Easy2Build TM. 8 x 10 Easy-Grow Greenhouse. Assembly Instructions. Smart Tech solutions

Transcription

1 EasyBuild TM Smart Tech solutions 8 x 0 Easy-Grow Greenhouse Assembly Instructions 0 Structure 7 PC SHELL Systems Trading Corporation 50 7th Avenue Suite 809, New York, NY 03 Customer Service: (877) ext customerservice@stcaustin.com

2

3 Introduction Thank you for purchasing your EasyBuild TM 8x0 Easy-Grow Greenhouse. This model features two roof vents and a circular air vent to ensure proper ventilation. We have also included an automatic vent opener to help you maintain optimal temperature effortlessly. When properly assembled and maintained, this greenhouse will provide years of enjoyment. These instructions include helpful hints and important information needed to safely assemble and properly maintain the greenhouse. Please carefully read these instructions completely before you begin. This greenhouse has been designed with patented technology to be easily assembled. All but one step can be completed by one person. You will require assistance from another person to attach the roof. Although the greenhouse can be assembled in six to eight hours, we recommend that you take your time and make it aweekend project. Before Starting Assembly: CAREFULLY READ ALL INSTRUCTIONS BEFORE YOU BEGIN AND FOLLOW THE STEPS IN THE ORDER THEY ARE PRESENTED.. Make sure you have all the necessary parts: Compare the contents of the two cartons to the List of Parts. If any parts are missing or damaged or you have any questions, please contact Customer Service by phone at (877) ext. or by at customerservice@stcaustin.com before beginning assembly.. Lay the parts out in separate staging areas: The List of Parts has the corresponding step number referenced to each part. We recommend that while you go through the list, make staging areas for each step and place the parts necessary fo step in these areas. This will save you time and effort during assembly. 3. Select a Location: When selecting a site for your greenhouse, a flat level area is essential and if possible, with proper water drainage and easy access to power and water necessary for greenhouse gardening. Choose a sunny, level position away from overhanging trees and power lines and protected from the wind as much as possible. The location should be away from structures that could cause snow to drift on or around the greenhouse. Locate underground pipes or cables before preparing the site or anchoring the greenhouse. Note: You may assemble the greenhouse on a hard level surface and move it to its final position when finished. Make sure there are no obstacles between the assembly area and the final position.. Prepare a Foundation: After choosing a location, proper preparation of the site is essential. The site must be level. If the site is not level, create a base slightly larger than the outside dimensions of the greenhouse using a perimeter of two by fours filled with either soil, sod or gravel. Make sure the base is square by measuring the diagonals from both sides and making sure they are equal. The greenhouse is secured from the inside with pegs into holes cast with concrete. See step6 for details. If you decide to have a concrete base, it is best to contact a reliable contractor to ensure it is flat and level.make sure you have checked with your local authorities regarding any required building permits. 5. Make sure you have the proper tools: Tape Measure Work Gloves Safety Goggles Phillips Screwdriver Spirit Level Small Step Ladder Wooden Mallet Liquid Soap or WD0 Lubricant Scissors Hex Key (included) NOTE: A cordless drill with Phillips head bit is highly recommended but not essential. of 57

4 Safety Advice The greenhouse must be positioned and fixed on a flat level surface. Dispose of all plastic bags safely. Keep them out of the reach of small children. Keep children and pets away from the assembly area until the work is completed. Always wear shoes, gloves and safety goggles when working. In manufacturing all sharp edges and burs have been removed but caution should still be taken when handling metal parts. Do not lean against or push the greenhouse during assembly. Take special care not to touch overhead power lines with the aluminium profiles. Do not attempt to assemble the greenhouse in windy or wet conditions. Do not position your greenhouse in an area exposed to excessive wind. If using power tools or a step ladder always follow the manufacturers safety instructions. Hot items such as recently used grills, blowtorches etc. must not be stored in the greenhouse. Store the polycarbonate panels in a cool dark place like a garage until you are ready to use them. Make sure the greenhouse complies with local building codes. Table of Contents Introduction... Safety Advice... General Order of Assembly... List of Parts... 3 Assemble Back... 6 Assemble Doors... 5 Assemble Front... 9 Assemble Sides... 7 Prepare Shelves... 3 Connect Sides to Back Connect Sides to Front Assemble and Connect Gables... 0 Brace Sides... Assemble and Install Roof Vents... 6 Install Circular Vent Install Side and Roof Panels... 5 Install Weather Stripping... 5 Install Trim Plates Weather Strip and Hang Doors Secure to Ground Install Trays and Bin Holder General Order of Assembly Step : Assemble Back Step : Assemble Doors Step 3: Assemble Front Step : Assemble Sides Step 5: Prepare Shelves Step 6: Connect Sides to Back Step 7: Connect Sides to Front Step 8: Assemble and Connect Gables Step 9: Brace Sides Step 0: Assemble and Install Roof Vents Step : Install Circular Vent Step : Install Side and Roof Panels 5 Step 3: Weather Stripping Step : Install Trim Plates Step 5: Weather Strip and Hang Doors Step 6: Secure to Ground Step 7: Install Trays and Bin Holder of 57 7

5 List of Parts The greenhouse is shipped in three cartons. These cartons are heavy. Be careful when lifting them. Wear proper safety gear including work shoes, gloves and goggles. The parts are identified by removable stickers. Place all the parts for each step in staging areas, checking that you have all parts as you go. If any parts are missing or damaged, contact STC customer service before beginning assembly: Customer Service: (877) ext. or L0C L0D L0I L0J L0K L0L Step Step Step Step Step 3 Step 3 L0A L0B Steps,3 Steps,3 L0G L0H L0I L0J L0K L0L Step 8 Step 8 Step Step Step 3 Step 3 L06A Step 3 L06J Step 3 L06K Step 3 L07A L07B L07C Step Step Step L07D Step L08A L08B Step 8 Step 8 L03B L03C Step Step L03D L03K Step Step L03L Step L03T Step Step L03M L03N L03Q L03R L03S L03U Step 8 Step 8 Step 8 Step 8 Step 8 Step 8 L0A Step 0 LA Step 0 LB Step 0 L3B L3C L3D L3E L3G L3H Step Step Step Step Step Step L05D L0A Step 3 L0B Step L0C L0D L0F Step Step Step L0G Step 7 L05A L05C L05D L05F L05G L05H L05I Step Step 3 Step 0 Step Step 0 Step Step L3F LA LB LC LD LI LJ LK LL LM LN Step Step 5 Step 5 Step 5 Step 5 Step Step Step 5 Step 5 Step 5 Step 5 3 of 57

6 Panel Y Step S03 6 Step Y5 Step 3 S0 Steps,3 Y6 Step 3 Y9 Step S05 Steps,3 Y0 6 Step S09 Steps,3 Y6 Step Y7 Step S0 Steps,3 Y8 Step S Step Y9 Step 3 S8 Step 3 Y0 Step 3 Y Step S9 Step Y Step S Step 8 Y3 Step S8 0 Steps,3 Y Step 0 Y5 Step S39 Step Y6 Step of 57

7 Trim Plate L09A L09B L09C L09D Step Step Step Step Bracing Parts S06 S07 S6 hex key Steps,3,9 8 Step 9 Steps,3 Steps,3,9 rubber Door Lock Roof Vent Handle J0L Step J0R Step J03 Step J06 Step stripping J0B.5M Steps 3,5 Circular Vent Door Handle Shelf Trays circular vent vent frame plastic nut S9 S30 S3 S3 S33 J05 J05A J05B S0 S0A Step Step Step Step Step Step Step Step Step 7 Step 7 Step 7 Step Step Anchor Clip and Peg S3 L5A S3 S35 S0 S08 S08C S S7L 9 Step Step Step 6 Step 6 Steps,3, Steps, Step 3 Step Step 3 Auto Vent Opener S0 S3 S S SA S6 S S5 Step 0 S Step 0 SA Hair Pin Clip Steps,,3,,8 Steps,,0 Steps,,0 Step 0 Step 0 Step 0 Step 7 Step 0 Step 0 5 of 57 S7R S0 S S37 L6 Step 3 6 Step 3 Step 8 Steps 5,7 3 Steps,3

8 Assemble Back Place all the parts for the back face on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. The back is assembled with the outside face to the ground. ALL VIEWS ARE SHOWN FROM INSIDE..A Slide short side of connector S0 into channels of profiles L0A and L0B. Line up last hole on connector S0 with hole in each profile. IMPORTANT: The holes are not at the midpoint of the profile. Arrange profile so the 8 portion will be the bottom when standing..b Secure with S0 screws. L0A L0B S0 8 (7 mm).a Line up bottom hole on short side of connectors S0 with hole on side of profiles L03C and L03D. S0 L03C L03D S0.B Secure with S0 screws. S0 8 (7 mm) NOTE: ALL VIEWS ARE FROM INSIDE. #L0A #L0B #L03C #L03D #S0 #S0 6 6 of 57

9 .3A Attach profiles L0B and L03C to profile L0F by sliding the long sides of connector S0 into channels lining up last hole in S0 with holes in profile L0F. Attach profiles L03D and L0A to profile L0F by sliding the long side of connector S0 into profile channels lining up last hole of S0 with holes in L0F. L0B L03C L03D L0F L0A L0F.3B Secure with four S0 screws. L03C L03D L0B L0F L0A L0F S0 NOTE: ALL VIEWS ARE FROM INSIDE. S0 Screw #L0F #S0 7 of 57

10 .A Slide connector L6 inside profiles L03L and L03K. The two end holes on each side of connector L6 line up with the two holes on each profile..b Secure with four S0 screws. L03L S0 L03L S0 L03K L6 #L03K #L03L #L6 #S0.5A Slide connectors S08 into channels of profiles L03C, L03D and L03K..5B Secure each connector with two S0 screws. L03K L03L S0 L0B L03C S08 L03D L03K L0A S08 S08 NOTE: ALL VIEWS ARE FROM INSIDE S08 #S0 #S of 57

11 .6A Slide connector L6 inside profiles L0I and L0J..6B Line up the outside holes on L6 with second hole on profiles L0I and L0J. Secure with two S0 screws. L0I L0I L6 L0J NOTE: ALL VIEWS ARE FROM INSIDE L0J #L0I #L0J #L6 #S0.6C Slide connectors S0 into profile L0I and connector S05 into profile L0J until they securely click into place. s S0 and S05 CLICK into place. S0 S05 L0I L0J S0 L0J L0I S05 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. #S0 #S05 9 of 57

12 .7A Carefully line up connector S0 with profile L0B and connector S05 with profile L0A. Slide profiles L0I and L0J half way into place. Continue sliding until connectors S0 and S05 click securely into profiles. NOTE: ALL VIEWS ARE FROM INSIDE. L03L.7B Line up holes on connectors S08 with holes in profiles L0I and L0J. Secure each connector with two S0 screws. L0B L03C L03K L0I S08 S0 L03D S0 L0I L0A s S0 and S05 CLICK into place. L0J S05 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. Screw #S0 6.8A Slide hex bolt S3 into channels of profiles L05A and L05H as shown..8b Screw hex nut S onto bolt. Do not completely tighten. L05A S L05H L05A L05H S3 #L05A #L05H Nut / Bolt #S3 #S of 57

13 .9A Remove protective plastic from both sides of panels Y, Y6, Y7 and Y8. Place side to face toward the sun facing down. Fit panels Y and Y6 into bottom channel of profiles L05A and L05H. L05A L05H L05H L05A Y Y6 Y6 Y Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN..9B Slide panels and profiles L05A and L05H into V-channels on profiles L0A, L0B, L03C, L03D and L03L. NOTE: ALL VIEWS ARE FROM INSIDE..9C Slide panels Y7 and Y8 into V-channels on profiles L0A, L0B, L03C, L03D and L03L. Fit inside channels on profiles L05A and L05H. Y Y6 Y6 Y Y8 Y7 Y7 L03C L03L Y8 L0B L03D L05A Y L05H Y6 L05H Y6 L05A Y L0A Panel Panel #Y #Y7 #Y6 #Y8 of 57

14 .0 Slide hex nut S and hex bolts S3 into U-cutout in both sides of profiles L03C, L03D and L03K. Tighten securely to hold in place. L05A L05H L05H L03C L05A L03K L03D NOTE: ALL VIEWS ARE FROM INSIDE..A Slide profiles L0I and L0J into connectors S09, S0 and S until they click into place. s S09, S0 and S CLICK into place. S L0I S L0I L0J S09 L0J L0I L0J S0.5 (63 mm) S09.5 (63 mm) IMPORTANT: The holes are not at the midpoint of the profiles. Arrange profile so the.5 portion will be the bottom when standing. S0 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. #L0I #L0J #S09 #S0 #S of 57

15 .B Slide connectors S09 and S0 half way into profiles L0A and L0B. Continue sliding together making sure panels Y7 and Y8 fit into V-channels of profiles L0I and L0J. s click S09 securely into profiles. L0I Y8 Y7 Y7 L0J L0B Y8 S0 S09 L0A L0B S0 s S09 and S0 CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. L0A.A Place connectors S onto profiles L0I and L03C, L0J and L03L and L0J and L03D matching up all holes. S L0I L03C L03L L0J L03D.B Screw S0 screws partially into bottom two holes. Do not tighten. S0 S0.C Screw S0 screws into top two holes. Tighten all screws. Repeat for both sides. NOTE: ALL VIEWS ARE FROM INSIDE. S0 S0 #S0 #S 3 3 of 57

16 .3A Insert long side of cable connector S06 at an angle into profile channel L0B with HOOK FACING UP. Slide connector to other side of channel. Use hex key to securely tighten and hold in place. L0B Y L0F Y6 Y6 Y L0F L0A L0I.3B Attach one side of short cable S6 to hook on S06 and lace under profile L0F. Attach other side of cable to a second S06 cable connector and with hook facing center, insert into profile channel L0I. Push the S06 connector towards center until profile corners are square and cable is tight. Use hex key to securely tighten and hold in place. L0J L03C IMPORTANT: Make sure all corners are squared at 90 degrees. NOTE: ALL VIEWS ARE FROM INSIDE. L0I L0I. Repeat step.3 inserting cable connectors S06 into profiles L0A and L0J. Cable rests next to panel Y, under profile L0F. Slide connector until profile corners are square and cable is tight. Use hex key to securely tighten second connector and hold in place. L03D L0B Y L0F Y6 Y6 Y L0F L0A L0J L0I IMPORTANT: Make sure all corners are squared at 90 degrees. L0J L0J Hex Key Cable #S06 Cable #S6 of 57

17 Assemble Doors Place all the parts for both doors on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. Both doors are assembled with the outside face to the ground. ALL VIEWS ARE SHOWN FROM INSIDE..A Slide three hex bolts S3 into channel of profile L05I. L05I.B Screw two S hex nuts onto bolt on each end. Do not completely tighten. S3 L05I S. Remove protective plastic from both sides of panels Y5. Place side to face toward the sun facing down. Fit panels into channels of profile L05I. Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN. L05I Y5 L05I.3 Place door profiles L3B, L3C and L3E next to connectors S8 around Y5 panels as shown. Slide connectors into profiles. Make sure panels and profile L05I fit into V-channels of each profile. S8 connectors will be secured to profiles in Step. Y5 L3E S8 L3B S8 S8 Y5 L3C Y5 S8 NOTE: ALL VIEWS ARE FROM INSIDE. S8 L3E Panel #Y5 #L05I Bolt / Nut #S3 #S 3 #L3B #L3C #L3E #S8 5 of 57

18 .A Slide hex nuts and bolts into U-cutout in side of profiles L3B and L3C. Tighten securely to hold in place..b Secure connectors with six S0 screws. NOTE: The holes at the top of profile L3B and the bottom left corner of profile L3E will be secured in Step.5. L3E L3E L3B Y5 L3B L3C Y5 L3E L3C L3E Screw #S0 6.5 Place brace L5A onto door lining up the holes on each end with the holes in profiles L3E and L3B. Slide hex bolt so it fits through hole in brace. Secure brace with two S0 screws and S hex nut. S0 S L3E L3B L3C L5A S0 L3E NOTE: The hole for hex bolt is not at the midpoint of brace. Turn brace until all holes line up. Brace will dip slightly when hex bolt is secured. NOTE: ALL VIEWS ARE FROM INSIDE. Brace #L5A Screw / Nut #S0 #S 6 of 57

19 .6A Open door handle kit and remove parts. Slide pin S9 through handle S30, washer S3and hole in profile L3C into washer S3. S30 S9 S3 L3C S3.6B Slide washer S3 into groove on pin S9 to hold securely in place. L3C S3.6C Hook one side of spring S33 into hole on handle S30. Hook the other side into pin hole on profile L3C. NOTE: s packaged as Door Handle Kit. S33 #S3 L3C #S9 #S3 #S30 #S33.7A Slide two hex bolts S3 into channel of profile L05F. L05F.7B Screw two S hex nuts onto bolt on each end. Do not completely tighten. S S3 L05F.8A Remove protective plastic from both sides of panels Y6. Place side to face toward the sun facing down. Fit panels into channels of profile L05F. Y6 L05F Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN. Y6 Panel Bolt / Nut #Y6 #L05F #S3 #S 7 of 57

20 .8B Place door profiles L3D, L3F, L3G and L3H next to connectors S8 around Y6 panels as shown. Slide connectors into profiles. Make sure panels and profile L05F fit into V-channels of each profile. L3G S8 L3F S8 S8 Y6 L05F L3H Y6 S8.8C Secure connectors with eight S0 screws. S8 L3D L3G S0 L3F.8D L3H Slide hex nuts and bolts into U-cutout in side of profiles L3F and L3H. Tighten securely to hold in place. L3D NOTE: ALL VIEWS ARE FROM INSIDE..9A L3G Place S0 locks on profiles L3D and L3G as shown. Center the levers so the screw holes are visible. S0 L3F.9B Secure each S0 lock with two S0A screws. S0A S0A L3G L3D S0 L3H S0 S0 L3D.9C Move lever to the right side to place lock in the unlocked position. L3G L3D IMPORTANT: Install door locks so levers face the panels. L3G L3D NOTE: Door locks are shown in the UNLOCKED positition. When door is installed in Step 5 and door is closed, move lever to the left side to lock door. #L3F #L3D #L3G #L3H Lock #S0 #S0A Screw #S0 8 #S8 8 of 57

21 Assemble Front Place all the parts for the front face on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. The front is assembled with the outside face to the ground. ALL VIEWS ARE SHOWN FROM INSIDE. 3.A Lay out profiles L0A, L0B, L06A and L06K so all holes line up. Slide short side of connector S0 into channels of profiles L0A, L0B, L06A and L06K. L06K L06A S0 S0 L0A L06A L0A L0B S0 S0 L0B L06K IMPORTANT: The holes are not at the midpoint of the profile. Arrange profile so the 8 portion will be the bottom when standing. 8 (7 mm) 8 (7 mm) 3.B Line up lower hole on connector S0 with hole in each profile and secure with S0 screws. L06K L06A L0A L0B S0 NOTE: ALL VIEWS ARE FROM INSIDE. #L0A #L0B #L06A #L06K #S0 #S0 9 of 57

22 3.A Slide profiles L06J into L06A and L06K using connectors S8. S8 connectors do not snap into place. S8 L06J S8 S8 L06K L06A S7L L06J 3.B Place connectors S7L and S7R on corners matching up bottom two holes with holes in profiles L06A, L06J and L06K as shown. L06K S7R L06A 3.C Secure each connector with S0 screws. S7L S7R S7L S7R L06K L06A S0 #L06J #S8 #S7L #S7R 3.3A Attach profiles L0B and L06K to profile L0A. Slide long sides of connectors S0 into channels of profile L0A, lining up last hole in S0 with holes in profile L0A. 3.3B Secure with S0 screws. Attach profiles L06A and L0A to profile L0A. Slides long side of connectors S0 into channels of profiles L0A, lining up last hole of S0 with holes in L0A. L0B L06K L06A L0B L06K L0A L06A L0A L0A S0 L0A L0A L0A S0 NOTE: ALL VIEWS ARE FROM INSIDE. #L0A Screw #S0 0 of 57

23 3.A Slide profiles L0K and L0L into connectors S09, S8 and S0 until they click into place. s S09, S0 and S8 CLICK into place. S8 L0K S8 L0K L0L L0L S09 L0K L0L S0 6.5 (676 mm) 6.5 (676 mm) S09 IMPORTANT: The holes are not at the midpoint of the profiles. Arrange profile so the 6.5 portion will be the bottom when standing. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. S0 #L0K #L0L #S09 #S0 #S8 3.B Remove protective plastic from both sides of panel Y0. Place side to face toward the sun facing down. Fit panel into V-channel on profile L06J. Y0 Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN. L06J Y0 L06J NOTE: ALL VIEWS ARE FROM INSIDE. Panel #Y0 of 57

24 3.5A Slide connectors S09 and S0 half way into profiles L0A and L0B. Continue sliding together making sure panel Y0 fits into V-channels of profiles L0L and L0K. s S7L and S7R L0K rest in channels of L0L and L0K. s S09 L0L and S0 click securely into profiles. Y0 S09 S7L S7R S09 L0B S0 S0 L0A L0B L0A s S09 and S0 CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 3.5B Loosen the four screws in connectors S7L and S7R enough to adjust door frame profiles L06A, L06J and L06K and align with gable profiles L0L and L0K. Secure connectors S7L and S7R to profiles L0K and L0L with two S0 screws and tighten four screws connecting profiles L06A, L06J andl06k. L0K S7L L06J S7R L0L L06K L06A L0K S0 L0L S7L S0 S7R ALL VIEWS FROM INSIDE. IMPORTANT: Make sure all profiles are aligned before tightening connectors S7L and S7R with S0 screws. Screw #S0 of 57

25 3.6A Remove protective plastic from both sides of panels Y5, Y6 and Y9. Place side to face toward the sun facing the down. Fit panels Y9 into top channels of L05C. Y9 IMPORTANT: Make sure to assemble a right and left side. Y9 Y9 L05C L05C L05C Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN. 3.6B Slide Y9 panels into V-channels on profiles L0A, L0B, L06A and L06K. Note Y0 panel sits next to panel Y9. L0B L06K Y0 L06A L0A Y0 Y9 NOTE: ALL VIEWS ARE FROM INSIDE. Y9 L05C Y9 L05C 3.6C Slide Y5 and Y6 panels into V-channels on profiles L0A, L0B, L06A and L06B. Fit inside channels on L05C profiles. Y0 Y9 L05C Y9 L05C L0B L06K L06A L0A Y6 Y5 Panel Panel Panel #L05C #Y6 #Y5 #Y9 3 of 57

26 3.7A 3.7C Line up connector S08C with holes on profiles L0K as shown. L0K S08C Slide connector L6 inside profiles L0K and L0L. 3.7D 3.7B L0K Secure with two S0 screws. S0 Line up outside holes on connector L6 with holes on profiles L0L and L0K. Secure with four S0 screws. L0K L0K 3.8A S0 L6 Slide short side of connectors S0 into channels of profiles L0K and L0L. Line up last hole on connector with holes on profile. 3.8B L0L S0 Secure with two S0 screws. S0 S0 L0L L0K L0K S0 L0L L0L NOTE: ALL VIEWS ARE FROM INSIDE. S0 #L0K #L0L #S0 #S08C #S0 #L6 #S0 #S0 3.8C Slide connectors S0 into profile L0K and connector S05 into profile L0L until they securely click into place. S05 S0 L0K L0L S0 L0K L0L S05 s S0 and S05 CLICK into place. #S0 #S05 of 57

27 3.9A As you slide bottom profiles L0L and L0K half way into place, carefully line up S0 connectors with channels on profiles L06K and L06A and S0 and S05 connectors with profiles L0B and L0A. Continue sliding, making sure panels Y6 and Y5 fit into V-channels. Snap connectors S0 and S05 securely into profiles. L06A S0 Y6 Y5 S05 L0L L0B L06K L06A s S0 and S05 CLICK into place. L0A L06A S0 S0 S0 L0K L0L S05 L0L S05 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 3.9B Secure S0 connector to profiles L06A and L06K with S0 screws. L06A S0 NOTE: ALL VIEWS ARE FROM INSIDE. L0L Screw #S0 5 of 57

28 3.0A Insert long side of cable connector S06 at an angle into profile channel L0B with HOOK FACING UP. Slide connector to other side of channel. Use hex key to securely tighten and hold in place. L06A Y5 L0A Y6 L06K L0B L0L L0K NOTE: ALL VIEWS ARE FROM INSIDE. 3.0B Attach one side of short cable S6 to hook on S06 and lace under profile L0A. Attach other side of cable to a second S06 cable connector and with hook facing center, insert into profile channel L0K. Push the S06 connector towards center until profile corners are square and cable is tight. Use hex key to securely tighten and hold in place. L06K IMPORTANT: Make sure all corners are squared at 90 degrees. L0K L0K 3. Repeat step 3.0 inserting cable connectors S06 into profiles L0A and L0L. Cable rests next to panel Y5, under profile L0A. Slide connector until profile corners are square and cable is tight. Use hex key to securely tighten second connector and hold in place. Y6 L06K L06A Y5 L0A L0A L0B L0A L06A L0L L0L L0K IMPORTANT: Make sure all corners are squared at 90 degrees. L0L Hex Key Cable #S06 Cable #S6 6 of 57

29 Assemble Sides Place all the parts for the sides on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. You are assembling both sides in the following steps. Both sides are identical until Step.8.A Line up the four profiles so the holes are at the same position. Slide short side of connectors S0 into channel of profile until the last hole in S0 lines up with third hole from the bottom on profile. IMPORTANT: The holes are not at the midpoint of the profile. Arrange profile so the 8 portion will be the bottom when standing. L03A S0.B Slide another connector S0 so it lines up with the middle hole on profile. S0.C Secure all pieces with S0 screws. Repeat to make four sets. S0 S0 6 / (65 mm) 8 (75 mm) # #S0 #S0 8 8.A Lay out profiles L0D so the holes are at the same position. Slide short side of connector S0 into channel of profile, lining the last hole in S0 with the hole on profile L0D. S0.B Secure with S0 screw. Repeat to make four sets. L0D NOTE: ALL VIEWS ARE FROM INSIDE. S0 #L0D #S0 #S0 7 of 57

30 .3 Slide connector S39 into profile L0D until it snaps into place. Repeat to make four sets. S39 S39 L0D S39 CLICKS into place. #S39. Slide connector S03 into profile L0B until it clicks into place. S03 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. S03 L0B S03 CLICKS into place. #L0B #S03.5A Attach profiles L0B and L0C to profile by sliding the long sides of connectors S0 into the channels. The last hole of connector S0 lines up with the holes in the profiles..5b Secure with two S0 screws. Repeat to make four sets. IMPORTANT: S03 rests on top of connector S0. S0 screw secures S03 to profile L0B. S0 L0B L0B L0C S03 S0 S0 L0C S0 NOTE: ALL VIEWS ARE FROM INSIDE. #L0C Screw #S0 8 8 of 57

31 .6A Connect profile L0D by sliding connector S39 into profile L0B until it snaps in place. Slide connector S0 into channel of L0C..6B Secure with S0 screw. Repeat to make four sets. S39 CLICKS into place. S39 L0B S39 L0C L0D S0 Screw #S0 S0 There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves..7a Slide long side of connectors S0 and S08 into channel of profile. S0.7B Secure with three S0 screws. Repeat to make four sets. S0 S0 S08 S08 S0 NOTE: ALL VIEWS ARE FROM INSIDE. #S0 #S0 #S0 #S of 57

32 .8A Line up the four profiles L03B so the holes are at the same position. Slide long side of connectors S0 and S08 into channel of profile, lining up holes as shown. S0 L03B.8B Secure with three S0 screws. Repeat to make two sets. S0 S0 L03B S08 #L03B #S0 #S0 #S0 #S08.9A Place profiles L03B and onto profiles L07C and L0D. Line up holes as shown..9b Secure with six S0 screws. L07C L07C L07C L03B L03B L07C L03B L0D NOTE: ALL VIEWS ARE FROM INSIDE. L0D L0D S0 Screw #L0D #L07C #S of 57

33 .0A Place profiles L03B and onto profiles L07D and L0D. Line up holes as shown..0b Secure with six S0 screws. L07D L07D L07D L03B L07D L03B L03B L0D L0D S0 L0D Screw #L0D #L07D #S0 6. Slide connectors S9 and S03 into profile L03T until they click securely into place. Repeat to make two sets. S9 S9 NOTE: ALL VIEWS ARE FROM INSIDE. L03T L03T L03T S03 S03 #L03T #S03 #S9 3 of 57

34 .A Place profiles onto profiles L07A and L0C. Line up holes as shown. L07A.B Secure with three S0 screws. L07A L07A L0C NOTE: ALL VIEWS ARE FROM INSIDE. L0C S0 L0C Screw #L0C #L07A #S0 3.3A Place profiles onto profiles L07B and L0C. Line up holes as shown..3b Secure with three S0 screws. L07B L07B L07B L0C L0C L0C S0 Screw #L0C #L07B #S0 3 3 of 57

35 .A Carefully slide sections together as shown to make the left side of the greenhouse. We recommend using two people for this step. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. L07D S9 L07B L07B S9 L07D L03T S03 S39 LI L03B S03 LJ L0C S39 S03 L0D L0D S03 L0C s S03, S9 and S39 CLICK into place..b Use two people to carefully slide the remaining two side sections together as shown to make the right side of the greenhouse. S9 NOTE: ALL VIEWS ARE FROM INSIDE. L07A L03T L07C S03 L03B S39 LI L07A S9 S03 LJ L0D L07C S39 S03 L0C L0C S03 L0D s S03, S9 and S39 CLICK into place. #LI #LJ 33 of 57

36 Prepare Shelves Place all the parts for the shelves on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. 5.A Line up the shelf profiles so the holes are at the same position. Slide long side of connector S37 into channel of each profile, lining up the last hole on the connector with the hole in the channel. LB LN LC S37 LD LK S37 LL LA LM IMPORTANT: The shelf profiles have rectangular holes in the channel or side of one end. Slide connector S37 into other side, lining up last hole in connector with hole in the channel. 5.B Secure with S0 screw. S37 S0 #LA #LM #LB #LN #LC #LK #S37 #S0 8 8 #LD #LL 3 of 57

37 Connect Sides to Back 6.A With the outside facing a wall, carefully stand back up and lean against the wall. Stand each side up and place next to the back. Both sides are identical until the shelf profiles are connected. Make certain that positions of profiles L07A and L07B match the diagrams before connecting. Stand the left side facing inside with L07B next to the back. Slide shelf profile LK into connector S03 until it clicks into place. Slide shelf profile LL into connector S39 until it clicks into place. L07B S03 LK LL L07D S03 LK LL S39 S39 L0C s S03 and S39 CLICK into place. 6.B L0D Carefully slide left side into back, lining up connectors with profiles. Move side so connectors S09 and S0 are half way into profiles L07B and L0C. s S37 rest on top of profile L0F. Push side in until connectors click into place. S37 L0F L07B S09 S09 S37 L07B S37 L0F Secure connectors S37 to profile L0F with two S0 screws. LK LL S37 S0 S0 L0F S0 L0C L0C S0 VIEWS FROM INSIDE. s S0 and S09 CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. Screw #S0 35 of 57

38 6.A Stand the right side facing inside with profile L07A next to back. Slide shelf profile LM into connector S03 until it clicks into place. Slide shelf profile LN into connector S39 until it clicks into place. L07A LN LM S03 LN S39 LM S03 S39 s S03 and S39 CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 6.B Carefully slide right side into back, lining connectors up with profiles. Move side so connectors S0 and S05 are half way into profiles L07D and L0D. s S37 rest on top of profile L0F. Push side in until connectors click into place. S0 CLICKS into place. S0 S0 L07A L07A L0F S37 L0F LM S37 S05 LN Secure connectors S37 to profile L0F with two S0 screws. L0C S0 S0 L0F S05 VIEWS FROM INSIDE. Screw L0C S05 CLICKS into place. #S0 36 of 57

39 Connect Sides to Front Keep the structure as is, with the back against the wall until you finish this step. This will make it easier to keep the angles square. 7. Slide shelf profile LA into connector S03 on the left side until it clicks into place. Slide shelf profile LB into connector S03 on the right side until it clicks into place. LA S03 s S03 CLICK into place. L07D S03 LA L07C S03 LB S03 LB s S03 CLICK into place. VIEWS FROM INSIDE. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 37 of 57

40 7.A Lift front from inside and rest it next to sides. Line up connector S09 with profile L07C, connector S0 with profile L07D and connectors S0 and S05 with profiles L0D. S0 L07D LA S09 S05 L07C LB S0 L0D 7.B Carefully pull the front until all connectors are half way inside each profile. Make sure connector S37 attached to shelf profiles rest on top of profile L0A. Push front into sides until connectors click into place. S09 s S09 and S0 CLICK into place. L0A L07C S0 L07D S37 S09 S37 LA L07C S05 S37 LB S0 S0 L0D L0D s S0 and S05 CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 38 of 57

41 7.3A Slide shelf profile LC at a slight angle so one end slides half way into connector S39 and the other side with connector S37 rests on top of profile L0A. Continue to slide until profile clicks into connector S39. S39 CLICKS into place. LC S39 L07D S37 L0A LA LC S39 7.3B Repeat step 7.3A, sliding shelf profile LD into S39 connector. Make sure connector S37 rests on top LD of profile L0A. S39 S39 CLICKS into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 7.3C Secure S37 connectors to L0A profiles with four S0 screws. L0A LC LA L0A LD LB VIEWS FROM INSIDE. Screw #S0 39 of 57

42 Assemble and Connect Gables Place all the parts for the gables on a level surface. Make sure the pieces are in the correct positions before assembling. Please carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including shoes, gloves and goggles. 8.A Line up gable profiles with three S connectors as shown. Slide S connectors into channels of profiles L03M. Slide S connector into channels of profiles L03U. Slide S connector into channels of profiles L03R and L03S. 8.B Secure each set with S S four S0 screws. S L03M L03M L03S L03R S0 S L03S L03R L03U L03U IMPORTANT: U-shaped cutout is not at midpoint of profiles L03R and L03S. Attach shorter side (6.5 ) to connector S. #L03M #L03R #L03S #L03U #S0 #S 3 8.A Slide connector S into profiles L03Q and L03N until it clicks securely into place. IMPORTANT: U-shaped cutout is not at midpoint of profiles L03N and L03Q. Attach shorter side (6.5 ) to connector S. Make sure connector S is positioned correctly before connecting. L03N S S 8.B Line up holes on bracing bar S3 with holes in profiles L03Q and L03N. S3 L03Q L03N L03Q 8.C Secure brace to profiles with two S0 screws. L03N L03Q L03N L03Q s S CLICKS into place. S0 #L03N #L03Q #S Screw #S0 Brace #S3 0 of 57

43 8.3 From the inside of the greenhouse, use two people to carefully lower center gable onto frame. Line up and slide profiles L03N and L03Q into connectors S9 until they click securely into place. s S9 CLICK into place. L03Q S9 L03Q L03N S9 S9 L03N S9 L03N L03Q IMPORTANT: U-shaped cutouts on profiles L03N and L03Q face the FRONT. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. 8. From the inside of the greenhouse, use two people to carefully lower front and back gables onto frame. Line up and slide connectors S0 into channels of profiles L03M, L03R, L03S and L03U. L03R IMPORTANT: U-shaped cutouts on profiles L03R and L03S face the BACK. L03M L03R L03U L03S L03M L03S L03U S0 S0 S0 S0 S0 S0 S0 L03S L03R S0 of 57

44 8.5A Line up profiles L08A and L0H as shown. L08A has a cutout on one end. The plain side slides into V-channel of profile L0H. Note the rectangular holes in the channels of profile L0H are NOT on the side next to the V-channel. 8.5B Slide the plain side of L08B into V-channel on L08A opposite side of profile L0H. L08A L0H L08B L08B L08A L0H L08A L0H L0H L08B IMPORTANT: There is one correct way to connect these profiles. Arrange profiles before sliding together. Use WD0 or liquid soap if parts do not easily slde together. #L0H #L08A #L08B 8.6A Using a small step ladder inside the greenhouse, carefully slide profile L0H with L08A and L08B connected into front connector S8 at a slight angle. Gently push center gable slightly towards the back to slide other end of profile into connector S. Make sure both connectors click securely into place. Note: L0H profile rests on top of S connectors. IMPORTANT: Make sure profile L0H with L08A are in correct positions before installing. Arrange profile L0H so rectangular holes in channels face the LEFT when looking at the front of the greenhouse from the outside. S8 S L0H L08A s S8 and S CLICK into place. S S 8.6B Slide profile L0G at a slight angle into center gable connector S. Gently push back side slightly forward to slide other end of profile into connecor S. Make sure both connectors click securely into place. Note: profile L0H rests on top of S connectors. IMPORTANT: Arrange profile L0G so rectangular holes in channels face the LEFT when looking at the front of the greenhouse from the outside. S L0G S S s S and S CLICK into place. There is only one way to properly fasten connectors into profiles. Line up parts first to ensure correct placement. Slide connectors until they CLICK securely into profile. Use WD0 or liquid soap if pieces do not easily slide together. Wear gloves. #L0G of 57

45 8.7A L03S S0 From inside of greenhouse, secure S0 connectors to gable profiles L03M, L03N, L03Q, L03R, L03S and L03U with two S0 screws. S0 8.7B Secure each S connector to profiles L0G and L0H with one S0 screw. L0H S S0 L03R VIEWS FROM INSIDE. Screw S0 S0 #S0 5 VIEWS FROM INSIDE. 8.8A From inside of greenhouse, line up bracing bar S3 with holes in gable profiles L03U, L03R and L03S. Secure one S0 screw partially into each end. Then go back and tighten both screws. L03U L03U L03S L03R S0 S3 S0 S0 S3 S0 8.8B VIEWS FROM INSIDE. From inside of greenhouse, place S3 bracing bars S3 onto the center three side and gable profiles. Line up holes in profiles and L03U, L03T and L03Q, L03T and L03N, and L03R and and L03S with holes in S3 bracing bar. L03U 8.8C Secure one S0 screw partially into each end. Tighten both screws. S0 L03U S3 L03N S0 S0 L03Q L03R L03T S3 S0 S0 L03T L03S S0 S3 VIEWS FROM INSIDE. Screw #S0 6 Brace #S3 8 3 of 57

46 Brace Sides Place all the parts for bracing the sides on a level surface. Make sure the pieces are in the correct positions before assembling. Please carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including shoes, gloves and goggles. 9.A From the inside of the greenhouse, insert long side of cable connector S06 into profile channel L07C with hook facing the front. Slide connector to other side of channel. Use hex key to securely tighten and hold in place. L07C L0B IMPORTANT: Make sure all corners are squared at 90 degrees. 9.B Attach one side of long cable S07 to hook and lace behind profile LB. Attach other side of cable to a second S06 cable connector. With hook facing the back, insert connector into profile channel L0D. L0D 9.C Push towards center until profile corners are square and cable is tight. Use hex key to securely tighten and hold in place. L07C LB L0B L0D VIEWS FROM INSIDE. L0D IMPORTANT: Make sure all corners are squared at 90 degrees. 9. Repeat step 9. inserting cable connectors S06 into profile L07C with hook facing the back and into profile L0D with hook facing the front. Cable rests behind profile LB. Slide connector until profile corners are square and cable is tight. Use hex key to securely tighten second connector and hold in place. L07C L0B L07C L0D L0B LB VIEWS FROM INSIDE. L0D IMPORTANT: Make sure all corners are squared at 90 degrees. Hex Key Cable #S06 Cable #S07 of 57

47 9.3A From the inside of the greenhouse, insert long side of cable connector S06 into channel of profile L07A with hook facing the back. Slide connector to other side of channel. Use hex key to securely tighten and hold in place. L07A L0A L07A L0A 9.3B Attach one side of long cable S07 to hook and lace behind profile LM. Attach other side of cable to a second S06 cable connector. With hook facing the front, insert connector into channel of profile L0C. L03T LM L0C L0C L03T VIEWS FROM INSIDE. 9.3C Push towards center until profile corners are square and cable is tight. Use hex key to securely tighten and hold in place. L03T IMPORTANT: Make sure all corners are squared at 90 degrees. L0C 9. Repeat step 9.3 inserting cable connectors S06 into profile L07A with hook facing the front and into profile L0C with hook facing the back. Cable rests behind profile LI. Slide connector until profile corners are square and cable is tight. Use hex key to securely tighten second connector to hold in place. L07A L0A L03T LI L0C L0A L07A VIEWS FROM INSIDE. IMPORTANT: Make sure all corners are squared at 90 degrees. 9.5 L0C Repeat step 9. through 9. on the other side of the greenhouse. L03T L0B LK L07B IMPORTANT: Make sure all corners are squared at 90 degrees. L0C LI LA L07D L0A Hex Key Cable #S06 Cable #S07 6 L0D 5 of 57

48 Assemble and Install Roof Vents Place all the parts for both roof vents and handles on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles. The roof vents are assembled with the outside face to the ground. ALL VIEWS ARE SHOWN FROM INSIDE. Assemble BOTH vents first and then add the handles. IMPORTANT: This greenhouse is equipped with one MANUAL vent handle (S5 installed in step0.3) and one AUTOMATIC vent handle (auto vent opener installed in step 0.0). The auto vent opener is packed separately. 0. Remove protective plastic from both sides of panels Y. Place side to face toward the sun facing down. Fit panels into channels of profiles L0A and LA. LA Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING DOWN. LA Y L0A L0A 0.A LA LB Fit panel and profiles L0A and LA into channels of profiles LB. Make sure holes in ends of profiles line up. 0.B Secure with four S6 S6 screws. LA Y LB S6 LA Y LB S6 LB L0A LB L0A S6 LA NOTE: ALL VIEWS ARE FROM INSIDE. LB LB S6 LB L0A S6 L0A Screw Panel #S6 8 #LB #L0A #LA #Y 0.3 Attach handle S5 to profile L0A with two S screws. NOTE: You will install the handle to the second vent in step 0.0. S5 S5 IMPORTANT: hollow side of handle S5 faces down when attached. S S Y S S L0A L0A Handle #S5 Screw #S 6 of 57

49 0.A Unpack contents of Auto Vent Opener. Slide cylinder and piston rod through set collar on arm A. set collar arm A piston rod cylinder 0.B Continue sliding cylinder so piston rod fits into push arm and arm B begins to open. Align hole in piston rod with second hole in push arm. Insert hairq`pin clip to secure. hair pin clip 0.C Slide cylinder so threaded area enters set collar. Turn cylinder clockwise to screw cylinder into set collar. As you continue turning, the piston rod forces the push arm back, pushing arm A and arm B together. push arm NOTE: The Auto Vent Opener will be installed to the vent in step 0.0 cylinder push arm arm B arm A push arm cylinder Handle Cylinder with Piston Hair Pin Clip 0.5A Slide two S3 hex bolts into channel of profile L05D and four S3 hex bolts into channel of profile L05G. 0.5B Screw two S hex nuts onto bolts on ends of each profile. Do not completely tighten. S L05D L05D L05G L05G S3 Bolt / Nut #L05D #L05G #S3 6 #S 0.6A With pins facing up on the inside of the greenhouse, slide one end of profile L05D into V-channel of profile L03N. Angle it slightly to fit the other end into V-channel of profile L03S. L05D L03N L03R L05G L03Q IMPORTANT: Make sure the pins face UP on INSIDE of the greenhouse when profile L05D is installed. L05D L03S L03N L03N L05D L03S 0.6B VIEW FROM INSIDE. Line up L05D channel with U-shaped cutouts in sides of profiles L03N and L03S. Slide hex nut and bolts into U-shaped notches and tighten securely. L05D L03S L05D L03S VIEWS FROM INSIDE. 7 of 57

50 0.7 Repeat step 0.6 to install profile L05G on the other side of the greenhouse. With the nuts and bolts are facing the inside, secure profile L05G to profiles L03Q and L03R. L03R L03R L05G L03Q L05G VIEW FROM OUTSIDE. L05G L03Q L05G L03Q VIEWS FROM INSIDE. 0.8A Stand on a small step ladder inside the greenhouse. Install roof vent with handle S5 to the right side of greenhouse. Slide profile LA into profile L08A from the back of the greenhouse towards the front. IMPORTANT: The handle of roof vent is on the inside of the greenhouse. LA L08A LA Y L08A L05D 0.8B Continue to slide vent past the end of profile L08A until the hole in the other end is visible. Screw SA into hole in L08A and slide vent back until it rests next to the screw. L08A L08A YSA L05D SA Screw #SA 8 of 57

51 0.9A Stand on a small step ladder inside the greenhouse. Install second roof vent to the left side of the greenhouse. Slide profile LA into profile L08B from the back of the greenhouse towards the front. 0.9B Continue to slide vent past the end of profile L08B until the hole in the other end is visible. Screw SA into hole in L08A and slide vent back until it rests next to the screw. Y L05G LA L08B L08B SA Screw #SA 0.0A From the inside of the greenhouse open arms of auto vent slightly. Line up window bracket on arm B to holes in vent profile L0A and attach with two SA screws. arm B SA L0A L0A 0.0B Slide bolts in channel of profile L05G until they fit into holes on end of arm A. Secure with two S hex nuts. NOTE: ALL VIEWS ARE FROM INSIDE. arm A S Nut / Screw L05G L05G #S #SA 0.0C Carefully push upper handle B down until vent closes completely. Turn cylinder clockwise until threaded area of cylinder is centered to set collar as shown. L05G set collar IMPORTANT: Tighten the cylinder when you finish or the auto vent will not function. L0A cylinder cylinder 9 of 57

52 Install Circular Vent Place all the parts for circular vent on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles..a Open box containing the parts for circular vent. From the outside of the greenhouse, line up vent frame pins with holes in panel Y6, and slide into place. From the inside of the greenhouse, slide circular vent under the cable. Line up pins in vent frame with holes in circular vent and slide into place. IMPORTANT: Circular vent rests under the bracing cable. See step 3.0 for detailedinstructions on adjusting the cables..b From the inside, secure the vent with four plastic nuts. Y6.C Double check that the profile corners are squared at 90 degrees and adjust if necessary. See step 3.0 for detailed instructions. Y6 IMPORTANT: Make sure all corners are squared at 90 degrees. Vent Frame Circular Vent Plastic Nuts NOTE: VIEWS ARE FROM INSIDE. 50 of 57

53 Install Side and Roof Panels Place all side and roof panels on a level surface. Make sure the pieces are in the correct positions before assembling. Carefully follow the order of assembly to ensure an easy installation. Wear proper safety gear including work shoes, gloves and goggles.. Remove protective plastic from both sides of panels Y9 and Y0. Place side to face toward the sun facing out when installing. Slide panels carefully into V-channels in corner profiles L0A and L0B and side profiles L03B, L03T and. As you continue sliding the panels, make sure they fit into the V-channels in base profiles L0C and L0D. Y9 Y0 Y0 Y0 Y9 Y9 Y0 Y0 Y0 Y9. Remove protective plastic from both sides of panels Y, Y and Y3. Place side to face toward the sun facing out when installing. Slide panels carefully into V-channels in gable profiles L03M, L03N, L03Q, L03R, L03S and L03U and into V-channels of front and back profiles L0I, L0J, L0K and L0L. As you continue sliding the panels make sure they fit into the V-channels Y in center roof profiles L0G and L0H. Y Y3 Y Y Y3 Y Y Y Y Remove protective plastic from EACH side of poly carbonate panels before installing. Dispose of plastic properly. Install with side labeled Face this side towards the sun FACING OUT. Panel Panel Panel #Y #Y9 #Y0 6 #Y #Y3 5 of 57