Nest Storage Bed in Fabric Designed by Niels Bendtsen
|
|
- Edmund Oliver
- 5 years ago
- Views:
Transcription
1 General Assembly Instructions Assembly requires two people and 1 2 hours. Assemble bed as near as possible to final resting area. Identify all parts and hardware before beginning assembly. Retain packaging until bed is fully assembled to ensure no fittings or components are accidentally discarded. Make sure assembly area is clean and level DESIGN WITHIN REACH STUDIOS 1
2 Exterior Frame Checklist A B Headboard C Side rails G I D Footboard J E F Plastic feet Slipcover (not illustrated) K H A G H Slat decks B I Headboard bar E J Footboard bar D K Leather handle C Exterior Frame Hardware, Drawn Actual Size Short bolt x 3 M8 x 17mm (5 / 8") Medium bolt x 16 M8 x 25mm (1") Allen wrench x 2 Long bolt x 8 M8 x 50mm (2") Nut x 14 Socket wrench x 1 Washer x 16 Extra-long bolt x 4 M8 x 70mm (2.75") Wrench x DESIGN WITHIN REACH STUDIOS 2
3 Interior Frame Checklist L M Center foot Short support bars N O Long support bars P Storage panels N P O M L Interior Frame Hardware, Drawn Full Size Short bolt x 3 Medium bolt x DESIGN WITHIN REACH STUDIOS 3
4 1. Attach side rails to headboard using medium bolts. Be sure plastic caps in corner brackets are facing up. A B Medium bolt x 8 C 2. Attach footboard to side rails using medium bolts. Be sure plastic caps in corner brackets are facing up. B4 D C Medium bolt x DESIGN WITHIN REACH STUDIOS 4
5 3. Turn bed frame assembly on its side. Screw feet into wider cross braces of corner brackets, and tip bed frame assembly back down. WIDER CROSS BRACE OF CORNER BRACKET E E E E DESIGN WITHIN REACH STUDIOS 5
6 4. Open zipper and fit slipcover down slightly over headboard, just enough to hold it in place, then position remaining slipcover loosely along side rails and footboard. 5. Working from footboard, fit slipcover snugly to corners, then remove fabric backing from velcro a little at a time and press into place along top and bottom edges of footboard. Slide slipcover down on headboard completely, then return to fit slipcover over side rails working from footboard to headboard, smoothing and attaching velcro as you go. Close zipper on headboard, and smooth and attach slipcover. F DESIGN WITHIN REACH STUDIOS 6
7 6. Assemble mattress frame by placing slat decks side by side with slats curving downward and flanged edges to the outsides. Secure using extra-long bolts, nuts and washers as shown. Loosely tighten in preparation for final tightening later. G H Nut x 4 Washer x 8 Extra-long bolt x 4 G H Nut x 4 Washer x 8 Extra-long bolt x DESIGN WITHIN REACH STUDIOS 7
8 7. With slats still curving downward, locate and attach headboard bar using long bolts, nuts and washers as shown. Washer x 4 I Nut x 4 Long bolt x 4 I 8. Attach footboard bar and leather handle to mattress frame using long bolts, nuts and washers as shown. Install handle with Design Within Reach facing outward and upside down. Washer x 4 Nut x 4 J 10 K J Long bolt x 4 K DESIGN WITHIN REACH STUDIOS 8
9 9. With headboard bar, footboard bar and handle attached, firmly tighten nuts and bolts holding mattress frame together. 10. Flip mattress frame into position with slats curving upward, then lower into bed frame as shown. Reaching between slats, attach hinge assembly to side rails using medium bolts. Medium bolt x DESIGN WITHIN REACH STUDIOS 9
10 13. With mattress frame raised and held up by assistant, attach pistons to hinge assembly using nuts as shown. Nut x Connect two short support bars to center foot using short bolts. L M M Short bolt x DESIGN WITHIN REACH STUDIOS 10
11 15. Attach short-bar assembly to side rails using medium bolts. L / M Medium bolt x Join two support bars at center foot and secure with short bolt. Attach long support bars to footboard and headboard using medium bolts. N O Short bolt x 1 O N Medium bolt x DESIGN WITHIN REACH STUDIOS 11
12 17. Place storage panels inside, ensuring all sit flat. P P P P Please Note Mattress frame will not stay fully closed until fitted with your mattress DESIGN WITHIN REACH STUDIOS 12
Please keep for future reference. Dimensions (5') Length cm. Width - 160cm Height cm
Sheridan Ottoman bed Assembly Instructions hygena Please keep for future reference 25/942 /659 56/4268 56/9 /7268 57/499 40/422 57/202 8/8846 Dimensions (4') Length - 202.5cm Width - 0cm Height - 84.5cm
More informationO-Sullivan King 4 Poster Bed O-Sullivan Queen 4 Poster Bed Parts and Hardware List
Parts and Hardware List A. Left Headboard Post 1 pc B. Right Headboard Post 1 pc C. Left Footboard Post 1 pc D. Right Footboard Post 1 pc E. Headboard Panel 1 pc F. Footboard Rail 1 pc. Spindles 4 pcs
More informationStrata. urniture. Adriana Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at
1A Watch our assembly videos at www.strataf.com/videos Parts in the Arm Box: Arm - Outside View Arm - Inside View 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached Back Panel
More informationB Footboard 1. C Headboard Foot 2. D Side Rail 2. E Cross Slat 4. G Support Beam 1. H Cross Slat Support Foot 3. I Finial 4. J Adjustable Leveller 3
B Footboard 1 C Headboard Foot 2 D Side Rail 2 E Cross Slat 4 F Cross Slat for Support Beam (with mounting position) 3 G Support Beam 1 H Cross Slat Support Foot 3 I Finial 4 J Adjustable Leveller 3 Page
More informationQueen Wingback Bed King Wingback Bed
Parts and Hardware List A. Side Rails with Attachment Hooks 2 pcs B. Foot Rail 1 pc C. Head Rail 1 pc D. Center Support Slat 1 pc E. Leg Supports 3 pcs F. Support Slats 4 pcs G. Flat Washers 8 pcs H. Lock
More informationL.L.Bean. Wooden Slat Bed
L.L.Bean Wooden Slat Bed Thank you for purchasing our Slat Bed. Assembly of this product requires A Phillips head screwdriver. We have found it helpful to have a second person present in at least one step
More informationRiverside. Oakmont Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 1 pc. 1 pc. 20270 --5/0 Sleigh Headboard 20274 --5/0-6/6 Bed Rails 20273 -- 5/0 Storage Footboard, Panels, Slats Queen
More informationK-Emily Twin Nkl Canopy Bed K-Emily Twin Pink Canopy Bed K-Emily Purple Twin Canopy Bed
Parts and Hardware List A. Headboard 1 pc B. Footboard 1 pc C. Side Rails 2 pcs D. Support Slats 3 pcs E. Leg Supports 3 pcs F. Long Canopy Rails 2 pcs G. Short Canopy Rails 2 pcs H. Long Posts 2 pcs I.
More informationStrata. urniture. Addison Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at
1A Watch our assembly videos at www.strataf.com/videos.html Parts in the Arm Box: Arm - Outside View Arm - Inside View Corbels x 4 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 Back Panel x 1 with
More informationAssembly Aid. One of the packages contains the required bolts, washers and nuts for final assembly
Assembly Aid Open the box and arrange the pieces similar to what you see here. Assembly instructions as well as the list of tools required for assembly are also in the box. One of the packages contains
More informationStrata. urniture. Mission Rim Instructions. Parts in the Arm Box: Parts in the Body Box:
1A Watch our assembly videos at www.strataf.com/videos.html Parts in the Arm Box: Arm - Outside View Arm - Inside View Corbels x 4 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached
More informationL.L.Bean. Platform Bed
L.L.Bean Platform Bed Thank you for purchasing our Platform Bed. Assembly of this product requires a Phillips head and a flat head screwdriver. We have found it helpful to have a second person present
More informationRiverside. Windhaven Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 2 pcs. 4 pcs. 4 pcs. 4 pcs. 2 pcs. 5/0 Queen Storage Bed 50773 -- 5/0 Storage Footboard w/platform Note: The 50773 Storage Footboard can be used with the 50770 Panel Headboard
More informationStrata. urniture Watch our assembly videos at Denali Arms. Parts in the Arm Box: Hardware in this Box:
1A Denali Arms Watch our assembly videos at www.strataf.com/videos.html Parts in the Arm Box: Arm - Outside View Arm - Inside View 1B Hardware in this Box: (80mm) x 8 Barrel Nuts x 8 x 8 Wood Buttons x
More informationVince Ottoman Bed Frame
Vince Ottoman Bed Frame Assembly Instructions - Please keep for future reference 355/4845 330/7281 Dimensions Depth x Width x Height 213cm x 148cm x 111cm (Double) 223cm x 163cm x 111cm (King) Important
More informationCONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013
U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -
More informationRiverside. Harbor Hill Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 2 pcs. 3 pcs. 3 pcs. 4 pcs. 4 pcs. 4 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 2 pcs. 8 pcs. 1 pc. 25770 -- 4/6-5/0 Panel Headboard (NOTE: the 25775 Leather
More informationProduct Information. Brass & Cast Bedsteads
Product Information Brass & Cast Bedsteads parts CheCk list 4 0,4 6,5 0,6 0 slatted FraMe 01 headend 1 02 Footend 1 03 head end extension legs 2 04 side rails 2 05 end cross bar 2 06 Center cross bar 1
More informationRiverside. Harbor Hill King Storage Bed Assembly Instructions
King Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 2 pcs. 6 pcs. 3 pcs. 4 pcs. 4 pcs. 4 pcs. 1 pc. 1 pc. 2 pcs. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 25780 -- 6/0-6/6 Panel Headboard (NOTE: the 25785 Leather Headboard
More informationYardley Single Ottoman Assembly Instructions
Yardley Single Ottoman Assembly Instructions Dimensions mm Double Length Width eight 2040 10 910 eed assistance? Call: 0344 292 0000 elpful advise before you begin: 1. We suggest you spend a short time
More informationPRINCESS SINGLE BED WITH TRUNDLE
PRINCESS SINGLE BED WITH TRUNDLE If you have any questions regarding assembly or if you are missing parts, do not return this item to Sam s Wholesale Club Please call our customer service number and have
More informationRouen Storage Bed. John Lewis PRE-ASSEMBLY PREPARATION. Double King Size. Stock code: 803/44304 Stock code: 803/44305
John Lewis Double King Size Rouen Storage Bed Stock code: 80/4404 Stock code: 80/4405 Thank you for purchasing this Rouen Storage Bed. Please read the instructions carefully before use to ensure safe and
More informationBeadboard Curved Bed Queen Size
Beadboard Curved Bed Queen Size PRE- ASSEMBLY: Remove all parts and hardware from the box, and lay them out on a carpeted or scratch-free work surface. The shipping box provides an ideal work surface,
More informationLEAMINGTON BED (DOUBLE)
LEAMINGTON BED (DOUBLE) ASSEMBLY INSTRUCTIONS. IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY. Tools Needed Helpline If you have any problems with this product or require any replacement fittings
More informationhttps://www.wallbedsbywilding.com/wallbed-installation-studio-series/
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationMyra Bed Room King Storage Bed Assembly Instructions. Hardware and Parts packed with the Headboard. One Left & One Right H-C
email: Headboard Panel info@riverside-furniture.com King Storage Bed Hardware and Parts packed with the Headboard Headboard Post Headboard Stretcher Page 1 of 7 H-A One Left & One Right H-C M5/16"-18 x
More informationFor Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationPRE-ASSEMBLY PREPARATION 1/6. Please ensure instructions are read in full before attempting to assemble this product.
PRE-ASSEMBLY PREPARATION Please ensure instructions are read in full before attempting to assemble this product. Necessary Tools Please check the pack contents before attempting to assemble this product.
More informationMedium HoneyBadger Chase Rack Installation Instructions
PREPARATION Medium HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend reading
More informationThis instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently.
This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. Don t be put off by the size of the instruction manual as the large diagrams
More informationUser Instructions Multiline Otter Scoreboard Caddy Assembly
List of parts: User Instructions Multiline Otter Scoreboard Caddy Assembly Single Caddy Double Caddy 1 1 Base assembly with attached wheels 2 4 1 1 2 4 4 8 10 20 12 Uprights (60 or 74 aluminum extrusion)
More informationKEATING BED. Date: 02-Apr-15 Page 1 of 7 Rev:
KEATING E ate: 02-Apr-5 www.williams-sonoma.com Page of 7 Important Safety Instructions: Please read all instructions carefully before assembling. For your safety, assembly by two or more adults is strongly
More informationINSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationFull Size Bed The Jocelyn
Full Size Bed The Jocelyn www.andrewharriswoodwork.com Page 1 of 14 Introduction This plan makes a bead frame for a full size mattress. Although a full size mattress should be standard size. Please make
More informationStuff-Your-Stuff Platform Bed (Twin and Full)
Stuff-Your-Stuff Platform Bed (Twin and Full) Pre-Assembly: Please read all instructions before beginning assembly. Assembly by two people is a must. Save all packing materials until assembly is complete
More informationBEADBOARD LOFT BED ASSEMBLY INSTRUCTIONS
BEADBOARD LOFT BED ASSEMBLY INSTRCTIONS Date: 2013-Apr.-25 www.pbteen.com Page 1 of 10 ARNING: Failure to follow these warnings and assembly instructions could result in serious injury or death. To prevent
More informationINSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationYardley Double Ottoman Assembly Instructions
Yardley Double Ottoman Assembly nstructions Dimensions mm Double Length Width eight 2040 1480 910 Need assistance? all: 0344 292 0000 elpful advise before you begin: 1. We suggest you spend a short time
More informationGas Lift Bed Assembly Instructions (please retain this instruction for future reference)
Gas Lift Bed Assembly Instructions (please retain this instruction for future reference) To assemble your bed you have been supplied with 12 x 12mm button head bolts, 4 x 15 mm Philips Head Screws, 6 Philips
More informationEmily Storage Bed Stock code king stone: 810/80505 Stock code king mink : 803/46405 Stock code king grey : 803/46507
John Lewis Stock code double mink : 80/46404 Stock code double stone : 80/80504 Stock code double grey : 80/46506 Emily Storage Bed Stock code king stone: 80/80505 Stock code king mink : 80/46405 Stock
More informationPlease Do Not Return Your Item to the Retailer
Please Do Not Return Your Item to the Retailer Thank you for your purchase of an Epic Furnishings item You should enjoy many years of trouble free, dependable use If for any reason you are missing parts,
More informationASSEMBLY INSTRUCTIONS. IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY.
WESTCOTT STORAGE BED ASSEMBLY INSTRUCTIONS. IMPORTANT - RETAIN FOR FUTURE REFERENCE - READ CAREFULLY. Tools Needed Helpline If you have any problems with this product or require any replacement fittings
More informationINSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD
For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationSide Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY
Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationRH-412 STEEL DOORS INSTALLATION INSTRUCTIONS
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.
More informationThe Phoenix. Professional Quilting Frame. Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.
The Phoenix Professional Quilting Frame Copyright January 1, 2016 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.1 1 The Phoenix Professional Quilting Frame Parts List Box 1...3 Box
More informationRoll In W/L Dock PAGE 1
Roll In W/L Dock PAGE 1 1 2 3/8 X 1 CARRIAGE BOLT SS 3/8 FLANGE NUT BRASS 3 4 1/2-13 X 1.25 SQ BOLT SS 1/2 SQ NUT BRASS 5 3/8-16 X 2.5" BOLT SS PAGE 2 6 7 BRACE BRKT SINGLE AXLE TUBE 8 9 3" AXLE WASHER
More informationContinuum Frame Assembly Instructions
Continuum Frame Assembly Instructions Copyright January 1, 2017 Jim M. Bagley, GraceWood, Inc (Reproduction Prohibited) Version 2.2 Table of Contents Continuum Frame Table of Contents... i Warranty...ii
More informationStock Code: 803/44302 King. Stock Code: 803/44303 Super King Stock Code: 803/44301
John Lewis Rouen Bed Double Stock Code: 80/440 King Stock Code: 80/440 Super King Stock Code: 80/440 Thank you for purchasing this Rouen Bed. Please read the instructions carefully before use to ensure
More informationBoris toddler bed. Instruction manual. Important!
Boris toddler bed Instruction manual Important! KEEP FOR FUTURE REFERENCE 1 Thank you for purchasing this Boris toddler bed. Please read the instructions and warnings carefully before use to ensure safe
More informationM10 x 75mm Sockethead Cap Screws. 5mm Fender Washer (12) Included - (8) Required. #10 x 2.5" PH Wood Screws. (30) Included - (24) Required
Door System Unit - Hardware Tools Included: (2) 2mm Allen Wrenches, (2) 3mm Allen Wrenches, (2) 4mm Allen Wrenches, (2) 6mm Allen Wrenches, and (1) 8mm T-Handle Allen Wrench Tools Required: Phillips Screwdriver,
More informationThis manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified.
This manual will aid in the assembly of the FireBall V90 and FireBall X90. The assembly of both machines will be identical, unless specified. Step #1 Lay all parts out to verify quantities. (2) 2 x 25-1/4
More informationBLUE ANT FURNITURE TITLE: FULL BUNKBED INSTRUCTIONS 10/10/09 DWG. NO. INSTR_888-FULL-BUNK SHEET 1 OF 9
BLUE ANT FURNITURE TITLE: FULL BUNKBED INSTRUCTIONS 10/10/09 DWG. NO. INSTR_888-FULL-BUNK SHEET 1 OF 9 WARNING: Failure to follow these warnings and assembly instructions could result in serious injury.
More informationBIFOLD FUTON FRAME TRINITY ARM. Seat Rails and Slats x 1. *Note: Use 4pc of 100mm Bolts and 4pc of 60mm Bolts to attach the arms to the Stretchers.
1A Parts in this box. 2pc with extra holes 2pc with extra holes & plastic stoppers Arms x 2 Back Rails and Slats x 1 Full Size: Slat Supports x 6 3pc are longer for the Back deck Back Side Rails x 2 Seat
More informationWILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS
WILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS With Storage Headboard Installation Booklet 19 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE
More informationPLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING WARRANTY AND USER INFORMATION CAN BE FOUND AT THE END OF THESE INSTRUCTIONS
Thank you for purchasing the SleepSafe Safety Bed. With proper care, your bed will provide years of safe use. Carefully unpack all the contents of your bed and verify that all parts are included using
More informationThe Queen Quilter Professional Quilters Kit Frame
The Queen Quilter Professional Quilters Kit Frame Assembly Instructions Table of Contents: Before you begin......................... Pg. 2 Wood parts............................. Pg. 3 Hardware..............................
More informationFORD RANGER Onwards SLIMLINE II RACK (1255MM x 1358MM)
FORD RANGER - 2012 Onwards SLIMLINE II RACK (1255MM x 1358MM) FAFR001 / KRFM010T INSTALL TIME: 60 mins READ ME FIRST: Thank you for purchasing a Front Runner Slimline II Rack. This Roof Rack consists of
More informationINSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationMia Bed. John Lewis. Double King size PRE-ASSEMBLY PREPARATION. Stock Code: 810/84103 Stock Code: 810/84104
John Lewis Mia Bed ouble King size Stock ode: 80/80 Stock ode: 80/80 Thank you for purchasing this Mia Bed. Please read the instructions carefully before use to ensure safe and satisfactory operation of
More informationWallbeds Northwest ENDURA CABINET PLANS AND INSTRUCTIONS
Thank you for purchasing your Wall Bed from Wallbeds Northwest. If you have purchased a complete "Endura DIY Kit," then much of the work is already done for you. Please skip to assembly instructions. Note
More informationEmily Bed. John Lewis PRE-ASSEMBLY PREPARATION. Mink Grey Stone
John Lewis Mink Grey Stone Emily Bed Stock code: Small ouble - 80/60, ouble - 80/60, King - 80/60 Stock code: Small ouble - 80/60, ouble - 80/60, King - 80/60 Stock code: ouble - 80/800, King - 80/800
More informationInstalling the Profile Privacy Panel. Assemble top mounting bracket. Prerequisites. Tools
Installing the Profile Privacy Panel Complete these instructions to install the Profile Privacy Panel. Privacy panels are available in various heights to match tiers and include mounting hardware for slat
More information3/8-16 x 3/4 cap screw. 3/8-16 hex nut for above screws. 1/4-20 x 3/4 socket cap screw. 3/16 short arm hex key (not to scale)
Super Slab Roller 24, 30 and 36 models Worktable Assembly Directions P.O. Box 89 Cheney, WA 99004 USA 509.235.9200/800.23.7896 Fax: 509.235.9203 www.northstarequipment.com Revised September, 2006. All
More informationAddison Adjustable Headboard Platform Beds DUET finish Assembly Instructions Model #
Addison Adjustable Headboard Platform eds DUET finish Model # 3800DUET Addison Queen Adjustable Headboard Platform ed 3804DUET Addison King Adjustable Headboard Platform ed 3807DUET Addison Cal-King Adjustable
More informationFor additional assistance call
The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or
More informationMOD-5421/5422/5423/5424/5425/5426
Thank you for purchasing the MODWY! Before you start, here is some helpful advice: 1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step instructions.
More informationINSTRUCTION BOOKLET #C20
INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO
More informationLab Style Table Frame Part No Assembly Guide Automation Technology
Ergonomic Workstations Lab Style Table Frame Part No. 8 0 Assembly Guide 7 90 70 Automation Technology SPECIFICATIONS Lab style frame part number... 80 Height... 70 mm (8.") Width... 90 mm (.7") Depth...
More informationPLEASE CHECK ALL BOXES FOR HARDWARE BEFORE DISCARDING
Thank you for purchasing the SleepSafe Safety Bed. With proper care, your bed will provide years of safe use. Carefully unpack all the contents of your bed and verify that all parts are included using
More informationELEVEN COLLABORATIVE. CONFERENCE TOPS Assembly Instructions
ELEVEN COLLABORATIVE Table of Contents SUPPORT BRACE ASSEMBLY.... 3 TABLE BASE FRAME ASSEMBLY.... 4 LEG ATTACHMENT.... 5 TOP JOINING PLATE ASSEMBLY... 6 TOP CLAMP/TOP SPACER INSTALLATION.... 7 TOP PLACEMENT
More informationSleepSafe II Hi Lo (Medium Bed)
SleepSafe II Hi Lo (Medium Bed) Assembly Instructions 3135 Dillons Mill Road Callaway, VA 24067 Toll Free 866.852.2337 Fax 540.334.2100 www.sleepsafebed.com Thank you for purchasing the SleepSafe II Hi
More informationWhalen Furniture Mfg. Inc. Factory No. 4 Page # 1
ADULT ASSEMBLY REQUIRED DUE TO THE PRESENCE OF SMALL PARTS, SHARP POINTS, SHARP EDGES If you have any questions regarding assembly or if you are missing parts, do not return this item to Sam s Wholesale
More informationLoft Bed Safety Warning
Loft Bed Safety Warning * Follow the information on the warnings appearing on the upper bunk end structure and on the carton. Do not remove the warning label from bed. * Always use the recommended size
More informationInstruction Guide 4A90L
Instruction Guide 4A90L Kargo Master Rancho Cordova, CA 95742 800-343-7486 CustomerService@KargoMaster.com DATE: *PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING, INSTALLING, AND USING THIS
More informationRange height adjustable assembly
Table of contents Digital handset operation 3 Height adjustable bench kit 4-5 Cable carrier 6 Ganging tray and ganging rail 7 Height adjustable return frame kit 8 Cable entry pole 9 24 and 30 d worksurfaces
More informationCTTR Tire Rack Required tools
CTTR Tire Rack Required tools Torque wrench, ratchet, 9/16 socket, tape measure, and square edge. ASSEMBLY REQUIREMENTS *Torque all T-bolt nuts to 35-40 foot pounds. Failure to follow the assembly instructions
More informationUNIT SHOULD BE INSTALLED BY 2 OR MORE PERSONS.
ASSEMBLY INSTUCTIONS ITEM NO: I07-412-WB/PEP Queen ails Thank you for purchasing this quality product. Be sure to check all packing material carefully for small parts that may come loose inside the carton
More informationJoiner Kit For Models N388, C450, E402B, E411T, E415H, E440T, E442B, E521T and E522B
Joiner Kit For Models N388, C450, E402B, E411T, E415H, E440T, E442B, E521T and E522B KIT COMPONENTS Part Illustration Description Rear Bracket Front Lower Bracket Front Upper Bracket KIT APPLICATION This
More informationEURO DELUXE INSTALLATION INSTRUCTIONS
WALLBEDS! TM EURO DELUXE INSTALLATION INSTRUCTIONS NOTE: Due to the arched top assembly, the assembly of this model is different from the standard wallbed assembly. PLEASE READ THROUGH THESE INSTRUCTIONS
More information2010 KIDS CENTER #6 K-06
K-06 INSTALLATION GUIDELINES USER GROUP: 2-5 RECOMMENDED CREW: 2 people TOOLS REQUIRED: Tape measure Level High- speed 3/8 electric drill w/clutch NOTE: Use of any other driver may result in damage to
More informationBridgeport All Wood Assembly Instructions STOP! Please read the following important information!
Revision 6/01/2004 Bridgeport All Wood Assembly Instructions STOP! Please read the following important information! For questions on assembly or parts, DO NOT RETURN product to the store. Contact the experts
More informationAll Restoration Hardware bunk beds are designed to meet the highest safety standards and comply with all U.S. and Canadian Bunk Bed regulations.
All Restoration Hardware bunk beds are designed to meet the highest safety standards and comply with all U.S. and Canadian Bunk Bed regulations. Page 1 of 13 Assembly Instructions Callum Storage Twin Bunk
More informationINSTALLATION INSTRUCTIONS RH 412 STEEL DOORS
By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job
More informationCAB END BEDTRAX (SIDE VIEW)
Supplied Hardware: (8-14) 1/4-20 Allen head bolts, (12-18) UHMW mount blocks, (4) D-ring tie downs Tools Needed: Allen head wrench GET TO IT. INSTALLATION INSTRUCTIONS STEP 1. INSERT (2) MOUNT BLOCKS INTO
More informationWellington Wallbed 700 Series Assembly Instructions
Wellington Wallbed 700 Series Assembly Instructions 1. Read all instructions before proceeding. Not following instructions may result in personal harm or damage to the furniture. 2. 2 people are required
More informationBOX-117 E-Z-Go RXV Utility Box Mounting Kit Installation Instructions
BOX-117 E-Z-Go RXV Utility Box Mounting Kit Installation Instructions Contents of BOX-117 Utility Box Mounting Kit: a (1 ea.) Utility Box Support Frame, Driver Side b (1 ea.) Utility Box Support Frame,
More informationMODEL T28173/T28174 ROLLER TABLES INSTRUCTIONS
MODEL T28173/T28174 ROLLER TABLES INSTRUCTIONS FOR MODELS MFD. SINCE 10/17 For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Rails Rollers Reversible
More informationKai Installation Instructions
Kai Installation Instructions Before Beginning Installation Read through the entire instruction thoroughly A minimum of 2 people are required for this assembly These instructions reflect typical assemblies;
More informationWhite Black Espresso Corner Desk Assembly Instructions
White Black Espresso Corner Desk Assembly Instructions Page 1 White / Black / Espresso Corner Desk Parts List Please check packaging for all parts and hardware before discarding. Unpack and lay parts on
More information** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at:
3/01/2007 VISIT THE LITIME WEB SITE: WWW.LITIME.COM ** Do Not Contact the Store ** For Assistance, including missing or broken parts, Call Customer Service at: 1 (800) 225-3865 Double Shed Doors for Back
More informationFORD INTERCEPTOR SEDAN READY BUCKLE
INSTALLATION MANUAL FORD INTERCEPTOR SEDAN READY BUCKLE PART# FT3501RB We recommend you read through the installation guide prior to installation, if you have any questions please call us at 800-516-2322
More informationASSEMBLY INSTRUCTIONS MANUAL
PAGE 1 OF 9 RECOMMENDED TOOLS FOR ASSEMBLY: ALLEN WRENCH (INCLUDED) BOX WRENCH (INCLUDED) PHILLIPS SCREW DRIVER (NOT INCLUDED) PARTS IN CARTON: ALLEN WRENCH SCREWS (20 EACH) ROUND HEAD SCREWS (8 EACH)
More informationTABLE MKI small with Basin and under rack brackets kit
TABLE MKI small with Basin and under rack brackets kit TBRA024 INSTALL TIME: 15 mins IMPORTANT WARNING! IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO
More information======================================================================================== ( DR / DR) JK WRANGLER MOD RACK
(10984 4DR / 10982 2DR) JK WRANGLER MOD RACK INSTALLATION SHEET Important Notes: Some brands of windshield light brackets and snorkels may not be compatible with the 10984 MOD Rack System. Body lifts are
More informationMODEL T1238 MOBILE TOOL TABLE INSTRUCTIONS For Models Mfd. Since 10/17
MODEL T128 MOBILE TOOL TABLE INSTRUCTIONS For Models Mfd. Since 10/17 For questions or help with this product contact Tech Support at (570) 56-966 or techsupport@grizzly.com Introduction The Model T128
More informationBarnwood Bunk Bed Assembly Instructions
Barnwood Bunk Bed Assembly Instructions Parts needed: 1 1 2 1 8 4 10 1 10 16 1 - Tools Needed for Assembly: Cordless Drill with Phillips Head Ratchet w/9/16 socket 9/16 Wrench T-25 Bit Headboard Footboard
More informationStonewood Beds RGB = Rustic Glazed Brown finish Assembly Instructions Model #
Stonewood Beds RGB = Rustic Glazed Brown finish Model # 1716RGBb Stonewood Queen Storage Bed 1726RGBb Stonewood King Storage Bed 1746RGBb Stonewood Queen Bed 1749RGBb Stonewood King Bed Thank you for allowing
More informationor padded area, in the room that it is intended for. Approx assembly time: 30 minutes.
MODWAY HEADBOARD Thank you for purchasing the MOD-5365/5366/5367/5368/5369/5370/537/537/5373/5374/5375/5376/5377/ 5378/5379/5380/538/538/5383/5384/5385/5386/5387/5388/5389/5390/539/539/5393/5394/5395/5396/5397/
More informationJEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 3 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK004 / KRJW016T INSTALL TIME: 2 Hours NOTE: Your Jeep JK (3 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More information