SignComp TITLE DETAIL A

Transcription

1 PRTS LIST PRT# ESRIPTION K9 Part in Single Face ody ssembly K90/ Part Inner / Outer Frame ssembly 590 Retainer Screw rill /" pilot hole Place the frame tight to the body before fastening. Ship To: Sales Order#: ETIL NOTE: PRE-UT KITS RE NOT PRE-RILLE. rilling of pilot holes are to be done by fabricator.) THIS RWING WS RETE T NO HRGE TO SSIST YOU IN VISULIZING OUR PROPOSL. THE RWING HEREIN IS THE PROPERTY OF SIGNOMP. PERMISSION TO OPY OR ISE THIS RWING OR TO USE THIS RWING FOR PROUTION IS STRITLY PROHIITE N N ONLY E OPIE, ISE OR USE FOR PROUTION WITH THE EXPRESSE WRITTEN PERMISSION OF SIGNOMP. RWN Sreihof entroid Y: in Principal Moments Ix: in^ Principal Moments Iy: in^ Section Modulus Ix: in^ Section Modulus Iy: in^ Signomp //0 entroid X: in Part in Single Face ody w/ Vandal Frame - ssembly WG NO K9/0/ SHEET OF

2 PRTS LIST PRT # ESRIPTION 9 Part in Single Face ody Top & ottom 9 Part in Single Face ody Sides 59 Part Part in ody orner ngle 50 orner Key 5 orner ngle Screw rill 5/" pilot hole orner Key floats in the extrusion helping align the mitres while providing additional strength. ETIL ETIL NOTE: PRE-UT KITS RE NOT PRE-RILLE. rilling of pilot holes are to be done by fabricator.) THIS RWING WS RETE T NO HRGE TO SSIST YOU IN VISULIZING OUR PROPOSL. THE RWING HEREIN IS THE PROPERTY OF SIGNOMP. PERMISSION TO OPY OR ISE THIS RWING OR TO USE THIS RWING FOR PROUTION IS STRITLY PROHIITE N N ONLY E OPIE, ISE OR USE FOR PROUTION WITH THE EXPRESSE WRITTEN PERMISSION OF SIGNOMP. RWN Sreihof Principal Moments Iy: in^ Section Modulus Ix: in^ Section Modulus Iy: in^ entroid Y: in Principal Moments Ix: in^ Ship To: Sales Order#: Signomp //0 entroid X: in Part in Single Face ody - ssembly WG NO K9 SHEET OF

3 PRT # ESRIPTION Part Inner Frame Part Inner Frame orner Key Part Inner Frame orner Screw Top & ottom Ends rill # ounter Sink ETIL NOTE: PRE-UT KITS RE NOT PRE-RILLE. rilling of pilot holes are to be done by fabricator.) THIS RWING WS RETE T NO HRGE TO SSIST YOU IN VISULIZING OUR PROPOSL. THE RWING HEREIN IS THE PROPERTY OF SIGNOMP. PERMISSION TO OPY OR ISE THIS RWING OR TO USE THIS RWING FOR PROUTION IS STRITLY PROHIITE N N ONLY E OPIE, ISE OR USE FOR PROUTION WITH THE EXPRESSE WRITTEN PERMISSION OF SIGNOMP. RWN Steve //00 HEKE Signomp Q Part Inner Frame - ssembly PPROVE SLE WG NO 90 SHEET OF

4 0 PRT # ESRIPTION Part Outer Frame Part Outer Frame Part Outer Frame orner ngle Part Outer Frame orner ngle Screw Top & ottom Ends rill # ounter Sink 0 0 ETIL ETIL NOTE: PRE-UT KITS RE NOT PRE-RILLE. rilling of pilot holes are to be done by fabricator.) THIS RWING WS RETE T NO HRGE TO SSIST YOU IN VISULIZING OUR PROPOSL. THE RWING HEREIN IS THE PROPERTY OF SIGNOMP. PERMISSION TO OPY OR ISE THIS RWING OR TO USE THIS RWING FOR PROUTION IS STRITLY PROHIITE N N ONLY E OPIE, ISE OR USE FOR PROUTION WITH THE EXPRESSE WRITTEN PERMISSION OF SIGNOMP. RWN Steve //00 HEKE Signomp Q Part Outer Frame 0 PPROVE SLE WG NO 9 SHEET OF

5 5 PRT # ESRIPTION Part Outer Frame Hinge Fastener Part Hinge Part Lock Lock Nut Lock Washer am am Nut /" Pop Rivet or # ounter Sunk Screw rill /" Hole - See etail "" n.50 x.5 ETIL ETIL - ETIL NOTE: PRE-UT KITS RE NOT PRE-RILLE. rilling of pilot holes are to be done by fabricator.) TIP: High bond tape or bonding agents can be used to help secure the hinge to the frame and assist in the installation of the hinge. e careful not to get the tape on the barrel of the hinge. To do so may cause the hinge not to open properly. THIS RWING WS RETE T NO HRGE TO SSIST YOU IN VISULIZING OUR PROPOSL. THE RWING HEREIN IS THE PROPERTY OF SIGNOMP. PERMISSION TO OPY OR ISE THIS RWING OR TO USE THIS RWING FOR PROUTION IS STRITLY PROHIITE N N ONLY E OPIE, ISE OR USE FOR PROUTION WITH THE EXPRESSE WRITTEN PERMISSION OF SIGNOMP. RWN Steve //00 HEKE Signomp Q PPROVE SLE Part Outer Frame - Part Hinge - Part Lock - ssembly WG NO SHEET OF

6 PRT # K90 K9 ESRIPTION Part Inner Fame Part Outer Frame Hinge Fastener ssembly ssembly /" Pop Rivet or # ounter Sunk Fastener lign the back of the hinge up tight with the face of the locking tab. NOTE: PRE-UT KITS RE NOT PRE-RILLE. rilling of pilot holes are to be done by fabricator.) TIP: High bond tape or bonding agents can be used to help secure the hinge to the frame and assist in the installation of the hinge. e careful not to get the tape on the barrel of the hinge. To do so may cause the hinge not to open properly. THIS RWING WS RETE T NO HRGE TO SSIST YOU IN VISULIZING OUR PROPOSL. THE RWING HEREIN IS THE PROPERTY OF SIGNOMP. PERMISSION TO OPY OR ISE THIS RWING OR TO USE THIS RWING FOR PROUTION IS STRITLY PROHIITE N N ONLY E OPIE, ISE OR USE FOR PROUTION WITH THE EXPRESSE WRITTEN PERMISSION OF SIGNOMP. RWN Steve //00 HEKE Signomp Q PPROVE Part Inner Frame - Part Outer Frame - ssembly SLE WG NO 90- SHEET OF