Tank wall mount kit LZX

Size: px

Start display at page:

Download "Tank wall mount kit LZX"

Justin Lawrence
6 years ago
Views:

1 DOC Jul07 Tank wall mount kit LZX Instruction Sheet Edition 1 July 2007 wc/kt

3 Instruction Sheet Tank wall mount kit LZX DOC Jul07 Introduction This instruction sheet describes how to install tank wall mount kit LZX Items supplied with LZX Items supplied with the tank wall mount kit are shown in Figure 1 on page 1. Figure 2 on page 2 shows the dimensions of the mount kit components. Installation dimensions are shown in Figure 3 on page 3. Figure1Itemssuppliedwith the tank wall mount kit 1 1 Mount pipe (2 m) (Cat. No. BRO075) 13 Washer (4x) 2 Tank wall mount for SONATAX sc (Cat. No. LZY370) 14 Quick-fit anchor (4x) 3 Base (Cat. No. ATS012) 15 Plug (Cat. No. LZX909) 4 Fastening lug 16 Set of cap screws (Cat. No. LZY429) 5 Pipe bracket (Cat. No. LZY449) (2x) 17 Cap screw M8 x 30 mm (4x) 6 Bracket, threaded 18 Washer for M8 (4x) 7 Bracket, unthreaded 19 Set of cap screws (Cat. No. LZY362) 8 Set of cap screws (Cat. No. LZY445) 20 Cap screw M5 x 12 mm (7x) 9 Cap screw M5 x 20 mm (3x) 21 Spring washer for M5 (7x) 10 Washer for M5 (3x) 22 Hex wrench 4 mm 11 Set of quick-fit anchors (Cat. No. LZY428) 23 Sealing plug (Cat. No. LZX908) 12 Nut M8 (4x) 24 O-ring for SONATAX sc (Cat. No. LZY453) 1 Items supplied are subject to change without notice. 1

4 Figure 2 Dimensions 2

Figure 3 Installation dimensions Select the install location Important Note: When installing the SONATAX sc, observe all hazard and safety instructions, particularly the information on selecting the

5 Figure 3 Installation dimensions Select the install location Important Note: When installing the SONATAX sc, observe all hazard and safety instructions, particularly the information on selecting the measuring location and instrument setup in the SONATAX sc user manual. Note: When selecting the install location, always make sure there is safe access to all parts of the system and that the SONATAX sc can never hit the tank wall. During the selection of the install location, pay attention to: The load bearing capacity and strength of the tank wall (lever forces due to flow and installation) The maximum cable and tubing lengths Note: Refer to the SONATAX sc user manual for operating instructions. 3

6 Install the tank wall mount 1. Find a suitable installation location and install the quick-fit anchors. Note: Drill accurate holes so that the fastening lug is exactly vertical. a. Drill the holes (see Figure 4 on page 5) and insert the quick-fit anchors. b. Hit the head of the quick-fit anchor with a hammer to make the quick-fit anchor spread in the hole. Note: Only tighten the nuts after the base and fastening lug have been assembled and aligned. 2. Attach the base to the quick-fit anchors using four M8 nuts and washers (see Figure 5 on page 5). Tighten the nuts by hand. 3. Attach the fastening lug to the base using four cap screws (M8 x 30 mm) and washers (see Figure 6 on page 6). 4. Align base and fastening lug vertically and tighten all screws. Note: If the wall is not exactly vertical, place shims behind the base at the top or bottom and then tighten. If the fastening lug is not vertical, move the base and the fastening lug a few degrees in the holes. 5. Loosely bolt the threaded brackets using cap screws (M5 x 20 mm) and spring washers for M5 to the unthreaded brackets on the mount pipe (see Figure 7 on page 6). During this process pay attention to the installation dimensions (see Figure 3 on page 3). CAUTION Risk of injury. Tighten the screws sufficiently so that the brackets cannot slide off the mount pipe. 6. Based on the local conditions and the immersion depth required (see operating instructions for SONATAX sc) determine the installation position for the two top brackets and slide the mount pipe with the brackets installed on the fastening lug. Note: The flange on the mount pipe should be approximately 3 5 cm under the surface of the water so that the sensor always remains immersed while measurements are made. 7. Check the dimensions and tighten all screws. 8. To attach the sensor, remove the mount pipe from the fastening lug (see Attach the SONATAX sc on page 7). 4

7 Figure 4 Install the quick-fit anchors Figure 5 Attach the base 1 Nut M8 3 Base 2 Washer for M8 4 Quick-fit anchor 5

8 Figure 6 Attach the fastening lug 1 Cap screw M8 x 30 mm 4 Quick-fit anchor 2 Washer 5 Base 3 Fastening lug Figure 7 Attach the mount pipe with the brackets 1 Threaded bracket 3 Unthreaded bracket 2 Mount pipe 6

9 Attach the SONATAX sc 1. Slide the O-ring over the sensor cable. 2. Slide the sensor cable through the mount pipe from below and bolt the pipe flange to the sensor using the cap screws (M5 x 12 mm) and the spring washers for M5 (see Figure 8 on page 7). 3. Insert a plug and a sealing plug in the top of the mount pipe. If necessary, shorten the pipe and then insert the plugs. Figure 8 Attach the SONATAX sc 1 Sealing plug 5 Cap screw M5 x 12 mm 2 Plug 6 Washer 3 Sensor cable 7 O-ring 4 Mount pipe 8 SONATAX sc 7

10 Attach sensor assembly to mount 1. Slide the two brackets (attached to mount pipe and sensor) over the fastening lug and align all the parts, taking into account the installation dimensions and the local conditions (Figure 9 on page 8). Check the position of the sensor in the tank and tighten all screws. 2. Route the sensor cable to the controller and attach the quick-connect fitting. 3. Continue as described in the operating instructions for the SONATAX sc and the controller. Figure 9 Tank wall mount assembled (without sensor) 8

11 Replacement parts and accessories Description Quantity Cat. No. Base 1 ATS012 Bracket for pipes 1 LZY449 Mount pipe (2 m) 1 BRO075 Plug 1 LZX909 O-ring 1 LZY453 Seal plug 1 LZX908 Set of cap screws M5 x 12 mm 1 LZY362 Set of cap screws M5 x 20 mm 1 LZY445 Set of cap screws M8 x 30 mm 1 LZY429 Set of quick-fit anchors 1 LZY428 Tank wall mount for SONATAX sc 1 LZY370 9

12 Contact information HACH Company World Headquarters P.O. Box 389 Loveland, Colorado U.S.A. Tel (800) 227-HACH (800) (U.S.A. only) Fax (970) Repair Service in the United States: HACH Company Ames Service 100 Dayton Avenue Ames, Iowa Tel (800) (U.S.A. only) Fax (515) Repair Service in Canada: Hach Sales & Service Canada Ltd Border Street, Unit 34 Winnipeg, Manitoba R3H 0X4 Tel (800) (Canada only) Tel (204) Fax (204) Repair Service in Latin America, the Caribbean, the Far East, Indian Subcontinent, Africa, Europe, or the Middle East: Hach Company World Headquarters, P.O. Box 389 Loveland, Colorado, U.S.A. Tel +001 (970) Fax +001 (970) HACH LANGE GMBH Willstätterstraße 11 D Düsseldorf Tel. +49 (0) Fax +49 (0) HACH LANGE LTD Pacific Way Salford GB-Manchester, M50 1DL Tel. +44 (0) Fax +44 (0) HACH LANGE LTD Unit 1, Chestnut Road Western Industrial Estate IRL-Dublin 12 Tel. +353(0) Fax +353(0) info@hach-lange.ie DR. BRUNO LANGE GES. MBH Industriestraße 12 A-3200 Obergrafendorf Tel. +43 (0) Fax +43 (0) info@hach-lange.at DR. BRUNO LANGE AG Juchstrasse 1 CH-8604 Hegnau Tel. +41(0) Fax +41(0) info@hach-lange.ch HACH LANGE FRANCE S.A.S. 33, Rue du Ballon F Noisy Le Grand Tél. +33 (0) Fax +33 (0) info@hach-lange.fr HACH LANGE SA Motstraat 54 B-2800 Mechelen Tél. +32 (0) Fax +32 (0) info@hach-lange.be DR. LANGE NEDERLAND B.V. Laan van Westroijen 2a NL-4003 AZ Tiel Tel. +31(0) Fax +31(0) info@hach-lange.nl HACH LANGE APS Åkandevej 21 DK-2700 Brønshøj Tel Fax info@hach-lange.dk HACH LANGE AB Vinthundsvägen 159A SE Sköndal Tel. +46 (0) Fax +46 (0) info@hach-lange.se HACH LANGE S.R.L. Via Riccione, 14 I Milano Tel Fax info@hach-lange.it HACH LANGE S.L.U. Edif. Arteaga Centrum C/Larrauri, 1C- 2ª Pl. E Derio/Vizcaya Tel Fax info@hach-lange.es HACH LANGE LDA Av. do Forte nº8 Fracção M P Carnaxide Tel Fax info@hach-lange.pt HACH LANGE SP.ZO.O. ul. Opolska 143 a PL Wrocław Tel. +48 (0) Fax +48 (0) info@hach-lange.pl HACH LANGE S.R.O. Lešanská 2a/1176 CZ Praha 4 Tel Fax info@hach-lange.cz HACH LANGE S.R.O. Roľnícka 21 SK Bratislava Vajnory Tel (0) Fax +421 (0) info@hach-lange.sk HACH LANGE KFT. Hegyalja út H-1016 Budapest Tel. +36 (06) Fax +36 (06) info@hach-lange.hu HACH LANGE S.R.L. Str. Leonida, nr. 13 Sector 2 RO Bucuresti Tel. +40 (0) Fax +40 (0) info@hach-lange.ro HACH LANGE 8, Kr. Sarafov str. BG-1164 Sofia Tel (0) Fax +359 (0) info@hach-lange.bg HACH LANGE SU ANALİZ SİSTEMLERİ LTD.ŞTİ. Hilal Mah. 75. Sokak Arman Plaza No: 9/A TR Çankaya/ANKARA Tel. +90 (0) Fax +90 (0) bilgi@hach-lange.com.tr HACH LANGE D.O.O. Fajfarjeva 15 SI-1230 Domžale Tel (0) Fax +386 (0) info@hach-lange.si ΗΑCH LANGE E.Π.Ε. Αυλίδος 27 GR Αθήνα Τηλ Fax info@hach-lange.gr HACH LANGE E.P.E. 27, Avlidos str GR Athens Tel Fax info@hach-lange.gr