SAN12 ( <00>)

Size: px

Start display at page:

Download "SAN12 ( <00>)"

Ilene Mosley
6 years ago
Views:

1 SAN12 ( <00>) Wood 13mm (1/2 in.) 3mm (1/8 in.) Sanus Systems 2221 Hwy 36 West Saint Paul, MN USA Customer Service Americas: Europe, Middle East, and Africa: europe.sanus@milestone.com Asia Pacific: sanus.ap@milestone.com accents.sanus.com 2010 Milestone AV Technologies, a Duchossois Group Company. All rights reserved. Accents is a Milestone brand. All other brand names or marks are used for identification purposes and are trademarks of their respective owners.

2 Wood stud walls Tools required WARNING: This product contains small items that could be a choking hazard. Do Not Caution / Warning <00>

3 ADJUSTABLE ADJUSTABLE 3.76 ADJUSTABLE mm TEMPERED GLASS <00> 3

4 IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS PLEASE READ ENTIRE MANUAL BEFORE USING THIS PRODUCT The SAN212 is designed to support audio and video accessory equipment; it is NOT designed to support a television. Specifications: Shelf capacity - DO NOT EXCEED: 22.6 kg (50 lbs) CAUTION: CAUTION: Avoid potential personal injuries and property damage! Do not use this product for any purpose not explicitly specified by manufacturer. The wall must be capable of supporting five times the weight of the mount and accessories combined. This product is not designed for use in metal stud walls! If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this product, contact manufacturer Customer Service or call a qualified contractor. Manufacturer is not responsible for damage or injury caused by incorrect assembly or use. Supplied Parts and Hardware. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts! NOTE: Not all hardware included will be used. After unpacking: (S) Remove screw (S) from top locking plate (LP) of column. Lift locking plate (LP) and remove wall plate [02]. (LP) [02] <00>

5 [03] x 2 [04] x 8 [05] x 2 [02] x 1 [06] x 2 x 1 [07] x 4 [08] x 1 [09] x 1 1/4 in. 1/4-20 x 3/8 in. [10] x 4 1/4 in. [11] x 4 1/4 x 2.5 in. in. [12] x 4 [13] x 1 5/32 in. [14] x <00> 5

6 1 CAUTION: Wall Mounting Wood Stud Mounting CAUTION: Improper use could reduce the holding power of the lag bolt. To avoid potential injuries or property damage: Pilot holes MUST be drilled to a depth of 63.5 mm (2.5 in.), using a 3 mm (1/8 in.) diameter drill bit. DO NOT over-tighten the lag bolts [12]. Any material covering the wall must not exceed 16 mm (5/8 in.). Minimum wood stud size: common 2 x 4 in. (nominal 1.5 x 3.5 in.) NOTE: The column can be adjusted on the wall plate [02] to suit your needs. DO NOT mount the top shelf higher than 99 cm (39 in.) above the floor. 63.5mm 2.5 in. 63.5mm 2.5 in. 127mm 5 in. [02] 99cm 39 in <00>

7 13mm (1/2 in.) 3mm (1/8 in.) 1 < 16 mm 1 2 (5/8 in.) Locate stud. Verify the center of the stud with an awl or thin nail or use an edge to edge stud finder. [02] Level the wall plate [02] and mark the hole locations. 3 4 Drill pilot holes as illustrated. Tighten the lag bolts [12] only until the washers [11] are pulled firmly against the wall plate [02]. [12] [11] 63.5mm 2.5 in <00> 7

8 2 1 A B Mount column onto wall mount [02] by aligning the slots of the column's locking bar with the hooks on the wall mount [02]. [02] 2 (S) When the column is pressed onto the wall mount [02], the locking bar will lift slightly (see A) then drop over the hooks of the wall mount (see B). To lock the column in place, press the rear locking bar down and replace top locking screw (S) and tighten. 3 1 [04] mm (1/16 in.) Add shelf rests [04] to [03] shelf brackets [03] by fitting them into notch on edge of shelf brackets [03] and pressing down to secure. Add nut plate [05] to [14] shelf bracket with screws [10] using the 5/32 in. hex key [14]. [10] [05] Leave a gap of 1.5mm (1/16 in.) between the nut plate [05] and the back of the bracket [03]. [03] [05] <00>

9 4 1 Slide shelf brackets [03] with nut plates [05] into the channel of the column. [03] [05] 2 Adjust shelf brackets [03] to desired positions. Using the 5/32 in hex key [14], tighten the screws [10] of the nut plates [03] to lock the shelf brackets [03] into position. [03] [14] [10] 3 [08] 4 Add top [08] and bottom [09] end caps. 1 in. (S) [09] The column may be adjusted vertically with the bottom cap screw (S) using the 1/4 in. hex key [13]. [13] <00> 9

10 5 Slide glass shelves [06] under upper lip of shelf brackets [03] and lay them flat onto the shelf rests [04]. [03] [04] [06] 6 Cables and wiring for appliances can be routed into the side channels of the column and covered with the side caps [07]. [07] [07] Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively, Milestone ), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document <00>

SAN22BB ( <00>)

SAN22BB ( <00>) SAN22BB (6904-002016 ) Wood Concrete Block or Solid 13mm (1/2 in.) 5.5mm (7/32 in.) 10mm (3/8 in.) Sanus Systems 2221 Hwy 36 West Saint Paul, MN 55113 USA Customer Service Americas: 800-359-5520 651-484-7988