RangerWare Fiberglass Door System Installation Instructions P/N
|
|
- Alfred Atkins
- 5 years ago
- Views:
Transcription
1 Page 1 of 9 RangerWare Fiberglass Door System Installation Instructions P/N
2 ORDER OF INSTALLATION Note: To assure proper order, read all Accessory Installation Instructions before beginning. 1. Heater 2. Windshield Wiper (Installed in the Windshield) 3. Rear Panel 4. Door Thresholds 5. Windshield 6. Roof 7. Wire Harness (Roof) 8. Doors Page 2 of 9
3 Application: Polaris Ranger MY 2010 Before you begin, read these instructions and check to be sure all parts and tools are in your kit. Retain these installation instructions for future reference. Door and frame hardware kit Qty Description 1 Mounting plate for the latch pin drivers side 1 Mounting plate for the latch pin passengers side 2 Striker Pin 2 Nut jam M12x1.0 2 Washer Lock ½ for striker 6 Clamp Vinyl 1-1/4" 2 Clamp Vinyl 1-3/4" 8 Bolt 1/4-20x3.5 UNC BHSCS 6 Bolt 1/4-20x2 UNC BHSCS 2 Bolt 1/4-20x1.5 UNC BHSCS 6 Bolt 1/4-20x1 UNC BHSCS 6 Bolt 1/4-20x.75 UNC BHSCS 28 Nut Nylock 1/4-20 UNC 26 Washer ¼ Flat Washer 2 Washer ¼ Fender Washer 28 1/4" Bonded Washer 2 1 Nylon Spacers Foam Tape 3/8 x 1 x 6 2 Templates You will need to supply: 5/32 Alan bit Cordless drill 7/16 Wrench or Socket ½ Wrench ¾ Wrench x2 5/16 Drill bit 9/32 Drill Bit Tape Note: This is a two person installation. IMPORTANT: To ensure satisfactory installation, perform all installation steps correctly in the sequence as shown in these instructions. NOTES: Leave all fasteners loose until all the panels are installed and properly located. Page 3 of 9
4 *When all panels are installed tighten fasteners only until a slight dimple appears in the Gelcoat finish. DO NOT OVER TIGHTEN!!! *On all ¼ use a rubber bonded washer on the exterior and flat washer and nylock nut on the interior. INSTALLATION INSTRUCTIONS 1. Follow the instructions (1-3) of the Top & Rear Panel installation. Be sure to position the upper vinyl clamp on each side of the roll cage. Both driver and passenger side clamps are located as shown here. Figure 1 2. Install the lower side panel. First locate the supplied drilling template. This template needs to be taped onto the machine. Align as shown in Figure 2. It will locate where to drill the fastener holes. Be sure to use ample tape so the template doesn t move when drilling. This stage is critical. BE SURE THE TEMPLATE IS ALIGNED PROPERLY. Page 4 of 9
5 2 bolts 3-1/2 bolt Tip: Angle the drill bit forward on this hole only. Driver side template has notch. Align the bottom and front edges as shown. Figure 2 3. Once the template is secured in place. Feel behind the aft 2 bolt location marked with an X in figure There is a wall on the inside fender that the drill hole must be in front of for you to be able to install a nut. Use a 5/16 drill bit to drill through the template and the plastic. You will have to drill through the outside fender and the inside fender so you can get the nut and washer on the bolt. The 3-1/2 bolt will come into the cab storage area. The 2 bolts will be reached from the fender well opening. 4. Next the lower drill template will need to be located and aligned on the bottom frame. The template is symmetrical and will be used for both the drivers and passenger s side. Again use a 5/16 drill bit and drill through the plastic rocker panel and the inside and outside walls of the lower frame. 3-1/2 bolts Reminder: All exterior bolts need a Rubber Bonded washer under the bolt head. A ¼ flat washer with a ¼ nylock nut on the back side. Use a straight edge in these two locations. The template needs to be flush with the floor. The template is flush with the back and bottom. Figure 3 Page 5 of 9
6 Note: It is recommended that you drill all of the holes for either the drivers or passenger side and then install that side before drilling the opposite side. Caution: When drilling the lower rocker panel holes on the passenger side, use extreme care not to drill into the fuel tank. Inspect the area prior to drilling and note the location of the fuel tank. Use a sharp, short drill bit and drill carefully. 5. After the template holes are drilled on one side fasten that panel to the machine. Push the panel in tight against the rear panel and use the hole in the panel as a guide to drill a 9/32 hole thru the frame. Use the spacers between the panel and the frame. The bottom threshold bolts should be tightened just enough for the foam to seal and bolts to not rattle. Drill here using hole as guide. 2 bolt, 1/4 flat bonded washer with 1 Nylon spacer, 1/4 flat washer & then 1/4 nylock nut. Figure 4 Repeat steps 2 through 5 for the opposite side panel 6. Install the upper side panel. The panel will bolt directly to the lower side panel and through one clamp on the roll bar. Once the roof and windshield are installed you may need to apply foam spacing tape in the area shown to ensure that the upper panel fits snugly against the roof and windshield. Page 6 of 9
7 Add foam spacing tape in this area as necessary. NOTE: Usually requires a single layer on each side. Occasionally a double layer or none at all is required. 1-1/2 bolt This bolt goes thru the Roll cage clamp. Use a ¼ between clamp & bolt. 1 bolt (B) Tightening this bolt will pull door in at Top Rear. (A) Leave this bolt loose to access the lower hinge locknuts. Tighten after the doors & hinges have been adjusted and tightened. This bolt will also pull in the back of door as tightened Figure 5 7. Install the windshield and roof. Make sure the threshold panel fits inside the windshield, roof and rear panel. 8. Adjust and position all panels and tighten all fasteners (complete the instructions for the windshield and top and back panel). **Except as noted in the photo above** 9. Now install the striker plates and striker pins. The hole for the pin is slotted for in and out travel. This can be adjusted for a tighter fit when the door is closed. Page 7 of 9
8 3) 1-1/4 clamps. Note: The door latch has 2 catch positions. Adjust the striker pin to fully engage the second position. Striker pin, 12M- 1.0 jam nut. ½ lock washer behind 12M-1.0. These holes will be slotted for left to right travel. ¼ x ¾ bolt. Figure Hang the door. The hinge halves that are on the upper and lower side panels are slotted and may need alignment for the door to be mounted. The hinges on the doors are aligned from the factory and we recommend not adjusting them. Once the door is hanging, slowly shut it until it hits the striker pin. Adjust the pin and plate as needed for the latch to catch and compress the seal around the perimeter. Also, as you are doing this you will need to watch the outside perimeter of the door and make sure it is centered in the door jamb. Adjust the door until getting a consistent gap between the door and the surrounds. There are slots in the hinges for this. In extreme cases you may need to adjust the door surrounds. This bolt in the center of the lower side panel also adjusts the door. Tightening this screw will put more pressure on the front door seal and move the door slightly toward the rear of the vehicle as well as bring the upper rear of door in. This gap should be consistent around the entire perimeter. Figure 7 Page 8 of 9
9 11. After the door is hung and adjusted properly install the supplied nylon strap (door stop). The hinge bolts will go through the strap. Figure 8 Page 9 of 9
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.
More informationInstallation for Full Size Polaris Ranger Crew Doors
Installation for Full Size Polaris Ranger Crew Doors Order of Installation: Heater Doors Wiper on to Windshield Windshield Top & Back Panel Note: Most of the steps in these instructions need to be repeated
More informationINSTALLATION INSTRUCTIONS RH 412 STEEL DOORS
By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side. Note: Having the hood open makes the job
More informationWPS crew Doors Installation instructions
WPS-132-133 crew Doors Installation instructions ORDER OF INSTALLATION FOR A COMPLETE ENCLOSURE OF A CREW WPS (Weather Protection System) IS AS FOLLOWS: 1. Heater 2. Rear Thresholds - Right Hand & Left
More informationINSTALLATION INSTRUCTIONS
NOTE: Bolts should remain hand tight until all bolts are installed. STEP 1 Installing the door base (both sides). 1. Locate the outer, roll cage, mounting bolt (passenger side is shown in the illustration).
More informationINSTALLATION & OWNER S MANUAL
Rev. O p. 1 of 16 INSTALLATION & OWNER S MANUAL V4213 BALL CAGE KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation
More informationRZR 4 Doors Part # Polaris RZR XP & Turbo ( ) Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com RZR 4 Doors Part # 07-1802 Polaris RZR XP 4 1000 & Turbo (2015-2018) Black Revision No: 01 Revision Date:
More informationINSTALLATION INSTRUCTIONS KK-K9-C12-K CHEVY IMPALA
INSTALLATION INSTRUCTIONS KK-K9-C12-K 2000-2005 CHEVY IMPALA READ ALL INSTRUCTIONS PRIOR TO INSTALLATION TOOLS REQUIRED: Power Drill Drill bits1/4 and 5/32 7/l6 wrench and socket 15,18 and\or 19mm socket
More informationBe sure any accessory used will fit with the soft upper doors before installing. Not all accessories will be compatible.
Company Name: Spike Power Sports Vehicle Name: Polaris General 2P Product Description: Soft Upper Doors Part Number: 58-1600 Revision: R01 09/19/2018 Contents: 655 Elm Ridge Ave, Canal Fulton OH, 44614
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory FABRIC REAR DOORS (5P) P/N 0SR90-HL4-211B (BLACK) P/N 0SR90-HL4-211C (CAMO) Application SXS1000M5P/M5D Honda Dealer: Please give a copy of these instructions to your
More informationVIEWPOINT ALUMINUM RUNNING BOARD TOYOTA RAV4
PARTS LIST: VIEWPOINT ALUMINUM RUNNING BOARD 1 Driver/Left Running Board 4 10-1.5mm x 50mm T-Bolt 1 Passenger/Right Running Board 12 10mm Plastic Retainers 1 Driver/Left Bracket 2 10-1.50mm x 40mm Hex
More informationKawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions.
Owner s Manual Model: Kawasaki Teryx 750 Kawasaki Teryx 750 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Safety Instructions Cab Kit Contents Hardware
More information6 Passenger Roof Assembly & Installation
6 Passenger Roof Assembly & Installation Tools Required Supplied Components Hand Drill Quantity Description ¼ Drill Bit 3 Roof Sections 7/16 End Wrench 2 5 H Molding 7/16 Socket & Socket Wrench 2 Edge
More informationCREW REAR DOOR KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
CREW REAR DOOR KIT P/N 2883437 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
More informationBOX-118 E-Z-Go TXT Utility Box Mounting Kit Installation Instructions
BOX-118 E-Z-Go TXT Utility Box Mounting Kit Installation Instructions Contents of BOX-118 Utility Box Mounting Kit: a (1 ea.) Utility Box Support Frame, Driver Side b (1 ea.) Utility Box Support Frame,
More informationAssembly Instructions
10' and 12' Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/20/09 Cedar Gazebo Assembly Instructions
More information1. Begin by rolling your window up all the way 2. Remove your door and window handles by unscrewing the flat head set screws behind each handle.
1. Begin by rolling your window up all the way 2. Remove your door and window handles by unscrewing the flat head set screws behind each handle. 3. Remove the 12 screws that attach the steel interior door
More informationBOX-117 E-Z-Go RXV Utility Box Mounting Kit Installation Instructions
BOX-117 E-Z-Go RXV Utility Box Mounting Kit Installation Instructions Contents of BOX-117 Utility Box Mounting Kit: a (1 ea.) Utility Box Support Frame, Driver Side b (1 ea.) Utility Box Support Frame,
More informationBefore returning this product to the store of purchase
Before returning this product to the store of purchase Contact Dee Zee if you experience the following problems: Missing Parts Installation Problems/Questions Warranty Questions 1.800.779.2102 Hours of
More informationK9 KIT INSTALLATION INSTRUCTIONS CROWN VIC KK-K9-F7-K
K9 KIT INSTALLATION INSTRUCTIONS 1998-2011 CROWN VIC KK-K9-F7-K TOOLS REQUIRED: Power Drill (Cordless preferable) Drill Bit Set Standard Wrench and Socket Set Metric Socket Set Screwdriver Set Torx Bit
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationPolaris General Doors #06016 Installation & Operations Manual Fits Polaris General
Polaris General Doors #06016 Installation & Operations Manual Fits Polaris General Before You Start: Please familiarize yourself with all the steps before beginning assembly. Compatibility Info: This Door
More informationKWIK-KIT KK-S INSTALLATION INSTRUCTION PACKAGE
KWIK-KIT KK-S-120-02 INSTALLATION INSTRUCTION PACKAGE INSTALLATION INSTRUCTIONS HAVIS KWIK-KIT KK-S-120-02 2002-2007 DODGE/FREIGHTLINER SPRINTER VAN PLEASE READ COMPLETE INSTRUCTIONS PRIOR TO INSTALLATION
More informationBOX-115 Club Car Precedent Utility Box Mounting Kit Installation Instructions
BOX-115 Club Car Precedent Utility Box Mounting Kit Installation Instructions Contents of BOX-115 Utility Box Mounting Kit: a (1 ea.) Utility Box Support Frame, Passenger Side b (1 ea.) Utility Box Support
More informationUPPER DOOR KIT P/N
UPPER DOOR KIT P/N 2879946 Application RZR XP4 1000 Before you begin, read these instructions twice and check to be sure all parts and tools are accounted for. Please retain these installation instructions
More informationBulkhead Model Number and
Bulkhead Model Number 96141-3-01 and 96142-3-01 Installing your ProMaster bulkhead is very clear cut following these instructions. Before cutting or drilling in the floor, verify the location of you gas
More informationDOOR KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev Page 1 of 6. Verify accessory fitment at Polaris.com.
DOOR KIT P/N 2882528 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these installation
More informationK9 KIT INSTALLATION INSTRUCTIONS CROWN VIC with Fire Suppression System Model KK-K9-F7-K-FS
K9 KIT INSTALLATION INSTRUCTIONS 2005-2011 CROWN VIC with Fire Suppression System Model KK-K9-F7-K-FS TOOLS REQUIRED: Power Drill (Cordless preferable) Drill Bit Set Standard Wrench and Socket Set Metric
More informationINSTALLATION INSTRUCTIONS SIDE BAR FORD ESCAPE & MAZDA TRIBUTE PART #
INSTALLATION INSTRUCTIONS SIDE BAR 2008-2010 FORD ESCAPE & MAZDA TRIBUTE PART # 50136 50137 PARTS LIST: 1 Driver/Left Sidebar 2 10-1.50mm x 35mm Bolt Plate 1 Passenger/Right Sidebar 2 10-1.50mm x 30mm
More informationMid Size Ranger Pro-fit Doors #06023 Installation & Operations Manual
Mid Size Ranger Pro-fit Doors #06023 Installation & Operations Manual Before You Start: Please familiarize yourself with all the steps before beginning assembly. Compatibility Info: This Door System is
More informationFull Size Ranger Pro-fit Doors #06015 Installation & Operations Manual
Full Size Ranger Pro-fit Doors #06015 Installation & Operations Manual Before You Start: Please familiarize yourself with all the steps before beginning assembly. Compatibility Info: This Door System is
More informationHisun Deluxe Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Owner s Manual.
Owner s Manual Model: Hisun Hisun Deluxe Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Safety Instructions Cab kit Contents Hardware Assembly Panel Assembly
More informationOctagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models
Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS PLATINUM 4 OVAL STEP BAR (90 BENT END) APPLICATION: 2010-2015 Dodge Ram 2500/3500 Mega Cab PART NUMBER: 21-3570, 21-3575, 23-3570, 23-3575, 25-3570, 25-3575,
More information10 Octagon Cedar Gazebo Assembly Instructions
10 Octagon Cedar Gazebo Assembly Instructions Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 06/22/09 10 Cedar Gazebo Assembly Instructions
More informationINSTALLATION GUIDE. C20-FTL STRAIGHT PARTITION Transit Partition ( Perforated Window, No Access, Steel )
INSTALLATION GUIDE C20-FTL STRAIGHT PARTITION Transit Partition ( Perforated Window, No Access, Steel ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... q 1.2 Partition Assembly... 3-5 5-6 Phase 2 -
More informationGRILLE GUARD SPRINTER VAN (EXCLUDES X4) INCLUDES MERCEDES, FREIGHTLINER AND DODGE PARTS LIST:
PARTS LIST: 1 Grille Guard 8 12mm Hex Nuts 1 Driver/Left Side Frame Mounting Bracket 2 10-1.50mm x 25mm Button Head Bolts 1 Passenger/Right Side Frame Mounting Bracket 4 10mm x 20mm OD x 2mm Flat Washers
More information(W) INSTALLATION INSTRUCTIONS 3" ROUND & 4" OVAL SIDEBAR (90-DEG BENT END) DODGE RAM 1500 QUAD CAB PART #DZ /DZ /DZ /DZ
(W) INSTALLATION INSTRUCTIONS 3" ROUND & 4" OVAL SIDEBAR (90-DEG BENT END) PART #DZ 372231/DZ 372233/DZ 372237/DZ 372239 PARTS LIST: 3" ROUND & 4" OVAL SIDEBAR (90-DEG BENT END) Qty Description Qty Description
More informationINSTALLATION INSTRUCTIONS 3"/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ
INSTALLATION INSTRUCTIONS 09-12 FORD F-150 SUPERCREW PART # DZ 372697/DZ 372699 PARTS LIST: 1 Driver/Left Sidebar 4 1/2 Lock Washers 1 Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Mounting
More informationUPPER DOOR KIT P/N APPLICATION BEFORE YOU BEGIN ITEMS MARKED (*) ARE INCLUDED IN HARDWARE KIT PN P/N Rev 01 07/14 Page 1 of 6
UPPER DOOR KIT P/N 2880609 APPLICATION RZR 900 BEFORE YOU BEGIN Read these instructions thoroughly and make sure all parts and tools are accounted for. Please retain these installation instructions for
More information55000/55010 Installation Instructions
A. Install 55015 B. Bolt roof rails, 55020/55025, to front hoop. C. Assemble 55026 D. To install without drilling into bumper. E. If mounting directly to bumper. A. 55015 Installation Instructions 55000/55010
More informationINSTALLATION INSTRUCTIONS
TEL -866-XANATOS INSTALLATION INSTRUCTIONS PART#: 7D5000SS\7D500A GRILL GUARD FOR DODGE SPRINTER 07-09 PARTS LIST: 8 6 Grille Guard Driver/Left Frame Mounting Passenger/Right Frame Mounting Driver/Left
More informationRAMPAGE P R O D U C T S. INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO TOOLS REQUIRED
RAMPAGE P R O D U C T S 84 (+/- 1/4 ) INSTALLATION INSTRUCTIONS BRONCO ZIPPER FASTRACK TOP PART #984xx BRONCO 1966-1977 TOOLS REQUIRED 3/8 WRENCH 7/16 WRENCH ½ WRENCH #2 PHILLIPS SCREWDRIVER 1/8 DRILL
More informationTHIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE
Sal es@lambodoorscanada. com 2407A Kal adarave,ottawa,on K1V 8B9 THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE 2 SHOCKS 565 PSI 2 SHOULDER
More informationHONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual)
HONDA RIDGELINE (KIT #601) Installation Instructions (to be used in addition to owners manual) IMPORTANT NOTE: Read before beginning installation. These instructions replace all of Step 1 of the instructions
More informationWARNING!! DO NOT LIFT DOORS UP WHEN THE HOOD IS OPEN. THE DOORS WILL HIT THE HOOD!
WARNING!! DO NOT LIFT DOORS UP WHEN THE HOOD IS OPEN. THE DOORS WILL HIT THE HOOD! THIS KIT INCLUDES: 4 M8-1.25X30MM BOLTS WITH WASHERS 12 M8-1.25X40MM BOLTS WITH WASHERS 2 SHOULDER BOLTS WITH RIGHT AND
More information08+ KAWASAKI KLR PD NERF
08+ KAWASAKI KLR PD NERF 0505-1299 Before you begin, place the bike on a hard level surface where you have room to work. Lay out the parts included in this kit and compare to the parts list on page 5 of
More information8mm x 25mm "Z" Bolt Plates. (2) Tube Spacers. (2) 12mm Bolt Plates w/ Nut
PARTS LIST: 1 Grille Guard 10 12mm Lock Washers 1 Driver/Left Side Frame Mounting Bracket 8 12mm Hex Nuts 1 Passenger/Right Side Frame Mounting Bracket 2 10-1.50mm x 25mm Button Head Bolts 1 Driver/Left
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationCORVETTE CORVETTE REV: Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending.
CORVETTE 2005-2006 CORVETTE 2005-2007 REV: 7-2-07 Made in USA U.S. PATENT #6,808,223; #6,845,547; #7,140,075; #7,059,655 and other patents pending. Page 1 of 12 CORVETTE C6 2005-2007 THIS KIT INCLUDES:
More informationTIRE RACK INSTALLATION INSTRUCTIONS Dodge Sprinter
Aluminess Products Inc 9402 Wheatlands Ct. #A Santee, CA 92071 619-449-9930 TIRE RACK INSTALLATION INSTRUCTIONS 07-11 Dodge Sprinter Please read before beginning Stainless steel hardware may bind together
More information2 SHOULDER BOLTS RIGHT AND LEFT HINGE USE 4 EXISITING DOOR BOLTS TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER.
Page 1 of 12 NISSAN 350Z 2003-2004 THIS KIT INCLUDES: 8 BOLTS WITH WASHERS 2 SHOCKS 780 PSI 2 PINS 2 SHOULDER BOLTS RIGHT AND LEFT HINGE USE 4 EXISITING DOOR ASSEMBLY BOLTS TOOLS REQUIRED FOR INSTALLATION:
More informationINSTALLATION GUIDE FTX FLOOR Ford Transit ( 148" Extended Wheelbase )
INSTALLATION GUIDE 6540-FTX FLOOR Ford Transit ( 148" Extended Wheelbase ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... 3-4 Phase 2 - Installation q 2.1 Install Preparation... q 2.2 Floor Installation...
More informationPolaris XP Doors (P144202) Installation Instructions
Polaris XP4 000 Doors (P440) Installation Instructions WARNING Pro Armor Door and Net are designed to work together to replace your original equipment nets and/or door. Install both the Pro Armor Door
More informationPassenger/Right Center and Rear Support Brackets. Driver/Left Center and
PARTS LIST: 1 Driver/Left HD Running Board 24 8mm x 24mm OD x 2mm Flat Washers 1 Passenger/Right HD Running Board 12 s 3 Driver/Left front, passenger center/rear Support Brackets 6 8mm-1.25 Hex Nuts 3
More informationSEAT-361 E-Z-Go RXV RHOX Seat Kit Installation Instructions
SEAT-361 E-Z-Go RXV RHOX Seat Kit Installation Instructions Contents of SEAT-361 RHOX 300 Series Rear Seat Kit: a (1 ea.) Front Seat Back Support, Driver Side b (1 ea.) Front Seat Back Support, Passenger
More information40670 Transit Connect/NV200/City Express/ProMaster City Partition
40670 Transit Connect/NV200/City Express/ProMaster City Partition Top Panel (1) Bottom Panel (1) Transit Connect (2014) Top Angle (1) TC Top MNT BRKT (2) TC Bottom MNT PLT (2) NV200/City Express Top Mount
More informationInstruction Guide 4A90L
Instruction Guide 4A90L Kargo Master Rancho Cordova, CA 95742 800-343-7486 CustomerService@KargoMaster.com DATE: *PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING, INSTALLING, AND USING THIS
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART #
INSTALLATION INSTRUCTIONS GRILLE GUARD 09-ON DODGE RAM PART # PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Brackets (for trucks without 22 12mm x 30.1mm OD
More informationSupport. (3)Passenger Support. Brackets. (2) Running Board (example only)
IB(5,4)) RUNNING BOARD PARTS LIST: Item QTY Description Item QTY Description #01 2 Running Board(use for left or right) #10 12 8mm Lock Washers #02 3 Driver Mounting (/Center/Rear) #11 6 8mm Hex Nuts #03
More informationInstallation Instructions
DODGE RAM 2500 20K Industry Standard SuperRail Custom Mounting Kit #2336 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note,
More informationINSTALLATION GUIDE N5-DS48-4
INSTALLATION GUIDE N5-DS48-4 Shelving ( steel ) Transit High Roof & Medium Roof Promaster Standard Roof & High Roof Nissan NV High Roof Sprinter Low Roof & High Roof Box Truck / Trailer QUICK START GUIDE
More informationXHD Bull Bar w/ Dual Row LED Light Bar (10-17 Jeep JK)
XHD Bull Bar w/ Dual Row LED Light Bar (10-17 Jeep JK) PARTS LIST: 1 Driver/Left Side Bull Bar Upright 8 10-1.5mm Hex Nuts 1 Side Bull Bar Upright 4 10-1.5mm Nylon Lock Nuts 1 Top Cross Bar 2 Light Bar
More informationD. Drill Bolt Holes Through Topper Shell and Bed Rails
A. Check Mounting Kit Check to make sure that all of the following items are included in the mounting kit. Call 515-272-4372 if you need to obtain a part from BrandFX. Double-stick tape (1 roll) White
More informationINSTALLATION GUIDE Locker With Top Shelf Transit Low Roof & Nissan NV Low Roof ( Aluminum )
INSTALLATION GUIDE 7115 Locker With Top Shelf Transit Low Roof & Nissan NV Low Roof ( Aluminum ) QUICK START GUIDE Phase 1 - Assembly q 1.1 Setup... q 1.2 Locker w/ Top Shelf Assembly... 3-5 6-13 Phase
More informationEnclosed Partition Installation Instructions
Nissan NV1500/2500/3500 High Roof Partition Kit Part #: DTC 1502-036 V1.0.08.06.18 IMPORTANT INSTALLATION STEPS ARE DENOTED USING A STOP SIGN. THESE STEPS MUST BE PERFORMED IN THE SPECIFIED ORDER TO ENSURE
More informationATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING THIS PRODUCT.
VAN STORAGE SOLUTIONS FOR THE WAY YOU WORK TM INSTALLATION MANUAL BULKHEAD Model Number 96101-3-01 ATTENTION: PLEASE READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE ASSEMBLING, INSTALLING OR USING
More informationJEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK001 / KRJW014T INSTALL TIME: 2.5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationINSTALLATION INSTRUCTIONS 3 ROUND & 4 OVAL SIDEBAR (90-DEG BENT END) DODGE RAM MEGA CAB PART NUMBER SB1214S SB1214B
INSTALLATION INSTRUCTIONS PART NUMBER SB1214S SB1214B PARTS LIST: Qty Description Qty Description 1 Driver/Left Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Passenger/Right Sidebar 4 12mm Lock Washers
More informationGeneral Prisoner Transport Install Instructions PT-2-INST
General Prisoner Transport Install Instructions PT-2-INST 50 or 60 high x 80, 100 & 120 inch long / Double Compartment Inserts Also refer to PT-A-3XX instructions for vehicle specific mounting measurements
More informationTOYOTA TACOMA LED BED LIGHTS Preparation
Preparation Part Number: PT948-35160 Kit Contents Item # Quantity Reqd. Description 1 1 Hardware Kit 2 1 Driver Side LED assembly 3 1 Passenger Side LED assembly 4 1 Main Wire Harness Hardware Bag Contents
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Grille Guard/Winch Mount Kit 645 For Chevrolet Silverado 500HD & 3500 This WARN Trans4mer system can be customized to give your Chevy Silverado a wide variety of looks,
More informationBMW X5 OEM RUNNING BOARD PART#SBBW
INSTALLATION INSTRUCTIONS 2014-2016 BMW X5 OEM RUNNING BOARD PART#SBBW-146-74 QTY HARDWARE 1 Driver Side OEM Running Board 1 Passenger Side OEM Running Board 8 Rivet Pin 1 Page Step 1: Verify all parts
More informationKawasaki Teryx 2 Cab Kit* Caution: Before using this product, read this manual and follow all Safety Instructions. Owner s Manual
Owner s Manual Model: Kawasaki Teryx 2 Kawasaki Teryx 2 Cab Kit* Caution: efore using this product, read this manual and follow all Safety Instructions. Safety Instructions Cab Kit Contents Hardware ssembly
More informationOctagon Vinyl Gazebo Assembly Instructions
Octagon Vinyl Gazebo Assembly Instructions For 10 & 12 Models Toll Free: 866.768.8465 Hours: 9-5 Monday-Friday EST www.homeplacestructures.com Package ships as shown revised 04/29/09 Vinyl Gazebo Assembly
More information(6) Plastic Retainers. Passenger/Right. Passenger/Right Support Brackets
PART#R102580 PARTS LIST: 1 Driver/Left HD Running Board 4 8mm Bolt/Nut Plates 1 Passenger/Right HD Running Board 4 8mm Plastic Retainers 2 Driver/Left & Center Mount Bracket 14 8mm-1.25 x 30mm Hex Bolts
More informationJK Rear Inner Fenders
INSTALLATION INSTRUCTIONS INST-17-05-080_A JK Rear Inner Fenders IMPORTANT: Thank you for purchasing this Poison Spyder product. Please read through this entire document before proceeding with installation.
More informationPickup Box Utility Rack Package Installation (Instruction ID: )
017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation
More information1104. Clean up the door striker plates with a hand grinder using a wire brush and WD-40.
Chapter 31 - Misc. Putting VW Back Together (Video Clip 31) 1104. Clean up the door striker plates with a hand grinder using a wire brush and WD-40. 1105. Install both door striker plates on the VW body
More informationSTELLA AUTO SIDECAR INSTALL INSTRUCTIONS
STELLA AUTO SIDECAR INSTALL INSTRUCTIONS Open crate and inspect sidecar Remove cardboard box from inside the sidecar Remove all hardware holding the sidecar to the crate Remove sidecar from crate Remove
More informationGlideRite Retractable Cover System For HotSpring & Tiger River Spas (except Classic & pre-2000 Landmark Spas)
List of Contents Quantity Description 12 #10 x 1 ½ Flat Head Phillips Screw (see pg. 2) 2 #10 x ½ Pan Head Phillips Screw (see pg. 2) 8 ¼ x 2 ½ Lag Bolt (see pg. 2) 7 ¼ 20 x 5 / 8 Hex Head Bolt (see pg.
More informationOTHER TOOLS MAY BE NEEDED DEPENDING ON YOUR VEHICLE.
THIS KIT INCLUDES: 16 M8-1.25X40MM BOLTS WITH WASHERS 2 SHOCKS 720 PSI RIGHT AND LEFT HINGE ASSEMBLY 2 SHOULDER BOLTS 2 PINS TOOLS REQUIRED FOR INSTALLATION: AIR RACHET, GRINDER AND CUTTER. 10MM, 11MM,
More informationPage 1 of 12 GENERAL INSTRUCTIONS KHJKK Installation
Page 1 of 12 KHJKK PICTURE ABOVE IS THE UNIVERSAL KIT; YOUR KIT MAY BE DIFFERENT. THIS KIT INCLUDES: 8 M8-1.25X30MM BOLTS WITH WASHERS 8 M8-1.25X40MM BOLTS WITH WASHERS 2 PINS RIGHT AND LEFT HINGE ASSEMBLY
More informationMM Strut Tower Brace, GT (MMSTB-5.1)
3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM Strut Tower Brace, 1996-97 GT (MMSTB-5.1) MMSTB-5.1 is for 1996-97 GT s with
More informationINSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058
INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationInstallation Instructions
DODGE 16K Industry Standard Rail Custom Mounting Kit #2728 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationAssembly Instructions 10 X 10 Aluminum Frame Building
Assembly Instructions 10 X 10 Aluminum Frame Building 27 97 9 8 47 36 74 52 10 10 X 10 Square Building W/ Dome Includes: The Steel Entry Door with a Dead Bolt Lock assembly and Aluminum Door Frame. Metal
More informationINSTALLATION INSTRUCTIONS / DODGE RAM CREW CAB 2500/3500
INSTALLATION INSTRUCTIONS 225019 / 225019-2 2010 DODGE RAM CREW CAB 2500/3500 PARTS LIST: Qty Description Qty Description 1 Driver/Left Side Bar 4 Plastic Square Retainer 1 Side Bar 2 12mm x 120mm Hex
More informationINSTALLATION & OWNER S MANUAL
INSTALLATION & OWNER S MANUAL CAB INSTALLATION INSTRUCTIONS JOHN DEERE GATOR TS, TX, and TH HARD SIDED CAB KIT (p/n: GTSAS) SOFT SIDED CAB KIT (p/n: GTSSS) The contents of this envelope are the property
More informationINSTALLATION INSTRUCTIONS 6 OVAL BENT END SIDEBARS DODGE RAM 1500, CREW CAB PART#: /241533B
PARTS LIST: 1 Driver/Left Sidebar 24 8mm x 24mm x 2mm Flat Washers 1 Passenger/Right Sidebar 12 8mm Lock Washers 3 Driver/left, Passenger Center and Rear 6 8mm Hex Nuts 3 INSTALLATION INSTRUCTIONS 6 OVAL
More information6625 WEST WILSHIRE BLVD. OKLAHOMA CITY, OK (405) FAX (405)
INSTALLATION INSTRUCTIONS FOR THE TAILGATE WITH LATCH AND LINK ASSEMBLY 76-87 FORD SHORT & 53-87 FORD LONG FLARESIDES 1. Assemble the bed and make sure the box is square. Measure the distance between the
More informationTech Sheet. T4 Interior conversion kit how to - fitting instructions. 1. Rear seat belts. 2.
Page 1 of 8 T4 Interior conversion kit how to - fitting instructions Thank you for purchasing our T4 interior conversion kit. This kit will enable you to convert any SWB left hand loading door T4 into
More informationMM Strut Tower Brace, Cobra (MMSTB-7)
The MM strut Tower Brace attaches to each strut tower and to the firewall. 3430 Sacramento Dr., Unit D San Luis Obispo, CA 93401 Telephone: 805/544-8748 Fax: 805/544-8645 www.maximummotorsports.com MM
More informationINSTALLATION INSTRUCTIONS KK-K9-F14-K K9 KIT FOR FORD EXPEDITION
INSTALLATION INSTRUCTIONS KK-K9-F14-K-32 32 K9 KIT FOR 2003-2016 FORD EXPEDITION TOOLS REQUIRED: Power Drill Drill Bit Set Standard & Metric Socket Sets Phillips Screw Driver Open End Wrench Set Wire Cutters
More informationInstallation Guide 40670
Installation Guide 40670 Kargo Master Rancho Cordova, CA 95742 800-343-7486 CustomerService@KargoMaster.com DATE: Installation Instructions 40670 *PLEASE READ ALL INSTRUCTIONS AND WARNINGS PRIOR TO ASSEMBLING,
More informationCORVETTE Page 1 of 12 CORVETTE C
CORVETTE 2005-2006 Page 1 of 12 CORVETTE C5 1997-2004 THIS KIT INCLUDES: 8 M8-1.25X40MM BOLTS WITH WASHERS 8 M8-1.25X30MM BOLTS WITH WASHERS RIGHT AND LEFT HINGE ASSEMBLY WIRE LOOM 2 SHOCKS 565 PSI 2 SHOULDER
More information- 1 - P/N REV E 9/15
INSTRUCTIONS HIGH TECH II DELUXE FLUSH UNIT ASSEMBLY The following instruction is a guideline, illustrating suggested methods, assembly sequence, and tool selection. Actual assembly may vary by each situation.
More informationINSTRUCTION BOOKLET #C0 Watch step by step installation instructions at: https://www.wallbedsbywilding.com/wallbed-installation-studio-series/ WARNING! ALL MURPHY/WALLBED SYSTEMS CONTAIN STORED ENERGY.
More informationINSTALL INSTRUCTIONS KK & KK KWIK-KIT PRISONER TRANSPORT INSERT FORD and CHEVY VAN PRISONER TRANSPORT
INSTALL INSTRUCTIONS KK-100-03 & KK-120-03 KWIK-KIT PRISONER TRANSPORT INSERT FORD and CHEVY VAN PRISONER TRANSPORT TOOLS REQUIRED: ¼ & 3/8 Ratcheting Wrenches ¼ & 3/8 Air Ratchets (recommended) 3/8 Impact
More information