MOD-5421/5422/5423/5424/5425/5426

Transcription

1 Thank you for purchasing the MODWY! Before you start, here is some helpful advice: 1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step instructions. 2.Owing to the size and weight of the bed, we recommend that it is assembled by two adults, on a carpeted or padded area, in the room that it is intended for. pprox assembly time: 45 minutes. 3.Please do not use any tools other than those provided or recommended in these instructions. 4.Please do not throw away any of the packaging or the instruction until you have checked all the components and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe environmentally friendly way. 5.ssemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the components from time to time, so please save the tools that has been provided. 6.Please keep all fitting out of reach of children. Hardware: Bolt M8x20mm x28 B Bolt M8x35mm x12 C Bolt M8x60mm x3 D Spring Washer x8 E lat Washer x8 Nut M8 x6 llen Wrench x1 H Open Wrench x1 Component: Headboard x1 ootboard x1 Side Rail x2 Side Rail x2 Metal Corner x4 Stretcher x1 Center Rail x2 Leg x2 Leg x2 0 Short Support Leg x2 1 Long Support Leg x2 2 Center Support Leg x1 3 Plastic Cover x12 4 Slat x24 Customer Service Page 1 of 6

2 STEP 1: ttach 1 piece of Leg () and 1 piece of Leg () into Headboard () as shown. Secure by using 4 pieces of Bolt (B), 4 pieces of Spring Washer (D) and 4 pieces of lat Washer (E). Use llen Wrench () to tighten Bolts (B) clockwise until secure. Repeat the same steps for ootboard (). E D B E D B Bx8 Dx8 Ex8 x1 STEP 2: ttach 2 pieces of Metal Corner () into Headboard (). Secure by using 4 pieces of Bolt () as shown. Use llen Wrench () to tighten Bolts (), do not fully tighten Bolts () at this step. Repeat the same steps for ootboard (). x8 x1 Customer Service Page 2 of 6

3 STEP 3: Connect 1 piece of Side Rail () and 1 piece of Side Rail () by using 1 piece of Short Support Leg (0) as shown. Secure by using 2 pieces of Bolt (). Use llen Wrench () to tighten Bolts () clockwise until secure. Repeat the same steps for the remaining Side Rail (&) and Short Support Leg (0). 0 x4 x1 STEP 4: ttach 1 piece of assembled Side Rail (&) to Headboard () and ootboard (). Secure through Metal Corner () by using 4 pieces of Bolt () as shown. Use llen Wrench () to tighten Bolts (), do not fully tighten Bolts () at this step. Repeat the same steps for the remaining assembled Side Rail (&). x8 Jx1 Customer Service Page 3 of 6

4 STEP 5: ttach 1 piece of Long Support Leg (1) to 1 piece of Center Rail () as shown. Insert 2 pieces of Bolt (B) through the corresponding holes on Center Rail () to the holes on Long Support Leg (1). Secure by using 2 pieces of Nut (). Use llen Wrench () and Open Wrench (H) to tighten Bolts (B) and Nuts () until secure. Repeat the same steps for the remaining Center Rail () and Long Support Leg (1). B B 1 H Bx4 x4 x1 Hx1 STEP 6: ttach 1 piece of assembled Center Rail () to Headboard (). Secure by using 2 pieces of Bolt () as shown. Use llen Wrench () to tighten Bolts (), do not fully tighten Bolts () at this step. Repeat the same steps for the remaining assembled Center Rail () to ootboard (). x4 x1 Customer Service Page 4 of 6

5 STEP 7: ttach Center Support Leg (1) to each end of Center Rail () as shown. Insert 2 pieces of Bolt (C) from the holes on one side of Center Support Leg (1) through the corresponding holes on each Center Rail ( to the holes on the other side of Center Support Leg (1). Secure by using 2 pieces of Nut (). Use llen Wrench () and Open Wrench (H) to tighten Bolts (C) and Nuts () until secure. H 1 C 1 C 1 2 Cx2 x2 x1 x1 STEP 8: ttach each end of Stretcher () to the assembled Side Rail (&). Secure by using 4 pieces of Bolt () as shown. Use llen Wrench () to tighten Bolts (). Do not fully tighten Bolts () at this step. Inside view of side rail x4 x1 Customer Service Page 5 of 6

6 STEP 9: Insert 1 piece of Bolt (C) through the holes on Stretcher () into the holes on Center Support Leg (2). Use llen Wrench () to tighten Bolts (C), do not fully tighten Bolts (C) at this step. C Cx1 x1 STEP 10: Insert 2 pieces of Slat (4) into 1 piece of Plastic Cover (3) as shown. Insert the other end of the same Slats (4) into the corresponding pre-drilled holes at each Side Rail (&) as shown. Then insert the assembled Plastic Cover (3) into the corresponding holes at Center Rail (). Repeat the same steps for the remaining Slats (4). fter checking all the connections, use llen Wrench () to tighten all Bolts (&B&C) clockwise until secure Pre-drilled holes at Side Rail 4 3 holes at Center Rail ssembly is complete. Your bed is ready to be enjoyed now! x1 Customer Service Page 6 of 6