Wellington Wallbed 700 Series Assembly Instructions
|
|
- Warren Ross
- 5 years ago
- Views:
Transcription
1 Wellington Wallbed 700 Series Assembly Instructions 1. Read all instructions before proceeding. Not following instructions may result in personal harm or damage to the furniture people are required to install the Wallbed and storage units. 3. Attach to the wall the Ready To Assemble (RTA) unit prior to door being hung. 4. For assembly assistance, please call KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. Tools required: -Phillips screwdriver -Power drill -Robertson bits (#1 & #2) -1/8 Drill bit -3/4 Wrench -1/2 Wrench or Ratchet (2 required) -Stud finder (recommended) -Level
2 Top with lights Top back support with 4 holes Headboard rest Back base with 2 holes Lower Front base - Smallest 1. Open sku # (RTA) and place the pieces facing down, leave the gable and top piece face up. 3. Screw in the vertical locking pin into the 7 pre drilled holes on gable's and 4 on the top piece with lights; note the dowel holes are bigger. 2. Install cam locks with arrows pointing out. 4. With a phillips screwdriver, attach top back support to the top piece with lights. The locking pins connect into cam locks; then turn cam lock 1/4 turn to lock it in.
3 5. Flip all your pieces over so the face is up. 6. Attach side gable to the top pieces with lights; lock cams into the top piece. Note that the cam on the top back support, head rest and back base will be locked later when the unit is standing up. 7. Next attach the headboard rest to the side gable 8. Followed by the back base. 9. After that attach the front base and lock the cam with 1/4 turn, do the same steps in reverse order for the other side. 10. With two people lift up the wall-bed unit.
4 11. Now lock the remaining cams in place on the top back support, head rest and back base. 12. With two people you can now move the wallbed to the wall you wish to attach it to. Make sure that there is room remaining beside the wall bed for any additional units. It may be necessary to remove the base board mouldings on the wall. Carefully remove them so they can be cut down to the appropriate size and be replaced when all the cabinetry is in place. 13. level and plume the horizontal case. If the case is not level the door will have gaps and will not close as intended. 14. Use shims to level the base of the unit if necessary. The shims should be trimmed to fit completely underneath the unit. 15. Once is level, use a stud finder and mark the studs out. Pre drill holes using a1/8 drill bit. 16. Then use the provided 3 1/2 screws. To secure the top back support underneath the light and in to the studs in the wall. Then you cover the screw head with the veneer stickers provided.
5 Metal washers Plastic Washers 17. Now open sku # from the packaging and place the bed in front of wall unit. The side that has 3 bolts on it should be facing the wall unit. 18. Next assemble the folding legs with the cross bar using a small washer on a 1/2 screw use a 1/2 wrench to tighten on both sides. 19. Then add one plastic washer to the leg assembly. 19b. Place leg assembly bolt into the bed frame. Add one plastic washer to the bolt on the inside of the bed frame. 20. Then add one metal washer with the large hole on the inside of the frame. 21. Now add the last metal washer with the small hole. Add the nut and use a 1/2 wrench to tighten it down. Do the same on the other side. The leg assembly should move freely; if not loosen the nuts inside the bed frame.
6 1/2 reveal 60 degree angle middle bolt Adjustment nut 2 reveal upper bolt 22. Now move to the wall unit side. Loosen the adjustment nuts on the spring mechanism from a 1/2 to 2 reveal or until unit arms are on a 60 degree angle. You can use your hand or a 3/4 wrench. 23. Take off the middle bolt, it's only hand tightened. Then push the upper most bolt out, on both sides. Don't take this bolt off. upper bolt removed middle bolt lower bolt 24. With two people you can lift the bed assembly on a 60 degree angle and slide the upper most bolt into the groove of the spring mechanisms arm. Then re-attach the middle bolt's using 1/2 wrench or socket. Make sure it's tight then do the same for the top bolt. You can support the bed with your knee during this process, or one person can hold the bed and the other person can tighten the bolts.
7 25. Use a 3/4 wrench to tighten up the spring nut on the spring mechanism, so there is a 1/2 reveal between the arm and the spring plate, again use your knee as a brace. 26. Close the door there will be a reveal on the door gap. Push the bottom over so all gaps are even. The gaps should be even if not the door may not function properly. 27. Then find the studs and pre drill holes on the back base support, and secure it to the wall. 28. You can now put the handles on the bed using the provided 1/2 screws. 29. Load mattress onto frame and attach velcro strap. Using the same 3/4 wrench as before, tighten the adjuster nut on the right and left sides evenly. Check to make sure the frame (with mattress) is leveled both side to side and front to back. Proper leveling will facilitate proper closure and exact sight line of the fit of the face panel to the cabinet. 30. Remove the mattress and place spring covers on spring mechanism.
8 31. There are 6 sticky backed wire management covers provided; use them to run the wires from lights to the corner's and down behind the head board. 32. Once and are together securely, you can install additional units. If you have place it on top of the assembled case and center it carefully. 33. Screw to using the pre drilled pilot holes on the inside of With , and together, begin the installation of and Place the units next to There is no specific arrangement for these two units, they can be placed on either side of the wallbed case. Level and and shim if necessary. 35. Remove the bottom drawers to each of the to each of the units. This is done by pressing on the release clip. Push one up and the other down. 36. Screw (004) to using the screws provided, into the pilot holes above the drawer slides. There should be one pilot hole per unit in this location. Replace the drawers when complete
9 37. Near the top of (004) there are 2 more pilot holes on the inside gable. Put screws in these two locations to secure the units together and have several pilot holes on the gables, use the appropriate holes to screw units together. There are 4 pilot holes to use. 39. Replace mattress and strap it down. Your wallbed is now ready for use. IMPORTANT -Always close the folding leg before closing the Wallbed door. -Turn off the lights in All the cabinets when closing the doors. -The Wallbed MUST be anchored to the wall BEFORE attaching the door and using the bed. Not doing so will lead to furniture damage and personal injury. -The mattress used in the Wallbed must not be more than 12 thick. -Use velcro strap on the bed frame to secure mattress.
INSTRUCTION BOOKLET #34. For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD
For Wallbed models: KING SIZE SIERRA WITH STORAGE HEADBOARD INSTRUCTION BOOKLET #34 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationRequired Tools: Suggested Additional Tools: 1 Cordless Drill with Robertson Bits 1 Ratchet Wrench 1 7/16 or 11mm socket 1 7/16 or 11mm Gear Wrench
Thank you for your recent purchase of a Cabinets by Hayley garage cabinet system. You are about to experience the best made cabinets that you can purchase. Cabinets by Hayley are designed for beauty and
More informationINSTRUCTION BOOKLET #C10 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationhttps://www.wallbedsbywilding.com/wallbed-installation-studio-series/
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationFor Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED
More informationINSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationItem # Thanks for shopping with Improvements!
Thanks for shopping with Improvements! Hampshire -Door Cabinet Item #5505 To order, call -800-64- West Chester, OH 45069 Made in China PR-6 If you have questions regarding this product, call -800-64- Mon.-Fri.
More informationINSTRUCTION BOOKLET #C21. For Wallbed models: KING SIZE
For Wallbed models: KING SIZE INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationINSTRUCTION BOOKLET #C20
INSTRUCTION BOOKLET #C0 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT IN SEVERE PERSONAL INJURY TO
More informationWILDING WALLBEDS INSTALLATION INSTRUCTIONS Bed with storage headboard
WILDING WALLBEDS INSTALLATION INSTRUCTIONS Bed with storage headboard INSTRUCTION BOOKLET #13 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS For Wallbed models: Do-It-Yourself BOOKLET #C90 WARNING! ALL MURPY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION
More informationSide Mount INSTRUCTION BOOKLET #C122 BED STYLE: PARK CITY
Side Mount BED STYLE: PARK CITY INSTRUCTION BOOKLET #C1 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS DURING THE INSTALLATION PROCESS COULD RESULT
More informationLOWLINE SINGLE FOLD DOWN WALL BEDS
ASSEMBLY INSTRUCTIONS LOWLINE SINGLE FOLD DOWN WALL BEDS Tools Required For Assembly No 2 & No 4 Phillips Head Screwdrivers No 2 Slot Head Screwdriver Hammer Electric Drill (Hammer Drill for Masonry) 6.5mm
More informationMount to the Wall INSTALLATION MANUAL
Mount to the Wall 15 Locate the Wooden Studs This step applies to wooden stud wall installation only. Determine and mark the exact locations of two stud centers on the wall. Wooden studs should be spaced
More informationWILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount
WILDING WALLBEDS INSTALLATION INSTRUCTION Side Mount For Wallbed models: Do-It-Yourself Insturction booklet C92 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY. FAILURE TO USE AND FOLLOW THESE
More informationASSEMBLY INSTRUCTIONS DIY WALL BED KIT QUEEN BI FOLD DOOR CABINET & MECHANISM. Tools Required For Assembly. 6.5mm Masonry Drill Bit
ASSEMBLY INSTRUCTIONS DIY WALL BED KIT QUEEN BI FOLD DOOR CABINET & MECHANISM Tools Required For Assembly No 2 & No 4 Phillips Head Screwdrivers No 2 Slot Head Screwdriver Hammer Electric Drill (Hammer
More informationVibe Buffet Assembly Instructions
ssembly Instructions Thank you for your purchase. Please follow the instructions below for correct assembly. bolt bolt locking dowel long x nut x x0 screw x8 x H I J K small screw x4 V W safety strap x
More informationPlans. Easy-to-Build Full-size Deluxe Murphy Bed Plan. For more plans, tools and hardware visit rockler.com
Easy-to-Build Full-size Deluxe Murphy Bed Plan Build a full-size Deluxe Murphy Bed complete with decorative molding and matching side cabinets! Plans For more plans, tools and hardware visit rockler.com
More informationGlideRite Retractable Cover System For Hot Spot Spas (SE & SLX only)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationThis instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently.
This instruction manual is an in-depth look and explanation of how to assemble and install the Murphy Bed properly and efficiently. Don t be put off by the size of the instruction manual as the large diagrams
More informationBarnside Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratch
88 5516 653 Barnside Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have
More informationWILDING WALLBEDS INSTALLATION INSTRUCTIONS Bed with storage headboard
WILDING WALLBEDS INSTALLATION INSTRUCTIONS Bed with storage headboard INSTRUCTION BOOKLET #13 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE INSTRUCTIONS
More informationM10 x 75mm Sockethead Cap Screws. 5mm Fender Washer (12) Included - (8) Required. #10 x 2.5" PH Wood Screws. (30) Included - (24) Required
Door System Unit - Hardware Tools Included: (2) 2mm Allen Wrenches, (2) 3mm Allen Wrenches, (2) 4mm Allen Wrenches, (2) 6mm Allen Wrenches, and (1) 8mm T-Handle Allen Wrench Tools Required: Phillips Screwdriver,
More informationRiverside. Oakmont Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 1 pc. 1 pc. 20270 --5/0 Sleigh Headboard 20274 --5/0-6/6 Bed Rails 20273 -- 5/0 Storage Footboard, Panels, Slats Queen
More informationDisplay-Top Apothecary Cabinet. Assembly Instructions. Page 1
Display-Top Apothecary Cabinet Assembly Instructions Page 1 Display-Top Apothecary Cabinet Parts List Please check packaging for all parts and hardware before discarding. Unpack and lay parts on clean,
More informationWALLBED Assembly Instructions
WALLBED Assembly Instructions 1 Congratulations and a Big Thank You for your purchase of a Wallbed Gallery Murphy Bed! We sincerely appreciate your business! First a few words of advice and caution: 1.
More informationWILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS
WILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS With Storage Headboard Installation Booklet 19 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationKirra Buffet Assembly Instructions
Thank you for your purchase. lease follow the instructions below for correct assembly. C B dowel screw x x6 wedge x4 screw x4 bolt x locking nut x long screw x F screw slide x6 rail x N wheel x4 G slide
More informationWallbeds Northwest ENDURA CABINET PLANS AND INSTRUCTIONS
Thank you for purchasing your Wall Bed from Wallbeds Northwest. If you have purchased a complete "Endura DIY Kit," then much of the work is already done for you. Please skip to assembly instructions. Note
More informationJesse Entertainment Unit Assembly Instructions
esse ntertainment Unit ssembly nstructions Thank you for your purchase. Please follow the instructions below for correct assembly. bolt x32 dowel x16 D F small screw x16 L + R L + R locking nut x32 cam
More informationx2 1/4 (6mm) Floor Anchor
INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Straight Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm
More informationThanks for shopping with Improvements! Wellesley Cart with Gate Leg Desk Extension Item #504992
Thanks for shopping with Improvements! Wellesley Cart with Gate Leg Desk Extension Item #504992 To order, call 1-800-642-2112 West Chester, OH 45069 Made in China PR-1015 If you have questions regarding
More informationVigilant Cigar Humidor Vault. Assembly Instructions
Vigilant Cigar Humidor Vault Assembly Instructions Models: 1000, 1500, and 2000 Congratulations! You have purchased a superior cigar humidor. These humidors have been specifically designed to properly
More informationPreference Collection 5543 Central Console INSTALLATION GUIDE
Preference Collection 5543 Central Console INSTALLATION GUIDE WARNING Failure to install the 5543 as described in this installation guide may cause the unit to collapse, resulting in serious injury to
More informationBARN DOOR HARDWARE KIT
INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Bent Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm x
More informationStuff-Your-Stuff Platform Bed (Twin and Full)
Stuff-Your-Stuff Platform Bed (Twin and Full) Pre-Assembly: Please read all instructions before beginning assembly. Assembly by two people is a must. Save all packing materials until assembly is complete
More informationINS T A L L A TIO N INS T R U C TIO N S. Ceiling Mount Track System
Ceiling Mount Track System 10.26.2016 Specifications Ceiling Post: Unassembled 2-7/8 Assembled 1-11/16 7/8 7-9/16 5-7/8 3/8 2 Tubes 1/2 2-3/8 5 Parts and Tools Tools Needed Tape Measure Pencil Drill with
More informationWILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS
WILDING WALLBEDS BUNK BED INSTALLATION INSTRUCTIONS With Storage Headboard INSTRUCTION BOOKLET #19 WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN POWERFUL LIFTING COMPONENTS. FAILURE TO USE AND FOLLOW THESE
More informationM. Door 1 Pc. 1 Pc. Door 1 Pc. 1 Pc. M3x20 Wood Screw (long) 8 Pcs. (+1 extra) M3x10 Wood Screw for Magnet 8 Pcs. (+1 extra)
88 5516 653 Barnside Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have
More informationPedestal Desk IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches
88 5549 181 Pedestal Desk IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have taken
More informationPantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or oth
88 5076 691 Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occurring to the parts. We have taken great
More informationStrata. urniture. Adriana Instructions. Parts in the Arm Box: Parts in the Body Box: Watch our assembly videos at
1A Watch our assembly videos at www.strataf.com/videos Parts in the Arm Box: Arm - Outside View Arm - Inside View 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached Back Panel
More informationInstallation Instruction
Tools Needed for Assembly Stud finder (for wood stud wall) Pencil Mark Electric drill Wood Stud Wall Installation Step 1. Locate the Wood Studs Installation Instruction Drill bit (for wood stud wall) Masonry
More informationLaminate Cabinet Installation Instructions
Laminate Cabinet Installation Instructions www.easygaragestorage.com/installation How To Use These Instructions Thank you for your purchase! Please read each step of this manual thoroughly to ensure proper
More informationPreference Collection and Treatment Console INSTALLATION GUIDE
Preference Collection 5580.69 and 5580.96 Treatment Console INSTALLATION GUIDE WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious
More informationRiverside. Windhaven Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 2 pcs. 4 pcs. 4 pcs. 4 pcs. 2 pcs. 5/0 Queen Storage Bed 50773 -- 5/0 Storage Footboard w/platform Note: The 50773 Storage Footboard can be used with the 50770 Panel Headboard
More informationD. Middle Panel. C. Middle Panel. 1 pc. B. Side Panel 1 pc. I. Back Stretcher. 1 pc. J. Front Stretcher. 1 pc. S. Door 1 pc. T.
itchen Cart IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the parts. We have taken great care
More informationQueen Wingback Bed King Wingback Bed
Parts and Hardware List A. Side Rails with Attachment Hooks 2 pcs B. Foot Rail 1 pc C. Head Rail 1 pc D. Center Support Slat 1 pc E. Leg Supports 3 pcs F. Support Slats 4 pcs G. Flat Washers 8 pcs H. Lock
More informationPRINCESS SINGLE BED WITH TRUNDLE
PRINCESS SINGLE BED WITH TRUNDLE If you have any questions regarding assembly or if you are missing parts, do not return this item to Sam s Wholesale Club Please call our customer service number and have
More informationL.L.Bean. Wooden Slat Bed
L.L.Bean Wooden Slat Bed Thank you for purchasing our Slat Bed. Assembly of this product requires A Phillips head screwdriver. We have found it helpful to have a second person present in at least one step
More informationRiverside. Harbor Hill Queen Storage Bed Assembly Instructions
Queen Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 2 pcs. 3 pcs. 3 pcs. 4 pcs. 4 pcs. 4 pcs. 1 pc. 1 pc. 8 pcs. 8 pcs. 8 pcs. 2 pcs. 8 pcs. 1 pc. 25770 -- 4/6-5/0 Panel Headboard (NOTE: the 25775 Leather
More informationEURO DELUXE INSTALLATION INSTRUCTIONS
WALLBEDS! TM EURO DELUXE INSTALLATION INSTRUCTIONS NOTE: Due to the arched top assembly, the assembly of this model is different from the standard wallbed assembly. PLEASE READ THROUGH THESE INSTRUCTIONS
More informationModels CW and AW Installation Instructions
Models CW and AW Installation Instructions Please keep these instructions for future reference. Hiddenbed must be dis-assembled before moving. a product of WALLBEDS! MODELS AW and CW HIDDENBED COMPONENTS
More informationRiverside. Harbor Hill King Storage Bed Assembly Instructions
King Storage Bed Page 1 of 7 8 pcs. 8 pcs. 1 pc. 2 pcs. 6 pcs. 3 pcs. 4 pcs. 4 pcs. 4 pcs. 1 pc. 1 pc. 2 pcs. 8 pcs. 8 pcs. 8 pcs. 8 pcs. 25780 -- 6/0-6/6 Panel Headboard (NOTE: the 25785 Leather Headboard
More informationStrata. urniture. Mission Rim Instructions. Parts in the Arm Box: Parts in the Body Box:
1A Watch our assembly videos at www.strataf.com/videos.html Parts in the Arm Box: Arm - Outside View Arm - Inside View Corbels x 4 1B Parts in the Body Box: Back Deck x 1 Seat Deck x 1 with the Feet attached
More informationFA968800TX Manchester Fireplace Console - Brown Mahogany Assembly Instructions
FA968800TX Manchester Fireplace Console - Brown Mahogany Assembly Instructions For assistance with assembly, contact: Southern Enterprises Inc. Customer Service 1-800-633-5096 service@seidal.com www.seidal.com
More informationa.k.a. casegoods instructions
a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly
More informationImportant Loading Information. Tools Required. Meridian Lateral Files Instructions
Y Meridian Lateral Files Instructions! WARNING Failure to observe stated capacities below will result in unsafe usage conditions, causing possible product damage or personal injury. Important Loading Information
More informationO-Sullivan King 4 Poster Bed O-Sullivan Queen 4 Poster Bed Parts and Hardware List
Parts and Hardware List A. Left Headboard Post 1 pc B. Right Headboard Post 1 pc C. Left Footboard Post 1 pc D. Right Footboard Post 1 pc E. Headboard Panel 1 pc F. Footboard Rail 1 pc. Spindles 4 pcs
More informationMounting Instructions Item No.: xxx
Mounting Instructions Item No.: 271.92.xxx Wall-Beds 1 General Notes For vertical folding beds Successful and safe installation of Bed-Lift and construction of casework requires a professional skill level
More informationv1.0 ASSEMBLY GUIDE Mia Wide Bookcase
v1.0 ASSEMBLY GUIDE Mia Wide Bookcase Components Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase.
More informationINSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE:
INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE: 268 June 22, 2010 TOOLS NEEDED COMPONENTS INCLUDED P2 Tip 3/8" Drill Rubber Gasket(s) x 2 Bracket(s) x 2 1/2" Drill Bit Bulkhead Flange #2 Phillips
More informationINSTALLATION INSTRUCTIONS for the JOMY RETRACTABLE LADDER. If there are any questions, please call (800)
INSTALLATION INSTRUCTIONS for the JOMY RETRACTABLE LADDER If there are any questions, please call (800) 255-2591 INSTALLATION INSTRUCTIONS WARNING! Ladder Sections Lock When Closed. Do Not Install or Close
More informationx2 1/4 (6mm) Floor Anchor
Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Bent Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm x 90mm) Wall Screw x2
More informationPreference Collection 5580 Treatment Console INSTALLATION GUIDE
Preference Collection 5580 Treatment Console INSTALLATION GUIDE 0 WARNING Failure to install the 5580 as described in this installation guide may cause the unit to collapse, resulting in serious injury
More informationASSEMBLY GUIDE. Mia Narrow Bookcase
ASSEMBLY GUIDE Mia Narrow Bookcase Components: Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase. Step
More informationTopo Freestanding Applications - Private Office
4 3 2 Topo Freestanding Applications - Private Office Combo Wrench If you have a problem, question, or request, call your local dealer, or Coalesse at 1.800.627.6770 Or visit our website: www.coalesse.com
More informationHeavy Duty I-Beam Trolley
Heavy Duty I-Beam Trolley ASSEMBLY INSTRUCTIONS I-BEAM TROLLEY Recommended Tools Level Tape Measure Pencil Drill with 1/8, 1/4, and 3/8, Drill Bits and Phillips Bit Socket Wrench with 9/16 Socket I-BEAM
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More informationAssembly and installation help
Assembly and installation help A supplement to the directions The Purpose of this tutorial is to expand (not replace) upon the directions that come with the system and to help provide shortcuts, the first
More informationSentinel Series Cigar Humidor End Tables
Sentinel Series Cigar Humidor End Tables Assembly Instructions Models: Sentinel 500, 1000 and 1500 Style: Contemporary SENTINEL ASSEMBLY INSTRUCTIONS Congratulations! You have purchased a superior cigar
More informationThe SwingAway ('CEVNT') Bed Assembly Instructions
The SwingAway ('CEVNT') Bed Assembly Instructions Issued 18/07/10, Hideaway Beds Ltd Updated: 2/3/12, 15/05/12, 19/05/16, 13/07/17 By using this Assembly Guide, you hereby agree to the following: Our own
More informationColonial Classic Bar
88 5528 991 Colonial Classic Bar IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts.
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationGeneral Features. Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized
General Features Low Profile. The SMART BOXX stands only 1.5 off of the bed of your truck so cargo space is maximized Two Sizes Short Box :74 L X 47 W X 7 T and Long Box 92 L X 47 W X 7 T All Aluminium
More informationMS555200TX Porter Gaming/Media Console Espresso Finish Assembly Instructions
MS55500TX Porter Gaming/Media Console Espresso Finish Assembly Instructions For assistance with assembly, contact: Southern Enterprises Inc. Customer Service 1-800-6-5096 service@seidal.com www.seidal.com
More informationVC-TABLE. Assembly Instructions
VC-TABLE Assembly Instructions Thank you for purchasing AVFI's Video Conferencing Table. This product was designed for multiple configurations. Connecting furniture will have its own instructions. Page
More informationHomestead Bar Cabinet IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent s
88 5527 991 Homestead Bar Cabinet IMPRTANT NTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts.
More informationThanks for shopping with Improvements! Louvered Space Saver Cabinet Item #512059
Thanks for shopping with Improvements! Louvered Space Saver Cabinet Item #512059 Note: Read these instructions carefully before assembling. Tools required: Philips screwdriver (not included). Find a clean,
More informationS214 / S215 ASSEMBLY INSTRUCTIONS. Assembly tools required : Hammer, Phillips # 2, #3 and regular screwdriver, 10 and 17mm wrenches
S14 / S15 ASSEMBLY INSTRUCTIONS Assembly tools required : Hammer, Phillips #, #3 and regular screwdriver, 10 and 17mm wrenches Special Notes : To make the assembly simple and well done, you have to be
More informationC PART LIST HARDWARE LIST. Kitchen Cart IMPORTANT NOTE
88 9200 006C Kitchen Cart IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the parts. We have taken
More informationJ. Base 1 pc. 1 pc. P. Shelf 2 pcs. Gate Leg. 1 pc. Head Cap Bolt 13 pcs. (+1 extra) Cam Lock Screw. Cam Lock. 20 pcs. (+1 extra)
88 5023 95C Kitchen Island with Breakfast Bar IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the
More informationTRUE TECHNICAL SERVICE MANUAL - ALL MODELS. DOORS/DRAWERS/LIDS
DOORS/DRAWERS/LIDS 55 56 NOTES DOORS/DRAWERS/LIDS Springs 97 TORSION SPRING REPLACEMENT GDM RADIUS FRONT - SWING DOOR INSTALLATION INSTRUCTIONS Tools Required (2) - 1 8" drift Punch (forged) Needle-Nose
More informationLOFT DOOR HANGER BARN DOORS & HARDWARE. Hardware Installation Instructions. Page
LOFT DOOR HANGER Page 1 Specifications 2 7/16" 3/8" 1-1/2 1-3/4 Ø3 3 7/8" 11-1/16 Page 2 Parts and Tools Tools Needed Tape Measure Pencil Drill with 1/8, 1/4 and 3/8 bits, 1 spade bit and Phillips bit
More informationSteel Frame Assembly
Steel Frame Assembly The Alpha Steel Frame is adaptable as vertical or horizontal bed. Note: A leg connector rod extension bar is required for a horizontal bed. Hardware Card #3 is used for Steel Frame
More informationBD101K / BD101K INSTALLATION GUIDE BARN DOOR HARDWARE TOP OF DOOR STRAP KIT
Common Components x1 Right Stopper x1 Left Stopper x2 Top of Door Strap x2 Anti-jump Block x2 #8 (4.2mm x 25mm) Floor Screws x2 1/4 (6mm) Floor Anchor x1 Internal Floor-Mounted Door Guide BD850-BR/MB/SS
More informationRTA-3520 DIMENSIONS MAXIMUM WEIGHT CAPACITIES. Product Size: 47.5"W x 23"D x 30"H
MODEL RTA - 3520 Thanks for purchasing one of our products. Please read carefully the assembly instructions before the installation. Please save this manual for future reference. Complete video assembly
More informationPFW Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids
Maximum Flat Panel Weight: 100 lb. / 45.35 kg. Included Components Wall Mount (Qty 1) Extension Bracket (Qty 1 Pair) Bracket (Qty 1 Pair) 5/16 Flat Washers (Qty 4) Universal Spacers (Qty 8) M5 Allen Driver
More information#916 CLASSIC 16 GUN CABINET ASSEMBLY INSTRUCTIONS
Thank you for purchasing this quality product. A list of PARTS and INSTRUCTIONS is included to assist you. Unpack and identify all parts included on the Parts List and Hardware List. If parts are missing,
More informationAdjustable Countertop Installation
Adjustable Countertop Installation Applies to Models: A1, A2, A3, A4, A5, & A6 Required Tools: Stud Finder, Level 1/4 deep well socket, Screwdrivers, Tape Measure, Drill and Drill Bits Language of origin:
More informationGared Pro-S Portable Backstop
Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION
More informationB. Side Panel. E. Middle Panel 1 pc. 1 pc. 1 pc. S. Side Rack. 1 pc. T. Base Rack. U. Pipe 3 pcs. M6x35 Head Cap Bolt 14 pcs.
IMPORTANT 88 5089 95C Kitchen Cart Carefully remove all the parts from the carton and place them individually on a soft cloth to prevent scratches or other damage. Carefully and strictly follow these assembly
More informationMedium HoneyBadger Chase Rack Installation Instructions
PREPARATION Medium HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend reading
More informationSINGLE TRACK BYPASS (patent pending) barn door hardware
SINGLE TRACK BYPASS (patent pending) barn door hardware Installation Manual What is included in your kit: Part number Part name Quantity 1 Inner door hanger 2 2 Outer door hanger 2 3 5/16 x 1.5 lag bolts
More informationInstallation Manual MODEL ANE-42
Installation Manual MODEL ANE-42 GET TO KNOW YOUR UNIT 1 2 1. CROSS BRACES 2. SIDE BRACKETS - Stud Finder - 12-14 Level - Tape Measure - Small Flathead Screwdriver Tools Needed: - Electric Drill (with
More informationDX-TVMLPTB03. Low-Profile TV Wall Mount ASSEMBLY GUIDE. For either wood-stud or concrete wall installations
ASSEMBLY GUIDE DX-TVMLPTB03 Low-Profile TV Wall Mount For either wood-stud or concrete wall installations Safety information and specifications...2 Tools needed...........................3 Package contents......................3
More informationHeavy-Duty Bypass Track System
Heavy-Duty Bypass Track System Please Note: This track system must be installed with the screws going into a solid surface such as studs or a header. Due to the spacing of the holes on these Brackets,
More informationLeft Unit. G. Shelf 1 pc. Small Cam Lock 6 pcs.(+1 extra) Cam Lock Screw 2 pcs.(+1 extra) Cam Lock Screw 6 pcs.(+1 extra)
88 5180 181 Art & Craft Computer Desk (Cottage Oak) IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring
More informationCopyright 2010, by Walker Edison Furniture Co., LLC. All rights reserved.
General Assembly Guidelines I. Insure that all parts and hardware are available before beginning assembly. II. III. IV. Follow each step carefully to insure the proper assembly of this product. Two people
More information