightly smaller than shaft of blind nut for
More informationEXTRA 330SC 60CC. Item No:H G Specifications cc gas DA50,DA60, DLE55, DLE60(twin), 3W55. Description
EXTRA 330SC 60CC Item No:H G060011 Specifications Wing Span Length Wing Area Flying Weight Gasoline Radio Description Carbon Fibre : 92" (2347mm) 84 1/2 " (2060mm) 1526.8 sq in(98.5sq dm) 16 17lbs(7300
More informationAT channel 6 servos
Wing Span: Wing Area: Fuselage Length: Flying weight: Power system: Radio: 60.7in/1540mm 561 sq in/36.3 sq dm 44.1in/1120mm 6.9 Ibs/ 3100g 46(2C0/71(4C) 5 channel 6 servos AT6-46 INSTALLING AILERONS Begin
More informationMXS R 30CC. Item No:L G Specifications. 67 1/2"(1720mm) (2C) (4C) 26 35cc gas DLE 30/35RA MLD35 JC30Evo.
MXS R 30CC Item No:L G030008 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio Description Covering Material Carbon Fibre : 75"(1915mm) 67 1/2"(1720mm) 1023sq in(66sq
More informationInstruction Manual. Specification:
Instruction Manual H I G Specification: Wingspan: 133 cm (52.3 inches) Length : 104 cm (40.9 inches) Weight : 1830gr Engine : 25-32 two stroke Radio : 4 channel - 4 servo H W I N G KIT CONTENTS: We have
More informationEdge 540 V3 35CC. Scheme A. Item No:L G Specifications. Flying Weight
Edge 540 V3 35CC Item No:L G035016 Specifications Wing Span Length Wing Area Flying Weight Glow Gasoline Electric Radio Description 76 (1930mm) 74 (1879mm) 1200sq in(77.4sqdm) 9.9 12lbs(4.5 5.5kg) 91 1.20(2C)
More informationC-180 Builder s Manual
C-180 Builder s Manual. May 20, 2002 Last revised July 11, 2002 Copyright! 2002 Douglas Binder, Mountain Models www.mountainmodels.com sales@mountainmodels.com (719) 630-3186 1 Required Equipment! Xacto
More informationINSTRUCTION MANUAL BOOK.
INSTRUCTION MANUAL BOOK. SPECIFICATION Wingspan : 164 cm 64.57in. Length : 135 cm 53.15 in. Weight : 3.3kg 7.26 lbs. Servo : 7 servos. Radio : 4 channels. Engine : 61 cu.in-2 stroke. 91 cu.in-4 stroke.
More informationBOOMERANG TORUS. Aerobatic Sport Jet for 20 to 34 lbs (P80 to P160) thrust turbines.
BOOMERANG TORUS Aerobatic Sport Jet for 20 to 3 lbs (P80 to P160) thrust turbines. Specifications: Span... 83" (2209mm.) Span with Wingtip Tanks 90" (2286mm.) Length...87" (2108mm.) Weight 29 Lbs.(13.15
More informationRESolution V2 Manual
RESolution V2 Manual Note for the German Manual: Yellow Bottle thick CA Pink Bottle Med CA Blue tube 5 minute Epoxy Green tube 90 Minute Epoxy Construction of the Fuselage Step 1: Cover the plan with a
More informationRYAN STA SAFETY PRECAUTIONS. "Sport Scale E-Power ARF" For Intermediate and Advanced Fliers. This radio control model is not a toy!
RYAN STA "Sport Scale E-Power ARF" For Intermediate and Advanced Fliers. SAFETY PRECAUTIONS This radio control model is not a toy! First-time builders should seek advice from people with model building
More information1/6 PA-25 PAWNEE. *Specifications are subject to change without notice.*
1/6 PA-25 PAWNEE INSTRUCTION MANUAL [ A335 Kit ] Wing Span : 72 in / 1830 mm Wing Area : 736 sq in / 47.5 sq dm Flying Weight : 6.6 lbs / 3000 g Fuselage Length : 48 in / 1220 mm Requires : "Glow Power"
More informationExtra 330LT CC. 2 Colour schemes H-G120001A ORACOVER FERRARI RED # ORACOVER WITH # ORACOVER BLACK # ORACOVER SILVER #
Extra 330LT 85-125CC Item No:A-G120001 Specs: WING SPAN: LENGTH: WING AREA: FLYING WEIGHT: ENGINE: RADIO: Description Covering Material Carbon Fibre: 111 (2833mm) 100" (2530mm) 2139sq in (138sq dm) 25.3-28lbs
More informationFUJI FA-200 AERO SUBARU
FUJI FA-200 AERO SUBARU SEMI SCALE SPORT MODEL AERO SUBARU Assembly and Operations Manual Please review this manual throughly Before assembling or Operating The AERO SUBARU Semi scale sport model We ve
More informationCorvus Racer Colour schemes. AeroPlus RC Copyright 2013 All Rights Reserved
Corvus Racer 540 59 Item No:A E050003 Specifications WING SPAN: 59"(1500mm) LENGTH: 54.1"(1374mm) WING AREA: 654sq.in.(42.2sq.dm.) FLYING WEIGHT: 4.6 5.3lbs(2000 2300g) Electric:Brushless outrunner 8Oz.
More informationInstruction Manual. Item No: AL001
Instruction Manual Item No: AL001 Specifications: Wingspan: 2037mm (80.2 in) Length: 1677mm (66 in) Wing Area: 65.5dm2 (1015.3 sq in) Flying Weight: 7.6kg (16.7 lbs) Engine(not incl.): 45-50cc Gas Radio(not
More informationRADIO CONTROL MODEL / RC FLUGMODELL INSTRUCTION MANUAL
RADIO CONTROL MODEL / RC FLUGMODELL INSTRUCTION MANUAL SPECIFITIONS Wingspan...57.5 in. / 146cm Length...50 in. / 127cm Engine...46 2T /.70 4T or Electric equivalent. Radio...4 ~ 6 channel Almost ready
More informationPERCIVAL P-56 PROVOST
Instruction Manual Book. PERCIVAL P-56 PROVOST OLEO STRUTS LANDING GEAR. ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER Glow and EP 95% ALMOST READY TO FLY SPECIFICATION: - Wingspan: 1,644mm
More informationTWEETY 25 INSTRUCTION MANUAL. Almost Ready to Fly Nitro/Electric Aerobat FEATURES SPECIFICATIONS
TWEETY 25 Almost Ready to Fly Nitro/Electric Aerobat INSTRUCTION MANUAL SPECIFICATIONS FEATURES WINGSPAN: 45.7 (1160mm) LENGTH: 38.6 (980mm) WING AREA: 370 sq in(24 sq dm) FLYING WEIGHT: Approx. 3.3 lbs
More information96 WING SPAN SPITFIRE (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED
96 WING SPAN SPITFIRE (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED GENERAL INSTRUCTIONS Should you elect to use the recommended Door Skin, which is 1/8 mahogany plywood measuring 36 x 88. Have it cut
More informationBashing The Hanger 9 Cessna 182 ARF Part 4
Bashing The Hanger 9 Cessna 182 ARF Part 4 Eric Helms Pongo Air This is the final installment of a four-part article covering a variety of modifications incorporated into a Hanger 9 Cessna 182 ARF. Upgrades
More informationVIPER 140 Manual. Release 1.0 January 2018
VIPER 140 Manual Release 1.0 January 2018 Please read this user manual carefully, it contains instructions for the correct assembly of the model. Please refer to the web site www.harlock-rc.com for updates
More informationF3A -70E ASSEMBLY MANUAL
F3A -70E ASSEMBLY MANUAL The new F3A-70E, was designed in an extremely lightweight structure, the all wood airframe, and the new revolutionary Lift Generator on landing gear give the F3A-70E an impressive
More informationFAIREY ALBACORE. Instruction Manual Book. Glow and EP. Item code: BH % ALMOST READY TO FLY SPECIFICATION:
Instruction Manual Book. FAIREY ALBACORE ALL BALSA - PLY WOOD CONSTRUCTION. COVERED IN A HEAT-SHRINK FILM WITH PRINTED. Glow and EP 95% ALMOST READY TO FLY SPECIFICATION: - Wingspan: 1,693mm (66.65in).
More informationE-AERO EPP PITTS KIT From BP HOBBIES. Parts Included in kit
E-AERO EPP PITTS KIT From BP HOBBIES Parts Included in kit Thank you for purchasing the BP Hobbies/E-aero EPP Pitts. Please take the time to read through the instruction manual before beginning the build.
More informationHIGH-END TECHNOLOGY. Electric ducted fan Starfighter
HIGH-END TECHNOLOGY RC Electric ducted fan Starfighter First we want to thank and congratulate you with your decision in buying one of our Kits. The Starfighter puts together very easily so there is not
More informationHigh performance 90mm fiberglass jet
High performance 90mm fiberglass jet Assembly manual For intermediate and advanced fliers only! Specs Wingspan: 1255mm Fuselage length: 1250mm Flying weight: 2600-3000g Wing area: 22.6 dm² Wing loading:
More informationPROCTOR. Instruction Manual Book 95% ALMOST READY TO FLY. Item code: BH154. SPECIFICATION ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER
Instruction Manual Book PROCTOR Item code: BH154. ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER 95% ALMOST READY TO FLY SPECIFICATION Wingspan: 1,360 mm (53.54 in). Length: 1,480 mm(58.27 in).
More information90 WING SPAN P-51D MUSTANG (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED
90 WING SPAN P-51D MUSTANG (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED GENERAL INSTRUCTIONS This design is basically an enlargement of the very popular fun scale Mustang 60 Size. You can build it light
More informationInstruction Manual book
Instruction Manual book ITEM CODE: BH50. SPECIFICATION Wingspan : 1,600 mm 62.99 in. Length : 1,230 mm 48.43 in. Weight : 2.5 kg 5.5 Lbs. Radio : 06 channels. Servo : 07 servos. Electric Motor : ( 02pcs
More informationAviator Trainer40 ARF Instruction Manual Specifications
Aviator Trainer40 ARF Instruction Manual Specifications Wingspan: 65.0 in (1650 mm) Length: 53.1 in (1350 mm) Wing Area: 729sq in (47.0 sq dm) Flying Weight: 5.3 lbs (2400g) Dear Customer, Congratulations
More informationJUNKERS JU87- B2 STUKA
Instruction Manual Book Item code: BH169. JUNKERS JU87- B2 STUKA OLEO STRUTS LANDING GEAR. ALL BALSA - PLY WOOD CONSTRUCTION. COVERED IN A HEAT-SHRINK FILM WITH PRINTED. 95% ALMOST READY TO FLY SPECIFICATION:
More informationAssembly Instructions. Stinger 120. Almost Ready to Fly
Stinger 120 Almost Ready to Fly Important Information: Please inspect the plane before beginning to assemble to make sure you are happy with it. After assembly has begun you cannot return the kit. If you
More informationDORNIER DO 27 SEMI SCALE SPORT MODEL DORNIER DO 27. Please review this manual throughly Before Assembling or Operating The DORNIER DO 27
DORNIER DO 27 SEMI SCALE SPORT MODEL DORNIER DO 27 Assembly and Operations Manual Please review this manual throughly Before Assembling or Operating The DORNIER DO 27 Semi Scale Sport Model We ve used
More informationTHE APOGEE A 100-INCH AMA DURATION SAILPLANE FROM DYNAFLITE
THE APOGEE A 100-INCH AMA DURATION SAILPLANE FROM DYNAFLITE Apogee is the intermediate sailplane designed to be competitive in AMA duration contests. Effective spoilers, rudder and full flying stabilizer
More informationBUCKER BU 131 JUNGMANN ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER
Instruction Manual Book. BUCKER BU 131 JUNGMANN ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER Glow and EP 95% ALMOST READY TO FLY SPECIFICATION: - Wingspan: 1,850 mm (72.83 in). Length: 1,660
More informationHIGH-END TECHNOLOGY. Electric ducted fan rafale
HIGH-END TECHNOLOGY RC Electric ducted fan rafale First we want to thank and congratulate you with your decision in buying one of our Kits. The Rafale puts together very easily so there is not much explanation
More informationSPUNKY ASSEMBLY MANUAL
SPUNKY ASSEMBLY MANUAL Please read the tips section at the back of this manual regarding the use of laser cut parts. The proper removal and preparation of these parts is important. When laser cut, some
More informationDORNIER DO 27 SEMI SCALE SPORT MODEL DORNIER DO 27. Assembly and Operations Manual
DORNIER DO 27 SEMI SCALE SPORT MODEL DORNIER DO 27 Assembly and Operations Manual Please review this manual throughly Before assembling or Operating The DORNIER DO 27 Semi scale sport model We ve used
More informationSuper Sky Surfer 2000 Assembly Instructions
Super Sky Surfer 2000 Assembly Instructions Note: Plug and Play version of the Sky Surfer comes with fuselage pre-glued and motor/servos installed. If you wish to route antennas or wires through the tail,
More informationPURE PLEASURE for YOU
1 GRAPHITE 2. Assembling gide PURE PLEASURE for YOU Technical support: VLADIMIR'S Model http://airplane-model.com e-mail: order@airplane-model.com Technical data: Wing span: 3100 mm Wing area: 64.5 dm
More informationPITTS S2S CONSTRUCTION
PITTS S2S CONSTRUCTION FUSELAGE CONSTRUCTION 1) Place the right fuselage side over the plan and mark the former positions. Place the left side over the right side and mark the former positions. Glue F1
More informationBUILDING THE A6M2 ZERO
BUILDING THE A6M2 ZERO Product Support (Do Not Remove From Department) TOP FLITE MODELS, INC CONGRATULATIONS' You now own the most accurate R/C Stand-Off Scale kit ever produced We at Top Flite hope that
More informationLANIER - Giles % - INSTRUCTIONS
Additional Parts Required (4) or more channel radio with 4 servos..25 -.36 two stroke or.40 -.52 four stroke engine Appropriate Master Airscrew prop and Hayes mount for your engine. 2-1/2 Tru-Turn spinner
More informationMUSTANG P-51. Hand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL
MUSTANG P-51 Hand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL Specifications Wingspan---------------------------------------- 60.5 in----------------------- 153.7cm. Wing area-------------------------------------
More informationLANIER - Double Trouble - INSTRUCTIONS. Tail 1 T1 ¼ Balsa 1 T2 ¼ Balsa 2 T3 ¼ Balsa 1 T4 ¼ Balsa 1 T5 ¼ Balsa 1 T6 ¼ Balsa 2 J1 ¼ Balsa 2 J2 Lite ply
Tail 1 T1 ¼ Balsa 1 T2 ¼ Balsa 2 T3 ¼ Balsa 1 T4 ¼ Balsa 1 T5 ¼ Balsa 1 T6 ¼ Balsa 2 J1 ¼ Balsa 2 J2 Lite ply Other Parts 2 Aluminum Gear 1 3/32 Music wire tail skid 2 Elevator and J-plane joiner wire
More informationFOKKER D.VII 1:7.4. No.EP-46K. MTH HOBBY PRODUCTS INDUSTRIAL CO., LTD. MTH HOBBY 2015
No.EP-46K FOKKER D.VII 1:7.4 MTH HOBBY PRODUCTS INDUSTRIAL CO., LTD. www.mth.com.tw mthhobby@mth.com.tw MTH HOBBY 2015 SPECIFICATION: Wing span: 1200mm Wing area: 41 dm Length: 990mm Weight: 1400g, including
More informationDesigned in 2005 by Bernard Burton. Assembly manual Bernard Burton DRAFT 1
Designed in 2005 by Bernard Burton Assembly manual 2005 - Bernard Burton DRAFT 1 The plans can be requested via this link http://www.gundersonaerodesign.com/m12plansreq.htm The laser kit is available here
More informationHAWKER HURRICANE. Instruction Manual Book 95% ALMOST READY TO FLY. Item code: BH147. SPECIFICATION
Instruction Manual Book Item code: BH147. HAWKER HURRICANE ALL BALSA - PLY WOOD CONSTRUCTION. COVERED IN A HEAT-SHRINK FILM WITH PRINTED. 95% ALMOST READY TO FLY SPECIFICATION Wingspan: 1,520 mm (59.84
More informationLANIER - Ultimate Pitts - INSTRUCTIONS. Additional Parts Required. (12) 4-40 blind nuts (Dubro #606)
Additional Parts Required (4) or more channel radio with 7-8 servos..91-2.2 two stroke or 1.20-1.84 four stroke engine Appropriate Master Airscrew prop and Hayes mount for your engine. 3 Tru-Turn spinner
More informationHand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL
Hand-made Almost Ready to Fly R/C Model Aircraft ASSEMBLY MANUAL Specifications Wingspan -----------------------.148 cm--------------- 58.3 in. Wing area ----------------------- 3474sq. cm ---- 538.4sq
More informationASSEMBLY & OPERATIONS MANUAL
TM TM AERO SUBARU 40-52 ARF ECS SEMI SCALE MODEL WITH POLYCOTE ECS ENHANCED GRAPHICS SYSTEM #VMA-S140B (blue as shown) #VMA-S140R (red) This model may be produced in a number of different graphic schemes
More informationLANIER Dominator INSTRUCTIONS
ADDITIONAL EQUIPMENT NEEDED TO COMPLETE YOUR DOMINATOR 500 General 3.2 to 4.2 Size two stroke R/C engine, muffler, and engine mount Gas or glow fuel line Minimum of 4 channel radio set required (4-5) 70
More informationElevator Rudder Airbrake Aero-tow release (optional) Throttle (electric version)
Building Instructions Fauvel AV-361 RC glider Order No. 1363/00 Specification: Wingspan: Length: Wing area: Weight, glider: Wing loading: Weight, electric glider: Wing loading: RC functions: Recommended
More informationVelocity Slingjet. Specifications: Construction Span Length Take-off weight w/ gear. Balsa/foam/film 1055m m (41.54 ) 1040m m (40.
Velocity Slingjet Specifications: Construction Span Length Take-off weight w/ gear Recommended servos w/o nose-steering Recommended fan Recommended motor Recommended controller Balsa/foam/film 1055m m
More informationSZD-10 bis CZAPLA ASSEMBLY MANUAL IN PICTURES
1 RUDDER Plan and parts: 2 Assembly steps: Photo above: glue together rudder spar, ribs and trailing edge. Clamp spar to a flat surface (chipboard on the photo) and make sure the straight aligment of the
More informationBuilding instructions. Grob G 109. RC motor-glider Order No. 1340/00. Specification: approx mm. RC functions:
Building instructions Grob G 109 RC motor-glider Order No. 1340/00 Specification: Wingspan Length Wing area Tailplane area Total surface area All-up weight with 12 cells Wing loading (wing only) approx.
More informationNOORDUYN NORSEMAN. Instruction Manual Book 95% ALMOST READY TO FLY. Item code: BH157. SPECIFICATION
Instruction Manual Book Item code: BH157. NOORDUYN NORSEMAN ALL BALSA - PLY WOOD CONSTRUCTION. COVERED WITH ORACOVER. 95% ALMOST READY TO FLY SPECIFICATION - Wingspan: 1840 mm (72.44 in). - Length: 1180
More information94 Yak 54 ARF WARNING
94 Yak 54 ARF WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that could be dangerous.
More informationPiper Cherokee /3 scale. Construction Manual
Piper Cherokee 140 1/3 scale Construction Manual STAB CONSTRUCTION 1. Remove foam cores from cradle and place on flat surface. Inspect pieces before you epoxy halves together making sure leading and trailing
More informationINCLUDED IN THIS KIT: SPECIFICATION: NEEDED BUILDING TOOLS: REQUIRED EQUIPMENT:
Please review this entire manual before beginning assembly. By doing so it will help you better understand each step as you progress in the actual building of your kit, and you will do a better job in
More informationHot Stik ARF WARNING. Copyright 2005 Carl Goldberg Products LTD CARL GOLDBERG PRODUCTS, LTD.
Hot Stik ARF INSTRUCTIONS WARNING A radio-controlled model is not a toy and is not intended for persons under 16 years old. Keep this kit out of the reach of younger children, as it contains parts that
More informationR/C Scale Model Instructions
Vickers 151 Jockey 32.6 Vickers 151 Jockey 32.6 1/12 Scale R/C Scale Model Instructions CONTACT INFORMATION Designed by M.K. Bengtson Prototype by Bert Ayers Manufactured and Distributed by: Bengtson Company
More information